If you can't read please download the document
Upload
dothu
View
226
Download
2
Embed Size (px)
Citation preview
SERVICE MANUAL
DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYER
MODEL DVD-1930CI
DVD-757
TOKYO, JAPANDenon Brand Company, D&M Holdings Inc.
X0306V.02 DE/CDM 0609
Some illustrations using in this service manual areslightly different from the actual set.
Please use this service manual with referring to theoperating instructions without fail.
For purposes of improvement, specifications anddesign are subject to change without notice.
8
For U.S.A. & Canada model
Please refer to theMODIFICATION NOTICE.
Ver. 2
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
2
DVD-1930CI / DVD-757
Please heed the points listed below during servicing and inspection.
Heed the cautions!Spots requiring particular attention when servicing, such asthe cabinet, parts, chassis, etc., have cautions indicated onlabels or seals. Be sure to heed these cautions and the cau-tions indicated in the handling instructions.
Caution concerning electric shock!(1) An AC voltage is impressed on this set, so touching inter-
nal metal parts when the set is energized could causeelectric shock. Take care to avoid electric shock, by for ex-ample using an isolating transformer and gloves whenservicing while the set is energized, unplugging the powercord when replacing parts, etc.
(2)There are high voltage parts inside. Handle with extra carewhen the set is energized.
Caution concerning disassembly and assembly!Though great care is taken when manufacturing parts fromsheet metal, there may in some rare cases be burrs on theedges of parts which could cause injury if fingers are movedacross them. Use gloves to protect your hands.
Only use designated parts!The set's parts have specific safety properties (fire resis-tance, voltage resistance, etc.). For replacement parts, besure to use parts which have the same properties. In particu-lar, for the important safety parts that are marked ! on wiringdiagrams and parts lists, be sure to use the designated parts.
Be sure to mount parts and arrange thewires as they were originally!
For safety reasons, some parts use tape, tubes or other insu-lating materials, and some parts are mounted away from thesurface of printed circuit boards. Care is also taken with thepositions of the wires inside and clamps are used to keepwires away from heating and high voltage parts, so be sure toset everything back as it was originally.
Inspect for safety after servicing!Check that all screws, parts and wires removed or discon-nected for servicing have been put back in their original posi-tions, inspect that no parts around the area that has beenserviced have been negatively affected, conduct an insulationcheck on the external metal connectors and between theblades of the power plug, and otherwise check that safety isensured.
(Insulation check procedure)Unplug the power cord from the power outlet, disconnect theantenna, plugs, etc., and turn the power switch on. Using a500V insulation resistance tester, check that the insulation re-sistance between the terminals of the power plug and the ex-ternally exposed metal parts (antenna terminal, headphonesterminal, microphone terminal, input terminal, etc.) is 1M orgreater. If it is less, the set must be inspected and repaired.
Concerning important safety parts
Many of the electric and structural parts used in the set havespecial safety properties. In most cases these properties aredifficult to distinguish by sight, and using replacement partswith higher ratings (rated power and withstand voltage) doesnot necessarily guarantee that safety performance will be pre-served. Parts with safety properties are indicated as shownbelow on the wiring diagrams and parts lists is this servicemanual. Be sure to replace them with parts with the designat-ed part number.
(1) Schematic diagrams ... Indicated by the ! mark.
(2) Parts lists ... Indicated by the ! mark.
Using parts other than the designated partscould result in electric shock, fires or otherdangerous situations.
SAFETY PRECAUTIONSThe following check should be performed for the continued protection of the customer and service technician.
LEAKAGE CURRENT CHECKBefore returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassisresistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the powercord is less than 460 kohms, the unit is defective.
LASER RADIATIONDo not stare into beam or view directly with optical instruments, class 3A laser product.
CAUTION
CAUTION
(1)
(2)
!
500V M
(1) !
(2) !
w w w . x i a o y u 1 6 3 . c o m
Q Q 3 7 6 3 1 5 1 5 0 992894298
T E L 1 3 9 4 2 2 9 6 5 1 3 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
3
DVD-1930CI / DVD-757
SPECIFICATIONS
Notes:
1. All Items are measured without pre-emphasis unless otherwise specified.
2. Power supply: AC 120 V, 60 Hz
3. Load Impedance: 100 k load (Audio Output)4. Room Ambient: +25 C
Item Conditions Unit Nominal Limit
1. Video Output 75 load Vpp 1.0 0.1
2. Coaxial Digital Out 75 load mVpp 500 50
3. Audio (PCM)
3-1. Output Level 1 kHz, 0 dB Vrms 2.0
3-2. S/N dB 115
3-3. Freq. Response
DVD fs = 48 kHz, 20 Hz ~ 22 kHz dB 1.0
CD fs = 44.1 kHz, 20 Hz ~ 20 kHz dB 1.0
3-4. THD+N
DVD 1 kHz, 0 dB % 0.004
CD 1 kHz, 0 dB % 0.004
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
4
DVD-1930CI / DVD-757
Safety Check after ServicingExamine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts, and wires have been returned to their original positions. Afterwards, do the following tests and confirm the specified values to verify compliance with safety standards.
1. Clearance Distance
When replacing primary circuit components, confirm specified clearance distance (d) and (d) between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1)
Table 1: Ratings for selected area
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
2. Leakage Current Test
Confirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below.
Measuring Method (Power ON):
Insert load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across the terminals of load Z. See Fig. 2 and the following table.
Table 2: Leakage current ratings for selected areas
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
AC Line Voltage Clearance Distance (d), (d)
120 V 3.2 mm (0.126 inches)
AC Line Voltage Load Z Leakage Current (i) Earth Ground (B) to:
120 V 0.15 F CAP. & 1.5 k RES. Connected in parallel i 0.5 mA Peak Exposed accessible parts
Chassis or Secondary Conductor
Primary Circuit
Fig. 1
d' d
AC Voltmeter (High Impedance)
Exposed Accessible Part
B Earth Ground Power Cord Plug Prongs
Z
Fig. 2
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
5
DVD-1930CI / DVD-757
STANDARD NOTES FOR SERVICING
Circuit Board Indications1. The output pin of the 3 pin Regulator ICs is
indicated as shown.
2. For other ICs, pin 1 and every fifth pin are indicated as shown.
3. The 1st pin of every male connector is indicated as shown.
Instructions for Connectors1. When you connect or disconnect the FFC (Flexible
Foil Connector) cable, be sure to first disconnect the AC cord.
2. FFC (Flexible Foil Connector) cable should be inserted parallel into the connector, not at an angle.
Pb (Lead) Free SolderWhen soldering, be sure to use the Pb free solder.
How to Remove / Install Flat Pack-IC
1. Removal
With Hot-Air Flat Pack-IC Desoldering Machine:
1. Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1)
2. Remove the flat pack-IC with tweezers while applying the hot air.
3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
CAUTION:
1. The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC.
2. Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape around the flat pack-IC to protect other parts from damage. (Fig. S-1-2)
Top View
Out In
Bottom ViewInput
5
10
Pin 1
Pin 1
FFC Cable
Connector
CBA
* Be careful to avoid a short circuit.
Fig. S-1-1
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
6
DVD-1930CI / DVD-757
3. The flat pack-IC on the CBA is affixed with glue, so be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it.
With Soldering Iron:
1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)
2. Lift each lead of the flat pack-IC upward one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air desoldering machine. (Fig. S-1-4)
3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
Hot-airFlat Pack-ICDesolderingMachine
CBA
Flat Pack-IC
Tweezers
MaskingTape
Fig. S-1-2
Flat Pack-IC Desoldering Braid
Soldering Iron
Fig. S-1-3
Fine TipSoldering Iron
SharpPin
Fig. S-1-4
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
7
DVD-1930CI / DVD-757
With Iron Wire:
1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)
2. Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5.
