SECTOR 30, Integrated Infrastructure Development, Naya Raipur · NRDA F-1 NAYA RAIPUR DEVELOPMENT AUTHORITY Tender Document for the Integrated Infrastructure Development for phase

NRDA F-1

NAYA RAIPUR DEVELOPMENT AUTHORITY

Tender Document for the

Integrated Infrastructure Development for phase 1 works of

Sector 12, 40 & other specified areas at Naya Raipur

(Following Three-Envelope Tender Procedure)

Schedule – A Price Tender

To be submitted in ENVELOPE-3

NIT No : 133/IID/S-12, 40 & SA. ( Phase-I) /EEC-III/ CE (E)/ NRDA / 2016-17,Naya Raipur, Dated: 10.11.2016

Issued by: Chief Executive Officer,

Naya Raipur Development Authority (NRDA)

Paryavas Bhawan, North Block Sector- 19,

Naya Raipur- 492 002, Chhattisgarh

Tel No: + 91 771 2512500; Fax No.: +91 771 2512400.

Website: www.nayaraipur.gov.in

http://www.nayaraipur.gov.in/

Integrated Infrastructure Development for phase 1 works of Sector 12, 40 & other specified areas at Naya Raipur NRDA

Signature of Contractor…………………………….... Signature of NRDA………………………..…………

Tender Document Contains (a) Only schedule “A” and Section-I of schedule “D” are to be filled & singed by the tenderer (b) All the certificates as per pre qualification criteria shall be appended with relevant forms of schedule”D”

1. PART ONE (NRDA F-1)-(Attached herewith, to be submit along the tender) Part (A)

a) Press Notice

b) Detailed NIT

Part (B)

a) Schedule-A

(i) Cost Abstract

(ii) Bill of Quantities

b) Schedule-B –NIL

c) Schedule-C –NIL

d) Schedule-D

Section-I................ Technical tender forms

(i) Letter of Technical Tender

(ii) Tenderer’s Information Sheet

(iii) Annual Turnover

(iv) Specific Construction Experience

(v) Declaration

(vi) Check list for Technical tender evaluation

Section –II ……………....Scope of work

Section –III..................... Technical specifications of work

Section –IV.................... Special Conditions of Contract

Section –V.................... List of approved makes

Section –VI..................... Drawings

e) Schedule-E

f) Schedule-F

2. PART TWO (NRDA F-2/3) )-Standard form (Not Attached herewith, and not to be submitted along the tender) Important note: - Link site http:// nayaraipur.com/documents/gcc.pdf

1. General Guidelines

2. Tender

3. General rules and directions

4. Conditions of contract

5. Clauses of contract

6. Model rules relating to labour, water supply and sanitation in labour camps safety code

7. Contract forms

(a) Draft Format for Performance Security

(b) Earnest Money Deposit Form (Bank Guarantee)

(c) Format of Contract Agreement

(d) Draft Format for Performance Guarantee for Water Proofing and Anti-termite Works

(e) Indemnity Bond

(f) Indenture Bond

(g) Notice for Appointment of Arbitrator

8. Proforma of schedules (Schedule ’A’ to Schedule ’F’)

Integrated Infrastructure Development for phase 1 works of Sector 12, 40 & other specified areas at Naya Raipur NRDA

Signature of Contractor…………………………….... Signature of NRDA………………………..…………

Naya Raipur Development Authority (NRDA)

Raipur, Chhattisgarh

Document details

Name of work : “Integrated Infrastructure Development for phase 1 works of Sector 12, 40 & other

specified areas at Naya Raipur”

Name of Tenderer:

Details

a) Cost of Tender Document : Rs

b) EMD : Rs

Signature of Tenderer

Date:____________

Sl. No. Description of Items Amount ( in INR) Amount in Words ( In INR )

A ROAD WORK Rs. -

B

UTILITY SERVICES: WATER SUPPLY, SEWERAGE

SYSTEM, DRAINAGE SYSTEM, UTILITY CROSSINGS,

BRIDGE CONSTRUCTION, NALA REALIGNMENT AND

TRAINING WORK, PARK DEVELOPMENTS &

ELECTRICAL DUCT ETC.

Rs. -

C ELEECTICAL WORK Rs. -

D AUTO TAXI STAND Rs. -

Total Amount in INR Rs. -

Cost abstract for

Integrated Infrastructure Development Works for Phase-I works at sector-12, 40 and other Specified areas at Naya Raipur

Sr. No Description of Item Unit Quantity Rate in

INR Rate in Words ( Indian Rupee) Amount in INR

A ROAD WORKS

1

Detailed survey of existing road including chaining, leveling,

with cross section at 25.0 m intervals and closing survey each day's

work,supply and of fixing bench marks, painting, taking trial pits

and submission of road cross sections, L-sections, quantity

statements in computerized prints in five copies in proper files and

all type of compliance required by the Engineer-in-charge.

Km. 26.17 Rs. -

2

Excavation in Soil (by Mechanical Means). Excavation for

roadway / drain in soil using mechanical means including loading

in tipper for carrying of cut earth to embankment site and unloading

with all lifts and lead as per relevant clauses of section 300.

Cum. 3,09,626.67 Rs. -

3

Cutting of trees, including cutting of trunks, branches and removal

of stumps, roots, stacking of serviceable material with all lifts and

lead and earth filling in the depression/pit and as per relevant

clauses of section-200 for :-

Each 149.00 Rs. -

Bill of Quantity


2 of 109



4

Clearing and grubbing road land including uprooting rank

vegetation, grass, bushes, shrubs, saplings and trees girth up to 300

mm, removal of stumps of trees cut earlier and disposal of

unserviceable materials and stacking of serviceable material to be

used or auctioned up to all lifts and lead including removal and

disposal of top organic soil not exceeding 150 mm in thickness if

required and as per relevant clauses of section-200. (A) In area of

light jungle

Hectare. 14.85 Rs. -

5

Construction of embankment / sub-grade with Material

Obtained from Borrow Pits (Construction of embankment with

approved material/selected soil having C.B.R. (as specified in the

contract and construction drawings) obtained from borrow pits with

all lifts and leads, transporting to site, spreading, grading to

required slope and compacting to meet requirement of table 300-2)

as specified by in the drawigns and Engineer in charge.

Cum. 3,39,033.89 Rs. -

6

Compacting Original Ground (ii) Compacting Original

Ground supporting sub-grade Loosening and compacting

original ground to facilitate placment of first layer of embankment

scarified to a depth of 150mm mixed with water at O.M.C and then

compacted by rolling so as to achieve minimum dry density as

given in table 300-2 for embankment construction

Cum. 29,871.28 Rs. -

3 of 109



7

Construction of Embankment with Material Deposited from

Roadway Cutting (Construction of embankment with approved

materials having C.B.R. (as specified in the contract) deposited at

site from roadway cutting and excavation from drain and

foundation of other structures graded and compacted to meet

requirement of table 300-2)

Cum. 43,945.44 Rs. -

8

Granular Sub-base as per Table:- 400-1Construction of granular

sub-base by providing close graded Material, , carriage of mixed

Material to work site, spreading in uniform layers with motor

grader on prepared surface watering, rolling and compacting with

vibratory power roller at OMC to achieve the desired density,

complete as per clause 401 . (A) Plant mix method (with

Mechanically crushed stone only) (iii) for grading-III Material

Cum. 66,743.21 Rs. -

9

Wet Mix Macadam (Providing, laying, spreading and compacting

graded stone aggregate to wet mix macadam specification including

premixing the Material with water at OMC in mechanical mix plant

carriage of mixed Material by tipper to site, laying in uniform

layers with paver in sub- base / base course on well prepared

surface and compacting with vibratory roller to achieve the desired

density as per clause 406.)

Cum. 58,625.90 Rs. -

4 of 109



10

Dense Bituminous Macadam(Providing and laying dense

bituminous macdam with minimum 40-60 TPH capacity HMP

using crushed aggregates of specified grading, premixed with

bituminous binder @4.0 to 4.5% by weigth of toal mix of mix and

filler, transporting the hot mix to work site laying with hydrostatic

paver finisher to the required grade, level and alignment, rolling

with smooth wheeled, vibratory and tandem rollers to achieve the

desired compaction as per MORTH specification clause N0.505

complete in all aspects.) A. (ii) with sensor paver finisher for

Grading -II(26.5mm nominal size bitumen content 4.50%)

Cum 11,676.64 Rs. -

11

Bituminous Concrete ( providing and laying bituminous concrete

with minimum 40-60 TPH capacity hot mix plant using crushed

aggregates of specified grading, premixed with bituminous binder

@ 5.0 to 6.0% by weight of total mix of mix and filler, transporting

the hot mix to work site, laying with a hydrostatic paver finisher

with sensor control to the required grade, level and

alignment,rolling with smooth wheeled, vibratory and tandem

rollers to achieve the desired compaction as per MORTH

specification caluse No.507 complete in all repsects) A.(iii) with

sensor paver finishere for Grading -II(13.2mm nominal size) with

bitumen 6.0%

Cum 9,342.75 Rs. -

12

Prime Coat ( Providing and applying primer coat with oil based

bitumen emulsoion (SS-I, grade confirming to IS:8887) on

prepared surface of granular Base including clearing of road

surface and spraying primer using mechanical means as per cluse

502.

5 of 109



a (i) on WBM/WMM surface @0.85 Kg/sqm. 2,33,464.61 Rs. -

13

Tack Coat Providing and applying tack coat with bitumen

emulsion(RS-1, grade confirming to IS:8887) using emulsion

pressuredistributor on the prepared bituminous/granular surface

cleaned withmechanical broom and as per clause 503.

Sqm

a (i) Bituminous surface @ 0.25 kg /Sqm 2,33,464.61 Rs. -

b (i) Granular surface treated with prime @ 0.30 kg /Sqm 2,33,464.61 Rs. -

14

Cement Concrete Pavement (Construction of un-reinforced, dowel

jointed, plain cement concrete pavement over a prepared sub-base,

coarse and fine aggregate conforming to IS:383, and graded as per

table 600-3, mixed as per approved mix design at site, laid,

Cum 2,021.90 Rs. -

6 of 109



15

Dry Lean Cement Concrete Sub-base as per IRC:SP-49

(Construction of dry lean cement concrete Sub-base over a

prepared sub-grade with coarse and fine aggregate conforming to

IS: 383, the size of coarse aggregate not exceeding 26.5 mm,

aggregate cement rati

Cum 1,011.00 Rs. -

16

Providing & Laying precast Interlocking concrete blocks of

minimum compressive strength of 300kg/sq.cm and approved size,

shape /pattern over coarse sand bed of thickness upto 40mm and

joints thick filled with fine sand includind leveling with surface

vibrator, temping and sweeping etc .complete as per IRC-SP-63-

2004

Sqm 98,607.29 Rs. -

15

Cast insitu Cement Concrete M20 Kerb with Channel(

construction of cement concrete kerb with channel with top and

bottom width 115 and 165mm repectively, 250mm high in M20

grade PCC on M10 grade foundation 150mm thick , kerb channel

300mm wide, 50mm thick in PCC M20 grade, sloped towards the

kerb, kerb stone with channel laid with kerb laying machine,

foundation concrete laid manually all complete as per clause 409).

Meter 33,912.23 Rs. -

7 of 109



17

Cast in Situ Cement Concrete M20 kerb (Construction of

cement concrete kerb with top and bottom width 115 and 165 mm

respectively, 250 mm high in M20 grade PCC on M10 grade

foundation 150 mm thick, foundation having 50 mm projection

beyond kerb stone, kerb stone laid with kerb laying machine,

foundation concrete laid manually, all complete as per clause 408)

Meter 37,476.02 Rs. -

18

Painting on Concrete Surfaces (A)Two coats on new surfaces

(Painting two coats after filling the surface with synthetic enamel

paint in all shades on new plastered concrete surfaces)

Sqm 26,991.72 Rs. -

19

Boundary pillar (Reinforced cement concrete M15 grade boundary

pillars of standard design as per IRC:25-1967, fixed in position

including finishing and lettering but excluding painting)

each 103.31 Rs. -

20

Road Marking with Hot Applied Thermoplastic Compound

with Reflectorizing Glass Beads on Bituminous Surface

(Providing and laying of hot applied thermoplastic compound 2.5

mm thick including reflectorizing glass beads @ 250 gms per sqm

area, thickness of 2.5 mm is exclusive of surface applied glass

beads as per IRC:35-1997. The finished surface to be level,

uniform and free from streaks and holes.)

Sqm 14,036.34 Rs. -

8 of 109



21

Retro- reflectrorized Traffic signs (Providing and fixing of retro-

reflectrorized cautionary, mandatory and informatory sign as per

IRC:67-2012 made of encapsulated lens type reflective sheeting

vide clause 801.3, fixed over aluminum sheeting, 1.5 mm thick

supported on a mild steel frame of size 40 x 40 x 5 mm and mild

steel angle iron post 75 mm x75 mm x 6mm firmly fixed to the

ground by means of properly designed foundation with M15 grade

cement concrete 45 cm x 45cm x 60cm, 60 cm below ground level

as per approved drawing)

a 60 cm x 45 cm rectangular Each 65.00 Rs. -

b 60 cm equilateral triangle Each 65.00 Rs. -

c 60 cm Circular 64.00 Rs. -

d 90 cm high octagon Each 67.00 Rs. -

Sub Total of Road Works Rs. -

9 of 109

Sr.

NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR

B UTILITY SERVICES

1

Earth work in excavation for pipe trench in all type soil

areas including dressing, watering and ramming and

disposal of excavated earth with all lead and lift, disposal

earth to be leveled, neatly dressed including clearing of

vegetation, shoring, strutting, de-watering, bailing of

water met due to all causes including lowering of water

table required to keep the trench in the dry condition to

facilitate for laying, jointing and testing of works and

backfilling with approved materia, all complete as per

technical Specifications and as per direction of Engineer.

i upto 1.5 m deep Cum 2,07,735.49 Rs. -

2

Earth work in excavation for pipe trench in ordinary soil







facilitate for laying, jointing and testing of works all

complete as per technical Specifications and as per

direction of Engineer.

i >1.5m and upto3.0m deep Cum 45,056.97 Rs. -

Bill of Quantity


Page 10 of 109

Sr.


ii >3.0m and upto 4.5m deep Cum 22,945.00 Rs. -

3

Earth work in excavation for pipe trench in Hard Soil







facilitate for laying, jointing and testing of works all



i >1.5m and upto 3.0m deep Cum 4,736.00 Rs. -

ii >3.0m and upto4.5m deep Cum 2,405.00 Rs. -

4

Earth work in excavation for pipe trench in all kinds of

rocks in areas including dressing, stacking of useful

material and disposal of unserviceable one up to 50 m

lead and lift up to 4.5m. all complete as per technical

Specifications and as per direction of Engineer.

i Hard rock requiring blasting. Cum 60.00 Rs. -

Page 11 of 109

Sr.


iiHard rock requiring chiselling / where blasting is

prohibited.Cum 60.00 Rs. -

5

Filling available excavated earth in trenches, plinth sides

of foundation in layers not exceeding 20cm. in depth

including consolidation of each layer by ramming

watering, lead upto 50m and lift up to all depth in all

kinds of soils all complete as per technical Specifications

and as per direction of Engineer.

cum 80,774.00 Rs. -

6

Providing and filling in plinth with sand/ Crusher dust

under floor in layers not exceeding 20cm in depth

consolidating each deposited layer by ramming and

watering, including dressing etc. complete.

cum 7,964.62 Rs. -

7

Providing and laying nominal mix plain cement concrete

with crushed stone aggregate using concrete mixer in all

works upto plinth level excluding cost of form work. all



i1:3:6 (1 cement : 3 coarse sand : 6 graded stone

aggregate 40mm nominal size).Cum 2,589.23 Rs. -

ii1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate 40mm nominal size).cum 176.00 Rs. -

Page 12 of 109

Sr.


8

Construction of RCC drain/ chamber/ Thrust

block/Encasement/tanks/cover/park works etc. placing in

position, providing shuttering and concreting by using

concrete mixer, compaction by vibration etc complete as

per drawings and technical specifications excluding

reinforcement.

i RCC M-20 Cum 24,118.10 Rs. -

9

Providing and laying design mix reinforced cement

concrete with crushed graded stone aggregate 20mm

nominal size using batching plant, transit mixer and

concrete pump, in all works upto plinth level excluding

cost of form work. all complete as per technical


i RCC M-20 Cum 1,365.00 Rs. -

10

Providing,laying and placing of precast cement concrete

cover of drain M-35 grade in superstructure including

form work but excluding reinforcement complete .

Cum 87.98 Rs. -

11

Providing and fixing form work including centring,

shuttering, strutting, staging, propping bracing etc.

complete and including its removal at all levels, for:

i

Foundations, footings, bases of columns plinth beam,

curtain wall in any shape and size and all type of wall

below plinth level.

Sqm 3,984.50 Rs. -

Page 13 of 109

Sr.


iiColumns, Pillars, Piers and likes- rectangular or square in

shapeSqm 54.00 Rs. -

iiiSuspended floors, roofs, access platform, balconies (plain

surfaces) and shelves (cast in situ) Sqm 24.00 Rs. -

iv Beams, lintels, cantilevers & walls sqm 30.15 Rs. -

12

Providing and mixing water proofing material in PCC/ RCC

work in the proportion recommended by the

manufacturer. all complete as per technical Specifications


kg 23.94 Rs. -

13

Providing and placing in position reinforcement for R.C.C.

work including straightening, cutting, bending, binding

etc. complete as per drawings including cost of binding

wire in foundation and plinth all complete as per


i Thermo-Mechanically Treated bars FE -500D kg 18,15,906.27 Rs. -

Page 14 of 109

Sr.


14

Providing, laying, Jointing & field testing of High Density

Polyethylene pipes, (HDPE) Conforming to IS4984/ 14151/

12786/ 13488 including all accessories (for specials

10kg/sq.cm) i.e. tees, bends, reducers, end caps etc and

fittings with necessary jointing material like mechanical

connector or jointing pipes by heating to the ends of

pipes with the help of Teflon coated electric mirror/

heater to the required temperature and then pressing the

ends together against each other, to form a monolithic &

leak proof joint by thermo setting process. It may be

required to be done with Jacks/ Hydraulic Jacks /But

fusion machine. (50mm & above fusion jointed & below

50 mm mechanical jointed) all complete as per technical


i 75 mm dia.(PE-100) 6 Kg/sq.cm Rm 4,740.00 Rs. -

ii 110 mm dia.(PE-100) 6 Kg/sq.cm Rm 11,050.00 Rs. -

iii 160 mm dia.(PE-100) 6 Kg/sq.cm Rm 10,630.00 Rs. -

iv 200 mm dia.(PE-100) 6 Kg/sq.cm Rm 15,170.00 Rs. -

Page 15 of 109

Sr.


15

Providing, laying and jointing socket & spigot centrifugally

cast (Spun) Ductile Iron pressure pipes with inside cement

mortar lining (classK-7) Conforming to IS8329/2000 with

suitable Rubber Gasket (Pushon) joints as per IS:5382/85

including testing of joint (laying Conforming to IS 12288 :

1987) all complete as per technical Specifications and as

per direction of Engineer.

i 300mm diameter Rm 12,450.00 Rs. -

ii 400mm diameter Rm 800.00 Rs. -

Page 16 of 109

Sr.


16

Providing & Supplying D.I. Specials & Fittings For all types

of specials, bends, reducers, tees. etc. all complete as per


i 80 to 300 mm dia Kg 12,336.00 Rs. -

ii 350 mm and above dia Kg 589.00 Rs. -

17

Providing, laying and jointing of pig lead at site of work.

all complete as per technical Specifications and as per


quintal 0.55 Rs. -

18

Providing & fixing of Cast iron double flanged sluice valves

as per I.S.:14846-2000 fitted with cast iron cap including

jointing & testing with cost of jointing material such as

bolts, nuts, rubber insertions etc. all complete. (Steel

Spindle) all complete as per technical Specifications and

as per direction of Engineer.

i 80 mm diameter (Pressure rating PN - 1.6) Each 12.00 Rs. -

Page 17 of 109

Sr.


ii 100 mm diameter (Pressure rating PN - 1.6) Each 50.00 Rs. -

iii 150 mm diameter (Pressure rating PN - 1.6) Each 17.00 Rs. -

iv 200 mm diameter (Pressure rating PN - 1.6) Each 24.00 Rs. -

v 300 mm diameter (Pressure rating PN - 1.6) Each 16.00 Rs. -

vi 400 mm diameter (Pressure rating PN - 1.6) Each 3.00 Rs. -

19

Providing & fixing cast iron double air valves, flanged

without in-built isolating valve as per IS:14845-2000

including jointing & testing with cost of jointing material

and rubber insertion all complete as per IS :13095-1991

all complete as per technical Specifications and as per


i 80 mm dia PN-1.6 Each 4.00 Rs. -

Page 18 of 109

Sr.


ii 100 mm dia PN-1.6 Each 18.00 Rs. -

20

Providing, Laying & Jointing of welded double flanged

centrifugal cast (spun)ductile Iron pressure pipes

Conforming to IS:8329/2000 in the length of 1m. For class

K-9 with inside cement mortar lining for the sizes /dia

pipes. (laying Conforming to IS 12288 : 1987) all complete

as per technical Specifications and as per direction of

Engineer.

i 80mm Each 2.00 Rs. -

ii 100mm Each 11.00 Rs. -

21

Providing, Laying & Jointing of welded double flanged

centrifugal cast (spun)ductile Iron pressure pipes

Conforming to IS:8329/2000 in the length of 2m. For class

K-9 with inside cement mortar lining for the sizes /dia

pipes. (laying Conforming to IS 12288 : 1987) all complete


Engineer.

i 80mm Each 2.00 Rs. -

Page 19 of 109

Sr.


ii 100mm Each 15.00 Rs. -

Page 20 of 109

Sr.


22

Providing & Laying Ductile Iron Double Socket branch

flange Tee Conforming to IS-9523/2000 having dimension

as per table 21 of IS-9523/2000 in the nominal

diameter/sizes with external bitumen coating and internal

cement mortar lining with finishing as per clause 13 of IS-

9523/2000. (laying Conforming to IS 12288 : 1987) (All

sizes in mm) all complete as per technical Specifications


i 150x80 Each 2.00 Rs. -

ii 200x80 Each 1.00 Rs. -

iii 300x100 Each 14.00 Rs. -

iv 400x100 Each 1.00 Rs. -

23

Providing, laying, jointing, testing and commissioning of

D.I Dismantling joint with M.S. Nut stud & washers coated

for rust prevention & internal rubber rings etc. complete

assembly set as per type design inclusive of all taxes &

duties, insurance, loading/ unloading & stacking FOR at

site all complete as per technical Specifications and as per


Page 21 of 109

Sr.


i 80 mm diameter Each 10.00 Rs. -

ii 100 mm diameter Each 50.00 Rs. -

iii 150 mm diameter Each 19.00 Rs. -

iv 200 mm diameter Each 24.00 Rs. -

v 300 mm diameter Each 16.00 Rs. -

vi 400 mm diameter Each 2.00 Rs. -

Page 22 of 109

Sr.


24

Providing 1st class bedding below pipes with graded sand

or other granular materials passing through 5.6 mm sieve

as per clause 2904. all complete as per technical


Cum 19,399.00 Rs. -

25

Supply, installation, testing and commissioning of

electromagnetic full bore meter complete as per specification

including transportation to site, storage, safety, installation,

testing, commissioning, making connections with existing pipe

line, including excavation at site, cuts in the existing pipe system,

dewatering and reinstating the same after completion of

installation as per specification and drawings including all taxes.

Accuracy of meter +/- 0.3% - 0.5% of measured value, Flange

connection as per AWWA & IS, fully welded sensor housing

complying to IP 68 standard, Electrodes SS 316/Hastelloy C, cable

gland 1/2" NPT, Sensor housing fully welded SS 304 housing with

protective Polyurethane paint/Die Cast Aluminium with anti

corrosive grade paint/Carbon Steel ASTM A 105 with corrosion

resistant two component epoxy coating (min 150 µm), Flow

Transmitter/ Converter: Microprocessor based, modular design

display 2 line back lit LCD for indication of actual flow rate,

forward, reverse, sumtotalizer, Perfection category: IP 65.

Output: One current output (4-20 mA) one scalable pulse output.

The required cable and mounting accessories for remote type

transmitter mounting shall be included (Maximum distance of 30

meters or as per site condition).Instrument shall be based on

open protocol and SCADA compatible, complete in all respect as

per technical specification including all specials and fittings and as

per direction of Engineer in Charge.

i EFM 50 for DN 50mm Each 8.00 Rs. -

Page 23 of 109

Sr.


ii EFM 80 for DN 80mm Each 6.00 Rs. -

iii EFM 100 for DN 100mm Each 1.00 Rs. -

iv EFM 150 for DN 150mm Each 4.00 Rs. -

v EFM 200 for DN 200mm Each 1.00 Rs. -

vi EFM 300 for DN 300mm Each 3.00 Rs. -

26

Supply, installation, testing and commissioning of Dirt Box

with S.S. Strainer as per specifications (Dia in mm) as

required all complete as per technical Specifications and

as per direction of Engineer.

i 15 mm nominal outer dia pipes Each 3.00 Rs. -

ii 20 mm nominal outer dia pipes Each 3.00 Rs. -

Page 24 of 109

Sr.


iii 40 mm nominal outer dia pipes Each 3.00 Rs. -

iv 50 mm nominal outer dia pipes Each 8.00 Rs. -

v 80 mm nominal outer dia pipes Each 6.00 Rs. -

vi 100 mm nominal outer dia pipes Each 1.00 Rs. -

vii 150 mm nominal outer dia pipes Each 4.00 Rs. -

viii 200 mm nominal outer dia pipes Each 1.00 Rs. -

ix 300 mm nominal outer dia pipes Each 3.00 Rs. -

Page 25 of 109

Sr.


27

Construction of RCC valve chamber internal size 1.2m x

1.2m x 1.5m, 100mm thick PCC- M10 and RCC M20 grade

150mm thick wall, precast cover 125mm thick slab on top

for protection of valve coming under traffic & extended

MS valve operating spindle rod as reqd etc. Including

steel reinforcementon 10mm dia. 150mm c/c bothways

wall & precast cover, shuttering, labour charges etc as

per drawing and as per direction of Engineer complete

etc.

No 131.00 Rs. -

28

Construction of RCC valve chamber internal size 2.5m x

1.2m x 1.5m, 100mm thick PCC- M10 and RCC M20 grade

150mm thick wall, precast cover 125mm thick slab on top

for protection of valve coming under traffic & extended

MS valve operating spindle rod as reqd etc. Including

steel reinforcementon 10mm dia. 150mm c/c bothways

wall & precast cover, shuttering, labour charges etc as

per drawing and as per direction of Engineer complete

etc.

No 8.00 Rs. -

29

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes, having thermal stability for hot & cold water supply

including all CPVC plain & brass threaded fittings. This

included jointing of pipes & fittings with one step CPVC

solvent cement, trenching, refilling & testing of joints

complete as per direction of Engineer in Charge.

a EXTERNAL WORK

i 15 mm nominal outer dia pipes Rm 65.00 Rs. -

ii 20 mm nominal outer dia pipes Rm 1,430.00 Rs. -

Page 26 of 109

Sr.


iii 25 mm nominal outer dia pipes Rm 50.00 Rs. -

iv 32 mm nominal outer dia pipes Rm 645.00 Rs. -

v 40 mm nominal outer dia pipes Rm 15.00 Rs. -

vi 50 mm nominal outer dia pipes Rm 250.00 Rs. -

vii 100 mm nominal inner dia pipes Rm 3.00 Rs. -

30

Providing and Supplying of following G.I. Specials as per

relevant IS1239, ISI marked for usage in Drinking water

inclusive of all materials, Central, State and Municipal

taxes and duties inspection charges, transit insurance,

loading/unloading FOR site unloading & stacking etc.

complete as per direction of Engineer-in-Charge.

