SERVICE MANUAL - Canon Globaldownloads.canon.com/ir-advance_bw/Super_G3_Fax_Board-AF1_SM_… · This manual has been issued by Canon Inc. fo r qualified persons to learn technical

SERVICEMANUAL

Super G3 Fax Board-AF1

COPYRIGHT ©2010 CANON INC. CANON Super G3 Fax Board-AF1 REV. 0 PRINTED IN U.S.A.

REV. 0June 9, 2010

ApplicationThis manual has been issued by Canon Inc. for qualified persons to learn technical theory, installation, maintenance, and repair

of products. This manual covers all localities where the products are sold. For this reason, there may be information in this

manual that does not apply to your locality.

CorrectionsThis manual may contain technical inaccuracies or typographical errors due to improvements or changes in products. When

changes occur in applicable products or in the contents of this manual, Canon will release technical information as the need

arises. In the event of major changes in the contents of this manual over a long or short period, Canon will issue a new edition

of this manual.

The following paragraph does not apply to any countries where such provisions are inconsistent with local law.

TrademarksThe product names and company names used in this manual are the registered trademarks of the individual companies.

CopyrightThis manual is copyrighted with all rights reserved. Under the copyright laws, this manual may not be copied, reproduced or

translated into another language, in whole or in part, without the written consent of Canon Inc.

CautionUse of this manual should be strictly supervised to avoid disclosure of confidential information.

COPYRIGHT © 2001 CANON INC.Printed in Japan

Introduction

i

Symbols UsedThis documentation uses the following symbols to indicate special information:

Symbol Description

Indicates an item of a non-specific nature, possibly classified as Note, Caution, or Warning.

Indicates an item requiring care to avoid electric shocks.

Indicates an item requiring care to avoid combustion (fire).

Indicates an item prohibiting disassembly to avoid electric shocks or problems.

Indicates an item requiring disconnection of the power plug from the electric outlet.

Indicates an item intended to provide notes assisting the understanding of the topic in question.

Indicates an item of reference assisting the understanding of the topic in question.

Provides a description of a service mode.

Provides a description of the nature of an error indication.

Memo

REF.

Introduction

ii

The following rules apply throughout this Service Manual:1. Each chapter contains sections explaining the purpose of specific functions and the relationship between electrical and mechanical systems with refer-

ence to the timing of operation.In the diagrams, represents the path of mechanical drive; where a signal name accompanies the symbol , the arrow indicates thedirection of the electric signal.The expression "turn on the power" means flipping on the power switch, closing the front door, and closing the delivery unit door, which results insupplying the machine with power.

2. In the digital circuits, '1'is used to indicate that the voltage level of a given signal is "High", while '0' is used to indicate "Low".(The voltage value,however, differs from circuit to circuit.) In addition, the asterisk (*) as in "DRMD*" indicates that the DRMD signal goes on when '0'.In practically all cases, the internal mechanisms of a microprocessor cannot be checked in the field. Therefore, the operations of the microprocessorsused in the machines are not discussed: they are explained in terms of from sensors to the input of the DC controller PCB and from the output of theDC controller PCB to the loads.

The descriptions in this Service Manual are subject to change without notice for product improvement or other purposes, and major changes will be com-municated in the form of Service Information bulletins.All service persons are expected to have a good understanding of the contents of this Service Manual and all relevant Service Information bulletins and beable to identify and isolate faults in the machine."

Contents

Contents

Chapter 1 Specifications

1.1 Product Specifications ................................................................................................................................... 1- 11.1.1 Product Specifications ............................................................................................................................ 1- 1

Chapter 2 Installation

2.1 Unpacking and Checking the Components ................................................................................................ 2- 12.1.1 Checking the Contents............................................................................................................................ 2- 1

2.2 Installation Procedure .................................................................................................................................... 2- 22.2.1 Check Items when Turning OFF the Main Power .............................................................................. 2- 22.2.2 Install the FAX Unit .................................................................................................................................. 2- 22.2.3 Install the Speaker Unit........................................................................................................................... 2- 32.2.4 After the Installation................................................................................................................................. 2- 5

2.3 Checking the Operation ................................................................................................................................. 2- 72.3.1 Type Settings............................................................................................................................................ 2- 72.3.2 Basic Settings........................................................................................................................................... 2- 72.3.3 FAX Communication Test ...................................................................................................................... 2- 7

Chapter 3 Functions

3.1 Basic Construction.......................................................................................................................................... 3- 13.1.1 Overview ................................................................................................................................................... 3- 1

Chapter 4 Parts Replacement Procedure

4.1 Electrical System ............................................................................................................................................ 4- 14.1.1 Modular PCB ............................................................................................................................................. 4- 1

4.1.1.1 Removing the Modular PCB ........................................................................................................... 4- 1

Chapter 5 Service Mode

5.1 Outline .............................................................................................................................................................. 5- 15.1.1 Using Service Mode ................................................................................................................................ 5- 1

5.2 Setting of Bit Switch (SSSW) ........................................................................................................................ 5- 25.2.1 Outline ........................................................................................................................................................ 5- 2

5.2.1.1 Bit Switch Composition .................................................................................................................... 5- 25.2.2 SSSW-SW01............................................................................................................................................. 5- 2

5.2.2.1 Functional Construction ................................................................................................................... 5- 25.2.2.2 Detailed Discussions of Bit 0 .......................................................................................................... 5- 25.2.2.3 Detailed Discussions of Bit 1 .......................................................................................................... 5- 2

5.2.3 SSSW-SW03............................................................................................................................................. 5- 35.2.3.1 Functional Construction ................................................................................................................... 5- 35.2.3.2 Detailed Discussions of Bit 1 .......................................................................................................... 5- 3

Contents

5.2.3.3 Detailed Discussions of Bits 4, 5, and 6........................................................................................ 5- 35.2.3.4 Detailed Discussions of Bit 7 .......................................................................................................... 5- 3

5.2.4 SSSW-SW04............................................................................................................................................. 5- 45.2.4.1 Detailed Discussions of Bit 2 .......................................................................................................... 5- 45.2.4.2 Detailed Discussions of Bit 3 .......................................................................................................... 5- 45.2.4.3 Detailed Discussions of Bit 4 .......................................................................................................... 5- 4

5.2.5 SSSW-SW05............................................................................................................................................. 5- 45.2.5.1 Functional Construction ................................................................................................................... 5- 45.2.5.2 Detailed Discussions of Bit 1 .......................................................................................................... 5- 45.2.5.3 Detailed Discussions of Bit 2 .......................................................................................................... 5- 45.2.5.4 Detailed Discussions of Bit 3 .......................................................................................................... 5- 45.2.5.5 Detailed Discussions of Bit 4 .......................................................................................................... 5- 4

5.2.6 SSSW-SW12............................................................................................................................................. 5- 55.2.6.1 Functional Construction ................................................................................................................... 5- 5

5.2.7 SSSW-SW14............................................................................................................................................. 5- 65.2.7.1 Functional Construction ................................................................................................................... 5- 65.2.7.2 Detailed Discussions of Bit 2 .......................................................................................................... 5- 65.2.7.3 Detailed Discussions of Bit 4 .......................................................................................................... 5- 6



5.2.10 SSSW-SW26........................................................................................................................................... 5- 75.2.10.1 Functional Construction ................................................................................................................. 5- 75.2.10.2 Functional Construction ................................................................................................................. 5- 75.2.10.3 Detailed Discussions of Bit 2 ........................................................................................................ 5- 75.2.10.4 Detailed Discussions of Bit 7 ........................................................................................................ 5- 7

5.2.11 SSSW-SW28........................................................................................................................................... 5- 75.2.11.1 Functional Construction ................................................................................................................. 5- 75.2.11.2 Detailed Discussions of Bit 0 ........................................................................................................ 5- 75.2.11.3 Detailed Discussions of Bit 1 ........................................................................................................ 5- 75.2.11.4 Detailed Discussions of Bit 2 ........................................................................................................ 5- 75.2.11.5 Detailed Discussions of Bit 3 ........................................................................................................ 5- 75.2.11.6 Detailed Discussions of Bit 4 ........................................................................................................ 5- 85.2.11.7 Detailed Discussions of Bit 5 ........................................................................................................ 5- 8

5.2.12 SSSW-SW30........................................................................................................................................... 5- 95.2.12.1 Functional Construction ................................................................................................................. 5- 95.2.12.2 Detailed Discussions of Bit 5 ........................................................................................................ 5- 95.2.12.3 Detailed Discussions of Bit 6 ........................................................................................................ 5- 9

5.3 Setting of Menu Switch (MENU)................................................................................................................. 5- 105.3.1 <005: NL Equalizer>.............................................................................................................................. 5- 105.3.2 <006: Telephone Line Monitor> .......................................................................................................... 5- 105.3.3 <007: ATT Transmission Level> ......................................................................................................... 5- 105.3.4 <008: V.34 Modulation Speed Upper Limit> ..................................................................................... 5- 105.3.5 <009: V.34 Data Speed Upper Limit> ................................................................................................ 5- 10