3. While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5.
4. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
5. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied.
2. Installation1. Using desoldering braid, remove the solder from
the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily.
2. The mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the 1 on the PCB when positioning for installation. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.)
3. Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges.
To Solid Mounting Point
Soldering Iron
Iron Wire
or
Hot Air Blower
Fig. S-1-5
Fine TipSoldering IronCBA
Flat Pack-ICTweezers
Fig. S-1-6
Example :
Pin 1 of the Flat Pack-ICis indicated by a " " mark. Fig. S-1-7
Presolder
CBA
Flat Pack-IC
Fig. S-1-8
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
8
DVD-1930CI / DVD-757
Instructions for Handling Semi-conductorsElectrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work.
1. Ground for Human Body
Be sure to wear a grounding band (1 M) that is properly grounded to remove any static electricity that may be charged on the body.
2. Ground for Workbench
Be sure to place a conductive sheet or copper plate with proper grounding (1 M) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing.
CBA
Grounding Band
Conductive Sheet orCopper Plate
1M
1M
CBA
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
9
DVD-1930CI / DVD-757
CABINET DISASSEMBLY INSTRUCTIONS
1. Disassembly FlowchartThis flowchart indicates the disassembly steps to gainaccess to item(s) to be serviced. When reassembling,follow the steps in reverse order. Bend, route, anddress the cables as they were originally.
2. Disassembly MethodNote:
(1) Identification (location) No. of parts in the figures
(2) Name of the part
(3) Figure Number for reference
(4) Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered. P = Spring, L = Locking Tab, S = Screw, CN = Connector* = Unhook, Unlock, Release, Unplug, or Desoldere.g. 2(S-2) = two Screws (S-2), 2(L-2) = two Locking Tabs (L-2)
(5) Refer to Reference Notes.
About tightening screws
When tightening screws, tighten them with the following torque.
ID/Loc. No.
Part
Removal
Fig.No.
Remove/*Unhook/Unlock/Release/Unplug/Desolder
Note
[1] Top Cover D1 5(S-1) ---
[2] Front Unit D2 *4(L-1), *2(L-2), *3(L-3), *CN2001 1
[3] Tray Panel D2 *2(L-4) 1
[4] Function CBA D3 6(S-2) ---
[5] Front Assembly D3 ---------- ---
[6] Reinforce Plate D4 2(S-3) ---
[7] Rear Panel D4 8(S-4), (S-5), (S-6),2(S-7) 4
[8] DVD Main CBA Unit D5
3(S-8), *CN201, *CN301, *CN401, *CN601, *CNS01, *CNF02
24
[9] Interface CBA D6 (S-9) ---
[1] Top Cover
[5] Front Assembly
[2] Front Unit
[3] Tray Panel
[6] Reinforce Plate
[7] Rear Panel
[16] Loader Base
[18] Main PCB Holder
[8] DVD Main CBA Unit
[13] DVD Mechanism
[17] Power PCB Holder
[14] LED CBA
[4] Function CBA
[11] 5.1ch Amp CBA
[12] Jack PCB Holder
[9] Interface CBA
[10] D Sub Holder
[15] AV CBA
[10] D Sub Holder D6 (S-10) ---
[11] 5.1ch Amp CBA D6(S-11), 2(L-5), *CN7101 ---
[12] Jack PCB Holder D6 2(S-12) ---
[13] DVD MechanismD5D7 4(S-13)
23
[14] LED CBA D8 *CN2102 ---
[15] AV CBA D8 4(S-14), (S-15) ---
[16] Loader Base D9 4(S-16) ---
[17] Power PCB Holder D9 2(S-17) ---
[18] Main PCB Holder D9 (S-18) ---
(1)
(2)
(3)
(4)
(5)
Screws Torque
(S-1), (S-2), (S-3), (S-4), (S-5), (S-6), (S-7), (S-8), (S-9), (S-10), (S-11), (S-12), (S-13), (S-14),(S-15), (S-16), (S-17),(S-18)
0.45 0.05 Nm
ID/Loc. No.
Part
Removal
Fig.No.
Remove/*Unhook/Unlock/Release/Unplug/Desolder
Note
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
10
DVD-1930CI / DVD-757
Reference Notes1. CAUTION 1: Locking Tabs (L-1), (L-2), (L-3) and
(L-4) are fragile. Be careful not to break them.
1) Release four Locking Tabs (L-1), then release two Locking Tabs (L-2).
2) Release three Locking Tabs (L-3).
3) Disconnect connector CN2001, then remove the Front Unit.
2. CAUTION 2: Electrostatic breakdown of the laser diode in the optical system block may occur as a potential difference caused by electrostatic charge accumulated on cloth, human body etc., during unpacking or repair work.To avoid damage of pickup follow next procedures.
1) Short the three short lands of FPC cable with solder before removing the FFC cable (CN201) from it. If you disconnect the FFC cable (CN201), the laser diode of pickup will be destroyed. (Fig. D5)
2) Disconnect Connectors (CN301), (CN401) and (CN601). Remove three screws (S-8) and lift the DVD Main CBA Unit. (Fig. D5)
3. CAUTION 3: When reassembling, confirm the FFC cable (CN201) is connected completely. Then remove the solder from the three short lands of FPC cable. (Fig. D5)
4. CAUTION 4: When installing the DVD Main CBA Unit with a screw, hold and press the DVD Main CBA Unit to align the HDMI connector with the connectors hole for HDMI on the Rear Panel.
Fig. D1
[1] Top Cover (S-1)
(S-1)
(S-1)
[2] Front Unit
[3] Tray Panel
CN2001
(L-1)
(L-1)
(L-2)
(L-2)
(L-4)(L-4)
(L-3)
Fig. D2
[4] Function CBA
[5] Front Assembly
(S-2)
(S-2)
Fig. D3
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
11
DVD-1930CI / DVD-757
[7] Rear Panel(S-6)
(S-4)
(S-4)
(S-5)
(S-4)
Fig. D4
(S-7)[6] Reinforce Plate
(S-3)
(S-3)
(S-8)(S-8)
[8] DVD Main CBA Unit
CN401
CN301
A
Fig. D5
CNF02
CN201
CN601
(S-8)
CNS01
Short the three short lands by soldering.(Either of two places.)
View for AFPC Cable
(S-11)
(S-12)[12] JackPCB Holder
[11] 5.1ch Amp CBA
(L-5)
Fig. D6
[9] InterfaceCBA
[10] D SubHolder
(S-9)
(S-10)
CN7101
Fig. D7
[13] DVD Mechanism
(S-13)
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
12
DVD-1930CI / DVD-757
3. How to Eject Manually1. Remove the Top Cover.
2. Rotate the roulette in the direction of the arrow as shown below.
[15] AV CBA
[14] LED CBA
(S-14)
(S-14)
(S-15)
CN2102
Fig. D8
[16] Loader Base
[18] Main PCBHolder
(S-16)
Fig. D9
(S-16)
(S-18)
[17] Power PCB Holder
(S-17)
A
View for A
Rotate this roulette in the direction of the arrow
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
13
DVD-1930CI / DVD-757
HOW TO INITIALIZE THE DVD PLAYER
To put the program back at the factory-default, initialize the DVD player as the following procedure.
1. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order. Fig. a appears on the screen.
2. Press [CLEAR] button on the remote control unit. Fig. b appears on the screen.
When OK appears on the screen, the factory default will be set.
3. To exit this mode, press [POWER OFF] button.
MODEL : *******Version : *.**Region : *
EXIT: POWEREEPROM CLEAR : CLEAR
Fig. a
"*******" differs depending on the models.
MODEL : *******Version : *.**Region : *
EEPROM CLEAR : OK
EXIT: POWEREEPROM CLEAR : CLEAR
"*******" differs depending on the models.