M.S.Saddle Piece

i 15 Each 15.00 Rs. -

Page 27 of 109

Sr.


ii 20 Each 285.00 Rs. -

iii 25 Each 10.00 Rs. -

iv 32 Each 300.00 Rs. -

v 50 Each 15.00 Rs. -

vi 100 Each 1.00 Rs. -

31

Providing and Supplying of Saddle Piece, duly tested from

certified agencies for usage in Drinking water inclusive of

all materials, Central, State and Municipal taxes and

duties inspection charges, transit insurance, loading /

unloading FOR site unloading & stacking etc. complete as

per direction of Engineer-in-Charge.

i 160 x 32 mm dia Each 30.00 Rs. -

Page 28 of 109

Sr.


ii 110 x 20 mm dia. Each 3.00 Rs. -

iii 110 x 32 mm dia. Each 100.00 Rs. -

iv 110 x 40 mm dia. Each 3.00 Rs. -

v 110x 50 mm dia. Each 5.00 Rs. -

Page 29 of 109

Sr.


32

Providing and fixing GM or brass ferrules Conforming to IS-

2692/1984 (Reaffirmed2005), tested to 21.00kg/sq.cm.

i/c boring and tapping the main all complete as per


i 32 mm dia. Each 25.00 Rs. -

ii 40 mm dia. Each 10.00 Rs. -

iii 50 mm dia. Each 1.00 Rs. -

33

Providing and fixing ball valve (brass) of approved quality,

High or low pressure, with plastic floats complete : all



i 15 mm dia each 15.00 Rs. -

ii 20 mm dia each 288.00 ` Rs. -

Page 30 of 109

Sr.


iii 25 mm dia each 10.00 Rs. -

34

Providing and fixing brass/ gun metal gate valve with C.I.

wheel of approved quality (screwed end): all complete as

per technical Specifications and as per direction of

Engineer.

i 32 mm dia each 15.00 Rs. -

ii 40 mm dia each 3.00 Rs. -

iii 50 mm dia each 21.00 Rs. -

35

Supply, installation, testing and commissioning of Multi

Jet, dry-dial, inferential type, horizontal, Magentically

coupled, class 'B'water meters Conforming to IS-779:

1994 and ISO 4064:1993 standard with EEC/MID

certification mark, with IP68 protection class copper can

register with 5 mm tempered mineral glass cover,

successful Life Cycle Test Certificate from FCRI and AMR

compatibility with 5 years warranty complete with brass

nuts and nipples. Instrument shall be complete in all

respects according to technical specifications including all

specials

i 15 mm nominal outer dia pipes Each 3.00 Rs. -

Page 31 of 109

Sr.


Page 32 of 109

Sr.


ii 20 mm nominal outer dia pipes Each 3.00 Rs. -

iii 40 mm nominal outer dia pipes Each 3.00 Rs. -

36

Constructing masonry Chamber 60x60x75 cm, inside with

modular well burnt clay bricks of 35 kg/ cm² in cement

mortar 1:4 (1 cement : 4 coarse sand) for sluice valve,

with C.I. surface box 100mm. top diameter, 160 mm

bottom diameter and 180 mm deep (inside) with chained

lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand :

4 graded stone aggregate 20mm nominal size) necessary

excavation foundation concrete 1:5:10 (1 cement : 5 fine

sand : 10 graded stone aggregate 40 mm nominal size)

and inside plastering with cement mortar 1:3 (1 cement :

3 coarse sand) 12 mm thick finished with a floating coat

of neat cement complete as per standard design : all



Each 16.00 Rs. -

37

Constructing masonry Chamber 90x90x100 cm, inside

with modular well burnt clay bricks of 35 kg/ cm² in

cement mortar 1:4 (1 cement : 4 coarse sand) for sluice

valve, with C.I. surface box 100mm. top diameter, 160

mm bottom diameter and 180 mm deep (inside) with

chained lid and RCC top slab 1:2:4 mix (1 cement : 2

coarse sand : 4 graded stone aggregate 20mm nominal

size) necessary excavation foundation concrete 1:5:10 (1

cement : 5 fine sand : 10 graded stone aggregate 40 mm

nominal size) and inside plastering with cement mortar

1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a

floating coat of neat cement complete as per standard

design :

Each 309.00 Rs. -

Page 33 of 109

Sr.


38

Meter box and cover : Supply, installation, testing and

commissioning of UV resistant, high density polyethylene

material size: length 870mmx width=655mm x depth

690mm, yet lightweight, specially designed to withstand

light vehicle load. Ease of opening and closing of top

cover shall be ensured with locking arrangement and

enclosure shall have enough mechanical strength

including cement concrete foundation 1:3:6 (1 cement : 3

coarse sand : 6 graded stone aggregate 40mm nominal

size), size of foundation= 1100X900X400mm and

formwork shuttering & removing all complete as per

standered specifications, and as per direction of

Engineer.

Each 10.00 Rs. -

Page 34 of 109

Sr.


Mechanical and Electrical works

39

Providing and Supplying of following Open well

submersible Pump set with ISI mark IS14220 (horizontal)

without panel board, duly tested from certified agencies

for usage in Drinking water inclusive of all materials,

Central, State and Municipal taxes and duties inspection

charges, transit insurance, loading/unloading FOR site

unloading & stacking etc. complete as per direction of

Engineer-in-Charge.

aSubmersible pump 150mm dia. (with Bronze Impeller)up

to 12 stages

i 20 HP, 1250 LPM at a head of 40 metres, Each 12.00 Rs. -

40

Supplying and laying following sizes one number PVC

insulated, PVC sheathed, steel armoured, aluminium

conductor power cable of 1.1 KV grade direct in ground

including excavation, sand cushioning, protective covering

and refilling the trench etc as required.

i 4 x 16 sq. mm. Meter 240.00 Rs. -

Page 35 of 109

Sr.


41

Supply, installation, testing and commissioning of cubicle

type wall/ floor mounted power cum control panel made

out of not less than 1.6 mm thick MS sheet and

comprising of following panel mounting switchgears there

in including connection inter-connection etc. as required.

a) Phase indicating lamps with fuses and toggle switches 1

set b) Star-delta starter suitable for 7.5 HP 3 phase AC

induction motor with over load and no volt relay c) 32 A

"C" series TPMCB 1 No d) Voltmeter 0-500 V with selector

switch 1 set e) Ammeter 0-10 A with CT's and selector

switch 1 set. all complete as per technical Specifications


Set 6.00 Rs. -

42

Supplying and installing pressure gauge of 100 mm Ø., 0-

300 PSI or 0-21 kg per cm square fitted with 12/15 mm Ø.

pad cock valve, and G.I. pipe, elbow etc. as per

requirement in approved manner. all complete as per


Each 12.00 Rs. -

43

Supply, erection, jointing, testing & commissioning of "C"

Class MS pipes (as per IS: 1239) including necessary

specials such as tees, bends, flanges reducers etc.,

complete on wall/ ceiling. The pipes to be erected on wall

or suspended from beams, RCC roof slabs with suitable

size MS bars/ angle irons including painting of metal part

except pipe line. all complete as per technical


i 80mm dia. Rm. 303.00 Rs. -

Page 36 of 109

Sr.


ii 100mm dia. Rm. 11.00 Rs. -

44

Fabrication of M.S. Pipes, grils and Specials: Fabrication

of M.S. pipes & specials as per IS specifications with inside

& outside epoxy coating as per relevant IS code, duly

tested for usage in Drinking water inclusive of all

materials, Central, State and Municipal taxes and duties in

spection charges, transit insurance, loading / unloading

FOR site unloading & stacking etc. complete as for

direction of Engineer-in-Charge. (all thickness) all



MT 6.60 Rs. -

45

Painting for M.S. pipe with a coat of red oxide primer and

two or more coats of synthetic enamel paint of approved

colour and Quality to give an even shade including surface

preparation.

i 80mm dia. Rm 300.00 Rs. -

46

Providing and fixing following cast iron double flanged

single door reflux (non return) valve including jointing and

testing with cost of jointing material such as bolts, nuts

and rubber insertion all complete as per IS:5312 9 (Part I)

i 80 mm dia. (Class -PN 1.0 rating) No 12.00 Rs. -

Page 37 of 109

Sr.


47

Providing, laying, Jointing & field testing of DWC HDPE

Pipes (with external annular corrugation and smooth

internal walls) duly tested Conforming to IS 16098 (PART-

II): 2013 having stiffness class of SN 8 with ring stiffness

not less than 8.00KN/SQM. and impact resistance TIR

valve not more than 10% including necessary jointing

materials for non-pressure underground sewerage,

drainage & cross drainage application. Inclusive of all

taxes related to central, state and municipal, inclusive of

excise duty, inspection charges, transportation charges,

transit insurance, loading/unloading and stacking at

site/store etc. and as per Technical Specifications and as

per direction of Engineer.This is also inclusive of Jointing

material i.e Pipe with online/offline coupler and

elastomeric sealing ring. All the joints shall be confirmed

water tight as per standards.

i 250/295 mm dia. RM 500.00 Rs. -

ii 300/345 mm dia. RM 5,300.00 Rs. -

iii 400/480 mm dia. RM 13,800.00 Rs. -

iv 600/715 mm dia. RM 4,800.00 Rs. -

Page 38 of 109

Sr.


Construction of prefabricated HDPE manhole:

Supplying , Installation testing and commissioning of

prefabricated HDPE manhole: Providing, lowering, laying,

aligning, fixing in position at all level/ depths High Density

Poly Ethylene (HDPE) manhole conforming to EN 13598-

2:2009, man entry type of 1000mm diameter for depth

specified below, shall be of single wall construction OR

modular construction conforming to EN 681-1 with triple

safety seal (three side lip/element) made of 100% virgin

PE material without recycling or foam content, including

connecting the according to EN 681-1 and the manholes

shall be safeguarded against uplift pressure with solid

horizontal reinforcement ribs of appropriate thickness

and with at regular intervals all along the outside of the

manhole.( Make : VECTUS INDUSTRIES LTD / equivalent)

48

Page 39 of 109

Sr.


The item is inclusive of Excavation, Dewatering, Layerwise

backfilling and compaction of grannular material ,

Provision of corrosion resistant steps at a vertical distance

of 25cm .Providing and fixing of FRP Manhole frame and

cover with locking arrangement fitting to 600mm dia

manhole openings and load should be carry 20tone

approved brand and as per IS:1726:1991etc.

Providing and fixing of Precast RCC M35 grade load

distribution ring 1050mm OD & 635mmID and designed

to handle heavy load as approved by Engineer placed

around the neck of the manhole of 150mm thickness

including reinforcement. Providing RCC M20 grade

concrete thick 200mm slab (Dia 1500mm outer dia and

inner dia 635mm ) around the manhole below the

Precast RCC distribution Ring. Providing and laying

Manhole bottom PCC (1:3:6) of 200mm thick and 1.5m

dia. All the inlet, outlet connections to the manhole shall

be complete with all accessories/ fittings, material,

labour, jointing materials , testing and commissioning as

per detailed drawing, as per Technical specifications and

all complete as directed by Engineer in charge.

1000 mm diameter circular manhole

i Manhole of depth up to 1.2m No 70.00 Rs. -

ii For depth above 1.2m and up to 1.8m No 60.00 Rs. -

iii For depth above 1.8m and up to 2.1m No 70.00 Rs. -

48

Page 40 of 109

Sr.


iv For depth above 2.1m and up to 2.4m No 77.00 Rs. -

v For depth above 2.4m and up to 2.7m No 113.00 Rs. -

vi For depth above 2.7m and up to 3.0m No 150.00 Rs. -

vii For depth above 3.0m and up to 3.6m No 90.00 Rs. -

vii For depth above 3.6m and up to 4.2m No 95.00 Rs. -

viii For depth above 4.2m and up to 4.8m No 60.00 Rs. -

Page 41 of 109

Sr.


49

Providing sand cast iron drop connection externally for 60

cm drop from branch sewer line to main sewer manhole

including inspection and cleaning eye with chain and lid,

sand cast iron drop pipe and bend encased all-round with

cement concrete 1:5:10 (1 cement : 5 fine sand : 10

graded stone aggregate 40 mm nominal size) with all

centring and shuttering required, cutting holes in walls

and making good with brick work in cement mortar 1:4 (1

cement : 4 coarse sand) plastered with cement mortar 1:3

(1 cement : 3 coarse sand) on inside of the manhole wall

lead caulked joints between sand cast iron pipes and

ittings, stiff cement mortar 1:1 (1 cement : 1 fine sand)

joints between sand cast iron tee and S.W. pipe, making

required channels complete as per standard design and

specifications :

i 150 mm dia. sand cast iron drop connection each 10.00 Rs. -

50Extra for depths beyond 60 cm of sand cast iron drop

connection complete :

i For 150 mm dia. sand cast iron drop connection meter 22.00 Rs. -

Page 42 of 109

Sr.


51

Providing and constructing brick masonry chamber for

underground C.I. inspection chamber and bends with well

burnt modular clay bricks crushing strength not less than

35kg/cm² in cement mortar 1:4 (1 cement : 4 coarse sand)

C.I. cover with frame (light duty) 455x610 mm internal

dimensions, total weight of cover with frame to be not

less than 38 kg (weight of cover 23 kg and weight of

frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2

coarse sand : 4 graded stone aggregate 20 mm nominal

size) foundation concrete 1:5:10 (1 cement : 5 fine sand :

10 graded stone aggregate 40 mm nominal size), inside

plastering 12 mm thick with cement mortar 1:3 (1 cement

: 3 coarse sand) finished smooth with a floating coat of

neat cement on walls and bed concrete etc. complete as

per standard design :

iInside dimensions 600x850 mm and 45 cm deep for pipe

line with three or more inlets Each 363.00 Rs. -

52

Brick work with modular fly-ash lime bricks (FaLG Bricks)

confirming to IS:12894-2002 of class designation 4.0 in

foundation and plinth in:

i Cement Mortar 1:6 (1 cement : 6 coarse sand) cum 230.96 Rs. -

53

Providing and making 15mm thick cement plaster on the

rough side of single or half brick wall of mix: all complete


Engineer.

i In Cement Mortar 1:4 (1 cement : 4 fine sand) Sqm 71.80 Rs. -

Page 43 of 109

Sr.


ii In Cement Mortar 1:6 (1 cement : 6 fine sand) Sqm 1,035.00 Rs. -

54

Providing orange colour safety foot rest of minimum 6

mm thick plastic encapsulated as per IS : 10910 on 12mm

dia steel bar conforming to IS : 1786 having minimum

cross section as 23 mmx25mm and over all minimum

length 263 mm and width as 165mm with minimum 112

mm space between protruded legs having 2 mm tread on

top surface by ribbing or chequering besides necessary

and adequate anchoring projections on tail length on 138

mm as per standard drawing and suitable to with stand

the bend test and chemical resistance test as per

specifications and having manufacture's permanent

identification mark to be visible even after fixing,

including fixing in manholes with 30x20x15 cm cement

concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded

stone aggregate 20 mm nominal size) complete as per

design.

