Indesit Compa© 2008 Reg. Office: Peterborough PE2

Service Information

WASHING MACHINE

Models Comm.Covered Code

LCD DisplayARGD149K EU 61359

5407472 Issue 1 Sept 2008

ny UK Ltd9JB Registered in London: 106725

Indesit Company

SAFETY NOTES & GENERAL SERVICING ADVICE1. This manual is NOT intended as a comprehensive repair/maintenance guide to the appliance.2. It should ONLY be used by suitably qualified persons having technical competence applicable

product knowledge and suitable tools and test equipment.3. Servicing of electrical appliances must be undertaken with the appliance disconnected (unplugged)

from the electrical supply.4. Servicing must be preceded by Earth Continuity, Earth Resistance and Insulation Resistance

checks.5. Personal safety precautions must be taken to protect against accidents caused by sharp edges on

metal and plastic parts.6. After servicing the appliance must be rechecked for Electrical Safety. In the case of appliances

which are connected to a water supply (i.e.: Washing Machines, Dishwashers & Food Centres etc.) checks must be made for leaks from seals gaskets and pipe work and rectification carried out where necessary.

7. It can be dangerous to attempt 'DIY' repairs / maintenance on complex equipment and the Company recommends that any problem with the appliance is referred to its own Service Organisation.

8. Whilst the Company has endeavoured to ensure the accuracy of the data within this publication they cannot hold themselves responsible for any inconvenience or loss occasioned by any error within.

IMPORTANT SAFETY NOTE

Risk of Electric ShockThe metal heatsink fitted on the Power Module may hold an electrical charge for a short period after switching off the machine.Allow 5 minutes after disconnecting the machine from the electrical supply before commencing ANY work.

2 of 22

Service Manual UK English

Indesit Company

SERIAL NUMBER / INDUSTRIAL CODE EXPLANATION

INDEX

Safety & Servicing Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Serial Number Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Controls & Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 8Wash Programmes & Demo Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Controls Information / Main Board Programming. . . . . . . . . . . . . . . . . . . . . . . 10 - 11Automatic Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Wiring Diagram Legend. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Wiring Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Error Codes & Possible Causes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Dismantling Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 - 21

Serial Number Example

3 10 02 0895

Four remaining digits = Build number that day 895th builtThird two digits = Day of manufacture 2nd of monthSecond two digits = Month of manufacture OctoberFirst digit = Year of manufacture 2003

Industrial Code Example

37 24455 0010

Last four digits = 0000 original production.

Second five digits = COMMERCIAL CODE*

First two digits = Factory of origin* Vital for correct model information and system identification

Other numbers denote major production changes

3 of 22

Service Manual UK English

Indesit Company

SPECIFICATIONS

Models Covered ARGD149K EU

Colour K = Black

Dimensions Height 850 mmWidth 595 mm

Depth 600 mm Weight 72 kg Nett Weight Packed 74 kg

Country of Origin Great Britain - Kinmel Park Factory (94)

Electrical Supply 220/240 Volts AC @ 50Hz Fuse 13amp

Energy Class A

Washing Performance Class: A

Drying Performance Class: B

Energy Consumption 1.52 kWh / Cycle @ 60°C Cotton

Water Consumption 69 litres @ 60°C Cotton

Wash Load 8 kg Cottons

Spin Speed 1400 rpm

Drum (Outer) Plastic. Capacity = 58 litres

Control PCB 220/240Volt 50/60Hz Type Merloni EVO 2

Water Supply Cold Valve - Coil Resistance 3.8 KΩCold Fill only Max Pressure = 1 Mpa (10bar / 145 PSI)

Minimum Pressure = 0.05 Mpa (0.5bar / 7.25 PSI)

Wash Heater 1700 Watts @ 230 voltsResistance 30Ω

Thermistor NTC Resistance: 20KΩ @ 20°C

Pump 2 Pole Synchronous220 / 240 Volt 25 Watt, Resistance = 165 Ω

Wash Motor CESET 3 Phase Induction (stator 50)195v - 3A - 800W - 310Hz - 17500rpm.

