Series C4i, C15i, C25i - Bosch Rexrothw1.boschrexroth.se/pdf/CATALOG_83_275_800.pdf · Series C4i, C15i, C25i Ordering key for single FRL modules or manifolded FRL units 1 How to

Electric Drives and Controls Hydralics

Linear Motion and Assembly Technologies Pneumatics Service

Series C4i, C15i, C25i

Technical data

Series C4i, C15i, C25i Ordering key for single FRL modules or manifolded FRL units

1

How to order FRL modules or FRL units

FRL equipment can be ordered and delivered in different levels:1) As "stand alone units" - Choose the relevant module marked with thread size from the catalogue pages2) As "pre specified complete units" - See the overview and following catalogue pages.3) As "complete systems, customer made" - Contact nearest Bosch Rexroth branch office.4) As units for "self assembling to complete systems" - Follow the steps described below.

How to order modules for "self assembling". Step 1: Choose size

Choose size of modules with respect to port dimension and flow capacity from the list below.(Detailed information can be found at respectively product).

Size Nom. Port Dimension Optional thread Flow capacity, Qn [Nl/min.] (SCFM)

for combined units

C4 G 1/4 G 1/8, G 3/8 900 (31.77)C15 G 1/2 G 1/4, G 3/8 2200 (77.66)C25 G 3/4 G 3/8, G 1/2, G 1 3400 (120.02)

How to order modules for "self assembling". Step 2: Choose functions

Choose the relevant modules and options (if necessary) from the following catalogue pages.The modules shall be marked "without flange".

How to order modules for "self assembling". Step 3: Add flanges with connection thread

Add 1 pair of flanges with connection thread (for inlet and outlet sides).It is recommended to use the nom. dimension on the thread.The tube dimension is then depending on the choosen fittings.

Size Thread Part no.1 pair

C4 G 1/8 5351006002C4 G 1/4 nom. dim. 5351006012C4 G 3/8 5351006022

C15 G 1/4 5351026002C15 G 3/8 5351026012C15 G 1/2 nom. dim. 5351026022

C25 G 3/8 5351036002C25 G 1/2 5351036012C25 G 3/4 nom. dim. 5351036022

C25 G 1 5351036032

How to order modules for "self assembling". Step 4: Add connection keys

Add x number of connection keys for mounting the modules together.x = number of modules -1.

Size Part no.1 piece

C4 5351006072C15 5351026072C25 5351036072

How to order modules for "self assembling". Step 5: Choose pressure gauge

Detailed information about gauges: see separate section under FRL chapter.

2

Series C4i, C15i, C25i Ordering key for single FRL modules or manifolded FRL units

Pressure Gauge G1/8 thread

Scale [bar] (psi) Part no.dia. 40 mm

Part no.dia. 50 mm

0 - 1,6 (0 - 23) 3530200130 35301901500 - 3 (0 - 44) – 35301901200 - 4 (0 - 58) 3530200120 3530190130

0 - 6 (0 - 87) 3530200110 35301901100 - 12 (0 - 174) 3530200150 35601901000 - 16 (0 - 232) 3530200140 3530190140

How to order modules for "self assembling". Step 6: Pilot valves

Add pilot valves to modules: 3/2-way Emergency stop valve and Piloted progressive start-up valves.An Exhaust silencer is recommended for the Emergency stop valve and Isolating valve.Detailed information about Pilot valves and Silencers: see separate section under FRL chapter.

Pilot valveVoltage

Part no.Module C4

Part no.Module C15

Part no.Module C25

24 V DC 5420800390 5420800390 5420770220110 V 50/60 Hz 5420775270 5420775270 5420775270230 V 50/60 Hz 5428200380 5428200380 5420775280

Pneumatic actuation 5351602302 5351602302 5351602302Silencer for exhaust port in

Emergency stop valve and Isolating valve

G 1/4 G 1/2 G 1/2

How to order modules for "self assembling". Example

Background:You need an air flow of about 2000 l/min (71 SCFM).You want to start with a manually operated Isolating valve for shut-off function and have a Filter/Regulator as well as an Emergency Stop valve.

Step 1: Choose size C15. Flow capacity 2200 l/min (78 SCFM).

Step 2: Choose the units from the catalogue pages5352620100 Isolating valve (lockable with padlock)5351320200 Filter/Regulator5351620500 Emergency stop valve

Step 3: Add 1 pair of flanges G 1/2 for size C1 5,5 351 02602 0 from list above.

Step 4: Add 2 connections keys, (3 modules -1 = 2), 5351006072 from list above.

Step 5: Add a pressure gauge dia. 40 mm, 3530200100 from list above

Step 6: Choose a pilot valve 5420800390 + a silencer 5354011130 from list above.

Series C4i, C15i, C25i Isolating valve 1/4 turn 3/2, C4i, C15i and C25i

1

Technical Data

Type Ball valveMax. supply pressure 12 bar (174 psi)Nominal flowat 6 bar (87 psi), ∆p = 1 bar (15 psi)Qn See tableAmbient temperature range +5 °C to +50 °C (+41 °F to +122 °F)

0 °C to +50 °C (+32 °F to +122 °F) with dry airMedium Compressed airWeight C4i, C15i, C25i 0,135 kg (0.298 lbs), 0,3 kg (0.661 lbs),

0,564 kg (1.243 lbs)Diameter of exhaust port C4i, C15i, C25i 1,4 mm, 1,9 mm, 1,9 mm

Materials: Body Zn-diecasting

Part no.

Symbol Series Version Nominal FlowQn [l/min] (SCFM)

Standard With padlock Lockable with key, removable in both

positionsC4i Without flange 5352600000 5352600100 5352600200

G1/8 1170 (41) 5352601000 5352601100 5352601200G1/4 1580 (56) 5352602000 5352602100 5352602200G3/8 1900 (67) 5352603000 5352603100 5352603200

C15i Without flange 5352620000 5352620100 5352620200G1/4 1700 (60) 5352622000 5352622100 5352622200G3/8 4000 (141) 5352623000 5352623100 5352623200G1/2 4900 (173) 5352624000 5352624100 5352624200

C25i Without flange 5352630000 5352630100 5352630200G3/8 4280 (151) 5352633000 5352633100 5352633200G1/2 6300 (222) 5352634000 5352634100 5352634200G3/4 7350 (259) 5352635000 5352635100 5352635200

G1 7630 (269) 5352636000 5352636100 5352636200

Symbol 1) Lockable, Symbol 2) Non-lockable valves.

Accessories (to be ordered separately)

Flanges (only for modules without flange) and Silencer: see Accessories.

2

Series C4i, C15i, C25i Isolating valve 1/4 turn 3/2, C4i, C15i and C25i

Scheme for versions C4i and C25i. Scheme for versions C15i.

¹) C4i exhaust port G1/8 ISO 228/1 C25i exhaust port G1/2 ISO 228/1.²) C15i exhaust port G1/4 ISO 228/1.

Series A B C D E G H I J K M N P Q

C4i 47 37 81,5 20,5 41 33,5 25,5 23,5 46 60 4,2 27 42,5 31,5C15i 63 60 101 31,5 63 36,5 31,5 31,5 82 88 5,1 39,1 64 44,5C25i 80 68 117 36 72 27 43 40 84 102 6,3 40 73 50,5

Series G1/8 G 1/4 G 3/8 G 1/2 G 3/4 G 1

C4i 57 62 62 – – –C15i – 84 92 92 – –C25i – – 97 104 104 125

Series C4i, C15i, C25i Filter C4i and C4i Basic, G 1/8–G 3/8

1

Technical Data

Type Vortex system, with sintered filter andsemi-automatic or automatic drain(optional)

Max. supply pressure 12 bar (174 psi)Nominal flow Qnat 6 bar (87 psi), ∆p = 1 bar (15 psi) See tableAmbient temperature range +5 °C to +50 °C (+41 °F to +122 °F)

0 °C to +50 °C (+32 °F to +122 °F) with dry airMedium Compressed airWeight 0,3 kg (0.66 lbs)

Materials Body Zn-diecastingBowl Polyamide - with composite bowl guard

Polycarbonate - without bowl guard(basic)

Filter porosity 25 µm or 5 µm (optional)Bowl capacity 4 cl (1.35 U.S.Fl.oz)

Part no.

Symbol Threaded portsISO 228/1

Nominal flowQn [Nl/ min.] (SCFM)

With options Part no.

G 1/8 800 (28) – 5351201000G 1/4 1125 (40) – 5351202000G 1/4 1125 (40) Metal bowl and manual drain 8901703570G 3/8 1200 (42) – 5351203000

Without flange – – 5351200000Without flange – Automatic drain 5351200020Without flange – Filter 5 µm 5351200010Without flange – Without bowl guard 5352200000


Filter cartridge 25 µm, 5351200012Plastic bowl, 5351200042Spare parts kit, complete, 5 µm, 5351200022Automatic drain cartridge, 8901700102Spare parts kit, complete, 25 µm, 5351200002Plastic bowl for use with metal guard, 5351200052Filter cartridge 5 µm, 5351200032Metal bowl, 5351200062Flanges (only for modules without flange): see Accessories

2

Series C4i, C15i, C25i Filter C4i and C4i Basic, G 1/8–G 3/8

C4i Standard C4i Basic

* Connection for tube dia. 10x1.

