Shaft Seal Program - Apex Sealing Seal Program. Apex Sealing Inc., 164 B Yankee Park Road, Fairfax, VT, 05454, USA toll free 888.730.2739, ... •Equivalent to John Crane Type 1, Pac-Seal

1Apex Sealing Inc., 164 B Yankee Park Road, Fairfax, VT, 05454, USA toll free 888.730.2739, phone 802.524.7100, fax 802.524.7112, Email: [email protected], web www.apexsealing .com

Apex Sealing Inc., 164 B Yankee Park Rd., Fairfax, VT, 05454, USA toll free: 888.730.2739 phone: 802.524.7100,

Fax: 802.524.7112,email: [email protected], Web: www.apexsealing .com

Shaft Seal ProgramShaft Seal Program


Apex SealingShaft Seal Program

Apex Sealing is proud to present you with our Shaft Seal Program. As one of the fastest growing seal companies in the U.S., our purpose has been resolute from the start; make our customers more profitable and our viability will take care of itself. You will find our product offerings meet the highest quality standard in the world. Our price structure reflects the direct access we have to some of the lowest cost manufacturing available, low overheads and reasonable profit margins.

The mechanical shaft seal industry has become an aggressively priced commodity market in the past few years. All the seal companies are now sourcing off shore with virtually identical products. We pass on to our distributor network a price structure that makes them substantially more competitive in the field. In many cases, we are adding $25-$200 to our customer’s bottom line on each new pump or pump repair sale from reduced seal costs.

Price is a moot point without quality and service. We would be happy to send you’re a sample to show the level of quality that is our standard. We are proud to be a little bit “hungry” and our growth has reflected that approach. With almost two decades of seal experience, we have been fortunate to develop a wealth of resources in the form of reliable suppliers, loyal customers, committed employees and good friends. These relationships have been the foundation to our rapid growth and in turn a valuable asset to our new customers.

Simply stated, our success will be measured by our customer’s increased profitability and confidence in our sealing capability. That is considered on every order.

Thank you for your interest.

Best Regards,

Greg Campbell


Table of Contents

IntroductionTable of ContentsType A1Type A21Type A21 MetricType A2Small Pump and Motor SealsType A8T, A9TAMG-1 SeatsMetric SeatsSeals for Unique EquipmentOther Common Sealing SolutionsApplication Data Sheet

23456789101112131415

Page


•Single spring, elastomer bellows seal•Bellows design helps compensate for face wear•Bi-directional•Torque of pump shaft drives through drive band

and notches•Rugged single spring•Multiple face and elastomer choices•Equivalent to John Crane Type 1,

Pac-Seal Type 51, US Seal E head

All industry standard “PS” numbers are available, Just provide us the “PS” number required or one used on previous orders

Type A1

D

D2

L1 L

D1

D D1 L D2 L1

SHAFT SIZE INCHES

SIMILAR INDUSTRY

PART #

Seal ODOperating

LengthSeat Bore Thickness

1.000 251V 1.500 1.562 1.625 0.4371.125 1169V 1.625 1.625 1.750 0.4371.250 1182V 1.812 1.625 1.875 0.4371.375 864V 1.875 1.687 2.000 0.4371.500 1190V 2.000 1.687 2.125 0.4371.625 1683V 2.250 2.000 2.375 0.500

1.750 858V 2.375 2.000 2.500 0.5001.875 2069V 2.500 2.125 2.625 0.5002.000 1685V 2.625 2.125 2.750 0.5002.125 1617V 2.812 2.375 3.000 0.5622.250 2091V 2.937 2.375 3.125 0.5622.375 2097V 3.062 2.500 3.250 0.562

2.500 916V 3.187 2.500 3.375 0.5622.675 328V 3.375 2.750 3.375 0.6252.750 838V 3.500 2.750 3.500 0.6252.875 329V 3.625 2.875 3.750 0.6253.000 324V 3.750 2.875 3.875 0.625