Fig. b
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
14
DVD-1930CI / DVD-757
FIRMWARE RENEWAL MODE
1. Turn the power on and remove the disc on the tray.
2. To put the DVD player into version up mode, press [9], [8], [7], [6], and [SEARCH MODE] buttons on the remote control unit in that order. The tray will open automatically. Fig. a appears on the screen and Fig. b appears on the VFD.
The DVD player can also enter the version up mode with the tray open. In this case, Fig. a will be shown on the screen while the tray is open.
3. Load the disc for version up.
4. The DVD player enters the F/W version up mode automatically. Fig. c appears on the screen and Fig. d appears on the VFD. If you enter the F/W for different models, Disc Error will appear on the screen, then the tray will open automatically.
The appearance shown in (*1) of Fig. c is described as follows:
5. After programming is finished, the tray opens automatically. Fig. e appears on the screen and the checksum in (*2) of Fig. e appears on the VFD (Fig. f).
At this time, no button is available.
6. Remove the disc on the tray.
7. Unplug the AC cord from the AC outlet. Then plug it again.
8. Turn the power on by pressing the [POWER ON] button and the tray will close.
9. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order. Fig. g appears on the screen.
F/W Version Up Mode Model No : *******VERSION : *.**
Please insert a DISCfor F/W Version Up.
EXIT: POWER
"*******" differs depending on the models.
Fig. a Version Up Mode Screen
Fig. b VFD in Version Up Mode
VERSION : ************.ab7Reading...
F/W Version Up Mode Model No : *******VERSION : *.**
Fig. c Programming Mode Screen
"*******" differs depending on the models.
(*1)
Fig. d VFD in Programming Mode (Example)
No. Appearance State
1 Reading... Sending files into the memory
2 Erasing... Erasing previous version data
3 Programming... Writing new version data
VERSION : ************.ab7CompletedSUM : 7ABC
F/W Version Up Mode Model No : *******VERSION : *.**
"*******" differs depending on the models.
Fig. e Completed Program Mode Screen
(*2)
Fig. f VFD upon Finishing the Programming Mode (Example)
MODEL : *******Version : *.**Region : *
EXIT: POWEREEPROM CLEAR : CLEAR
Fig. g
"*******" differs depending on the models.
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
15
DVD-1930CI / DVD-757
10. Press [CLEAR] button on the remote control unit. Fig. h appears on the screen.
When OK appears on the screen, the factory default will be set. Then the firmware renewal mode is complete.
11. To exit this mode, press [POWER OFF] button.
MODEL : *******Version : *.**Region : *
EEPROM CLEAR : OK
EXIT: POWEREEPROM CLEAR : CLEAR
"*******" differs depending on the models.
Fig. h
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
16
DVD-1930CI / DVD-757
TROUBLESHOOTING
FLOW CHART NO.2The fuse blows out.
After servicing, replace the fuse.
Check the presence that the primary componentis leaking or shorted and service it if defective.
Check the presence that the rectifying diode orcircuit is shorted in each rectifying circuit of secondary side, and service it if defective.
FLOW CHART NO.3When the output voltage fluctuates.
Yes
No
FLOW CHART NO.4When buzz sound can be heard in the vicinity of power circuit.
Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side, and service it if defective. (D1003, D1006, D1008, D1016, D1030, IC1002, Q1002, Q1004, Q1005, Q1011, Q1014)
Does the photo coupler circuit on the secondary side operate normally?
Check IC1001, D1012, D1024 and their periphery, and service it if defective.
Check IC1001, IC1006 and their periphery, and service it if defective.
FLOW CHART NO.5-FL is not outputted.
Is approximately -23V voltage supplied to the anode of D1003?
Check D1003 and periphery circuit, and service it if defective.
Check if there is any leak or short-circuit on the loaded circuit, and service it if defective.
Yes
No
FLOW CHART NO.1
The power cannot be turned on.
Is the fuse normal?
Is normal state restored when once unplugged power cord is plugged again after several seconds?
Is the EV +3.3V line voltage normal?
See FLOW CHART No.2
Check if there is any leak or short-circuiting on the primary circuit component, and service it if defective. (Q1001, Q1003, Q1008, T1001, D1001, D1002, D1004, D1005, D1011, C1003, C1005)
Check each rectifying circuit of the secondary circuitand service it if defective.
Yes
Yes
Yes
No
No
No
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
17
DVD-1930CI / DVD-757
FLOW CHART NO.7
P-ON+5V is not outputted. (EV+10V is outputted normally.)
Is the "H" signal inputted into the base of Q1004?
Replace Q1004.
Replace Q1014.
Check R1068 and D1046, and service it if defective.Yes
No
Is the "H" signal inputted into the base of Q1014? Check D1047, R1069, R1098 and the periphery circuit, and service it if defective.
No
FLOW CHART NO.8P-ON+3.3V is not outputted. (P-ON+10V is outputted normally.)
Is 3.3V voltage supplied to the collector of Q1011?
Replace Q1011 or R1066 or R1067.
Check D1008, C1007, C1038, L1007, and the periphery circuit, and service it if defective.Yes
No
FLOW CHART NO.9EV+5V is not outputted.
Is EV+10V outputted normally? Refer to "FLOW CHART NO.6"
Yes
Yes
No
FLOW CHART NO.10EV+1.2V is not outputted.
Is 2.5V voltage supplied to Pin(3) of IC1002?
Replace IC1002.
Check D1006, C1014, L1008 and the periphery circuit, and service it if defective.
Yes
No
FLOW CHART NO.6P-ON+10V (EV+10V) is not outputted.
Is 10V voltage supplied to the emitter of Q1002?
Is the voltage of base on Q1002 lower than thevoltage of emitter on Q1002 when turning the power on?
Replace Q1002.
Check D1030, D1048, C1035, C1048, L1009, and the periphery circuit, and service it if defective.
Check Q1016 and PWRCON line and service it if defective.
Yes
Yes
No
No
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
18
DVD-1930CI / DVD-757
YesNo
FLOW CHART NO.12The key operation is not functioning.
Are the contact point and the installation state of the key switches (SW2101, SW2103-2108, SW2181-2183) normal?
When pressing each switches (SW2101, SW2103-2108, SW2181-2183), do the voltage of each pin of IC2001 (shown below) increase?SW2103, 2104, 2106, 2107, 2182: IC2001 3PINSW2101, 2105, 2108, 2181, 2183: IC2001 4PIN
Check the switches (SW2101, SW2103-2108, SW2181-2183) and their periphery, and service it if detective.
No Re-install the switches (SW2101, SW2103-2108, SW2181-2183) correctly or replace the poor switch.
Replace IC2001.Yes
FLOW CHART NO.13No operation is possible from the remote control unit.
Operation is possible from the DVD, but nooperation is possible from the remote control unit.
Replace the infrared remote control receiver (RM2001)or replace the remote control unit.
Check the line between Pin(1) terminal of receiver (RM2001) and Pin(26) of CN1001, and service it if defective.
Is the "L" pulse sent out Pin(1) terminal of receiver(RM2001) when the infrared remote control is activated?
Is the "L" pulse supplied to the Pin(26) of CN1001?
Replace DVD Main CBA Unit.
Is 5V voltage supplied to Pin(3) terminal ofthe infrared remote control receiver (RM2001)?
YesNo
Check EV+5V line and service it if defective.No
No
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
FLOW CHART NO.11The fluorescent display tube does not light up.
Is 3.3V voltage supplied to Pins(6,24) of IC2001?
Is the voltage of approximately -20V supplied to Pin(15) of IC2001?
Is there 500kHz oscillation at Pin(26) of IC2001?
Are the filament voltage supplied between Pins(1, 2) and Pins(29, 30) of the fluorescent display tube? And the negative voltage applied between these pins and GND?
Replace the fluorescent display tube.
Check the EV+3.3V line and service it if defective.