Threaded ports ISO 228/1 A

G 1/8 57G 1/4 62G 3/8 62

Series C4i, C15i, C25i Filter C15i, G 1/4–G 1/2

1

Technical Data

Type Vortex system, with sintered filter andsemi-automatic or automatic drain(optional)

Max. supply pressure 12 bar (174 psi)Nominal flow Qnat 6 bar (87 psi), ∆p = 1 bar (15 psi) See tableAmbient temperature range +5 °C to +50 °C (+41 °F to +122 °F)


Materials Body Zn-diecastingBowl Polyamide - with metal bowl guard


Part no.


Nominal flowQn [Nl / min.] (SCFM)


G 1/4 2400 (85) – 5351222000G 3/8 3480 (123) – 5351223000G 3/8 3480 (123) Metal bowl and manual drain 8901703580G 3/8 3480 (123) Metal bowl and manual drain 8901703580G 1/2 3600 (127) – 5351224000

Without flange – – 5351220000Without flange – Automatic drain 5351220020Without flange – Filter 5 µm 5351220010


Filter cartridge 25 µm, 5351220012Filter cartridge 5 µm, 5351220032Plastic bowl, 5351220042Plastic bowl for use with metal guard, 5351220052Metal bowl, 5351220062Automatic drain cartridge, 8901700142Spare parts kit, complete, 5 µm, 5351220022Automatic drain cartridge, 8901700142Flanges (only for modules without flange): see Accessories



G 1/4 84G 3/8 92G 1/2 92

Series C4i, C15i, C25i Filter C25i, G 3/8–G 1

1

Technical Data

Type Vortex system, with sintered filter andsemi-automatic or automatic drain (optional)

Max. supply pressure 12 bar (174 psi)Nominal flow Qnat 6 bar (87 psi) and ∆p = 1 bar (15 psi) See tableAmbient temperature range +5 °C to +50 °C (+41 °F to +122 °F)

0 °C to +50 °C (+32 °F to +122 °F)Medium Compressed airWeight 1,1 kg (2.43 lbs)



Part no.




G 3/8 3400 (120) – 5351233000G 1/2 5000 (177) – 5351234000

G 1/2 5000 (177) Metal bowl with sight glassand manual drain 8901700610

G 3/4 5500 (194) – 5351235000

G 3/4 5500 (194) Metal bowl with sight glassand manual drain 8901700620

G 1 5700 (201) – 5351236000Without flange – – 5351230000Without flange – Automatic drain 5351230020Without flange – Filter 5 µm 5351230010


Filter cartridge 25 µm, 5351230012Metal bowl with sight glass, 5351230072Spare parts kit, complete, 5 µm, 5351230022Metal bowl 5351230062Spare parts kit, complete, 25 µm, 5351230002Automatic drain 8901700142Filter cartridge 5 µm, 5351230032Plastic bowl 5351230042Plastic bowl for use with metal guard, 5351230052Flanges (only for modules without flange): see Accessories

2

Series C4i, C15i, C25i Filter C25i, G 3/8–G 1



G 3/8 97G 1/2 104G 3/4 104G 1 125

Series C4i, C15i, C25i Pre- & Coalescing filter C4i, G 1/8–G 3/8

1

Technical Data

Type Vortex system and sintered filter withborosilicate micro-fibrous filter and semi-automatic drain

Max. supply pressure 12 bar (174 psi)Nominal flow Qnat 6 bar (87 psi) and ∆p = 0.140 bar (2 psi) See tableAmbient temperature range +5 °C to +50 °C (+41 °F to +122 °F)



Filter porosity Pre-filter 5 µmFilter 0,01 µm

Bowl capacity 4 cl (1.35 U.S.Fl.oz)

Part no.



With option Part no.

G 1/8 150 (5.3) – 5351901810G 1/4 190 (6.7) – 5351902810G 3/8 190 (6.7) – 5351903810

Without flange – – 5351900810Without flange – Automatic drain 5351900830


Filter cartridge 5 µm, 5351200032Filter cartridge 0,01 µm, 5351200802Plastic bowl for use with metal guard, 5351200052Plastic bowl, basic, 5351200042Metal bowl, 5351200062Automatic drain cartridge, 8901700102Spare parts kit, complete 5 µm, 5351200022Flanges (only for units without flange): see Accessories



G 1/8 95G 1/4 99G 3/8 99

Series C4i, C15i, C25i Pre- & Coalescing filter C15i, G 1/4–G 1/2

1

Technical Data

Type Vortex system and sintered filter withborosilicate micro-fibrous filter and semi-automatic drain






Part no.




G 1/4 410 (15) – 5351922810G 3/8 445 (16) – 5351923810G 1/2 450 (16) – 5351924810



Filter cartridge 5 µm, 5351220032Filter cartridge 0,01 µm, 5351220802Plastic bowl for use with metal guard, 5351220052Metal bowl, 5351220062Spare parts kit, complete 5 µm, 5351220022Automatic drain cartridge, 8901700142Plastic bowl, 5351220042Flanges (only for units without flange): see Accessories



G 1/4 144G 3/8 152G 1/2 152

Series C4i, C15i, C25i Pre- & Coalescing filter C25i, G 3/8–G 1

1

Technical Data

Type Vortex system and sintered filter regulator with borosilicate micro-fibrous filter and semi-automatic drain


0 °C to +50 °C (+32 °F to +122 °F) with dry airMedium Compressed airWeight 2 kg (4.41 lbs)




Part no.




G 3/8 430 (15) – 5351933810G 1/2 530 (19) – 5351934810G 3/4 530 (19) – 5351935810G 1 530 (19) – 5351936810



Filter cartridge 5 µm, 5351230032Filter cartridge 0,01 µm, 5351230802Plastic bowl for use with metal guard, 5351230052Metal bowl, 5351230062Plastic bowl, basic, 5351230042Spare parts kit, complete 5 µm, 5351230022Automatic drain cartridge, 8901700142Flanges (only for units without flange): see Accessories



G 3/8 165G 3/4 172G 1/2 172G 1 193

Series C4i, C15i, C25i Filter regulator & Coalescing filter C4i, G 1/8–G 3/8

1

Technical Data

Type Diaphragm filter regulator, self-relieving with sintered pre-filter - coalescing filter unitwith micro-fibrous borosilicate andsemi-automatic drain.

Max. supply pressure 12 bar (174 psi)Secondary pressure 0,5–10 bar (7–145 psi)Nominal flow Qn See tableat primary pressure = 7 bar (102 psi)secondary pressure = 6 bar (87 psi) and∆p = 0.140 bar (2 psi)Ambient temperature range +5 °C to +50 °C (+41 °F to +122 °F)



Filter porosity Prefilter 5 µmFilter 0,01 µm


Part no.


Nominal flowQn [NI / min.] (SCFM)


G 1/8 150 (5.30) – 5351901210G 1/4 190 (6.71) – 5351902210G 3/8 190 (6.71) – 5351903210



Filter regulator, 5351300012 including spare parts for filter C4i, 5 µmPressure gaugeSee filter unit C4iFlanges (only for units without flange): see Accessories

* Connection for pressure gauge G 1/8.** Connection for tube dia. 10x1.


G 1/8 95G 1/4 99G 3/8 99

Series C4i, C15i, C25i Filter regulator & Coalescing filter C15i, G 1/4–G 1/2

1

Technical Data

Type Diaphragm filter regulator, self-relieving with sintered pre-filter - coalescing filter unitwith micro-fibrous borosilicate and semi-automatic drain.






Part no.




G 1/4 410 (14.4) – 5351922210G 3/8 445 (15.7) – 5351923210G 1/2 450 (15.9) – 5351924210



Spare parts kit for filter regulator, 5351320012 and 5351420022Pressure gauge see AccessoriesSee filter unit C15iFlanges (only for units without flange): see Accessories

** Connection for tube dia. 10x1.* Connection for pressure gauge: G 1/8.

Threaded ports ISO 228 / 1 A

G 1/4 144G 3/8 152G 1/2 152

Series C4i, C15i, C25i Filter regulator & Coalescing filter C25i, G 3/8–G 1

1

Technical Data

Type Diaphragm filter regulator, self-relieving with sintered pre-filter - coalescing filter unitwith micro-fibrous borosilicate andsemi-automatic drain.






Part no.

Symbol Threaded portsISO 228 / 1



G 3/8 430 (15) 5351933210G 1/2 530 (19) 5351934210G 3/4 530 (19) 5351935210G 1 530 (19) 5351936210

Without flange 5351930210Without flange Automatic drain 5351930230


Spare parts kit for filter regulator, 5351230022 and 5351430022.Pressure gauge: see Accessories.See filter unit C25i.Flanges (only for units without flange): see Accessories

* Connection for pressure gauge: G 1/8.** Connection for tube dia. 10x1.

Threaded ports ISO 228 / 1 A

G 3/8 165G 1/2 172G 3/4 172G 1 193

Series C4i, C15i, C25i Pressure Regulator C4i, G 1/8–G 3/8

1

Technical Data

Type Diaphragm regulating valve,Max. supply pressure 12 bar (174 psi)Secondary pressure range 0,5–10 bar (7–145 psi) or

0,1–3 bar (1–44 psi) (optional)Nominal flow Qnat primary pressure = 7 bar (102 psi)secondary pressure = 6 bar (87 psi) and See table∆p = 1 bar (15 psi)Ambient temperature range +5 °C to +50 °C (+41 °F to +122 °F)


Materials Body Zn-diecasting

Part no.




G 1/8 850 (30) – 5351401200G 1/4 1400 (49) – 5351402200G 3/8 1400 (49) – 5351403200

Without flange – – 5351400200Without flange – 0,1–3 bar (1–44 psi) 5351400300

Without flange – With lockable control knob, without lock (1) 5351400210


Lock Part no. : 5351005302 for use with pressure regulator.Pressure gauge see Accessories.Spare parts kit, 5351400002.Flanges (only for modules without flange): see Accessories

* Connection for pressure gauge G 1/8 ISO 228/1.