Door Lock P.T.C. solenoid with emergency door release

Torque Settings Upper Balance Weight = 24 NmLower Balance Weight = 24 Nm

NOTE: - The module fitted in production has a fixed (welded) EEProm and can only be programmed with a Smart Card / Palm (Hand Held Device).

Programme (1st press of thebutton); temperature 60°C;using a load of 8 kg} Energy rated programmes

according to regulationEN 60456

4 of 22

Service Manual UK English

Indesit Company

CONTROLS

FIRST TIME USEThe first time the machine is switched on, you will be asked to select the language - the display will automatically show the language selection menu. To select the desired language, press the Temperature and Spin buttons to scroll through the choices. To confirm the selection press the Child Lock button. To select a different language option, press and hold the Child lock button + Temperature button + Spin button simultaneously for 5 seconds to enter the language selection menu.(The machine must be switched on to do this.)

ON-OFF / SELECTING A PROGRAMMEThe machine is switched on by pressing the ON-OFF button.The display lights up.Load the laundry and detergent.Select the desired programme by pressing the correct programme button. Select the option required.The display will show the programme selected, spin speed, temperature and time.Press the Start / Cancel button.A beep will be heard followed by a CLUNK from the door lock solenoid as it locks the door, at this stage the door locked indicator symbol will light.

TO STOP OR CHANGE A PROGRAMMEPress the ON-OFF button for approximately 3 secondsSelect PUMP OUT on the programme dial.Switch on and re-start.When the machine has finished emptying, press the ON-OFF button.Select a new programme and re-start.NOTE: If you cancel a HOT wash programme, take care when removing the laundry, it may still be VERY HOT.

continued ...

5 of 22

Service Manual UK English

Indesit Company

DOOR LOCKED INDICATOR LIGHTThe Door Locked indicator light will come on when you press the START / PAUSE button and will stay lit throughout the programme.When the programme has finished, the indicator light will go out and you can then open the door.A double CLUNK noise will be heard from the door lock solenoid at this point.If the door is not closed properly prior to starting as programme, the door lock solenoid will 'CLUNK' approximately 5 times followed by a flashing DOOr indication in the display window. Every 5 seconds from then onwards there will be an audible beep.Push the door closed and press START / PAUSE button to commence the cycle.N.B. If the Delay Start function has been activated, the door cannot be opened; Pause it by pressing the Start/Pause button if you wish to open the door.

CHILD LOCKTo set the Child Lock, start the programme required then press and hold the Child Lock button for2 seconds. At this point a red LED will illuminate on the button - Child Lock function is now active.

To Remove Child Lock - Press and hold the Child Lock button down for 2 seconds.NOTE: - The Child Lock option will need to be removed before another programme can be selected.

MEMORYTo store a customised programme with different preferences, press and hold the Memory (M) button to store the programme. To recall the stored cycle, press the memory button.

6 of 22

Service Manual UK English

Indesit Company

e .

e

e

OPTIONS

Options are selected by pressing the button and confirmed by illumination an orange LED sited in the button.If an option is not available with a programme, the LED will flash and a bleeping noise will be heard when pressing the button.

MINI LOAD This option is recommended if the Wash Load is equal to or less than half of the maximum recommended load. In addition to reducing the actual wash time, this option will reducthe water and energy consumption by 50%. It cannot be used with & Pump Out options

EASY IRON By selecting this option the wash and spin cycles will be modified in order to reduccreases. At the end of the cycle, the drum will turn periodically and the Start/Pause and ReduceCreases lights will flash Orange & End of Cycle will appear in the display. To complete the programme, press Start/Pause or Easy Iron button. If it is used with Silk/Curtains Cycle the machine suspends the wash load in water with Start /Pause and Easy Iron lights flashing Orangand Rinse Hold will appear in the display. To complete the programme (pump out water) press Start/Pause or Easy Iron buttons. It cannot be used with & Pump Out options.