Each 8.00 Rs. -

55

Providing and fixing in position precast circular 560mm

internal dia SFRC/R.C.C. manhole cover or cover and

frame of approved quality:

i Cover and frame H D - 20 Each 2.00 Rs. -

56

Providing and fixing on wall face or under floor UV

stabilized Unplasticised Rigid PVC pipes (single socketed)

having 3.2mm wall thickness conforming to IS : 13592

(4kg/sqcm) including required couplers, jointing with seal

ring conforming to IS : 5382 leaving 10 mm gap for

thermal expansion etc complete.

Page 44 of 109

Sr.


i 75 mm dia pipe. metre 6.00 Rs. -

57

Providing and fixing on wall face UV stabilized

Unplasticised - PVC moulded fittings/ accessories having

3.2mm wall thickness for Rigid PVC pipes conforming to IS

: 13592 (heavy) jointing with seal ring conforming to IS :

5382 leaving 10 mm gap for thermal expansion.

a Vent covel

i 75 mm Each 2.00 Rs. -

58

Providing and constructing soak pit 1.20x1.20x1.20m

filled with brickbats including S.W. drain pipe 100 mm

diameter and 1.20 m long complete as per standard

design.

Each 6.00 Rs. -

59

Supplying and laying following size RCC Hume pipe class

NP-2 (in standard length of 2 metre) with collar in ground

below road, path etc at a depth not less than 50 cm and

upto 90cm including excavation, dismantling of road if

required and refilling the trench with excavated material,

ramming and making the surface good etc. as required.

i 300 mm dia. R.C.C. pipe Rmt 140.00 Rs. -

Page 45 of 109

Sr.


ii 200 mm dia. R.C.C. pipe Rmt 3,606.00 Rs. -

iii 150 mm dia. R.C.C. pipe Rmt 1,896.00 Rs. -

iv 100mm dia. R.C.C. pipe Rmt 855.00 Rs. -

60

Providing, Laying and jointing non-pressure (NP3) RCC

socket & spigot pipes with rubber gasket joint including

testing of joints. [Conforming to IS ; 458-1988, ISI marked

laying as per IS 783:1985)

i 450 mm dia Meter 6,720.00 Rs. -

ii 600 mm dia Meter 8,132.00 Rs. -

iii 900 mm dia Meter 1,850.00 Rs. -

iv 1000 mm dia. Meter 703.00 Rs. -

Page 46 of 109

Sr.


61

Providing and laying Reinforced Cement Concrete pipe NP

3 /prestressed concrete pipe on first class bedding.

(Laying Reinforced cement concrete pipe NP3

/prestressed concrete pipe for culverts on first class

bedding of granular material including fixing collar with

cement mortar 1:2 but excluding bedding below

pipes,excavation, protection works, backfilling, concrete

and masonry works in head walls and parapets . ) all



i 450 mm dia Rmt 948.00 Rs. -

ii 600 mm dia Rmt 30.00 Rs. -

iii 1000 mm dia Rmt 507.00 Rs. -

62

Providing and fixing cast iron grating for gully trap. all



i 3000x150mm square Each 966.00 Rs. -

Page 47 of 109

Sr.


63

Supplying and laying ISI marked double wall HDPE pipe (IS

14930 Part II) having corrugation on the outer wall and

plan surface on inner wall in ground below road, path etc

at a depth not less than 40 cm and upto 90 cm including

excavation, dismantling of road if required and refilling

the trench with excavated material, ramming and making

the surface good etc. as required. all complete as per


i 200 mm outer dia Meter 84,195.00 Rs. -

ii 120 mm outer dia Meter 1,04,910.00 Rs. -

64

Providing and fixing un-polished 45mm to 50mm thick

RAJIM SAND STONE laid on drainage wall top for the base

of drain slab, as per drawing and as per direction of

Engineer complete etc.

sqm. 11,785.00 Rs. -

65

Providing and laying Pitching on slopes laid over prepared

filter media including boulder apron laid dry in front of

toe of embankment complete as per drawing and

Technical specifications as per section 2504

i Stone/Boulder Cum 814.80 Rs. -

Page 48 of 109

Sr.


66

Excavation for Structures (Earth work in excavation of

foundation of structures as per drawing and technical

specification, including setting out, construction of

shoring and bracing, removal of stumps and other

deleterious matter, dressing of sides and bottom and

backfilling with approved material.) all complete as per


a Ordinary Soil

i Upto 3 m depth cum 2,855.90 Rs. -

ii 3 m to 6 m depth cum 1,010.72 Rs. -

67

Back filling behind abutment, wing wall and return wall

complete as per drawing and Technical specification

710.1.4 of I.R.C. 78 and 2200. all complete as per


i Granular material cum 2,255.53 Rs. -

Page 49 of 109

Sr.


68

Providing and laying of Filter media with granular

materials/stone crushed aggregates satisfying the

requirements laid down in clause 2504.2.2. of MoRTH

specifications to a thickness of not less than 600 mm with

smaller size towards the soil and bigger size towards the

wall and provided over the entire surface behind

abutment, wing wall and return wall to the full height

compacted to a firm condition complete as per drawing

and technical specifications 710.1.4 of I.R.C. 78 and 2200

cum 154.70 Rs. -

69

Providing and laying Plain/Reinforced cement concrete in

sub-structure complete as per drawing and technical

specifications section 1500, 1700 and 2200 all complete


Engineer.

a Height upto 5m

i Using concrete Mixer

ii P.C.C. Grade M-15 cum 68.36 Rs. -

70

Providing and laying Plain/Reinforced cement concrete in


specifications section 1500, 1700 and 2200

a Height upto 5m

i Using concrete Mixer (R.C.C. Grade M-30) cum 860.70 Rs. -

71

Furnishing and Placing Reinforced/Prestressed cement

concrete in super-structure as per drawing and Technical

Specification sections 1500, 1600 and 1700 all complete


Engineer.a RCC Grade M 30

For Solid Slab Super Structure

Page 50 of 109

Sr.


Using Concrete Mixer

i Height upto 5m cum 215.48 Rs. -

72

Providing and laying M-30 grade Reinforced cement

concrete approach slab including reinforcement and

formwork complete as per drawing and Technical

specification and as per relevant sections 1500, 1600,

1700 and 2704 all complete as per technical


cum 69.15 Rs. -

73

PCC M15 Grade leveling course below approach slab

complete as per drawing and Technical specification and

as per relevant section 2700 all complete as per technical


cum 23.21 Rs. -

74

Construction of precast RCC railing of M30 Grade,

aggregate size not exceeding 12 mm, true to line and

grade, tolerance of vertical RCC post not to exceed 1 in

500, centre to centre spacing between vertical post not

to exceed 2000 mm, leaving adequate space between

vertical post for expansion, complete as per approved

drawings and technical specifications as per relevant

clauses of section 1500, 1600, 1700 and 2703 (vide

drawing No. SD/202, SD/304) all complete as per


meter 51.00 Rs. -

75

Supplying, fitting and placing un-coated HYSD bar

reinforcement in foundation complete as per drawing and

technical specifications as per section 1600.

MT 34.04 Rs. -

Page 51 of 109

Sr.


76

Supplying, fitting and placing HYSD bar reinforcement in


specifications section 1600 and 2200

MT 95.06 Rs. -

77

Supplying, fitting and placing HYSD bar reinforcement in

super-structure complete as per drawing and technical

specifications

MT 32.32 Rs. -

78Providing and fixing in position tar paper bearing for slab

as per approved drawings and specificationsqm 750.98 Rs. -

79 Filler joint

i

Providing & fixing 2 mm thick corrugated copper plate (

12 m long x 25 cm wide ) in expansion joint complete as

per drawing & Technical Specification.

sqm 4.42 Rs. -

ii

Providing & fixing 20 mm thick compressible fiber board (

12 m long x 25 cm deep ) in expansion joint complete as

per drawing & Technical Specification.

sqm 8.84 Rs. -

iii

Providing and fixing in position 20 mm thick premoulded

joint filler ( 12 m long x 30 cm deep ) in expansion joint

for fixed ends of simply supported spans not exceeding 10

m to cater for a horizontal movement upto 20 mm,

covered with sealant complete as per drawing and

technical specifications.

sqm 13.26 Rs. -

iv

Providing and filling joint sealing compound ( 12 m long x

100 mm wide x 10 mm deep recess) as per drawings and

technical specifications with coarse sand and 6% bitumen

by weight

sqm 13.26 Rs. -

Page 52 of 109

Sr.


80Drainage Spouts complete as per drawing and Technical

specifications of section 2705each 20.40 Rs. -

81

Providing plain cement concrete M 15 in footpaths

including centring and shuttering all complete as per

drawing and Technical Specification Section 1500 & 1700.

cum 35.36 Rs. -

82

Providing and laying Filter material underneath pitching

in slopes complete as per drawing and Technical

specification including trimming of slopes to proper

profile and preparation of bed as per section 2504

cum 30.60 Rs. -

83

Providing weep holes in Brick masonry/ Plain/ Reinforced

concrete abutment, wing wall/return wall with 100 mm

dia AC pipe, extending through the full width of the

structure with slope of 1V :20H towards drawing foce.

Complete as per drawing and Technical specifications

section 2706 and 2200

meter 22.10 Rs. -

84

Providing and laying Cement concrete wearing coat M-

30 grade including reinforcement complete as per

drawing and Technical Specifications

cum 126.48 Rs. -

85

Cast in Situ Cement Concrete M20 kerb (Construction of

cement concrete kerb with top and bottom width 115 and

165 mm respectively, 250 mm high in M 20 grade PCC on

M-10 grade foundation 150 mm thick, foundation having

50 mm projection beyond kerb stone, kerb stone laid with

kerb laying machine, foundation concrete laid manually,

all complete as per clause 408)

meter 51.00 Rs. -

Page 53 of 109

Sr.


86

Providing & filling 37/40 mm. wide expansion joint

between spans in wearing coat with premoulded joint

filler, primer coat and joint sealing compound as per

MOST standard drawing and specifications as per section

2600 in:-

i R.C.C. 75 mm deep wearing coat metre 25.50 Rs. -

87

Painting on kerbs in black and yellow alternate bands

including cost of material and labour complete as per

drawings and specifications as per clause 803.

i With Road Marking Paint metre 51.00 Rs. -

88

Surface dressing of the ground including removing

vegetation and making up undulations and in-equalities

not exceeding 15 cms in depth/ height including disposal

of rubbish upto 1.5 m lift and lead upto 50m (at least 5m

away from the dressed area).

Sqm 56,445.00 Rs. -

89

Footpaths and Separators (Construction of

footpath/separator by providing a 150 mm compacted

granular sub base as per clause 401 and 75 mm thick

cement concrete base with PCC grade M-15, over laid

with precast cement concrete tiles 25mm thick fixed in

20mm thick cement mortar 1:3 including provision of all

drainage arrangements but excluding kerb channel

excluding cost of GSB.) as per clause 410.

Sqm 2,480.00 Rs. -

Page 54 of 109

Sr.


90

Providing and fixing kerb stones 100 mm thick and 600

mm wide chisel dressed cut stones fixed in CC 1:3:6 (block

size 250 x 225 mm) including all excavation. all complete


Engineer.

metre 2,480.00 Rs. -

91

Random rubble masonry with hard stone in foundation

and plinth in Cement Mortar 1:6 (1 Cement : 6 Coarse

Sand) including leveling up with cement concrete 1:6:12

(1 cement : 6 coarse sand: 12 stone aggregate 20mm

nominal size) upto plinth level.

Cum 739.71 Rs. -

92

Random rubble masonry with hard stone in foundation

and plinth in Cement Mortar 1:6 (1 Cement : 6 Coarse

Sand) including leveling up with cement concrete 1:6:12

(1 cement : 6 coarse sand: 12 stone aggregate 20mm

nominal size) upto plinth level.

i

Extra for random rubble masonry with hard stone in

superstructure above plinth level for every floor or part

thereof in addition to rate for foundation and plinth:

Cum 555.05 Rs. -

Page 55 of 109

Sr.


93

Pointing on stone work with cement Mortar 1:3 (1

cement : 3 fine sand) all complete as per technical


i Ruled pointing Sqm 2,200.80 Rs. -

94

Steel work welded in built up sections/ framed work

including cutting,hoisting, fixing in position and applying a

priming coat of red oxide zinc chromate primer. all



iIn gratings, frames, guard bar, ladder, railings, brackets,

gates and similar works.Kg 831.60 Rs. -

95

MS Grill: Providing and fixing M.S. grill of approved

pattern made of M.S. flats or square or round bars

welded to steel frame of windows etc. including applying

a priming coat welded to frame with all necessary fitting

complete including applying a priming of red oxide zinc

chromate primer. all complete as per technical


Kg 10,146.00 Rs. -

96

15 mm thick Table rubbed polished Granite stone slab

flooring laid over 20mm (Average) thick base of cement

mortar 1:4 (1 cement : 4 coarse sand) laid and jointed

with grey cement slurry including rubbing and polishing

etc. complete. (Area of slab should be 0.50 sqm and

above)

`

i Granite stone grey/pink sqm 44.40 Rs. -

Page 56 of 109

Sr.