G 1/8 58G 1/4 62G 3/8 62

Series C4i, C15i, C25i Manifold Regulator, C4i, G 1/4, G 3/8

1

Technical Data

Type Diaphragm regulator,Max. supply pressure 12 bar (174 psi)Secondary pressure range 0,5–10 bar (7–145 psi) or

0,1–3 bar (1–44 psi) (optional)Nominal flow Qnat primary pressure 7 bar (102 psi),secondary pressure = 6 bar (87 psi) and See table∆p = 1 bar (15 psi)Ambient temperature range +5 °C to +50 °C (+41 °F to +122 °F)


Materials Body Zn-diecastingPressure port G 1/8Outlet port G 1/4

Technical informationThese regulators permit a wide range of outlet pressures from a common supply (two ports).Supplied without flanges or pressure gauge.

Part no.

Symbol Threaded inlet port Nominal flowQn [Nl / min.] (SCFM)

With options [bar] (psi) Part no.

Without flange or pressure gauge – 5352400200Without flange or pressure gauge 0,1-3 (1-44) 5352400300

G 1/4 without pressure gauge 1 400 (49) – 5352402200G 1/4 without pressure gauge 0,1-3 (1-44) 5352402300G 3/8 without pressure gauge 1 400 (49) – 5352403200G 3/8 without pressure gauge 0,1-3 (1-44) 5352403300


Mini pressure gauge part no. 8901701270.Flanges (only for units without flange): see AccessoriesConnecting flanges: see Accessories

* Connection for pressure gauge: G 1/8 ISO 228/1.** Connection for outlet pressure: G 1/4 ISO 228/1.*** 2 connections for inlet pressure G 1/4 or G 3/8 according to ISO 228/1 (corresponding to usable flange sizes).A = 25 mm + 37 mm x nB = 9 mm + 37 mm x nC = 23 mm + 37 mm x nn = number of regulators.

Series C4i, C15i, C25i Pressure Regulator C15i, G 1/4–G 1/2

1

Technical Data


0,1–3 bar (1–44 psi) (optional)Nominal flow Qnat primary pressure =7 bar (102 psi);secondary pressure = 6 bar (87 psi) and See table∆p = 1 bar (15 psi)Ambient temperature range +5 °C to +50 °C (+41 °F to +122 °F)



Part no.

Symbol Threaded portISO 228/1


With options Part no.without pressure gauge

G 1/4 2500 (88) – 5351422200G 3/8 2800 (99) – 5351423200G 1/2 3500 (124) – 5351424200



Without flange – With lockable control knob, built-in lock (2) (E11 H1) 8901701340


Lock Part no. : 5351005302 for use with pressure regulator.Pressure gauge: see Accessories. Spare parts kit, 5351420002.Flanges (only for modules without flange): see Accessories

* Connection for pressure gauge: G 1/8.


G 1/4 84G 3/8 92G 1/2 92

Series C4i, C15i, C25i Pressure Regulator C25i, G 3/8–G 1

1

Technical Data


0,1–3 bar (1–44 psi) (optional)Nominal flow Qn at primary pressure =7 bar (102 psi)secondary pressure = 6 bar (87 psi) and See table∆p = 1 bar (15 psi)Ambient temperature range +5 °C to +50 °C (+41 °F to +122 °F)



Part no.




G 3/8 3600 (127) – 5351433200G 1/2 5250 (185) – 5351434200G 3/4 5300 (187) – 5351435200G 1 5300 (187) – 5351436200





Lock Part no. : 5351005302 for use with pressure regulator, see Accessories.Pressure gauge: see Accessories.Spare parts kit, 5351430002.Flanges (only for modules without flange): see Accessories

* Connection for pressure gauge: G 1/8.


G 3/8 97G 1/2 104G 3/4 104G 1 125

Series C4i, C15i, C25i Manifold Regulator C25i, G 3/8–G 1

1

Technical Data

Type Rolling diaphragm regulator,[mm]

Max. supply pressure 12 bar (174 psi)Secondary pressure range 0,5 to 10 bar(7 to 145 psi) or

0,1–3 bar (1–44 psi) (optional)Nominal flow Qnat primary pressure 7 bar (102 psi),secondary pressure = 6 bar (87 psi) and (see table)∆p = 1 bar (15 psi)Ambient temperature range +5 °C to +50 °C (+41 °F to +122 °F)



Pressure port G 1/8Outlet port G 1/2

Technical informationThese regulators permit a wide range of outlet pressures from a common supply (two ports).Supplied without flanges or pressure gauge.

Part no.

Symbol Threaded inlet port Nominal flowQn [Nl / min.] (SCFM)

With options [bar] (psi) Part no.

Without flange or pressure gauge – 0,5–10 (7–145) 5352430200Without flange or pressure gauge – 0,1–3 (1–44) 5352430300

G 1/2 without pressure gauge 5300 (187) 0,5–10 (7–145) 5352434200G 1/2 without pressure gauge – 0,1–3 (1–44) 5352434300G 3/4 without pressure gauge 5300 (187) 0,5–10 (7–145) 5352435200G 3/4 without pressure gauge – 0,1–3 (1–44) 5352435300

* Connection for pressure gauge: G 1/8.** Connection for outlet pressure: G 1/2 ISO 228/1.*** 2 connections for inlet pressure according to ISO 228/1 (corresponding to usable flange sizes.)A = 29 mm + 68 mm x n.B = 16 mm + 68 mm x n.n = number of regulators.

Accessories

GaugesFlanges (only for units without flange): see AccessoriesConnecting flanges: see AccessoriesSpare parts kit 5351430002

* Connection for pressure gauge: G 1/8 ISO 228/1.** Connection for outlet pressure: G 1/2 ISO 228/1.*** 2 connections for inlet pressure according to ISO ISO 228/1 (corresponding to usable flange sizes).A = 29 mm + 68 mm x n.B = 16 mm + 68 mm x n.n = number of regulators.

Series C4i, C15i, C25i Filter regulator C4i and C4i Basic, G 1/8–G 3/8

1

Technical Data

Type Diaphragm regulator, self-relievingwith sintered filter and semi-automaticor automatic drain

Max. supply pressure 12 bar (174 psi)Secondary pressure 0,5–10 bar (7–145 psi)Nominal flow Qn at primary pressure = 7 bar (102 psi),secondary pressure = 6 bar (87 psi) and See table∆p=1 bar (15 psi)Ambient temperature range +5 °C to +50 °C (+41 °F to +122 °F)



Polycarbonate - without bowl guard (basic)

Bowl capacity 4 cl (1.35 U.S.Fl.oz)Filter porosity 25 µm or 5 µm (optional)

Part no.




G 1/8 700 (25) – 5351301200G 1/4 990 (34.95) – 5351302200G 1/4 – Metal bowl and manual drain 8901701460G 3/8 1000 (35) – 5351303200



Without flange – Filter 5 µm 5351300210Without flange – Without bowl guard 5352300200


Lock Part no. : 5351005302, see Accessories.Pressure gauge see Accessories.Filter, 25 µm 5351200002.Filter 5 µm, 5351200022.Regulator, 5351400002, includes all spare parts for C4i filters.Flanges (only for modules without flange): see Accessories

2

Series C4i, C15i, C25i Filter regulator C4i and C4i Basic, G 1/8–G 3/8




G 1/8 58G 1/4 62G 3/8 62

Series C4i, C15i, C25i Filter regulator C15i, G 1/4–G 1/2

1

Technical Data


Max. supply pressure 12 bar (174 psi)Secondary pressure 0,5–10 bar (7–145 psi)Nominal flow Qn at primary pressure =7 bar (102 psi)secondary pressure = 6 bar (87 psi) and See table∆p=1 bar (15 psi)Max. temperature +50 °C (+122 °F)




Part no.




G 1/4 2100 (74) – 5351322200G 3/8 2800 (99) – 5351323200G 3/8 – Metal bowl and manual drain 8901702480G 1/2 3300 (116) – 5351324200

Without flange – – 5351320200Without flange – Automatic drain 5351320220Without flange – Filter 5 µm 5351320210




Lock Part no. : 5351005302, see Accessories.Pressure gauge: see Accessories.Filter, 25 µm 5351220002.Filter, 5 µm, 5351220022.Regulator, 5351420002, includes all spare parts for C15i filters.Flanges (only for modules without flange): see Accessories

2

Series C4i, C15i, C25i Filter regulator C15i, G 1/4–G 1/2



G 1/4 84G 3/8 92G 1/2 92

Series C4i, C15i, C25i Filter regulator C25i, G 3/8–G 1

1

Technical Data


Max. supply pressure 12 bar (174 psi)Secondary pressure 0,5–10 bar (7–145 psi)Nominal flow Qnat primary pressure =7 bar (102 psi);secondary pressure = 6 bar (87 psi) and See table∆p=1 bar (15 psi)Ambient temperature range +5 °C to +50 °C (+41 °F to +122 °F)




Part no.




G 3/8 3300 (116) – 5351333200G 1/2 4000 (141) – 5351334200

G 1/2 – Metal bowl with sight glassand manual drain 8901700720

G 3/4 4440 (157) – 5351335200

G 3/4 – Metal bowl with sight glassand manual drain 8901700680

G 1 4700 (166) – 5351336200Without flange – – 5351330200Without flange – Automatic drain 5351330220Without flange – Filter 5 µm 5351330210




Lock Part no : 5351005302.Pressure gauge: see Accessories.Spare parts kit, Filter, 25 µm, 5351230002.Filter, 5 µm, 5351230022.Regulator, 5351430002 , includes all spare parts for C25i filters.Flanges (only for modules without flange): see Accessories.