Standard Materials of Construction:Faces: Carbon Graphite (Resin Impregnated.), Ceramic, Stainless Steel , Silicon Carbide, Tungsten CarbideElastomers: Buna, Viton, EPRMetallurgy: 304, 316, Monel

Please check with the factory for operating limits and conditions


Type A21•Single spring, elastomer bellows seal•Cost effective seal common to many

process pumps•Bellows design helps compensate for face wear•Bi-directional•Multiple face and elastomer choices•Equivalent to John Crane Type 21,

Pac-Seal Type 21, US Seal C head

D

D2

L1L

D1

D D1 L D2 L1

SHAFT SIZE INCHES

SIMILAR INDUSTRY

PART #Seal OD

Operating Length

Seat Bore Thickness

0.625 290 1.062 0.875 1.250 0.4060.750 358 1.187 0.875 1.375 0.4060.875 309 1.312 0.937 1.500 0.4061.000 235 1.687 1.000 1.625 0.4371.125 356 1.812 1.062 1.750 0.4371.250 185 1.937 1.062 1.875 0.4371.375 177 2.062 1.125 2.000 0.4371.500 758 2.187 1.125 2.125 0.4371.625 238 2.500 1.375 2.375 0.5001.750 446 2.625 1.375 2.500 0.5001.875 340 2.750 1.500 2.625 0.5002.000 267 2.875 1.500 2.750 0.5002.125 543 3.000 1.687 3.000 0.5622.250 1679 3.125 1.687 3.125 0.5622.375 268 ** 3.250 1.812 3.250 0.5622.500 2120 3.343 1.812 3.375 0.5622.625 No PS 3.500 1.937 3.375 0.6252.750 836 3.750 1.937 3.500 0.6252.875 270 ** 3.875 2.062 3.750 0.6253.000 1696 ** 4.000 2.062 3.875 0.625





Type A21 Metric•Single spring, elastomer bellows seal•Cost effective seal common to many

European pumps•Bellows design helps compensate for face wear•Bi-directional•Multiple face and elastomer choices•Functional equivalent to John Crane Type 21,

Sealol 43

D

D2

L1L

D1

D D1 L D2 L1SHAFT SIZE

mmSeal OD

Operating Length

Seat Bore Thickness

14 23.9 26.4 25.0 8.6

16 26.7 26.4 27.0 8.618 30.4 27.5 33.0 10.020 33.4 27.5 35.0 10.022 33.4 27.5 37.0 10.0

24 38.0 30.0 39.0 10.025 39.3 30.0 40.0 10.028 42.0 32.5 43.0 10.030 44.0 32.5 45.0 10.032 45.8 32.5 48.0 10.0

33 45.8 32.5 48.0 10.035 49.0 34.0 50.0 11.038 52.8 34.0 56.0 11.040 55.8 34.0 58.0 11.0

43 58.8 34.0 61.0 11.045 61.0 34.0 63.0 11.048 64.0 34.0 66.0 11.050 66.0 34.5 70.0 13.055 71.7 34.5 75.0 13.0

58 78.4 39.5 78.0 13.060 78.4 39.5 80.0 13.065 84.3 39.5 85.0 13.0




•Single spring, elastomer bellows seal•Designed for shorter operating lengths than A -1•Bellows design helps compensate for face wear•Bi-directional•Torque of pump shaft drives through drive band

and notches•Rugged single spring•Multiple face and elastomer choices•Equivalent to John Crane Type 2, Pac-SealType 52, US Seal D head