CHILD LOCK When activated programme and functions cannot be altered. (Control panel lock)

EXTRA RINSE By selecting this option, the efficiency of the Rinse is increased and optimal detergent removal is guaranteed. Ideal for large wash loads and items for young children or people with sensitive skin. It cannot be used with & Pump Out options.

DELAY START Press this button repeatedly until the desired delay period has been reached. This can be set from 1 to 24 hours.

SPIN REDUCTION Pressing this button can reduce or completely exclude the Spin Cycle. The Spin Speed set will be indicated in the display.

TEMPERATURE Pressing this button will decrease the programme temperature pre-set by the programme selection and will be indicated in the display.

PREWASH If this function is selected, the pre-wash cycle will run; this is useful for removing stubborn stains. N.B.: put the detergent in the relevant compartment. It cannot be used with & Pump Out options.

Option Buttons

�� �

�� �� �� �

�� �

��� �� �� �� ��

7 of 22

Service Manual UK English

Indesit Company

STAIN REMOVAL This function is particularly useful for the removal of stubborn stains. Place extra compartment 4 (supplied) into compartment 1. When pouring in the bleach, be careful not to exceed the “max” level marked on the central pivot (see figure). To run the bleach cycle on its own, pour the bleach into extra compartment 4, set the “Rinse” programme and activate the “Stain removal” programme. To bleach during a wash cycle, pour in the detergent and any fabric softener you wish to use, set the desired wash cycle and enable the “Stain removal” function. N.B. The use of extra compartment 4 excludes the “Pre-wash” function. It cannot be used with & Pump Out options.

�

�� �� �

MAX

12

4

3

8 of 22

Service Manual UK English

Indesit Company

WASH PROGRAMMES

DEMO MODE

LANGUAGE SELECTION

To change the language on the appliance, press and hold the following 3 buttons for approximately 5 seconds:CHILD LOCK (Control Panel Lock)SPIN REDUCTION BUTTONTEMPERATURE SELECTIONThen select the language required using the TEMPERATURE or SPIN buttons. Confirm the selection by pressing the CHILD LOCK (Control Panel Lock) button.

To Activate Demo ModePress and hold the following 3 buttons simultaneously for approximately 20 seconds.

ON / OFF BUTTONOPTION BUTTON NEAREST TO

START/PAUSE BUTTON START / PAUSE

Demo ON will flash periodically in the display.

To De-Select Demo ModePress and hold the following 2 buttons simultaneously for approximately 3 seconds:

ON / OFF BUTTONSTART / PAUSE

Demo OFF will appear in the display. Note:- At this point the user will need to select the language required. There are approximately 22 languages available.

������������ ������

��������������� �������� ��������������� ������������������������������������������� !"

#������� ���������������

$�%"���"

& !'

$�%"

�(

&���'

#��� �

$�%"

���(

&)�'

$�%"

���(

&)�' !���

(������ *�+

���,���� -��

��.���

��� �������

$� �/��(

���������������������������

!���� �&�'�� ��������� �� ����� ���� ���*�� %!����% ������� +,- ./,, � � � � 0 /

!���� ����������������������������(�%!����% ��������� ������������%����� 1,- ./,, � � � � 0 /

!���� ���������������������������(�%!����% ��������� � %�������%����� /,- ./,, � � � � 0 /

0� ������� �������������������������(�%!����% ������������%����� 1,- 0,, � � � � 2�3 .�3

0� �������������������������������%�4��%!����% ������������%����� /,- 0,, � � � � 2�3 .�3

$�%�1�2�� ��������� �� ����� ���� �������$����%�4��%!����% �4�� ����5���6%!7���������%�$������%����%6��� ��%������������5����������4�!���� 8�

2,- 0,, � � � � 2 �

$�%�3�2����������������������� ��������$����%�4��%!����% �4�� ����5���6%!�7��������%�$������%����%6��� ��%������������5����������4�!���� 8�

2,- 0,, � � � � .�3 �

����������������������

,�.����������(�%!����% � %�������%����� /,- 0,, � � � � 9 .