2

Series C4i, C15i, C25i Filter regulator C25i, G 3/8–G 1

* Connection for pressure gauge G 1/8.** Connection for tube dia. 10x1.


G 3/8 97G 1/2 104G 3/4 104G 1 125

Series C4i, C15i, C25i Lubricator C4i and C4i Basic, G 1/8–G 3/8

1

Technical Data

Type Proportional mist lubricatorMax. supply pressure 12 bar (174 psi)Nominal flow Qnat 6 bar (87 psi) and ∆p = 1 bar (15 psi) See tableAmbient temperature range +5 °C to +50 °C (+41 °F to +122 °F)

0 °C to +50 °C (+32 °F to +122 °F) with dry airMedium Compressed airOil viscosity at 40 °C (104 °F) 9–11 mm²/sWeight 0,3 kg (0.66 lbs)


Polycarbonate* - without bowl guard (basic)


This device is equipped with a system that permits the filling of the lubricator by means of a fitting located at the lower part of the bowl which can be connected to a tank.By pressing the filling button the operator opens a venturi which creates a vacuum in the upper part of the bowl, this enabling the oil in the tank to be sucked up.

* Note! Polycarbonate does not withstand oils with aggressive compounds, e.g alcohols. We recommend oil of the ATF-DEXRON type (part no. 8982000010)or oil with an aniline point of 93 °C ±5 °C.(199 °F ±41 °F)

Part no.




G 1/8 1000 (35) – 5351501000G 1/4 1600 (56) – 5351502000G 3/8 1700 (60) – 5351503000

Without flange – – 5351500000

Without flange – Basic 5352500000


Plastic bowl, basic, 5351500002.Plastic bowl for use with metal guard, 5351500012.Metal bowl, 5351500022.Sight glass, 5351500032.Flanges (only for modules without flange): see Accessories.

2

Series C4i, C15i, C25i Lubricator C4i and C4i Basic, G 1/8–G 3/8


* Push button for filling of the lubricator.


G 1/8 58G 1/4 62G 3/8 62

Series C4i, C15i, C25i Lubricator C15i, G 1/4–G 1/2

1

Technical Data






Part no.

Symbol Threaded ports ISO 228/1 Nominal flow Qn [NI / min.] (SCFM) Part no.G 1/4 2500 (88) 5351522000G 3/8 3600 (217) 5351523000G 1/2 4100 (145) 5351524000

Without flange – 5351520000


Plastic bowl, basic, 5351520002.Plastic bowl for use with metal guard, 5351520012.Metal bowl, 5351520022.Sight glass, 5351520032.Flanges (only for modules without flange): see Accessories.



G 1/4 84G 3/8 92G 1/2 92

Series C4i, C15i, C25i Lubricator C25i, G 3/8–G 1

1

Technical Data






Part no.


Nominal flow Qn [Nl / min.] (SCFM) Part no.

G 3/8 4500 (159) 5351533000G 1/2 6700 (237) 5351534000G 3/4 6800 (240) 5351535000G 1 6800 (240) 5351536000

Without flange – 5351530000


Plastic bowl, basic, 5351530002.Plastic bowl for use with metal guard, 5351530012.Metal bowl, 5351530022.Sight glass, 5351520032.Metal bowl with sight glass, 5351530032.Flanges (only for modules without flange): see Accessories.



G 3/8 97G 1/2 104G 3/4 104G 1 125

Series C4i, C15i, C25i Combination FR+L unit C4i and C4i Basic, G 1/8–G 3/8

1

Technical Data

Type Diaphragm regulator, self-relievingwith filter with semi-automatic drain(manual and automatic drain as option)and proportional mist lubricator

Max. supply pressure 12 bar (174 psi)Secondary pressure 0,5–10 bar (7–145 psi)Nominal flow Qn secondary pressure = 6 bar (87 psi) and See table∆p=1 bar (15 psi)Ambient temperature range +5 °C to +50 °C (+41 °F to +122 °F)



Polycarbonate - without bowl guard

Bowl capacity Filter 4 cl (1.35 U.S.Fl.oz)Lubricator 4 cl (1.35 U.S.Fl.oz)

Filter porosity 25 µm or 5 µm (optional)

Part no.



With options Part no.with pressure gauge

G 1/8 620 (22) - 5351001000G 1/4 900 (32) - 5351002000G 3/8 910 (32.12) - 5351003000

Without flange - automatic drain 5351000020without flange without bowl guard 5352000000


Spare parts kits : see filter regulator C4i and lubricator C4i.Flanges (only for units without flange): see Accessories.

2

Series C4i, C15i, C25i Combination FR+L unit C4i and C4i Basic, G 1/8–G 3/8


* Push buttton for filling of the lubricator.** Connection for tube dia. 10x1.


G 1/8 95G 1/4 99G 3/8 99

Series C4i, C15i, C25i Combination FR+L unit C15i, G 1/4–G 1/2

1

Technical Data

Type Diaphragm regulator, self-relievingwith filter with semi-automatic drain(manual and automatic drain as option)and proportional mist lubricator

Max. supply pressure 12 bar (174 psi)Secondary pressure 0,5–10 bar (7–145 psi)Nominal flow Qn at primary pressure =7 bar (102 psi);secondary pressure = 6 bar (87 psi) and See table∆p=1 bar (15 psi)Ambient temperature range +5 °C to +50 °C (+41 °F to +122 °F)

0 °C to +50 °C (+32 °F to +122 °F) with dry airMedium Compressed airWeight 1,43 kg (3.15 psi)




Part no.




G 1/4 1200 (42) – 5351022000G 3/8 2100 (74) – 5351023000G 1/2 2500 (88) – 5351024000

Without flange – Automatic drain 5351020020


Spare parts kits : see filter regulator C15i and lubricator C15i.Flanges (only for units without flange): see Accessories.

* Push buttton for filling of the lubricator.** Connection for tube dia. 10x1.


G 1/4 144G 3/8 152G 1/2 152

Series C4i, C15i, C25i Combination FR+L unit C25i, G 3/8–G 1

1

Technical Data

Type Diaphragm regulator, self-relievingwith semi-automatic drain(manual and automatic drain as option)filter and proportional mist lubricator.

Max. supply pressure 12 bar (174 psi)Secondary pressure 0,5–10 bar (7–145 psi)Nominal flow Qn at supply pressure = 7 bar (102 psi);delivery pressure = 6 bar (87 psi) and See table∆p=1 bar (15 psi)Ambient temperature range +5 °C to +50 °C (+41 °F to +122 °F)





Part no.




G 3/8 2900 (102) – 5351033000G 1/2 3700 (131) – 5351034000G 3/4 3800 (134) – 5351035000G 1 3800 (134) – 5351036000

Without flange – Automatic drain 5351030020


Spare parts kit : see filter regulator C25i and lubricator C25i.Flanges (only for units without flange): see Accessories.

* Push button for filling of the lubricator.** Connection for tube dia. 10x1.


G 3/8 165G 1/2 172G 3/4 172G 1 193

Series C4i, C15i, C25i Combination F+R+L unit C4i and C4i Basic, G 1/8–G 3/8

1

Technical Data

Type Diaphragm regulator,with semi-automatic drain(manual and automatic drain as option)filter and proportional mist lubricator.

Max. supply pressure 12 bar (174 psi)Secondary pressure 0,5–10 bar (7–145 psi)Nominal flow Qn at primary pressure = 7 bar (102 psi);secondary pressure = 6 bar (87 psi) and See table∆p=1 bar (15 psi)Ambient temperature range +5 °C to +50 °C (+41 °F to +122 °F)



Polycarbonate - without bowl guard (Basic)



Part no.



Part no.With pressure gauge

G 1/8 590 (21) 5351101000G 1/4 860 (30) 5351102000G 3/8 890 (31) 5351523000

Basic without flange – 5352100000


Spare parts kit : see filter C4i, regulator C4i and lubricator C4i.Flanges (only for units without flange): see Accessories.


* Connection for tube dia. 10x1.** Push button for filling of the lubricator.


G 1/8 132G 1/4 136G 3/8 136

Series C4i, C15i, C25i Combination F+R+L unit C15i, G 1/4–G 1/2

1

Technical Data

Type Diaphragm regulator, filter withsemi-automatic drain(manual and automatic drain as option)and proportional mist lubricator.

Max. supply pressure 12 bar (174 psi)Secondary pressure 0,5–10 bar (7–145 psi)Nominal flow Qn at primary pressure = 7 bar (102 psi);secondary pressure = 6 bar (87 psi) and See table∆p=1 bar (15 psi)Ambient temperature range +5 °C to +50 °C (+41 °F to +122 °F)





Part no.




G 1/4 1800 (64) 5351122000G 3/8 1900 (67) 5351123000

G 1/2 2200 (78) 5351124000


Spare parts kits : see filter C15i, regulator C15i and lubricator C15i.

* Push button for filling of the lubricator.** Connection port for tube dia. 10x1.


G 1/4 204G 3/8 212G 1/2 212

Series C4i, C15i, C25i Combination F+R+L unit C25i, G 3/8–G 1

1

Technical Data

Type Diaphragm regulator, filterwith semi-automatic drain(manual and automatic drain as option)and proportional mist lubricator.


0 °C to +50 °C (+32 °F to +122 °F)Medium Compressed airWeight 3,85 kg (8.59 lbs)




Part no.




