Seeburg JCUSeeburg JCU--DEC KitDEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox

♦ MP3 Compact Flash Player ♦ Coin Operated or Free Play ♦ Integrated Power Amplifier ♦ Line-Out to External Amplifier ♦ Programmable Autoplay ♦ IR Wireless Remote ♦ Digital LED Display ♦ 10,000 Songs

You can even make

selections directly from your remote control ...

KIT CONTENTS "Everything You Need - Nothing Else Is Required"

12VDC, 1 Amp Power Supply

Compact Flash Memory Card

6-foot Line-Out Audio Cable

USB2.0 CF Reader/Writer

Wireless IR Remote Control

Wire Harness Assembly Includes Coin Switches & #12 Illumination Lamps

MP3-DSP Compact Flash Player System

Digital Display & IR Sensor

LED Filter Lens

Misc Hardware

Pricing Card

Remove and save the two screws from the coin switch unit.

Remove harness clamp.

Remove two screws from door support bracket.

Remove terminal strip mounting screws.

Align the JCU player board to the three molded boss positions.

Mark the mounting hole corners and drill four 9/64" holes.

Bo

ss

Boss

Bo

ss

At the back panel, unplug the 3 harness connectors. Remove the DTP1 unit, Power Circuit Board, and coin mechanism. Remove and save the two screws from the coin switch unit. Remove all other harness mounting hardware (screws, clamps, etc). At the front door, unplug the 4 harness connectors, disconnect 6 fast-on terminals from keypad & speakers, pull up the 4 illumination lamp sockets. Remove the lamp board, it's not used.

Remove the cable hold-down clamp (part of the speaker mounting screw). Remove and save the two screws holding the strap band to the door latch bracket. Leave the bracket in place for the new harness. ⇒ Remove the entire wire harness.

Align the MP3 player unit below the top back panel bosses and to the right of the side boss, mark the four mounting hole corners, drill 9/64" holes and countersink at the rear. Insert 6-32 x 1/2" flat head machine screws, nylon spacers and nuts.

This is the inside of an unmodified Seeburg DEC wallbox.

Summary of conversion steps 1) The old electronics will be removed. 2) Four holes will be drilled to mount the MP3 player unit. 3) The lamp board will be removed. 4) The front panel will be changed around for the LED digital display. 5) Two jumper wires will be soldered on the volume control board. 6) A new wiring harness will be installed. 7) The illumination lamps will be changed from #19 to #12.

Now to begin the conversion process ...

On the front door assembly ... At the volume control board, remove the audio relay and insert two jumper wires.

Remove the keypad/display bezel (4 corner nuts and 1 6-32 screw at the center, near the volume control assembly). Take out the Credit Window glass. Move the clear Pricing Window glass to the old credit window position. Place the new red LED filter lens in the old pricing window position. A thin piece of 3M double stick, 1/16" foam tape at an edge will keep the glass and LED filter in place. Place two small pieces of 1/16" foam tape at each end of the lamp hole guides. Place the pricing card so it will show behind the clear glass. ⇒ Re-install keypad/display bezel. On the new LED display board, place four cut pieces of self-stick rubber foam weather seal around the four LED digits and IR sensor on the display board (Frost King Black R738, 3/8" wide, 7/16" thick). Position the display board to the corner, up against the cast metal keypad and volume control positions. You can use some black tape to help hold the board in place. Place a 1-inch piece of 3M double stick, 1/16" foam tape at the corner of the display board as shown. Carefully place the clear plastic program light guide on top of the display board, which will stick to the foam tape and keep the display board in place. NEXT STEP ...... ⇒ Install the new wire harness assembly.

Foam padding

around display

Double stick foam tape

Display Board

Volume Board

Right Speaker

Left Speaker

Illumination Lamp

Illumination Lamp Illumination

Lamp

Illumination Lamp

Keyp

ad C

on

necto

r

Keypad Switch

DC Power Connector

Line Out Audio Connector Coin

Switches

P5

P4 P3 P2

P1

P7

J3 JCU Player

Harness Assembly Diagram

Back Panel

J3 - Line Out audio P1 - 12VDC Power input P2 - Speaker output P3 - LED Display output P4 - Keypad input P5 - Coin switch input P7 - IR Sensor input

Front Door

Remove Album/Single switch assembly (at back of keypad), it will not be used.

Install two screws to mount the strap band to the door latch bracket.

Plug in the three LED Display module connectors.

Plug in the volume control connector and keypad connector.

Attach the 6 fast-on terminal to the speakers and keypad switch. Left Speaker: 2 wires, Gray and White/Yellow Keypad Switch: 2 wires, Black and White Right Speaker: 2 wires, 2x Gray and White/Green

Insert #12 lamps into the lamp holders and push them into the light guide positions.

Insert the cable hold-down clamp (part of the speaker mounting screw).

Install the two screws saved earlier.

Install harness clamp screw.

Install two support screws.

Install harness clamp screw.

Harness clamp

Install strap band screws.

Install New Wire Harness to Back Panel

⇒ Mounting the JCU player board. Insert nylon spacers, position the MP3 player unit, mount into place using four nuts. Install two screws to mount the door support bracket. Form the wire harness into position and plug in all connectors. Insert two screws to mount the coin switches. Insert a screw to mount the harness clamps.

Install New Wire Harness to Front Door

Copyright © 2009 Data Sync Engineering. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.

"SEEBURG DEC CONVERSION KIT" MATERIALS LIST Assembly Name Qty Description Cost

Harness Assembly 1 Pre-wired, includes door support strap with all connectors, #12 lamps & coin switches 99.00

MP3 Player Unit Kit 1 JCU/DEC Player, includes 4GB CF, USB2.0 Reader, Wireless Remote, Line Out RCA 299.00

Power Supply 1 AC Power Adapter, 12VDC, 1A, with 2.1mm Plug, Center Positive, Part # 100870 10.80

Display Module 1 4-Digit LED Display & IR receiver circuit board, includes foam weather seal & tape 25.00

Display Filter 1 Red LED Display Filter Lens, 1-7/16 x 3-1/4 5.00

PCB Mounting Hardware 1 Machine screws, nylon spacers and nuts to mount the JCU player board 3.00

Data Sync Engineering P.O. Box 539, 2 Footbridge Lane Blairstown, New Jersey 07825

TEL: (908) 362-6299 www.datasynceng.com

www.cdadapter.com