$�������%%����$�����!�������!�%��������� �

0��)4!����� ��$���4�� ���������%6��� �(�������%��4��� 2,- , � � � � 9 .

-�����$������%������ ������ /,- 1,, � � � � 9 .

������������������

:�����#��� � ��������� �� ����� ���� � � ./,, � � � � 0 �

�%����#��� ����������� �� ����� ���� � � 0,, � � � � 2�3 �

������������� � ��������� �� ����� ���� � � ./,, � � � � 0 /

�� #����� ����������� �� ����� ���� � � , � � � � 0 �

��� ���������$����������!�%����������6

������ ��#%�!�

-�������

�

9 of 22

Service Manual UK English

Indesit Company

CONTROLS INFORMATIONA single control board located at the back of the machine contains all the circuitry to control the machine and interfaces with the LCD / Selector, option buttons and LEDs located on the console panel. The control board has an access port to the rear of the machine.Programmes are selected by using the Selector Dial. Special options can be selected by pressing the appropriate buttons and the programme process followed by LEDs.The machine is switched on using the On/Off button and selected programmes started by pressing the Start/Cancel button.

MAIN BOARD PROGRAMMING

Programming a Main BoardThere are a number of ways the board can be programmed - some of which are not applicable to certain markets.

Types of programming:1. Handheld Terminal (Palm).2. Emit / Memwriter (UK Indesit Service Engineers).3. Smart Reader & Smart Card see photo.

Smart Card Reader

Smart Cardthis card hold the program fileand can only be used ONCE.

10 of 22

Service Manual UK English

Indesit Company

PROGRAMMING (Using Smartcard Reader / Card)

If the Main Module has been replaced during a repair the board will require programming using the following method.1. Do NOT connect the machine to electrical supply.2. Insert the pre-programmed card into the Card

reader. Care must be taken at this point to ensure the card is inserted correctly with the Chip on the card facing the PCB of the Reader.

3. Insert the Reader & Card into module connection port - see photo.

4. Connect the machine to the Electrical supply, the LED's on the Smart Card Reader will light in this sequence:

a) Red OFF: Good Communication between Smart Card Reader & Card.

b) Red OFF; Green Blinking: Download taking place.c) At end, Green ON ---> Download OK.d) At end, Red ON ---> Download NOT OK.5. Programming Complete, disconnect the machine

from Electrical supply.6. Remove the Smart Card Reader.

Smart Card Reader and Smart Card in use

11 of 22

Service Manual UK English

Indesit Company

Automatic Features

Auto Half LoadAuto half load adjusts the amount of water in the wash load depending on the absorbency of garments in the wash load.

Fabric Conditioner DispensingDispensing of fabric conditioner is achieved by energising both the Pre-Wash and Main Wash cold valves.

Out of Balance ProtectionThe machine has an inbuilt feature to prevent spinning with an unbalanced load. A calculation via the motor tacho and control board detects the current drawn by the motor during distribution.Before each spin, the controls senses the load within the drum and if the load is calculated to be out of balance the machine will not automatically spin to the full speed.There are two levels of out of balance, level 1 @ 480 grammes and level 2 @ 1030 grammes.If the out of balance is below level 1 the machine will spin at full speed, if between level 1 and level 2 the machine will spin at the reduced speed of 600 rpm and above level 2 spin at reduced speed of 400 rpm. There are 15 attempts at level 1 with 57 attempts in total, this being the same for both cotton and synthetic spins.The wool spin has one level of out of balance @ 1.8 kg. The controls will make three attempts to achieve a balance, if after three attempts a balance is not achieved; the spin is reduced to a speed of 90 rpm.