5.4 Setting of Numeric Parameter (NUMERIC Param.) ................................................................................ 5- 105.4.1 <002: RTN transmission condition (1)><003: RTN transmission condition (2)><004: RTN

Contents

transmission condition (3)> ........................................................................................................................5- 105.4.2 <005: NCC pause length (pre-ID code)>............................................................................................5- 105.4.3 <006: NCC pause length (post-ID code)> ..........................................................................................5- 105.4.4 <007: pre-pause length at time of ring>..............................................................................................5- 105.4.5 <009: number of comparison digits of source telephone number and target telephone number> 5-

105.4.6 <010: line connection identification length> .......................................................................................5- 115.4.7 <011: T.30 T1 timer (for reception)> ...................................................................................................5- 115.4.8 <013: T.30 EOL timer> ..........................................................................................................................5- 115.4.9 <027: V.21 low-speed flag preamble identification length> .............................................................5- 11

5.5 Setting of Printer Functions (PRINTER) ....................................................................................................5- 125.5.1 Setting of Bit Switch (SSSW) ................................................................................................................5- 12

5.5.1.1 SSSW-SW05....................................................................................................................................5- 125.5.1.2 SSSW-SW06....................................................................................................................................5- 12

5.5.2 Setting of Numeric Parameter (NUMERIC Param.) ..........................................................................5- 135.5.2.1 Numerical Parameter Composition...............................................................................................5- 135.5.2.2 <001: printing upon reception of extra-length image> ...............................................................5- 135.5.2.3 <004: leading edge margin> ..........................................................................................................5- 135.5.2.4 <005: trailing edge margin> ...........................................................................................................5- 13

5.6 Initialization of Set Value (CLEAR).............................................................................................................5- 145.6.1 Overview ..................................................................................................................................................5- 14

5.7 Test Mode (TEST).........................................................................................................................................5- 155.7.1 MODEM Test ...........................................................................................................................................5- 15

5.7.1.1 Relay Test (RELAY-1) ....................................................................................................................5- 155.7.1.2 Frequency Test (FREQ) .................................................................................................................5- 155.7.1.3 G3 Signal Transmission Test (G3 Tx)..........................................................................................5- 165.7.1.4 DTMF Transmission Test ...............................................................................................................5- 175.7.1.5 V.34 G3 Signal Transmission Test (V34G3Tx) ..........................................................................5- 17

5.7.2 Function Test ...........................................................................................................................................5- 185.7.2.1 4800-bps Signal Transmission Test .............................................................................................5- 18

5.8 Service Report (REPORT)...........................................................................................................................5- 185.8.1 System Data List ....................................................................................................................................5- 185.8.2 System Dump List ..................................................................................................................................5- 205.8.3 Error Transmission Report....................................................................................................................5- 22

Chapter 6 Error Code

6.1 User Error Code...............................................................................................................................................6- 16.1.1 User Error Code........................................................................................................................................6- 1

6.2 Service Error Code..........................................................................................................................................6- 26.2.1 Service Error Code...................................................................................................................................6- 2

Chapter 1 Specifications

Contents

Contents

1.1 Product Specifications ................................................................................................................................................... 1-11.1.1 Product Specifications.................................................................................................................................................................. 1-1

Chapter 1

1-1

1.1 Product Specifications

1.1.1 Product Specifications0025-3175

T-1-1

Item Description

Communication G3

Line type Subscriber line (PSTN)

Modulation <G3 image signal>ITU-T V.27ter (2.4 Kbps, 4.8 Kbps)ITU-T V.29 (7.2 Kbps, 9.6 Kbps)ITU-T V.17 (TC 7.2 Kbps, TC 9.6 Kbps, 12 Kbps, 14.4 Kbps)ITU-T V.34 (2.4 Kbps, 4.8 Kbps, 7.2 Kbps, 9.6 Kbps, 12 Kbps, 14.4 Kbps, 16.8 Kbps, 19.2 Kbps, 21.6 Kbps, 24 Kbps, 26.4 Kbps, 28.8 Kbps, 31.2 Kbps, 33.6 Kbps)<G3 procedure signal>ITU-T V.21 No.2 (300 bps)ITU-T V.8, V.34 (300 bps)

Transmission speed 33.6 Kbps, 31.2 Kbps, 28.8 Kbps, 23.4 Kbps, 24 Kbps, 21.6 Kbps, 19.2 Kbps, 16.8 Kbps, 14.4 Kbps, 12 Kbps, TC 9.6 Kbps, TC 7.2 Kbps, 9.6 Kbps, 7.2 Kbps, 4.8 Kbps, 2.4 Kbpsauto fallback function

Coding method JBIG, MMR, MR, MH

G3-specific abridged procedure no

Modem IC conexant SFX336

Error correction ITU-T ECM

Transmission original size A3, A4, A4R, A5, A5R, B4, B5, B5R, LTR, LTRR, LGL, 11x17, STMT, STMTRADF: double-sided originals accepted

Scanning line density Standard (200 x 100 dpi): 8 dots/mm x 3.85 lines/mmFine (200 x 200 dpi):8 dots/mm x 7.7 lines/mmSuper Fine (200 x 400 dpi): 8 dots/mm x 15.4 lines/mmUltra Fine (400 x 400 dpi): 16 dots/mm x 15.4 lines/mm

Halftone 256 gradations

Recording unit maximum reception size: A3 (297 mm x 420 mm)scanning line density: 600 dpi x 600 dpi

Memory image memory: 3700 prints (Canon Fax Standard Chart No.1)memory type: hard disk (image area of 6.4 GB)storage: JBIG

Extension telephone connection no

Answering machine connection no

Fax/Tel switch-over no

Quick Direct Transmission yes

Transmission Header(Add Remote Name on Header SW)

yes

Remote reception no

Polling (F code) no

Memory box yes

Password reception yes

Machine telephone No. transmission yes

User abbreviation transmission yes

Dual access 64 (maximum number of reservations)

Broadcasting 256 targets (maximum number of targets)64 target(maximum number of targets by 10 key dialing)

Chapter 2 Installation

Contents

Contents

2.1 Unpacking and Checking the Components.................................................................................................................... 2-12.1.1 Checking the Contents ................................................................................................................................................................. 2-1

2.2 Installation Procedure .................................................................................................................................................... 2-22.2.1 Check Items when Turning OFF the Main Power ....................................................................................................................... 2-22.2.2 Install the FAX Unit..................................................................................................................................................................... 2-22.2.3 Install the Speaker Unit ................................................................................................................................................................ 2-32.2.4 After the Installation..................................................................................................................................................................... 2-5

2.3 Checking the Operation ................................................................................................................................................. 2-72.3.1 Type Settings................................................................................................................................................................................ 2-72.3.2 Basic Settings ............................................................................................................................................................................... 2-72.3.3 FAX Communication Test ........................................................................................................................................................... 2-7

Chapter 2

2-1

2.1 Unpacking and Checking the Components

2.1.1 Checking the Contents0024-7872

F-2-1

<CD/Guides>- FAX Driver CD- FCC/IC sheet (only for USA)- Notice for Connecting the Telephone Line sheet (only for Europe)

[1] Fax Unit 1pc. [2] Speaker Holder 1pc.

[3] Speaker Unit 1pc. [4] Modular Cover (only for Europe) 1pc.

[5] Modular Label 1pc. [6] Screw (P Tightening; M4x10) 2pc.

[7] Screw (TP; M3x6) 4pc. [8] Telephone Cord (2 contact type) 1pc.

[9] Telephone Cord (6 contact type) (only for Europe)

1pc. [10] PTT Plug (only for Europe) 3pc.

[11] PTT Cable (only for Asia) 1pc. [12] Approval Label 1pc.

Chapter 2

2-2

2.2 Installation Procedure

2.2.1 Check Items when Turning OFF the Main Power0024-7704

Check that the main power switch is OFF.1) Turn OFF the main power switch of the host machine.2) Be sure that Control Panel Display and Main Power Lamp are both turned

OFF, and then disconnect the power plug.

2.2.2 Install the FAX Unit0024-7873

1) Free the Reader Communication Cable and the Reader Power Supply Ca-ble from the 2 Wire Saddles [1].

2) Remove the Left Rear Cover [2].- 2 Protrusions [3]

F-2-23) Remove the Rear Upper Cover [1].

- 4 Screws (RS Tightening) [2]- 3 Screws (TP) [3]

F-2-34) Remove the Face Cover [1]. (The Removed Face Cover and screw will not

be used.)- 1 Screw [2]

F-2-45) Remove packing materials from the FAX Unit.6) Install the FAX Unit [1].

- 2 Hooks [2]- 4 Screws (TP; M3x6) [3]- 2 Connectors [4]

F-2-57) Free the Speaker Cable [1] from the Wire Saddle [2], and close the Wire

Chapter 2

2-3

Saddle.

F-2-68) Connect the Speaker Cable [1] to the FAX Unit [2].

F-2-7

2.2.3 Install the Speaker Unit0024-7705

1) Remove the Right Rear Cover 2 [1].- 2 Screws [2]

F-2-82) Open the Toner Replacement Cover [1] and the Right Cover [2], and re-

move the Right Upper Cover [3].- 2 Screws [4]- 3 Protrusions [5]- 1 Boss [6]

F-2-93) Turn the Lock Lever [1], and open the Developing Assembly Pressure

Cover [2].- 1 Screw [3]

F-2-104) Remove the Link Arm [1] on the Right Cover.

