Upload
phungnhi
View
234
Download
0
Embed Size (px)
Citation preview
SERVICE MANUALMain SectionI SpecificationsI Preparation for ServicingI Adjustment ProceduresI Schematic DiagramsI CBAI Exploded ViewsI Parts List
When servicing the deck mechanism, refer to MK14 Deck Mechanism Section.
Deck Mechanism Part No.: N2460FL
DVD PLAYER & VIDEO CASSETTE RECORDER
DVP3355V/F7
IMPORTANT SAFETY NOTICE
Proper service and repair is important to the safe, reliable operation of all P&F Equipment. The service procedures recommended by P&F and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.
It is important to note that this service manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It also is important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. P&F could not possibly know, evaluate and advice the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, P&F has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by P&F must first use all precautions thoroughly so that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected.
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
MAIN SECTION
DVD PLAYER & VIDEO CASSETTE RECORDER
DVP3355V/F7
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-1Laser Beam Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2-1Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3-1Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4-1Preparation for Servicing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5-1Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6-1Electrical Adjustment Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7-1 How to Initialize the DVD Player & VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-8-1Firmware Renewal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9-1 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10-1Function Indicator Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11-1Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12-1Schematic Diagrams / CBA and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13-1Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14-1Wiring Diagram < VCR Section > . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15-1Wiring Diagram < DVD Section > . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15-2System Control Timing Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16-1IC Pin Function Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17-1Lead Identifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18-1Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19-1Mechanical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20-1Electrical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-21-1
Main SectionI SpecificationsI Preparation for ServicingI Adjustment ProceduresI Schematic DiagramsI CBAI Exploded ViewsI Parts List
1-1-1 E8E6ESP
SPECIFICATIONS
• Designs and specifications are subject to change without notice.• If there is a discrepancy between language translations, the default language understanding will be in English.
Video heads : 4-headsOutput signal format : NTSC colorPower source : 120 V AC +/- 10 %, 60 Hz +/- 0.5 %Power consumption : 16 W (standby : 0.5 W)Operating temperature : 41 °F (5 °C) to 104 °F (40 °C)
Dimensions : W: 17 3/16” (435 mm)H: 3 3/4” (94 mm)D: 9 3/16” (233 mm)
Weight : Approx 5.63lbs (2.55 kg)
1-2-1 DL8NLSP
LASER BEAM SAFETY PRECAUTIONS
This DVD player uses a pickup that emits a laser beam.
The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 1.8 inches (30 cm) away from the pickup lens when the diode is turned on. Do not look directly at the laser beam.
CAUTION: Use of controls and adjustments, or doing procedures other than those specified herein, may result in hazardous radiation exposure.
Location: Top of DVD mechanism.
Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin.
Drive Mechanism Assembly
Laser Beam Radiation
Laser Pickup
Turntable
LASER RADIATIONWHEN OPEN. DO NOT
STARE INTO BEAM.
CAUTION
1-3-1 DVDN_ISP
IMPORTANT SAFETY PRECAUTIONS
Product Safety NoticeSome electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by a # on schematics and in parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire, and/or other hazards. The Product’s Safety is under review continuously and new instructions are issued whenever appropriate. Prior to shipment from the factory, our products are carefully inspected to confirm with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
Precautions during ServicingA. Parts identified by the # symbol are critical for
safety. Replace only with part number specified.
B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements. Examples: RF converters, RF cables, noise blocking capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
D. Use specified insulating materials for hazardous live parts. Note especially:
1) Insulation tape
2) PVC tubing
3) Spacers
4) Insulators for transistors
E. When replacing AC primary side components (transformers, power cord, etc.), wrap ends of wires securely about the terminals before soldering.
F. Observe that the wires do not contact heat producing parts (heat sinks, oxide metal film resistors, fusible resistors, etc.).
G. Check that replaced wires do not contact sharp edges or pointed parts.
H. When a power cord has been replaced, check that 11~13 lb (5~6 kg) of force in any direction will not loosen it.
I. Also check areas surrounding repaired locations.
J. Be careful that foreign objects (screws, solder droplets, etc.) do not remain inside the set.
K. When connecting or disconnecting the internal connectors, first, disconnect the AC plug from the AC outlet.
L. When reassembling, be sure to use the original screws or specified screws listed in the parts list.
M. This unit is classified as a CLASS 1 LASER PRODUCT.
1-3-2 DVDN_ISP
Safety Check after ServicingExamine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts, and wires have been returned to their original positions. Afterwards, do the following tests and confirm the specified values to verify compliance with safety standards.
1. Clearance Distance
When replacing primary circuit components, confirm specified clearance distance (d) and (d’) between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1)
Table 1: Ratings for selected area
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
2. Leakage Current Test
Confirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below.
Measuring Method (Power ON):
Insert load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across the terminals of load Z. See Fig. 2 and the following table.
Table 2: Leakage current ratings for selected areas
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
AC Line Voltage Clearance Distance (d), (d’)
120 V ≥ 3.2 mm (0.126 inches)
AC Line Voltage Load Z Leakage Current (i) Earth Ground (B) to:
120 V 0.15 µF CAP. & 1.5 kΩ RES. Connected in parallel i ≤ 0.5 mA Peak Exposed accessible parts
Chassis or Secondary Conductor
Primary Circuit
Fig. 1
d' d
AC Voltmeter (High Impedance)
Exposed Accessible Part
B Earth Ground Power Cord Plug Prongs
Z
Fig. 2
1-4-1 DVDN_SN
STANDARD NOTES FOR SERVICING
Circuit Board Indications1. The output pin of the 3 pin Regulator ICs is
indicated as shown.
2. For other ICs, pin 1 and every fifth pin are indicated as shown.
3. The 1st pin of every male connector is indicated as shown.
Instructions for Connectors1. When you connect or disconnect the FFC (Flexible
Foil Connector) cable, be sure to first disconnect the AC cord.
2. FFC (Flexible Foil Connector) cable should be inserted parallel into the connector, not at an angle.
Pb (Lead) Free SolderWhen soldering, be sure to use the Pb free solder.
How to Remove / Install Flat Pack-IC
1. Removal
With Hot-Air Flat Pack-IC Desoldering Machine:
1. Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1)
2. Remove the flat pack-IC with tweezers while applying the hot air.
3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
CAUTION:
1. The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC.
2. Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape around the flat pack-IC to protect other parts from damage. (Fig. S-1-2)
Top View
Out In
Bottom ViewInput
5
10
Pin 1
Pin 1Fig. S-1-1
1-4-2 DVDN_SN
3. The flat pack-IC on the CBA is affixed with glue, so be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it.
With Soldering Iron:
1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)
2. Lift each lead of the flat pack-IC upward one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air desoldering machine. (Fig. S-1-4)
3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
Hot-airFlat Pack-ICDesolderingMachine
CBA
Flat Pack-IC
Tweezers
Masking Tape
Fig. S-1-2
Flat Pack-IC Desoldering Braid
Soldering Iron
Fig. S-1-3
Fine TipSoldering Iron
SharpPin
Fig. S-1-4
1-4-3 DVDN_SN
With Iron Wire:
1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)
2. Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5.
3. While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5.
4. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
5. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied.
2. Installation1. Using desoldering braid, remove the solder from
the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily.
2. The “” mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the pin 1 on the PCB when positioning for installation. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.)
3. Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges.
To Solid Mounting Point
Soldering Iron
Iron Wire
or
Hot Air Blower
Fig. S-1-5
Fine TipSoldering IronCBA
Flat Pack-ICTweezers
Fig. S-1-6
Example :
Pin 1 of the Flat Pack-ICis indicated by a " " mark. Fig. S-1-7
Presolder
CBA
Flat Pack-IC
Fig. S-1-8
1-4-4 DVDN_SN
Instructions for Handling Semi-conductorsElectrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work.
1. Ground for Human Body
Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.
2. Ground for Workbench
Be sure to place a conductive sheet or copper plate with proper grounding (1 MΩ) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing.
<Incorrect>
CBA
Grounding Band
Conductive Sheet orCopper Plate
1MΩ
1MΩ
<Correct>
CBA
1-5-1 E8E6EPFS
PREPARATION FOR SERVICING
How to Enter the Service ModeAbout Optical Sensors
Caution:
An optical sensor system is used for the Tape Start and End Sensors on this equipment. Carefully read and follow the instructions below. Otherwise the unit may operate erratically.
What to do for preparation
Insert a tape into the Deck Mechanism Assembly and press the [PLAY B] (VCR) button. The tape will be loaded into the Deck Mechanism Assembly. Make sure the power is on, connect S-INH (hollow) to GND. This will stop the function of Tape Start Sensor, Tape End Sensor and Reel Sensors. (If these TPs are connected before plugging in the unit, the function of the sensors will stay valid.) See Fig. 1.
Note: Because the Tape End Sensors are inactive, do not run a tape all the way to the start or the end of the tape to avoid tape damage.
Fig. 1
Q504
Q503
S-INH
1-6-1 E8E6DDC
CABINET DISASSEMBLY INSTRUCTIONS
1. Disassembly FlowchartThis flowchart indicates the disassembly steps to gain access to items to be serviced. When reassembling, follow the steps in reverse order. Bend, route, and dress the cables as they were originally.
2. Disassembly Method
Note:
(1) Identification (location) No. of parts in the figures
(2) Name of the part
(3) Figure Number for reference
(4) Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered. P = Spring, L = Locking Tab, S = Screw, CN = Connectore.g. 2(S-2) = two Screws (S-2), 2(L-2) = two Locking Tabs (L-2)
(5) Refer to “Reference Notes.”
Reference Notes1. CAUTION 1: Locking Tabs (L-1) and (L-2) are
fragile. Be careful not to break them.
1) Release three Locking Tabs (L-1).
2) Release three Locking Tabs (L-2), then remove the Front Assembly.
2. CAUTION 2: Electrostatic breakdown of the laser diode in the optical system block may occur as a potential difference caused by electrostatic charge accumulated on cloth, human body etc, during unpacking or repair work. To avoid damage of pickup follow next procedures.
1) Disconnect Connector (CN301). Remove two Screws (S-6) and lift the DVD Main CBA Unit. (Fig. D4)
2) Short the three short lands of FPC cable with solder before removing the FFC cable (CN201) from it. If you disconnect the FFC cable (CN201), the laser diode of pickup will be destroyed. (Fig. D4)
3. CAUTION 3: When reassembling, confirm the FFC cable (CN201) is connected completely. Then remove the solder from the three short lands of FPC cable. (Fig. D4)
4. When reassembling, solder wire jumpers as shown in Fig. D6.
ID/Loc. No.
Part Fig. No. Removal Note
[1] Top Case D1 4(S-1) ---
[2] Front Assembly D2 3(L-1), 3(L-2) 1
[3] Top Bracket D2 3(S-2) ---
[4]DVD Mechanism Assembly
D3 4(S-3), CN401, CN601 ---
[5] Partition Plate D3 2(S-4) ---
[6] Loader Holder D3 2(S-5) ---
[7] DVD Main CBA Unit D4 2(S-6), CN201, CN301 2, 3
[8]VCR Chassis Unit
D5 5(S-7), 2(S-8) ---
[9] Deck Assembly D6 Desolder,
2(S-9), (S-10) 4, 5
[1] Top Case
[2] Front Assembly
[3] Top Bracket
[4] DVD Mechanism Assembly [7] DVD Main CBA Unit
[5] Partition Plate
[6] Loader Holder
[8] VCR Chassis Unit
[9] Deck Assembly
[10] DVD Open/Close CBA
[11] Power SW CBA
[12] Main CBA
[10] DVD Open/Close CBA D6 Desolder ---
[11] Power SW CBA D6 Desolder ---
[12] Main CBA D6 ---------- ---
↓(1)
↓(2)
↓(3)
↓(4)
↓(5)
ID/Loc. No.
Part Fig. No. Removal Note
1-6-2 E8E6DDC
5. Before installing the Deck Assembly, be sure to place the pin of LD-SW on Main CBA as shown in Fig. D6. Then, install the Deck Assembly while aligning the hole of Cam Gear with the pin of LD-SW, the shaft of Cam Gear with the hole of LD-SW as shown in Fig. D6.
(S-1)[1] Top Case
Fig. D1
(L-1)
(L-2)
(L-1)
[2] Front Assembly
Fig. D2
(S-2)
(S-2)
[3] Top BracketFig. D3
CN401CN601
(S-3)
(S-3)
(S-3)
(S-4)(S-5)
[5] Partition Plate
[6] Loader Holder
[4] DVD Mechanism Assembly
CN201CN301
(S-6)[7] DVD Main CBA Unit
DVD MechanismA
Fig. D4
View for A
Short the three short lands by soldering.(Either of two places.)
Connector
1-6-3 E8E6DDC
Fig. D5
(S-7)
(S-7)
(S-8)
[8] VCR Chassis Unit
(S-7)(S-8)
1-6-4 E8E6DDC
Fig. D6
(S-9)
(S-10)
(S-9)
[10] DVD Open/Close CBA
FE Head
Cylinder Assembly
ACE HeadAssembly
Desolder
Lead withblue stripe
BOTTOM VIEWLead connections of Deck Assembly and Main CBA
[12] Main CBA
SW512LD-SW
LD-SW Pin
Hole
Hole
Shaft
Cam Gear
[12] Main CBA
[9] Deck Assembly
Pin
[12] Main CBA
[9] Deck Assembly
From FE Head
DesolderFromCapstan MotorAssembly
Printing side
Desolder
FromCylinder Assembly
FromACE HeadAssembly
Lead withblue stripe
Lead withblue stripe
Desolder
Lead withblack stripe
[11] Power SW CBA
Lead with blue stripeDesolder
1-6-5 E8E6DDC
3. HOW TO EJECT MANUALLY1. Remove the Top Case, Front Assembly and Top Bracket.
2. Remove four Screws (S-3) in Fig. D3. Do not disconnect connectors.
3. While lifting up the DVD Mechanism, rotate the roulette in the direction of the arrow as shown below.
4. Pull the tray slowly manually.
The gear is turned to the direction of the arrow.
The Back of DVD Mechanism Assembly
DVD Mechanism
1-7-1 E8E6EEA
ELECTRICAL ADJUSTMENT INSTRUCTIONS
General Note: “CBA” is abbreviation for “Circuit Board Assembly.”
NOTE:
1. Electrical adjustments are required after replacing circuit components and certain mechanical parts. It is important to do these adjustments only after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available.
2. To perform these alignment / confirmation procedures, make sure that the tracking control is set in the center position: Press either [TRACKING L] or [TRACKING K] button on the front panel first, then the [PLAY B] (VCR) button on the front panel.
Test Equipment Required1. Oscilloscope: Dual-trace with 10:1 probe,
V-Range: 0.001~50 V/Div., F-Range: DC~AC-20 MHz
2. Alignment Tape (FL8A)
Head Switching Position AdjustmentPurpose: To determine the Head Switching position during playback.
Symptom of Misadjustment: May cause Head Switching noise or vertical jitter in the picture.
Note: TP751(V-OUT), TP302(RF-SW), VR501(Switching Point) --- Main CBA
Reference Notes:
Playback the Alignment tape and adjust VR501 so that the V-sync front edge of the CH1 video output waveform is at the 6.5H ± 1H (412.7 µs ± 63.5 µs) delayed position from the rising edge of the CH2 head switching pulse waveform.
Test point Adj. Point Mode Input
TP751(V-OUT)TP302(RF-SW)
GND
VR501(Switching Point)
PLAY (SP) -----
Tape Measurement Equipment Spec.
FL8A Oscilloscope 6.5H ± 1H(412.7µs±63.5µs)
Connections of Measurement Equipment
Figure 1
Oscilloscope
Main CBATP751
CH1 CH2Trig. (+)
GNDTP302
EXT. Syncronize Trigger Point
1.0HCH1
CH2
Switching Pulse
V-Sync0.5H
6.5H±1H (412.7µs±63.5µs)
1-8-1 E8E21INT
HOW TO INITIALIZE THE DVD PLAYER & VCR
To put the program back at the factory-default, initialize the DVD player & VCR as the following procedure.
< DVD Section >1. Press [DVD], [1], [2], [3], [4], and [DISPLAY]
buttons on the remote control unit in this order. Fig. a appears on the screen.
2. Press [CLEAR] button on the remote control unit. Fig. b appears on the screen.
When “OK” appears on the screen, the factory default will be set.
3. To exit this mode, press [ ] button.
MODEL : ******* Version : *.** Region : *
EXIT: POWEREEPROM CLEAR : CLEAR
Fig. a
"*******" differs depending on the models.
MODEL : ******* Version : *.** Region : *
EEPROM CLEAR : OK
EXIT: POWEREEPROM CLEAR : CLEAR
"*******" differs depending on the models.
Fig. b
1-9-1 E8E6DFW
FIRMWARE RENEWAL MODE
1. Turn the power on and remove the disc on the tray.
2. To put the DVD player into version up mode, press [DVD], [9], [8], [7], [6], and [SEARCH] buttons on the remote control unit in that order. The tray will open automatically. Fig. a appears on the screen.
The DVD player can also enter the version up mode with the tray open. In this case, Fig. a will be shown on the screen while the tray is open.
3. Load the disc for version up.
4. The DVD player enters the F/W version up mode automatically. Fig. b appears on the screen. Make sure to insert the proper F/W for the state of this model.
The appearance shown in (*1) of Fig. b is described as follows:
5. After programming is finished, the tray opens automatically. Fig. c appears on the screen and the checksum will be shown in (*2) of Fig. c.
At this time, no button is available.
6. Remove the disc on the tray.
7. Unplug the AC cord from the AC outlet. Then plug it again.
8. Turn the power on by pressing the [ ] button and the tray will close.
9. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order. Fig. d appears on the screen.
10. Press [CLEAR] button on the remote control unit. Fig. e appears on the screen.
When “OK” appears on the screen, the factory default will be set. Then the firmware renewal mode is complete.
11. To exit this mode, press [ ] button.
No. Appearance State
1 Reading... Sending files into the memory
2 Erasing... Erasing previous version data
3 Programming... Writing new version data
F/W Version Up Mode Model No : *******VERSION : *.**
Please insert a DISCfor F/W Version Up.
EXIT: POWER
"*******" differs depending on the models.
Fig. a Version Up Mode Screen
VERSION : ************.***Reading...
F/W Version Up Mode Model No : *******VERSION : *.**
Fig. b Programming Mode Screen
"*******" differs depending on the models.
(*1)
VERSION :CompletedSUM : 7ABC
F/W Version Up Mode Model No : *******VERSION : *.**************.***
"*******" differs depending on the models.
Fig. c Completed Program Mode Screen
MODEL : ******* Version : *.** Region : *
EXIT: POWEREEPROM CLEAR : CLEAR
Fig. d
"*******" differs depending on the models.
MODEL : ******* Version : *.** Region : *
EEPROM CLEAR : OK
EXIT: POWEREEPROM CLEAR : CLEAR
"*******" differs depending on the models.
Fig. e
1-10-1 E8E6DTR
TROUBLESHOOTING
1 Power Supply Section
FLOW CHART NO.1The power cannot be turned on.
Is the fuse (F1002) normal?
Is normal state restored when once unplugged power cord is plugged again after several seconds.
Is the AL+5V(1) line voltage normal?
Check each rectifying circuit of secondary circuit and service it if defective.
See FLOW CHART No.2 <The fuse blows out.>
Check for lead or short-circuiting of primarycircuit component and service it if defective.(IC1003, Q1002, T1001, D1001, D1002, D1003,D1004, D1011, D1014, C1013, R1013)
Yes
Yes
Yes
No
No
No
FLOW CHART NO.2The fuse blows out.
After servicing, replace the fuse (F1002).
Check the presence that the primary componentis leaking or shorted and service it if defective.
Check the presence that the rectifying diode or circuit is shorted in each rectifying circuit of secondary side and service it if defective.
FLOW CHART NO.3When the output voltage fluctuates.
No
Yes
Does the secondary side photo coupler circuitoperate normally?
Check the circuit and service it if defective.(IC1003, D1006, D1007, D1009, D1012)
Check the circuit and service it if defective.(IC1001, D035, D041)
FLOW CHART NO.4When buzz sound can be heard in the vicinity of power circuit.
Check if there is short circuit on the rectifying diode and the circuit in each rectifying circuit of secondary side and service it if defective. (D013,D015,D016,D1008,D1010,D1020,IC1002,IC1004,Q055,Q056,Q063,Q1004,Q1006,Q1011)
No
Yes
FLOW CHART NO.5AL-30V is not outputted.
Is approximately -30V voltage supplied to the anode of D1010?
Check D1010, C1002 and their periphery, and service it if defective.
Check for load circuit short-circuiting or leak, and service it if defective.
1-10-2 E8E6DTR
DVD-P-ON+12V is not outputted. FLOW CHART NO.10
Is approximately +12V voltage supplied to the emitter of Q1006?
Replace Q1006.
No
NoYes
Yes
Is the "L" pulse (approximately 0V) outputted to the collector of Q1005?
Check D015, D031, C018 and their periphery, and service it if defective.
Check Q1005, Q1101 and PWRCON line, and service it if defective.