WIRING DIAGRAM LEGEND

EV Solenoid valve N Neutral or Terminal board

EVA Drying solenoid valve PS Drain pump

EVC Hot water solenoid valve R Heating element

EVF Cold water solenoid valve RR Heating element

EVL Wash solenoid valve TG Main earth

EVP Prewash solenoid valve N Neutral or Terminal board

IP Door switch

L Line or Lamp

MR Microdelay device

12 of 22

Service Manual UK English

Indesit Com

pany

13 of 22

Ser WIRING DIAGRAM

1

5Test

j9

1A

T6745

3

EMI

Wash MotorThermalProtector(if fitted)

10A

3 phaseWash Motor

Motor Frame 100 Kohms

to Earth via Input Filter

Black

Pump

Tacho

1234568 9 7

j11

12345

12345112

2j14

j13

1

2

j12

VNR

1 2 3 4 5

LCDDISPLAY

Module

j15

GN

DSC

LSD

AVc

c

12345.

j7

SDA

SCL

GND

Vcc

vice Manual U

KEnglish

5407472wdiag.pdf

5432121

21

1

OVE

RFLO

W

EVL

EVP

P

NL

12

1

14

11 16

RR

TF

R

1 4

3

1

2

1

2

12

2 3 4

1234

C

34679

1

EMPT

Y

FULL

COM

MO

N

GN

D

RX

SEN

.CO

ND TG

1 2R

R56

D

4

2

3

4 3 2

j5 j1 j3 j8

j10j2j4

12A

12A

10A

10A 8

A

10A

10A

1A

10w

10w

1 2

RTN_IPRTN_PORTA

WashThermistor

Fabric Cold

DoorInterlock

Lav.

Mains InputFilter

PressureSwitch

Water Valves

1

2

*1 2

1112

j15NC

Indesit Company

ERROR CODES & POSSIBLE CAUSESWhen an error occurs the following will be indicated in the display.

Refer to the chart below for the error code definitions.

LCDDisplayCode

Possible Causes & Actions

F01 Motor triac short circuit: Check motor and module connectionsF02 Motor jammed / tacho detached: Check motor and module connectionsF03 NTC short/open circuit: Check thermistor and module connectionsF04 Pressure switch jammed on empty: Check switch and moduleF05 Pressure switch jammed on full or pump blocked: Check pump and switchF06 N/AF07 Heater relay stuck: Check heater and module connectionsF08 Heater relay stuck: Check pressure switch, heater and module connectionsF09 Setup error: Check EepromF10 Pressure switch not sensing: Check switch and module connectionsF11 Pump cannot be activated: Check pump, connections and wiringF12 No communication between cards: Check module connections

F13High temperature Rise In Drying: Reduced air flow through dryer heater assembly.Check operation of fan motor and dryer filter for blockage

F14 No Heat In Drying: Check one shot thermostat. Check heater, valve and fan motor module connections. Edge connector J10

F15 No Drying: Possibly dryer relay open circuitF16 N/AF17 Door lock error: Check door, door lock and module connectionsF18 Communication error (3 phase motor): Replace power board

14 of 22

Service Manual UK English

Indesit Company

DISMANTLING INSTRUCTIONSSAFETY NOTES1. Ensure that the appliance is disconnected from the electrical supply before dismantling.2. Beware of sharp edges on metal panels, plastic mouldings, and pressed parts.3. Some fixings (especially those into plastic) must be tightened to the correct specification using a

suitable torque wrench.4. Insulation resistance tests must be carried out with the pressure switch set to ensure that the water

heater is 'in-circuit' during the test.These appliances are manufactured with a '3 phase' motor and uses a different type of power module. This power board is fitted with a large aluminium heat sink which remains live after the power is disconnected.Under no circumstances should the board be removed under the time shown below.Alternative 'quick methods' of discharging the board SHOULD NOT be used or attempted.!