Check the -FL (-20V) line and service it if defective.
Check R2002, IC2001 and their periphery, and service it if defective.
Check PWRCON line, and service it if defective.
Is the "H" signal inputted to base of Q1016?
Check D1016, D1017, T1001, and their periphery, and service it if defective.
Is -14V voltage supplied to collector of Q1005?
No
Yes
YesNo
Check Q1015, Q1016, D1055, and their periphery, and service it if defective.
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
19
DVD-1930CI / DVD-757
FLOW CHART NO.17[No Disc] indicated. (When the focus servo is not functioning.)
FLOW CHART NO.18[No Disc] indicated. (When the laser beam does not light up.)
Replace the DVD Main CBA Unit.
Replace the DVD Mechanism.
No
Yes
Replace the DVD Main CBA Unit.
Replace the DVD Mechanism.
No
Yes
No improvement can be found. Original DVD Main CBA Unit is poor.
No improvement can be found. Original DVD Main CBA Unit is poor.
FLOW CHART NO.16[No Disc] indicated. (When the focus error occurs.)
Replace the DVD Main CBA Unit.
No improvement can be found. Original DVD Main CBA Unit is poor.
Replace the DVD Mechanism.
No
Yes
Yes
FLOW CHART NO.15The disc tray cannot be opened and closed.
Replace the DVD Main CBA Unit.
Original DVD Main CBA Unit is poor.
Replace the DVD Mechanism.
No improvement can be found.No
Yes
FLOW CHART NO.14The disc tray cannot be opened and closed. (It can be done using the remote control unit.)
Is the normal control voltage inputted to Pin(4) of IC2001? Refer to "FLOW CHART NO.12"
Refer to "FLOW CHART NO.15"
Replace the "OPEN/CLOSE" button (SW2108).No
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
20
DVD-1930CI / DVD-757
Is 5V voltage applied to the Pin(4, 12) of IC1402 and Pin(4) of IC1403?
Replace IC1402 or IC1403.
Check P-ON+5V line andservice it if detective.
Are the video signals outputted to each pin of IC1402 or IC1403?
Yes No
Yes
Yes
NoIC1402 13PIN S-Y(I/P)IC1402 11PIN Pb/CbIC1402 10PIN Pr/CrIC1403 5PIN S-Y(I)IC1403 6PIN CVBSIC1403 7PIN S-C
Check the periphery of JK1404 from Pins (10, 11, 13) of IC1402 and service it if detective.
Check the periphery of JK1404 from Pin(6) of IC1403 and service it if detective.
Check the periphery of JK1401 from Pin (5) of IC1403 and service it if detective.
Check the periphery of JK1401 from Pin (7) of IC1403 and service it if detective.
Are the video signals outputted to the specific output terminal?
Are the component video signals outputted to the VIDEO OUT terminal (JK1404)?
Are the luminance signals outputted to the S-OUT terminal (JK1401)?
Are the chroma signals outputted to the S-OUT terminal (JK1401)?
No
No
No
NoAre the composite video signals outputted to the VIDEO OUT terminal (JK1404)?
FLOW CHART NO.20Picture does not appear normally.
Set the disc on the disc tray, and playback.
Are the video signals outputted to each pin of CN1601 on the AV CBA?
Replace the DVD Main CBA Unit or DVD Mechanism.
Check the line between each pin of CN1601 and each pin of IC1402 or IC1403 on the AV CBA, and service it if detective.
CN1601 2PIN IC1403 3PIN S-Y(I)CN1601 10PIN IC1403 1PIN S-CCN1601 8PIN IC1402 3PIN S-Y(I/P)CN1601 6PIN IC1402 6PIN Pb/CbCN1601 4PIN IC1402 8PIN Pr/Cr
Are the video signals shown above inputted into each pin of IC1402 or IC1403?
Yes
No
No
CN1601 2PIN S-Y(I)CN1601 4PIN Pr/CrCN1601 6PIN Pb/CbCN1601 8PIN S-Y(I/P)CN1601 10PIN S-C
IC1403 3PIN S-Y(I)IC1403 1PIN S-CIC1402 3PIN S-Y(I/P)IC1402 6PIN Pb/CbIC1402 8PIN Pr/Cr
FLOW CHART NO.19Both functions of picture and sound do not operate normally.
Replace the DVD Main CBA Unit.
Replace the DVD Mechanism.
No
YesNo improvement can be found. Original DVD Main CBA Unit is poor.
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
21
DVD-1930CI / DVD-757
FLOW CHART NO.21
Audio is not outputted normally.
Set the disc on the disc tray, and playback.
Are the analog audio signals outputted to each pin of CN1601 on AV CBA?
Is the "H" level mute signal outputted to CN1601 on AV CBA ?
CN1601 12PIN AUDIO(L)CN1601 14PIN AUDIO(R)
CN1601 13PIN AUDIO(L)-MUTECN1601 19PIN AUDIO(R)-MUTE
IC1201 1PIN AUDIO(L)IC1201 7PIN AUDIO(R)
IC1201 2PIN AUDIO(L)IC1201 6PIN AUDIO(R)
Replace the DVD Main CBA Unit or DVD Mechanism.
Replace the DVD Main CBA Unit or DVD Mechanism.
Replace IC1201.
Check the periphery between Pins(1,7) of IC1201 and JK1201, and service it if detective.
Check each line between each pin of CN1601 and each pin of IC1201 on AV CBA, and service it if detective.
CN1601 12PIN IC1201 2PIN AUDIO(L)CN1601 14PIN IC1201 6PIN AUDIO(R)
Are the analog audio signals inputted to each pin of IC1201.
Are the analog audio signals outputted to each pin of IC1201?
Are the audio signals outputted to the specific output terminal?
Are the audio signals outputted to the audioterminal (JK1201)?
Yes
Yes
Yes
Yes
No
No
No
No
No
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
22
DVD-1930CI / DVD-757
FLOW CHART NO.22
Audio is not outputted. (JK7101)
Set the disc (with 5.1ch Audio) on the disc tray, and playback.
Are the analog audio signals outputted to each pin of CN7102 on 5.1ch Amp CBA.
CN7102 15PIN FRONT(L)CN7102 13PIN FRONT(R)CN7102 11PIN SURROUND(L)CN7102 9PIN SURROUND(R)CN7102 7PIN CENTERCN7102 5PIN SUBWOOFER
IC7301 2, 6PIN FRONT(L/R)IC7401 2, 6PIN SURROUND(L/R)IC7501 2, 6PIN CENTER/SUBWOOFER
Replace the DVD Main CBA or DVD Mechanism.
Replace ICs (IC7301, IC7401 or IC7501).
Check each line between each pin of CN7102 and each pin of IC7301,IC7401 and IC7501 and service it if defective.
CN7102 15,13PIN IC7301 2,6PIN FRONT(L/R)CN7102 11,9PIN IC7401 2,6PIN SURROUND(L/R)CN7102 7,5PIN IC7501 2,6PIN CENTER/SUBWOOFER
Are the analog audio signals inputted to each pin of IC7301, IC7401 and IC7501.
Are the analog audio signals outputted to each pin of IC7301, IC7401 and IC7501.
IC7301 1,7PIN FRONT(L/R)IC7401 1,7PIN SURROUND(L/R)IC7501 1,7PIN CENTER/SUBWOOFER
Yes
Yes
No
No
No
Check each line and service it if defective.No
Replace the DVD Main CBA Unit.No
Yes
Do the mute signals of CN7102 on 5.1ch Amp CBA become to "H" level?
FRONT(L) CN7102 14PINFRONT(R) CN7102 12PINSURROUND(L) CN7102 10PINSURROUND(R) CN7102 8PINCENTER CN7102 6PINSUBWOOFER CN7102 4PIN
Yes
Is the analog audio signal of each line outputted to each terminal of JK7101 (as shown below) ?
