Upload
others
View
7
Download
0
Embed Size (px)
Citation preview
GEAR CASE - Made of high strength cast iron. Completely sealed for oil enclosed operation and tokeep dirt out.
WORM SHAFT - One piece alloy steel hardened and ground for extra durability. Compact design allowshydraulic motor to be coupled directly to worm.
WORM GEAR - High tensile aluminum-nickel alloy bronze. Optimum lead and pressure angles transmitmaximum power to the drum.
GEAR RATIO - 20:1 standard, 10:1, 27:1, 40:1 optional ratios provide optimum efficiency in power andspeed.
BEARINGS - Worm gear and worm shaft run on tapered roller bearings. Outer end housing hassealed ball bearing.
DRUM SHAFT - 1-1/2” diameter heat -treated alloy steel minimum tensile strength 150,000 psi.
CABLE DRUM - Tough all steel construction resists breakage or warping.
“Quality Since 1910”
UP TO 12,000 POUNDS CAPACITY
RV7/2001
CAUTION:This winch model does not include any kind of holding brake. If your applicationrequires a holding brake choose Lift-Safe® winch series LS10H Vanging wincheswith automatic hydraulic safety brakes.
BloomTM Hydraulic Cable Winches – Standard Features
Series 1000 Vanging - Split DrumHYDRAULIC CABLE WINCHESThe rugged construction and versatility of Series 1000 Vanging - split drum winches make it adaptable to a wide range of applications. Series 1000 Vanging - split drum direct drive winches are used for pulling, dragging applications on fishing boats and marine craft where two cables are required.
MODEL EXAMPLE: 10-E-L8-20-5118
Drum SizeL8 (5118 split drum) With 4" Core
Hydraulic Motor Designation A, B, C, DD, E, G,
4.9, 6.2, 8.0, 9.6, 11.9
Gear Case andShaft Designation
10 = Series 1000 Vanging with 1-1/2” Drum Shaft
Gear Ratio10:1, 20:1, 27:1, 40:1
Series 1000 Vanging - Split DrumModel Selection from Performance Data “Quality Since
1910”
1/2
4080
1/4 5/16 3/8 7/16
55120190
CABLE DIAMETER (IN.)
DRUM "L8" (5118) CAPACITY (FT.)
DRUM CAPACITY PER SIDE OF SPLIT DRUM
Series 1000 Vanging - Split Drum“Quality Since
1910” Model Selection from Performance Data
OIL PRESSURE (LBS./SQ.IN.)1000
4000
0
2000
500
6000
8000
10000
CA
BLE
SPE
ED 1
ST
25001500 2000 3000OIL FLOW (GALLONS/MIN.)
10:1 RATIO (optional)
10
100 5 2515 20
30
50
70
90
110
20:1 RATIO (standard)
1000
2000
0
6000
8000
4000
500
10000
25001500 2000 3000 0
10
5 10 15 20 25
27:1 RATIO (optional)
10000 500
12000
25001500 2000 3000 0 5 10 15 20 25
40:1 RATIO (optional)
1000
2000
0
6000
8000
4000
500
10000
25001500 2000 3000 0
10
5 10 15 20 25
TOTA
L PU
LL 1
ST L
AYE
R
OF
CA
BLE
(LB
S.)
LAYE
R (F
T./M
IN.)
OIL PRESSURE (LBS./SQ.IN.)
LAYE
R (F
T./M
IN.)
CA
BLE
SPE
ED 1
ST
OIL FLOW (GALLONS/MIN.)
OIL PRESSURE (LBS./SQ.IN.)
LAYE
R (F
T./M
IN.)
CA
BLE
SPE
ED 1
ST
OIL FLOW (GALLONS/MIN.)
OIL PRESSURE (LBS./SQ.IN.)
LAYE
R (F
T./M
IN.)
CA
BLE
SPE
ED 1
ST
OIL FLOW (GALLONS/MIN.)
20
30
40
50
60
10000
2000
4000
6000
8000
40
30
20
10
20
30
11.9 9.6
8.06.24.9
A
11.99.6
8.0
6.24.9A
11.9 9.68.0 6.2
4.9
A
A4.9 6.2
8.09.6
11.9
11.9
9.68.0 6.2
4.9
A
A4.9 6.2
8.09.6
11.9
A
4.96.28.0 A
4.9 6.28.0
GE
BCDD
B CDD
EG
BC
DDE
GB
C DDE
G
BC
DDE
G B CDD
G
BC
DDEBC DD
E
TOTA
L PU
LL 1
ST L
AYE
R
OF
CA
BLE
(LB
S.)
TOTA
L PU
LL 1
ST L
AYE
R
OF
CA
BLE
(LB
S.)
TOTA
L PU
LL 1
ST L
AYE
R
OF
CA
BLE
(LB
S.)
“Quality Since 1910”
“Quality Since 1910” Series 1000 Vanging
With L8 (5118) Split Drum Base Mount Model - Direct Drive
WARNING!Goods are not intended for use in the moving or lifting of
persons!
The winches described herein are neither designed nor intendedfor use or application to equipment used in the lifting or moving of persons and it is understood that all such use shall be at the sole risk of the user.
The cable clamps on winches are not designed to hold rated loads. A minimum of 5 wraps of cable must be left on drum barrel to guarantee holding of rated load.
Applications of winch where life would be endangered by any event are not recommended.
Correct choice of Directional Control Valves for Bloom Winches
Tandem Center Spool Valve – Work Ports are blocked in neutral position
Use on all winches that use motor only to hold load.
*Winches require ridged mounting plate.See owner’s manual for information about proper mounting
plate thickness or call Bloom Sales Engineer at factory
Winch Division1443 220th Street,, Independence, Iowa 50644
FAX 319-827-1140 PHONE 319-827-1139
BLOOM Manufacturing Inc.
www.bloommfg.com©Copyright 2015 Bloom Mfg. Inc.