A Table Top1. Remove the two screws at the top rear of cabinet.2. Slide the table top backwards to disengage the location fixings at the rear and lift off.

B Lower Rear Access Panel1. Remove three screws from the lower rear access panel.2. Pull the top edge of the panel out and disengage it from its location fixings along the bottom.

C Dispenser Drawer1. Open the dispenser drawer fully. Holding the dispenser firmly, lift the right hand side and slide

towards you.2. Remove the drawer pivot pin and remove the drawer front.

D Console Panel1. Remove the table top (A).2. Remove the dispenser drawer (C).3. Remove two top screws securing the panel to the cabinet and two screws securing the panel to the

dispenser.4. Unplug the wiring from the cabinet side to the console PCB - taking note of position.5. Remove two screws from the valve support plate and move the dispenser to the rear.6. Unclip two plastic lugs securing the console panel to the front panel and lift clear.7. Avoid unclipping and handling the control board unless absolutely necessary, as the control board

is susceptible to static electricity.

IMPORTANT NOTERisk of Electric ShockThe metal heatsink fitted on the Power Module may hold an electrical charge for a short period after switching off the machine.Allow 5 minutes after disconnecting the machine from the electrical supply before commencing ANY work.

15 of 22

Service Manual UK English

Indesit Company

E Console PCB & Button Assemblies1. Remove the console panel (D).2. Remove wiring plug - taking note of position.3. Remove three securing clips and lift away from the console.

F Pressure Switch1. Remove the table top (A).2. Disconnect the wiring connection block and pressure hose.3. Carefully unclip bracket from cabinet side and then unclip switch from bracket.

G Door Seal & Restraint:1. Door Seal to Front Panel Fixing

The door seal is fixed to the cabinet front panel by a wire clamp and a small spring. The spring is normally at the bottom of the door.Carefully place a small screwdriver into one of the lugs of the spring and by stretching the spring the wire band can be removed.

2. Drum FixingThe door seal is fixed to the drum with a zipper retainer. After removing the front panel (J) remove the zipper retainer. On refitting place the zipper retainer around the door seal and tighten. Observe correct seal and zipper fixing positions.

H Door Interlock

1. Remove the door seal restraint (G).2. Peel the door seal off the front panel, and fold it back into the inner drum.3. Remove 2 screws from the interlock.4. The interlock can now be eased out, allowing access to the wiring connection block and emergency

release strap.5. Care must be taken to ensure the correct orientation of the wiring connection plug to prevent

seriously damaging the interlock and / or control board.

16 of 22

Service Manual UK English

Indesit Company

e

e

J Front Panel1. Remove the table top (A), dispenser drawer (C) and console panel (D).2. Remove the door seal restraint (G) and door interlock (H).3. Grip the appliance kickstrip at both ends tilt forwards, and pull it off in a forward direction.4. Remove 4 front panel fixing screws (2 bottom and 2 top).5. Slide the dispenser housing backwards so that it clears the console backplate opening.6. Lift the front panel upwards to disengage the four cabinet fixing pegs, and lift off.

K Door Seal1. Remove the table top (A), dispenser drawer (C) and console panel (D).2. Remove the door seal restraint (G), door interlock (H) and front panel (j).3. Remove the drum door seal restraint (G) and lift clear.

L Drive Belt1. Remove the table top (A).2. Remove the lower rear access panel (B).3. Carefully peel the belt off the motor pulley taking care not to trap fingers and using suitable

protection against sharp edges.4. To refit the belt, place it round the motor pulley first, tie-wrap the belt onto the drum pulley, and

rotate the drum from the door aperture to move the belt into position.5. Ensure any remaining tie-wraps are removed.

It is essential for continued safety that only a genuine spare is fitted. The belt is electrically conductive and provides an electrical earth to prevent static built up on the inner drum assembly.

I Door Assembly1. Open the door through 180° and remove four

screws securing the hinges to the front panel. Ease the hinges from the panel.

