Sensor-Based Intelligent Mobile Robot Navigation in ... · 1 Abstract – This paper presents sensor-based intelligent mobile robot navigation in unknown environments. The paper deals

1

Abstract – This paper presents sensor-based intelligent mobile robot navigation in unknown environments. The paper deals with fuzzy control of autonomous mobile robot motion in an unknown environment with obstacles and gives a wireless sensor-based remote control of mobile robots motion in an unknown environment with obstacles using the Sun SPOT technology. Simulation results show the effectiveness and the validity of the obstacle avoidance behavior in an unknown environment and velocity control of a wheeled mobile robot motion of the proposed fuzzy control strategy. The proposed remote method has been implemented on the autonomous mobile robot Khepera that is equipped with sensors and the free range Spot from the Sun Spot technology. Finally, the effectiveness and the efficiency of the proposed sensor-based remote control strategy are demonstrated by experimental studies and good experimental results of the obstacle avoidance behavior in unknown environments.

Sensor-Based Intelligent Mobile Robot Navigation in Unknown Environments

Gyula MesterUniversity of Szeged, Department of InformaticsRobotics LaboratoryH 6720, Árpád tér 2, Szeged, Hungarye-mail: [email protected]

Aleksandar Rodić University of Belgrade, Mihajlo Pupin Institute Robotics LaboratoryVolgina 15, 11060 Belgrade, Serbiae-mail: [email protected]

Keywords – fuzzy control, mobile robot, navigation, wireless sensor network

1. INTRODUCTION

Many researches in robotics are currently dealing with different problems of motion of autonomous wheeled mobile robots and motion control of auton-omous wheeled mobile robots in unknown environ-ments. In recent years, autonomous wheeled mobile robots have been required to navigate in more com-plex domains, where the environment is unknown.

This paper deals with fuzzy control of autonomous wheeled mobile robot motion in an unknown environ-ment with obstacles and gives a wireless sensor-based remote control of autonomous wheeled mobile robots motion in an unknown environment with obstacles us-ing the Sun SPOT technology.

Paper [1] presents a control method for the forma-tion on nonholomic mobile robots. Robots track de-sired trajectories in the environment with static con-vex-shaped obstacles. The algorithm includes collision-avoidance between robots and obstacles. Fuzzy logic approaches to mobile robot navigation and obstacle avoidance have been investigated by several research-ers. Many application works of fuzzy logic in the mobile robot field have given promising results.

Fuzzy reactive control of a mobile robot incorporat-ing a real/virtual target switching strategy has been made in [2].

Navigation control of the robot is realized through fuzzy coordination of all the rules. Sensed ranging and relative target position signals are input to the fuzzy controller.

Real-time fuzzy reactive control is investigated for automatic navigation of an intelligent mobile robot in unknown and changing environments. A reactive rule base governing the robot behavior is synthesized cor-responding to the various situations defined by instant mobile robot motion, environment and target informa-tion.

Paper [3] presents a strategy for autonomous naviga-tion of field mobile robots on hazardous natural terrain using a fuzzy logic approach and a novel measure of terrain traversability. The navigation strategy is com-prised of three simple, independent behaviors: seek-goal, traverse-terrain, and avoid obstacles.

This navigation strategy requires no a priori informa-tion about the environment.

Preliminary Communication

Volume 1, Number 2, December 2010

20 mm

(Style: Ariel Bold, 22pt)

(Style: Ariel Bold, 12pt)(Style: Ariel Regular, 10pt)

(Style: Ariel Italic, 9pt)

(Style: Ariel Italic, 9pt)

80 mm 80 mm5 mm

20 mm 25 mm


(Style: Ariel Regular, 10pt)

Tab: 3mm

25 mm

2

The sensor-based navigation of a mobile robot in in-door environment is very well presented in [4].

The paper deals with the problem of navigation of a mobile robot either in an unknown indoor environ-ment or in a partially known one. Fuzzy controllers are created for navigation of the real robot. Good results obtained illustrate the robustness of a fuzzy logic ap-proach with regard to sensor imperfections.