97Painting on new work (two or more coats) to give an even

shade with:

iSatin synthetic enamel paint (top most approved branded

quality) sqm 3,134.88 Rs. -

98

Providing and fixing G.I. chain link fabric fencing of

required width in mesh size 50x50 mm including

strengthening with 2 mm dia wire or nuts, bolts and

washers as required complete as per the direction of

Engineer-in-charge.

i Made of G.I. wire of dia 4 mm Sqm 3,116.40 Rs. -

Page 57 of 109

Sr.


99

Planting Permanent Hedges including Digging of Trenches

(Planting permanent hedges including digging of trenches,

60 cm wide and 45 cm deep, refilling the excavated earth

mixed with farmyard manure, supplied at the rate of 4.65

cum per 100 meters and supplying and planting hedge

plants at 30 cm apart), including maintenance of one

year. all complete as per technical Specifications and as

per direction of Engineer.

No. 858.00 Rs. -

100

Planting of Trees and their Maintenance for one Year. all



(Planting of trees by the road side (Avenue trees) in 0.60

m dia. holes, 1 m. deep dug in the ground, mixing the soil

with decayed farm yard/sludge manure, planting the

saplings, backfilling the trench, watering, fixing the tree

guard and maintaining the plants for one year) all



Nos 1,006.00 Rs. -

101

Tree Guard with MS Angle Iron and Steel Wire (Providing

and fixing tree guard 0.60 meter square, 2.00 meter high

fabricated with MS angle iron 30 x 30 x 3 mm, MS iron 25

x 3 mm at 100mm centre to centre and steel wire 3 mm

dia. welded and fabricated as per design in two halves

bolted together, fixed in ground with P.C.C M-10 of

dimensions 150x150x200mm.)

Each 399.00 Rs. -

Page 58 of 109

Sr.


102

Providing and planting following herbs in garden including

preparation of soil, earth mixed with manure or sludge in

the ratio of 2:1 by volume (2 parts of stacked volume of

earth after reduction by 20% :1 part of stacked volume of

manure after reduction by 8%) watering, dressing

including removal of rubbish and surplus earth,

preparation of base plantation, providing and spreading

different fertilizers, soil and sand if any with all leads and

lifts including cost of manure, sludge or extra good earth

if needed and deweeding and as per instruction of

Engineer in charge

Page 59 of 109

Sr.


i Dhoob grass Sqm 16,996.90 Rs. -

ii Carpet grass Sqm 7,891.90 Rs. -

103

Supplying, Installation, Testing and Commissioning of

"Circular Swing" play equipment : The leg support , top

bar and swing frame is made from powder coated ‘A’

class GI pipes. two seats are made out of molded plastic

including all material, labour, accessories and

commissioning all complete as per the direction of

engineers in charge and Technical Specification.

No. 3.00 Rs. -

104


"Toddler Swing" play equipment : The toddler swing the

center support is made up of GI pipes. Between the two

horizontal bars there is a heavy-duty metal clamp

attached to it including all material, labour, accessories

and commissioning all complete as per the direction of


No. 6.00 Rs. -

105


"MultiSeater See-Saw" play equipment : The MS See saw

comprises four FRP seats. The lever is consisted of

powder coated GI pipes and bearing is heavy duty nylon

bush type including all material, labour, accessories and



No. 6.00 Rs. -

Page 60 of 109

Sr.


106


"Standered See-Saw" play equipment : The standard see

saw is a good entertainer for the children. The lever of the

see – from moulded plastic including all material, labour,

accessories and commissioning all complete as per the

direction of engineers in charge and Technical

Specification.

No. 6.00 Rs. -

107

P/ Instalation of Dust Bin. Height = 0.6m. Dia. = 0.3m.

Dustbin is especially designed for accommodating well as

wet kind of trash. cylinder of the bin is fabricated out of

Aluminium perforated sheet 300mm in diameter and

380mm long with a self-closing tilt able lid. The drum is

mounted on nylon bearings to provide it with complete

rotation of the drum to facilitate the garbage removal.

The frame of dustbin is made up of 25NB powder coated

GI pipes including all material, labour, accessories and


engineers in charge .

No. 37.00 Rs. -

Rs. - Sub Total of Utility Services

Page 61 of 109

Sr. No Description of Item Unit

Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR

C

I

1 33 KV RMU

a

Supplying, Receiving, Storage, Installation, Testing and

Commissioning of approved make Motorized type Ring Main

Unit (extendible type) for out door installation, rated for 36KV,

50Hz, 630A, STR of 25kA for 1sec with SF6 insulation having 2

sets of three positon Load break Switch with earthing switch as

Incomer and 1 set of three position Load break Switch with

earthing switch for Tee-off. The units shall be complete with

interconnections of both Power & Control, accessories, hardwares

etc as required for completeness and as per direction of engineer,

attached specification, CSPDCL standards and Elecrical

Inspectorate Standards.

The accessories shall include:

3 Set of ON/ OFF and Phase indicating lamps

3 Nos end termination kit for 3 core XLPE cable

Set 2.0 Rs. -

2

Supplying and laying following sizes one number XLPE, steel

armoured, aluminium conductor power cable of 33 KV grade in

existing RCC/ HUME/ STONEWARE/ METAL/HDPE pipe as

required..

a 3Cx400 sqmm mtr 100.0 Rs. -

Bill of Quantity


33 KV Power supply to Phase-I works at sector-12, sector-40 and other Specified areas at Naya Raipur

ELECTRICAL WORKS



b 3C X 300 sqmm mtr 6500.0 Rs. -

c 3C X 120 sqmm mtr 100.0 Rs. -

3

Supplying and making indoor cable end termination with heat

shrinkable jointing kit complete with all accessories including

lugs suitable for following size of 3 core, XLPE aluminum

conductor cable of 33 KV grade as required :

a 400 sqm Each 1.0 Rs. -

b 300 sqmm Each 4.0 Rs. -

c 120 sqmm Each 1.0 Rs. -

4

Supplying and making outdoor cable end termination with heat






a 300 sqmm Each 2.0 Rs. -


5

Supplying and making straight through cable jointing with heat


ferrules suitable for following size of 3 core, XLPE aluminum




6

Supplying and laying of 50mm x 6mm GI earth strip along with

the 33kV cable and making connection with steel supports enroute

and connecting firmly with the earthing systems of end stations

complete with ferrules, other accessories, hardwares etc as

required for completeness and as per direction of engineer,

attached specification, CSPDCL standards and Elecrical

Inspectorate Standards.

mtr 500.0 Rs. -



7

Providing and fixing HT Danger Notice Plate of 250 mm x 200

mm 2mm thick, made of mild steel and vitreous enamelled white

on both sides and inscription in signal red colour on front side as

per IS:2551 with accessories, hardwares etc as per direction of

engineer, CSPDCL standards and Electrical inspectorate

standards.

Each 2.0 Rs. -

8

Construction of plinth for , RMU in RM-15 RCC construction for

installation of RMU including excavation, laying of PCC, neatly

dressed, plastered, supply of all materials as required for

completeness, as per attached specification/ drawing, CSPDCL

standards and direction of EIC.

cum 65.0 Rs. -

9

Supply, Installation, Testing & Commissioning of indoor, floor

mounted 33 KV switchboard comprising of the 2 number vertical

panels with draw type VCB rating 1600 A , 36 KV, 25 kA shall

be act as outgoing panel with CT ratio of 400/200/5 amp and will

be connected with existing panel in substation. The panel shall

have Static Energy Meters, O/C and E/F relay, auxiliary relays

etc.The panel shall confirm 61850 protocol & as per CSPDCL


Set 1.0 Rs. -

II

10 11 KV RMU

(a)

Supply, Installation, Testing & Commissioning of floor mounted

SF6, motorized type RMU (extendible type) comprising of 2 nos.

12 kV, 630 A LBS for loop in and loop out to form ring main

system and 1 no VCB unit shall controlled distribution transformer

complete with accessories, hard wares etc. as required for

completeness as per attached specification/ drawing, CSPDCL


Set 2.0 Rs. -

11KV System to Phase-I works at sector-12, sector-40 and other Specified areas at Naya Raipur



(b)








Set 3.0 Rs. -

(c)

Supply, Installation, Testing & Commissioning

of floor mounted Oil type RMU (extendible type) comprising of 2

nos. 12 kV, 630 A LBS for loop in and 1 no fuse unit shall

controlled distribution transformer complete with accessories, hard

wares etc. as required for completeness as per attached

specification/ drawing, CSPDCL standards and direction of EIC.

Set 3.0 Rs. -

11

Supplying and laying following sizes one number XLPE, steel



required..

a 3Cx240 sqmm mtr 9415.0 Rs. -

c 3C X 120 sqmm mtr 400.0 Rs. -

d 3Cx 95 sqmm mtr 1600.0 Rs. -



e 3C X 70 sqmm mtr 1600.0 Rs. -

12

Supplying and making outdoor cable end termination with heat







d 70 sqmm Each 2.0 Rs. -

13

Supplying and making indoor cable end termination with heat









d 70 sqmm Each 3.0 Rs. -

14

Supplying and making straight through cable jointing with Heat

Shrinkable Jointing Kit complete with all acessories including

ferrule suitable for following size of 3 core, XLPE aluminum







15

Supply and fixing of 11 kV Danger plates as per specification of

Discom on the existing poles complete in all respect as per

Discom specification.

Each 18.0 Rs. -

16

Supply, Installation, Testing & Commissioning of indoor, floor

mounted 11KV switchboard comprising of the 3 number vertical

panels with draw out type VCB rating 800 A 12KV, 18.4kA

shall be act as out going panel with CT ratio of 200/100/5 amp and

will be connected with existing panel in substation . The panels

shall have Static Energy meter, O/C and E/F relay etc. The

panel shall confirm 61850 protocol & as per CSPDCL standards

and direction of EIC.

Set 2.0 Rs. -

17


Outdoor type package substation with facility for internal lighting,

earthing, padlocks etc.Connection between RMU & transformer

will be by Aluminium bus bar and connections from transformer to

LT ACB. Package Substations will have following equipment.

1. HT side Non extensible 12 kv 630 RMU having SF6/Air

insulation with 2 nos. LBS and 1 nos VCB for transformer

protection having fault rating of 25KA for 1 Sec.

2. 11/.433 Kv 500 KVA Oil type Transformer having doubled

wound copper winding with A Class insulation.

3. LT Side having 800 amp ACB with O/C,E/F protection and

having 4 nos 250 amp MCCB for outgoing. The equipment shall

be SCADA compatible having communication port and having

provision of DT Metering within it, completeness as per attached


nos 5.0 Rs. -



III

18

Designing and providing suitable RCC foundation for 7 metre to 12

metre high GI octagonal pole including steel reinforcement

(minimum 90kg per cum), form work, embeding 2 nos 50mm dia

PVC pipe for cable entry in each foundation, excavation disposal

of surplus soil and curing etc. as required.

Cum 705.00 Rs. -

19

Supply of hot dipped galvanized (in single dip to average 65

micron) octoganal pole made of 3mm thick steel sheet having

window and flush cover with locking arrangement at suitable

height from base for cable termination block, pole suitably

reinforced with welded steel section at window cut section tomake

the strength of pole unaffected, with following minimum

specifications including 3mm thick anchor plate, 4 nos 20mm dia

foundation bolts of EN8 grade. (designed for wind speed upto

180km/hr)

a7 metre high, dia 130mm at bottom and 70mm at top, base

plate size 220x220x12mm, foundation bolts 700mm longEach 518.00 Rs. -

b6 metre high, dia 130mm at bottom and 70mm at top, base

plate size 220x220x12mm, foundation bolts 600mm longEach 285.00 Rs. -

20

Supply of hot dipped galvanized (in single dip to average 70

micron) octoganal pole made of 4mm thick steel plate having base

plate 275x275x16mm, window and flush cover with locking

arrangement at suitable height from base for cable termination

block, pole suitably reinforced with welded steel section at window

cut section to make the strength of pole unaffected, including

template and anchor plate 270x270x3mm with 4 nos 750mm long,

24mm dia foundation bolts (EN8 grade).(designed for wind speed

upto 180km/hr)

Street Lightning to Phase-I works at sector-12, sector-40 and other Specified areas at Naya Raipur



a 9 metre high, minimum dia 155 mm at bottom and 70 mm at top Each 440.00 Rs. -

4

Erection of GI octogonal pole on existing cement concrete

foundation having grouted bolts and nuts, aligning in true vertical

position as required.

a 6 meter high Each 285.00 Rs. -

b 7 meter high Each 518.00 Rs. -

c 9 metre high Each 440.00 Rs. -

21

Supply and fixing following street light pole bracket on existing

pole made out of 50 mm dia MS "B" class pipe welded to 300 mm

long MS pole canopy of suitable dia at a angle of 102.50 including

having MS triangular stiffner of size 150 X 50 X 5 mm thick,

making arrangement for tightening the bracket with pole by

providing suitable size heavy duty nuts and bolts in canopy,

painting with one coat of approved steel primer etc. as required.

a Single Over Hang 1.00 metre Long Each 285.00 Rs. -



b Single Over Hang 1.50 metre Long Each 690.00 Rs. -

c Double Over Hang 1.50 metre Long Each 226.00 Rs. -

d Double Over Hang 1.00 metre Long Each 40.00 Rs. -

22

Supplying, installation, testing and commissioning of following

230/250 volts LED street light fitting with all accessories like

driver, heat sink made of die cast aluminium with IP 66 protection

and 5 KV surge protection on pole bracket complete as required.

a Not More than 40 Watt Each 285.00 Rs. -

b Not More than 65 Watt Each 626.00 Rs. -

c Not More than 90 Watt Each 288.00 Rs. -



d Not More than 120 Watt Each 320.00 Rs. -

Design, Fabrication, Supply, Erection, Testing and commisioning

of Powder coated, Weather Proof Double door type Feeder pillar

fabricated out of 14 guage CRCA sheet steel in cubical, free

standing, dust and vermin proof, with reinforcement of suitable

size angle iron, channel, T -iron or flats as required. Feeder pillar

shall be treated with all anti-corrosive process before painting as

per specification. Feeder Pillar shall be suitable for 415V, 3-Phase,

Four wire, 50 Hz supply complete with earth bus and lifting hooks

as required in case of large panels.Approval shall be taken for

each panel before fabrication. (All hardwares like nuts and bolts

used shall be Galvanized and Zinc passivated)

Rs. -

INCOMER

1No. 4 Pole 100A TPN MCCB (35 KA)

1No. 100A FP Contactor, AOM switch & Timers for 24 Hrs. setting

Metering & Indication

1 set of phase indicating lamps

BUS-BAR

1 Set of 100A TPN Aluminium Bus Bar with colour coded PVC

SleevesOUTGOINGS

24 Nos. 32A SP MCB

GPRS MODULE FOR AUTOMATION

24

Earthing with G.I. earth pipe 3.0 mtr long, 40 mm dia including

accessories, and providing masonry enclosure with cover plate

having locking arrangement and watering pipe etc. with charcoal

and salt as required.