2. The door trims can now be split. Lay the door assembly face down on a suitably protected surface and remove 6 screws securing the two halves of the door.

3. Unclip the two halves at the hinge end and separate a sufficient distance to slide out the door glass.

4. When removing the hinges, note the orientation. To remove, fold hinges inward, slide towards each other to release other end. See photo.Reassemble in reverse order.

5. To fully separate the halves, slide the front away from the handle.

6. To remove the handle or latch, slide securing pin out noting the position of the spring and latch.

Top Hinge removal (shown below) - Slide towards lower hinge, twist to the left and slidup to release.Lower Hinge removal - Slide upwards, twist to thright and slide down to release.

17 of 22

Service Manual UK English

Indesit Company

M Motor1. Remove the lower rear access panel (B) and drive belt (L).2. Disconnect the motor wiring connection plug and earth wire.3. Using a 13 mm socket or ratchet ring spanner, remove both motor mount fixing screws.4. Ease the motor off the drum mountings.5. Prior to refitting the motor, ensure that the drip shield and mounting-bush are not worn or damaged.6. When refitting the motor plug, ensure correct positioning of the motor plug as shown with all cables

aligned.

N(a) Lower Balance Weight1. Remove the table top (A), dispenser drawer (C) and console panel (D).2. Remove the door seal restraint (G), door interlock (H) and front panel (J).3. Using a 13 mm socket or spanner, remove three balance weight fixing screws.4. Pull the weight forward off its mounting lugs.5. When refitting the balance weight it is essential to ensure that the thread forming screws are

tightened to 24Nm (using a suitable torque-wrench) and that the screws find their original threads, otherwise the thread can be stripped from the plastic drum lug.

N(b) Top Balance Weight1. Remove the table top (A).2. Using a 13 mm socket or spanner, remove three balance weight fixings screws.3. Lift the weight off the drum mountings.4. When refitting the balance weight it is essential to ensure that the thread forming screws are

tightened to 18Nm (using a suitable torque-wrench) and that the screws find their original threads, otherwise the thread can be stripped from the plastic drum lug.

P Heater / Thermistor1. Remove the rear lower access panel (B).2. Remove the heater wiring and detach the thermistor plug.3. Slacken off the 10 mm heater fixing nut and withdraw the heater from the drum.

Q Drum Pulley1. Remove the rear lower access panel (B).2. Carefully peel the belt off the motor pulley taking care not to trap fingers.3. Using a 13mm socket or spanner, remove the fixing bolt in the centre of the pulley.4. Pull the pulley off the drum shaft.5. To ensure adequate pulley security always fit the correct pulley bolt (high tensile with dog-point).

If refitting the original bolt apply an engineering Nutlock (Part No. C00981009) to the bolt threads.

R(a) Suspension Damper1. Remove two suspension clamp fixing screws and unclip the clamp from the chassis.2. Remove the table top (A), dispenser drawer (C) and console panel (D).3. Remove the door seal restraint (G), door interlock (H) and front panel (J).4. Remove the lower balance weight (Na) if access is required to the left-hand damper.5. Unclip any wiring retained within the integral clip on the bottom damper moulding.6. Remove the plastic peg securing the damper to the outer drum using special tool

Part No. C00141734.

18 of 22

Service Manual UK English

Indesit Company

7. Withdraw the suspension damper. The unit should not be split and is not serviceable.8. When reassembling, fit a new plastic peg if the locking-tab on it shows signs of damage.

R(b) Suspension Spring1. Remove the table top (A).2. Unclip any wiring retained within the integral clip on the spring bearing keeper plate.3. Gently lever out the bearing keeper plate with a small flat bladed screwdriver.4. Unhook the spring from the cabinet top rail bearing.

S Dispenser1. Remove the table top (A) and dispenser drawer (C).2. Remove two screws around the dispenser recess and two screws from valve support panel.3. Ease the dispenser backwards to unclip it from the cabinet top rail.4. Remove the dispenser outlet hose, and any harness retention ties.