FLOW CHART NO.7P-ON+5V is not outputted. (P-ON+9V is outputted normally.)
Is approximately +5V voltage supplied to the collector of Q056?
Replace Q056.
No
NoYes
YesIs the "H" pulse inputted into the base of Q056?
Check D016, D035, L009, C020, C021, and their periphery, and service it if defective.
Check R057 and their periphery, and service it if defective.
FLOW CHART NO.6P-ON+9V is not outputted.
Is approximately +11V voltage supplied to the collector of Q055?
Check Q052, D052 and their periphery, and service it if defective.
No
NoYes
YesIs the "L" pulse inputted to the base of Q052?
Check D015, D031, D080, D082, C018, and their periphery, and service it if defective.
Replace IC501.
FLOW CHART NO.8TIMER+5V is not outputted. (AL+5V(1) is outputted normally.)
Is approximately +4.5V voltage inputted to the base of Q063?
No
YesReplace Q063.
Check Q064, D062 and their periphery, and service it if defective.
FLOW CHART NO.9AL+18V is not outputted.
Is approximately +20V voltage supplied to the cathode of D013?
No
YesCheck D504, R092, R095, and service it if defective.
Check D013, C013 and their periphery, and service it if defective.
Is approximately +10V voltage inputted to the base of Q055?
No
YesReplace Q055.
1-10-3 E8E6DTR
No
Yes
Check D1008, C1007 and their periphery, and service it if defective.
FLOW CHART NO.11EV+3.3V is not outputted.
FLOW CHART NO.12DVD-P-ON+3.3V is not outputted. (DVD-P-ON+12V is outputted normally.)
Is approximately +4V voltage supplied to Pin(4) of IC1004?
Replace IC1004.
Is the "H" pulse (approximately 4V) inputted to the base of Q1011?
Replace Q1011.
Check R1077 and their periphery, and service it if defective.
Yes
YesNo
Is approximately +3.3V voltage supplied to the collector of Q1011?
See FLOW CHART NO.11 <EV+3.3V is not outputted.>No
Yes
Is approximately +5V voltage supplied to the collector of Q1004?
No
NoIs approximately +2.8V voltage supplied to Pin(4) of IC1002?
FLOW CHART NO.14EV+1.2V is not outputted.
Replace IC1002.
Check D1020,C1014,L1020, C1015, and their periphery, and service it if defective.
Yes
FLOW CHART NO.13DVD-P-ON+5V is not outputted. (DVD-P-ON+12V is outputted normally.)
Is the "H" pulse inputted to the base of Q1004?
Replace Q1004.
Check R1068 and their periphery, and service it if defective.
Check D016, D035, L009, C020, C021 and their periphery, and service it if defective.
Yes
No
1-10-4 E8E6DTR
2 DVD Section
YesNo
FLOW CHART NO.1The key operation is not functioning.
Are the contact point and the installation state of the key switches (SW2001, SW2002, SW2003, SW2005, SW2006) normal?
When pressing each key switches (SW2001, SW2002, SW2003, SW2005, SW2006), do the voltage of each pin of CN1001 (shown below) change to "H" (+3.3V) from "L" (0V)?SW2001 → CN1001 24PINSW2002 → CN1001 26PINSW2003 → CN1001 25PINSW2005 → CN1001 18PINSW2006 → CN1001 19PIN
Check the key switches (SW2001, SW2002, SW2003, SW2005, SW2006) and their periphery, and service it if defective.
No Re-install the key switches (SW2001, SW2002, SW2003, SW2005, SW2006) correctly or replace the poor switch.
FLOW CHART NO.2No DVD operation is possible from the remote control unit. (Operation is possible from the unit.)
Replace the RM2001 (remote control receiver).Replace remote control unit if needed.
Is the "H" pulse inputted to the base of Q2014?
Replace Q2014.
Is the "L" pulse sent out from Pin(1) terminal of the RM2001 (remote control receiver) when the remote control unit is activated?
Is the "L" pulse signal supplied to Pin(22) of CN1001?
Replace the DVD Main CBA Unit.
Yes
YesYes
Replace IC501.No
Replace DVD Main CBA Unit.Yes
Yes
Is approximately +5V voltage supplied to Pin(3) terminal of the RM2001 (remote control receiver)?
Yes No
Check AL+5V(1) line, and service it if defective.No
No
FLOW CHART NO.3The disc tray cannot be opened and closed. (It can be done using the remote control unit.)
Does the voltage of Pin(24) on CN1001 become to +3.3V from 0V when pressing "OPEN/CLOSE" button on the unit?
Refer to "FLOW CHAR NO.4" <The disc tray cannot be opened and closed.>
Replace the "OPEN/CLOSE" button (SW2001).No
Yes
FLOW CHART NO.4The disc tray cannot be opened and closed. (It can not be done using the unit and the remote control unit.)The [No Disc] indication.Both picture and sound do not operate normally.
Replace the DVD Main CBA Unit.
Original DVD Main CBA Unit is poor.
Replace the DVD Mechanism.
No improvement can be found.No
1-10-5 E8E6DTR
FLOW CHART NO.5
Picture does not appear normally.
Set the disc on the disc tray, and playback.
Are the video signals outputted to each pin of CN1601?
Replace the DVD Main CBA Unit or the DVD Mechanism.
Check the line between each pin of CN1601 and each pin of IC1402, and service it if defective.
Is approximately 5V voltage applied to the Pin(4, 12) of IC1402?
Replace IC1402.
Check DVD-P-ON+5V line and service it if defective.
Check the periphery of JK1403 from Pins (10, 11, 13) of IC1402 and service it if defective.
Check the periphery of JK1401 from Pin (13) of IC1402 and service it if defective.
Check the periphery of JK1401 from Pin (15) of IC1402 and service it if defective.
CN1601 8PIN → IC1402 3PIN VIDEO-(I/P)CN1601 6PIN → IC1402 6PIN VIDEO-Pb/CbCN1601 4PIN → IC1402 8PIN VIDEO-Pr/Cr CN1601 10PIN → IC1402 1PIN VIDEO-C
Are the video signals shown above inputted into each pin of IC1402?
Are the video signals outputted to each pin of IC1402?
Are the video signals outputted to the specific output terminal?
Are the component video signals outputted to the VIDEO OUT terminal (JK1403)?
Are the luminance signals outputted to the S-OUT terminal (JK1401)?
Are the chroma signals outputted to the S-OUT terminal (JK1401)?
Yes
Yes
Yes
Yes
No
No
NoNo
No
No
No
No
CN1601 8PIN VIDEO-Y(I/P)CN1601 6PIN VIDEO-Pb/CbCN1601 4PIN VIDEO-Pr/CrCN1601 10PIN VIDEO-C
IC1402 3PIN VIDEO-Y(I/P)IC1402 6PIN VIDEO-Pb/CbIC1402 8PIN VIDEO-Pr/CrIC1402 1PIN VIDEO-C
IC1402 13PIN VIDEO-Y(I/P)IC1402 11PIN VIDEO-Pb/Cb IC1402 10PIN VIDEO Pr/CrIC1402 15PIN VIDEO-CIC1402 14PIN DVD VIDEO
Are the composite video signals outputted to the VIDEO OUT terminal (JK751)?
Are the composite video signals outputted to Pin(15) of IC751?
Replace IC751. Replace IC501.Check the line between Pin(15) of IC751 and JK751 and service it if defective.
Are the "L" pulse inputted into Pin(9,10,11) of IC751?
Yes No
No
Yes
1-10-6 E8E6DTR
Check the line between Pin(4,14) of IC751 and JK751, and their periphery, and service it if defective.
FLOW CHART NO.6
Audio is not outputted.
Set the disc on the disc tray, and playback.
Are the analog audio signals outputted to each pin of CN1601?
Is the "H" level mute signals outputted to Pin(13) of CN1601?
CN1601 12PIN DVD-AUDIO(L)CN1601 14PIN DVD-AUDIO(R)
IC1201 7PIN DVD-AUDIO(L)IC1201 1PIN DVD-AUDIO(R)
IC1201 6PIN DVD-AUDIO(L)IC1201 2PIN DVD-AUDIO(R)
Replace the DVD Main CBA Unit or the DVD Mechanism.
Replace the DVD Main CBA Unit.
Replace IC1201.
Check the periphery between Pins(1,7) of IC1201 and JK756, and service it if defective.
Check each line between each pin of CN1601 and each pin of IC1201, and service it if defective.
CN1601 12PIN → IC1201 6PIN DVD-AUDIO(L)CN1601 14PIN → IC1201 2PIN DVD-AUDIO(R)
Are the analog audio signals inputted to each pin of IC1201.
Are the analog audio signals outputted to each pin of IC1201?
Are the audio signals outputted to the specific output terminal?
Are the audio signals outputted to the L/R OUT terminal (JK756)?
Are the audio signals outputted to the L/R OUT terminal (JK751)?
Yes
Yes
Yes
Yes
No
No
No
No
No
No
Are the audio signals outputted to Pin(4,14) of IC751?
Replace IC751. Replace IC501.
Are the "L" pulse inputted into Pin(9,10,11) of IC751?
Yes No
No
Yes
1-10-7 E8E6DTR
3 VCR Section
Yes
Yes
No
No
FLOW CHART NO.1
FLOW CHART NO.2
The key operation is not functioning.
Are the contact point and the installation state of the key switches normal?
Is the control voltage normally inputted into Pin(66,67) of IC501?
Re-install some key switches correctly orreplace some key switches.
Check the key switches and their periphery, and service it if defective.
Replace IC501.
0.51
0.92
1.27
1.61
1.98
2.39
2.90
3.60
4.30-----
-----
-----
-----
-----
S-INH
TRACKINGDOWN
TRACKINGUP
OUTPUT
-----
-----
-----
PLAY
REC
FF
STOP/EJECT
REW
POWER
Terminal voltage of IC501-66,67 KEY-1IC501-67
KEY-2IC501-66
(V)
Replace the RM2001 (remote control receiver)or replace remote control unit.
Check the line between the RM2001 (remote control receiver) and the Pin(5) of IC501, and service it if defective.
Replace IC501.
Is the "L" pulse sent out from Pin(1) terminal of the RM2001 (remote control receiver) when the remote control unit is activated?
Is the "L" pulse signal supplied to the Pin(5) of IC501?
Yes
Is approximately +5V voltage supplied to the Pin(3) terminal of the RM2001 (remote control receiver)?
Yes
Yes
No
Check AL+5V(1) line and service it if defective.No
No
No VCR operation is possible from the remote control unit. (Operation is possible from the unit.)
1-10-8 E8E6DTR
FLOW CHART NO.3
FLOW CHART NO.4
Cassette tape can not be loaded.
Cassette tape is ejected right after the loading.
FLOW CHART NO.5Cassette tape can not be ejected.
When loading a cassette tape, on Pin(69) of IC501, does the "L" pulse switch to the "H" pulse?
When loading a cassette tape, on Pin(69) of IC501, does the "L" pulse switch to the "H" pulse?
When loading a cassette tape, on Pin(62) of IC501, does the "L" pulse switch to the "H" pulse?
When pressing the eject button, does the CapstanMotor start rotating?
Refer to "FLOW CHART NO.6 " <The Capstan Motor does not rotate>.
Check the Reel Disc or Clutch Assembly, etc., and service it if defective.
Replace IC501.
Replace the Capstan Motor.
Replace the Loading Motor.
While the Capstan Motor is rotating, is the TakeupReel rotating?
Is the Loading Motor rotating?
Check the Cam Gear or Rack Assembly, etc, and service it if defective.
While the Takeup Reel is rotating, is the reel pulse signal inputted to Pin(3) of IC501?
While the reel pulse signal is inputting, is "L" pulse inputted to Pin(21) of IC501?
Is the specified voltage (approximately 13V) outputted to the terminal of the Lading Motor?
When loading a cassette tape, does the LD-SW operate normally?
When loading a cassette tape, is the specified voltage (approximately 13V) outputted to the terminal of the Loading Motor Unit?
Check the line between the start sensor and Pin(69) of IC501, and service it if defective.
Replace the Capstan Motor Unit.
Replace the Loading Motor Unit.
Replace IC501.
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Check the line between the start sensor and Pin(69) of IC501, and service it if defective.
Check the line between the end sensor and Pin(62) of IC501, and service it if defective.
Check the line between the LD-SW(SW512) and Pin(68) of IC501, and service it if defective.
Check the line between the Takeup Reel sensor and Pin(3) of IC501, and service it if defective.
No
No
No
No
No
No
No
No
No
No
1-10-9 E8E6DTR
FLOW CHART NO.6Capstan Motor does not rotate.
FLOW CHART NO.7Drum Motor does not rotate.
FLOW CHART NO.8Drum Motor rotates only for a few seconds.
FLOW CHART NO.9RF-SW signal is not outputted.
Is the Drum Motor rotating?
Is approximately +5V voltage supplied to Pin(2) of CN502?
Is approximately +12V voltage supplied to Pin(1,11) of CN502?
Replace the Capstan Motor.
Is over approximately 2.6V voltage supplied to Pin(5) of CN502?
Check the P-ON+5V line and service it if detective.
Check the line between Pin(5) of CN502 and Pin(28) of IC501, and service it if detective.
Check the AL+12V line and service it if detective.
Check the P-ON+5V line and service it if detective.
Check the line between Pin(8) of CN502 and Pin(29) of IC501, and service it if detective.
Check the AL+12V line and service it if detective.
Check the AL+12V line and service it if detective.
D-FG
D-PG
5Vp-p
2.5Vp-p
D-FG
DRUM PG/FG SIGNAL WAVEFORM
Replace IC501.
No
No
No
No
No
No
No
No
No
No
No
Yes
Yes
Yes
Is approximately +5V voltage supplied to Pin(2) of CN502?
Is the drum PG/FG signal inputted to Pin(47) of IC501?
Is the drum PG/FG signal inputted to Pin(47) of IC501?
Is approximately +12V voltage supplied at Pin(1,11) of CN502?
Is the RF-SW signal outputted to Pin(18) of IC501?
Is approximately +12V voltage supplied Pin(1,11) of CN502?
Replace the Capstan Motor or Cylinder Assembly.
Replace the Capstan Motor or the Cylinder Assembly.
Replace the Capstan Motor or the Cylinder Assembly.
Replace the Capstan Motor or the Cylinder Assembly.
Refer to "FLOW CHART NO.7" <Drum Motor does not rotate> and "FLOW CHART NO.8" <Drum Motor rotates only for a few seconds>.
Is over approximately 2.6V voltage supplied to Pin(8) of CN502?
Yes
Yes
Yes
Yes
Replace IC501.
Yes
Yes
Yes
Yes
1-10-10 E8E6DTR
FLOW CHART NO.10Video E-E does not appear.
Is the Video signal inputted to Pin(28,30) of IC301? Check the line between the video input terminal (rear) and Pin(28) of IC301, and service it if defective.Check the line between the video input terminal (front) and Pin(30) of IC301, and service it if defective.
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes No
NoNo
No
No
Is the C-SYNC signal outputted to Pin(25) of IC301?
Is the C-SYNC signal inputted to Pin(41) of IC501? Is approximately +5V voltage supplied to Pin(23) of IC301?
Is the serial data, clock and chip select signal supplied to Pin(53, 54, 55) of IC301?
Check the P-ON+5V line and service it if defective.
Yes
No
No
Is the "H" pulse inputted into Pin(9,10,11)of IC751?
Yes No
Replace IC751. Replace IC501.
Is approximately 5V voltage supplied to Pin(16) of IC751, and approximately -5V voltage supplied to Pin(7) of IC751?
Check the AL+5V line and the AL-30V line (R777,D777), and service it if defective.
Check the line between Pin(25) of IC301 and Pin(41) of IC501, and service it if defective.
Check the line between Pin(53,54,55) of IC301 and Pin(14,15,16) of IC501, and service it if defective.
Check the line between Pin(15) of IC751 and video output terminal (JK751), and service it if defective.
Check the line between Pin(26) of IC301 and Pin(1) of IC751, and service it if defective.
Is the video signal inputted into Pin(1) of IC751?
Is the video signal outputted to Pin(15) of IC751?
Replace IC301.
1-10-11 E8E6DTR
FLOW CHART NO.11Hi-Fi E-E audio does not operate normally.
Check the peripheral circuit of the front input terminal and service it if defective.
Check the peripheral circuit of the rear input terminal and service it if defective.
Check the circuit of P-ON+5V and P-ON+9V, and service it if defective.
Is the 5V voltage supplied to Pin(25, 40, 51) of IC451, and the 9V voltage supplied to Pin(58) of IC451?
Is the serial data and the clock signal supplied to Pin(42, 43) of IC451?
Is the sub carrier signal (3.58 MHz) inputted to Pin(45) of IC451?
Is the audio signal outputted to Pin(53, 57) of IC451?
Is the audio signal inputted into Pin(3,13) of IC751?
Is each signal supplied to each pin of IC451 as below?
Front input terminalL-ch R-ch
Pin(15) Pin(10)Pin(14) Pin(9)Rear input terminal
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Is the audio signal outputted to Pin(4,14) of IC751?
Yes
NoNo
No
No
No
No
No
No
Check the line between Pin(42, 43) of IC451 and Pin(12,13) of IC501, and service it if defective.
Check the line between Pin(36) of IC451 and Pin(7) of IC501, and service it if defective.
Check the line between the Pin(49) of IC302 and Pin(45) of IC451, and service it if defective.
Check the line between Pin(53, 57) of IC451 and Pin(3,13) of IC751, and service it if defective.
Check the line between Pin(4,14) of IC751 and the audio output terminal (JK751), and service it if defective.
Replace IC451.
Is the "L" pulse inputted into the Pin(36) of IC451?
Yes
No
No
NoYes
Is approximately 5V voltage supplied to Pin(16) of IC751, and approximately -5V voltage supplied to Pin(7) of IC751?
Replace IC751. Replace IC501.
Check the AL+5V line and the AL-30V line (R777,D777), and service it if defective.
Is the "H" pulse inputted into the Pins(9,10,11) of IC751?
1-10-12 E8E6DTR
FLOW CHART NO.13Hi-Fi audio can not be playbacked normally. (Hi-Fi E-E mode is normal.)
FLOW CHART NO.14Audio can not be recorded normally in the linear audio mode. (E-E mode is normal.)
Is the audio signal inputted into Pin(76,78,80) of IC301?
Does the Bias oscillation circuit operate normally?
Is the audio signal outputted to Pin(10) of IC301?
Is the Playback Envelope signal outputted to Pin(30) of IC451?
Replace IC301.
Is the Hi-Fi-H-SW signal inputted into to Pin(27) of IC451?
Yes
Yes
Yes
Is the audio signal outputted to Pin(9) of IC301?Yes
Yes
Replace ACE head.
Yes No
No
No
No
Check the Hi-Fi-H-SW line between Pin(27) of IC451 and Pin(25) of IC501, and service it if defective.
Check the line between Pin(61) of IC451 and Pin(76,78,80) of IC301, and service it if defective.
Check the Bias oscillation circuit (Q421,Q422,Q425,Q426) and service it if defective.
Replace IC451.
Replace Cylinder Assembly.
No
Replace IC301.No
FLOW CHART NO.12Hi-Fi audio can not be recorded normally. (E-E mode is normal.)
Is the REC FM signal outputted to Pin(26) of IC451?
Is the line between Pin(8) of CN253 and Pin(21) of IC451 normal?
Replace the Cylinder Assembly.
Yes
Yes
NoReplace IC451.
No Service the line between Pin(8) of CN253 and Pin(21) of IC451.
FLOW CHART NO.15Audio can not be playbacked normally in the linear audio mode. (E-E mode is normal.)
Is there no dirt on the surface of ACE head assembly?
Is the audio signal supplied to Pin(6) of IC301?
Replace IC301.
Is the audio signal outputted to Pin(10) of IC301?
Check the line between Pin(62) of IC301 and Pin(4) of IC451, and service it if defective.
Readjust the height of the ACE head assembly.
Clean the surface of ACE head assembly.
Yes
Is the height of ACE head assembly appropriate?
Yes
Replace the ACE head assembly.
Yes
NoYesNo
No
No
1-11-1 E8E6EFIS
FUNCTION INDICATOR SYMBOLS
Note: If a mechanical malfunction occurs, the power is turned off. When the power comes on again after that by pressing [POWER ON] button, an error message is displayed on the TV screen for 5 seconds.
TV screen
When reel or capstan mechanism is not functioning correctly
When tape loading mechanism is not functioning correctly
When cassette loading mechanism is not functioning correctly
When the drum is not working properly
P-ON+5V Power safety detection
Cause Indicator Active
When reel or capstan mechanism is not functioning correctly “EJECT A R” is displayed on a TV screen. (Refer to Fig. 1.)
When tape loading mechanism is not functioning correctly “EJECT A T” is displayed on a TV screen. (Refer to Fig. 2.)
When cassette loading mechanism is not functioning correctly “EJECT A C” is displayed on a TV screen. (Refer to Fig. 3.)
When the drum is not working properly “EJECT A D” is displayed on a TV screen. (Refer to Fig. 4.)
P-ON+5V Power safety detection “EJECT A P” is displayed on a TV screen. (Refer to Fig. 5.)