- 1 E-ring [2]

Chapter 2

2-4

F-2-115) Remove the Right Shield Plate [1].

- 2 Screws [2]

F-2-126) Disconnect the 3 Cables.

- 3 Connectors [1]- 6 Wire Saddles [2]

F-2-137) Remove the Speaker Unit Base [1] and the Grounding Wire [2].

- 2 Screws (P Tightening) [3]- 1 Screw (RS Tightening) [4]

F-2-14

8) Install the Speaker Unit [1] to the Speaker Unit Base.- 3 Harness Guides [2]- 1 Connector [3]

CAUTION:Do not touch the area [1] shown in the figure. This may cause wiring disconnection.

[1]

Chapter 2

2-5

F-2-159) Place the Speaker Unit, and install the Speaker Holder [2].

- 2 Protrusions [2]- 2 Screws (P Tightening; M4x10) [3]

F-2-1610) Return the Speaker Unit Base and the Grounding Wire to their original

position.- 2 Screws (P Tightening)- 1 Screw (RS Tightening)

11) Reconnect the 3 Harnesses disconnected in step 6) to their original posi-tions.

12) Return the following parts to their original position.- Right Shield Plate- Link Arm/E-ring- Developing Assembly Pressure Cover/Lock Lever (Close)- Right Upper Cover- Toner Replacement Cover/Right Cover (Close)- Right Rear Cover 2- Controller Box (Close)

13) Install the Rear Upper Cover.

2.2.4 After the Installation0024-9688

1) Affix the appropriate Modular Label [1] by aligning it with the markingline on the cover.

CAUTION: If the tie-wrap [1] overlaps on the cable with tube [2], this may cause the tube to be ripped, so be sure to route the cable not to be overlapped by the tie-wrap [1].

MEMO:Be sure to install the 3 TP screws show in the figure below.

Chapter 2

2-6

F-2-17

2) Install the Modular Cover [1].- 1 Screw [2] (Use the screws removed in "Installing the FAX Unit" step4).)

F-2-183) Connect the PTT Plug [1] matched the field or area to the PTT Cable (6

contact type) [2].

F-2-194) Connect the end of the PTT Cable or Telephone Cord [1] to the modular

jack on the host machine, and connect the other end to the modular jackon the wall.

F-2-205) Return the Left Rear Cover to its original position, and secure the Reader

Communication Cable and the Reader Power Supply Cable in place usingthe 2 Wire Saddles.

6) Affix the following Approval Label.[1] For USA [2] For other countries

F-2-217) Connect the power plug to the outlet.

MEMO:Be sure to perform step 2) and 3) for the Europe models only.

MEMO:Do not connect the Telephone Cord (2 contact type) with the PTT Plug.

[1] [2]

Chapter 2

2-7

8) Turn ON the main power switch.

2.3 Checking the Operation

2.3.1 Type Settings0024-9697

Select the country/region of the FAX Board in Service Mode: FAX > TYPE> TYPEThis setting performs the parameter settings to match the communicationspecification of the country/region.

1) Set the TYPE of country/region to install this machine, and then press OK.- Service Mode > FAX > TYPE > TYPE

2) Turn OFF/ON the main power switch to enable this setting.

2.3.2 Basic Settings0024-7716

In this section, make only minimum settings required for FAX communica-tion.1) Set the user telephone number.

[Settings/Registration] > [Function Settings] > [Send] > [Fax Settings] >[Set Line] > [Line 1] > [Register User Telephone No.] > Enter FAXnumber > [OK]

2) Set the type of telephone line.[Settings/Registration] > [Function Settings] > [Send] > [Fax Settings] >[Set Line] > [Line 1] > [Select Line Type] > Select the line type to connect> [OK]

3) Turn OFF/ON the main power switch after setting the user telephone num-bers and the type of telephone line.

2.3.3 FAX Communication Test0024-9689

Perform communication test to check if FAX function works correctly.1) Switch the control panel display to Send/Fax display.2) Send the test document from this machine to another machine that can

handle the communication test to check that this machine can send thedata correctly.

3) Send the test document from the target to this machine to check if the ma-chine can receive the document properly.

MEMO:When "System Manager Information Settings" is set, be sure to follow the direction of user administrator in order to log in as an administrator.

Chapter 3 Functions

Contents

Contents

3.1 Basic Construction......................................................................................................................................................... 3-13.1.1 Overview ...................................................................................................................................................................................... 3-1

Chapter 3

3-1

3.1 Basic Construction

3.1.1 Overview0025-3176

This product is a FAX unit for adding FAX lines to the machine.This machine is equipped with a telephone-based communication function and an image processing function to enable a digital copier to serve as a highly functionalmulti-function fax machine.As for image transmission speed, it is capable of communicating at 33.6 kbps (max.) thanks to a modem for V.34, which comply with ITU-T standard.

F-3-1[1] Super G3 FAX Board-AF1[2] Pseudo CI PCB[3] Modular PCB (1-line)[4] Speaker

Chapter 3

3-2

FAX communication controlThe main controller in the machine executes FAX communication control.The FAX control program is loaded on the main controller and controls the G3 FAX PCB in the FAX unit.

F-3-2

Chapter 4 Parts Replacement Procedure

Contents

Contents

4.1 Electrical System ........................................................................................................................................................... 4-14.1.1 Modular PCB................................................................................................................................................................................ 4-1

4.1.1.1 Removing the Modular PCB...........................................................................................................................................................................4-1

Chapter 4

4-1

4.1 Electrical System

4.1.1 Modular PCB

4.1.1.1 Removing the Modular PCB0025-3181

1) Remove the Modular PCB. Disconnect the connectors from the Modular PCB. Remove the screws securing the Modular PCB.

F-4-1

Chapter 5 Service Mode

Contents

Contents

5.1 Outline ........................................................................................................................................................................... 5-15.1.1 Using Service Mode ..................................................................................................................................................................... 5-1

5.2 Setting of Bit Switch (SSSW)........................................................................................................................................ 5-25.2.1 Outline.......................................................................................................................................................................................... 5-2

5.2.1.1 Bit Switch Composition ..................................................................................................................................................................................5-25.2.2 SSSW-SW01 ................................................................................................................................................................................ 5-2

5.2.2.1 Functional Construction..................................................................................................................................................................................5-25.2.2.2 Detailed Discussions of Bit 0..........................................................................................................................................................................5-25.2.2.3 Detailed Discussions of Bit 1..........................................................................................................................................................................5-2

5.2.3 SSSW-SW03 ................................................................................................................................................................................ 5-35.2.3.1 Functional Construction..................................................................................................................................................................................5-35.2.3.2 Detailed Discussions of Bit 1..........................................................................................................................................................................5-35.2.3.3 Detailed Discussions of Bits 4, 5, and 6 .........................................................................................................................................................5-35.2.3.4 Detailed Discussions of Bit 7..........................................................................................................................................................................5-3

5.2.4 SSSW-SW04 ................................................................................................................................................................................ 5-45.2.4.1 Detailed Discussions of Bit 2..........................................................................................................................................................................5-45.2.4.2 Detailed Discussions of Bit 3..........................................................................................................................................................................5-45.2.4.3 Detailed Discussions of Bit 4..........................................................................................................................................................................5-4

5.2.5 SSSW-SW05 ................................................................................................................................................................................ 5-45.2.5.1 Functional Construction..................................................................................................................................................................................5-45.2.5.2 Detailed Discussions of Bit 1..........................................................................................................................................................................5-45.2.5.3 Detailed Discussions of Bit 2..........................................................................................................................................................................5-45.2.5.4 Detailed Discussions of Bit 3..........................................................................................................................................................................5-45.2.5.5 Detailed Discussions of Bit 4..........................................................................................................................................................................5-4

5.2.6 SSSW-SW12 ................................................................................................................................................................................ 5-55.2.6.1 Functional Construction..................................................................................................................................................................................5-5

5.2.7 SSSW-SW14 ................................................................................................................................................................................ 5-65.2.7.1 Functional Construction..................................................................................................................................................................................5-65.2.7.2 Detailed Discussions of Bit 2..........................................................................................................................................................................5-65.2.7.3 Detailed Discussions of Bit 4..........................................................................................................................................................................5-6

5.2.8 SSSW-SW23 ................................................................................................................................................................................ 5-65.2.8.1 Functional Construction..................................................................................................................................................................................5-65.2.8.2 Detailed Discussions of Bit 7..........................................................................................................................................................................5-6

5.2.9 SSSW-SW25 ................................................................................................................................................................................ 5-65.2.9.1 Functional Construction..................................................................................................................................................................................5-65.2.9.2 Detailed Discussions of Bit 0..........................................................................................................................................................................5-6

5.2.10 SSSW-SW26 .............................................................................................................................................................................. 5-75.2.10.1 Functional Construction................................................................................................................................................................................5-75.2.10.2 Functional Construction................................................................................................................................................................................5-75.2.10.3 Detailed Discussions of Bit 2........................................................................................................................................................................5-75.2.10.4 Detailed Discussions of Bit 7........................................................................................................................................................................5-7