Type A2

D

D2

L1 L

D1

D D1 L D2 L1

SHAFT SIZE INCHES

SIMILAR INDUSTRY PART #

Seal ODOperating


1.000 1046V 1.750 1.062 1.625 0.4371.125 604V 1.875 1.062 1.750 0.4371.250 381V 2.000 1.062 1.875 0.4371.375 491V 2.187 1.125 2.000 0.4371.500 2051V 2.312 1.125 2.125 0.4371.625 514V 2.718 1.375 2.375 0.5001.750 237V 2.750 1.375 2.500 0.5001.875 828V 2.875 1.500 2.625 0.5002.000 2073V 3.000 1.500 2.750 0.5002.125 1686V 3.250 1.687 3.000 0.5622.250 846V 3.375 1.688 3.125 0.5622.375 594V 3.500 1.812 3.250 0.5622.500 463V 3.625 1.812 3.375 0.5622.750 464V 4.000 1.937 3.500 0.6253.000 465V 4.250 2.062 3.875 0.625


Standard Materials of Construction:Faces: Carbon Graphite (Resin Impregnated.), Ceramic, Stainless Steel , Silicon Carbide, Tungsten CarbideElastomers: Buna, Viton, EPRMetallurgy: 304, 316, MonelPlease check with the factory for operating limits and conditions


Small Pump and Motor Seals

SHAFT SIZE

SIMILAR INDUSTRY

PART #

Crane Equivalent

Seal ODOperating


0.625 100 6 1.218 0.718 1.187 0.3430.750 101 6 1.343 0.718 1.437 0.4060.625 200 6 1.218 0.718 1.250 0.4060.750 201 6 1.343 0.718 1.375 0.406

0.625 113 6A 1.437 0.615 1.093 0.2180.750 606 6A 1.575 0.615 1.375 0.406

•Equivalent to John Crane Type 6, Pac-Seal Type 16, US Seal A head


Common Stocked Seals

•Single spring, elastomer bellows seal•Pre-assembled for easy installation•Common to many commercial and domestic pumps

Equivalent to John Crane Type 6A, Pac-Seal Type 68, US Seal B head

Standard Materials of Construction:Faces: Molded Plastic, Carbon Graphite (Resin Impregnated.), Ceramic, Stainless Steel , Silicon Carbide, Tungsten CarbideElastomers: Buna, Viton, EPRMetallurgy: 304, 316, Monel


Type 6Type 6 Type 6AType 6A


Type A8T, A9T

D D1 L D2 L1SHAFT SIZE

INCHESSeal OD

Operating Length

Seat Bore Thickness

0.750 1.190 0.937 1.375 0.4060.875 1.315 0.937 1.500 0.4061.000 1.440 1.000 1.625 0.4371.125 1.565 1.000 1.750 0.4371.250 1.690 1.000 1.875 0.4371.375 1.940 1.375 2.000 0.4371.500 1.940 1.125 2.125 0.4371.625 2.250 1.156 2.375 0.5001.750 2.315 1.375 2.500 0.5001.875 2.500 1.375 2.625 0.5002.000 2.625 1.375 2.750 0.5002.125 2.812 1.687 3.000 0.5622.250 2.843 1.375 3.125 0.5622.375 3.000 1.687 3.250 0.5622.500 3.125 1.375 3.375 0.5622.675 3.250 1.687 3.375 0.6252.750 3.375 1.687 3.500 0.6252.875 3.500 1.687 3.750 0.6253.000 3.625 1.687 3.875 0.625

D D2

L1

L

D1

A9T

A8T

Standard Materials of Construction:Faces: Carbon Graphite (Resin Impregnated.), Ceramic, Stainless Steel , Silicon Carbide, Tungsten CarbideElastomers: Buna, Viton, PTFE, EPR,Metallurgy: 304, 316, Monel



AMG-1

Other Common European Styles Available:ØAMG-12ØAMG- 13ØAMG-1S20ØAM3NØAM32ØAM37ØAM37GØAM2ØAH12NØAH17GNØAM7NØAM74ØAH75ØAH7NØAHJ92ØAHJ977GN

Standard Materials of Construction:Faces: Carbon Graphite (Resin Impregnated.), Silicon Carbide, Tungsten CarbideElastomers: Buna, Viton, EPRMetallurgy: 304, 316, Monel