EJECT A R
Fig. 1
EJECT A T
Fig. 2
EJECT A C
Fig. 3
EJECT A D
Fig. 4
EJECT A P
Fig. 5
1-12-1
BLOCK DIAGRAMS <VCR SECTION>Servo / System Control Block Diagram
MLO
AD
ING
MO
TO
R
SE
NS
OR
CB
A
SE
NS
OR
CB
A
CA
PS
TA
N M
OT
OR
CO
NT
RO
LH
EA
D
CL5
04
CN
502
CN
504
AC
E H
EA
D A
SS
EM
BL
Y
MA
IN C
BA
KE
Y-
2
RF
-SW
C-F
G
C-C
ON
T
D-P
FG
ST
-S
T-R
EE
L
C-F
/R
KE
Y-
1
D-V
SY
NC
C-S
YN
C
V-E
NV
CT
L(+
)
RE
SE
T
C-R
OT
A
D-R
EC
-HD
-RE
C-H
D-R
EC
-H
RE
C-
SA
F-S
W
PG
-DE
LAY A
UD
IO-M
UT
E-H
AU
DIO
-MU
TE
-H
RF
-SW
D-V
SY
NC
C-S
YN
C
V-E
NV
C-R
OT
A
EN
D-S
IC50
1(S
ER
VO
/SY
ST
EM
CO
NT
RO
L)
4756
CT
L
SE
NS
OR
-SW
5863
CT
L(-)
57 284969 62 3 20 2765
1878641941
2
2476667
LM-F
WD
/RE
V21
D-C
ON
T29
(DE
CK
AS
SE
MB
LY
)
EN
D-S
T-R
EE
L
ST
-S
ST
-S
Q50
4
Q50
3
Q50
1
RE
SE
T
Q50
6
DV
D-R
EM
OT
E-I
NH
4
SW
-PO
INTA
L+5V
VR
501TIM
ER
+5V
TP50
6E
ND
-STP
507
P-O
N-L
22P
-ON
-L
P-O
N-C
ON
T27
P-O
N-C
ON
T
P-D
OW
N-H
1P
-DO
WN
-HH
-A-S
W79
H-A
-SW
H-A
-CO
MP
80H
-A-C
OM
P
46O
UTP
UT-
SELE
CT(
1)Y
CA
-SC
LY
CA
-SD
AY
CA
-CS
YC
A-S
CL
14Y
CA
-SD
A15
YC
A-C
S16
YC
A-S
CL
YC
A-S
DA
YC
A-C
S
SW
511
RE
C S
W
TO
VID
EO
B
LOC
K D
IAG
RA
M
TO
AU
DIO
B
LOC
K D
IAG
RA
M
LD-S
W68
AL+
12V
AL+
5V
AL+
5VS
W51
2
AL+
12V
AL+
18V
P-O
N+
5VLD-S
W
AL+
5V
Q11
06
D55
5S
-LE
D
TO
PO
WE
R
SU
PP
LY
BLO
CK
DIA
GR
AM
KE
YS
WIT
CH
KE
YS
WIT
CH T
P50
2S
-IN
H
5C
TL(
+)
6C
TL(
-)
1A
L+12
V2
P-O
N+
5V3
C-F
G4
C-F
/R
5C
-CO
NT
6G
ND
7LM
-FW
D/R
EV
8D
-CO
NT
9D
-PF
G
10G
ND
11A
L+12
V
12A
L+18
V
TP51
3C
TL
OU
TP
UT
-SE
LEC
T(1
)
OU
TP
UT
-SE
LEC
T(1
)
DV
D-P
OW
ER
DV
D-P
OW
ER
26
RE
MO
TE
-VID
EO
5
CY
LIN
DE
R A
SS
EM
BL
Y
DR
UM
MO
TO
R
PG
SE
NS
OR
M
M
CA
PS
TA
NM
OT
OR
MO
TO
RD
RIV
EC
IRC
UIT
TO
DV
D S
YS
TE
MC
ON
TR
OL
/SE
RV
O
BLO
CK
DIA
GR
AM
<D
VD
SE
CT
ION
>
TIM
ER
-LE
D-L
TIM
ER
-LE
D-L
D56
7D
VD
D56
6V
CR
D56
4T
IME
R
D56
5R
EC
AL+
5V
RE
C-L
ED
-L
VC
R-L
ED
-LV
CR
-LE
D-L
DV
D-L
ED
-LD
VD
-LE
D-L
75
RE
C-L
ED
-L74
PO
WE
R-L
ED
11
PO
WE
R-L
ED
10 7776 7170 7372
RE
MO
TE
-VID
EO
DV
D-R
EM
OT
E-I
NH
PO
WE
R
CN
508
CN
509
D56
1
PO
WE
RS
W51
8
33
KE
Y-1
11
PO
WE
R-L
ED
22
PO
WE
R-L
ED
PO
WE
R S
W C
BA
AL+
5V
AU
DIO
-MU
TE
-H
TO
Hi-F
i AU
DIO
B
LOC
K
DIA
GR
AM
IIC-B
US
SC
LIIC
-BU
S S
DA
1213IIC
-BU
S S
CL
IIC-B
US
SD
A
NO
RM
AL-
L59
Hi-F
i-H-S
W
Hi-F
i/NO
R-I
NH
i-Fi-H
-SW
25
E8E6EBLS
1-12-2
Video Block Diagram
MA
IN C
BA
Q39
1V
CR
DV
D
OU
TPU
T-S
ELE
CT(
1)
TP
751
V-O
UT
WF
1
BU
FF
ER
SW
CT
L
IC75
1(O
UT
PU
T S
ELE
CT
)
151 2
910
11
TO
SE
RV
O/S
YS
TE
M
CO
NT
RO
L B
LOC
K
DIA
GR
AM
DV
D-V
IDE
OT
O
DV
D V
IDE
O/A
UD
IOB
LOC
K D
IAG
RA
M<
DV
D S
EC
TIO
N>
OS
D C
HA
RA
CT
ER
MIX
38
40
IC50
1(O
SD
)
LUM
INA
NC
ES
IGN
AL
PR
OC
ES
S
VID
EO
(R
)-1
HE
AD
VID
EO
(L)
-1 H
EA
D
(D
EC
K A
SS
EM
BL
Y)
VID
EO(R
)-1VI
DEO
-CO
MVI
DEO
(L)-1
CN
253
1 2 3VI
DEO
(L)-2
VID
EO-C
OM
VID
EO(R
)-2
4 5 6
VID
EO
AG
CF
RO
NT
RE
AR
RP
R P
SY
NC
SE
PA
FB
C
Y/C
MIX
R P
YN
R/C
OM
B F
ILT
ER
CH
RO
MIN
AN
CE
SIG
NA
L P
RO
CE
SS
IC30
1(V
IDE
O S
IGN
AL
PR
OC
ES
S/ H
EA
D A
MP
)26
57
3028
QV
/QH
6dB
AM
P
TO
SE
RV
O/S
YS
TE
MC
ON
TR
OL
BLO
CK
D
IAG
RA
M
TO
SE
RV
O/S
YS
TE
MC
ON
TR
OL
BLO
CK
D
IAG
RA
MC
YL
IND
ER
AS
SE
MB
LY
RF
-SW
RF
-SW
59V
-EN
VH
-A-S
WH
-A-C
OM
PH
-A-C
OM
P
TP30
2
VID
EO
(L)
-2 H
EA
D
VID
EO
(R
)-2
HE
AD
TP
301
C-P
B
D-V
SY
NC
C-S
YN
C
D-V
SY
NC
2553 24
YC
A-S
CL
14
58 60
SP
EP
54Y
CA
-SD
A
55Y
CA
-CS
SE
RIA
LI/F
69 70
SP
HE
AD
AM
P
EP
HE
AD
AM
P
727374 656667
EN
V-D
ET
C-R
OT
A
C-R
OT
A/R
F-S
W
WF
2
WF
3
JK75
3V
IDE
O
-IN
2
JK75
2V
IDE
O
-IN
1
FR
ON
T
RE
AR
JK75
1V
IDE
O
-OU
TR
EA
RW
F6
J785
RE
C V
IDE
O S
IGN
AL
P
B V
IDE
O S
IGN
AL
DV
D V
IDE
O S
IGN
AL
M
od
e: S
P/R
EC
Q13
01IC
1801
(CC
D)
36
19
34
VC
A
AD
CD
AC
FIF
O
CLA
MP
BU
FF
ER
E8E6EBLV
1-12-3
Audio Block Diagram
OU
TP
UT-
SE
LEC
T(1
)
RE
CA
MP
SE
RIA
LI/F
98
AU
TOB
IAS
11
P-O
N+
5V
P-O
N+
5V
Q42
1
BIA
SO
SC
Q42
2
Q42
6 (P
B=
ON
) Q42
5S
WIT
CH
ING
D-R
EC
OF
F
6E
QA
MP
LIN
EA
MP
MU
TE
LPF
10
SP
/LP
-ON
P
RALC
7680
78
4AU
DIO
-PB/
REC
CN
504
3A
-CO
M1
AE
-H2
AE
-H/F
E-H
AU
DIO
HE
AD
AU
DIO
ER
AS
EH
EA
DAC
E H
EA
D A
SS
EM
BL
Y
FE
HE
AD
(DE
CK
AS
SE
MB
LY
)
1F
E-H
2F
E-H
-GN
D
CN
501
MA
IN C
BA
5855
5354
D-R
EC
-HA
UD
IO-M
UT
E-H
TO SE
RV
O/S
YS
TE
M
CO
NT
RO
L B
LOC
KD
IAG
RA
M
FU
LLE
RA
SE
HE
AD
YC
A-C
SY
CA
-SC
LY
CA
-SD
A
TO
DV
D V
IDE
O/A
UD
IO
BLO
CK
DIA
GR
AM
<D
VD
SE
CT
ION
>
FR
ON
T
RE
AR
DV
D-A
UD
IO(L
)D
VD
-AU
DIO
(R)
32
4
5
TP
753
A-O
UT
(R
)
TP
754
A-O
UT
(L)
JK75
1
AU
DIO
(R)
-OU
T1
AU
DIO
(L)
-OU
T1
JK75
6
AU
DIO
(R)
-OU
T2
AU
DIO
(L)
-OU
T2
TO S
ER
VO
/SY
ST
EM
CO
NTO
L B
LOC
KD
IAG
RA
MA
UD
IO S
IGN
AL
PR
OC
ES
S
IC30
1
IC75
1(O
UT
PU
T S
ELE
CT
)
SW
CT
LDV
D DV
DV
CR
/LIN
E
VC
R/L
INE
910
11
5 3 12 13144
AU
DIO
(R)-
IN-F
AU
DIO
(L)-
IN-F
AU
DIO
(L)-
IN
AU
DIO
(R)-
IN
AU
DIO
(R)-
OU
T
AU
DIO
(L)-
OU
T
N-A
-OU
TN
-A-I
N
TO H
i-Fi A
UD
IOB
LOC
K D
IAG
RA
M
JK75
2
AU
DIO
(R)
-IN
1
AU
DIO
(L)
-IN
1
JK75
4A
UD
IO(L
) -I
N2
JK75
5A
UD
IO(R
) -I
N2
PB
AU
DIO
SIG
NA
LR
EC
AU
DIO
SIG
NA
LM
od
e :
SP
/RE
CD
VD
AU
DIO
SIG
NA
L
E8E6EBLA
1-12-4
Hi-Fi Audio Block Diagram
E8E6EBLH
RE
C A
UD
IO S
IGN
AL
PB
AU
DIO
SIG
NA
LM
od
e :
SP
/RE
C
TO
S
ER
VO
/SY
ST
EM
CO
NT
RO
L B
LOC
K
DIA
GR
AM
9 10 61
INP
UT
SW
R-C
H
INP
UT
SW
L-C
H
NO
RS
W
MU
TE
SE
RIA
LD
AT
AD
EC
OD
ER
L-C
H H
i-Fi
AU
DIO
SIG
NA
L P
RO
CE
SS
R-C
H H
i-Fi
AU
DIO
SIG
NA
L P
RO
CE
SS
MT
S/S
AP
S
IGN
AL
PR
OC
ES
S
OU
TP
UT
SW
R-C
H
OU
TP
UT
SW
L-C
H
dBX
D
EC
MU
TE
C
ON
TR
OL
MA
TR
IXE
NV
D
ET
MU
TE
AM
P
62 53 5743 42 21 222930 24
AU
DIO
(R)-
IN
AU
DIO
(L)-
IN
N-A
-OU
T
AU
DIO
(L)-
OU
T
AU
DIO
(R)-
OU
T
N-A
-IN
Hi-F
i-H-S
W
AU
DIO
-MU
TE
-H
D-R
EC
-H
NO
RM
AL-
L
TO
AU
DIO
B
LOC
K D
IAG
RA
M
IIC-B
US
SD
AIIC
-BU
S S
CL
MA
IN C
BA
Hi-F
i-AU
DIO
(R)
7H
i-Fi-C
OM
8H
i-Fi-A
UD
IO(L
)9
CN
253
IC45
1(H
i-Fi A
UD
IO P
RO
CE
SS
/ Hi-F
i HE
AD
AM
P)
AU
DIO
(R)-
IN-F
AU
DIO
(L)-
IN-F
TO
AU
DIO
B
LOC
K
DIA
GR
AM
TO
S
ER
VO
/SY
ST
EM
CO
NT
RO
L B
LOC
K
DIA
GR
AM H
i-Fi
AU
DIO
(R)
HE
AD
Hi-F
iA
UD
IO(L
) H
EA
D
CY
LIN
DE
RA
SS
EM
BL
Y
(DE
CK
AS
SE
MB
LY
)
DR
IVE
Q43
0 Q42
9
Q43
2
Q42
8
MU
TE
MU
TE
INV
ER
TE
R
14 15
28 3627
1-12-5
Power Supply Block Diagram
7 8
1 234IC
1001
ER
RO
RV
OLT
AG
E D
ET
T10
01
Q05
5
Q05
2
Q05
6
MA
IN C
BA
HO
T C
IRC
UIT
. BE
CA
RE
FU
L.
20 19 18 17 16 15 14 13 12 11
Q10
06
Q10
05
Q11
01
Q10
11
1E
V+
1.2V
2E
V+
1.2V
3E
V+
3.3V
4E
V+
3.3V
5E
V+
3.3V
7D
VD
-P-O
N+
5V8
EV
+11
V9
EV
+11
V6
DV
D-P
-ON
+3.3
V17
PW
RC
ON
IC10
04+
3.3V
RE
G.
IC10
02+
1.2V
RE
G.
CN
1001
Q10
04
P-O
N+
5V
DV
D-P
-ON
+12V
AL+
18V
EV
+3.
3V
P-O
N+
9V
AL-
30V
AL+
12V
TIM
ER
+5V
AL+
5V
DV
D-P
-ON
+5V
DV
D-P
-ON
+3.3
V
TO
DV
D M
AIN
CB
A U
NIT
CN
401
TO
S
ER
VO
/SY
ST
EM
CO
NT
RO
L B
LOC
K D
IAG
RA
M
P-O
N-L
P-D
OW
N-H
Q06
3
Q06
4
P-O
N-C
ON
T
HO
TC
OL
D
2 4
IC10
03( S
WIT
CHIN
G C
ONT
ROL)
Q10
02
VD
D
AC
1001
F10
021.
6A 2
50V
LIN
EF
ILT
ER
L100
1
A
V
F
D10
01 -
D10
04
BR
IDG
ER
EC
TIF
IER
SW
ITC
HIN
GC
ON
TR
OL
5
2
6
1 3
AC
CO
RD
SW
+9V S
W+
12V
SW
+5V
SW
+5V
SW
+3.
3V
SW
+5V
CA
UT
ION
!F
ixed
vol
tage
(or
Aut
o vo
ltage
sel
ecta
ble)
pow
er s
uppl
y ci
rcui
t is
used
in th
is u
nit.
If M
ain
Fus
e (F
1002
) is
blo
wn
, che
ck to
see
that
all
com
pone
nts
in th
e po
wer
sup
ply
circ
uit a
re n
ot d
efec
tive
befo
re y
ou c
onne
ct th
e A
C p
lug
to th
e A
C p
ower
sup
ply.
O
ther
wis
e it
may
cau
se s
ome
com
pone
nts
in th
e po
wer
sup
ply
circ
uit t
o fa
il.
NO
TE
:T
he v
olta
ge fo
r pa
rts
in h
ot c
ircui
t is
mea
sure
d us
ing
hot G
ND
as
a co
mm
on te
rmin
al.
"Ce
sym
bole
rep
rèse
nte
un fu
sibl
e à
fusi
on r
apid
e."
CA
UT
ION
!F
or c
ontin
ued
prot
ectio
n ag
ains
t fire
haz
ard,
repl
ace
only
with
the
sam
e ty
pe fu
se.
AT
TE
NT
ION
: P
our
une
prot
ectio
n co
ntin
ue le
s ris
qes
d'In
cele
n'u
tilis
er q
ue d
es fu
sibl
e de
mêm
e ty
pe.
Ris
k o
f fi
re-r
epla
ce fu
se a
s m
arke
d."T
his
sym
bol m
eans
fast
ope
ratin
g fu
se."
A
V
F
E8E6EBLP
1-12-6
BLOCK DIAGRAMS <DVD SECTION>
E8E6EBLSD
DVD System Control / Servo Block Diagram
MA
IN C
BA
RE
MO
TE
SE
NS
OR
RM
2001
SK
IP-D
OW
N19
22
PLA
Y20
23
RE
MO
TE
2225
DIS
CIN
-L21
24S
KIP
-UP
1821
DVD-
OPEN
/CLO
SE24
27D
VD
-PO
WE
R23
26D
VD
-STO
P26
29D
VD
-PLA
Y25
28
TO S
ER
VO
/SY
ST
EM
CO
NT
RO
L B
LOC
K
DIA
GR
AM
<V
CR
SE
CT
ION
>
DV
D-P
OW
ER
CN
401
CN
1001
DV
D-P
LAY
DV
D-S
TOP
DV
D-P
OW
ER
DV
D-O
PE
N/C
LOS
E
Q20
02Q
2013
Q20
14
EV
+3.
3V
AL+
5V
EV
+3.
3V
D20
01D
2002
PLA
Y
SW
2001
CN
2002
CN
2003
DV
D-O
PE
N/C
LOS
E
1E
V+
3.3V
12
DVD-
OPEN
/CLO
SE2D
VD
OP
EN
/CL
OS
E C
BA
SW
2002
STO
P
SW
2005
SK
IP-U
P
SW
2006
SK
IP-D
OW
N
SW
2003
PLA
Y
78 80 77 79 56D
ISC
IN-L
54S
KIP
-DO
WN
53S
KIP
-UP
49R
EM
OT
E55
PLA
Y
DV
D M
AIN
CB
A U
NIT
DR
IVE
CB
A
IC30
1(S
ER
VO
DR
IVE
)
CN
301
M
SLE
D
MO
TO
R
M
SP
IND
LE
MO
TO
R
IC10
1(M
ICR
O C
ON
TR
OLL
ER
)
+ -+ -
+ -+ -
+ -+ - + -
SLE
D
MO
TOR
DR
IVE
FO
CU
SA
CT
UAT
OR
DR
IVE
SP
IND
LE
MO
TOR
DR
IVE
TR
AC
KIN
GA
CT
UAT
OR
DR
IVE
126
TR
AY-I
N
SLE
D D
RIV
E67
SP
IND
LE
DR
IVE
66
TRAC
KIN
GD
RIV
E
127
FO
CU
S D
RIV
E
65
TO D
IGIT
AL
SIG
NA
L P
RO
CE
SS
BLO
CK
D
IAG
RA
M
FS
(+)
FS
(-)
TS
(+)
TS
(-)
TO D
VD
V
IDE
O/ A
UD
IOB
LOC
K D
IAG
RA
MI/P
-SW
I/P-S
W
TR
AY-I
N
1S
P(+
)2
SP
(-)
6T
RA
Y-I
N3
GN
D4
SL(
-)5
SL(
+)
VR
EF
RE
SE
T7047
+3.
3V
IC30
2(O
P A
MP
)
15 16 14 13 12 11 17 182364 531 225 2427 26
63S
L-A
MP
121
SP
-RO
T
+3.