5.2.11 SSSW-SW28 .............................................................................................................................................................................. 5-75.2.11.1 Functional Construction................................................................................................................................................................................5-75.2.11.2 Detailed Discussions of Bit 0........................................................................................................................................................................5-75.2.11.3 Detailed Discussions of Bit 1........................................................................................................................................................................5-75.2.11.4 Detailed Discussions of Bit 2........................................................................................................................................................................5-75.2.11.5 Detailed Discussions of Bit 3........................................................................................................................................................................5-75.2.11.6 Detailed Discussions of Bit 4........................................................................................................................................................................5-85.2.11.7 Detailed Discussions of Bit 5........................................................................................................................................................................5-8

5.2.12 SSSW-SW30 .............................................................................................................................................................................. 5-9

Contents

5.2.12.1 Functional Construction ............................................................................................................................................................................... 5-95.2.12.2 Detailed Discussions of Bit 5 ....................................................................................................................................................................... 5-95.2.12.3 Detailed Discussions of Bit 6 ....................................................................................................................................................................... 5-9

5.3 Setting of Menu Switch (MENU) ................................................................................................................................5-105.3.1 <005: NL Equalizer>.................................................................................................................................................................. 5-105.3.2 <006: Telephone Line Monitor>................................................................................................................................................ 5-105.3.3 <007: ATT Transmission Level>............................................................................................................................................... 5-105.3.4 <008: V.34 Modulation Speed Upper Limit> ............................................................................................................................ 5-105.3.5 <009: V.34 Data Speed Upper Limit> ....................................................................................................................................... 5-10

5.4 Setting of Numeric Parameter (NUMERIC Param.) ...................................................................................................5-105.4.1 <002: RTN transmission condition (1)><003: RTN transmission condition (2)><004: RTN transmission condition (3)> ..... 5-105.4.2 <005: NCC pause length (pre-ID code)> ................................................................................................................................... 5-105.4.3 <006: NCC pause length (post-ID code)> ................................................................................................................................. 5-105.4.4 <007: pre-pause length at time of ring>..................................................................................................................................... 5-105.4.5 <009: number of comparison digits of source telephone number and target telephone number>............................................. 5-105.4.6 <010: line connection identification length> ............................................................................................................................. 5-115.4.7 <011: T.30 T1 timer (for reception)>......................................................................................................................................... 5-115.4.8 <013: T.30 EOL timer>.............................................................................................................................................................. 5-115.4.9 <027: V.21 low-speed flag preamble identification length> ..................................................................................................... 5-11

5.5 Setting of Printer Functions (PRINTER) .....................................................................................................................5-125.5.1 Setting of Bit Switch (SSSW) .................................................................................................................................................... 5-12

5.5.1.1 SSSW-SW05 ................................................................................................................................................................................................ 5-125.5.1.1.1 Functional Construction........................................................................................................................................................................ 5-125.5.1.1.2 Detailed Discussions of Bits 0 and 1 .................................................................................................................................................... 5-125.5.1.1.3 Detailed Discussions of Bit 7 ............................................................................................................................................................... 5-12

5.5.1.2 SSSW-SW06 ................................................................................................................................................................................................ 5-125.5.1.2.1 Functional Construction........................................................................................................................................................................ 5-125.5.1.2.2 Detailed Discussions of Bit 5 ............................................................................................................................................................... 5-12

5.5.2 Setting of Numeric Parameter (NUMERIC Param.).................................................................................................................. 5-135.5.2.1 Numerical Parameter Composition............................................................................................................................................................... 5-135.5.2.2 <001: printing upon reception of extra-length image>................................................................................................................................. 5-135.5.2.3 <004: leading edge margin> ......................................................................................................................................................................... 5-135.5.2.4 <005: trailing edge margin> ......................................................................................................................................................................... 5-13

5.6 Initialization of Set Value (CLEAR) ...........................................................................................................................5-145.6.1 Overview .................................................................................................................................................................................... 5-14

5.7 Test Mode (TEST) .......................................................................................................................................................5-155.7.1 MODEM Test............................................................................................................................................................................. 5-15

5.7.1.1 Relay Test (RELAY-1)................................................................................................................................................................................. 5-155.7.1.2 Frequency Test (FREQ)................................................................................................................................................................................ 5-155.7.1.3 G3 Signal Transmission Test (G3 Tx).......................................................................................................................................................... 5-165.7.1.4 DTMF Transmission Test............................................................................................................................................................................. 5-175.7.1.5 V.34 G3 Signal Transmission Test (V34G3Tx) ........................................................................................................................................... 5-17

5.7.2 Function Test.............................................................................................................................................................................. 5-185.7.2.1 4800-bps Signal Transmission Test.............................................................................................................................................................. 5-18

5.8 Service Report (REPORT)...........................................................................................................................................5-185.8.1 System Data List ........................................................................................................................................................................ 5-185.8.2 System Dump List...................................................................................................................................................................... 5-205.8.3 Error Transmission Report ......................................................................................................................................................... 5-22

Chapter 5

5-1

5.1 Outline

5.1.1 Using Service Mode0025-3084

1) Press the User Mode key " " on the control panel.2) Press the keys 2 and 8 on the keypad at the same time.

3) Press the User Mode key " " on the control panel once again.The machine will indicate the accessories that are connected to it (e.g., FEEDER, FAX, BOARD).Select [FAX] to use service mode items available for the Board.

F-5-1COPIER: service mode of the host machine.FEEDER: service mode of the ADF. (*)FAX: service mode of the fax. (*)BOARD: service mode of an accessory board. (*)

*: Indicated only if installed.

For instance, in the case of #1 SSSW, the following holds true; key functions and operations are the same for all screens:

F-5-2- If you want to change 0 to 1 or 1 to 0 on a bit switch, press the desired bit (number) directly.- If you want to store a change or execute an item, press the OK key.- Use the keypad to enter a numerical value.- To return to the previous level of selection, press the Reset key.

If you changed a setting in service mode, be sure to turn off and then on the power (making sure that you first turn off the control panel switch and then the main power switch).The settings made in service mode are stored on the hard disk. The settings associated with the Board are loaded to the G3 fax control PCB only when the main power is tuned on, thus requiring you to turn it off and then on after making a change.

COPIER

FEEDER

SORTER

BOARD

FAX

SERVICE MODE LEVEL 1

<1/7> <READY>

ReportSssw Menu Num Ncu Type ISDN Print Clear Test

0 0 0 0 0 0 0 01 0 0 0 0 0 0 00 0 0 0 0 0 0 01 0 0 0 0 0 0 00 0 0 0 0 0 0 01 0 0 0 0 0 0 0

SW01SW02SW03SW04SW05SW06

0 0 0 0 0 0 0 01 0 0 0 0 0 0 0

SW07SW08

OK

Press to accept the current input.Previous Page/Next Page key

Chapter 5

5-2

5.2 Setting of Bit Switch (SSSW)

5.2.1 Outline

5.2.1.1 Bit Switch Composition0025-3086

The registration/setup items of the switch are set according to the positions of its 8 bits; the bit switch shown on the display is as follows, each bit being either 0 or 1:

F-5-3

F-5-4

5.2.2 SSSW-SW01

5.2.2.1 Functional Construction0025-3087

T-5-1

5.2.2.2 Detailed Discussions of Bit 00025-3088

Selects whether or not service error codes are output.When output is selected, service error codes are displayed and in reports.


Selects whether or not error dump lists are output.When selecting 'output', the error transmission report and the reception result report at the time of error to which the error dump list is attached are output.

Do not change service data identified as "not used"; they are set as initial settings.

Bit Function 1 0

0 service error code output not output

1 error dump list output not output

2 not used - -

3 not used - -

4 not used - -

5 not used - -

6 not used - -

7 not used - -

SW01 0 0 0 0 0 0 0 0

Bit 7 Bit 0

<1/7> <READY>


0 0 0 0 0 0 0 01 0 0 0 0 0 0 00 0 0 0 0 0 0 01 0 0 0 0 0 0 00 0 0 0 0 0 0 01 0 0 0 0 0 0 0

SW01SW02SW03SW04SW05SW06

0 0 0 0 0 0 0 01 0 0 0 0 0 0 0

SW07SW08

OK

Chapter 5

5-3

5.2.3 SSSW-SW03


T-5-2


Use it to enable/disable transmission of an echo protect tone for a high-speed transmission V.29 modem signal (transmission speed at 9600 or 7200 bps).If errors occur frequently at time of transmission because of the condition of the line, select 'transmit' so that a non-modulation carrier will be transmitted as a pre-image transmission sync signal for about 200 msec.

5.2.3.3 Detailed Discussions of Bits 4, 5, and 60025-3094

Use it to select an appropriate transmission mode: international transmission (1), international transmission (2), or international transmission (3).Use the service soft switch or the dial registration function to select the appropriate transmission mode if errors occur frequently at time of transmission to overseas.