Design, stability analysis and implementation of new intelligent fuzzy control systems for perception and navigation of nonholonomic autonomous mobile robots have been made in [5]. Reactive, planned and teleoperated techniques are considered.

Paper [6] proposed the use of a single side reflex for autonomous navigation of mobile robots in unknown environments. In this work, fuzzy logic based imple-mentation of the single-sided reflex is considered. The use of perceptional symmetry allows perception–ac-tion mapping with reduced sensor space dimensions. Simulation and experimental results are presented to show the effectiveness of the proposed strategy in typ-ical obstacle situations.

The model of an autonomous wheeled mobile robot has two driving wheels and the angular velocities of the two wheels are controlled independently.

Fuzzy control of an autonomous wheeled mobile ro-bot motion in unknown environments with obstacles is proposed. Outputs of the fuzzy controller are the angu-lar speed difference between the left and right wheels of the vehicle and the vehicle velocity. Simulation re-sults show the effectiveness and the validity of the ob-stacle avoidance behavior in an unknown environment and velocity control of a wheeled mobile robot motion of the proposed fuzzy control strategy.

Wireless sensor-based remote control of mobile ro-bots motion in unknown environments using the Sun SPOT technology is proposed. The proposed method has been implemented on the miniature autonomous mobile robot Khepera that is equipped with sensors and the free range Spot from the Sun Spot technology.

Finally, the effectiveness and the efficiency of the proposed sensor-based remote control strategy are demonstrated by experimental studies and good ex-perimental results of the obstacle avoidance behavior in unknown environments.

The paper is organized as follows:

Section 1 gives Introduction. The model of the au-tonomous wheeled mobile robot is given in Section 2. Section 3 illustrates environment perception. In Sec-tion 4, a strategy of autonomous wheeled mobile robot motion control in unknown environments is proposed. Section 5 illustrates a wireless sensor network (WSN). In Section 6 Sun-SPOT-based remote control of wheeled mobile robots is proposed. Conclusions are given in Section 7.

2. MODEL OF THE AUTONOMOUS WHEELED MOBILE ROBOT

In this paper, the model of the autonomous wheeled mobile robot has two driving wheels (which are at-tached to both sides of the vehicle) and the angular velocities:

, rl~ ~ (1)

of the two wheels are controlled independently (Fig. 1).

Fig. 1. Model of a differentially driven autonomous wheeled mobile robot in the two-dimensional

work space

[ ]Tlr ,,,y,xq ϕϕθ= (2)

The contact between the wheel of autonomous mo-bile robots and a non-deformable horizontal plane supposes both the conditions of pure rolling and non-slipping during the motion. This means that the veloc-ity of the contact point between each wheel and the horizontal plane is equal to zero.

The rotation angle of the wheel about its horizontal axle and the radius of the wheel are denoted by φ(t) and R, respectively.

Hence, the position of the wheel is characterized by 2 constants:

2b – the distance between wheels, R wheel radius,and its motion by a time-varying angle: φr(t) – the rotation angle of the right wheel, and φl(t) – the rotation angle of the left wheel.

Configuration of the mobile robot can be described by five generalized coordinates such as:

where:

x and y are the two coordinates of the center of mass C – robot position (the geometric center of the autono-mous wheeled mobile robot),

International Journal of Electrical and Computer Engineering Systems



3

ωω

−

=

θ l

r

b2/Rb2/R2/R2/Rv

(3)

θ is the orientation angle of the autonomous wheeled mobile robot (robot orientation).

A kinematic model of the velocity v and the angular ve-locity θ of the mobile robot are given by the equation:

3. ENVIRONMENT PERCEPTION

The autonomous wheeled mobile robot must be ca-pable of sensing its environment. Every autonomous wheeled mobile robot needs some sensing devices first to get perception of its environment and then to move in this environment [5]. It is really important to have fast distance measurement from the mobile robot to the surrounding obstacles [14].