3V
12 6
753 9
810
122
SL-
AD
S
RE
SE
T
IC46
1
21
RE
MO
TE
-VID
EO
DV
D-R
EM
OT
E-I
NH
DIS
C-I
N
1-12-7 E8E6EBLD
Digital Signal Process Block Diagram
C16
D18
A17
B15
DV
D-L
D8
CD
-LD
10
PD
-MO
NI
7
FS
(+)
2F
S(-
)3
TS
(+)
1T
S(-
)4C
N20
1
CN
201
CN
201
IC10
1(D
IGIT
AL
SIG
NA
L P
RO
CE
SS
)
FS
FS
(+)
CD
/DV
D
FS
(-)
TS
(+)
TS
(-)
TS
DE
TE
CTO
R
CD
/DV
D19
Q25
1,Q
252
AM
P
Q25
3,Q
254
AM
P
GN
D(D
VD-P
D)
6G
ND
(CD
-PD
)5
GN
D(L
D)
9
RF
SIG
NA
LP
RO
CE
SS
AU
DIO
I/F
VID
EO
I/FV
IDE
OE
NC
OD
ER
SD
RA
M
100
115
116
113
114
106
104
103
105
62
152
151
146
144
IC10
3(F
LAS
H R
OM
)
FLA
SH
RO
M
FD
Q (
0-15
)
FAD
R(0
-19)
SD
RA
M D
ATA
(0-1
5)
PIC
K-U
PU
NIT
TO D
VD
SY
ST
EM
C
ON
TR
OL/
SE
RV
OB
LOC
K D
IAG
RA
M
DV
D M
AIN
CB
A U
NIT
IC50
1(S
DR
AM
)
SD
RA
M D
ATA
(0-1
5)
SD
RA
M A
DD
RE
SS
(0-1
0)
2 12 39 49
~ ~
20 24 27 32
~ ~
159
178~
99 98 97
1~4
1718
215
216
7~14
21
~30
212
34~
42
1 9 2516 48~ ~ 29 36 4538~ ~
DIG
ITA
LS
IGN
AL
PR
OC
ES
S
EXT MEMORY DATA(0-15)
EXT MEMORY ADDRESS(0-19)
SD
RA
M A
DD
RE
SS
(0-1
0)
D/A
D/A
131
139
Y(I/P
) C
VID
EO
-Y(I
/P)
VID
EO
-C
D/A
129
Pr/C
rV
IDE
O-P
r/Cr
D/A
130
Pb/C
bVI
DEO
-Pb/
Cb
D/A
138
SP
DIF
DVD-
AUDI
O-M
UTE
DV
D-A
UD
IO(R
)
DV
D-A
UD
IO(L
)
TO D
VD
V
IDE
O/A
UD
IOB
LOC
K
DIA
GR
AM
DV
D A
UD
IO S
IGN
AL
DV
D V
IDE
O S
IGN
AL
IC20
1(S
W)
41
6
3
198
203~
194
206
209~
1-12-8 E8E6EBLVD
DVD Video / Audio Block Diagram
DIG
ITA
LA
UD
IO O
UT
JK12
02 (
RE
AR
)B
UF
FE
RQ
1351
IC12
01
Q12
01
Q12
02
DV
D-P
-ON
+5V
(AM
P)
CN
601
CN
1601
76 2
13
DV
D A
UD
IO S
IGN
AL
EV
+3.
3VQ12
04
5
CN
601 8
8V
IDE
O-Y
(I/P
)10
10V
IDE
O-C
66
VID
EO
-Pb/
Cb
44
VID
EO
-Pr/
Cr
JK14
01 (
RE
AR
)S
-VID
EO
OU
T
CN
1601
IC14
02(V
IDE
O D
RIV
ER
)
134d
BA
MP
2dB
AM
PLP
FD
RIV
ER
114d
BA
MP
2dB
AM
PLP
FD
RIV
ER
6
104d
BA
MP
2dB
AM
PLP
FD
RIV
ER
83
5
DV
D V
IDE
O S
IGN
AL
VID
EO
-Y(I
/P)
VID
EO
-CV
IDE
O-P
b/C
b
VID
EO
-Pr/
Cr
DV
D-V
IDE
O
WF
9
WF
7
WF
8
WF
4
1212
DVD
-AU
DIO
(L)
1414
DVD
-AU
DIO
(R)
1313
DVD-
AUDI
O-MU
TE
1616
SP
DIF
DV
D-A
UD
IO(L
)
DV
D-A
UD
IO(R
)
22
I/P-S
W
I/P-S
WW
F5
VID
EO
-Pb/
Cb
OU
T
VID
EO
-YO
UT
VID
EO
-Pr/
Cr
OU
T
JK14
03
TO D
VD
SY
ST
EM
C
ON
TR
OL
/ SE
RV
O
BLO
CK
DIA
GR
AM
TO D
IGIT
AL
SIG
NA
L P
RO
CE
SS
BLO
CK
DIA
GR
AM
MA
IN C
BA
DV
D M
AIN
CB
A U
NIT
TO A
UD
IOB
LOC
K D
IAG
RA
M<
VC
R S
EC
TIO
N>
TO V
IDE
OB
LOC
K D
IAG
RA
M<
VC
R S
EC
TIO
N>
(RE
AR
)
154d
BA
MP
2dB
AM
PLP
FD
RIV
ER
1
142d
BA
MP
DR
IVE
R
SP
DIF
DV
D-A
UD
IO(L
)TO
DIG
ITA
LS
IGN
AL
PR
OC
ES
SB
LOC
K D
IAG
RA
MD
VD
-AU
DIO
(R)
DV
D-A
UD
IO-M
UT
E
GG
YC
1-13-1 DL8N_SC
SCHEMATIC DIAGRAMS / CBA AND TEST POINTS
Standard Notes
WARNING
Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by the mark “#” in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards.
Notes:1. Do not use the part number shown on these
drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared.
2. All resistance values are indicated in ohms (K = 103, M = 106).
3. Resistor wattages are 1/4W or 1/6W unless otherwise specified.
4. All capacitance values are indicated in µF (P = 10-6 µF).
5. All voltages are DC voltages unless otherwise specified.
1-13-2 DL8N_SC
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES:
1. CAUTION:
FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQES D'INCELE N'UTILISER QUE DES FUSIBLE DE MÊME TYPE. RISK OF FIRE-REPLACE FUSE AS MARKED.
2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F1002) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
3. Note:1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
2. To maintain original function and reliability of repaired units, use only original replacement parts which are listed with their part numbers in the parts list section of the service manual.
4. Voltage indications on the schematics are as shown below:
5. How to read converged lines
6. Test Point Information
A V
F
This symbol means fast operating fuse.Ce symbole represente un fusible a fusion rapide.
2 31 5.0(2.5)< 0 >
PLAY mode REC mode DVD mode
5.0
The same voltage forboth PLAY, REC & DVD modes
Indicates that the voltageis not consistent here.
Unit: Volts
3
2
1
A B C D
1-B1
1-D3
AREA D3
AREA B1
1-D3
Distinction AreaLine Number (1 to 3 digits)
Examples:1. "1-D3" means that line number "1" goes to the line number "1" of the area "D3". 2. "1-B1" means that line number "1" goes to the line number "1" of the area "B1".
: Indicates a test point with a jumper wire across a hole in the PCB.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.
1-13-3
Main 1/8 Schematic Diagram < VCR Section >
E8E6ESCM1
1-13-4
Main 2/8, Power SW & Sensor Schematic Diagram < VCR Section >
E8E6ESCM2
1-13-5
Main 3/8 Schematic Diagram < VCR Section >
E8E6ESCM3
1-13-6
Main 4/8 Schematic Diagram < VCR Section >
E8E6ESCM4
1-13-7
Main 5/8 Schematic Diagram < VCR Section >
E8E6ESCM5
1-13-8
Main 6/8 & DVD Open/Close Schematic Diagram < VCR Section >
E8E6ESCM6
1-13-9
Main 7/8 Schematic Diagram < VCR Section >
E8E6ESCM7
CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F1002) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
"Ce symbole reprèsente un fusible à fusion rapide."
CAUTION !For continued protection against fire hazard,replace only with the same type fuse.ATTENTION : Pour une protection continue les risqesd'Incele n'utiliser que des fusible de même type.Risk of fire-replace fuse as marked.
"This symbol means fast operating fuse."
A V
F
1-13-10
Main 8/8 Schematic Diagram < VCR Section >
E8E6ESCM8
1-13-11 E8E6ESCD1
DVD Main 1/3 Schematic Diagram < DVD Section >
1-13-12 E8E6ESCD2
DVD Main 2/3 Schematic Diagram < DVD Section >
1-13-13 E8E6ESCD3
DVD Main 3/3 Schematic Diagram < DVD Section >
1-13-14
J535J773
J776
J795
J796
J797
J799
Q761
Q762
J37
J46
C764
C765
C775
C778
C779
C780
C781
J798
IC771
LINE-IN-L
GND
LINE-IN-R GND
4
5
A
G FPb
J124J156
J774
J785
J787
J789
L771
J41
R774
R777
R778
R788
C757
C774
C782
J118
J122
J123
J112
J807
IC752
IC751
J120
J125
J157
ALL+
5V
DVD-A-L
LINE-OUT-R
VIDEO-OUTSYS
GND
DVD-A-L
VIDEO-OUTSYS
BUFF
ER+9
V
GND
DVD-A-R
GND
VIDEO-OUTSYS
J538
J551
J552
TP507
C057
C448
C449C477
C479
C481
C490C498
Q771
J051
J25
J26
J28
J44
R785
R786
C776
C777
L051
N-A-OUT
P-ON+9V
GND
ALL+5VGND
GND
GND
N-A-INHIFI
3
J531
J532
J533
J534
J536
J537
J183 J184
C438
C439
C441 C451
C452
C455
C480
C482
C483
C493
C494
J451
C311
J99
J104
J106
J114
C453
LINE-IN-LF
LINE-OUT-L
LINE-OUT-R
GNDV-IN
REAR
OUTPUTMUTE
LINE-IN-L
DVD-A-R
L452
J541
J545
J546
J547
J548
J549
J550
J553
TP301
TP302
TP505
TP513
Q503
C468
C471
C472
C474
C475
C476
J09
J16
J24
J35
C313
J57
J60
IC451
J54
C473
CTL
T-REEL
C-PB
RF-SW
HIFI-ENV
H-A-
SW
GND
YCA-CS
P-ON+5V
RF-SW
A-MUTE
IIC-BAS-CLK
IIC-BAS-DATAPG-Delay
GND
V-IN-F
LINE-IN-LF
LINE-IN-RF
GND
P-ON+5V
H-A-COMP
P-DOWN-H
RF-SW
D-Vs
ync
HIFI-H-SW
2
L451
J542
C406
C440
C454
C456
C457
C458
C464
C466
C478
D451
R542
C327
C328
C330
C332
C334
C343
J94
J95
L251
X301IC1801
IC301L3
03
J1301
J1302
J823
J554
3.58MHZ
GND
VIDEO-OUTYCA
GND
VIDEO-OUTSYS
LM-FBR
YCA-
CLK
NORM
AL-L
D-REC
V-ENV
SENSOR-SW
YCA-
DATA
DVD-POWER-H
GND
C-SYNC
F
P b
G
D561
SW518
CN508
D562
D563
SW519
SW-POINT
J520
J540
J543
J544
J370
J380
C053
C055
Q501
L506
SW511
J03
J04
J05
J06
J07
J08
J11
J12
J13
J14
CN509
C503
C505
C507
J56
VR501 J65
J67
J69
J72
J79
R580
J85
IC505
J383
J558
POWER
SWITCH
PCB
POWER
BE8E6DF0101 1 B
ALL+5VSYS
TIMER+5V
ALL+5VSYS
TIMER+5V
ALL+5V
GND
IIC-BAS-DATA
T-REELOUTPUTMUTE
D-REC
GND
1
D564D565
J134
J136
R609
J143
J144
J151
J388
PS502
C509
X501
X502
C524
J77
J81
J82
J84
J86
J88
J89
J91
R596
D501
J501
J382
J147
J149
J148
IC501
J87
J539
J371
J560
J133
J138
J559
J511
J152
J132
J155
RESE
T
ALL+5VSYS
ALL+5VSYS
TIMER+5V
DISP-ENA
DISP-DATA
DISP-CLK
REMOTE-VIDEO
REC-SAF-SW
ALL+5V
PON-CONT
POW-LED DVD-REMOCON-INH
C-F/R
C-CONT
P-ON-L
DVD-REMOCON-INH
D571
SW501SW515 SW516
R528
JK753 JK754 JK755
R566
REW
P-ON+5V
A B
SW505SW508 SW509
C502
R568
FF STOP PLAY REC
REC
TIMER
GND
C
J131
J130
FIP502
R607
J161
J386
R529
C2004
R555
R556
C550
C551
RM2001
C572
IC571
R554
L2001
J821
J175
J159
J259
J261
J263
J258
R1105
R110
7
R111
2
R1106
J561
J500
J265
J164
J256
J163
J564
J565
VCR-TIMER-LED
VCR-REC-LED
ST-S
LD-SW
VCR-LED
REMOTE-DVD
ALL+5V
GND GN
D
GND
EV+3
.3V
DVD-LED PON-
CONT
D
E
J355
J172
Q506
L504
SW512
J231
J232
J234
J236
C516
C519
C530
C531C5
32
C533
C535
J304
D555
J173
J237 L751
J165
J171
J168
J503
J246
J248
J381
J243J176
J167
J356
J242
J562
R531
J166
J241
R095
J170
J251
J249
J252
R092
J563
ALL+5VSYS
ALL+5VSYS
DVD-P-ON+12V
ALL+18V-VG
D-PFG
DVD-P-ON+5V
OUTPUTSEL1
OUTPUTSEL2
DUBBING-INH
ALL+5V
ALL+
20V
P-ON+5V
CTL-
CTL+
GND
OUTPUTSEL1
VIDEO-OUTSYS
GND12
VCAP
P-ON+5V
12VCAP
EV+3.3V
GND
F2
GND
ALL+5V
ALL-
30V
PON-CONT
R426
R428C409
J750
J177
J178
J179
J182
J186
J191
J195
L304
J218
J219
J802
J226
J227
J229
J233
C308
C310
C350
J115
L301
J221
J174
J811
C301
J224
J805
J228 J801
J185
GND
VINF
1
VIDEO-OUTYCA
C-SYNC
D-Vs
ync
VINR1GND
A-PB/REC
GND
VIDE
O+5V
ALL+5V
CCD+3V3
CCD+
3V3
GND
P-ON+5V
D-REC
GND
P-ON
+5V
R421
R424
R425
C405
C412
C423
C424
J198
R1395
J203C1201
Q120
4
C1221
C1222 C1247
C1249
R124
5Q4
21
Q422
Q425
L421
C422
C425
IC1201
J105
J100
J814
D1058
J193 J2
02
J127
J359
J129
J808
J809
C120
2
J504
J567
AVPCB
EV+3.3V
LINE-IN-L
N-A-
IN
GND
GND
DVD-P-ON+5V
GNDGN
D
P-ON
+5V
N-A-IN
J395
J793
TP753
TP75
4
J206
J208
J209
J211
Q391
C1443
JK75
2
C1462
R758
C1482
R391
R392
R794
C391
C392
J810J566
AUDIO-R
AUDIO-L
V-21 A
BE8E6DF0101
BUFF
ER+9
V
P-ON
+9V
DVD-P-ON+5V
BE8E6DF01011
18
1
C152
2
C152
4
C1532
L1007
C1536
C020
L1020
TP75
1
L502
C1007
J212
J213
C1014
C1015
J216
J217
C1038
C1442
C1461
L152
2
C1481 J1002
J317
J373
IC1402
IC14
03
CN16
01J214
J314
D1016
C1018
C1019
D1008
D1020
V-OUT
GND
C
GND GND
L750 C1
352
C136
1
C041
J397
JK12
02
JK14
01
JK1403
T1001
Q1201
Q1202 IC1001
IC12
04
JK75
1 JK75
6
C772
C773
L1350
Q1002J1003
R1014
C1011
D1012
D1006
J1001
D041
L1002
Q1351
GND
HOT
AC1001
L1001
C013
D037
C1002
C1023
D1010
L009
J387
D015
D016
D013
C014
D019
C1004
R1013
C1013
C1012
BC1001
C1001
SA1001
D1014
D1011
GND
1
C023
R073
D062
D1001
D1002
D1003
D1004
C1030
C1031
C1039
C1040
R1026
C1051D1031
D1037
D1038
R1035
F1002
J282
R1068 R1077
Q063
Q064
D082
R066
D063
CN1001
J289
J817
J812
J296
D080
RISK OF FIRE-REPLACE FUSE AS MARKED.
J281
C1003
J3001 J557
D1036
C1082
T1.6A L 250V
COLD
GND
ALL-
30V
GND
ALL+
12V
12VCAP
GND
GND
FG
28
CN2002
SW502
Q1004
Q1006
C1042R1025
CN2003
C1072
SW2002 SW2003SW2006
D2001
D2002
R573
R574
R2051
R2053 R2054
R2052
J284
R547
R521
J286
R522J820
SW2005
OP/CL
PCB
OUTPUT
VCRDVD
SKIP-DOWN STOP PLAY SKIP-UP
P-SCAN PLAY
GND
EV+3
.3V
GND
GTP502
SW513
SW514
J822
J269
R111
3
CH-DOWN CH-UP
S-INH
OUTPUTSEL1
GND
F
Joints
Pb
SW2001BE8E6DF01011 C
Pb
D566 D567
R063
J393
D052
J271
J272
J275
J277
J278
Q055
Q056
J305
R532
J399
DVD-P-ON+5V
DVD-P-ON+3.3V
ALL+4.0V
ALL+2.8V
ALL+5V
GND
GND
C545
R056
C021
R075
C051
R533
R534
R535
R536 Q052
J301
J307
J506 J508
J299
J315
J247
J302
J306
J295
ALL+12V
GND
P-ON+5V
P-ON+9V
P-ON-L
GND
GND
GNDGND
GND
C018
TP506
Q504R1030
C521
C544
J309
J333 J120
1
J1202
P-ON+5V
EV+3.3V
ALL+5V
DIP1 2 3 4 5 6 7 8 9
SW-POINTVR501
CTLTP513
C-PBTP301WF3
RF-SWTP302WF2
S-INH
TP502
V-OUTTP751WF1
BE8E6DF01011
CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F1002) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
"Ce symbole reprèsente un fusible à fusion rapide."
CAUTION !For continued protection against fire hazard,replace only with the same type fuse.ATTENTION : Pour une protection continue les risqesd'Incele n'utiliser que des fusible de même type.Risk of fire-replace fuse as marked.
"This symbol means fast operating fuse."
A V
FBecause a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing.Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required.