Using the Dial Recognition Function (user level):Select 'international transmission (1)' when making an entry in the Address Book. If errors still occur, select 'international transmission (2)' and then 'internationaltransmission (3)' in sequence until errors stop. The transmission mode selected using the One-Touch Dial function or the Speed Dial function will be give priorityover the setting made by the service soft switch.An international transmission mode may be selected using the keypad if a mode has been selected using this switch; for settings, see the following table:

T-5-3

International transmission (1): select it to ignore the first DIS signal from the other party.International transmission (2): select it to transmit a 1850-Hz total signal when transmitting the DIS signal.International transmission (3): select it to transmit a 1650-Hz total signal when transmitting the DIS signal.


Use it to enable/disable transmission of a 1080-Hz tonal signal before transmission of the CED signal.Select 'transmit' if errors occur frequently because of an echo when reception is from overseas.

Bit Function 1 0

0 not used - -

1 echo protect tone at high-speed transmission transmit do not transmit

2 not used - -

3 not used - -

4 transmission mode: international transmission (1) use do not use

5 transmission mode: international transmission (2) or (3) use do not use

6 transmission mode international transmission (3)

international transmission (2)

7 tonal signal before CED signal transmission transmit do not transmit

MEMO: Any of the following error codes may be indicated because of the line condition at time of transmission##100, ##104, ##281, ##283, ##750, ##755, ##760, ##765

MEMO: Any of the following error codes may be indicated because of an echo at time of transmission##005, ##100, ##101, ##102, ##104, ##201, ##280, ##281, ##283, ##284, ##750, ##760, ##765, ##774, ##779, ##784, ##794

Transmission mode Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0

International transmission (1) * 0 0 1 0 0 * 0



Chapter 5

5-4

5.2.4 SSSW-SW04


Use it to select the number of last flag sequences for a protocol signal (transmission speed at 300 bps). Select '2' if the other party fails to receive the protocol signalproperly.


Use it to select an appropriate reception mode after transmission of the CFR signal.If errors occur frequently at time of reception because of the condition of the line, select 'high speed' for reception mode and, at the same time, selects 'do not receive'for 'ECM reception.'


Use it to select the time length during which low-speed signals are ignored after transmission of the CFR signal.If the condition of the line is not good and, therefore, the reception of image signals is difficult, select '1500 ms.'

5.2.5 SSSW-SW05


T-5-4


Use it to enable/disable millimeter/inch conversion in sub scanning direction for images read in text mode.


Use it to enable/disable millimeter/inch conversion in sub scanning direction for images read in text/photo mode while bit 1 is set to '1'.


Use it to enable/disable transmission of bit 33 and thereafter (DIS signal).


Use it to enable/disable declaration of the use of cut sheets (DIS signal).For reception of an extra-long original, select 'A4/B4 size' if division is to be by the other party.

MEMO: Any of the following error code may be indicated because of an echo at time of reception##005, ##101, ##106, ##107, ##114, ##200, ##201, ##790

MEMO: Any of the following error codes may be indicated at time of transmission##100, ##280, ##281, ##750, ##753, ##754, ##755, ##758, ##759, ##760, ##763 ##764, ##765, ##768, ##769,##770, ##773, ##775, ##778, ##780, ##783, ##785, ##788

MEMO: Any of the following error codes may be indicated at time of reception because of line condition##107, ##114, ##201

Be sure to change bit 4 before changing this bit; if errors still occur, change this bit.When 'high speed' is selected, only high-speed signals (images) will be received after transmission of the CFR signal.

Bit Function 1 0

0 not used - -

1 Conversion from mm to inch (text mode) convert do not convert

2 Conversion from mm to inch (text/photo mode) convert do not convert

3 end DIS signal bits 33 and over prohibit do not prohibit

4 Recording paper length availability declared in DIS signal A4/B4 size any size

5 not used - -

6 not used - -

7 not used - -

If 'prohibit' is selected, the Super Fine reception function or Memory Box function cannot be used for communications from non-Canon machines.

MEMO:Some machines are not designed to divide extra-long originals.

Chapter 5

5-5

5.2.6 SSSW-SW12


T-5-5

The machine will stop the ongoing communication if the transmission/reception of a single original page takes 32 min or more. To use the timer for a purpose otherthan this function, refer to the tables that follow, and select an appropriate time length.When 'do not enable' is selected using bit 7, the time-out length for a single page for all modes will depend on the setting of bit 0 and bit 1.

T-5-6

T-5-7

T-5-8

T-5-9

Bit Function 1 0

0 Time-out period for one page upon transmission 1 0

1 Time-out period for one page upon transmission 1 0

2 Time-out period for one page upon (HT transmission) 1 0

3 Time-out period for one page upon (HT transmission) 1 0

4 Time-out period for one page upon reception 1 0

5 Time-out period for one page upon reception 1 0

6 not used - -

7 Respective page timer settings for transmission and for reception enable do not enable

Time-Out Length for Transmission/Reception Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0

8 min 0 * * * * * 0 0

16 min 0 * * * * * 0 1

32 min 0 * * * * * 1 0

64 min 0 * * * * * 1 1

Time-Out Length for Transmission (in text mode) Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0

8 min 1 * * * * * 0 0

16 min 1 * * * * * 0 1

32 min 1 * * * * * 1 0

64 min 1 * * * * * 1 1

Time-Out Length for Transmission (image mode other than text mode)

Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0

8 min 1 * * * 0 0 * *

16 min 1 * * * 0 1 * *

32 min 1 * * * 1 0 * *

64 min 1 * * * 1 1 * *

Time-Out Length for Reception Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0

8 min 1 * 0 0 * * * *

16 min 1 * 0 1 * * * *

32 min 1 * 1 0 * * * *

64 min 1 * 1 1 * * * *

Chapter 5

5-6

5.2.7 SSSW-SW14


T-5-10


Use it to specify whether to convert or not convert an inch-configuration resolution into a millimeter-configuration resolution for image read in G3 transmission:either in sub scanning direction only or in both main and sub scanning directions. The setting is valid only when bit 1 of SW05 of #1 SSSW is set to '1'.


Use it to specify whether to declare or not declare an inch-configuration resolution to the other machine for G3 communication: if 'declare' is selected, the machinewill indicate that it reads and records at an inch-configuration resolution using the DIS, DCS, or DTC signal.

5.2.8 SSSW-SW23


T-5-11


When logging in Meap, the login name is automatically registered as the 99th addresser name. This SW is for setting whether this 99th name is set as the defaultor not.The default setting is "No". If you change this SW to "Yes", the login name becomes the default of the addresser name, and it is recorded at the facsimile headerand transmitted to the device on the receiving side.

5.2.9 SSSW-SW25


T-5-12


Use it to select the transmission telephone number indicated on the report at the end of transmission.caller's number: indicates the telephone number of the caller on the report.number of other party: indicates the telephone number (CSI signal data) sent from the other part on the report.

Bit Function 1 0

0 not used - -

1 not used - -

2 direction of scanning for inch/mm conversion both main and sub scanning directions

sub scanning direction only

3 not used - -

4 inch-configuration resolution declaration declare do not declare

5 not used - -

6 not used - -

7 not used - -

Bit Function 1 0

0 not used - -

1 not used - -

2 not used - -

3 not used - -

4 not used - -

5 not used - -

6 not used - -

7 Set the login name as the default of the addresser name enable do not(dafault)

Bit Function 1 0

0 transmission telephone number indicated report other party's caller's

1 not used - -

2 not used - -

3 not used - -

4 not used - -

5 not used - -

6 not used - -

7 not used - -

Chapter 5

5-7

5.2.10 SSSW-SW26


T-5-13


T-5-14


Use it to enable/disable indication of a confirmation message before broadcasting in consideration of a mistake during input of addresses.


Use it to enable/disable generation of an error report in response to a press on the Stop key to suspend transmission.

5.2.11 SSSW-SW28


T-5-15


Select whether to use the V.8 protocol when calling. If NO is selected, the V.8 protocol is inhibited at calling and the V.21 protocol is used.


Select whether to use the V.8 protocol when called. If NO is selected, the V8 protocol is inhibited when called and the V.21 protocol is used.


Select whether to execute the V.8 procedure in case that the ANSam signal from the reception side is not recognized when originating a call and the existence ofthe V.8 procedure is informed with the DIS signal from the reception side.Yes: Transmit the CI signal in a response to the DIS signal of the originating side, and execute the V.8 procedure.No: Without transmitting the CI signal in a response to the DIS signal from the reception side, execute the V.21 procedure.In case of the manual transmission, the V.8 late start is not executed regardless of this setting.


Select whether to inform the existence of the V.8 procedure with the DIS signal that is transmitted after the ANSam signal in case that the ANSam signal at thereception is not recognized at the originating side.