G 3/8 2600 (92) 5351133000G 1/2 3300 (116) 5351134000G 3/4 3400 (120) 5351135000G 1 3500 (124) 5351136000


Spare parts kits : see filter C25i, regulator C25i and lubricator C25i.

* Push button for filling of the lubricator.** Connection for tube dia. 10x1.


G 3/8 233G 1/2 240G 3/4 240G 1 261

Series C4i, C15i, C25i Emergency stop valve C4i, C15i, C25i

1

Technical Data

Type Poppet valve Supply pressure 4 to 10 bar (58 to 145 psi)Nominal flow Qnat 6 bar (87 psi), ∆p = 1 bar (15 psi) See tableAmbient temperature range +5 °C to +50 °C (+41 °F to +122 °F)

0 °C to +50 °C (+32 °F to +122 °F) with dry airMedium Compressed air, lubricated or non-lubricatedWeight See table

Materials Body Zn-diecastingSeals Nitrile rubber

Actuation can be :1. Pneumatic by means of pilot port Part no. 53516023022. Solenoid (CNOMO connection) by means of pilot valve

ApplicationIntegration of a pneumatic or solenoid 3/2 emergency stop valve into the compressed air preparation unit.This valve is used as a shut-off and rapid exhaust valve and for start-up of compressed air by remote signal.

Part no.

Symbol Series Weight [kg] (lbs) Nominal flowQn [l/min] (SCFM)

Part no.without flange or pilot

C4i 0,3 (0.66) 1000 (35) 5351600500C15i 0,6 (1.32) 3200 (113) 5351620500

C25i 1,2 (2.65) 4500 (159) 5351630500


Flanges, Pneumatic pilot port, Silencer: see Accessories.Solenoid pilot valve: see Other Products.

Series C4i and C25i Series C15i

* Mounting surface.

Series A B C D E F G H I J L M N P R

C4i 73 37 20,5 41 47 23,5 8,5 40 46 60 4,2 27 42,5 G 1/4 10C15i 99 60 31,5 63 63 31,5 3 64,5 82 88 5,1 39,1 64 G 1/2 18C25i 107,5 68 36 72 80 40 1,5 60 84 102 6,3 40 73 G 1/2 21

K G1/8 G 1/4 G 3/8 G 1/2 G 3/4 G 1

C4i 57 62 62 – – –C15i – 84 92 92 – –C25i – – 97 104 104 125

Series C4i, C15i, C25i Adjustable progressive start-up valve, C4i, C15i, C25i

1

Technical Data

Type Poppet valve, spring-loaded, adjustable,with integral throttle

Supply pressure 4 to 10 bar (58 to 145 psi)Nominal flow Qnat 6 bar (87 psi), ∆p = 1 bar (15 psi) See tableAmbient temperature range +5 °C to +50 °C (+41 °F to +122 °F)



Technical informationFunction:1. Secondary pressure builds up gradually in the system. The moving parts in the system advance slowly to their initial position.2. On reaching the threshold pressure, the start-up valve diverts the full primary pressure into the system.

ApplicationSystem for progressive increase of pressure:- Adjustable pressure build-up via removable integral throttle (throttle 0,8 mm dia.; 5 additional larger throttles supplied).- Full pressure threshold from 4 to 7 bar (58 to 102 psi) (at pv = 10 bar (145 psi)).- Adjusting knob lead-sealed.

Part no.


Part no.without flange

C4i 0,2 (0.44) 1150 (41) 5351600100C15i 0,6 (1.32) 3800 (134) 5351620100

C25i 1,1(2.43) 5480 (193) 5351630100


Flanges see Accessories.


Series A B C D E F G H I K L M N

C4i 91,5 37 41 41 47 23,5 68 46 60 4,2 27 42,5 0C15i 156 60 31,5 63 63 40 134 81 88 5,1 39,1 73 3C25i 174 68 72 72 80 31,5 121 84 102 6,3 40 64 0

2

Series C4i, C15i, C25i Adjustable progressive start-up valve, C4i, C15i, C25i

J G1/8 G1/4 G3/8 G1/2 G3/4 G1

C4i 57 62 62 – – –C15i – 84 92 92 – –C25i – – 97 104 104 125

Series C4i, C15i, C25i Piloted progressive start-up Valve and Unit Series C25i

1

Technical Data

Type Poppet valve with throttle preceded by 3/2 NCPoppet valve in unit

Supply pressure Valve: 0,5–10 bar (7–145 psi) (extern. pilot),3–10 bar (44–145 psi) (intern. pilot)

Unit: 4–10 bar (58–145 psi)Nominal flowat 6 bar (87 psi), ∆p = 1 bar (15 psi)Qn See tableAmbient temperature range +5 °C to +50 °C (+41 °F to +122 °F)

0 °C to +50 °C (+32 °F to +122 °F) with dry airMedium Compressed airWeight See table

Materials Zn-diecasting, AlNBR (Nitrile Butadiene Rubber)

Technical informationFunction:- Valve: Secondary pressure builds up gradually due to a nozzle (one of 0,8 mm dia. is built-in and a further 5 nozzles with greater diameters are supplied).Max. flow is only attained when the piloting system is activated by a control component and all conditions defined by the user are satisfied (Programmable controller for example).- Unit: Associates the function of the emergency stop valve and of the piloted progressive start-up valve (see above).Pilot control can be either solenoid (with CNOMO interface) or pneumatic pilot port.Control pressure is 3 to 10 bar (44 to 145 psi).This valve is supplied without flanges.

ApplicationSystem for progressive increase of pressure and slow motion during start-up:- Adjustable pressure build-up via removable integral nozzle (nozzle 0,8mm dia.; 5 additional larger nozzles supplied).Unit for same application including an emergency stop valve allowing fast shut-off of the system.

Part no.

Symbol Description Weight [kg] (lbs) Nominal flowQn [l/min] (SCFM)

Part no.¹)

Valve 0,800 (1.76) 5100 (180) 8901700140

Unit 1,880 (4.14) 3420 (121) 5351833650

¹) Without pilot, flange, nor pressure gauge


Flanges see Accessories.Solenoid pilot, Pneumatic pilot port, Pressure gauges and Silencers: see Accessories.

2

Series C4i, C15i, C25i Piloted progressive start-up Valve and Unit Series C25i

Valve Unit

* 2 threads M4.** CNOMO/AFNOR E49-066 mounting surface.

Threaded ports ISO 228/1 A L

G 3/8 97 165G 1/2 104 172G 3/4 104 172G 1 125 193

Series C4i, C15i, C25i Progressive start-up units C4i, C15i, C25ipneumatic or solenoid actuation

1

Technical Data

Type 3/2-way piloted valve, with progressive start-up valve

Supply pressure 4 to 10 bar (58 to 145 psi)Nominal flow Qnat 6 bar (87 psi), ∆p = 1 bar (15 psi) See tableAmbient temperature range +5 °C to +50 °C (+41 °F to +122 °F)



Technical informationFunction:1.) 3/2 valve is actuated (solenoid or pneumatic)2.) Secondary pressure builds up gradually in the system.The moving parts in the system advance slowly to their initial position.3.) On reaching the pressure threshold, the start-up valve diverts the full primary pressure into the system.

ApplicationSystem for progressive increase of pressure:- Adjustable pressure build-up via removable integral throtte (throttle 0,8 mm dia.; 5 additional larger throttles supplied).- Full pressure threshold from 4 to 7 bar (58 to 102 psi) (at pv = 10 bar (145 psi)).- Adjusting knob can be lead-sealed.

Part no.


Part no.without pilot, flange or

pressure gaugeC4i 0,5 (1.10) 900 (32) 5351600150

C15i 1,4 (3.09) 3000 (106) 5351620150

C25i 3,1 (6.86) 4250 (150) 5351630150

* Removable throttle.


Pneumatic pilot port, Solenoid pilot valve, Silencers, Flanges, Pressure gauges: see Accessories

2

Series C4i, C15i, C25i Progressive start-up units C4i, C15i, C25ipneumatic or solenoid actuation


* CNOMO/AFNOR E49-066 mounting surface. **2 Threads M 4.

Series A B C D E F G H I J K

C4i 100 37 37 20,5 41 47 23,5 73 91,5 83 97C15i 155,5 60 60 31,5 63 63 31,5 99 152,5 142 148C25i 175 68 68 36 72 80 40 107,5 173,5 152 170

Series M N P Q R (L) G1/8 (L) G 1/4 (L) G 3/8 (L) G 1/2 (L) G 3/4 (L) G1

C4i 4,2 27 42,5 G 1/4 10 94 99 99 – – –C15i 5,1 39,1 64 G 1/2 18 – 141 152 152 – –C25i 6,3 40 75 G 1/2 21 – – 165 172 172 193

Series C4i, C15i, C25i Sequencing and balancing valve, C4i and C25i

1

Technical Data

Type Poppet valve, spring-loaded, switchableSupply pressure range 1 to 12 bar (15 to 174 psi),

Threshold pressure (adjustable)1....8 bar (15 .. 116 psi)

Nominal flow Qnat 6 bar (87 psi), ∆p = 1 bar (15 psi) See tableAmbient temperature range +5 °C to +50 °C (+41 °F to +122 °F)



N.B.: After setting the required pressure level the adjusting knob can be wire-locked and lead-sealed.