Main CBA, Power SW CBA, DVD Open/Close CBA Top View
Power SW CBA
DVD Open/Close CBA
Sensor CBA Top View
BHF300F01012A
BHF300F01012BMain CBA
1-13-15
123456789
R042C1350
C1351C1353
C1354
C1355
C1356
C1358C1359
C1362
R1351
R1352
R1353
R1354
R1355
R1356
R1364 C1223
C1224
R1422
L1351
GND
C1005 C1006
Q1001
C1010
C1008
D1007
D1009
D1013
R1003
R1001
R1004
R1005
R1006
R1007
R1010
IC1003
R1015R1009
R1008
D1005C1009
R1012
C1016
R067
JC14
D031
D035
C1049
C539
R068
JC806
JC807
R038
D030
R1011
R1016
ST-S
GND
ALL-30V
ALL+12V
GND
GND
P-ON-L
GND
GND
ALL+5V
GNDGND
GND
1
1
COLD
CN1001
IC1002
C1053
C1054C1070
R1085R1087
R1091
Q1005
Q1011
1
R1090
C1061
C1062
1
C1071 C3001
R3001R3002
Q3001Q3002
R1086
R30041
HOT
GND GND
GND
27P28P
26P
IC1004
C1052
R1044
Q2002
Q2013
28
R2001
R2056
R1052
R2003
R2055
R2012
R2013
R548
Q1101
R1051R2002
R1101
C1101
R1102
2726
GND
EV+3.3V
GND
F
PbJoints
G
P b
S-INH
R590
R591
R594
C563
Q3003
R3003
OUTPUTSEL1
GND
R069
SW2007
R564
C552
D1101
R057 DVD-P-ON+5V
DVD-P-ON+3.3V
ALL+4.0V
ALL+2.8V
ALL+5VALL+12V
12VCAP
P-ON+5V
P-ON+9V
GND
GND
R041
R046
C1535
JC22
CN1601
C1021
C1423
R1421
R1425
C1465
C1466
R1441
R1443
R1461R1481
R1482
R1490
R1226
R1403
R1399
R1225R045
R044
R043
D1017
15
10
5
13P14P15P16P
GND
GND
GND
13P14P15P16P
1
5
15
11
16 15 14 13
BE8E6DF01011
R1442
R752
R1462
C751
C752
5
4
R407R408
R414
C1531
C410
JC16
JC30
JC31
C1203
C1205C1206
C1207
C1208
R1207
R1208
R1209
IC1201
R1210
C1245
C1246
C1441
R1238R1240
R397
C415
R1205
C408R411
C407
R412
C414
R416R410R409
JC802
R406R405
C403
L400
R1206
JC804
EV+3.3V
LINE-IN-L
N-A-IN
DVD-A-L-MUTE
GND
BUFFER+9V
P-ON+9V
GND
DVD-P-ON+5V
GND
DVD-P-ON+5V
GND
P-ON+5V
R413
R415
R422
C1523
C1537
R1521
C411
R301
R302
R304R305
C1421
C1422
R1401
CN504
R331
R332
IC1402
IC1403
C304
C305
C306
C307C312C314
C315 C317
Q426
C
C302
R303
C303
R330C413
C352
C351 R341
R342
R345
C1403
VINR1
GND
A-PB/REC
GND
VIDEO+5V
EV+3.3V
R306
R511
Q1802
R518
CN502
R552
C518
C522
C523
C525
C527
C536
C546C547
D504
R344
Q1803
R343
R1110
Q1103
R1108
R1111
R1109
JC240
Q1105
Q1104
C1501
ALL+5VSYS
D-PFG
DVD-P-ON+5V
OUTPUTSEL1
GND
VINF1
VIDEO-OUTYCA
C-SYNC
D-Vsync
ALL+20V
ALL+5V
CCD+3V3
GND
P-ON+5V
D-REC
P-ON+5V
GND
CTL-
CTL+
P-ON+5V
GND
OUTPUTSEL1
VIDEO-OUTSYS
12VCAP
P-ON+5VEV+3.3V
GND
GND
ALL-30V
C541
14
15
2860
61
FIP502
R602
R603
IC571
R525
R526
R527 C501
C2002
R541
C2012
R2005
R572
R583
R2028
R2031
C560
C570
C571
C574
C575
C577
IC501
R2006
C581
R1103
Q1102
R1104C576
R600R553
R605
R540
JC501
R1501
Q2014
VCR-TIMER-LED
ST-S
LD-SW
DUBBING-INH
ALL+5V
VCR-LED
GND
REMOTE-DVD
ALL+5V GND
GND
GND
EV+3.3V
F2
ALL+5V
DVD-LED
PON-CONT
PON-CONT
20
21
80
R606
R608
R610R612
R617
R618
R619
R620
R625
R626 R502
R503
R504
C506
R543
C508
R545
R546
C517
R576
C542
R585R586R587R588
R593
C562
R550
R551
1
TIMER+5V
ALL+5VSYS
ALL+5VSYS
DISP-ENA
DISP-DATA
DISP-CLK
REMOTE-VIDEO
REC-SAF-SW
GND
ALL+5V
PON-CONT
POW-LED
GND
IIC-BAS-DATA
DVD-REMOCON-INH
4041
R611
JC11
L1801
L1802
R468C443
JC801
R307
R310R506
R507
R508
R316
C1801C1802
C1803C1804
R510
C1805
C1806
R512C1807
C1808
R517
C1810
R523R524
R1801
R1803
R538
R1805
R539
R1806
C510
C511
C512
C514C515
C326
R557
R559
C329
C520
R563
C528
C529
C534
C538
C345
R577
R578
C548
R315
R530
Q1106
R549
RESET
3.58MHZ
TIMER+5V
GND
VIDEO-OUTYCA
GND
VIDEO-OUTSYS
LM-FBR
YCA-CLK
D-REC
OUTPUTSEL2
SENSOR-SW
P-ON+5V
YCA-DATADVD-POWER-H
C-F/R
C-CONT
P-ON-L
GND
D-CONT
C-SYNC
C1811C1812
24 13
12
21
2061
60
4140
R1309
Q302
R308
R311
R317
R318 R319
R320
C1809
R325
R333
C309
IC1801
C316
C319
C322
C333
C336
C338C339C340
C341
C342
C348
IC301
Q1301
TP511
CCD+3V3
80
R401R402
R403R404
C401
C402
C404
JC03
JC05
R451
C416
R452
R453
R454
R455R456
CN253
R466R327
R1221 R1223
R792
C417
1
VIDEO-OUTSYS
N-A-IN
DVD-A-L
DVD-A-R
916
8
IC751
IC752
JC10
JC761
JC782R1222 R1224
R775
R780
C753
R793
C766
C1701
ALL+5V
DVD-A-L
LINE-OUT-R
GND
GND
GND
VIDEO-OUTSYS
169
D777
JC762
R474
JC781
JC786
JC788
R493
R773
JC48
LINE-IN-RF
LINE-OUT-L
LINE-OUT-R
N-A-OUT
GND
P-ON+9V
V-INREAR
OUTPUTMUTE
LINE-IN-L
GNDVIDEO-OUTSYSLINE-IN-L
LINE-IN-R
GND
DVD-A-R
VIDEO-OUTSYS
BUFFER+9V
IC771
R759
R761
R762
R763R764
R765
R766
R767R768
R781
R790
R791
R469 R471
R473
R476
R477
R481
R488
R490
C470
C486
C487
C488
C491
C496
C497
IC451
CN501
C321
R782
R783R784
Q428
Q429
Q430
Q432
GND
D100
D101
C711
GND
ALL+5V
GND
GND
GND
GND
1
JC06R450
R460
R461
R463
R464R465
R480R482
R483
R485
R486
C450
R491
C459
C460
C461
C462 C463
C465
C467
C331 R640
JC07
R458
R462
C430
R478
R479
C484
C485
R321
R323 R324
R544
C540HIFI-ENV
T-REEL
H-A-SW
GNDP-ON+5V
RF-SW
A-MUTE
IIC-BAS-CLK
IIC-BAS-DATA
P-ON+5V
PG-DelayGND
V-IN-F
LINE-IN-LF
LINE-IN-RF
P-ON+5V
H-A-COMP
P-DOWN-H
RF-SW
D-Vsync D-REC
HIFI-H-SW
C445
R322
R537
C504
C526
IC505ALL+5VSYS
TIMER+5V
ALL+5V
NORMAL-L
YCA-CS
V-ENV
T-REELOUTPUTMUTE
GND
F
P b
G
R058
R501
R753
C537
C760
C761
P-ON+5V
C763
PIN 8 OFCN1601
PIN 16 OFCN1601
PIN 12 OFCN1601
PIN 10 OFCN1601
PIN 14 OFCN1601
WF6WF5 WF4WF8 WF7 WF6WF7 WF5 WF4WF8WF9PIN 2 OFIC751
BE8E6DF01011
Main CBA, Power SW CBA, DVD Open/Close CBA Bottom View
Power SW CBA
Main CBA
DVD Open/Close CBA
CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F1002) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
"Ce symbole reprèsente un fusible à fusion rapide."
CAUTION !For continued protection against fire hazard,replace only with the same type fuse.ATTENTION : Pour une protection continue les risqesd'Incele n'utiliser que des fusible de même type.Risk of fire-replace fuse as marked.
"This symbol means fast operating fuse."
A V
FBecause a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing.Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required.
WAVEFORMS
WF1
WF3
WF1 UPPER
WF2
WF2
LOWER
TP751
TP751
TP302
UPPER
LOWER TP302
TP301
WF7
AUDIO (L) 1V 0.5ms
WF8
WF9
SPDIF 1V 0.1µs
Pin 12 of CN1601
Pin 14 of CN1601
Pin 16 of CN1601
AUDIO (R) 1V 0.5ms
V-OUT E-E 0.2V 20µs
V-OUT 0.5V50µsRF-SW 5V
C-PB RF-SW 5V 5ms
0.2V
NOTE:Input COLOR BAR SIGNAL (WITH 1KHz AUDIO SIGNAL)
WF4
WF6 Pin 2 of IC751
WF5
Pin 8 of CN1601
Pin 10 of CN1601
VIDEO-Y 0.2V 20µs
VIDEO-C 0.2V 20µs
VIDEO-CVBS 0.5V 20µs
1-14-1 DL8NWF
WIRING DIAGRAM < VCR SECTION >
AC
E H
EA
D A
SS
EM
BL
Y
AU
DIO
HE
AD
AU
DIO
E
RA
SE
HE
AD
CO
NT
RO
L H
EA
D
MLO
AD
ING
MO
TO
R
CY
LIN
DE
R A
SS
EM
BL
Y
AE
-H1
AE
-H/F
E-H
2A
-CO
M3
AU
DIO
-PB
/RE
C4
CT
L(+
)5
CT
L(-)
6
VID
EO
-CO
M5
VID
EO
(R)-
26
VID
EO
(R)-
11
VID
EO
-CO
M2
VID
EO
(L)-
23
VID
EO
(L)-
14
P-O
N+
5V1
AL+
12V
(1)
2
C-F
/R3
C-F
G4
C-C
ON
T5
GN
D6
LM-F
WD
/RE
V7
D-C
ON
T8
D-P
FG
9G
ND
10A
L+12
V11
AL+
18V
12
FE
-H1
FE
-H-G
ND
2
CN
501
CN
502
CN
504
CN
253
CN
2003
W01
1C
N20
02
EV
+1.
2VE
V+
1.2V
EV
+3.
3VE
V+
3.3V
EV
+3.
3VD
VD
-P-O
N+
3.3V
DV
D-P
-ON
+5V
EV
+11
VE
V+
11V
GN
D
1 2 3 4 5 6 7 8 9 10
CN
1001
GN
DG
ND
GN
DG
ND
GN
DG
ND
PW
RC
ON
SK
IP-U
PS
KIP
-DO
WN
PLA
Y
11 12 13 14 15 16 17 18 19 20
GN
DV
OD
EO
-Pr/
Cr
GN
DV
IDE
O-P
b/C
b
VID
EO
-Y(I
/P)
GN
DV
IDE
O-C
GN
D
4 5 6
I/P-S
W NU
2 3 7 8 9 10 11
CN
1601
DV
D-A
UD
IO-M
UT
ED
VD
-AU
DIO
(L)
DV
D-A
UD
IO(R
)
12 13 14
RE
MO
TE
DIS
CIN
-L21 22
DV
D-P
OW
ER
23
DV
D-P
LAY
DV
D-O
PE
N/C
LOS
E24 25
DV
D-S
TO
P26
CA
PS
TA
N M
OT
OR
FU
LLE
RA
SE
HE
AD
FE
HE
AD
VID
EO
(R)1
HE
AD
VID
EO
(L)1
HE
AD
VID
EO
-IN
2A
UD
IO(R
)-I
N2 FR
ON
T
VID
EO
(L)2
HE
AD
VID
EO
(R)2
HE
AD
MA
IN C
BA
(DE
CK
AS
SE
MB
LY
)
SE
NS
OR
CB
A
DV
D O
PE
N/C
LO
SE
CB
A
PO
WE
R S
W C
BA
SE
NS
OR
CB
A
TO
WIR
ING
D
IAG
RA
M
<D
VD
SE
CT
ION
>
TO
DV
DM
AIN
CB
AU
NIT
CN
401
(W
002)
TO
DV
DM
AIN
CB
AU
NIT
CN
601
(W00
4)
VID
EO
-OU
TV
IDE
O-I
N1
AU
DIO
(R)
-OU
T2
AU
DIO
(L)
-OU
T2
VID
EO
-Y O
UT
VID
EO
-Pr/
Cr
OU
T
VID
EO
-Pb/
Cb
OU
T
AU
DIO
(R)
-OU
T1
S-V
IDE
OO
UT
AU
DIO
(L)
-OU
T1
RE
AR
DIG
ITA
LA
UD
IO O
UT
(CO
AX
IAL)
EV
+3.
3V1
1DV
D-O
PEN/
CLO
SE2
2AC
CO
RD
MD
RU
MM
OT
OR
PG
SE
NS
OR
M
CA
PS
TA
NM
OT
OR
MO
TO
RD
RIV
EC
IRC
UIT
GN
D15
SP
DIF
16
CN
509
CN
508
W01
3P
OW
ER
-LE
D1
1P
OW
ER
-LE
D2
2K
EY
-13
3G
ND
44
AU
DIO
(L)
-IN
2 A
UD
IO(R
)-I
N1
AU
DIO
(L)
-IN
1
Hi-F
i AU
DIO
(R)
HE
AD
Hi-F
i AU
DIO
(L)
HE
AD
Hi-F
i-AU
DIO
(R)
7H
i-Fi-C
OM
8H
i-Fi-A
UD
IO(L
)9
E8E6EWI1-15-1
WIRING DIAGRAM < DVD SECTION >
DV
D M
EC
HA
NIS
M
DV
D M
AIN
CB
A U
NIT
TO
WIR
ING
D
IAG
RA
M
<V
CR
SE
CT
ION
>
TO
MA
IN C
BA
CN
1001
(W00
2)
TO
MA
IN C
BA
CN
1601
(W00
4)
CN
301
1S
P(+
)2
SP
(-)
3G
ND
4S
L(-)
5S
L(+
)6
TR
AY-I
N
TR
AY
-IN D
RIV
E C
BA
MS
LED
MO
TO
R
MS
PIN
DLE
MO
TO
R
EV
+1.
2VE
V+
1.2V
EV
+3.
3VE
V+
3.3V
EV
+3.
3VD
VD
-P-O
N+
3.3V
DV
D-P
-ON
+5V
EV
+11
VE
V+
11V
GN
D
4 5 6 7 8 9 10 11 12 13
GN
DG
ND
GN
DG
ND
GN
DG
ND
PW
RC
ON
14 15 16 17 18 19 20 21 22 23
RE
MO
TE
24 25
DV
D-P
OW
ER
26
DV
D-P
LAY
DV
D-O
PE
N/C
LOS
E27 28
DV
D-S
TO
P29
CN
401
PIC
K U
P U
NIT
CN
201
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
TS
(+)
TS
(-)
FS
(-)
CD
-LD
FS
(+)
GN
D(D
VD
-PD
)G
ND
(CD
-PD
)
PD
-MO
NI
DV
D-L
D
VR
EF
NU
GN
D
B DV
D-P
-ON
+5V
CD
/DV
DDACN
U
GN
D(L
D)
DE
TEC
TOR
FS
TS
7 9 11 2 3 6 5 4
GN
DV
OD
EO
-Pr/
Cr
GN
DV
IDE
O-P
b/C
b
VID
EO
-Y(I
/P)
GN
DV
IDE
O-C
GN
D
4 5 6
I/P-S
W N
U2 3 7 8 9 10 11
CN
601
GN
D15
DV
D-A
UD
IO-M
UT
ED
VD
-AU
DIO
(L)
DV
D-A
UD
IO(R
)
SP
DIF
12 13 14 16
SK
IP-U
PS
KIP
-DO
WN
PLA
YD
ISC
IN-L
E8E6EWID1-15-2
1-16-1 DL8N4HTI
SYSTEM CONTROL TIMING CHARTS
< VCR Section >
Mode SW: LD-SW
Note: EJ RS: Loading FWD (LM-FWD / REV “H”)RS EJ: Loading REV (LM-FWD / REV “L”)Stop (A) = LoadingStop (B) = Unloading
Note:
LD-SW Position detection A/D Input voltage Limit
(Calculated voltage)Symbol
3.76 V ~ 4.50 V (4.12 V) EJ
4.51 V ~ 5.00 V (5.00 V) CL
0.00 V ~ 0.25 V (0.00 V) SB
1.06 V ~ 1.50 V (1.21 V) TL
0.66 V ~ 1.05 V (0.91 V) FB
1.99 V ~ 2.60 V (2.17 V) SF
1.51 V ~ 1.98 V (1.80 V) SM
3.20 V ~ 3.75 V (3.40 V) AU
0.26 V ~ 0.65 V (0.44 V) AL
4.51 V ~ 5.00 V (5.00 V) SS
2.61 V ~ 3.19 V (2.97 V) RS
Note:
Symbol Loading Status
EJ Eject
CL Eject ~ REW Reel
SB REW Reel ~ Stop (B)
TL Stop (B) ~ Brake Cancel
FB Brake Cancel ~ FF / REW
SF FF / REW ~ Stop (M), (FF / REW)
SM Stop (M), (FF / REW) ~ Stop (A)
AU Stop (A) ~ Play / REC
AL Play / REC ~ Still / Slow
SS Still / Slow ~ RS (REW Search)
RS RS (REW Search)
1-16-2 DL8N4HTI
Still/Slow Control Frame Advance Timing Chart
1) SP Mode
Fig. 1
18 RF-SW
F-AD(Internal Signal)
C-DRIVE
PB CTL
27 C-F/R
79 H-A-SW
78 C-ROTA
The first rise of RF-SW after a rise in F-AD signal
Acceleration Detection (T1)
AT"H"
"Z""H"
"L" "L"
Stop detection (T2)
ST Slow Tracking Value
BL Reversal Limit Value
STILL FRAME ADVANCE STILL
20ms
1-16-3 DL8N4HTI
2) LP/SLP Mode
Fig. 2
18 RF-SW
F-AD(Internal Signal)
C-DRIVE
PB CTL
27 C-F/R
79 H-A-SW
78 C-ROTA
"H""Z"
"H"
"L" "L"
STILL STILL
AT
ST
BL
Stop detection (T2)
Acceleration Detection (T1) Slow Tracking Value
Reversal Limit Value
FRAME ADVANCE
The first rise of RF-SW after a rise in F-AD signal
20ms
1-16-4 DL8N4HTI
Fig. 3
1. EJE
CT
(PO
WE
R O
FF
) -> CA
SS
ET
TE
IN (P
OW
ER
ON
) -> STO
P(B
) -> STO
P(A
) -> PL
AY
-> RS
-> FS
-> PL
AY
-> ST
ILL
-> PL
AY
-> STO
P(A
)
EJECT
CASS.LOAD
ST-S/END-S "OFF"
PLAY
REW
FF
PLAY
PLAY
STOP/EJECT
0.2S
0.7S
0.4S
0.2S
LD-FWD
STOP(A)
STOP(A)
LD-FWD
LD-REV
0.2S
LD-FWD
LD-FWD
LD-FWD
LD-FWD
LD-FWD
STILL(SLOW)
RS
FS
PLAY
PLAY
PLAY
0.2S
LD-REV
LD-REV
LD-FWD
LD-FWD
LD-REV
LD-REV
LD-REV
0.2S
0.5S
PIN
NO
.
CLEJ
SSSS
AUAU
TLL
D-S
W
CL
/SS
LM
-FW
D "M
"
/RE
V
C-D
RIV
E "Z"
ON
ON
C-F
/R
DR
UM
RO
TAT
ION
P-O
N-L
AU
DIO
-M
UT
E-H
D-R
EC
-H
D-P
B
PAUSE(SLOW)
AUAL
ALAU
SFSM
EJ
AU
RS
SF
SM
TL
FB
AL
SB
68
212722724
PO
WE
R-O
FF
STO
PP
LA
YR
SF
SS
TIL
L(S
LO
W)
PL
AY
STO
PP
LA
YD
ISP
LA
Y
SBTL
SBFB
SMSM
SFAL
ALRS
AUAL
SSAU
ALSM
0.8S0.2S
0.3S
1.0S0.2S
1.5S (2H)2.5S (4H)
0.5S
0.2S
0.8S (2H)1.2S (4H)
0.2S
1.2S0.2S
20mS
0.4S
40mS
0.2S
0.2S
Refer to STILL/SLO
W TIM
ING
CHART Fig. 1, 2.
0.3S
0.2S
20mS
40mS
0.4S
0.2S
0.2S0.2S
0.3S
1-16-5 DL8N4HTI
Fig. 4
PIN
NO
.
LD
-SW
CL
/SS
LM
-FW
D "M
"
/RE
V
C-D
RIV
E "Z"
ON
ON
C-F
/R
DR
UM
RO
TAT
ION
P-O
N-L
AU
DIO
-M
UT
E-H
D-R
EC
-H
D-P
B
EJ
AU
RS
SF
SM
TL
FB
AL
SB
68
212722724
VC
R/T
V10
DIS
PL
AY
ST-S/END-S "ON"
REC
REW
FF
STOP/EJECT
0.5S
1.0S
0.2S
0.5S
0.2S
0.5S
0.5S
0.5S
0.2S
0.2S
0.2S
1.5S
2.5S Short REV
1.0S
0.2S
LD-FWD
REV
LD-FWD
STOP(A)
STOP(A)
STOP(A)
CASS. UNLD
EJECT
STOP(A)
LD-REV
FF
LD-REV
LD-REV
LD-FWD
LD-FWD
LD-FWD
LD-FWD
LD-FWD
LD-FWD
LD-FWD
REC PAUSE
REC
REC
REW
LD-REV
LD-REV
LD-REV
LD-REV
LD-REV
LD-REV
LD-REV
PAUSE
REC or PAUSE
STOP/EJECT
STOP/EJECT
STOP/EJECT
2. STO
P(A
) -> FF
-> STO
P(A
) -> RE
W -> S
TOP
(A) -> R
EC
-> PAU
SE
-> PAU
SE
or R
EC
-> STO
P(A
) -> EJE
CT
STO
PF
F
STOP
RE
WS
TOP
RE
CR
EC
RE
C PA
US
ES
TOP
TLTL
SMSM
SFSF
ALAL
SMAL
ALAL
AUAU
SMTL
SBEJ
RSRS
SMSM
SFFB
SMAU
AUSS
SSSS
SFAU
ALAL
AUSS
FBCL
SFFB
SMFB
SFAU
AUFB
SF
1.0S1.2S
0.2S0.2S
40mS
0.4S
0.2S0.2S
0.4S20m
S
40mS
0.2S
20mS
0.2S
0.4S
40mS
20mS
0.1S
Fig. 4
PIN
NO
.