Bit Function 1 0

0 not used - -

1 not used - -

2 confirmation screen for broadcasting do not diaplay

3 not used - -

4 not used - -

5 not used - -

6 not used - -

7 error report at time of transmission suspension do not generate generate

Bit Function 1 0

0 not used - -

1 not used - -

2 Not used - -

3 not used - -

4 not used - -

5 not used - -

6 not used - -

7 error report at time of transmission suspension do not generate generate

Bit Function 1 0

0 Caller V.8 protocol NO YES

1 Called party V.8 protocol NO YES

2 Caller V.8 protocol late start NO YES

3 Called party V.8 protocol late start NO YES

4 V.34 reception fallback Prohibited Not prohibited

5 V.34 transmission fallback Prohibited Not prohibited

6 not used - -

7 not used - -

Chapter 5

5-8

Yes: Inform the existence of the V.8 procedure with the DIS signal, and execute the V.8 procedure after transmitting the CI signal by the originating side.No: Without informing the existence of the V.8 procedure, execute the V.21 procedure.In case of the manual transmission, the V.8 late start is not executed regardless of this setting.


Select whether the receiver falls back during V.34 reception. If 'Prohibit' is selected, the receiver does not fall back.


Select whether the transmitter falls beck during V.34 transmission. If 'Prohibit' is selected, teh transmitter does not fall back.

Chapter 5

5-9

5.2.12 SSSW-SW30


T-5-16


Switching the detection method when executing the dial tone detection at the time of calling. 1: New detection method (Default) 0: Old detection method


This bit is used for other function. (Non-disclosure function)

Bit Function 1 0

0 not used - -

1 not used - -

2 not used - -

3 not used - -

4 not used - -

5 Dial tone detection method switching New detection method Old detection method

6 Non-disclosure Fixed -

7 not used - -

Be sure to switch the following switches when switching the switch.- In case setting the switch as 1 (new detection method):

/* DIAL TONE01 */ B11000001/* DIAL TONE02 */ 350/* DIAL TONE03 */ 10/* DIAL TONE04 */ 1/* DIAL TONE05 */ 100/* DIAL TONE06 */ 0/* DIAL TONE07 */ 12/* DIAL TONE08 */ 7/* DIAL TONE09 */ 3

- In case setting the switch as 0 (old detection method):

/* DIAL TONE01 */ B11000001/* DIAL TONE02 */ 600/* DIAL TONE03 */ 10/* DIAL TONE04 */ 10/* DIAL TONE05 */ 0/* DIAL TONE06 */ 0/* DIAL TONE07 */ 0/* DIAL TONE08 */ 5/* DIAL TONE09 */ 0

The setting is fixed as '1', and do not change it.

Chapter 5

5-10

5.3 Setting of Menu Switch (MENU)

5.3.1 <005: NL Equalizer>0025-3129

Use it to enable-disable the NL equalizer.If errors occur often during communication because of the condition of the line, enable (ON) the NL equalizer.

5.3.2 <006: Telephone Line Monitor>0025-3130

Use it to the telephone line monitor function:

5.3.3 <007: ATT Transmission Level>0025-3131

Use it to set the transmission level (ATT).Raise the transmission level if errors occur frequently at time of communication because of the condition of the line. (It means close to 8)

5.3.4 <008: V.34 Modulation Speed Upper Limit>0025-3132

Use it to set an upper limit to the modulation speed (baud rate) for the V.34 primary channel.When '4 (2743 baud)' is selected, the actual communication is executed with 2400 baud.

5.3.5 <009: V.34 Data Speed Upper Limit>0025-3133

Use to set an upper limit to the data transmission speed for the V.34 primary channel between 2.4K and 33.6K bps in increments of 2400 bps. (0: 2.4K to 13: 33.6Kbps).

5.4 Setting of Numeric Parameter (NUMERIC Param.)

5.4.1 <002: RTN transmission condition (1)><003: RTN transmission condition (2)><004: RTN transmission condition (3)>0025-3136

Use it to set RTN signal transmission conditions. Raise these parameters for more lenient conditions if errors occur frequently at time of reception because of trans-mission of the RTN signal.

5.4.2 <005: NCC pause length (pre-ID code)>0025-3137

Use it to set the length of the pause automatically entered between access code and ID code when the NCC (New Common Carrier) line is used for dialing.

5.4.3 <006: NCC pause length (post-ID code)>0025-3138

Use it to set the length of the pause automatically entered between ID code and telephone number of the other party when the NCC (New Common Carrier) line isused for dialing.

5.4.4 <007: pre-pause length at time of ring>0025-3139

Use it to set the length of the pause used when placing a call.

5.4.5 <009: number of comparison digits of source telephone number and target telephone number>0025-3140

Use it to set the number of TSI comparison characters (lower $ characters) for a check on telephone numbers.

MEMO:Any of the following error codes may be indicated at time of transmission because of the line condition##100, ##101, ##102, ##104, ##201, ##281, ##282, ##283, ##750, ##755, ##765, ##774, ##779, ##784, ##789

Any of the following error codes may be indicated at time of transmission because of the line condition##103, ##107, ##114, ##201, ##790, ##793

0(DIAL): generate the monitor sound of the telephone line using the speaker from the start of transmission to DIS.

1: generate the monitor sound of the telephone line using the speaker from the start of communication to the end of it.

2: not used

3(OFF): do not generate the monitor sound of the telephone line usng the speaker.

MEMO:Any of the following error codes may be indicated at time of transmission because of the line condition##100, ##101, ##102, ##104, ##201, ##280, ##281, ##282, ##283, ##284, ##750, ##752, ##754, ##755, ##757, ##759, ##760, ##762, ##764, ##765, ##767, ##769, ##770, ##772, ##774, ##775, ##777, ##779, ##780, ##782, ##784, ##785, ##787, ##789

Any of the following error codes may be indicated at time of reception because of the line condition##103, ##106, ##107, ##201, ##793

MEMO:Any of the following error codes may be indicated at time of reception because of RTN signal transmission##104, ##107, ##114, ##201

RTN signal transmission condition (1) affects the ratio of error lines to the total number of lines per single page of received images.RTN signal transmission condition (2) affects the standard value (*2) of burst errors (*1).RTN signal condition (3) affects the number of errors not reaching the standard value of burst errors.*1: transmission error occurring cover several lines.*2: for instance, if '15' is set, a single burst error will represent an error occurring continuously cover 15 lines.

If any of these lines is detected while an image signal is being received, the RTN signal will be transmitted after receiving the protocol signal of the transmitting party. Higher parameters restrict the transmission of the RTN signal.

Chapter 5

5-11

5.4.6 <010: line connection identification length>0025-3141

Use it to set the time for identifying the line connection.Raise this parameter if errors occur frequently at time of communication because of the condition of the line.

5.4.7 <011: T.30 T1 timer (for reception)>0025-3142

Set the T1 timer at the time of reception (the waiting time till receiving the significant signal after the DIS transmission).

5.4.8 <013: T.30 EOL timer>0025-3143

Set it so that the 1-line transmission time is longer for reception to prevent reception errors caused by a long data length per line (e.g., computer FAX).

5.4.9 <027: V.21 low-speed flag preamble identification length>0025-3150

Use it to detect the time of detection after which command analysis is started after detecting V.21 low-speed command preambles continuously for a specific periodof time.

MEMO: Any of the following error codes may be indicated because of the condition of the line##005, ##018

The line condition identification time is between when the dial signal is transmitted and when the line condition is cut for the transmitting party, while it is between when the DIS signal is transmitted and when the line is cut for the receiving party.

Chapter 5

5-12

5.5 Setting of Printer Functions (PRINTER)

5.5.1 Setting of Bit Switch (SSSW)

5.5.1.1 SSSW-SW05

5.5.1.1.1 Functional Construction0025-3151

T-5-17

5.5.1.1.2 Detailed Discussions of Bits 0 and 10025-3152

Use it to enable/disable placement of priority on LTR paper when an image that may be printed at 100% or in even division on A4, LTR, or LGL is received.The setting of bit 0 and bit 1 affects the order of priority as follows:

T-5-18

However, when priority is on recording in sub scanning direction, the order will be as follows even when bit 1 and bit 0 are set to '0': LTR -> A4 -> LGL.

5.5.1.1.3 Detailed Discussions of Bit 70025-3153

Use it to enable/disable placement of priority on recording in sub scanning direction.

*: Image B4 or shorter and that cannot be printed by division and on A4 recording paper.

5.5.1.2 SSSW-SW06

5.5.1.2.1 Functional Construction0025-3154

T-5-19

5.5.1.2.2 Detailed Discussions of Bit 50025-3155

Set whether to execute the reduction print that forcibly reduces the A4 size document into the B5 size. This function is invalid when outputting the report.

Bit Function 1 0

0 priority on LTR place do not place

1 priority on LGL place do not place

2 not used - -

3 not used - -

4 not used - -

5 not used - -

6 not used - -

7 priority on recording in sub scanning direction place do not place

Bit1 Bit0 Priority of recording paper

0 0 A4 -> LTR -> LGL

0 1 LTR -> A4 -> LGL

1 0 LGL -> LTR -> A4

1 1 LTR -> LGL -> A4

place: if B4 recording paper and A4 recording paper are set and an A4 extra-long image (*) is received, printing will be on the B4 recording paper.

do not place: if B5 horizontal recording paper and A4 recording paper are set and a B4 image is received, printing will be by division and on B5 horizontal recording paper.