•Single Seal•Common to many European Pumps•Single Spring •Bi Directional•Elastomeric Bellows•Equivalent to EagleBurgmann MG1 D D1 L

Shaft Seal mm

Seal ODOperating

Length

10 22.5 14.5

12 25.0 15.0

14 28.5 17.016 28.5 17.018 32.0 19.520 37.0 21.522 37.0 21.524 42.5 22.525 42.5 23.028 49.0 26.530 49.0 26.532 53.5 27.533 53.5 27.535 57.0 28.538 59.0 30.040 62.0 30.042 65.5 30.043 65.5 30.045 68.0 30.048 70.5 30.550 74.0 30.553 78.5 33.055 81.0 35.058 85.5 37.060 88.5 38.065 93.5 40.068 96.5 40.070 99.5 40.075 107.0 40.080 112.0 40.085 120.0 41.090 127.0 45.095 132.0 46.0100 137.0 47.0

DD1

Various Seat Styles and Dimensions on Following Pages


Seats

•All Styles and Materials of Construction•Custom Shapes•Repair and Lapping•Available with all standard elastomers

Cup Mount“O” Ring Groove

Materials of Construction:•Alumina Ceramic•Carbon•Phenolic•Tungsten Carbide•Reaction Bonded Silicon Carbide•Sintered Alpha Silicon Carbide•NiResist•17-4 PH•Glass Filled PTFE

D

D2

D D2 L1SHAFT SIZE

INCHESSeat Bore Thickness

0.625 1.250 0.4060.750 1.375 0.4060.875 1.500 0.4061.000 1.625 0.4371.125 1.750 0.4371.250 1.875 0.4371.375 2.000 0.4371.500 2.125 0.4371.625 2.375 0.5001.750 2.500 0.5001.875 2.625 0.5002.000 2.750 0.5002.125 3.000 0.5622.250 3.125 0.5622.375 3.250 0.5622.500 3.375 0.5622.625 3.375 0.6252.750 3.500 0.6252.875 3.750 0.6253.000 3.875 0.625

L1

Special sizes and designs readily available


D2

G50G50

Metric Seats

G60G60 G6G6G4G4 G9G9

L3 L1 L4 L1 L2

D D1 D2 D3 L1 L2 L3 L4Shaft Seal mm

Seat Bore OD

Seat Bore OD

Seat Bore OD

Bore Length

Bore Length

Bore Length

Bore Length

G6,G60, G9 G50 G4 G6, G60 G9 G50 G4

10 21.00 24.60 19.20 6.60 10.00 9.00 6.6012 23.00 27.80 21.60 6.60 10.00 9.00 5.60