LD
-SW
CL
/SS
LM
-FW
D "M
"
/RE
V
C-D
RIV
E "Z"
ON
ON
C-F
/R
DR
UM
RO
TAT
ION
P-O
N-L
AU
DIO
-M
UT
E-H
D-R
EC
-H
D-P
B
EJ
AU
RS
SF
SM
TL
FB
AL
SB
68
212722724
DIS
PL
AY
ST-S/END-S "ON"
REC
REW
FF
STOP/EJECT
0.5S
1.0S
0.2S
0.5S
0.2S
0.5S
0.5S
0.5S
0.2S
0.2S
0.2S
1.5S
2.5S Short REV
1.0S
0.2S
LD-FWD
REV
LD-FWD
STOP(A)
STOP(A)
STOP(A)
CASS. UNLD
EJECT
STOP(A)
LD-REV
FF
LD-REV
LD-REV
LD-FWD
LD-FWD
LD-FWD
LD-FWD
LD-FWD
LD-FWD
LD-FWD
REC PAUSE
REC
REC
REW
LD-REV
LD-REV
LD-REV
LD-REV
LD-REV
LD-REV
LD-REV
PAUSE
REC or PAUSE
STOP/EJECT
STOP/EJECT
STOP/EJECT
2. STO
P(A
) -> FF
-> STO
P(A
) -> RE
W -> S
TOP
(A) -> R
EC
-> PAU
SE
-> PAU
SE
or R
EC
-> STO
P(A
) -> EJE
CT
STO
PF
F
STOP
RE
WS
TOP
RE
CR
EC
RE
C PA
US
EE
JEC
T
TLTL
SMSM
SFSF
ALAL
SMAL
ALAL
AUAU
SMTL
SBEJ
RSRS
SMSM
SFFB
SMAU
AUSS
SSSS
SFAU
ALAL
AUSS
FBCL
SFFB
SMFB
SFAU
AUFB
SF
1.0S1.2S
0.2S0.2S
40mS
0.4S
0.2S0.2S
0.4S20m
S
40mS
0.2S
20mS
0.2S
0.4S
40mS
20mS
0.1S
1-16-6 DL8N4HTI
< DVD Section >
Tray IN(TL221)
Sled Drive(TP303)
Disc Drive(TP301)
Focus Drive(TP304)
Tracking Drive(TP302)
0V
3.3V
0V
1.65V
0V
0V
0V
1.65V
1.65V
1.65V
Tray Close ~ Play / Play ~ Tray Open
TrayClose
Disc Rotation
PlayDisc Stop
Tray Open
1-17-1 E8E6DPIN
IC PIN FUNCTION DESCRIPTIONS
< VCR Section >
IC501 (SERVO/SYSTEM CONTROL/OSD)
“H” ≥ 4.5 V, “L” ≤ 1.0 V
Pin No.
IN/OUT
Signal Name Function
1 IN P-DOWN -H
Power Voltage Down Detector Signal
2 IN REC-SAF-SW
Recording Safety SW Detect (With Record tab = “L” / With out Record tab = “H”)
3 IN T-REEL Take Up Reel Rotation Signal
4 OUTDVD-REMOTE-INH
DVD Remote Inhibition signal
5 IN REMOTE-VIDEO Remote Control Sensor
6 - NU Not Used
7 OUT AUDIO-MUTE-H
Audio Mute Control Signal (Mute = “H”)
8 - NU Not Used
9 - NU Not Used
10 OUT POWER-LED POWER LED Signal Output
11 OUT POWER-LED POWER LED Signal Output
12IN/
OUTIIC-BUS SDA IIC BUS Control Data
13 OUT IIC-BUS SCL IIC BUS Control Clock
14 OUT YCA-SCL YCA IC Control Clock
15 OUT YCA-SDA YCA IC Control Data
16 OUT YCA-CS YCA IC Control Chip Select
17 OUT P-ON-CONT
Power Regulator Control Signal
18 OUT RF-SW Video Head Switching Pulse
19 OUT D-V SYNC Dummy V-sync Output
20 IN RESET System Reset Signal (Reset = “L”)
21 OUT LM-FWD/ REV
Loading Motor FWD/ REV Output
22 OUT P-ON-L Power On Signal to Low
23 - NU Not Used
24 OUT D-REC-H Delayed Record Signal
25 OUT Hi-Fi-H-SW
HiFi Audio Head Switching Pulse
26 OUT DVD-POWER DVD Power Control Signal
27 OUT C-F/RCapstan Motor FWD/REV Control Signal (FWD = “L” / REV = “H”)
28 OUT C-CONT Capstan Motor Control Signal
29 OUT D-CONT Drum Motor Control Signal
30 - NU Not Used
31 - VDD VDD
32 OUT OSCO Main Clock Output 14.31818MHz
33 IN OSCI Main Clock Input 14.31818MHz
34 - VSS VSS
35 IN XI Sub Clock Input 32.768 MHz
36 OUT XO Sub Clock Output 32.768 MHz
37 IN SXI Operation Mode Selecting Input Signal
38 OUT VIDEO-OUT
Composite Video Signal Output
39 - VSS2 Vss2
40 IN VIDEO-IN Composite Video Signal Input
41 IN C-SYNC Composite Synchronized Pulse
42 - VDD2 VDD2
43 IN AFCC Low Path Filter Input Signal For AFC
44 OUT AFCLPF Low Path Filter Output Signal For AFC
45 - NU Not Used
46 OUT OUTPUT- SELECT(1)
Output Select
47 IN D-PFG Drum PG/FG Input Signal
48 IN POWER-SAFETY
P-ON Power Supply Abnormal Detection Input
49 IN C-FG Capstan Motor Rotation Detection Pulse
50 - AFG GND
51 OUT VRO Servo Standard Voltage Output
52 IN VRI Servo Standard Voltage Input
53 - AVSS AVSS
54 IN CTLA CTL Amp. AC GND
55 - AVDD AVDD
Pin No.
IN/OUT
Signal Name Function
1-17-2 E8E6DPIN
56 IN/OUT CTL (+) Playback/Record Control
Signal (+)
57 IN/OUT CTL (-) Playback/Record Control
Signal (-)
58 OUT CTL Amp. Output Control Signal for Test Point
59 IN Hi-Fi/NOR-IN
Audio Mode Input (HiFi = “L” / Normal = “H”)
60 INDVD-POW-MONITOR
DVD Power Monitor Signal (P-off = “L”, P-on = “H”)
61 - NU Not Used
62 IN END-S Tape End Position Detect Signal
63 OUT SENSOR-SW Sensor LED Control Signal
64 IN V-ENV Video Envelope Comparator Signal
65 IN PG-DELAY
Video Head Switching Pulse Signal Adjusted Voltage
66 IN KEY-2 A/D Key Data Signal 2
67 IN KEY-1 A/D Key Data Signal 1
68 IN LD-SW Deck Mode Position Detector Signal
69 IN ST-S Tape Start Position Detector Signal
70 OUT VCR-LED-L VCR Mode LED Signal Output
71 OUT VCR-LED-L VCR Mode LED Signal Output
72 OUT DVD-LED-L DVD Mode LED Signal Output
73 OUT DVD-LED-L DVD Mode LED Signal Output
74 OUT REC-LED-L REC Mode LED Signal Output
75 OUT REC-LED-L REC Mode LED Signal Output
76 OUT TIMER-LED-L
TIMER Mode LED Signal Output
77 OUT TIMER-LED-L
TIMER Mode LED Signal Output
78 OUT C-ROTA Color Phase Rotary Changeover Signal
79 OUT H-A-SW Video Head Amp Switching Pulse
80 IN H-A-COMP Head Amp Comparator Signal
Pin No.
IN/OUT
Signal Name Function
1-18-1 E8E6DLE
LEAD IDENTIFICATIONS
60
21
40
41
201
80
61
1
2
4
3
EC
B1 E B2
C1 C2
4 5
3 12
E C B E C B
1 4
8 5
16 9
81
1 4
8 5
C
B E
E C B
24 13
1 12
48
17
32
33
161
64
49
UTC0532
1: VREF2: GND3: VC4: VIN5: VOUT
LA71208EB-3EMN101D08DZLAN3663FBP-TV
Note:A: AnodeK: CathodeE: EmitterC: CollectorB: BaseR: ReferenceS: SourceG: GateD: Drain
2SC3199(G,L) 2SA1266G2SC3203Y2SC5343G-ATRA103S
MMBTSA1504GMMBTRC101SSMMBTRC103SSMMBTSC3265YMMBTSC3875LMMBTSC3875YMMBTSC3879YRC103S
EL817B
PT204-6B-12 TK5A50D AN13410ARN1511(TE85R.F)
MM1637XVBE4053L-S16-R
1: Anode2: Cathode3: Emitter4: Collector
UTC4558TE FA5640N-C6-TE3
1-19-1 E8E6ECEX
EXPLODED VIEWS
Cabinet
2B9
2B2
2L051
2L051
2L051
2B3
2L011
2L012
1B1
2L071
2L071
2L0712L071
A2
2L041
2L041
2L041
2L041
2B40
2L022
2L022
2L0212L021
2L021
1B2
L0-9
L0-9
DVD Main CBA Unit
Sensor CBA
Sensor CBA
AC1001
2B11
2B152B15RM2001
DVD Open/Close CBA
W002
W011
2L091
2L054
A10
2L012
B
Main CBA
A5
2L0212L062
A
B
A
F1002
W004
A14
A15
2B16
A3
See Electrical Parts Listfor parts with this mark.
Some Ref. Numbers are not in sequence.
2B152B15
These FFC cables are included in 1B2 (DVD mechanism).
A1X
2B2
Main CBA
2L054
W013
Power SW CBA
2B13C
C
2B2
2L051
2L051 2L054
2B132B16
1-19-2 E8E6EPEX
Packing
S2
S2
S2
S1
Unit
A14
FRONT
S3
X1
X4
X20X22 X5 X2
Upper SideLower Side
20131216 1-20-1 E8E6ECA
MECHANICAL PARTS LIST
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTE: Parts that are not assigned part numbers (---------) are not available.
Ref.No. Description Parts No.
A1X FRONT ASSEMBLY E8E6EUH 2VMA00063
A2 TOP CASE E8C1TCD 1VM323281
A3 CHASSIS ASSEMBLY E8K6BCD 1VM337123A
A10# MODEL NO. LABEL E8E6EUH ----------
A14 BARCODE LABEL E8E6EUH ----------
A15 CAUTION LABEL E8E6EUH ----------
1B1 DECK ASSEMBLY CZD014/VM2460 N2460FL
1B2 DVD MECHA E7 N79FGKVM N79FGKVM
2B2 TOP BRACKET H9600UD 0VM204470
2B3 RODER HOLDER H9600UD 0VM306676
2B16 TAPE HIMELON H9206JD 0VM413956
2B40 PARTITION PLATE E8A00UD 1VM321985
2L011 SCREW BIND 3CHROM +P-TITE M3X8.0 M3X8 BIND HEAD+
GBJP3080
2L012 SCREW C-TIGHT M3X6 E5610UD 0VM412937A
2L021 SCREW BIND 3CHROM +P-TITE M3X12.0 M3*12 BIND+
GBJP3120
2L022 SCREW BIND 3CHROM +P-TITE M3X8.0 M3X8 BIND HEAD+
GBJP3080
2L041 SCREW BIND BLACK_NI +P-TITE M3X10.0 3X10 BIND HEAD+
GBHP3100
2L051 SCREW BIND 3CHROM +P-TITE M3X6.0 M3X6 BIND HEAD+
GBJP3060
2L054 SCREW BIND 3CHROM +P-TITE M3X6.0 M3X6 BIND HEAD+
GBJP3060
2L071 SCREW F-PAN 3CHROM +P-TITE M3X10.0 M3*10 WASHERHEAD+
GCJP3100
2L091 SCREW BIND TIN +P-TITE M3X8.0 M3X8 BIND HEAD+
GBCP3080
L0-9 SCREW BIND 3CHROM +P-TITE M3X8.0 M3X8 BIND HEAD+
GBJP3080
PACKINGS1 GIFT BOX CARTON E8E6EUH 2VMC00256
S2 STYROFOAM H9600UD 0VM204474E
S3 SET BAG E8P6BUH 2VMC00096
ACCESSORIESX1 REMOTE CONTROL UNIT NC203UH NC203UH
X2 BATTERY DRY R03(SIZE AAA ) XB00M0RKT001
X4 ACCESSORY BAG E5700UD 0VM415576C
X5 AV CORD 1000/BLACK WPZ0102TM018
X20# OWNERS MANUAL E8E6EUH 2VMN00109
X22 QUICK START GUIDE E8E6EUH 2VMN00110
20131216 1-21-1 E8E6EEL
ELECTRICAL PARTS LIST
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------) are not available.
2. Tolerance of Capacitors and Resistors are noted with the following symbols.
DVD MAIN CBA UNIT
MCV CBA
MAIN CBA
C.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
Ref. No. Description Parts No.
DVD MAIN CBA UNIT N6APBKUP
Ref. No. Description Parts No.
MCV CBAConsists of the following
2VSA00840
MAIN CBA (MCV-A)POWER SW CBA (MCV-B)DVD OPEN/CLOSE CBA (MCV-C)SENSOR CBA
------------------------------1VSA13493
Ref. No. Description Parts No.
MAIN CBA (MCV-A)Consists of the following:
----------
CAPACITORSC013 ELECTROLYTIC CAP. 22F/50V M(105C) CE1JMASTH220
C018 ELECTROLYTIC CAP. 1000F/16V M(105C) CE1CMASTH102
C020 ELECTROLYTIC CAP. 2200F/10V M(105C) CE1AMASTH222
C021 ELECTROLYTIC CAP. 470F/6.3V M CE0KMASDL471
C023 ELECTROLYTIC CAP. 100F/16V M CE1CMASDL101
C041 CAP CERAMIC (AX) 0.068F/50V/B/K CA1J683TU061
C051 ELECTROLYTIC CAP. 10F/16V M H7 CE1CMAVSL100
C053 ELECTROLYTIC CAP. 470F/6.3V M CE0KMASDL471
C301 ELECTROLYTIC CAP. 1F/50V M H7 CE1JMAVSL1R0
C302 CHIP CERAMIC CAP.(1608) CH J 390pF/50V CHD1JJ3CH391
C304 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C305 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C307 CHIP CERAMIC CAP. F Z 1F/10V CHD1AZ30F105
C308 ELECTROLYTIC CAP. 47F/6.3V M H7 CE0KMAVSL470
C309 CHIP CERAMIC CAP.(1608) F Z 0.1F/50V CHD1JZ30F104
C310 ELECTROLYTIC CAP. 22F/6.3V M H7 CE0KMAVSL220
C311 ELECTROLYTIC CAP. 1F/50V M H7 CE1JMASSL1R0
C312 CHIP CERAMIC CAP. F Z 1F/10V CHD1AZ30F105
C313 ELECTROLYTIC CAP. 1F/50V M H7 CE1JMASSL1R0
C314 CHIP CERAMIC CAP. F Z 1F/10V CHD1AZ30F105
C315 CHIP CERAMIC CAP.(1608) B K 0.1F/25V CHD1EK30B104
C316 CHIP CERAMIC CAP. F Z 1F/10V CHD1AZ30F105
C317 CHIP CERAMIC CAP. F Z 1F/10V CHD1AZ30F105
C319 CHIP CERAMIC CAP.(1608) CH J 10pF/50V CHD1JJ3CH100
C321 CHIP CERAMIC CAP.(1608) B K 0.01F/50V CHD1JK30B103
C322 CHIP CERAMIC CAP.(1608) CH J 68pF/50V CHD1JJ3CH680
C327 ELECTROLYTIC CAP. 47F/6.3V M H7 CE0KMAVSL470
C328 ELECTROLYTIC CAP. 1F/50V M H7 CE1JMAVSL1R0
C329 CHIP CERAMIC CAP.(1608) B K 0.01F/50V CHD1JK30B103
C330 ELECTROLYTIC CAP. 1F/50V M H7 CE1JMAVSL1R0
C331 CHIP CERAMIC CAP.(1608) B K 0.01F/50V CHD1JK30B103
C332 ELECTROLYTIC CAP. 1F/50V M H7 CE1JMAVSL1R0
C333 CHIP CERAMIC CAP.(1608) F Z 0.1F/50V CHD1JZ30F104
C336 CHIP CERAMIC CAP.(1608) B K 0.01F/50V CHD1JK30B103
C339 CHIP CERAMIC CAP.(1608) B K 0.047F/50V CHD1JK30B473
C340 CHIP CERAMIC CAP.(1608) B K 0.1F/25V CHD1EK30B104
C341 CHIP CERAMIC CAP.(1608) B K 0.047F/50V CHD1JK30B473
C342 CHIP CERAMIC CAP.(1608) F Z 0.1F/50V CHD1JZ30F104
C343 ELECTROLYTIC CAP. 47F/6.3V M H7 CE0KMAVSL470
C348 CHIP CERAMIC CAP.(1608) B K 0.1F/25V CHD1EK30B104
C352 CHIP CERAMIC CAP. B K 10F/10V CHE1AK30B106
C391 ELECTROLYTIC CAP. 100F/16V M CE1CMASDL101
C392 ELECTROLYTIC CAP. 470F/6.3V M CE0KMASDL471
C401 CHIP CERAMIC CAP.(1608) F Z 0.1F/50V CHD1JZ30F104
C404 CHIP CERAMIC CAP.(1608) B K 0.01F/50V CHD1JK30B103
C405 ELECTROLYTIC CAP. 22F/6.3V M H7 CE0KMAVSL220
C406 ELECTROLYTIC CAP. 33F/6.3V M H7 CE0KMAVSL330
C407 CHIP CERAMIC CAP.(1608) B K 0.01F/50V CHD1JK30B103
C408 CHIP CERAMIC CAP.(1608) B K 0.012F/50V CHD1JK30B123
C409 ELECTROLYTIC CAP. 10F/16V M H7 CE1CMAVSL100
C410 CHIP CERAMIC CAP.(1608) B K 2700pF/50V CHD1JK30B272
C411 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C412 ELECTROLYTIC CAP. 4.7F/25V M H7 CE1EMAVSL4R7
C413 CHIP CERAMIC CAP.(1608) B K 6800pF/50V CHD1JK30B682
C414 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C422 ELECTROLYTIC CAP. 47F/6.3V M H7 CE0KMAVSL470
C423 ELECTROLYTIC CAP. 220F/6.3V M H7 CE0KMAVSL221
C424 CERAMIC CAP. B K 470pF/100V CCD2AKP0B471
C425 CAP POLYESTER FILM 0.018F/100V J CA2A183SER02
C430 CHIP CERAMIC CAP. CH J 56pF/50V CHD1JJ3CH560
C440 ELECTROLYTIC CAP. 0.1F/50V M H7 CE1JMAVSLR10
C441 ELECTROLYTIC CAP. 0.1F/50V M H7 CE1JMAVSLR10
C443 CHIP CERAMIC CAP.(1608) B K 0.015F/50V CHD1JK30B153
C448 ELECTROLYTIC CAP. 10F/16V M H7 CE1CMAVSL100
C449 ELECTROLYTIC CAP. 10F/16V M H7 CE1CMAVSL100
C450 CHIP CERAMIC CAP.(1608) B K 0.1F/25V CHD1EK30B104
C451 ELECTROLYTIC CAP. 10F/16V M H7 CE1CMAVSL100
C452 ELECTROLYTIC CAP. 1F/50V M H7 CE1JMAVSL1R0
C453 ELECTROLYTIC CAP. 10F/16V M H7 CE1CMAVSL100
C454 ELECTROLYTIC CAP. 10F/16V M H7 CE1CMAVSL100
C455 ELECTROLYTIC CAP. 33F/6.3V M H7 CE0KMAVSL330
C456 ELECTROLYTIC CAP. 10F/16V M H7 CE1CMAVSL100
C457 ELECTROLYTIC CAP. 22F/6.3V M H7 CE0KMAVSL220
C459 CHIP CERAMIC CAP.(1608) B K 0.015F/50V CHD1JK30B153
C460 CHIP CERAMIC CAP.(1608) B K 0.033F/50V CHD1JK30B333
C461 CHIP CERAMIC CAP.(1608) B K 0.01F/50V CHD1JK30B103
C462 CHIP CERAMIC CAP.(1608) B K 0.01F/50V CHD1JK30B103
C463 CHIP CERAMIC CAP.(1608) B K 0.1F/25V CHD1EK30B104
C464 ELECTROLYTIC CAP. 0.22F/50V M H7 CE1JMAVSLR22
C465 CHIP CERAMIC CAP.(1608) B K 0.01F/50V CHD1JK30B103
C466 ELECTROLYTIC CAP. 47F/16V M H7 CE1CMAVSL470
Ref. No. Description Parts No.