IC7301 1PIN JK7101 FRONT(L) IC7301 7PIN JK7101 FRONT(R)IC7401 1PIN JK7101 SURROUND(L)IC7401 7PIN JK7101 SURROUND(R)IC7501 1PIN JK7101 CENTER IC7501 7PIN JK7101 SUBWOOFER
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
23
DVD-1930CI / DVD-757
BLOCK DIAGRAMSSystem Control / Servo Block Diagram
CN
401
CN
1001
127 8 9 10 11
RE
MO
TE
SE
NS
OR
RM
2001
JK35
01
1G 7G~
23 17
~
a/K
EY-
1b/
KE
Y-2
c/K
EY-
3d/
KE
Y-4 e
K1
K2
GR
IDF
IP
SE
GM
EN
T
FL2
001
IC20
01(F
RO
NT
PA
NE
L C
ON
TR
OL)
13 14 16 34
f/KE
Y-6 g h i
KE
YM
ATR
IX
CN
2001
CN
2101
KE
Y-1
66
KE
Y-2
44
KE
Y-3
55
KE
Y-4
77
Q20
86
K2
22
K1
33
KE
Y-6
11
RE
MO
CO
N-I
N
RE
MO
CO
N-O
UT
74F
P-D
IN22
28F
P-D
INF
P-D
IN23
12F
P-S
TB
242
FP
-ST
BF
P-S
TB
25
73F
P-D
OU
T21
27F
P-D
OU
TF
P-D
OU
T22
75F
P-C
LK23
1F
P-C
LKF
P-C
LK24
72R
EM
OT
E25
RE
MO
TE
26
253
HD
MI
26H
DM
I27
AV
CB
A
FU
NC
TIO
N C
BA
IC35
10
71
AM
P
SW
2101
PO
WE
R
CN
2002
CN
2102
D21
82
PO
WE
R-L
ED
22
STAN
DBY
-LED
33
KE
Y-2
55
K2
66
LE
D C
BA
PO
WE
R
STA
ND
BY
INV
-PO
WC
ON
+5V
TO P
OW
ER
SU
PP
LYB
LOC
KD
IAG
RA
M
Q20
88
Q20
89
HD
MI-
LED
77
+5V
D21
84H
DM
I
IC30
1(S
ER
VO
DR
IVE
)
CN
301
M
SLE
DM
OT
OR
M
SP
IND
LEM
OT
OR
IC10
1(M
ICR
O C
ON
TR
OLL
ER
)
+ -+ -
+ -+ -
+ -+ - + -
SLE
DM
OTO
RD
RIV
E
FO
CU
SA
CT
UAT
OR
DR
IVE
SP
IND
LEM
OTO
RD
RIV
E
TR
AC
KIN
GA
CT
UAT
OR
DR
IVE
144
TR
AY-I
N
SLD
91
SP
DL
90
TR
AC
KIN
GD
RIV
E
145
FO
CU
S D
RIV
E
89
FS
(+)
FS
(-)
TS
(+)
TS
(-)
77A
DA
C-M
D
78A
DA
C-M
C79
AD
AC
-ML
AD
AC
-MC
AD
AC
-ML
M-M
UT
E
254
AU
DIO
-MU
TE
AD
AC
-MD
AU
DIO
-MU
TE
256
M-M
UT
E
RS
232C
-TX
RS
232C
-RX
TR
AY-I
N
1S
P(+
)2
SP
(-)
6T
RA
Y-I
N3
GN
D4
SL(
-)5
SL(
+)
VR
EF
RE
SE
T84
RE
SE
T
IC46
1
21
+3.
3V
IC20
2(O
P A
MP
)
15 16 14 13 12 11 17 182364 531 225 2427 26
87S
L-A
MP
139
SP
-RO
T
+3.
3V
12 6
753 13
1412
142
FD
-OF
ST
141
TD
-OF
ST
DR
IVE
CB
A
DV
D M
AIN
CB
A U
NIT
TO D
IGIT
AL
SIG
NA
L P
RO
CE
SS
BLO
CK
D
IAG
RA
M
TO A
UD
IOB
LOC
K D
IAG
RA
M
AD
AC
-MD
AD
AC
-MC
TO S
AC
DB
LOC
K D
IAG
RA
M
(AM
P)
140
SL-
AD
S
RE
SE
T
IC46
2
13
+3.
3V 1
14 1311 12
IC23
21(R
S23
2C I/
F)
2 3
JK23
21
TX
44
RX
22
CN
2321
CN
F02
INT
ER
FAC
E C
BA
71 70R
S23
2C-
CO
NN
EC
TO
R 1
NO
TE
: E
ither
IC46
1 or
IC46
2 is
use
d fo
r D
VD
MA
IN C
BA
UN
IT.
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
24
DVD-1930CI / DVD-757
Digital Signal Process Block Diagram
C16
D18
A17
B15
DV
D-L
D8
CD
-LD
10
PD
-MO
NI
7
FS
(+)
2F
S(-
)3
TS
(+)
1T
S(-
)4C
N20
1
CN
201
CN
201
IC20
1(S
W)
IC50
1(S
DR
AM
)IC
101
(MIC
RO
CO
NT
RO
LLE
R)
FS
FS
(+)
SC
K1
CD
/DV
D
FS
EL
CLK
33M
FS
(-)
TS
(+)
TS
(-)
TS
DE
TE
CTO
R
CD
/DV
D19
Q25
1,Q
252
CDDV
D
AM
P
Q25
3,Q
254
AM
P
4
13
6
GN
D(D
VD-P
D)
6G
ND
(CD
-PD
)5
GN
D(L
D)
9
RF
SIG
NA
LP
RO
CE
SS
CIR
CU
IT
DV
D/C
DF
OR
MAT
TE
R
AU
DIO
I/F VID
EO
I/F
DM
A
BC
U
INS
T.R
OM
32B
ITC
PU
DAT
AR
AM
INT
ER
RU
PT
CO
NT
RO
LLE
RW
ATC
H D
OG
TIM
ER
CP
UI/F
TIM
ER
DE
CO
DE
RI/F
CP
UI/F
RE
AD
ME
MO
RY
DAT
AR
AM
DS
PD
EC
OD
ER
I/O PR
OC
ES
SO
R
INS
T.R
OM
DAT
AR
AM
INS
T.R
OM
SE
RIA
L
GE
NE
RA
LI/O IN
TE
RR
UP
TC
ON
TR
OLL
ER
TIM
ER
WAT
CH
DO
GT
IME
R
RE
MO
TE
CO
NT
RO
L
32B
IT C
PU
ST
RE
AM
I/F
EX
TE
RN
AL
ME
MO
RY
I/FS
DR
AM
EC
C
UM
AC
117
118
116
115
133
134
131
132
126
124
125
123
86
DE
BU
G
BC
U
INS
TR
AM
DAT
AR
AM
I2C
-SD
AI2
C-S
CL
I2C
-SD
AI2
C-S
CL
YC
(0-7
)
173
SD
0/S
PD
IF
172
SD
1
171
SD
2
170
SD
3
169
SD
4
168
SD
5
167
SD
6
SD
0/S
PD
IFS
D1
SD
2S
D3
SD
4S
D5
SD
6
166
SD
7
194
XS
HD
192
XS
AK
193
SD
CK
XSHD
XSAK
SDCK
255
SA
CD
-RE
SE
T
195
XS
RQ
191
SD
EF
SACD
-RES
ETXS
RQSD
EFP
SP
-WC
KS
AC
D-R
EA
DY
SA
CD
-DAT
A
PSP-
WCK
SACD
-REA
DYSA
CD-D
ATA
SA
CD
-LAT
CH
SACD
-LAT
CH
SA
CD
SA
CD
SD
RA
M D
ATA
(0-1
5)
SD
RA
M A
DD
RE
SS
(0-1
1)S
DR
AM
AD
DR
ES
S(0
-11)
230
247~
198
217~
2 13 42 53
~ ~
VID
EO
SIG
NA
L
22 26 29 35
~ ~S
DR
AM
DAT
A(0
-15)
PIC
K-U
PU
NIT
TO S
YS
TE
M
CO
NT
RO
L/S
ER
VO
BLO
CK
DIA
GR
AM
TO A
UD
IOB
LOC
KD
IAG
RA
M
27M
Hz
OS
C
27M
Hz
CLO
CK
X'T
AL
OS
CC
LKG
EN
E.