Bit Function 1 0

0 not used - -

1 not used - -

2 not used - -

3 not used - -

4 not used - -

5 reduced printing from A4 to B5 enable disable

6 not used - -

7 not used - -

Chapter 5

5-13

5.5.2 Setting of Numeric Parameter (NUMERIC Param.)

5.5.2.1 Numerical Parameter Composition0025-3156

F-5-5T-5-20

5.5.2.2 <001: printing upon reception of extra-length image>0025-3157

Use it to set the range of the image to be removed from when printing an extra-length received image.Lower the parameter to decrease the range if the trailing edge of the received image must be retained (as when it is longer than the effective recording length).

5.5.2.3 <004: leading edge margin>0025-3158

Use it to set the leading-edge margin for the effective recording length.

5.5.2.4 <005: trailing edge margin>0025-3159

Use it to set the trailing-edge margin for the effective recording length.

No. Function Setting range Initial setting Unit

01 Missing areas of printing image when receiving image with longer length than standard 0 to 9999 12 1 mm

04 Leading edge blank area 0 to 9999 3 1 mm

05 Trailing edge blank area 0 to 9999 3 1 mm

<1/4> <READY><NUM>


OK

xxxxx001xxxxx002xxxxx003xxxxx004xxxxx005xxxxx006xxxxx007xxxxx008

Chapter 5

5-14

5.6 Initialization of Set Value (CLEAR)

5.6.1 Overview0025-3160

You can select and initialize data by making the following selections; as a result, settings and various parameter values will be reset to the factory settings.T-5-21

*1: If the model is capable of storing addresses other than fax addresses, the telephone number data will not be deleted upon execution of 'TEL' and 'ALL'. To remove the telephone number data, use the host machine's service mode: COPIER > FUNCTION > CLEAR > ADRS-BK.*2: When 'ALL' is executed, the values suited to the destination of the machine will be stored under 'TYPE'; in the case of Japan, 'standard'.

Item Data to be initialized

TEL telephone number registration data (*1)

USSW SW user data and data registered under Service Mode #1 through #3.of user data, the memory management data will not be deleted.image data collected in memory will not be deleted.

SRV SW user data and data in Service Mode #1 through #3, #7.

NCU data under Service Mode #4.

SRV DATA system dump list data.

REPORT communication control report data.

ALL all settings/registered data (*1) except data under Service Mode #5 TYPE (*2).

COUNTER number of prints, number of sheets read.

ISDN The ISDN related settings of the FAX service mode are initialized.

Chapter 5

5-15

5.7 Test Mode (TEST)

5.7.1 MODEM Test

5.7.1.1 Relay Test (RELAY-1)0025-3162

Use it to see if the individual relays on the NCU board go on and off as expected.

F-5-6

<Using Text Mode>1) From the relays indicated on the screen, select the one you want to test; then, turn it off or on using the Up/Down key. (Some of the relays may not actually exist

on the NCU board.)

5.7.1.2 Frequency Test (FREQ)0025-3163

Of the items indicated below, press one; in response, the DC circuit will be closed and the selected frequency will be transmitted using the tone transmission functionof the modem. You can also monitor the transmission signal by listening to the sound generated by the speaker. To stop the operation and end test mode, press the

key.

F-5-7

'RBT' is not currently supported.

<1/1><MODEM> <READY>


CMLPSHDR

<RELAY-1>

OFF

OFF

OFF

OFF

OFF

OFF

OK

<1/1> <READY>


<FREQ><MODEM>

OK

RBT462Hz1100Hz1300Hz1500Hz1650Hz1850Hz2100Hz

Chapter 5

5-16

5.7.1.3 G3 Signal Transmission Test (G3 Tx)0025-3164

Of the items indicated below, press one. In response, the DC circuit will be closed and the selected frequency will be transmitted using the G3 signal transmissionfunction of the modem. You can also monitor the transmission signal by listening to the sound generated by the speaker. To stop the operation and end test mode,

press the key.

F-5-8

F-5-9

'300-ALL0' through '300-4:1' are not currently supported.

<1/2> <READY>


<G3TX><MODEM>

OK

300bps2400bps4800bps7200bps9600bpsTC7200TC960012000bps

<2/2> <READY>


<G3TX><MODEM>

OK

14400bps300-ALL0300-ALL1300-1:1300-1:4300-4:1

Chapter 5

5-17

5.7.1.4 DTMF Transmission Test0025-3165

Of the items indicated below, press one; in response, the DC circuit will be closed and the selected DTMF signal will be transmitted using the DTMF transmission

function of the modem. You can also monitor the transmission signal by listening to the speaker. To stop the operation and to end test mode, press the key.

F-5-10<Using Text Mode>1) From the items indicated on the screen, select the item you want to test; then, press the key on keypad that corresponds to the DTMF signal to test.

5.7.1.5 V.34 G3 Signal Transmission Test (V34G3Tx)0025-3166

Select the transmission speed you want to test, and then select a modulation speed (baud rate); in response, the V.34 G3 transmission signal will be transmitted to

the telephone line terminal and the speaker. To stop the operation and to end test mode, press the key.

F-5-11<Using Text Mode>1) Select 'SPEED', and then select the speed you want to test using the Up/Down key.2) Select the baud rate you want to test.

'SHORT' is not currently supported.

<1/1> <READY>


<DTMFTX><MODEM>

OK

LONGSHORT

0 1 2 3 4 5 6 7 8 9 * #0 1 2 3 4 5 6 7 8 9 * #

<1/1> <READY>


<V34G3TX><MODEM>

OK

SPEED 33600bps3429baud3200baud3000baud2800baud2743baud2400baud

Chapter 5

5-18

5.7.2 Function Test

5.7.2.1 4800-bps Signal Transmission Test0025-3167

The DC circuit will be closed, and a 4800-bps signal will be transmitted using the 4800-bps signal transmission function of the modem. You can also monitor the

transmission signal by listening to the speaker. To stop the operation and end test mode, press the key.

F-5-12

5.8 Service Report (REPORT)

5.8.1 System Data List0025-3169

Use it to check the settings associated with the service soft switch and service parameters.

<READY><1/1>


<FACULTY> <G34800TX>

OK

G34800TX

Chapter 5

5-19

F-5-13

��

��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

� ��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

Chapter 5

5-20

5.8.2 System Dump List0025-3170

Use it to check the history of communications, both successful and error.

F-5-14*1: RX, total reception number of times; TX, total transmission number of times.*2: number of pages sent/received according to original size.*3: number of pages sent/received in connection with different modem speeds (Standard, Fine, Super Fine, Ultra Fine).*4: number of pages sent/received in connection with different modes.*5: number of pages sent/received in connection with different coding methods.*6: number of transmissions/receptions according to mode.*7: number of occurrences according to error code.

T-5-22

MEMO:A system dump list is generated when you execute the following in service mode: FAX > Report > DUMP.

Indication sample

##280 1 7 3 0 0

##280number of errors



��

��

� ��

��

� � ��

��

��

��

��

��

��

��

� � � ��

! � � � � �� "�� "��

��

###############################

### �$� � �� ###

###############################

��

%��

� � � � � � � �

� � � � � � � �

� � � � � � � �

� � � � � � � �

� � � � � � � �

� � � � � � � �

� � � � � � � �

� � � � � � � �

� � � � � � � �

� � � � � � � �

� � � ��

� � � � � � � �

%��

� � � � � � � �

�

%��

#�

#�

#�

#�

#�

#�

#�

#�

#�

Chapter 5

5-21

It provides error information on the 3 most recent communications.

F-5-15*1: service error code.*2: START TIME, date and time (in 24-hr notation).*3: OTHER PARTY, telephone number sent by the other party.*4: MAKER CODE, manufacturer code.*5: MACHINE CODE, model code.*6: bit 1 through bit 96 of DIS, DCS, or DTC that has been received.*7: bit 1 through bit 96 of DIS, DCS, or DTC that has been transmitted.*8: RX, procedural signal received; TX, procedural signal transmitted.

��

��

��

��

��

��

��

��

� � �� !�� "� �!�� # #$� �� !� � �� %�� &'()� !� � �� &*+ ,#$ ��-� � �#� ��!� ��"� � �� % �!�� %�� %��

� �. � / &01 � 2� � �� / &01 �� 2� / &01 �� 2� � � � / &01 �� 2� . � / &01 � 2� �� / &01 �� 2� / &01 �� 2� � � � / &01 �� 2

�

�. � "�� !��

. � "�� ! � ��3�� 3"�� 3�� 3"�� 3�� 3"��

�. � � � � � � �

. � ��3�� 3"�� 3�� 3�� ! "

��

� � �� !�� "� �!�� # #$� �� !� � �� %�� &'()� !� � �� &*+ ,#$ ��-� � �#� ��!� ��"� � �� % �!�� %�� %��

� �. � / &01 � 2� � �� / &01 �� 2� / &01 �� 2� � � � / &01 �� 2� . � / &01 � 2� �� / &01 �� 2� / &01 �� 2� � � � / &01 �� 2

�. � "�� !��

. � "�� ! � ��3�� 3"�� 3�� 3"�� 3�� 3"��

�. � � � � � � �

. � ��3�� 3"�� 3�� 3�� ! "

�� !��

� � �� !�� "� �!�� # #$� �� !� � �� %�� &'()� !� � �� &*+ ,#$ ��-� � �#� ��!� ��"� � �� % �!�� %�� %��

��

Chapter 5

5-22

5.8.3 Error Transmission Report0025-3171

An error transmission report is an error transmission report together to which a service error code and error dump list is attached.