20131216 1-21-2 E8E6EEL
C467 CHIP CERAMIC CAP.(1608) B K 0.022F/50V CHD1JK30B223
C470 CHIP CERAMIC CAP.(1608) B K 0.1F/25V CHD1EK30B104
C471 ELECTROLYTIC CAP. 22F/6.3V M H7 CE0KMAVSL220
C472 ELECTROLYTIC CAP. 10F/16V M H7 CE1CMAVSL100
C473 ELECTROLYTIC CAP. 33F/6.3V M H7 CE0KMAVSL330
C474 ELECTROLYTIC CAP. 10F/16V M H7 CE1CMAVSL100
C480 ELECTROLYTIC CAP. 22F/6.3V M H7 CE0KMAVSL220
C481 ELECTROLYTIC CAP. 10F/16V M H7 CE1CMAVSL100
C483 ELECTROLYTIC CAP. 3.3F/50V M H7 CE1JMAVSL3R3
C490 ELECTROLYTIC CAP. 2.2F/50V M H7 CE1JMAVSL2R2
C491 CHIP CERAMIC CAP.(1608) B K 0.022F/50V CHD1JK30B223
C493 ELECTROLYTIC CAP. 10F/16V M H7 CE1CMAVSL100
C494 ELECTROLYTIC CAP. 1F/50V M H7 CE1JMAVSL1R0
C496 CHIP CERAMIC CAP.(1608) B K 0.01F/50V CHD1JK30B103
C498 ELECTROLYTIC CAP. 47F/16V M H7 CE1CMAVSL470
C502 ELECTROLYTIC CAP. 220F/6.3V M H7 CE0KMAVSL221
C505 ELECTROLYTIC CAP. 22F/10V M H7 CE1AMAVSL220
C507 ELECTROLYTIC CAP. 1F/50V M H7 CE1JMAVSL1R0
C508 CHIP CERAMIC CAP.(1608) B K 0.033F/50V CHD1JK30B333
C509 ELECTROLYTIC CAP. 220F/6.3V M H7 CE0KMAVSL221
C511 CHIP CERAMIC CAP. CH J 15pF/50V CHD1JJ3CH150
C512 CHIP CERAMIC CAP. CH J 18pF/50V CHD1JJ3CH180
C514 CHIP CERAMIC CAP.(1608) CH J 22pF/50V CHD1JJ3CH220
C515 CHIP CERAMIC CAP. CH J 18pF/50V CHD1JJ3CH180
C521 ELECTROLYTIC CAP. 47F/25V M H7 CE1EMAVSL470
C522 CHIP CERAMIC CAP.(1608) B K 4700pF/50V CHD1JK30B472
C523 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C525 CHIP CERAMIC CAP.(1608) B K 4700pF/50V CHD1JK30B472
C527 CHIP CERAMIC CAP.(1608) B K 0.047F/50V CHD1JK30B473
C528 CHIP CERAMIC CAP. B K 470pF/50V CHD1JK30B471
C529 CHIP CERAMIC CAP.(1608) B K 0.022F/50V CHD1JK30B223
C530 ELECTROLYTIC CAP. 1F/50V M H7 CE1JMAVSL1R0
C531 ELECTROLYTIC CAP. 10F/16V M H7 CE1CMAVSL100
C532 ELECTROLYTIC CAP. 10F/16V M H7 CE1CMAVSL100
C533 ELECTROLYTIC CAP. 47F/6.3V M H7 CE0KMAVSL470
C534 CHIP CERAMIC CAP.(1608) B K 0.1F/25V CHD1EK30B104
C535 ELECTROLYTIC CAP. 22F/10V M H7 CE1AMAVSL220
C536 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C537 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C540 CHIP CERAMIC CAP.(1608) B K 0.01F/50V CHD1JK30B103
C541 CHIP CERAMIC CAP.(1608) F Z 0.1F/50V CHD1JZ30F104
C544 ELECTROLYTIC CAP. 100F/6.3V H7 CE0KMAVSL101
C560 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C577 CHIP CERAMIC CAP. F Z 1F/10V CHD1AZ30F105
C751 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C752 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C753 CHIP CERAMIC CAP.(1608) B K 0.01F/50V CHD1JK30B103
C757 ELECTROLYTIC CAP. 47F/6.3V M H7 CE0KMAVSL470
C761 CHIP CERAMIC CAP.(1608) CH J 47pF/50V CHD1JJ3CH470
C766 CHIP CERAMIC CAP.(1608) B K 0.01F/50V CHD1JK30B103
C772 ELECTROLYTIC CAP. 4.7F/50V M H7 CE1JMAVSL4R7
C773 ELECTROLYTIC CAP. 4.7F/50V M H7 CE1JMAVSL4R7
C774 ELECTROLYTIC CAP. 47F/25V M H7 CE1EMAVSL470
C1001# CAP METALLIZED FILM 0.068F/275V/K/MPX CTA683SER002
C1002 ELECTROLYTIC CAP. 47F/50V CE1JMASTH470
C1003 ELECTROLYTIC CAPACIT0R 150F/200V CA2D151S6012
C1004# SAFETY CAP. 3300pF/250V CCG2EMA0F332
C1005 CHIP CERAMIC CAP.(1608) CH J 47pF/50V CHD1JJ3CH470
C1006 CHIP CERAMIC CAP.(1608) B K 0.01F/50V CHD1JK30B103
C1007 ELECTROLYTIC CAP. 1000F/6.3V M CE0KMASDL102
C1008 CHIP CERAMIC CAP. B K 470pF/50V CHD1JK30B471
C1010 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C1011 ELECTROLYTIC CAP. 47F/35V M CE1GMASDL470
Ref. No. Description Parts No.
C1012 CERAMIC CAP LR SERIES 2KV 470PF CCE471WAL004
C1013 CAP METALLIZED FILM 0.01/400/K/MEX CMK103NRN002
C1014 ELECTROLYTIC CAP. 470F/6.3V M CE0KMASDL471
C1015 ELECTROLYTIC CAP. 220F/6.3V M CE0KMASDL221
C1023 CERAMIC CAP. B K 220pF/500V CCD2JKS0B221
C1030 CAP CERAMIC (AX) 0.1F/50V/B/K CA1J104TU061
C1031 CAP CERAMIC (AX) 0.1F/50V/B/K CA1J104TU061
C1039 CAP CERAMIC (AX) 0.1F/50V/B/K CA1J104TU061
C1040 ELECTROLYTIC CAP. 330F/6.3V M CE0KMASDL331
C1042 ELECTROLYTIC CAP. 100F/6.3V M H7 CE0KMASSL101
C1051 CAP CERAMIC (AX) 0.1F/50V/B/K CA1J104TU061
C1052 CHIP CERAMIC CAP. F Z 1F/10V CHD1AZ30F105
C1053 CHIP CERAMIC CAP. F Z 1F/10V CHD1AZ30F105
C1054 CHIP CERAMIC CAP. F Z 1F/10V CHD1AZ30F105
C1070 CHIP CERAMIC CAP. F Z 1F/10V CHD1AZ30F105
C1082 ELECTROLYTIC CAP. 220F/16V M H7 CE1CMASSL221
C1101 CHIP CERAMIC CAP.(1608) B K 0.1F/25V CHD1EK30B104
C1201 ELECTROLYTIC CAP. 10F/16V M H7 CE1CMAVSL100
C1202 ELECTROLYTIC CAP. 10F/16V M H7 CE1CMASSL100
C1207 CHIP CERAMIC CAP.(1608) CH J 68pF/50V CHD1JJ3CH680
C1208 CHIP CERAMIC CAP.(1608) CH J 68pF/50V CHD1JJ3CH680
C1221 ELECTROLYTIC CAP. 10F/16V M H7 CE1CMASSL100
C1222 ELECTROLYTIC CAP. 10F/16V M H7 CE1CMASSL100
C1223 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1224 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1245 CHIP CERAMIC CAP.(1608) F Z 0.1F/50V CHD1JZ30F104
C1246 CHIP CERAMIC CAP.(1608) F Z 0.1F/50V CHD1JZ30F104
C1247 ELECTROLYTIC CAP. 470F/6.3V M CE0KMASDL471
C1249 ELECTROLYTIC CAP. 100F/16V M H7 CE1CMAVSL101
C1351 CHIP CERAMIC CAP.(1608) B K 0.1F/25V CHD1EK30B104
C1352 ELECTROLYTIC CAP. 47F/6.3V M H7 CE0KMAVSL470
C1354 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C1355 RES CHIP 1608 1/10W 0 RRXA000HH014
C1359 CHIP CERAMIC CAP.(1608) CH D 10pF/50V CHD1JD3CH100
C1421 CHIP CERAMIC CAP.(1608) B K 0.01F/50V CHD1JK30B103
C1422 CHIP CERAMIC CAP.(1608) B K 0.1F/25V CHD1EK30B104
C1441 CHIP CERAMIC CAP.(1608) B K 1F/10V CHD1AK30B105
C1442 ELECTROLYTIC CAP. 1000F/6.3V M CE0KMASDL102
C1462 ELECTROLYTIC CAP. 220F/6.3V M CE0KMASDL221
C1465 CHIP CERAMIC CAP.(1608) B K 1F/10V CHD1AK30B105
C1466 CHIP CERAMIC CAP.(1608) B K 1F/10V CHD1AK30B105
C1482 ELECTROLYTIC CAP. 220F/6.3V M CE0KMASDL221
C1523 CHIP CERAMIC CAP.(1608) F Z 0.1F/50V CHD1JZ30F104
C1524 ELECTROLYTIC CAP. 100F/6.3V H7 CE0KMAVSL101
C1531 CHIP CERAMIC CAP.(1608) B K 0.01F/50V CHD1JK30B103
C1532 ELECTROLYTIC CAP. 22F/6.3V M H7 CE0KMAVSL220
C1801 CHIP CERAMIC CAP.(1608) B K 1F/10V CHD1AK30B105
C1802 CHIP CERAMIC CAP.(1608) F Z 0.1F/50V CHD1JZ30F104
C1803 CHIP CERAMIC CAP.(1608) B K 1F/10V CHD1AK30B105
C1804 CHIP CERAMIC CAP.(1608) F Z 0.1F/50V CHD1JZ30F104
C1805 CHIP CERAMIC CAP.(1608) B K 1F/10V CHD1AK30B105
C1806 CHIP CERAMIC CAP.(1608) F Z 0.1F/50V CHD1JZ30F104
C1807 CHIP CERAMIC CAP.(1608) F Z 0.1F/50V CHD1JZ30F104
C1808 CHIP CERAMIC CAP.(1608) B K 0.1F/25V CHD1EK30B104
C1809 CHIP CERAMIC CAP.(1608) B K 1F/10V CHD1AK30B105
C1810 CHIP CERAMIC CAP. CH J 120pF/50V CHD1JJ3CH121
C1811 CHIP CERAMIC CAP. B K 470pF/50V CHD1JK30B471
C1812 CHIP CERAMIC CAP. B K 470pF/50V CHD1JK30B471
C2002 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C2004 ELECTROLYTIC CAP. 100F/6.3V H7 CE0KMAVSL101
C2012 CHIP CERAMIC CAP.(1608) F Z 0.1F/50V CHD1JZ30F104
Ref. No. Description Parts No.
20131216 1-21-3 E8E6EEL
DIODESD013 RECTIFIER DIODE BA158 NDQZ000BA158
D015 SCHOTTKY BARRIER DIODE SB390 NDQZ000SB390
D016 SCHOTTKY BARRIER DIODE SB240-B/P NDQZ000SB240
D019 WIRE CP STP-S-0.60 XZ40F0REN002
D031 ZENER DIODE SMD MM3Z16B ND1B0MM3Z16B
D035 ZENER DIODE SMD MM3Z7V5B ND1BMM3Z7V5B
D041 IC SHUNT REGULATOR AS431BZTR-E1 NSZBA0TBCD01
D052 DIODE ZENER 10BSB-T26 NDTB010BST26
D062 DIODE ZENER 4V3BSC-T26 NDTC4R3BST26
D063 RECTIFIER DIODE 1N4005 NDQZ001N4005
D080 RECTIFIER DIODE 1N4005 NDQZ001N4005
D082 RECTIFIER DIODE 1N4005 NDQZ001N4005
D451 DIODE SWITCHING 1N4148-F0021 NDTZ01N4148F
D504 ZENER DIODE SMD MM3Z18B ND1B0MM3Z18B
D555 LED SIR-563ST3F P QPQPS1R563ST
D564 LED(RED) LTL-4222 NPQZ0LTL4222
D565 LED(RED) LTL-4222 NPQZ0LTL4222
D566 LED(GREEN) LTL-1CHGE NPQZLTL1CHGE
D567 LED(GREEN) LTL-1CHGE NPQZLTL1CHGE
D777 ZENER DIODE SMD MM3Z6V8B ND1BMM3Z6V8B
D1001 RECTIFIER DIODE 1N4005 NDQZ001N4005
D1002 RECTIFIER DIODE 1N4005 NDQZ001N4005
D1003 RECTIFIER DIODE 1N4005 NDQZ001N4005
D1004 RECTIFIER DIODE 1N4005 NDQZ001N4005
D1006 SCHOTTKY BARRIER DIODE SB140 NDQZ000SB140
D1007 CHIP ZENER DIODE CRZ27(TE85L Q QD1Z00CRZ27Q
D1008 SCHOTTKY BARRIER DIODE SB140 NDQZ000SB140
D1009 CHIP ZENER DIODE CRZ27(TE85L Q QD1Z00CRZ27Q
D1010 RECTIFIER DIODE BA158 NDQZ000BA158
D1011 RECTIFIER DIODE BA158 NDQZ000BA158
D1012 RECTIFIER DIODE BA159 NDQZ000BA159
D1014 RECTIFIER DIODE BA158 NDQZ000BA158
D1020 SCHOTTKY BARRIER DIODE SB240-B/P NDQZ000SB240
D1031 WIRE CP STP-S-0.60 XZ40F0REN002
D1036 RECTIFIER DIODE 1N4005 NDQZ001N4005
D1037 RECTIFIER DIODE 1N4005 NDQZ001N4005
D1038 WIRE CP STP-S-0.60 XZ40F0REN002
D1058 RECTIFIER DIODE 1N4005 NDQZ001N4005
D2001 LED(GREEN) LTL-1CHGE NPQZLTL1CHGE
D2002 LED(GREEN) LTL-1CHGE NPQZLTL1CHGE
ICSIC301 IC Y/C/A LA71208EB-3E QSCA0R0SY007
IC451 IC HIFI AN3663FBP-TV QSZBA0RMS035
IC501 IC SYSCON MN101D08DZL QSAA0R0MS031
IC751 IC SWITCH 4053L-S16-R NSZBA0TUTC04
IC1001# PHOTOCOUPLER EL817B NPEB000EL817
IC1002 IC REGULATOR UTC0532 NSCA0T02H005
IC1003 IC SWITCHING FA5640N-C6-TE3/SOP-8 QSCA0T0FD007
IC1004 IC REGULATOR UTC0532 NSCA0T02H005
IC1201 IC OP AMP UTC4558TE/SOP/8PIN NSCA0T02H002
IC1402 DRIVER FOR DVD MM1637XVBE QSZBA0TMM102
IC1801 IC CCD IC AN13410A QSCA0T0MS052
COILSL009 RADIAL TYPE CHOKE COIL CW68-470K-
841040NPLLBD00PKV023
L251 WIRE CP STP-S-0.60 XZ40F0REN002
L303 INDUCTOR AXIAL AL02TA101K LLXAKTABC101
L304 RADIAL TYPE CHOKE COIL CW68-470K-841040NP
LLBD00PKV023
L400 CHIP INDUCTOR(22UH) LB2518T220M LLC220MTU029
L421 INDUCTOR RADIAL AL35RD470K LLF470ABC001
L451 WIRE CP STP-S-0.60 XZ40F0REN002
Ref. No. Description Parts No.
L502 RADIAL TYPE CHOKE COIL CW68-470K-841040NP
LLBD00PKV023
L504 WIRE CP STP-S-0.60 XZ40F0REN002
L506 WIRE CP STP-S-0.60 XZ40F0REN002
L751 INDUCTOR AXIAL AL02TA101K LLXAKTABC101
L771 WIRE CP STP-S-0.60 XZ40F0REN002
L1001# COIL LINE FILTER JLB20164 LLEG0Z0XB030
L1002 WIRE CP STP-S-0.60 XZ40F0REN002
L1020 RADIAL TYPE CHOKE COIL CW68-470K-841040NP
LLBD00PKV023
L1350 WIRE CP STP-S-0.60 XZ40F0REN002
L1351 CHIP INDUCTOR LK1608R47K-T LLACKB3TUR47
L1522 INDUCTOR RADIAL AL35RD470K LLF470ABC001
L1801 RES CHIP 1608 1/10W 0 RRXA000HH014
L1802 RES CHIP 1608 1/10W 0 RRXA000HH014
L2001 INDUCTOR AXIAL AL02TA101K LLXAKTABC101
TRANSISTORSQ052 NPN TRANSISTOR RC103S NQSZ00RC103S
Q055 NPN TRANSISTOR 2SC5343G-AT NQSG02SC5343
Q056 NPN TRANSISTOR ST 2SC3203Y NQSY02SC3203
Q063 PNP TRANSISTOR ST 2SA1266G NQSGT2SA1266
Q064 NPN TRANSISTOR ST 2SC3199G NQSGT2SC3199
Q302 NPN TRANSISTOR SMD MMBTSC3879Y NQ1YBTSC3879
Q391 PNP TRANSISTOR ST 2SA1266G NQSGT2SA1266
Q421 PNP TRANSISTOR ST 2SA1266G NQSGT2SA1266
Q422 NPN TRANSISTOR ST 2SC3203Y NQSY02SC3203
Q425 PNP TRANSISTOR RA103S NQSZ00RA103S
Q426 CHIP TRANSISTOR RN1511(TE85R.F) QQ2Z0RN1511F
Q428 NPN TRANSISTOR SMD MMBTSC3875Y NQ1YBTSC3875
Q429 NPN TRANSISTOR SMD MMBTSC3875Y NQ1YBTSC3875
Q430 PNP TRANSISTOR SMD MMBTSA1504G NQ1GBTSA1504
Q432 NPN TRANSISTOR MMBTRC103SS NQ1ZTRC103SS
Q501 NPN TRANSISTOR ST 2SC3199L NQSLT2SC3199
Q506 PHOTO TRANSISTOR PT204-6B-12 NPWZT2046B12
Q1002 MOS FET TK5A50D(S4FND X S) QEEZTK5A50DS
Q1004 NPN TRANSISTOR ST 2SC3203Y NQSY02SC3203
Q1005 NPN TRANSISTOR MMBTRC101SS NQ1ZTRC101SS
Q1006 PNP TRANSISTOR ST 2SA1266G NQSGT2SA1266
Q1011 NPN TRANSISTOR MMBTSC3265Y NQ1YBTSC3265
Q1101 NPN TRANSISTOR SMD MMBTSC3875Y NQ1YBTSC3875
Q1106 NPN TRANSISTOR SMD MMBTSC3875L NQ1LBTSC3875
Q1201 NPN TRANSISTOR ST 2SC3199G NQSGT2SC3199
Q1202 NPN TRANSISTOR ST 2SC3199G NQSGT2SC3199
Q1204 PNP TRANSISTOR ST 2SA1266G NQSGT2SA1266
Q1301 PNP TRANSISTOR SMD MMBTSA1504G NQ1GBTSA1504
Q1351 NPN TRANSISTOR ST 2SC3199G NQSGT2SC3199
Q1802 PNP TRANSISTOR SMD MMBTSA1504G NQ1GBTSA1504
Q1803 NPN TRANSISTOR SMD MMBTSC3875Y NQ1YBTSC3875
Q2002 NPN TRANSISTOR SMD MMBTSC3875Y NQ1YBTSC3875
Q2013 NPN TRANSISTOR SMD MMBTSC3875Y NQ1YBTSC3875
Q2014 NPN TRANSISTOR MMBTRC103SS NQ1ZTRC103SS
RESISTORSR041 RES CHIP 1608 1/10W J 1.0 k RRXA102HH013
R042 RES CHIP 1608 1/10W J 820 RRXA821HH013
R043 RES CHIP 1608 1/10W F 22.0 k RTW2202HH008
R044 RES CHIP 1608 1/10W F 1.50 k RTW1501HH008
R045 RES CHIP 1608 1/10W F 22.0 k RTW2202HH008
R046 RES CHIP 1608 1/10W J 680 RRXA681HH013
R056 RES CARBON FILM 1/4W J 1.0 k RCJ102PAK001
R057 RES CHIP 3216 1/4W J 150 RRX4151HH034
R058 RES CHIP 1608 1/10W J 180 RRXA181HH013
R063 WIRE CP STP-S-0.60 XZ40F0REN002
R066 RES CARBON FILM 1/4W J 470 RCJ471PAK001
Ref. No. Description Parts No.