Conventionally, autonomous wheeled mobile ro-bots are equipped with ultrasonic sensors. It is sup-posed that the autonomous wheeled mobile robot has groups of ultrasonic sensors to detect obstacles in the front, to the right and to the left of the mobile robot. An imprecise perception of ultrasonic sensors is a result of the fact that these sensors provide a relatively accurate measurement of the distance to an object, but poor in-formation about its exact location due to angular reso-lution. Another source of uncertainty is a consequence of specular reflection and well-known problems such as cross-talking and noise. Several procedures have been developed to overcome the disadvantages of ul-trasonic sensors [5].

4. STRATEGY OF AUTONOMOUS WHEELED MOBILE ROBOT MOTION CONTROL IN UNKNOWN ENVIRONMENTS

When the autonomous wheeled mobile robot moves towards the target and the sensors detect an obstacle, an avoiding strategy is necessary. While the autonomous wheeled mobile robot is moving, it is important to com-promise between avoiding the obstacles and moving to-wards the target position. With obstacles present in the unknown environment, the autonomous wheeled mo-bile robot reacts based on both the sensed information of the obstacles and the relative position of the target [2].

Fig. 2. The block diagram of the fuzzy inference system

In moving towards the target and avoiding obstacles, the autonomous wheeled mobile robot changes its ori-entation and velocity.

When the obstacle in an unknown environment is very close, the autonomous wheeled mobile robot slows down and rapidly changes its orientation. The navigation strategy has to come as near to the target position as possible while avoiding collision with the obstacles in an unknown environment.

Fuzzy-logic-based control is applied to navigation of the autonomous wheeled mobile robot in unknown environments with obstacles [7], [8], [9].

The intelligent mobile robot reactive behavior is for-mulated by means of fuzzy rules. Inputs to the fuzzy controller are:

- the obstacle distances p,

- the obstacle orientation θ1 (which is the angle be-tween the robot moving direction and the line con-necting the robot center with the obstacle),

- the target distances l,

- the target orientation θ2 (which is the angle be-tween the robot moving direction and the line con-necting the robot center with the target).

Outputs of the fuzzy controller are:

- the angular speed difference between the left and right wheels (wheel angular speed correction) of the vehicle: Δω= ωr - ωl , and

- the vehicle velocity V.

The obstacle orientation θ1 and the target orienta-tion θ2 are determined by the obstacle/target position and the robot position in a world coordinate system, respectively.

The obstacle orientation θ1 and the target orienta-tion θ2 are defined as positive when the obstacle/tar-get is located to the right of the robot moving direc-tion; otherwise, the obstacle orientation θ1 and the target orientation θ2 are negative.

The block diagram of the fuzzy inference system is presented in Fig. 2.

For the proposed fuzzy controller the input variables for the obstacle distances p are simply expressed using


4

two linguistic labels - Gaussian membership func-tions near and far (p Є [0, 3 m]).

The input variables for the obstacle orientation θ1 are expressed using two linguistic labels - Gaussian membership functions left and right (θ1 Є [-π, π rad]).

The input variables for the target distances l are sim-ply expressed using two linguistic labels - Gaussian membership functions near and far (l Є [0, 3 m]). The input variables for the target orientation θ2 are simply expressed using three linguistic labels - Gaussian mem-bership functions left, target direction and right (θ2 Є [-3.14, 3.14 rad]).

Fuzzy sets for the output variables the wheel angu-lar speed correction Δω= ωr - ωl (turn-right, zero and turn-left) of the autonomous wheeled mobile robot are shown in Fig. 3.

Fig. 3. Membership functions of the angular speed difference Δω

The output variables are normalized between: Δω Є [-20, 20 rad/s].

The other output variable of the fuzzy controller is ve-hicle velocity V. The output variables are normalized be-tween: Velocity Є [-10, 20 m/s]. Fuzzy sets for the output variables – Velocity (low and high) are shown in Fig. 4.

Fig. 4. Membership functions of velocity of the autonomous mobile robot

The rule-base for mobile robot fuzzy control is:

• If θ2 is right, then Δω is turn-right;

• If θ2 is left, then Δω is turn-left;

• If p is near and l is far and θ1 is left, then Δω is turn-right;

• If p is near and l is far and θ1 is right, then Δω is turn-left;

• If θ2 is target direction, then Δω is zero;

• If p is far and θ2 is target direction, then Δω is zero;

• If p is near and l is far, then velocity is low;

• If p is far and l is far, then velocity is high;

• If p is far and l is near, then velocity is low.

