Embed Size (px)
Citation preview
CABLE D-RING
SHADE SAIL HARDWARE
Technical DataCasting materialSurface treatmentBreaking load
Cable D-Ring are made from cast 316 grade stainless steel.
Product Code
cabledring5
cabledring8
cabledring10
Suits Wire (mm)
5
8
10
D (mm)
6
8
10
D1 (mm)
9
13
15
A (mm)
50
50
53
L (mm)
55
62
68
H (mm)
8
13
15
Breaking Load (kgs)
2,600
6,000
6,000
D - RINGTechnical DataForging materialSurface treatmentBreaking load
Product Code
Dring640
Dring850
Size (mm)
6*40
8*50
C (mm)
39
51
A (mm)
6
8
B (mm)
34
43
Breaking Load (kgs)
1,800
2,800
A
C
B
: Stainless Steel AISI304 - DIN 1.4301: “ E.P. ” (Electro polish): Standard safety factor for working load is 1/4 of “ T.D.L. ” (Tested deformation load)
: Stainless Steel AIS316 – DIN 1.4401: “ E.P. ” (Electro polish): Standard safety factor for working load is 1/4 of “T.D.L.” (Tested deformation load)
Field of ApplicationCable D-Ring are designed to support wire rope on shade steel corners.
Field of ApplicationD-rings are designed for assembly of shade sail corners using webbing. Rings are welded using the TIG Argon welding process.
TURNBUCKLE JAW AND JAWTechnical DataForging materialFrameSurface treatmentBreaking load
Product Code
Turnbuckjaw8
Turnbuckjaw10
Turnbuckjaw12
Size (mm)
8
10
12
L (mm)
160
200
245
L1 (mm)
105
125
150
M (mm)
M8
M10
M12
Breaking Load (kgs)
2,200
3,450
5,000
: Stainless Steel AISI316 - DIN 1.4401: Casting: “ E.P. ” (Electro polish): Standard safety factor for working load is 1/4 of “ T.D.L. ” (Tested deformation load)
Field of ApplicationJaw to jaw turnbuckles with nut provide an extra locking function after the �tttings are securely tightened.
Contact your dealer for more information.
POLYFAB MIDDLE EAST [email protected] +971 4 884 7933Fax +971 4 884 7934P.O. Box 450008, Dubai, UAE
THREADED FORK-ENDTechnical DataForging materialFrameSurface treatmentBreaking load
Product Code
Threaded fork 12
Threaded fork 16
M (mm)
M12
M16
L (mm)
265
285
L1 (mm)
225
225
B (mm)
12
16
Breaking Load (kgs)
5,000
8,000
SHACKLE KEYTechnical DataCasting materialSurface treatmentBreaking load
Product Code
shackey32100
L (mm)
100
C (mm)
32
: Stainless Steel AIS1316 - DIN 1.4401: “ E.P. ” (Electro polish): Standard safety factor for working load is 1/4 of “ T.D.L. ” (Tested deformation load)
Field of ApplicationShackle Key is used to tighten Turn Buckles and Nuts during installation.
CARE & MAINTENANCE PROGRAMThe common rule for keeping stainless steel in its original, pristine condition is to “clean it when it’s dirty”. For regular cleaning start with a soft cloth and clean warm water or use ordinary soap or a mild, dilluted detergent or dilluted amonia in warm water; apply with a soft cloth or synthetic sponge. Rinse well, dry with a soft cloth or drip dry.
Occasionally the use of mild household cleaner, a �ne synthetic scourer or a brush with nylon bristles may be used. Regular cleaning will often remove heavy soiling and accumulated staining.
Routine, simple and gentle cleaning
Use only the above mentioned cleaning products
Employ repeated routine cleaning rather than an aggressive single one
SUGGESTIONS:
Do not use coarse abrasive powders
Do not use metallic scourers
Do not use “Silver cleaners”
Do not subject stainles steel to “abnormal” use
WHAT NOT TO DO:
Technical DataForging materialFrameSurface treatmentBreaking load
Note: Standard safety factor for working load is 1/4 of breaking load.
: Stainless Steel AISI316 – DIN 1.4401: Casting: “E.P.” (Electro polish): Standard safety factor for working load is 1/4 of “T.D.L.” (Tested deformation load)
Field of ApplicationThreaded fork-ends are used for tensioning shade sail ends with additional bene�t of 180º toggle head for ease of installation.