X10
1
DV
D M
AIN
CB
A U
NIT
TO V
IDE
OB
LOC
KD
IAG
RA
M
TO V
IDE
OB
LOC
KD
IAG
RA
M
TO S
AC
DB
LOC
KD
IAG
RA
M
TO A
UD
IOB
LOC
KD
IAG
RA
M
FD
Q (
0-15
)FA
DR
(0-
19)
FLA
SH
RO
M29 36 38 45
~ ~
FD
Q (
0-15
)
FAD
R (
0-19
)
~
1 9 16 25 48
~
163
162
15
ICS
03
1014
715
CLO
CK
-PU
LSE
3
190
TO V
IDE
OB
LOC
KD
IAG
RA
M
IC10
3(F
LAS
H R
OM
)
(CLO
CK
GE
NE
RAT
OR
)
66 6718
6
CLK
27M
176
183~
681768094
AU
DIO
SIG
NA
L
9 13S
CK
2TO
VID
EO
BLO
CK
DIA
GR
AM
CLK
33M
TO S
AC
DB
LOC
KD
IAG
RA
M
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
25
DVD-1930CI / DVD-757
Video Block DiagramgV
IDE
O S
IGN
AL
R(0
-7)
ICF
02(S
DR
AM
)
SD
RA
M
91 103~
2 13 31 56 74 85
~ ~ ~
24 27 60 66
~ ~
50 87
~IC
F01
(DIG
ITA
L V
IDE
O C
ON
VE
RT
ER
)
ICF
11(H
DT
V V
IDE
O E
NC
OD
ER
)
SD
RA
M D
ATA
(0-3
1)
SD
RA
M A
DD
RE
SS
(0-1
0)
NO
ISE
RE
DU
CE
R,
DE
INT
ER
LAC
ER
,FR
AM
E
RAT
E C
ON
VE
RT
ER
AN
DS
DR
AM
INT
ER
FAC
E
INP
UT
PR
OC
ES
OR
WIT
H A
UTO
SY
NC
AN
D A
UTO
AD
JUS
T
196
CLO
CK
GE
NE
RAT
ION
PLL
S
OU
TP
UT
PR
OC
ES
SO
R W
ITH
SY
NC
GE
NE
RAT
ION
AN
D D
IGTA
L A
NA
LOG
CO
NV
ER
TE
RS
VE
RT
ICA
LA
ND
HO
RIZ
ON
TAL
EN
HA
NC
ER
S
VE
RT
ICA
LA
ND
HO
RIZ
ON
TAL
SC
ALE
RS
YC
(0-7
)
YC
(0-7
)Y
C(0
-7)
199
205~
YC
(0-7
)
140
145~
148
155~
136
137
130
135~
126
127
49 56
~
57 58
~
61 65
~
75 79
~
68 70
~
VID
EO
DAT
AC
AP
TU
RE
BLO
CK
AU
DIO
DAT
AC
AP
TU
RE
BLO
CK
B(0
-7)
G(0
-7)
R(0
-7)
B(0
-7)
G(0
-7)
R(0
-7)
G(0
-7)
119
V-S
YN
C11
8H
-SY
NC
V-S
YN
CH
-SY
NC
122
HD
MI-
DE
125
VC
LK
21 6680
XO
RM
AS
K
PAN
EL
LIN
KT
RA
NS
MIT
TE
R
88
VID
EO
-Y(I
/P)
1010
VID
EO
-C
66
VID
EO
-Pb/
Cb
44
VID
EO
-Pr/
Cr
JK14
01S
-VID
EO
OU
T3
4
21
YC
WF
1
WF
3
IC14
02(V
IDE
O D
RIV
ER
)
4dB
AM
P2d
BA
MP
LPF
DR
IVE
R
D/A
114d
BA
MP
2dB
AM
PLP
FD
RIV
ER
6
104d
BA
MP
2dB
AM
PLP
FD
RIV
ER
8313
IC14
03(V
IDE
O D
RIV
ER
)
4dB
AM
P2d
BA
MP
LPF
DR
IVE
R
2dB
AM
PD
RIV
ER
4dB
AM
P2d
BA
MP
LPF
DR
IVE
R
3 1
5 6 7
22
VID
EO
-Y(I
)C
N60
1C
N16
01W
F2
TO D
IGIT
AL
SIG
NA
LP
RO
CE
SS
BLO
CK
DIA
GR
AM
DV
D M
AIN
CB
A U
NIT
AV
CB
A
CO
MP
OS
ITE
VID
EO
OU
T
VID
EO
-Pb/
Cb
OU
T
VID
EO
-YO
UT
VID
EO
-Pr/
Cr
OU
T
JK14
04
TO A
UD
IOB
LOC
KD
IAG
RA
M
HD
CP
EN
CR
YP
TIO
NE
NG
INE
HD
CP
KE
YS
EE
PR
OM
RE
GIS
TE
RS
AN
DC
ON
FIG
UR
ATIO
N
T.M
.D.S
DAT
A2-
CN
F01 3 1 6 4
HD
MI-
CO
NN
EC
TOR
T.M
.D.S
DAT
A2+
9 7 10 12
T.M
.D.S
DAT
A1-
T.M
.D.S
DAT
A1+
T.M
.D.S
DAT
A0-
T.M
.D.S
DAT
A0+
T.M
.D.S
CLO
CK
+
T.M
.D.S
CLO
CK
-
35 36 32 33 29 30 27 26
ICF
09(H
DM
I IN
TE
RFA
CE
)
13
6 5
2 3
ICF
04(3
.3V
5V
CO
NV
ER
TE
R)
1615
DD
C D
ATA
DD
C C
LOC
K
I2C
SLA
VE
1920
45 46I2
C-S
CL
I2C
-SD
A
I2C
-SC
LI2
C-S
DA
I2C
-SC
LI2
C-S
DA
TO D
IGIT
AL
SIG
NA
LP
RO
CE
SS
BLO
CK
DIA
GR
AM
19
18
6743 44
HP
D
QF
01+
3.3V
HO
T P
LUG
D
ET
EC
T
ICF
06
1 25
(FLI
P F
LOP
)
F/F
319
1X
TAL-
IN
CLO
CK
-PU
LSE
195
CLO
CK
-PU
LSE
SP
DIF
PC
M-D
ATA
3P
CM
-DAT
A2
PC
M-D
ATA
1P
CM
-DAT
A0
PC
M-L
RC
KP
CM
-BC
K SC
K2
TO D
IGIT
AL
SIG
NA
LP
RO
CE
SS
BLO
CK
DIA
GR
AM
TO D
IGIT
AL
SIG
NA
L P
RO
CE
SS
BLO
CK
D
IAG
RA
M
5 7 8 9 10 11 12 6
I2C
-SC
LI2
C-S
DA
39 38 37 23 24 22 2132 63
D/A
D/A
HD
TV
VID
EO
EN
CO
DE
R
DE
MU
X
PLL
53-5
5,58
-62
4-9,
12,1
3
16-1
8,26
-30
B(0
-7)
R(0
-7)
R(0
,1)
G(0
-7)
B(2
-7)
G(0
-7)
B(2
-7)/
R(0
,1)
B(0
-7)
G(0
-7)
SD
RA
M D
ATA
(0-3
1)
SD
RA
M A
DD
RE
SS
(0-1
0)
D/A
43
D/A
42
AU
DIO
SIG
NA
L
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
26
DVD-1930CI / DVD-757
Audio Block Diagram
ICS
02(A
UD
IO D
AC
)
JK12
02B
UF
FE
R
MUT
E-O
N
Q13
51
IC12
01
Q12
01
Q12
02
(AM
P)
AU
DIO
(L)-
OU
TF
UN
CT
ION
CO
NT
RO
LEN
HA
NC
ED
MU
LTI-
LEV
EL
DE
LTA
-SIG
MA
MO
DU
LATO
R
AU
DIO
(R)-
OU
T
AD
AC
-MD
SA
CD
-RE
SE
T
AD
AC
-MC
AD
AC
-ML
11 8 7
DA
CLP
F+
AM
PR
-CH
AU
DIO
(R)-
MU
TE
A-M
UT
E2
SP
DIF
PC
M-D
ATA
3P
CM
-DAT
A2
PC
M-D
ATA
1P
CM
-DAT
A0
PC
M-L
RC
KP
CM
-BC
K
12D
AC
LPF
+A
MP
L-C
H