In the present implementation of the fuzzy controller the Center of Area method of defuzzification is used.

Control surface of the proposed fuzzy controller as a function of the inputs (target orientation and obstacle distances) is shown in Figure 5.

Fig. 5. Control surface of the fuzzy controller

Simulation experiments are commonly used for the initial system analysis and control design while the ex-perimental scalable tested system has to be used in the final phase of system evaluation and control verification.

The obtained results and control architecture can be adapted afterwards to a different application of au-tonomous wheeled mobile robots. Based on this, an important task in system development is accurate and valuable modeling of the observed system.

Now, the author applied the proposed fuzzy control-ler to the autonomous wheeled mobile robot moving in an unstructured environment with obstacles [10]. A simulation example of an autonomous wheeled mo-bile robot is presented in Fig. 6. Corresponding fuzzy control is implemented to perform tasks of obstacle and collision avoidance.

The results of the simulation regarding goal seek-ing and the obstacle avoidance mobile robot paths are shown in Fig. 6.


5

Fig. 6. Obstacle avoidance trajectory of a mobile robot

5. WIRELESS ROBOT-SENSOR NETWORK

A wireless sensor network (WSN) is a computer net-work consisting of spatially distributed autonomous devices using sensors to cooperatively monitor physi-cal or environmental conditions, such as temperature, sound, vibration, pressure, motion or pollutants, at different locations [19], [20], [21]. The development of wireless sensor networks was originally motivated by military applications such as battlefield surveillance. However, wireless sensor networks are now used in many civilian application areas, including environment and habitat monitoring, healthcare applications, home automation, and traffic control.

In addition to one or more sensors, each node in a sensor network is typically equipped with a radio trans-ceiver or other wireless communications device, a small microcontroller, and an energy source, usually a battery. The size of a single sensor node can vary from shoebox-sized nodes down to devices the size of a grain of dust. Size and cost constraints on sensor nodes result in cor-responding constraints on resources such as energy, memory, computational speed and bandwidth.

Wireless Robot-Sensor Networked systems (WR-SN) refer to multiple robots operating together in coor-dination or cooperatively with sensors, embedded computers, and human users [10]. Cooperation entails more than one entity working toward a common goal while coordination implies a relationship between en-

tities that ensures efficiency or harmony.

Communication between entities is fundamental to both cooperation and coordination and hence the central role of the networked system. Embedded com-puters and sensors are now ubiquitous in homes and factories, and increasingly wireless ad-hoc networks or plug-and-play wired networks are becoming common-place.

Robots are functioning in environments while per-forming tasks requiring them to coordinate with other robots, cooperate with humans, and act on information derived from multiple sensors. In many cases, these human users, robots and sensors are not collocated, and the coordination and communication happens through a network. Networked robots allow multiple robots and auxiliary entities to perform tasks that are well beyond the abilities of a single robot [10]. Robots can automatically couple to perform locomotion and manipulation tasks that either a single robot cannot perform, or would require a larger special-purpose ro-bot to perform. They can also coordinate to perform search and reconnaissance tasks exploiting the effi-ciency inherent in parallelism. Further, they can per-form independent tasks that need to be coordinated. Another advantage of networked robots is improved efficiency. Tasks like searching or mapping are, in prin-ciple, performed faster with an increase in the number of robots. A speed-up in manufacturing operations can be achieved by deploying multiple robots performing


6

operations in parallel, but in a coordinated fashion. Perhaps the greatest advantage of using the network to connect robots is the ability to connect and harness physically-removed assets.

Mobile robots can react to information sensed by other mobile robots in the next room. Human users can use machines remotely located via the network. The ability to network robots also enables fault-tolerance in design. If robots can in fact dynamically reconfigure themselves using the network, they are more tolerant to robot failures. Finally, networked robots have the po-tential to provide great synergy by bringing together components with complementary benefits and mak-ing the whole greater than the sum of the parts [10].