F-5-16

��

�� ! ��"� �� # � "�� "�� $$��

%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% �� %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%

� � �� ! ��

� �� ! � ��&�� '� �� (�� &�� ) )�� '�� *+,-� �� *./ 0)� ��1� �� )� ��

� �2 ! 3 *45 � 6� � �� 3 *45 �� 6� 3 *45 �� 6� � � � 3 *45 �� 6� �2 ! 3 *45 � 6� � � �� 3 *45 �� 6� 3 *45 �� 6� � � � 3 *45 �� 6

�2 ! ��

�2 ! �� 7�� 7�� 7�� 7�� 7�� 7��

�2 ! ��

�2 ! ��7�� 7�� 7�� 7��

Chapter 6 Error Code

Contents

Contents

6.1 User Error Code............................................................................................................................................................. 6-16.1.1 User Error Code ........................................................................................................................................................................... 6-1

6.2 Service Error Code ........................................................................................................................................................ 6-26.2.1 Service Error Code ....................................................................................................................................................................... 6-2

Chapter 6

6-1

6.1 User Error Code

6.1.1 User Error Code0025-3173

T-6-1

No. T/R Description

#001 [T] an original has jammed.

#003 [T/R] tine-out for copying or sending/receiving a single page has occurred.

#005 [T/R] time-out for initial identification (T0/T1) has occurred.

#008 [R] a mismatch of passwords at time of polling transmission has occurred.

#009 [R] recording paper has jammed or is absent.

#012 [T] recording paper is absent at the other party.

#018 [T/R] auto call initiation has failed.

#022 [T] call initiation has failed.

#037 [R] image memory overflow at time of reception has occurred.

#080 [T] the other party has no F code reception function/or is not set to receive it.

#081 [T] the other party has no password reception function/or is not to receive it.

#099 [T/R] the Stop key is pressed while a communication is under way.

#102 [T/R] a mismatch of F-code/password has occurred.

#995 [T/R] a memory communication reservation has been cancelled.

Chapter 6

6-2

6.2 Service Error Code

6.2.1 Service Error Code0025-3174

T-6-2

No. T/R Description

##100 [T] at time of transmission, the procedural signal has been transmitted more than specified.

##101 [T/R] the modem speed does not match that of the other party.

##102 [T] at time of transmission, fall-back cannot be used.

##103 [R] at time of reception, EOL cannot be detected for 5 sec (15 sec if CBT).

##104 [T] at time of transmission, RTN or PIN is received.

##106 [R] at time of reception, the procedural signal is received for 6 sec while in wait for the signal.

##107 [R] at time of reception, the transmitting party cannot use fall-back.

##109 [T] at time of transmission, a signal other than DIS, DTC, FTT, CFR, or CRP is received, and the procedural signal has been sent more than specified.

##111 [T/R] memory error has occurred.

##114 [R] at time of reception, RTN is transmitted.

##200 [R] at time of reception, no image carrier is detected for 5 sec.

##201 [T/R] DCN is received outside the normal parity procedure.

##204 [T] DTC without transmission data is received.

##220 [T/R] system error (main program out of control) has occurred.

##223 [T/R] while a communication is under way, the line is cut.

##224 [T/R] in G3 communication, an error has occurred in the procedural signal.

##226 [T/R] the stack printer has fallen outside the RAM area.

##229 [R] the recording unit has remained locked for 1 min.

##232 [T] encoding error has occurred.

##237 [R] decoding error has occurred.

##238 [R] the print control unit is out of order.

##261 [T/R] system error has occurred.





##284 [T] at time of transmission, DCN is received after transmission of TCF.

##285 [T] at time of transmission, DCN is received after transmission of EOP.

##286 [T] at time of transmission, DCN is received after transmission of EOM.

##287 [T] at time of transmission DCN is received after transmission of MPS.

##288 [T] after transmission of EOP, a signal other than PIN, PIP, MCF, RTP, or RTN has been received.

##289 [T] after transmission of EOM, a signal other than PIN, PIP, MCF, RTP, or RTN has been received.

##290 [T] after transmission of MPS, a signal other than PIN, PIP, MCF, RTP, or RTN has been received.

##670 [T] at time of V.8 late start, the V.8 ability of DIS front the receiving party is expected to be detected, and the CI signal is expected to be transmitted in response; however, the procedure fails to advance, and the line is released because of T1 time-out.

##671 [R] at time of V.8 arrival, procedure fails to move to phase 2 after detection of CM signal from caller, causing T1 time-out and releasing line.

##672 [T] at time of V.34 transmission, a shift in procedure from phase 2 to phase 3 and thereafter stops, causing the machine to release the line and suffer T1 timeout.

##673 [R] at time of V.34 reception, a shift in procedure from phase 2 to phase 3 and thereafter stops, causing the machine to release the line and suffer T1 timeout.

##674 [T] at time of V.34 transmission, a shift in procedure from phase 3 and phase 4 to the control channel and thereafter stops, causing the machine to release the line and suffer T1 timeout.

##675 [R] at time of V.34 reception, a shift in procedure from phase 3 and phase 4 to the control channel and thereafter stops, causing the machine to release the line and suffer T1 timeout.

##750 [T] at time of ECM transmission, no meaningful signal is received after transmission of PPS-NULL, causing the procedural signal to be transmitted more than specified.

##752 [T] at time of ECM transmission, DCN is received after transmission of PPS-NULL.

##753 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-NULL, or T5 time-out (60 sec) has occurred.

##754 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-NULL.

##755 [T] at time of ECM transmission, no meaningful signal is received after transmission of PPS-MPS, causing the procedural signal to be transmitted more than specified.

##757 [T] at time of ECM transmission, DCN is received after retransmission of PPS-MPS.

##758 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-MPS, or T5 time-out (60 sec) has occurred.

##759 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-MPS.

Chapter 6

6-3

##760 [T] at time of ECM transmission, no meaningful signal is received after transmission of PPS-EOM, causing the procedural signal to be transmitted more than specified.

##762 [T] at time of ECM transmission, DCN is received after transmission of PPS-EOM.

##763 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-MPS, or T5 time-out (60 sec) has occurred.

##764 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-EOM.

##765 [T] at time of ECM transmission, no meaningful signal is received after transmission of PPS-EOP, causing the procedural signal to be transmitted more than specified.

##767 [T] at time of ECM transmission, DCN is received after transmission of PPS-EOP.

##768 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-EOP, or T5 time-out (60 sec) has occurred.

##769 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-EOP.

##770 [T] at time of ECM transmission, no meaningful signal is received after transmission of EOR-NULL, causing the procedural signal to be transmitted more than specified.

##772 [T] at time of ECM transmission, DCN is received after transmission of EOR-NULL.

##773 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of EOR-NULL, or T5 time-out (60 sec) has occurred.

##774 [T] at time of ECM transmission, ERR is received after transmission of EOR-NULL.

##775 [T] at time of ECM transmission, no meaningful signal is received after transmission of EOR-MPS, causing the procedural signal to be transmitted more than specified.

##777 [T] at time of ECM transmission, DCN is received after transmission of EOR-MPS.

##778 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission EOR-MPS, or T5 time-out (60 sec) has occurred.

##779 [T] at time of ECM transmission, ERR is received after transmission of EOR-MPS.

##780 [T] at time of ECM transmission, no meaningful signal is received after transmission of EOR-EOM, causing the procedural signal to be transmitted more than specified.

##782 [T] at time of ECM transmission, DCN is received after transmission of EOR-EOM.

##783 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of EOR-EOM, or T5 time-out (60 sec) has occurred.

##784 [T] at time of ECM transmission, ERR is received after transmission of EOR-EOM.

##785 [T] at time of ECM transmission, no meaningful signal is received after transmission of EOR-EOP, causing the procedural signal to be transmitted more than specified.

##787 [T] at time of ECM transmission, DCN is received after transmission of EOR-EOP.

##788 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of EOR-EOP, or T5 time-out (60 sec) has occurred.

##789 [T] at time of ECM transmission, ERR is received after transmission of EOR-EOP.

##790 [R] at time of ECM reception, ERR is transmitted after transmission of EOR-Q.

##791 [T/R] while ECM mode procedure is under way, a signal other than a meaningful signal is received.

##792 [R] at time of ECM reception, PPS-NULL cannot be detected over partial page processing.

##793 [R] at time of ECM reception, no effective frame is received while high-speed signal reception is under way, thus causing time-out.

##794 [T] at time of ECM reception, PPR with all 0s is received.

##795 [T/R] a fault has occurred in code processing for communication.

##796 [T/R] a fault has occurred in decoding processing after reception of ECM

No. T/R Description

Jun 9 2010

Documents

SERVICE MANUAL - Canon Globaldownloads.canon.com/ir-advance_bw/Super_G3_Fax_Board-AF1_SM_… · This manual has been issued by Canon Inc. fo r qualified persons to learn technical