30D
AC
LPF
+A
MP
R-C
H
31D
AC
LPF
+A
MP
L-C
H
28D
AC
LPF
+A
MP
R-C
H
29D
AC
LPF
+A
MP
L-C
H
9D
AC
LPF
+A
MP
R-C
H
10D
AC
LPF
+A
MP
L-C
H
Q12
04
PC
MI/F
DS
D-C
LKD
SD
-MX
LD
SD
-MX
RD
SD
-FL
DS
D-F
RD
SD
-CD
SD
-SW
DS
D-L
SD
SD
-RS
SD
6
SD
5
SD
2S
D3
SD
1S
D4
PC
MF
ILT
ER
(X8
DF
)IC
1204
AV
CB
A
5.1C
H A
MP
CB
A
DV
D M
AIN
CB
A U
NIT
JK12
01
DIG
ITA
LA
UD
IO
OU
T
OP
TIC
AL
CO
AX
IAL
CN
601
CN
1601
1212
AU
DIO
(L)
1414
AU
DIO
(R)
1919
AU
DIO
(R)-
MU
TE
1616
SP
DIF
CN
S01
CN
7102
1913
FR
ON
T-A
UD
IO(R
)17
11S
UR
RO
UN
D(L
)15
9S
UR
RO
UN
D(R
)13
7C
EN
TE
R
2115
FR
ON
T-A
UD
IO(L
)
115
SU
B W
OO
FE
R
1812
AU
DIO
(R)-
MU
TE
1610
SU
RR
OU
ND
(L)-
MU
TE
148
SU
RR
OU
ND
(R)-
MU
TE
126
CE
NT
ER
-MU
TE
2014
AU
DIO
(L)-
MU
TE
104
SU
B W
OO
FE
R-M
UT
E22
16A
UD
IO-M
UT
E2
93
AU
DIO
-MU
TE
82
M-M
UT
E
MUT
E-O
N
1 7
2 6
MUT
E-O
N
IC73
01
Q73
07
Q73
08
(AM
P)
FR
ON
T(L
)-O
UT
FR
ON
T(R
)-O
UT
Q73
02
JK71
01
Q73
01M
UTE-
ON
1 7
2 6Q
7351 Q73
52
MUT
E-O
N
IC74
01
Q74
03
Q74
04
(AM
P)
SU
RR
OU
ND
(L)
-OU
T
SU
RR
OU
ND
(R)
-OU
T
Q74
02
Q74
01M
UTE-
ON
1 7
2 6
MUT
E-O
N
IC75
01
Q75
03
Q75
04
(AM
P)
CE
NT
ER
OU
T
SU
BW
OO
FE
RO
UT
Q75
02
Q75
01M
UTE-
ON
1 7
2 6
DS
DF
ILT
ER
(X8
DF
)
51 50 49 48 47 4637 38 39 40 41 42 43 44 45 2 3
SY
ST
EM
CLO
CK
33 4
ICS
10
1 24
ICS
11
1 24
ICS
07
2 14
SD
0/S
PD
IFS
AC
D
SC
K1
TO
SA
CD
BLO
CK
DIA
GR
AM
TO
SA
CD
BLO
CK
DIA
GR
AM
TO
SA
CD
BLO
CK
DIA
GR
AM
TO
SY
ST
EM
CO
NT
RO
L/S
ER
VO
BLO
CK
DIA
GR
AM
TO
VID
EO
BLO
CK
DIA
GR
AM
TO
SY
ST
EM
CO
NT
RO
L/S
ER
VO
BLO
CK
DIA
GR
AM
TO
DIG
ITA
LS
IGN
AL
PR
OC
ES
SB
LOC
KD
IAG
RA
M
36S
AC
D-R
ES
ET
TO
DIG
ITA
LS
IGN
AL
PR
OC
ES
SB
LOC
KD
IAG
RA
M
AU
DIO
-MU
TE
M-M
UT
E
AU
DIO
(L)-
MU
TE
AU
DIO
(R)-
MU
TE
SU
RR
OU
ND
(L)-
MU
TE
SU
RR
OU
ND
(R)-
MU
TE
CE
NT
ER
-MU
TE
SU
B W
OO
FE
R-M
UT
E
DS
DI/F
Q74
51 Q74
52
Q75
51 Q75
52(A
ND
GAT
E)
(AN
D G
ATE
)
(AN
D G
ATE
)
Q12
03
1313
AU
DIO
(L)-
MU
TE
WF
4W
F6
WF
5
6A
UD
IO(L
)-M
UT
E
AU
DIO
SIG
NA
L
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
27
DVD-1930CI / DVD-757
SACD Block Diagram
ICS
01 (
SA
CD
MU
LTI C
HA
NN
EL
SIG
NA
L P
RO
CE
SS
)
ICS
12 (
SD
-RA
M)
6063 65 68 70 73 75 64 66 69 71 74 76
STRE
AMM
ANAG
ER
XS
HD
XS
RQ
SD
CK
SD
EF
SA
CD
-RE
SE
TS
AC
D-R
ES
ET
WC
K
AD
DR
ES
S (
0-11
)
DAT
A (
0-7)
SA
CD
-RE
AD
Y
SA
CD
-LAT
CH
SA
CD
-DAT
A
XS
RQ
SD
EF
SA
CD
-RE
SE
T
PS
P-W
CK
SA
CD
-RE
AD
Y
SA
CD
-LAT
CH
SA
CD
-DAT
A
TO D
IGIT
AL
SIG
NA
L P
RO
CE
SS
BLO
CK
DIA
GR
AM
TO D
IGIT
AL
SIG
NA
L P
RO
CE
SS
BLO
CK
DIA
GR
AM
TO A
UD
IOB
LOC
K D
IAG
RA
M
TO A
UD
IOB
LOC
K D
IAG
RA
M
TO A
UD
IOB
LOC
K D
IAG
RA
M
SD
CK
DSD
FADE
DSD
SIG
NAL
PRO
CESS
DSD
OUT
PUT
I/F
ADDR
ESS
BUS
DATA
BUS
DST
DECO
DER
6 27123931 168
XS
AK
167
166
164
165
173
174
175
176
169
170
171
172
11
PC
M-S
CLK
148,
149,
151,
152,
154-
157,
159-
162
131-
134,
136-
139
19-2
4,27
-32
2,3,
5,6,
8,9,
11,1
2
55 56
AD
AC
-MD
AD
AC
-MC
AD
AC
-MD
AD
AC
-MC
34
CLK
33M
TO S
YS
TE
MC
ON
TR
OL/
SE
RV
OB
LOC
K D
IAG
RA
M
SU
RR
OU
ND
(R)-
MU
TE
SU
RR
OU
ND
(R)-
MU
TE
SU
RR
OU
ND
(L)-
MU
TE
SU
RR
OU
ND
(L)-
MU
TE
SU
B W
OO
FE
R-M
UT
ES
UB
WO
OF
ER
-MU
TE
CE
NT
ER
-MU
TE
CE
NT
ER
-MU
TE
AU
DIO
(L)-
MU
TE
AU
DIO
(R)-
MU
TE
AU
DIO
(L)-
MU
TE
AU
DIO
(R)-
MU
TE
DS
D-C
LKD
SD
-MX
LD
SD
-MX
RD
SD
-FL
DS
D-F
RD
SD
-CD
SD
-SW
DS
D-L
SD
SD
-RS
DV
D M
AIN
CB
A U
NIT
XS
HD
XS
AK
SD
0/S
PD
IFS
D1
SD
2S
D3
SD
5S
D4
SD
6S
D7
SA
CD
-RE
SE
T
AU
DIO
SIG
NA
L
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
28
DVD-1930CI / DVD-757
Power Supply Block Diagram
IC10
06(S
HU
NT
RE
GU
LAT
OR
)R
EG
AC
1001
AC
CO
RD
F10
011A
250
VLI
NE
FIL
TE
R
L100
1D
1001
, D10
02
D10
04, D
1005 Q
1003
Q10
01
2 4 7
34
IC10
01E
RR
OR
VO
LTA
GE
DE
T
T10
01
11 12 13 1514 16 17 18
SW
ITC
HIN
GS
WIT
CH
ING
CO
NT
RO
L
1 2
6
BR
IDG
ER
EC
TIF
IER HO
T
HO
T C
IRC
UIT
. BE
CA
RE
FU
L.