Technical information

Sequencing valve (supply at port 1).- Supply pressure at port 1 builds up.- Check valve blocks air passage to port 2.- When the pressure at port 1 exceeds the threshold pressure, determined by the spring setting, the valve switches and air flows to port 2.Balancing valve (supply at port 2).- Supply pressure at port 2 builds up.- Air flows via the check valve to port 1.- Delivery pressure builds up.- When the pressure at port 1 exceeds the threshold pressure determined by the spring setting, the valve switches. The air flows via the two circuits to port 1.- If the supply pressure at port 2 drops and if the delivery pressure drops to a level below the threshold pressure, the valve switches and the preset pressure in the system is maintained.

Part no.


Part no.without flange

C4i 0,2 (0.44) 1300 (46) 5351600300

C25i 0,9 (1.98) 5100 (180) 5351630300


Flanges see Accessories.

Series A B C D E F G H I K L M J(G1/8)

J(G 1/4)

J(G 3/8)

J(G 1/2)

J(G 3/4)

J(G 1)

C4i 91,5 37 20,5 41 47 23,5 68 46 60 4,2 27 42,5 57 62 62 – – -C25i 173,5 68 36 72 80 40 133,5 84 102 6,3 40 73 – – 97 104 104 125

Series C4i, C15i, C25i Oil remover and silencer C25i, G 1/2 (Purquiet)

1

Technical Data

Type Oil filter with silencerMulti-air connection 2 x threaded ports G 1/2

5 x connnections for tubes withext. dia. 10 mm in diaphragm cover

Max. supply pressure 12 bar (174 psi)Nominal flow Qnat 6 bar (87 psi) and ∆p=1 bar (15 psi) 1500 l/min (53 SCFM)Ambient temperature range +5 °C to +50 °C (+41 °F to +122 °F)


Materials Body Zn-diecastingUseful capacity 25 cl (8.5 U.S.Fl.oz)

Technical informationBores for tube connection by piercing the upper diaphragm.Function :- With this oil remover and silencer all the exhaust air in the system can be collected and replaced with clean, non-lubricated air (oil filtering up to 99%), which is then released into the atmosphere.- Simultaneous silencing of up to 30 dB (A) is also achieved.- The differential pressure gauge supplied shows the pressure head (level of pressure head corresponds to degree of clogging in the cartridge).

Part no.

Symbol With differential pressure gauge and threaded ports G 1/2 ISO 228/1

5351634900

* Diaphragm for inserting pipe.** Differential pressure gauge.*** Manual drain.

Series C4i, C15i, C25i Metal bowl with sight glass series C25i

1

Technical Data

Visibility 65% of height of bowlMax. primary pressure 12 bar (174 psi)

Materials Bowl AluminumSight glass Borosilicate glass

Volume 25 cl (8.5 U.S.Fl.oz)

Part no.

Series Weight [kg] (lbs) Type Part no.

C25i 0,330 (0.728) Filter - Filter regulator 5351230072*C25i 0,335 (0.739) Lubricator 5351530032

* This part no. corresponds to the standard version supplied with semi-automatic drain. Manual or automatic drain quoted on request.

Bowl for L (lubricator) Bowl for F and FR units


Series C4i, C15i, C25i Combination Isolating Valve+FR unitSeries C4i G 1/8, G 1/4, G 3/8Security series

1

Technical Data

Type Ball valve, diaphragm filter-regulator,self-relieving with sintered filter andsemi-automatic or automatic drain (optional)


0 °C to +50 °C (+32 °F to +122 °F) with dry airMedium Compressed air


Bowl capacity 4 cl (1.35 U.S.Fl.oz)Filter porosity 25 µm or 5 µm

Technical informationThis air preparation unit, which includes a lockable isolating valve as well as a filter-regulator is aimed at helping designers meet machinery safety standards in accordance with European Directives.

Part no.

Threaded port ISO 228/1 Options Flow[l/min] (SCFM)

Part no.without pressure gauge

Without flange Standard – 5351802000Without flange Automatic drain – 5351802010Without flange Filter 5 µm – 5351802020

G 1/8 Standard 700 (25) 5351802030G 1/8 Automatic drain 700 (25) 5351802040G 1/8 Filter 5 µm 700 (25) 5351802050




Gauges, Flanges (only for units without flange) and Silencers: see Accessories

Thread ports ISO 228/1 A

G 1/8 95G 1/4 99G 3/8 99

Series C4i, C15i, C25i Combination Isolating Valve+FR unitSeries C15i G 1/4, G 3/8, G 1/2Security series

1

Technical Data







Part no.










G 1/4 95G 3/8 99G 1/2 99

Series C4i, C15i, C25i Combination Isolating Valve+FR unitSeries C25i G 3/8, G 1/2, G 3/4, G 1Security series

1

Technical Data







Part no.

Threaded port ISO 228/1 Options Flow[l/min.] (SCFM)






G 1 Standard 4300 (152) 5351832240G 1 Automatic drain 4300 (152) 5351832250G 1 Filter 5 µm 4300 (152) 5351832260



2

Series C4i, C15i, C25i Combination Isolating Valve+FR unitSeries C25i G 3/8, G 1/2, G 3/4, G 1Security series


G 3/8 165G 1/2 172G 3/4 172G 1 193

Series C4i, C15i, C25i Combination Isolating Valve+FR+Emergency Stop Valve UnitSeries C4i G 1/8, G 1/4, G 3/8Security series

1

Technical Data

Type Ball valve, diaphragm filter-regulator,self-relieving with sintered filter andsemi-automatic or automatic drain (optional)and poppet valve



Materials Body Zn-diecastingBowl Polyamide - with composite bowl guardSeals Nitrile rubber


Technical informationThis air preparation unit, which includes a lockable isolating valve as well as a filter-regulator and emergency stop valve is aimed at helping designers meet machinery safety standards in accordance with European Directives.

Part no.








Gauges, Flanges (only for units without flange), Pneumatic pilot port, Solenoid pilot valve and Silencers: see Accessories

2


* CNOMO / AFNOR E-49-066 interface for pilot.


G 1/8 132G 1/4 136G 3/8 136


1

Technical Data




Materials Body Zn-diecastingBowl Polyamide - with metal bowl guardSeals Nitrile rubber



Part no.









2




G 1/4 204G 3/8 212G 1/2 212

Series C4i, C15i, C25i Combination Isolating Valve+FR+Emergency Stop Valve UnitSeries C25i G 3/8, G 1/2, G 3/4, G 1Security series

1

Technical Data


Wire color pink-brown brown-redMax. supply pressure 12 bar (174 psi)Secondary pressure 0,5–10 bar (7–145 psi)Nominal flow Qn at primary pressure =7 bar (102 psi);secondary pressure = 6 bar (87 psi) and See table∆p=1 bar (15 psi)Ambient temperature range +5 °C to +50 °C (+41 °F to +122 °F)

0 °C to +50 °C (+32 °F to +122 °F) with dry airMedium Compressed airValveposition 1 1


Bowl capacity 25 cl (8.5 U.S.Fl.oz)Pin c1 b1Filter porosity 25 µm or 5 µm

40-wire connection cable, 8 to 14 valve positions$ $


Part no.










2

Series C4i, C15i, C25i Combination Isolating Valve+FR+Emergency Stop Valve UnitSeries C25i G 3/8, G 1/2, G 3/4, G 1Security series



G 3/8 204G 1/2 212G 3/4 212G 1 212

Series C4i, C15i, C25i Combination Isolating Valve+FR+Emergency Stop Valve + Adjustable Progressive Start up Valve UnitSeries C4i G1/8, G1/4, G 3/8 - Security series

1

Technical Data

Type Ball valve, diaphragm filter-regulator,self-relieving with sintered filter andsemi-automatic or automatic drain (optional),poppet valve and spring loadedadjustable valve.





Technical informationThis air preparation unit, which includes a lockable isolating valve as well as a filter-regulator, emergency stop valve and start up valve is aimed at helping designers meet machinery safety standards in accordance with European Directives.

Part no.









2

Series C4i, C15i, C25i Combination Isolating Valve+FR+Emergency Stop Valve + Adjustable Progressive Start up Valve UnitSeries C4i G1/8, G1/4, G 3/8 - Security series



G 1/8 168G 1/4 173G 3/8 173

Series C4i, C15i, C25i Combination Isolating Valve+FR+Emergency Stop Valve + Adjustable Progressive Start up Valve UnitSeries C15i G 1/4, G 3/8, G 1/2 - Security series

1

Technical Data

Type Ball valve, diaphragm filter-regulator,self-relieving with sintered filter andsemi-automatic or automatic drain (optional),poppet valve and spring loadedadjustable valve.






Part no.









2

Series C4i, C15i, C25i Combination Isolating Valve+FR+Emergency Stop Valve + Adjustable Progressive Start up Valve UnitSeries C15i G 1/4, G 3/8, G 1/2 - Security series



G 1/4 264G 3/8 272G 1/2 272

Series C4i, C15i, C25i Combination Isolating Valve+FR+Emergency Stop Valve + Adjustable Progressive Start up Valve UnitSeries C25i G 3/8, G 1/2, G 3/4, G 1 - Security series

1

Technical Data

Type Ball valve, diaphragm filter-regulator,self-relieving with sintered filter andsemi-automatic or automatic drain (optional),poppet valve and spring loadedadjustable valve






Part no.










2

Series C4i, C15i, C25i Combination Isolating Valve+FR+Emergency Stop Valve + Adjustable Progressive Start up Valve UnitSeries C25i G 3/8, G 1/2, G 3/4, G 1 - Security series



G 3/8 301G 1/2 308G 3/4 308G 1 329

Series C4i, C15i, C25i Combination Isolating Valve+FR+L UnitSeries C4i G 1/8, G 1/4, G 3/8Security series

1

Technical Data

Type Ball valve, diaphragm filter-regulator,self-relieving with sintered filter andsemi-automatic or automatic drain (optional)and proportional mist lubricator





Technical informationThis air preparation unit, which includes a lockable isolating valve as well as a filter-regulator and lubricator is aimed at helping designers meet machinery safety standards in accordance with European Directives.