14 25.00 30.95 24.60 6.60 10.00 10.50 5.6016 27.00 30.95 28.00 6.60 10.00 10.50 7.5018 33.00 34.15 30.00 7.50 11.50 10.50 8.0020 35.00 35.70 35.00 7.50 11.50 10.50 7.5022 37.00 37.30 35.00 7.50 11.50 10.50 7.5024 39.00 40.50 38.00 7.50 11.50 10.50 7.5025 40.00 40.50 38.00 7.50 11.50 10.50 7.5028 43.00 47.65 42.00 7.50 11.50 12.00 9.0030 45.00 50.80 45.00 7.50 11.50 12.00 10.5032 48.00 50.80 48.00 7.50 11.50 12.00 10.5033 48.00 54.00 50.00 7.50 11.50 12.00 11.0035 50.00 54.00 52.00 7.50 11.50 12.00 11.0038 56.00 57.15 55.00 9.00 14.00 12.00 10.3040 58.00 60.35 58.00 9.00 14.00 12.00 10.8042 61.00 63.50 60.00 9.00 14.00 12.00 12.0043 61.00 63.50 62.00 9.00 14.00 12.00 12.0045 63.00 63.50 64.00 9.00 14.00 12.00 11.6048 66.00 66.70 68.40 9.00 14.00 12.00 11.6050 70.00 69.85 69.30 9.50 15.00 13.50 11.6053 73.00 73.05 72.30 11.00 15.00 13.50 12.3055 75.00 76.20 75.40 11.00 15.00 13.50 13.3058 78.00 79.40 78.40 11.00 15.00 13.50 13.3060 80.00 79.40 80.40 11.00 15.00 13.50 13.3065 85.00 92.10 85.40 11.00 15.00 16.00 13.0068 90.00 95.25 91.50 11.30 18.00 16.00 13.7070 92.00 95.25 92.00 11.30 18.00 16.00 13.0075 97.00 101.60 99.00 11.30 18.00 16.00 14.0080 105.00 114.30 104.00 12.00 18.20 20.00 15.0085 110.00 117.50 109.00 14.00 18.20 20.00 14.8090 115.00 123.85 114.00 14.00 18.20 20.00 14.8095 120.00 127.00 120.30 14.00 17.20 20.00 15.80100 125.00 133.35 123.30 14.00 17.20 20.00 15.80

D1D1 D1D3

D


Seals for Unique Equipment

We pride ourselves on the ability to provide mechanical seals for equipment that is less common in the industrial market. Purchased from the OEM’s, these seals are typically quite expensive and can have long lead times. We are in a very good position to provide you with either a custom engineered seal for the application or a seal that is replicated to exact OEM dimensions and tolerances. Our customer’s savings and increased profits have been substantial.

The following is a few of the specialty pumps that we have manufactured seals for:ØRoto Jet ØGorman RuppØVikingØSeepexØFlygtØJohnson AlbinØBird ScreensØMission ØMoynoØACD CryogenicØEMU

We would be happy to work with you on any of your unusual seal requirements


Single and Double CartridgesSingle and Double Cartridges

Apex S1 Single Cartridge

Apex D2 Double Cartridge

Component SealsComponent Seals

Equivalents to Type 8’s, 9’s, RO’s, 880’s

Seal Repair of All BrandsSeal Repair of All Brands

Apex WBC Welded Bellows Cartridge

Welded Metal Bellows

Compression Compression PackingPacking

PTFE Bellows

Apex Sealing offers a diverse range of sealing products beyond the common shaft seals. We would be happy to get you a detailed brochure on these products as well.

Other Common Sealing Solutions


A.) Shaft / Sleeve Diameter ___________B.) Stuffing Box Bore I.D. _______________C.) Seat Bore in Gland ________________D.) Thickness of Stationary _____________E.) Working Length of the Seal _________F.) O.D. Of Seal _______________________G.) Gland Thickness __________________ _H.) Depth of Stuffing Box ______________

A.

B. C.

E.F.

G.H.

Product Description:Process Media: __________________________Abrasiveness: ___________________________Temperature: ___________________________pH Value: _______________________________% of Concentration:_____________________

Pressures:Stuffing Box Pressure: _____________________Suction Pressure: _________________________Discharge Pressure: ______________________

Equipment Description:Type of Equipment: ______________________Pump Manufacturer: _________________________________________Model: __________________________________Size: ____________________________________Shaft Speed: ____________________________Flush Available? _________________________

Previous Seal Used:Head Type: _____________________________Seat Type: ______________________________Seal Manufacturer: ______________________Seal Mnfr. Part #: ________________________Elastomer Used:__________________________Seal Face Combination: _________________

Application Data Sheet for Shaft Seals

D.

Notes / Sketch

Please copy and fax to (802) 524-7112

Documents

Shaft Seal Program - Apex Sealing Seal Program. Apex Sealing Inc., 164 B Yankee Park Road, Fairfax, VT, 05454, USA toll free 888.730.2739, ... •Equivalent to John Crane Type 1, Pac-Seal