20131216 1-21-4 E8E6EEL
R067 RES CHIP 1608 1/10W J 4.7 k RRXA472HH013
R068 RES CHIP 1608 1/10W J 4.7 k RRXA472HH013
R069 RES CHIP 1608 1/10W J 47 k RRXA473HH013
R073 RES CARBON FILM 1/4W J 10 k RCJ103PAK001
R075 RES CARBON FILM 1/4W J 4.7 k RCJ472PAK001
R092 RES CARBON FILM 1/4W J 560 RCJ561PAK001
R095 RES CARBON FILM 1/4W J 560 RCJ561PAK001
R301 RES CHIP 1608 1/10W J 10 k RRXA103HH013
R302 RES CHIP 1608 1/10W J 12 k RRXA123HH013
R304 RES CHIP 1608 1/10W J 1.2 k RRXA122HH013
R306 RES CHIP 1608 1/10W J 3.9M RRXA395HH013
R310 RES CHIP 1608 1/10W J 4.7 k RRXA472HH013
R311 RES CHIP 1608 1/10W J 1.8 k RRXA182HH013
R316 RES CHIP 1608 1/10W J 2.2 k RRXA222HH013
R317 RES CHIP 1608 1/10W J 8.2 k RRXA822HH013
R318 RES CHIP 1608 1/10W 0 RRXA000HH014
R319 RES CHIP 1608 1/10W 0 RRXA000HH014
R320 RES CHIP 1608 1/10W 0 RRXA000HH014
R321 RES CHIP 1608 1/10W J 10 k RRXA103HH013
R322 RES CHIP 1608 1/10W J 18 k RRXA183HH013
R323 RES CHIP 1608 1/10W J 10 k RRXA103HH013
R324 RES CHIP 1608 1/10W J 18 k RRXA183HH013
R327 RES CHIP 1608 1/10W F 1.10 k RTW1101HH008
R341 RES CHIP 1608 1/10W J 33 k RRXA333HH013
R343 RES CHIP 1608 1/10W J 3.3 k RRXA332HH013
R344 RES CHIP 1608 1/10W J 47 k RRXA473HH013
R391 RES CARBON FILM 1/4W J 680 RCJ681PAK001
R392 RES CARBON FILM 1/4W J 680 RCJ681PAK001
R397 RES CHIP 1608 1/10W J 100 RRXA101HH013
R401 RES CHIP 1608 1/10W J 6.8 k RRXA682HH013
R402 RES CHIP 1608 1/10W J 8.2 k RRXA822HH013
R407 RES CHIP 1608 1/10W 0 RRXA000HH014
R408 RES CHIP 1608 1/10W 0 RRXA000HH014
R409 RES CHIP 1608 1/10W J 8.2 k RRXA822HH013
R410 RES CHIP 1608 1/10W J 12 k RRXA123HH013
R411 RES CHIP 1608 1/10W J 330 k RRXA334HH013
R412 RES CHIP 1608 1/10W F 150 RTW1500HH008
R413 RES CHIP 1608 1/10W J 22 k RRXA223HH013
R414 RES CHIP 1608 1/10W J 910 RRXA911HH013
R415 RES CHIP 1608 1/10W J 2.2 k RRXA222HH013
R416 RES CHIP 1608 1/10W J 10 k RRXA103HH013
R421 RES CARBON FILM 1/4W J 6.8 k RCJ682PAK001
R422 RES CHIP 1608 1/10W J 22 k RRXA223HH013
R424 RES CARBON FILM 1/4W J 47 k RCJ473PAK001
R425 RES CARBON FILM 1/4W J 100 RCJ101PAK001
R426 RES CARBON FILM 1/4W J 820 RCJ821PAK001
R450 RES CHIP 1608 1/10W J 39 k RRXA393HH013
R451 RES CHIP 1608 1/10W J 18 k RRXA183HH013
R452 RES CHIP 1608 1/10W J 4.7 k RRXA472HH013
R453 RES CHIP 1608 1/10W J 47 k RRXA473HH013
R454 RES CHIP 1608 1/10W J 6.8 k RRXA682HH013
R455 RES CHIP 1608 1/10W J 47 k RRXA473HH013
R456 RES CHIP 1608 1/10W J 6.8 k RRXA682HH013
R460 RES CHIP 1608 1/10W J 1.8 k RRXA182HH013
R461 RES CHIP 1608 1/10W J 4.7 k RRXA472HH013
R462 RES CHIP 1608 1/10W 0 RRXA000HH014
R463 RES CHIP 1608 1/10W J 47 k RRXA473HH013
R464 RES CHIP 1608 1/10W J 6.8 k RRXA682HH013
R465 RES CHIP 1608 1/10W J 47 k RRXA473HH013
R466 RES CHIP 1608 1/10W J 6.8 k RRXA682HH013
R468 RES CHIP 1608 1/10W J 120 k RRXA124HH013
R469 RES CHIP 1608 1/10W J 1.0 k RRXA102HH013
R471 RES CHIP 1608 1/10W J 1.0 k RRXA102HH013
Ref. No. Description Parts No.
R476 RES CHIP 1608 1/10W J 22 k RRXA223HH013
R477 RES CHIP 1608 1/10W J 22 k RRXA223HH013
R478 RES CHIP 1608 1/10W J 1.0 k RRXA102HH013
R479 RES CHIP 1608 1/10W J 1.0 k RRXA102HH013
R488 RES CHIP 1608 1/10W J 10 k RRXA103HH013
R490 RES CHIP 1608 1/10W J 2.2 k RRXA222HH013
R491 RES CHIP 1608 1/10W 0 RRXA000HH014
R502 RES CHIP 1608 1/10W J 2.2 k RRXA222HH013
R503 RES CHIP 1608 1/10W J 1.0 k RRXA102HH013
R504 RES CHIP 1608 1/10W J 100 k RRXA104HH013
R507 RES CHIP 1608 1/10W J 220 RRXA221HH013
R511 RES CHIP 1608 1/10W J 39 k RRXA393HH013
R512 RES CHIP 1608 1/10W J 100 RRXA101HH013
R518 RES CHIP 1608 1/10W J 220 k RRXA224HH013
R523 RES CHIP 1608 1/10W J 2.2 k RRXA222HH013
R524 RES CHIP 1608 1/10W J 10 k RRXA103HH013
R525 RES CHIP 1608 1/10W J 10 k RRXA103HH013
R526 RES CHIP 1608 1/10W J 1.0 k RRXA102HH013
R527 RES CHIP 1608 1/10W J 1.0 k RRXA102HH013
R528 RES CARBON FILM 1/4W J 10 k RCJ103PAK001
R530 RES CHIP 1608 1/10W J 10 k RRXA103HH013
R531 RES CARBON FILM 1/4W G 4.7 k RCG472PAK001
R532 RES CARBON FILM 1/4W G 1.5 k RCG152PAK001
R533 RES CARBON FILM 1/4W G 22 k RCG223PAK001
R534 RES CARBON FILM 1/4W G 470 RCG471PAK001
R535 RES CARBON FILM 1/4W G 10 k RCG103PAK001
R536 RES CARBON FILM 1/4W G 3.6 k RCG362PAK001
R537 RES CHIP 1608 1/10W J 33 k RRXA333HH013
R540 RES CHIP 1608 1/10W J 330 k RRXA334HH013
R541 RES CHIP 1608 1/10W J 330 k RRXA334HH013
R542 RES CARBON FILM 1/4W J 270 RCJ271PAK001
R543 RES CHIP 1608 1/10W J 4.7 k RRXA472HH013
R544 RES CHIP 1608 1/10W J 18 k RRXA183HH013
R545 RES CHIP 1608 1/10W J 10 k RRXA103HH013
R546 RES CHIP 1608 1/10W J 10 k RRXA103HH013
R551 RES CHIP 1608 1/10W J 10 k RRXA103HH013
R552 RES CHIP 1608 1/10W J 1.0 k RRXA102HH013
R559 RES CHIP 1608 1/10W 0 RRXA000HH014
R563 RES CHIP 1608 1/10W J 1.0 k RRXA102HH013
R566 RES CARBON FILM 1/4W J 1.2 k RCJ122PAK001
R568 RES CARBON FILM 1/4W J 1.2 k RCJ122PAK001
R573 RES CARBON FILM 1/4W J 680 RCJ681PAK001
R574 RES CARBON FILM 1/4W J 680 RCJ681PAK001
R580 RES CARBON FILM 1/4W J 1.2 k RCJ122PAK001
R585 RES CHIP 1608 1/10W J 1.0 k RRXA102HH013
R586 RES CHIP 1608 1/10W J 1.2 k RRXA122HH013
R587 RES CHIP 1608 1/10W J 1.5 k RRXA152HH013
R588 RES CHIP 1608 1/10W J 2.2 k RRXA222HH013
R590 RES CHIP 1608 1/10W J 1.0 k RRXA102HH013
R591 RES CHIP 1608 1/10W J 1.2 k RRXA122HH013
R593 RES CHIP 1608 1/10W J 1.8 k RRXA182HH013
R594 RES CHIP 1608 1/10W J 1.8 k RRXA182HH013
R606 RES CHIP 1608 1/10W J 10 k RRXA103HH013
R607 RES CARBON FILM 1/4W J 10 k RCJ103PAK001
R610 RES CHIP 1608 1/10W J 10 k RRXA103HH013
R612 RES CHIP 1608 1/10W J 10 k RRXA103HH013
R618 RES CHIP 1608 1/10W J 10 k RRXA103HH013
R619 RES CHIP 1608 1/10W J 10 k RRXA103HH013
R640 RES CHIP 1608 1/10W J 1.0 k RRXA102HH013
R752 RES CHIP 1608 1/10W J 75 RRXA750HH013
R753 RES CHIP 1608 1/10W J 75 RRXA750HH013
R758 RES CARBON FILM 1/4W J 75 RCJ750PAK001
R773 RES CHIP 1608 1/10W J 100 k RRXA104HH013
Ref. No. Description Parts No.
20131216 1-21-5 E8E6EEL
R774 RES CARBON FILM 1/4W J 22 k RCJ223PAK001
R775 RES CHIP 1608 1/10W J 100 k RRXA104HH013
R777 RES CARBON FILM 1/4W J 2.7 k RCJ272PAK001
R788 WIRE CP STP-S-0.60 XZ40F0REN002
R1001 RES CHIP 1608 1/10W J 100 k RRXA104HH013
R1007 RES CHIP 3216 1/4W J 220 RRX4221HH034
R1009 RES CHIP 3216 1/4W J 10 RRX4100HH034
R1010 RES CHIP 3216 1/4W J 100 RRX4101HH034
R1011 RES CHIP 3216 1/4W J 39 k RRX4393HH034
R1012 RES CHIP 3216 1/4W J 39 k RRX4393HH034
R1013 METALOXIDE RES 2W J 100 k RNB104PAK004
R1014 METALOXIDE RES 2W J 0.27OHM RNJR27PAK002
R1015 RES CHIP 3216 1/4W J 27 RRX4270HH034
R1016 RES CHIP 1608 1/10W J 100 k RRXA104HH013
R1025 RES CARBON FILM 1/4W J 10 k RCJ103PAK001
R1026 RES CARBON FILM 1/4W J 10 k RCJ103PAK001
R1044 RES CHIP 1608 1/10W J 220 k RRXA224HH013
R1068 RES CARBON FILM 1/4W J 3.9 k RCJ392PAK001
R1077 RES CARBON FILM 1/4W J 1.5 k RCJ152PAK001
R1085 RES CHIP 1608 1/10W J 100 RRXA101HH013
R1086 RES CHIP 1608 1/10W J 100 k RRXA104HH013
R1087 RES CHIP 1608 1/10W J 1.0 k RRXA102HH013
R1090 RES CHIP 1608 1/10W F 200 k RTW2003HH008
R1091 RES CHIP 1608 1/10W F 120 k RTW1203HH008
R1101 RES CHIP 1608 1/10W J 1.0 k RRXA102HH013
R1102 RES CHIP 1608 1/10W J 10 k RRXA103HH013
R1205 RES CHIP 1608 1/10W F 12.0 k RTW1202HH008
R1206 RES CHIP 1608 1/10W F 12.0 k RTW1202HH008
R1207 RES CHIP 1608 1/10W 0 RRXA000HH014
R1208 RES CHIP 1608 1/10W 0 RRXA000HH014
R1209 RES CHIP 1608 1/10W F 30.0 k RTW3002HH008
R1210 RES CHIP 1608 1/10W F 30.0 k RTW3002HH008
R1221 RES CHIP 1608 1/10W J 100 k RRXA104HH013
R1222 RES CHIP 1608 1/10W J 100 k RRXA104HH013
R1223 RES CHIP 1608 1/10W J 470 RRXA471HH013
R1224 RES CHIP 1608 1/10W J 470 RRXA471HH013
R1225 RES CHIP 1608 1/10W J 1.0 k RRXA102HH013
R1226 RES CHIP 1608 1/10W J 1.0 k RRXA102HH013
R1238 RES CHIP 1608 1/10W 0 RRXA000HH014
R1240 RES CHIP 1608 1/10W J 100 k RRXA104HH013
R1245 RES CARBON FILM 1/4W J 47 RCJ470PAK001
R1309 RES CHIP 1608 1/10W J 2.2 k RRXA222HH013
R1351 RES CHIP 1608 1/10W J 1.8 k RRXA182HH013
R1352 RES CHIP 1608 1/10W J 2.2 k RRXA222HH013
R1353 RES CHIP 1608 1/10W J 2.2 k RRXA222HH013
R1354 RES CHIP 1608 1/10W J 220 RRXA221HH013
R1355 RES CHIP 1608 1/10W J 75 RRXA750HH013
R1356 RES CHIP 1608 1/10W J 100 k RRXA104HH013
R1395 RES CARBON FILM 1/4W J 1.0 k RCJ102PAK001
R1421 RES CHIP 1608 1/10W F 130 RTW1300HH008
R1422 RES CHIP 1608 1/10W J 75 RRXA750HH013
R1441 RES CHIP 1608 1/10W F 130 RTW1300HH008
R1442 RES CHIP 1608 1/10W J 75 RRXA750HH013
R1443 RES CHIP 1608 1/10W J 75 RRXA750HH013
R1461 RES CHIP 1608 1/10W F 130 RTW1300HH008
R1462 RES CHIP 1608 1/10W J 75 RRXA750HH013
R1481 RES CHIP 1608 1/10W F 130 RTW1300HH008
R1482 RES CHIP 1608 1/10W J 75 RRXA750HH013
R1490 RES CHIP 1608 1/10W 0 RRXA000HH014
R1501 RES CHIP 1608 1/10W J 100 RRXA101HH013
R1801 RES CHIP 1608 1/10W F 56.0 k RTW5602HH008
R1803 RES CHIP 1608 1/10W J 2.7 k RRXA272HH013
R1806 RES CHIP 1608 1/10W F 120 RTW1200HH008
Ref. No. Description Parts No.
R2001 RES CHIP 1608 1/10W J 10 k RRXA103HH013
R2002 RES CHIP 1608 1/10W J 10 k RRXA103HH013
R2003 RES CHIP 1608 1/10W J 10 k RRXA103HH013
R2005 RES CHIP 1608 1/10W J 6.8 k RRXA682HH013
R2012 RES CHIP 1608 1/10W J 5.6 k RRXA562HH013
R2013 RES CHIP 1608 1/10W J 10 k RRXA103HH013
R2028 RES CHIP 1608 1/10W J 6.8 k RRXA682HH013
R2031 RES CHIP 1608 1/10W J 33 k RRXA333HH013
R2051 RES CARBON FILM 1/4W J 3.9 k RCJ392PAK001
R2052 RES CARBON FILM 1/4W J 3.9 k RCJ392PAK001
R2053 RES CARBON FILM 1/4W J 680 RCJ681PAK001
R2054 RES CARBON FILM 1/4W J 680 RCJ681PAK001
R2055 RES CHIP 1608 1/10W J 10 k RRXA103HH013
R2056 RES CHIP 1608 1/10W J 10 k RRXA103HH013
R3004 RES CHIP 3216 1/4W J 100 RRX4101HH034
SWITCHESSW502 TACT SWITCH TC-1104(H=9.5) SST0101DNG01
SW505 TACT SWITCH TC-1104(H=9.5) SST0101DNG01
SW508 TACT SWITCH TC-1104(H=9.5) SST0101DNG01
SW509 TACT SWITCH TC-1104(H=9.5) SST0101DNG01
SW511 LEAF SWITCH MXS01830MVP0 SSC0101MCE03
SW512 SWITCH ROTARY SSS-53MD-1 SSR0106KB004
SW513 TACT SWITCH TC-1104(H=9.5) SST0101DNG01
SW514 TACT SWITCH TC-1104(H=9.5) SST0101DNG01
SW515 TACT SWITCH TC-1104(H=9.5) SST0101DNG01
SW516 TACT SWITCH TC-1104(H=9.5) SST0101DNG01
SW2002 TACT SWITCH TC-1104(H=9.5) SST0101DNG01
SW2003 TACT SWITCH TC-1104(H=9.5) SST0101DNG01
SW2005 TACT SWITCH TC-1104(H=9.5) SST0101DNG01
SW2006 TACT SWITCH TC-1104(H=9.5) SST0101DNG01
MISCELLANEOUSA5 JACK BOARD(RCA) H9600UD 0VM204468
AC1001# AC CORD W/O A GND WIRE UL/CSA/1770/BLACK
WAC172ZHN004
2B9 SCOTCH TAPE WIDTH 12MM 1EZZ10416
2B11 HEAD SHIELD E8P6BUH 2VMS00065
2B15 BUSH LED(F) H3700UD 0VM409508
BC1001 BEAD INDUCTORS B29 RID 2.3X7.5X7.5T LLEF0S0XM002
F1002# TIME LAG FUSE SLT250V1.6A PDGSLB0NG162
JC06 RES CHIP 1608 1/10W 0 RRXA000HH014
JC11 RES CHIP 1608 1/10W 0 RRXA000HH014
JC30 RES CHIP 1608 1/10W 0 RRXA000HH014
JC31 RES CHIP 1608 1/10W 0 RRXA000HH014
JC781 RES CHIP 1608 1/10W 0 RRXA000HH014
JC782 RES CHIP 1608 1/10W 0 RRXA000HH014
JC802 RES CHIP 1608 1/10W 0 RRXA000HH014
JK751 RCA JACK MSP-283V-B-324NILF01 JXRL040LY141
JK752 RCA JACK MSP-293V3-324NILF(B1 JYRL060LY031
JK753 RCA JACK MSP-281V42-B(B110) JXRL010LY142
JK754 RCA JACK MSP-281V40-B(B110) JXRL010LY138
JK755 RCA JACK 1P MSP-281V31-A(B110) JYRL010LY027
JK756 RCA JACK 2P MSP-282V-12 NILF(B11 JXRL020LY121
JK1202 RCA JACK MSP-281V41-B(B110) JXRL010LY140
JK1401 S TYPE JACK MDC-050V-2.4 LF(B110 JXEL040LY003
JK1403 RCA JACK MSP-283V-B-752 NI LF JXRL040LY122
2L062 SCREW BIND BLACK_NI +B-TITE M3X8.0 M3X8 BIND HEAD+
GBHB3080
RM2001 SENSOR REMOTE RECEIVER SIRC420MH11B6A7T
USEJRS0Q0001
SA1001# VARISTOR SVR10D241KA78BE NVQZVR10D241
T1001# TRANS POWER BCK-28-9853 LTT2PC0XB090
TP301 WIRE CP STP-S-0.60 XZ40F0REN002
TP302 WIRE CP STP-S-0.60 XZ40F0REN002
Ref. No. Description Parts No.
20131216 1-21-6 E8E6EEL
POWER SW CBA
DVD OPEN/CLOSE CBA
SENSOR CBA
TP506 WIRE CP STP-S-0.60 XZ40F0REN002
TP507 WIRE CP STP-S-0.60 XZ40F0REN002
TP513 WIRE CP STP-S-0.60 XZ40F0REN002
TP751 WIRE CP STP-S-0.60 XZ40F0REN002
TP753 WIRE CP STP-S-0.60 XZ40F0REN002
TP754 WIRE CP STP-S-0.60 XZ40F0REN002
VR501 CARBON P.O.T. VZ067TL1 B104 PB(F) VRCB104HH014
W002 FFC CABLE 26P FFC/P1.00/230 WX1H9600-002
W004 WIRE ASSEMBLY FFC 15 193 WHITE WX1E8A00-004
X301 XTAL 3.579545MHz(20PPM) FXC355LCHE01
X501 XTAL 14.31818MHz HC-49/S FHX146CMT001
X502 RESONATOR XTAL 32.768kHz QTF38-32.768K125P15L
FXC323LQUA03
Ref. No. Description Part No.
POWER SW CBA (MCV-B)Consists of the following:
----------
DIODED561 LED(RED) LTL-4222 NPQZ0LTL4222
SWITCHSW518 TACT SWITCH TC-1104(H=9.5) SST0101DNG01
MISCELLANEOUS2B13 BUSH LED(E) H1600UD 0VM408832
W013 WIRE ASSEMBLY 4P 04 60 GRAY WX1E8C6A-001
Ref. No. Description Part No.
DVD OPEN/CLOSE CBA (MCV-C)Consists of the following:
----------
SWITCHSW2001 TACT SWITCH TC-1104(H=9.5) SST0101DNG01
MISCELLANEOUSW011 WIRE ASSEMBLY 02 130 GRAY WX1E8A00-001
Ref. No. Description Part No.
SENSOR CBAConsists of the following:
1VSA13493
TRANSISTORSQ503 PHOTO TRANSISTOR PT204-6B-12 NPWZT2046B12
Q504 PHOTO TRANSISTOR PT204-6B-12 NPWZT2046B12
Ref. No. Description Parts No.
© 2013 Funai Electric Co., Ltd.
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded or stored in any storage medium, in any form or for any purpose without the express prior written consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content herein without the obligation to notify any person or organization of such changes.
with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the express written consent of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing contained in this manual should be construed as granting, by implication or otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law.
DVP3355V/F7E8E6EUH
2013-12-27