Part no.









2



G 1/8 132G 1/4 136G 3/8 136


1

Technical Data






Technical informationThis air preparation unit, which includes a lockable isolating valve as well as a filter-regulator and a lubricator is aimed at helping designers meet machinery safety standards in accordance with European Directives.

Part no.









2



G 1/4 206G 3/8 212G 1/2 212

Series C4i, C15i, C25i Combination Isolating Valve+FR+L UnitSeries C25i G 3/8, G 1/2, G 3/4, G 1Security series

1

Technical Data






Technical informationThis air preparation unit, which includes a lockable isolating valve as well as a filter-regulator and a lubricator is aimed at helping designers meet machinery safety standards in accordance with European Directives.

Part no.










2

Series C4i, C15i, C25i Combination Isolating Valve+FR+L UnitSeries C25i G 3/8, G 1/2, G 3/4, G 1Security series


G 3/8 233G 1/2 240G 3/4 240G 1 261

Series C4i, C15i, C25i Combination Isolating Valve+FR+L+Emergency Stop Valve UnitSeries C4i G 1/8, G 1/4, G 3/8Security series

1

Technical Data

Type Ball valve, diaphragm filter-regulator,self-relieving with sintered filter andsemi-automatic or automatic drain (optional),proportional mist lubricator and poppet valve





Technical informationThis air preparation unit, which includes a lockable isolating valve as well as a filter-regulator, lubricator and emergency stop valve is aimed at helping designers meet machinery safety standards in accordance with European Directives.

Part no.









2




G 1/8 169G 1/4 173G 3/8 173


1

Technical Data

Type Ball valve, diaphragm filter-regulator,self-relieving with sintered filter andsemi-automatic or automatic drain (optional),proportional mist lubricator and poppet valve





Technical informationThis air preparation unit, which includes a lockable isolating valve as well as a filter-regulator, lubricator and emergency stop valve is aimed at helping designers meet machinery safety standards in accordance with European Directives.

Part no.

Threaded port ISO 228/1 Options Flow[l/mi.] (SCFM)








2




G 1/4 206G 3/8 212G 1/2 212

Series C4i, C15i, C25i Combination Isolating Valve+FR+L+Emergency Stop Valve UnitSeries C25i G 3/8, G 1/2, G 3/4, G 1Security series

1

Technical Data

Type Ball valve, diaphragm filter-regulator,self-relieving with sintered filter andsemi-automatic or automatic drain (optional),proprtional mist lubricator and poppet valve





Technical informationThis air preparation unit, which includes a lockable isolating valve as well as a filter-regulator, lubricator and emergency valve is aimed at helping designers meet machinery safety standards in accordance with European Directives.

Part no.










2

Series C4i, C15i, C25i Combination Isolating Valve+FR+L+Emergency Stop Valve UnitSeries C25i G 3/8, G 1/2, G 3/4, G 1Security series



G 3/8 301G 1/2 308G 3/4 308G 1 329

Series C4i, C15i, C25i Combination Isolating Valve+FR+L+Emergency Stop Valve + Adjustable Progressive Start up Valve UnitSeries C4i G 1/8, G 1/4, G 3/8 - Security series

1

Technical Data

Type Ball valve, diaphragm filter-regulator,self-relieving with sintered filter andsemi-automatic or automatic drain (optional),proportional mist lubricator, poppet valveand spring loaded adjustable valve.

Max. supply pressure 12 bar (174 psi)Secondary pressure 0,5–10 bar (7–145 psi)Nominal flow Qn at primary pressure =7 bar (102 psi);secondary pressure = 6 bar (87 psi) and See tableValveposition 1 1∆p=1 bar (15 psi)Ambient temperature range +5 °C to +50 °C (+41 °F to +122 °F)




Valveposition 7 7

Technical informationThis air preparation unit, which includes a lockable isolating valve as well as a filter-regulator,lubricator, emergency stop valve and progessive start up valve is aimed at helping designersmeet machinery safety standards in accordance with European Directives.

Part no.









2




G 1/8 205G 1/4 210G 3/8 210


1

Technical Data

Type Ball valve, diaphragm filter-regulator,self-relieving with sintered filter andsemi-automatic or automatic drain (optional),proportional mist lubricator, poppet valveand spring loaded adjustable valve.





Technical informationThis air preparation unit, which includes a lockable isolating valve as well as a filter-regulator, lubricator, emergency stop valve and start up valve is aimed at helping designers meet machinery safety standards in accordance with European Directives.

Part no.









2




G 1/4 324G 3/8 332G 1/2 332

Series C4i, C15i, C25i Combination Isolating Valve+FR+L+Emergency Stop Valve + Adjustable Progressive Start up Valve UnitSeries C25i G3/8, G1/2, G 3/4, G 1 - Security series

1

Technical Data

Type Ball valve, diaphragm filter-regulator,self-relieving with sintered filter andsemi-automatic or automatic drain (optional),proportional mist lubricator, poppet valveand spring loaded adjustable valve





Technical informationThis air preparation unit, which includes a lockable isolating valve as well as a filter-regulator, lubricator, emergency stop valve and start up valve is aimed at helping designers meet machinery safety standards in accordance with European Directives.

Part no.












G 3/8 369G 1/2 376G 3/4 376G 1 397

Series C4i, C15i, C25i Combination Isolating Valve+F+R+L UnitSeries C4i G 1/8, G 1/4, G 3/8Security series

1

Technical Data

Type Ball valve, filter with semi-automatic drain(manual or automatic drain as option),diaphragm regulatorand proportional mist lubricator




Oil viscosity 9–11 mm²/s


Technical informationThis air preparation unit, which includes a lockable isolating valve as well as a filter, regulator and lubricator is aimed at helping designers meet machinery safety standards in accordance with European Directives.

Part no.









2



G 1/8 169G 1/4 173G 3/8 173


1

Technical Data

Type Ball valve, filter with semi-automatic drain(manual or automatic drain as option),diaphragm regulatorand proportional mist lubricator


0 °C to +50 °C (+32 °F to +122 °F) with dry airMedium Compressed airOil viscosity 9–11 mm²/s




Part no.









2



G 1/4 266G 3/8 272G 1/2 272

Series C4i, C15i, C25i Combination Isolating Valve+F+R+L UnitSeries C25i G 3/8, G 1/2, G 3/4, G 1Security series

1

Technical Data

Type Ball valve, filter with semi-automatic drain(manual or automatic drain as option)diaphragm regulatorand proportional mist lubricator

Max. supply pressure 12 bar (174 psi)Secondary pressure 0,5–10 bar (7–145 psi)Nominal flow Qn at primary pressure =7 bar (102 psi);secondary pressure = 6 bar (87 psi) and See table∆p=1 bar (15 psi)Connecting nipple G 1/8, G 1/4 (adapter for pressure gauges Ø 40, G 1/8), 1823391388Ambient temperature range +5 °C to +50 °C (+41 °F to +122 °F)

0 °C to +50 °C (+32 °F to +122 °F) with dry airMedium Compressed airOil viscosity 9–11 mm²/s




Part no.










2

Series C4i, C15i, C25i Combination Isolating Valve+F+R+L UnitSeries C25i G 3/8, G 1/2, G 3/4, G 1Security series


G 3/8 301G 1/2 308G 3/4 308G 1 329

Series C4i, C15i, C25i Combination Isolating Valve+F+R+L+Emergency Stop Valve UnitSeries C4i G 1/8, G 1/4, G 3/8Security series

1

Technical Data

Type Ball valve, filter with semi-automatic drain(manual or automatic drain as option)diaphragm regulator, proportionalmist lubricator and poppet valve


0 °C to +50 °C (+32 °F to +122 °F) with dry airMedium Compressed airOil viscosity 9–11mm²/s



Technical informationThis air preparation unit, which includes a lockable isolating valve as well as a filter, regulator, lubricator and emergency stop valve is aimed at helping designers meet machinery safety standards in accordance with European Directives.

Part no.









2




G 1/8 206G 1/4 210G 3/8 210


1

Technical Data






Technical informationThis air preparation unit, which includes a lockable isolating valve as well as a filter, regulator, lubricator and emergency stop valve is aimed at helping designers meet machinery safety standards in accordance with European Directives.

Part no.









2




G 1/4 326G 3/8 332G 1/2 332

Series C4i, C15i, C25i Combination Isolating Valve+F+R+L+Emergency Stop Valve UnitSeries C25i G 3/8, G 1/2, G 3/4, G 1Security series

1

Technical Data


Max. supply pressure 12 bar (174 psi)Secondary pressure 0,5–10 bar (7–145 psi)Nominal flow Qn at primary pressure =7 bar (102 psi);secondary pressure = 6 bar (87 psi) and∆p=1 bar (15 psi) See tableAmbient temperature range +5 °C to +50 °C (+41 °F to +122 °F)




Technical informationThis air preparation unit, which includes a lockable isolating valve as well as a filter, regulator, lubricator and emergency valve is aimed at helping designers meet machinery safety standards in accordance with European Directives.

Part no.