6. SUN SPOT BASED REMOTE CONTROL OF WHEELED MOBILE ROBOTS

In this paper Sun SPOTs (Small Programmable Object Technology) have been used to create remote control over a Khepera ® mobile robot [11].

Sun SPOT is a small electronic device made by Sun Microsystems. The Sun SPOT is designed to be a flex-ible development platform, capable of hosting widely differing application modules. The Sun SPOT connec-tion strategy [10], [11], [12], [13], [14], [15], [16], [17] is presented in Fig. 7.

Fig. 7. Remote control system

For this task 2 SunSPOTs have been used from the development kit (Sun Microsystems, Inc. 2007). Sun SPOTs are programmed in a Java programming lan-guage, with the Java VM run on the hardware itself. It has quite a powerful main processor running the Java VM “Squawk” serving as an IEEE 802.15.4 wireless net-work node. SunSPOT’s wireless protocol is a Zigbee-based protocol [14], [15], [16], [17], [18], [19], [20], [21], [22], [23], [24]. The SunSPOT base station has been used to read the data from the free range SPOT and send its contents to the PC.

The PC with a Bluetooth connection sends the con-trol signal to the mobile robot Khepera®. The miniature

mobile robot Khepera® is equipped with 9 infrared ND, 5 ultrasonic sensors and an integrated Bluetooth com-munication module. In the Robotics Laboratory , De-partment of Informatics, University of Szeged, it is pos-sible to use the sensor-based remote control system [18]. The user can start a control experiment of mobile robots in the Sun SPOT environment (Fig. 8), [11].

Fig. 8. Remote control system

7. CONCLUSION

The paper proposed wireless sensor-based remote control of mobile robots motion in unknown environ-

ments with obstacles using the Sun SPOT technology and a fuzzy reactive navigation strategy of collision-free motion and velocity control in unknown environ-ments with obstacles. The proposed method has been implemented on the autonomous mobile robot Khep-era ® that is equipped with: 9 infrared ND, 5 ultrasonic sensors and an integrated Bluetooth communication module. Wireless robot-sensor networked systems are illustrated.

Simulation results show the effectiveness and the va-lidity of the obstacle avoidance behavior in unknown environments and velocity control of a wheeled mobile robot motion of the proposed fuzzy control strategy.


7

Corresponding fuzzy control is implemented to per-form tasks of obstacle and collision avoidance.

Finally, the effectiveness and the efficiency of the proposed sensor-based remote control strategy are demonstrated by experimental studies and good ex-perimental results.

ACKNOWLEDGEMENT

The results in the paper are partially supported by the TÁMOP-4.2.2/08/1/2008-0008 program of the Hun-garian National Development Agency.

REFERENCES

[1] K. Kozlowskí, W. Kowalczik, Motion Control for Forma-tion of Mobile Robots in Environment with Obstacles, Studies in Computational Intelligence, Towards Intel-ligent Engineering and Information Technology, Vol-ume 243, 2009, Springer, pp. 203-219.

[2] W.L. Xu, S.K. Tso, Y.H. Fung: Fuzzy Reactive Control of a Mobile Robot Incorporating a Real/Virtual Target Switching Strategy, Robotics and Autono-mous Systems, Vol. 23, No. 3, 1998, pp. 171-186.

[3] H. Seraji, A. Howard, E. Tunstel, Terrain-Based Navigation of Planetary Rovers: A Fuzzy Logic Ap-proach, Proceedings of the 6th International Sym-posium on Artificial Intelligence, Robotics & Auto-mation in Space: i-SAIRAS 2001, Quebec, Canada, June 18 - 22, 2001, pp. 1-6.

[4] H. Maaref, C. Barret, Sensor Based Navigation of a Mo-bile Robot in an Indoor Environment, Robotics and Au-tonomous Systems, Vol. 38, No. 1, 2002, pp. 1–18.

[5] F. Cuesta, A. Ollero, Intelligent Mobile Robot Navi-gation, Springer, 2006.

[6] R. Chatterjee, F. Matsuno, Use of single side reflex for autonomous navigation of mobile robots in unknown environments, Robotics and Autono-mous Systems, Vol. 35, No. 2, 2001, pp. 77–96.