Set 1287.00 Rs. -

25

Supplying and laying double wall HDPE pipe having corrugation

on the outer wall and plan surface on inner wall in ground below

road, path etc at a depth not less than 40 cm including excavation,

dismantling of road if required and refilling the trench etc. as

required.

23 Set 14.00



a 40 mm mtr 40016.00 Rs. -

b 90 mm mtr 500.00 Rs. -

26

Supplying and laying following sizes one number PVC insulated,

PVC sheathed, steel armoured, aluminium conductor power

cable of 1.1 KV grade in existing RCC/HUME/STONE

WARE/METAL/HDPE pipe required.

a 2x6 sq.mm mtr 1000.00 Rs. -

b 4x10 sq.mm mtr 2000.00 Rs. -

c 4 x16 sq. mm. mtr 41500.00 Rs. -

d 3.5 x 25 sq. mm. mtr 2800.00 Rs. -



e 3.5 x 50 sq. mm. mtr 3700.00 Rs. -

f 3.5 x 70 sq. mm. mtr 4000.00 Rs. -

27

Supplying and making end termination with brass compression

gland and aluminum lugs for following size armoured aluminum

conductor power cable of 1.1 KV grade as required.

a 2x6 sq.mm Each 10.00 Rs. -

b 4x10 sq.mm Each 15.00 Rs. -

c 4 x 16 sq. mm. Each 300.00 Rs. -

d 3.5 x 25 sq. mm. Each 52.00 Rs. -



e 3.5 x 50 sq. mm. Each 30.00 Rs. -

f 3.5 x 70 sq. mm. Each 25.00 Rs. -

28

Supplying, fixing and cramping suitable size and all type

aluminium ferule/ lugs to following size 1.1 KV grade power

cable core/ lead, pressed with high pressure cramping tool

including connection to switch gear/ MCCB etc as required.

a 2X6 sq.mm Each 50.00 Rs. -

b 4X10 sq.mm Each 100.00 Rs. -

c 4 x 16 sq. mm. Each 12000.00 Rs. -

d 3.5 x 25 sq. mm. Each 280.00 Rs. -



e 3.5 x 50 sq. mm. Each 155.00 Rs. -

f 3.5 x 70 sq. mm. Each 50.00 Rs. -

29

Supply and drawing following sizes of FR PVC insulated copper

conductor, single core cable in the existing surface/ concealed,

steel/ PVC conduit as required.

a 3 x 1.5 sq.mm. (from Pole Junction box to Light fitting) mtr 14000.00 Rs. -

Rs. -

30

Supplying erection testing and commissioning of hot dipped

galvanised (single dip 86 micron) 20 metre High mast pole on

RCC foundation with all accessories and equipments,

detailed as below to withstand wind pressure upto 180km/hr

and minimum following specifications:

a) HM shaft made of not more than 2 sections of suitable

lengths with telescopic stressfit joints between sections without

any circumpherencial welding, sheet thickness 4mm top and

bottom sections, nominal dia 460mm on bottom and 150 mm on

top, base plate 30mm thick 670mm dia, PCD of foundation

bolts 650mm.

b) Double drum winch for lowering & raising of lantern carriage

on high mast with operatable with power tool/ manual handle

attachment with a torque limiting device for safe locking of

carriage.

c) Raising/lowering type lantern carriage designed to carry

specified nos of luminaries, control gear box, junction box.

d) Top pulley assemble with weather proof cover.

Each 12.00



31

Supplying, fixing, testing and commissioning of following 230/250

volts metal halide lamps on High mast pole

etc as required

Each 132.00 Rs. -

32

Supplying and making straight through joint with heat

shrinkable joint kit including aluminium ferrules for following

size of PVC insulated and PVC sheathed / XLPE aluminum

conductor cable of 1.1 KV grade as required.

Rs. -

a 3.5 x 70 sq. mm. Each 9.00 Rs. -

b 3.5x50 sq .mm Each 6.00 Rs. -

IV

33








No. 12.00 Rs. -

Power supply for Street light to Phase-I works at sector-12, sector-40 and other Specified areas at Naya Raipur



34

Supply Installation, testing & commissioning of 11/ 0.433 KV,

315KVA distribution transformer with off load tap changer,

copper wound, oil cooled suitable for outdoor use with required

fittings, accessories,both side cable terminal box, hardwares etc.

as required for completeness as per attached

specification/drawing, CSPDCL standards and direction of EIC.

Nos 2.00 Rs. -

35

Supply Installation, testing & commissioning of 11/ 0.433 KV, 100

KVA distribution transformer with off load tap changer, AL wound,

oil cooled suitable for outdoor use with required fittings,

accessories,both side cable terminal box, hardwares etc. as

required for completeness as per attached specification/drawing,

CSPDCL standards and direction of EIC.

Nos 14.00 Rs. -

36

Supply Installation, testing & commissioning of outdoor, structure

mounted, LT DB rated for 415v, 450 A, 4 wires with copper bus

bars, 1no. 450 A, 25 kA, 4 P MCCB as incomer, 3nos. 125 A ,4 P

MCCB as outgoing feeder with supporting structure, accessories,

hardwares etc. as required for completeness as per attached


Nos 12.00 Rs. -

37

Supplying and laying of following one number XLPE, steel



required for completeness, as per attached specification/ drawing,

CSPDCL standards and direction of EIC

a 3x70 sqm Mtrs 9840.00 Rs. -

b 3x120 sq mm Mtrs 2000.00 Rs. -



Rs. -

38

Supplying and making INDOOR cable end jointing with heat

shrinkable cable jointing kit including lugs and other jointing

materials, for following size of 3 core, XLPE aluminum

conductor cable of 11 KV grade as required for completeness as

per attached specification/ drawing, CSPDCL standards and

direction of EIC.

a 3x70 sqm Nos. 30.00 Rs. -

b 3x120 sq mm Nos. 2.00 Rs. -

39

Supplying and making STRAIGHT THROUGH cable jointing

with heat shrinkable cable jointing kit including ferrule and other

jointing materials, for following size of 3 core, XLPE aluminum

conductor cable of 11 KV grade as required

nos

a 3x70 sqm 17.00 Rs. -

b 3x120 sq mm 3.00 Rs. -



40

Supply of all materials, installation, testing and commissioning of

GI pipe electrode as per IS: 3043 comprising of 40mm dia,

2.9mm thick, 3m long class A GI pipe with flange, 16nos. 12mm

dia through holes buried in a pit. The scope shall cover excavation

in all kinds of soil and rock, filling the pit with equal proportion of

salt and charcoal in layers of 300mm depth, 150mm wide alround

the pipe from bottom upto a depth of 300mm below the masonary

chamber, refilling by excavated soil free from rock and shark

edges; provision of watering arrangement with GI funnel and wire

mesh be enclosed in a brick masonary chamber of 400mm x

400mm x 400mm with removable RCC cover on top. The

connection from the flanges of the pipe shall be established by

50mm x 6mm GI strip using 12mm dia GI hardwares. The work

shall be carried out with accessories, hardware etc as required for

completeness and as per attached specification/drawing, CSPDCL


Nos. 30.00 Rs. -

41

Supply, running and terminating of GI materials as earth

continuity conductor to earth all the metallic parts/ neutral of

transformer/ lightning arrestors, control room equipments to earth

electrodes with accessories, hardwares etc. as required for

completeness, as per attached specification/ drawings, CSPDCL


a 50mm x 6mm strips mtrs 160.00 Rs. -

b 8 SWG wires mtrs 150.00 Rs. -

c 0 SWG wires mtrs 120.00 Rs. -



42

Supplying and erecting MS gate of approx. size 3.0 m (W) x

2.0 m (H) in two laps for electric sub-station switch yard

fencing frame made of angle iron size 50 X 50 X 6 mm on top

bottom and sides fitted with flat iron support of size 25 X 6 mm

on mid way horizontaly and square bar of size 8 mm at every

100mm vertically including 3 sets of heavy duty MS hinges

and aldrop complete duly painted with one coats of red oxide

and two coats of approved colour paint.

Sqm 60.00 Rs. -

43

Supplying and erecting chain link mesh fencing for electric

sub-station switch yard of 2.5 m approx. height from ground

level using angle iron size 50 X 50 X 6 mm erected in C.C.

foundation 15 X 15 X 40 cm deep at every 2 metre fitted with

flat iron support of size 25 X 6 mm on top, bottom and mid

way and chain link mesh 50 x 50 mm aparture and 4 mm dia

G.I. hard wire securing and screwing with 2mm dia G.I. wire,

G.I. staples, G.I.U-nails or steel pins to the angle iron at every

distance of 30 cms, by iron studs complete duly painted with

one coats of red oxide and two coats of approved colour paint.

sqm 348.00 Rs. -

44

Horizontal drilling: Horizontal directional drilling along roads for

laying XLPE HT/ LT, UG cable, for communication cable along

with suitable HDPE Duct at various locations as pointed out by

departmental officers, includes Survey of site information

collection regarding underground utilities, sensing of utilities by

sensing equipment, pit making, pilot drilling, pre-reaming pulling

HDPE duct of suitable size in single roll, pulling HT/ LT UG cable

through installed HDPE duct, providing barricades and necessary

signal lights, closing of pits with excavated earth including cost of

HDPE pipe, consolidating pit are, including road

restoration/supervision departments, cost of all materials, labour,

conveyance, hire charges etc. complete preparation of pit by

excavated soil/ hard morum & refilling compacting surface as it is

position / horizontal drilling across road for cable laying propose

with disturbing present installation as per instruction, Guide line

Detail technical specifications as per direction of Engineer in

charge

rmt 1150.00 Rs. -



V

45

Townguide Post top luminaire - Integral LED post top luminaire

with two layer optics, IP 66, IK10, and effective system lumen

output of more than 3000 lumens. The Fixture has clear bowl with

CRI greater than 80 & CCT Natural day light & warm light. Housing

is high pressure die cast aluminium with PU paint for higher

reliability. L70 life of the LED is more than 50000 burning hours.

The fixture is provided with 3 m height mild steel & hot dip

galvanised pole primered and painted with polyurethane. The pole

has a flush door at teh bottom with provision for loop in & loop out.

nos 12.00 Rs. -

46

BBG 151, LED marker light for directional guidance made from

high pressure die cast aluminium housing and IP 67, IK10, with

toughened glass diffuser. The product should e not more than 3 W

with lumens output of more than 35 lumens. It should be CCE, CE

& RohS compliant in 3000 K. The outer casing should be in

stainless steel. L70 life of the fixture should be more than 25000

burning hours.

nos 16.00 Rs. -

47

BWG 150, Integral recessed LED wall light luminaire with high

pressure die cast aluminium body & polycarbonate diffuser. The

fixture is IP67 & IK10. The system wattage is 4 W and lumen

output is more than 35 lumens. The fixture is CCE, CE & RoHS

compliant. Size for the same should be 145 mm X 145 mm X 105

mm

nos 12.00 Rs. -

48

Color Burst PC,Integral Die cast aluminium body with powder

coated finish, 30 W RGB LED floodlight. The fixture is IP66, Class

2 Led product, UL, cUL, CE & PSE compliant. It should be

compatible with full range of Philips controllers Including LSM or I -

player. It should have clear tempered lens with 10 degree beam

abgle. The L70 life of the fixture with 3 RGB channels on should

be more than 55000 burning hours.

nos 18.00 Rs. -

Green Area Lighting to Phase-I works at sector-12, sector-40 and other Specified areas at Naya Raipur



49

Data enabler Pro - Power / Data supplies DMX Ethernet - Integral

power / data enabler housed in IP66 high pressure die cast

aluminium housing , IP66, with maximum load capacity of 16

amps.

nos 20.00 Rs. -

50

Iplayer 3 - Compact DMX control solution with advanced Software

functionality with light show authorising software for dynamic color

changing effects. The controller has removable secure digital card

drive of 256 MB and has two DMX 512 Rj45 ports.ontrol Gear

Box,IP54 for housing contol component and other complete

accessories like cable tie, joining,splitter etc

nos 15.00 Rs. -

51

BCP 151, Integral LD bollard luminaire 800 mm in length, with

extruded aluminium body & polycarbonate difuser. The fixture is

IP65/ IK10.

nos 15.00 Rs. -

Sub Total of Electrical Works Rs. -

D) Auto Taxi Stand



D Auto and Taxi Stand

1

Excavation for all types and sizes of foundations, trenches and drains or

for any other purpose including disposal of excavated stuff upto 1.5 m lift

and lead upto 50m (at least 5m away from the excavated area), including

dressing and leveling of pits.

In all types of soils.

A Depth of excavation up to 1.5 m Cum 1088.96 Rs. -

2

Filling from available excavated stuff (Excluding rock) in trenches, plinth,

sides of foundation etc. in layers not exceeding 20cm in depth

consolidating each deposited layer by ramming and watering with a lead

upto 50 M. and lift upto 1.5 M.

cum 35.15 Rs. -

3

Providing and filling in plinth with sand/ Crusher dust and hard moorum

under floor in layers not exceeding 20cm in depth consolidating each

deposited layer by ramming and watering, including dressing etc.

complete.