T Drain Pump1. Remove the lower rear access panel (B).2. Detach the sump hose from the pump using a suitable container to catch any water.3. Disconnect the drain hose from the pump and unplug the wiring connection block.4. Lift plastic the locking tab and slide the pump inwards and lift clear.

U Inner Drum Lifter

1. Insert a small screwdriver onto the 3rd lifter hole from the front of the drum.This will depress the drum flap securing the lifter.

2. Slide the lifter to the front of the drum and remove.3. Before refitting, lift the drum locking tab 3 mm above the drum surface.4. Offer the lifter to the holes in the drum, slide lifter to the back of the drum until a click is heard as

the lifter is locked into place.

V(a) Drum Assembly1. Remove the table top (A).2. Remove the top balance weight (Nb).3. Remove the dispenser drawer (C).4. Remove the console panel (D).5. Remove the dispenser (S).6. Remove the front panel (J).7. Remove the lower balance weight (Na).

3rd hole from the front

19 of 22

Service Manual UK English

Indesit Company

8. Remove the lower rear access panel (B).9. Remove the motor (M).10. Detach the drum from the damper units by removing the two plastic pegs using special

tool Part No. C00141734.11. Remove the sump hose fixing clip and detach the sump hose from the sump chamber.12. Disconnect heater / thermistor wiring and release the wiring harness from the drum clips.13. Unclip any wiring retained within the integral clip on the spring bearing keeper plates.14. Gently lever out the spring bearing keeper plates with a small flat bladed screwdriver.15. Unhook springs from the cabinet top rail bearings.16. Carefully lift the drum assembly out of the cabinet.

V(b) Inner Drum & Support Assembly / Drum Seal / Outer Drum Halves (see note below) 1. Remove the drum assembly (Va).2. Remove the drum pulley (Q).3. Loosen the inner drum assembly by tapping the drum shaft with a soft copper hammer or by

inserting a pin punch into the shaft hole and tapping with a copper hammer.4. Remove sixteen T30 Torx head drum fixing screws and detach the drum front.5. Lift out the inner drum and support assembly.6. The inner drum and support are not designed to be separated, and must be replaced as an

assembly if required.7. Always fit a replacement drum seal if the drum has been split and ensure that the seal joint is at

the top. When reassembling the drum halves it is essential to ensure that the thread forming screws find their original threads, otherwise the thread can be stripped from the plastic drum lugs. Retighten the drum joint fixing screws to 8Nm (using a suitable torque-wrench).

W Cabinet1. Remove the table top (A).2. Remove the dispenser drawer (C) and console panel (D).3. Remove the front panel (J).4. Remove the lower balance weight (Na).5. Remove the lower rear access panel (B).6. Remove the motor (M).7. Remove the top balance weight (Nb).8. Remove the drum assembly (Va).9. Remove the drain pump (T).10. Unscrew the feet, remove the wheels and remove hose clips from the rear of the cabinet.

20 of 22

Service Manual UK English

Indesit Company

X Power Module!

1. Remove the back panel (B). Ensure the module has electrically discharged for 5 minutes before moving to Step 2.Refer to Important note above.

2. Remove the screw or screws securing the module support to the cabinet. 3. Disconnect the wiring - it may be necessary to remove one of the plugs to extract the module from

its location.IMPORTANT NOTE - AVOIDING ELECTRICAL DAMAGE TO THE MODULEBefore disconnecting any plugs it is advisable to note their locations.

4. Lift module clear.

IMPORTANT NOTEThis appliance is manufactured with a '3 phase' motor and uses a different type of power module. This power board is fitted with a large aluminium heat sink which remains live after the power is disconnected. Under no circumstances should the board be removed under the time shown below. Alternative 'quick methods' of discharging the board SHOULD NOT be used or attempted.

21 of 22

Service Manual UK English

Indesit Company

22 of 22

Service Manual UK English