[7] G. Mester, Intelligent Mobile Robot Controller Design, Proceedings of the Intelligent Engineer-ing Systems Conference, London, UK, June 26-28, 2006, pp. 282-286.

[8] G. Mester, Intelligent Mobil Robot Control in Un-known Environments, Intelligent Engineering Sys-tems and Computational Cybernetics, Part I Intel-ligent Robotics, Springer, 2009, pp. 15-26.

[9] A. Rodić, D. Katić, G. Mester, Ambient Intelligent

Robot-Sensor Networks for Environmental Sur-

veillance and Remote Sensing, Proceedings of the

7th IEEE International Symposium 7th Interna-

tional Symposium on Intelligent Systems and In-

formatics, Subotica, Serbia, Sept. 25-26, 2009, pp.

39-44.

[10] A. Rodic, G. Mester, Virtual WRSN – Modeling and

Simulation of Wireless Robot-Sensor Networked

Systems. Proceedings of the 8th IEEE International

Symposium on Intelligent Systems and Informat-

ics, Sept. 10-11, Subotica, Serbia, 2010, pp. 115-

120.

[11] T. Szépe, Sensor Based Control of an Autono-

mous Wheeled Mobile Robot , Proceedings from

PROSENSE 3rd Seminar Presentations, Institute

Jožef Stefan, Ljubljana, Slovenia, 2010, pp. 34-37.

[12] T. Szépe, Robotirányítás támogatása távoli

érzékelő rendszerrel , VMTT Konferencia, Konfer-

encia-kiadvány, Újvidék, Szerbia, 2010, pp. 527-

532.

[13] Sun™ Small Programmable Object Technology

(Sun SPOT) Owner’s Manual Release 3.0, Sun Mi-

crosystems, Inc. 2007.

[14] P. Kucsera, Industrial Component-based Sample

Mobile Robot System, Acta Polytechnica Hunga-

rica, Vol. 4, No. 4, 2007, pp. 69-81.

[15] P. Kucsera, Autonomous Advertising Mobile Ro-

bot for Exhibitions, Developed at BMF, Studies in

Computational Intelligence, Towards Intelligent

Engineering and Information Technology, Vol.

243/2009, pp. 295-303.

[16] C. Pozna, V. Prahoveanu, R.E. Precup, A new pat-

tern of knowledge based on experimenting the

causal relation, Proceedings of the 14th IEEE In-

ternational Conference on Intelligent Engineering

Systems, Las Palmas, Gran Canaria Spain, May 5-7,

2010, pp. 61-66.

[17] C. Pozna, C., Precup, R-E.,Minculete, N., Antonia, C.,

Properties of Classes, Subclasses and Objects in

an Abstraction Model, Proceedings of the 19th In-

ternational Workshop on Robotics in Alpe-Adria-

Danube Region (RAAD), Budapest, Hungary, June

24-26, 2010, pp. 291-296.



Tab: 7mm

8

[18] D. Saletic, U. Popovic, Fuzzy expert system for automatic movement control of a platform on a ground with obstacles, Proceedings of the YuINFO Conference, Kopaonik, Serbia, March 6-10, 2006, pp. 1-6.

[19] I. Matijevics, J. Simon, Comparison of various wire-less sensor networks and their implementation, Proceedings of the Conference Science in Practice (SIP 2009), February 26-27, Pécs, Hungary, 2009, pp. 17-19.

[20] J. Simon, G. Martinović, I. Matijevics, WSN Imple-mentation in the Greenhouse Environment Using Mobile Measuring Station, International Journal of Electrical and Computer Engineering Systems, Vol. 1, No. 1, 2010, pp. 37-44.

[21] J. Simon, I. Matijevics, Implementation of Poten-tial Field Method for Mobile Robot Navigation in Greenhouse Environment with WSN Support, Proceedings of the IEEE Conference on Intelligent Systems and Informatics, Subotica, Serbia, Sept. 10-11, 2010, pp. 319-323.