2

Series C4i, C15i, C25i Combination Isolating Valve+F+R+L+Emergency Stop Valve UnitSeries C25i G 3/8, G 1/2, G 3/4, G 1Security series



G 3/8 369G 1/2 376G 3/4 376G 1 397

Series C4i, C15i, C25i Accessories for modular Ci and Ecoline series

1

Flanges with threaded ports (in pairs) and flanges with push-in connectors

Series Part no.G1/8

Part no.G 1/4

Part no.G 3/8

Part no.G 1/2

Part no.G 3/4

Part no.G 1

C4i 5351006002 5351006012 5351006022 – – –C15i – 5351026002 5351026012 5351026022 – –C25i – – 5351036002 5351036012 5351036022 5351036032

Materials: Zn-diecasting for G 1/8 to G 3/4, aluminum for G 1.

Series Part no.Tube

8 mm dia.

Part no.Tube

10 mm dia.

Part no.Tube

12 mm dia.

Part no.tube

Ø 14 mm

H G Ø 8 H G Ø 10 H G Ø 12 H G Ø 14

C4i 5351006082 5351006092 – – 22,5 27,5 – –C15i – – 5351026082 5351026092 – – 25,5 27,5C25i – – – – – – – –

Materials: Zn-diecasting - thermoplastic - Screws galvanized steel - Seals nitrile.

Series Part no.NPT 1/8

Part no.NPT 1/4

Part no.NPT 3/8

Part no.NPT 1/2

Part no.NPT 3/4

Part no.NPT 1

C4i 8901700002 8901700012 8901700022 – – –C15i – 8901700032 8901700042 8901700052 – –C25i – – 8901700062 8901700092 8901700072 8901700082

Series A B C D E F G I J K HG1/8

HG 1/4

HG 3/8

HG 1/2

HG 3/4

HG 1

C4i 44 22 18,5 37 40,5 5 11,5 4,2 27 4,5 10 12,5 12,5 – – –C15i 60 30 30,5 61,5 64 7 14 5,1 39,1 11 – 12 16 16 – –C25i 72 36 34 68 71 8,5 17 6,3 40 8 – – 14,5 18 18 28,5

1

Threaded ring

Series Part no. D S M

C4i and Ecoline 5351004304 35 4 M 30 x 1,5C15i 5351024304 54 5 M 45 x 2C25i 5351034304 64 6 M 52 x 2

Material: Aluminum.

1

Mounting bracket

Series Part no. A B C D E F

C4i and Ecoline 5351000504 41 65 42 30 19 11,5C15i 5351020504 58 62 40 42,5 30 16C25i – – – – – – –

Material: Galvanized sheet steel.

1

Silencer, sintered bronze, with thread

Part no. G to ISO228/1

NV Ø D[mm]

L1 L2 Weight[kg] (lbs)

Sound pressure level to DIN 45 635

Reduction in flow %

5324000060 M 5 7 2,5 15 5 0,004 (0.009)

65 –

8140000700 M 7 Ø 10 4 15 5 0,006 (0.013)

70 –

5324011100 G 1/8 13 6 18 6 0,010 (0.022)

75 6

5324011110 G 1/4 17 8,5 25 8 0,020 (0.044)

80 22

5324011120 G 3/8 22 12 34 10 0,050 (0.110)

85 41

5324011130 G 1/2 27 14,5 44 12 0,080 (0.176)

85 18

5324011140 G 3/4 32 19 66 14 0,130 (0.287)

85 20

5324011150 G 1 41 25 66 16 0,180 (0.397)

90 22

Materials; Sintered bronze, thread in brass.Working pressure p max.: 10 bar. (145 psi)Ambient temperature range: –25 °C to +80 °C (–13 °F to 176 °F).

1

Silencer, porous polyethene, with thread

Part no. G to ISO 228/1 L1 L2 Ø D [mm] Sound pressure level to DIN 45 635

Reduction in flow %

4381000000 M 5 17 4,5 6,5 55 3,54381100000 G 1/8 24 5 13 69 14381200000 G 1/4 31 7 17 68 8,5

4381250000 G 3/8 53 11 19 69 274381300000 G 1/2 53 11 26,5 68 174381400000 G 3/4 113 16,5 38 72 31

4381500000 G 1 136 20 49 76 18Materials; PP, PE porous.Working pressure p max.: 10 bar. (145 psi)Ambient temperature range: –25 °C to +50 °C (–13 °F to 122 °F).

1

Self-cleaning silencer

Thread ISO 228/1 Part no.G 1/8 8901702890G 1/4 8901702900

G 3/8 8901702910G 1/2 8901702920G 3/4 8901702930

G 1 8901702940

1

Diverting module (1 port) - Series C4i and C25i

Series Part no. * A B C D E F G H I J L M

C4i 5351002302 60 37 20,5 41 47 23,5 32 42,5 46 60 4,2 27C15i – – – – – – – – – – – – –C25i 5351032302 97 68 36 72 80 40 49 73 84 102 6,3 40

For connection of a third module at 90°. Important: The filter and lubricator must be mounted vertically.* Without flange - Materials: Body, Zn-diecasting - Screws, galvanized steel.

K G1/8 G 1/4 G 3/8 G 1/2 G 3/4 G 1

C4i 57 62 62C15i – – – – – –C25i 97 104 104 125

1

Pneumatic pilot port G 1/4

Series Part no.

C4i 5351602302C15i 5351602302C25i 5351602302

Material: Aluminum.For emergency stop valves, piloted progressive start-up valves and progressive start-up units.

1

Locking system with key

Series Part no.

C4i 5351005302C15i 5351005302C25i 5351005302

For pressure regulators and filter regulators with control knob.Materials: Brass - thermoplastic.

1

Connecting flange for assembly of two units

Series Part no.C4i 5351006072C15i 5351026072

C25i 5351036072

Materials: Zn-diecasting - thermoplastic - screws: galvanized steel - seals: nitrile.

1

Clip for fixing into DIN rail

Series Fig. Part no.C4i 1 5351003502 ¹)C15i 2 5351023502 ²)

¹) - Set of 2 clips for an air processing unit.

²) - Set of 4 clips for an air processing unit.

For fixing an air processing unit onto a DIN rail EN 50022

Material: Spring steel.

1

Support bracket (to be used when more than 3 modules in an assembly)

Series Part no.

C4i –

C15i –C25i 3595828508

Material: Stainless steel.

1

Extra accessories for flanges (Series C 15i only) - Plug

Series Part no.C4i –C15i 5351020404

C25i –

Material: Thermoplastic.

1

Extra accessories for flanges (Series C15i only) - Connection G1/8


C25i –

Material: Brass.

1

Extra accessories for flanges (series C15i only) - Push-in connector 6 mm dia.


C25i –

Materials: Brass - seals nitrile.

1

Ecoclip (for mounting an Ecoline unit)

Series Part no.Ecoline 5351701004

Material: Thermoplastic.

1

Air inlet C4i (2 ports)

Threaded ports ISO 228/1 A Part no.

G 1/8 57G 1/4 62 5351002312G 3/8 62

1



G 1/4 54G 3/8 62 5351022302G 1/2 62

1



G 3/8 59G 1/2 66 5351032312G 3/4 66G 1 87

1

Automatic drain

Series Part no.C4i 8901700102

C15i, C25i 8901700142

¹) Series C15i and C25i.²) Series C4i.

Series C4i, C15i, C25i CAD library

1

Technical Characteristics

A library of products designed for the preparation of compressed air and in particular of "FRL modules" sizes C4i, C15i, C25i.This system, consisting of "dwg" indexes, is compatible with AutoCAD 10 and later versions. This library uses the processes described in Autolisp and requires at 640 kB memory.It consists of three 3"1/2 diskettes and a manual. The menus and the manual are written in three languages "English, German, French".

It is possible for the user of AutoCAD LT to use the AutoCAD processes to insert the blocks representing the different products. A ".txt" index gives the list of indexes representing the different products in the function of the selected menu.

Part no: 2851105351

The drawings of the air treatment products are also contained in the general library 2D.This library is presented on CD-ROM and usable with AUTOCAD starting version 12 and AUTOCAD LT version 3 and 97. This library on CD-ROM contains also the files in DXF format.

Part no.: 2851100060

Bosch Rexroth AGPneumaticsUlmer Straße 4DE-30880 LaatzenDeutschlandTel. +49 (0)511-21 36-0Fax. +49 (0)511-21 [email protected]

Bosch Rexroth Pty. Ltd.Pneumatics23 Iverseb TerraceChristchurchNew ZealandTel. +64 (0011) 643 365 9591Fax. +64 (0011) 643 358 9703

Bosch Rexroth LimitedPneumaticsBroadway Lane, South Cerney,CirencesterGloucestershire GL7 5UHGreat BritainPhone: +44-12 85-863 000Fax: +44-12 85-863 [email protected]

Bosch Rexroth CorporationPneumatics1953 Mercer roadLexington, KY 40511-1021USAPhone: +1-859-254 80 31Fax: +1-859-254 41 [email protected]

Bosch Rexroth Canada Corp.Pneumatics3426 Mainway DriveBurlington, Ontario L7M 1A8CanadaTel: +1 905-335-5511Fax. +1 905 [email protected]

Bosch Rexroth Pty. Ltd.Head Office3 Valediction RoadKings Park NSW 2148, SydneyAustraliaTel. +61 (2) 9831-7788Fax. +61 (2) [email protected]

2006-03-07

© This document, as well as the data,specifications and other informations set forth in it, are the exclusive prop-erty of Bosch Rexroth AG. Without their consent it may not be reproduced

Documents

Series C4i, C15i, C25i - Bosch Rexrothw1.boschrexroth.se/pdf/CATALOG_83_275_800.pdf · Series C4i, C15i, C25i Ordering key for single FRL modules or manifolded FRL units 1 How to