Cum 11.90 Rs. -

4

Providing and fixing form work including centring, shuttering, strutting,

staging, propping bracing etc. complete and including its removal at all

levels, for:

aFoundations, footings, bases of columns plinth beam, curtain wall in any

shape and size and all type of wall below plinth level.sqm 37.13 Rs. -

Bill of Quantity


85 of 109

D) Auto Taxi Stand

bWindow sills, anchor blocks, string course, bends, copings, bed plates and

like.sqm 3.44 Rs. -

cSuspended floors, roofs, access platform, balconies (plain surfaces) and

shelves (cast in situ)sqm 78.03 Rs. -

5

Clearing and grubbing road land including uprooting rank

vegetation, grass, bushes, shrubs, saplings and trees girth up to

300 mm, removal of stumps of trees cut earlier and disposal of

unserviceable materials and stacking of serviceable material to

be used or auctioned up to a lead of 1000 meters including

removal and disposal of top organic soil not exceeding 150 mm

in thickness if required and as per relevant clauses of section-

200.

a In area of light jungle ha 0.16 Rs. -

6

Providing and laying nominal mix plain cement concrete with crushed

stone aggregate using concrete mixer in all works upto plinth level

excluding cost of form work.

a1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm

nominal size).Cum 24.88 Rs. -

b1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40mm


86 of 109

D) Auto Taxi Stand

c1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm


7

Providing and laying design mix reinforcement cement concrete with crushed

graded stone aggregate 20mm nominal size using batching plant, transit

mixer and concrete pump, in all works upto floor five level excluding cost of

reinforcement and form work.

a M-25 (using minimum cement content 410 kg/cum concrete) Cum 7.80 Rs. -

8

Providing and laying pre-stressed cement concrete of M-35 grade in

superstructure including form work but excluding reinforcement complete

as per drawing and specifications and IS : 1343-2012.

Cum 23.04 Rs. -

9

Providing and placing in position reinforcement for R.C.C. work including

straightening, cutting, bending, binding etc. complete as per drawings

including cost of binding wire in foundation and plinth all complete

a Thermo-Mechanically treated bars FE 500D Kgs 2634.93 Rs. -

10

Construction of embankment with Material Obtained from

Borrow Pits/Borrow Area (Construction of embankment with

approved material/selected soil having C.B.R. (as specified

in the contract) obtained from borrow pits with all lifts

and leads, transporting to site, spreading, grading to required slope

and compacting to meet requirement of table 300-2)

Cum 790.50 Rs. -

11 Granular Sub-base as per Table:- 400-1

87 of 109

D) Auto Taxi Stand

Construction of granular sub-base by providing graded Material, ,

carriage of mixed Material to work site, spreading in uniform layers

with motor grader on prepared surface watering, rolling and

compacting with vibratory power roller at OMC to achieve the desired

density, complete as per clause 401(i) Grading (iii)

a Plant mix method (with Mechanically crushed stone only) 189.24 Rs. -

12

Dry Lean Cement Concrete Sub-base as per IRC:SP-49

(Construction of dry lean cement concrete Sub-base over a prepared

sub-grade with coarse and fine aggregate conforming to IS: 383, the

size of coarse aggregate not exceeding 26.5 mm, aggregate cement

ratio not to exceed 15:1, aggregate gradation after blending to be as

per table 600-1, cement content not to be less than 150 kg/cum,

optimum moisture content to be determined during trial length

construction, concrete strength not to be less than 10 Mpa at 7 days,

mixed in a batching plant, transported to site, laid with a paver with

electronic sensor, compacting with 8-10 tonnes vibratory roller,

finishing and curing as per clause 601.)

Cum 172.30 Rs. -

a

13

Footpaths and Separators (Construction of footpath/separator by

providing a 150 mm compacted granular sub base as per clause 401

and 75 mm thick cement concrete base with PCC grade M-15, over

laid with precast cement concrete tiles 25mm thick fixed in 20mm

thick cement mortar 1:3 including provision of all drainage

arrangements but excluding kerb channel excluding cost of GSB.) as

per clause 410.

Sqm 348.60 Rs. -

14

Random rubble masonry with hard stone in foundation and plinth in

Cement Mortar 1:6 (1 Cement : 6 Coarse Sand) including leveling up with

cement concrete 1:6:12 (1 cement : 6 coarse sand: 12 stone aggregate

20mm nominal size) upto plinth level.

Cum 90.14 Rs. -

15

Random rubble masonry with hard stone in foundation and plinth in

Cement Mortar 1:6 (1 Cement : 6 Coarse Sand) including leveling up with

cement concrete 1:6:12 (1 cement : 6 coarse sand: 12 stone aggregate

20mm nominal size) upto plinth level.

88 of 109

D) Auto Taxi Stand

a

Extra for random rubble masonry with hard stone in superstructure above

plinth level for every floor or part thereof in addition to rate for foundation

and plinth:

Cum 17.25 Rs. -

16

Cement Concrete Pavement (Construction of un-reinforced, dowel

jointed, plain cement concrete pavement over a prepared sub-base,

coarse and fine aggregate conforming to IS:383, and graded as per

table 600-3, mixed as per approved mix design at site, laid, spread,

vibrated, compacted and finished in a continuous operation including

provision of contraction, expansion, construction and longitudinal

joints, joint filler, separation membrane, sealant primer, joint sealant,

de-bonding strip, dowel bar, tie rod, admixtures as approved, curing

compound, finishing to lines and grades as per drawing as per clause

602.)

a With Cement concrete grade M-40 and minimum cement content @ 400 kg/cum.Cum 149.76 Rs. -

17Coursed rubble masonry (Second sort) with hard stone in Cement mortar

1:6 (1 cement : 6 coarse sand) upto plinth level.Cum 33.97 Rs. -

18Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to

IS:12894-2002 of class designation 4.0 in foundation and plinth in:

a Cement Mortar 1:4 (1 Cement : 4 Coarse Sand) Cum 6.62 Rs. -

19

Cast in Situ Cement Concrete M20 kerb (Construction of cement

concrete kerb with top and bottom width 115 and 165 mm

respectively, 250 mm high in PCC M20 grade on PCC M10 grade

foundation 150 mm thick, foundation having 50 mm projection

beyond kerb stone, kerb stone laid with kerb laying machine,

foundation concrete laid manually, all complete as per clause 409)

Meter 232.00 Rs. -

89 of 109

D) Auto Taxi Stand

20 Painting on Concrete Surfaces

aTwo coats on new surfaces (Painting two coats after filling the surface with

synthetic enamel paint in all shades on new plastered concrete surfaces)sqm 116.00 Rs. -

21

Providing and fixing factory made UPVC door frame made of UPVC profile

section having an overall dimension as below (tolerance ± 1mm) with

wall thickness 2.0mm ± 0.2mm, corners of the door frame to be jointed

with galvanized brackets and stainless steel screws, joints mitred and

plastic welded. The hinge side vertical of the frames reinforced by

galvanized M.S. tube of size 19 X 19mm and 1mm ± 0.1mm wall

thickness and 3 nos. stainless steel hinges fixed to the frame complete as

per manufacturers specification and direction of Engineer-in-charge

a Extruded section Profile size 48x40 mm. metre 12.00 Rs. -

22

Providing and fixing factory made PVC door shutters of specified

thickness made of styles and rails of a UPVC hollow section of specified

size 59x24 mm and wall thickness 2 mm ± 0.2 mm with inbuilt edging on

both sides. The styles and rails mitred and joined at the corners by means

of M.S. galvanised/ plastic brackets of size 75x220 mm having wall

thickness 1.0 mm and stainless steel screws.

a 24 mm thick door shutters with styles and rails of size 59x24 mm sqm 3.20 Rs. -

23

Steel work in tubular (round, square or rectangular hollow tubes etc.)

structure in built-up sections, trusses and frame work including cutting,

hoisting, fixing in position upto a height of 5m above plinth level,

consisting of columns trusses, roof and bottom purlins, base plate, holding

down bolts, wind ties bracing (if required), bolts, nuts and washers for

fastening etc. complete with applying a priming coat of red oxide zinc

chromate primer.

90 of 109

D) Auto Taxi Stand

a Electric resistance or induction butt welded tubes Grade-250 kg 4174.79 Rs. -

24

Steel work welded in built up sections/ framed work including cutting,

hoisting, fixing in position and applying a priming coat of red oxide zinc

chromate primer.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar

works.

a Angle 65x65x6 @ 5.0kg/m kg 2240.00 Rs. -

25

Supplying and fixing rolling shutter of approved makes made of M.S. laths

interlocked together through their entire length and jointed together at the

end by end locks, mounted on specially designed pipe shaft with brackets,

side guides and arrangements for inside and out side locking with push

and pull arrangement complete but excluding the cost of top cover and

spring.

a 80x1.25mm M.S. Laths sqm 31.50 Rs. -

26

Providing and fixing in position chain linked steel wire fabric made of 4mm

dia G.I. wire of required width in mesh to concrete/ wooden/ angl eiron posts

including securing and screwing with 2mm dia G.I. wire, G.I. staples, G.I.U-

nails or steel pins etc., complete.

a Aperture 50x50mm sqm 168.00 Rs. -

91 of 109

D) Auto Taxi Stand

27

Providing and fixing 12mm thick pre-laminated particle board flat pressed

with decorative lamination and balancing lamination on specified sides

exterior Grade – I MDF Board 12 mm thick confirming to IS:14587,

including fixed in aluminium doors, windows shutters and partition frames

with C.P. brass/ stainless steel screws etc. complete

a With decorative lamination on both side Sqm 2.52 Rs. -

28

Providing & fixing UV stabilized fibreglass reinforced plastic (FRP) sheet

roofing upto any pitch including fixing with polymer coated 'J' or 'L' hooks,

bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding

the cost of purlins, rafters, trusses etc. The sheets shall be manufactured

out of 2400 TEX panel rovings incorporating minimum 0.3% Ultra-violet

stabiliser in resin system under approximately 2400 psi and hot cured.

They shall be of uniform pigmentation and thickness without air pockets

and shall conform to IS 10192 and IS 12866.The sheets shall be opaque

or translucent, clear or pigmented, textured or smooth as specified.

a2mm thick corrugated (2.5" or 4.2" or 6") or step-down (2"or 3"or 6") as

specified.sqm 161.20 Rs. -

29 Providing and making 12mm thick cement plaster of mix:

a In Cement Mortar 1:4 (1 cement : 4 fine sand) Sqm 194.91 Rs. -

30

Planting of Trees and their Maintenance for one Year

(Planting of trees by the road side (Avenue trees) in 0.60 m dia.

holes, 1 m. deep dug in the ground, mixing the soil with decayed

farm yard/sludge manure, planting the saplings, backfilling the

trench, watering, fixing the tree guard and maintaining the plants

for one year)

Each 36.00 Rs. -

92 of 109

D) Auto Taxi Stand

31Providing and making pointing on stone work with cement Mortar 1:3 (1

cement : 3 fine sand)

a Ruled pointing Sqm 272.76 Rs. -

32

Planting Permanent Hedges including Digging of Trenches

(Planting permanent hedges including digging of trenches, 60 cm

wide and 45 cm deep, refilling the excavated earth mixed with

farmyard manure, supplied at the rate of 4.65 cum per 100 meters

and supplying and planting hedge plants at 30 cm apart.)

Rmt 90.00 Rs. -

33

Providing and laying ceramic glazed floor tiles conforming to IS : 15622

of approved size, make, colour, shade laid on 20 mm thick Cement

Mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with

white cement mixed with matching pigment etc., complete

a Size 300x300mm sqm 6.75 Rs. -

34

15 mm thick Table rubbed polished Granite stone slab flooring laid over

20mm (Average) thick base of cement mortar 1:4 (1 cement : 4 coarse

sand) laid and jointed with grey cement slurry including rubbing and

polishing etc. complete. (Area of slab should be 0.50 sqm and above)

a Granite stone black Sqm 8.00 Rs. -

35

Stone work with KOTA STONE Slab (machine cut edge) exposed face

machine cut and table rubbed with rough backing for wall lining etc.

(Veneer work) upto 10 metre height, backing filled with a grout of 20 mm

thick cement mortar 1:3 (1 cement: 3 coarse sand), jointing with cement

mortar 1:2 (1 cement: 2 stone dust) with admixture of pigment matching

the stone shade including rubbing and polishing complete. (To be secured

to the backing by means of cramps which shall be paid separately)

93 of 109

D) Auto Taxi Stand

a 25mm thick Sqm 51.15 Rs. -

36 Distempering with acrylic washable distemper to give an even shade

a On new work (Two or more coats) Sqm 201.21 Rs. -

37 Painting on new work (two or more coats) to give an even shade with:

a Satin synthetic enamel paint sqm 168.00 Rs. -

38

Providing and fixing vitreous china water closet (European type W.C.

pan) with white ISI marked plastic seat and lid, 10 litre low level white

P.V.C. flushing cistern (same colour), conforming to IS : 7231, with all fittings

and fixtures complete including cutting and making good the

walls and floors wherever required :

a White pedestal type each 2.00 Rs. -

39Providing and fixing white vitreous china urinal basin with waste fitting

as per IS : 2556, and other couplings in C.P. brass complete:

a Flat back half stall urinal of size 460x380x250mm each 2.00 Rs. -

94 of 109

D) Auto Taxi Stand

40Providing and fixing white vitreous china wash basin including making

all connections but excluding the cost of fittings :

a White Size 550x450 mm each 2.00 Rs. -

41Providing and fixing vitreous china pedestal for wash basin completely

recessed at the back for the reception of pipes and fittings.

a White each 2.00 Rs. -

42

Providing and fixing on wall face or under floor UV stabilized Unplasticised

Rigid PVC pipes (single socketed) having 3.2mm wall thickness conforming

to IS : 13592 (4kg/sqcm) including required couplers, jointing with seal ring

conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc

complete.

a 75 mm dia pipe metre 30.00 Rs. -

b 110 mm dia metre 10.00 Rs. -

43

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded

fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes

conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS :

5382 leaving 10 mm gap for thermal expansion.