[22] B. Kuljić, J. Simon, T. Szakáll, PathfindiBased on Edge Detection and Infrared Distance Measuring Sensor, Acta Polytechnika Hungarica, Journal of Applied Sciences, Vol. 6, No. 1, 2009, pp. 103-116.

[23] I. Matijevics, J. Simon, Control of the Greenhouse’s Microclimatic Condition using Wireless Sensor Network, IPSI Journal, TIR, Vol. 6, No. 2, 2010, pp. 35-38.

[24] J. Sárosi, J. Gyeviki, A. Véha, P. Toman, Accurate Position Control of PAM Actuator in LabVIEW En-vironment, Proceedings of the Intelligent Systems and Informatics Conference, Subotica, Serbia, September 25-26, 2009, pp. 301-305.


58 International Journal of Electrical and Computer Engineering Systems

INTERNATIONAL JOURNAL OF ELECTRICAL AND COMPUTER ENGINEERING SYSTEMS

Published by Faculty of Electrical Engineering, Josip Juraj Strossmayer University of Osijek, Croatia.

About this JournalThe International Journal of Electrical and Computer Engineering Systems publishes original research in the form of full papers, case studies, reviews and

surveys. It covers theory and application of electrical and computer engineering, synergy of computer systems and computational methods with electrical and electronic systems, as well as interdisciplinary research.

• Power systems• Renewable electricity production• Power electronics• Electrical drives• Industrial electronics• Communication systems• Advanced modulation techniques• RFID devices and systems• Signal and data processing• Image processing• Multimedia systems• Microelectronics

• Instrumentation and measurement• Control systems• Robotics• Modeling and simulation• Modern computer architectures• Computer networks• Embedded systems• High-performance computing• Parallel and distributed computer sys-

tems• Human-computer systems• Intelligent systems

• Multi-agent and holonic systems• Real-time systems• Software engineering• Internet and web applications and sys-

tems• Applications of computer systems in en-

gineering and related disciplines• Mathematical models of engineering

systems• Engineering management• Engineering education

Topics of interest include, but are not limited to:

Paper SubmissionAuthors are invited to submit original, unpublished research papers

that are not being considered by another journal or any other publish-er. Manuscripts must be submitted in doc, docx, rtf or pdf format, and limited to 30 one-column double-spaced pages. All figures and tables must be cited and placed in the body of the paper. Provide contact in-formation of all authors and designate the corresponding author who should submit the manuscript to www.etfos.hr/ijeces. The correspond-ing author is responsible for ensuring that the article’s publication has been approved by all coauthors and by the institutions of the authors if required. All enquiries concerning the publication of accepted papers should be sent to [email protected].

The following information should be included in the submission:

• paper title;• full name of each author;• full institutional mailing addresses;• e-mail addresses of each author;• abstract (should be self-contained and not exceed 150 words). In-

troduction should have no subheadings;• manuscript should contain one to five alphabetically ordered

keywords; • all abbreviations used in the manuscript should be explained by

first appearance;• all acknowledgments should be included at the end of the pa-

per:• authors are responsible for ensuring that the information in each

reference is complete and accurate. All references must be num-bered consecutively and citations of references in text should be identified using numbers in square brackets. All references should be cited within the text;

• each figure should be integrated in the text and cited in a con-secutive order. Upon acceptance of the paper, each figure should be of high quality in one of the following formats: EPS, WMF, BMP and TIFF;

• corrected proofs must be returned to the publisher within 7 days of receipt.

Peer ReviewAll manuscripts are subject to peer review and must meet aca-

demic standards. Submissions will be first considered by an editor-

in-chief and if not rejected right away, then they will be reviewed by anonymous reviewers. The submitting author will be asked to pro-vide the names of 5 proposed reviewers including their e-mail ad-dresses. The proposed reviewers should be in the research field of the manuscript. They should not be affiliated to the same institution of the manuscript author(s) and should not have had any collaboration with any of the authors during the last 3 years.

Author BenefitsThe corresponding author will be provided with a .pdf file of the

article or alternatively one hardcopy of the journal free of charge.

Units of Measurement

Units of measurement should be presented simply and concisely using System International (SI) units.