D10
03
RE
CT
IFIE
R
D10
30
RE
CT
IFIE
R
D10
16
RE
CT
IFIE
R
Q10
16
Q10
05
Q10
11
Q10
15
Q10
02
CN
1001
Q10
04
-FL
EV
+5V
F1
P-O
N+
10V
EV
+3.
3V
P-O
N+
5V
+1.
2VR
EG
.
IC10
02D
1006
SC
HO
TT
KY
BA
RR
IER
SC
HO
TT
KY
BA
RR
IER
D10
08
F2
AV
CB
A
TO C
N40
1
Q10
08
LAT
CH
Q10
14
TO
SY
ST
EM
C
ON
TR
OL/
SE
RV
OB
LOC
K D
IAG
RA
M
INV
-PO
WC
ON
5,6
EV
+1.
2V7,
8,9
EV
+3.
3V12
,13
EV
+10
V11
P-O
N+
5V2,
3,4,
10P
-ON
+3.
3V21
PW
RC
ON
Q10
21
A
V
F
28E
V+
5V
CA
UT
ION
!F
ixed
vol
tage
(or
Aut
o vo
ltage
sel
ecta
ble)
pow
er s
uppl
y ci
rcui
t is
used
in th
is u
nit.
If M
ain
Fus
e (F
1001
) is
blo
wn
, che
ck to
see
that
all
com
pone
nts
in th
e po
wer
sup
ply
circ
uit a
re n
ot d
efec
tive
befo
re y
ou c
onne
ct th
e A
C p
lug
to th
e A
C p
ower
sup
ply.
Oth
erw
ise
it m
ay c
ause
som
e co
mpo
nent
s in
the
pow
er s
uppl
y ci
rcui
t to
fail.
NO
TE
:T
he v
olta
ge fo
r pa
rts
in h
ot c
ircui
t is
mea
sure
d us
ing
hot G
ND
as
a co
mm
on te
rmin
al.
"Ce
sym
bole
rep
rse
nte
un fu
sibl
e
fusi
on r
apid
e."
CA
UT
ION
!F
or c
ontin
ued
prot
ectio
n ag
ains
t fire
haz
ard,
repl
ace
only
with
the
sam
e ty
pe fu
se.
AT
TE
NT
ION
: P
our
une
prot
ectio
n co
ntin
ue le
s ris
qes
d'In
cele
n'u
tilis
er q
ue d
es fu
sibl
e de
mm
e ty
pe.
Ris
k o
f fi
re-r
epla
ce fu
se a
s m
arke
d."T
his
sym
bol m
eans
fast
ope
ratin
g fu
se."
A
V
F
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
29
DVD-1930CI / DVD-757
SCHEMATIC DIAGRAMS / CBAS AND TEST POINTS
Standard Notes
WARNING
Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by the mark # in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards.
Notes:1. Do not use the part number shown on these
drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared.
2. All resistance values are indicated in ohms (K = 103, M = 106).
3. Resistor wattages are 1/4W or 1/6W unless otherwise specified.
4. All capacitance values are indicated in F(P = 10-6 F).
5. All voltages are DC voltages unless otherwise specified.
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
30
DVD-1930CI / DVD-757
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES:
1. CAUTION:
FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQES D'INCELE N'UTILISER QUE DES FUSIBLE DE MME TYPE. RISK OF FIRE-REPLACE FUSE AS MARKED.
2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F1001) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
3. Note:1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
2. To maintain original function and reliability of repaired units, use only original replacement parts which are listed with their part numbers in the parts list section of the service manual.
4. Voltage indications for PLAY and STOP mode on the schematics are as shown below:
5. How to read converged lines
6. Test Point Information
A V
F
This symbol means fast operating fuse.Ce symbole represente un fusible a fusion rapide.
2 31 5.0(2.5)
5.0
The same voltage for both PLAY & STOP modes
Indicates that the voltage is not consistent here.
PLAY modeSTOP mode
(Unit: Volt)
3
2
1
A B C D
1-B1
1-D3
AREA D3
AREA B1
1-D3
Distinction AreaLine Number (1 to 3 digits)
Examples:1. "1-D3" means that line number "1" goes to the line number "1" of the area "D3". 2. "1-B1" means that line number "1" goes to the line number "1" of the area "B1".
: Indicates a test point with a jumper wire across a hole in the PCB.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.
www. xiaoyu163. com
QQ376315150 992894298
TEL 13942296513 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
31
DVD-1930CI / DVD-757
DVD Main 1/7 Schematic Diagram
1 NOTE: Either IC461 or IC462 is used for DVD MAIN CBA UNIT.
w w w . x i a o y u 1 6 3 . c o m
Q Q 3 7 6 3 1 5 1 5 0 992894298
T E L 1 3 9 4 2 2 9 6 5 1 3 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
32
DVD-1930CI / DVD-757
DVD Main 2/7 Schematic Diagram
w w w . x i a o y u 1 6 3 . c o m
Q Q 3 7 6 3 1 5 1 5 0 992894298
T E L 1 3 9 4 2 2 9 6 5 1 3 992894298051513673QQ
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
TE
L 1
39
42
29
65
13
37
63
15
15
0 8
92
49
82
99
http://www.xiaoyu163.com
http://www.xiaoyu163.com
http://www.xiaoyu163.comhttp://www.xiaoyu163.comhttp://www.xiaoyu163.com
33
DVD-1930CI / DVD-757
IC101 Voltage Chart
PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY
1 3.4 3.4 33 ~ ~ 65 ----- ----- 97 0.1
2 0 0 34 0 0 66 3.4 3.4 98 0.1
3 3.5 3.5 35 3.5 3.5 67 3.4 3.4 99 0.1
4 ----- ----- 36 ~ ~ 68 0 0 100 0.1
5 3.4 3.4 37 ~ ~ 69 3.5 3.5 101 0.1
6 3.4 3.4 38 ~ ~ 70 4.1 4.1 102 3.5
7 3.4 3.4 39 ~ ~ 71 3.4 3.4 103 0.9
8 3.5 3.5 40 ~