Bibliographic InformationCommenced in 2010. ISSN: 1847-6996 e-ISSN: 1847-7003

Published: semiannually

CopyrightAuthors of the International Journal of Electrical and Computer

Engineering Systems must transfer copyright to the publisher in writ-ten form.

Subscription InformationThe annual subscription rate is 50€ for individuals, 25€ for students

and 150€ for libraries.

Postal AddressInternational Journal of Electrical and Computer Engineering Sys-tems (IJECES)Faculty of Electrical Engineering Josip Juraj Strossmayer University of Osijek Kneza Trpimira 2b 31000 Osijek Croatia

59

IJECES Copyright Transfer Form

(Please, read this carefully)

This form is intended for all accepted material submitted to the IJECES journal and must accompany any such material before publication.

TITLE OF ARTICLE (hereinafter referred to as “the Work”):

COMPLETE LIST OF AUTHORS:

The undersigned hereby assigns to the IJECES all rights under copyright that may exist in and to the above Work, and any revised or expanded works submitted to the IJECES by the undersigned based on the Work. The undersigned hereby warrants that the Work is origi-nal and that he/she is the author of the complete Work and all incorporated parts of the Work. Otherwise he/she warrants that necessary permissions have been obtained for those parts of works originating from other authors or publishers.

Authors retain all proprietary rights in any process or procedure described in the Work. Authors may reproduce or authorize others to reproduce the Work or derivative works for the author’s personal use or for company use, provided that the source and the IJECES copyright notice are indicated, the copies are not used in any way that implies IJECES endorsement of a product or service of any author, and the copies themselves are not offered for sale. In the case of a Work performed under a special government contract or grant, the IJECES recognizes that the government has royalty-free permission to reproduce all or portions of the Work, and to authorize others to do so, for official government purposes only, if the contract/grant so requires. For all uses not covered previously, authors must ask for permission from the IJECES to reproduce or authorize the reproduction of the Work or material extracted from the Work. Although authors are permitted to re-use all or portions of the Work in other works, this excludes granting third-party requests for reprinting, republishing, or other types of re-use. The IJECES must handle all such third-party requests. The IJECES distributes its pub-lication by various means and media. It also abstracts and may translate its publications, and articles contained therein, for inclusion in various collections, databases and other publications. The IJECES publisher requires that the consent of the first-named author be sought as a condition to granting reprint or republication rights to others or for permitting use of a Work for promotion or marketing purposes. If you are employed and prepared the Work on a subject within the scope of your employment, the copyright in the Work belongs to your employer as a work-for-hire. In that case, the IJECES publisher assumes that when you sign this Form, you are autho-rized to do so by your employer and that your employer has consented to the transfer of copyright, to the representation and warranty of publication rights, and to all other terms and conditions of this Form. If such authorization and consent has not been given to you, an authorized representative of your employer should sign this Form as the Author.

Authors of IJECES journal articles and other material must ensure that their Work meets originality, authorship, author responsibili-ties and author misconduct requirements. It is the responsibility of the authors, not the IJECES publisher, to determine whether disclo-sure of their material requires the prior consent of other parties and, if so, to obtain it.

• The undersigned represents that he/she has the authority to make and execute this assignment.• For jointly authored Works, all joint authors should sign, or one of the authors should sign as

authorized agent for the others.• The undersigned agrees to indemnify and hold harmless the IJECES publisher from any damage or expense that may arise in

the event of a breach of any of the warranties set forth above.

__________________________________Author/Authorized Agent

__________________________________Date

CONTACTInternational Journal of Electrical and Computer Engineering Systems (IJECES)

Faculty of Electrical EngineeringJosip Juraj Strossmayer University of Osijek

Kneza Trpimira 2b31000 Osijek, Croatia

Phone: +38531224600, Fax: +38531224605,

e-mail: [email protected]

Volume 1, Number 1, June 2010Volume 1, Number 2, December 2010

Documents

Sensor-Based Intelligent Mobile Robot Navigation in ... · 1 Abstract – This paper presents sensor-based intelligent mobile robot navigation in unknown environments. The paper deals