95 of 109

D) Auto Taxi Stand

a Tee/ Tee with door/ Bend 45°/ Bend 90°

75 mm Nos. 1.00 Rs. -

b Double "Y" with or without door

75 mm Each 1.00 Rs. -

c Vent covel

110 mm Nos. 1.00 Rs. -

d Access door cap

75 mm Each 2.00 Rs. -

e 110 mm Each 2.00 Rs. -

96 of 109

D) Auto Taxi Stand

f P trap 110mmx110mm long Nos. 1.00 Rs. -

g Nahani trap 110x75mm Nos. 1.00 Rs. -

44

Providing and placing on terrace (at all floor levels) polyethylene water

storage tank ISI : 12701 marked with cover and suitable locking

arrangement and making necessary holes for inlet, outlet and overflow

pipes but without fittings and the base support for tank

a 2 nos of tank @ 1000 Liter each litre 2000.00 Rs. -

45

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having

thermal stability for hot & cold water supply including all CPVC plain & brass

threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This

includes jointing of pipes & fittings with one step CPVC solvent cement and

testing of joints complete as per direction of Engineer in Charge.

a 20 mm nominal outer dia .Pipes. metre 30.00 Rs. -

b 32 mm nominal outer dia .Pipes. metre 20.00 Rs. -

97 of 109

D) Auto Taxi Stand

c 40 mm nominal outer dia .Pipes. metre 10.00 Rs. -

46Providing and fixing 15 mm nominal bore Brass bib/stop cock of

approved quality:

a Bib cock (250 grams) each 3.00 Rs. -

b Stop cock (350 grams) each 2.00 Rs. -

47

Constructing masonry Chamber 60x60x75 cm, inside with modular well

burnt clay bricks of 35 kg/ cm² in cement mortar 1:4 (1 cement : 4 coarse

sand) for sluice valve, with C.I. surface box 100mm. top diameter, 160

mm bottom diameter and 180 mm deep (inside) with chained lid and RCC

top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate

20mm nominal size) necessary excavation foundation concrete 1:5:10 (1

cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size)

and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand)

12 mm thick finished with a floating coat of neat cement complete as per

standard design :

each 2.00 Rs. -

48

Providing, lowering, laying, aligning, fixing in position at and jointing at all

level/ depths ISI marked HDPE pipes of PE-100 grade and PN 6 for sewer

application as per IS 14333-1996 (amended upto date) in trenches in

complete including all material, labour, testing and commissioning as per


Note : E/w to be measured and paid separately.

a 200 mm dia Rmt 50.00 Rs. -

98 of 109

D) Auto Taxi Stand

49

Providing and fixing M.S. flat iron tree guard 60cm dia. and 2m height

above ground level formed of 4 nos. 25x6mm and 8 nos. 25x3mm vertical

M.S. flats riveted to 3 nos. 25x6mm M.S. flat iron rings in two halves,

bolted together with 8mm dia. and 30mm long bolts including painting two

coats with paint of approved brand and manufacture over a coat of

priming, complete in all respects.

Nos 36.00 Rs. -

50

Supply of hot dipped galvanized (in single dip to average 70 micron)

octoganal pole made of 4mm thick steel plate having base plate

200x200x12mm, window and flush cover with locking arrangement at

suitable height from base for cable termination block, pole suitably reinforced

with welded steel section at window cut section to make the strength of pole

unaffected, including template and anchor plate 240x240x3mm with 4 nos

450mm long, 16mm dia foundation bolts bolts (EN8 grade).

a 5 metre high, minimum dia 129mm at bottom and 75mm at top Each 8.00 Rs. -

51

Supply and fixing following street light pole bracket on existing pole made

out of 50 mm dia MS "B" class pipe welded to 300 mm long MS pole canopy

of suitable dia at a angle of 102.50 including having MS triangular stiffner of

size 150 X 50 X 5 mm thick, making arrangement for tightening the bracket

with pole by providing suitable size heavy duty nuts and bolts in canopy,

painting with one coat of approved steel primer etc. as required.

a Single Over Hang 0.75 metre Long Each 8.00 Rs. -

52Erection of GI octogonal pole on existing cement concrete foundation

having grouted bolts and nuts, aligning in true vertical position as required.

99 of 109

D) Auto Taxi Stand

a 5 metre high Each 8.00 Rs. -

53

Designing and providing suitable RCC foundation for 5m metre high GI

octagonal pole including steel reinforcement (minimum 90kg per cum), form

work, embeding 2 nos 50mm dia PVC pipe for cable entry in each

foundation, excavation disposal of surplus soil and curing etc. as required.

(size: 400 x 400 x 1200mm)

cum 6.00 Rs. -

54

Supplying ,installation ,Testing & Commissioning of 25W IP65 LED

streetlight Luminaire complete with pressure die cast aluminum housing.

The fixture shall be designed so as to have lumen maintenance of at least

70% at the end of 50,000 hours.

each 8.00 Rs. -

55

Supply and drawing following sizes of FR PVC insulated copper conductor,

single core cable in the existing surface/ concealed, steel/ PVC conduit as

required.

a 3x1.5 sq.mm. (from Pole Junction box to Light fitting) Mts 50.00 Rs. -

56

Supplying and fixing SP MCB, 240 volts, 'B' series, suitable for lighting and

other loads in the existing MCB DB complete with connections, testing and

commissioning etc. as required.

a SPMCB 10 A inside the box for cable connection Each 8.00 Rs. -

57

Supplying and laying double wall HDPE pipe having corrugation on the

outer wall and plan surface on inner wall in ground below road, path etc at a

depth not less than 100 cm excluding excavation, dismantling of road if

required and refilling the trench etc. as required.

100 of 109

D) Auto Taxi Stand

a 40 mm Outer dia. mtr 300.00 Rs. -

58Supplying and fixing of following sizes PVC conduit along with accessories

in surface complete as required.

a 20 mm mtr 250.00 Rs. -

59

Earthing with GI earth pipe 4.5 mtr long, 40 mm dia including accessories,

and providing masonry enclosure with cover plate having locking

arrangement and watering pipe etc. with charcoal and salt as required.

Nos. 4.00 Rs. -

60

Supplying and laying 6 SWG G.I. Wire at 0.50 meter below ground level for

conductor earth electrode, including soldering, excavation and refilling the

trench etc. as required.

mtr 70.00 Rs. -

LT Panel-Utility

Fabrication, supply, installation, testing and commissioning of cubicle type

compartmentalized wall/ floor mounted power cum control panel board of

specified size and 900mm (NS) deep made out of not less than 2 mm thick

CRCA MS sheet with suitable size compartments for bus bars, switchgears

and necessary cutouts for voltmeters, ameters ets as per specifications

including powder coating painting but without busbars, switchgears and other

accessories etc complete as required for completeness and as per attached

specification, direction of Engineer, CGPWD standards and Electrical

Inspectorate standards. (Only face area is to be measured)

Rs. -

INCOMER

1 No. 100A FP MCCB(35 KA)

Metering & Indication

1 set of phase indicating lamps

1 set of (0-500V) Voltmeter with VSS

1 set of (0-100A) Ammeter with ASS with 3 no s.100/5A CTs

BUS-BAR

1 Set of 100A TPN Aluminium Bus Bar with colour coded PVC Sleeves

OUTGOINGS

61set 1.00

101 of 109

D) Auto Taxi Stand2 Nos. 32A TPN MCCB (35KA) ,3 Nos 32 A SP MCCB (35KA)

1 No.32 A DP contactor ,AOM switch & 24 hrs setting

62

Supplying and laying following sizes one number XLPE, steel armoured,

aluminium conductor Power cable of 1.1 KV grade in existing RCC/ HUME/

STONEWARE/ METAL pipe as required for completeness and as per

attached specification, direction of Engineer, CGPWD standards and

Electrical Inspectorate standards.

a 3.5 x 50 sq. mm. Mtr. 70.00 Rs. -

b 4x25 sq.mm Mtr. 100.00 Rs. -

c 2 x 10 sq. mm. Mr. 150.00 Rs. -

63

Supplying and making end termination with brass compression gland and

aluminum lugs for following sizes armoured aluminium conductor power

cable of 1.1KV grade along with accessories, hardwares etc as required for

completeness and as per attached specification, direction of Engineer,

CGPWD standards and Electrical Inspectorate standards.

Mtr.

a 3½ X 50 sq. mm Each 3.00 Rs. -

61set 1.00

102 of 109

D) Auto Taxi Stand

b 4x25 sq.mm Each 2.00 Rs. -

c 2 x 10 sq. mm. Each 18.00 Rs. -

64

Point Wiring for light/ fan/ exhaust fan/ call bell point with 1.5 sqmm FR

PVC insulated stranded copper conductor single core cable in concealed

PVC conduit, with 5 amp modular switch, modular base and cover plate,

suitable size G.I. box and earthing the point with same size cable along with

accessories, hardwares etc as required for completenessand as per

attached specification, direction of Engineer, CGPWD standards Electrical

Inspectorate standards

a Short Point Point 15.00 Rs. -

b Medium Point Point 10.00 Rs. -

c Long Point Point 5.00 Rs. -

103 of 109

D) Auto Taxi Stand

65

Point wiring for light plug point with 2 x 2.5 sq mm FR PVC insulated

stranded copper conductor single core cable cable in concealed PVC conduit

along with modular type 6 amp switch and 3 pin 6 amps socket outlet with

modular base and cover plate, suitable size G.I. box, earthing the switch box

and socket outlet with same size cable along with accessories, hardwares

etc. as required for completenessand as per attached specification, direction

of Engineer, CGPWD standards and Electrical Inspectorate standards.

a Medium Point Point 6.00 Rs. -

66

Circuit/ sub main wiring along with earth wire with the following sizes of FR

PVC insulated copper conductor, single core cable in concealed PVC

conduit along with accessories, hardwares etc. as required.for completeness

and as per attached specification, direction of Engineer, CGPWD standards

and Electrical Inspectorate standards.

a 3 X 1.5 sq. mm in 20mm conduit Mtr. 50.00 Rs. -

b 3 X 2.5 sq. mm in 20mm conduit Mtr. 15.00 Rs. -

67

Wiring for light/ fan/ exhaust fan / call bell point with 1.5 sqmm FR PVC

insulated stranded copper conductor single core cable in surface PVC

conduit, with 5 amp piano type switch, phenolic laminated sheet, suitable

size M.S. box and earthing the point with same size cable etc as required.

Mtr.

a Medium Point Point 5.00 Rs. -

104 of 109

D) Auto Taxi Stand

b Long Point Point 5.00 Rs. -

68

Extra for providing and fixing light plug point on board in surface PVC conduit

point wiring with piano type 3 pin 5 amp socket outlet and 5 amp switch

including cost of phenolic laminated sheet and M.S. box etc. as required.etc.

as required.

Point 10.00 Rs. -

69

Wiring for circuit/ sub main wiring along with earth wire with the following

sizes of FR PVC insulated copper conductor, single core cable in surface

PVC conduit etc as required.

Point

a 3 X 1.5 sq. mm in 20mm conduit 20.00 Rs. -

70

Supplying and fixing metal box of following sizes (nominal size) in recess

with suitable size phenolic laminated sheet cover in front including painting

etc as required.

a 150 mm X 150 mm X 60 mm deep Mtr 10.00 Rs. -

71

Supplying and fixing following size/ modules GI box with modular base &

cover plate for modular switches in recess etc. as required for competeness



105 of 109

D) Auto Taxi Stand

a 125mmX75mm (4 Module) Each 15.00 Rs. -

72

Supplying and fixing modular stepped type electronic fan regulator (two

module size) moving all rounds on the existing modular plate and switch box

including connections but excluding modular plate etc. as required.

Each 6.00 Rs. -

73

Supplying and fixing 3 pin, 5 amp ceiling rose of approved make and ISI

quality on the existing metal box including connections along with

accessories, hardwares etc as required for competeness and as per

attached specification, direction of Engineer, CGPWD standards and

Electrical Inspectorate standards.

Each 6.00 Rs. -

74

Supplying and fixing polycarbonate batten/ angle holder of approved make

and ISI quality including connections along with accessories, hardwares etc

as required for competeness and as per attached specification, direction of

Engineer, CGPWD standards and Electrical Inspectorate standards.

Each 6.00 Rs. -

75

Providing and fixing round/ hexagonal fan box (125mm dia) depth 75mm

(max.) with 12mm dia steel bar hook, 1.6mm thick MS sheet cover, in RCC

slab along with accessories, hardwares etc as required for competeness



Each 6.00 Rs. -

76

Supplying, installation, testing and commissioning of following sizez ceiling

fan of approved make and ISI quality including the down rods of 30 cm

wiring with1.5 sq. mm FR PVC insulated, copper conductor, single core

cable, earthing, connections along with accessories, hardwares etc as

required for completeness and as per attached specification, direction of


a 1050 mm sweep Each 5.00 Rs. -

106 of 109

D) Auto Taxi Stand

b 1200 mm sweep Each 1.00 Rs. -

77

Supplying, installation, testing and commissioning of following sizes exhaust

fan (heavy duty) of approved make and ISI quality in existing opening in wall

including earthing, connections along with accessories, hardwares etc as

required for competeness and as per attached specification, direction of


`

a 300 mm sweep Each 2.00 Rs. -

78Supplying, installation, testing and commissioning of following surface LED

light

a

18watt LED Tube Light Fixture

1x18watt T8 LED tube 4 ‘ length made of full polycarbonate housing with

integral driver suitable for retrofitting in an existing luminaire mounted on

decorative batton. Rating of tube 18 W + 10% , 240 V , 50 Hz. Operating

voltage : 140-280 V . Terminal should be suitable for wiring from one side

only . Lumen output ≥1900 Lumens. Colour temperature 6500K + 200 , CRI

≥ 80 , System efficacy ≥ 100 lm/W. Driver efficiency ≥ 85 % , AthD < 15% ,

Pf ≥ 0.95. Driver protection : Open circuit, Short circuit, Reverse polarity,

Surge protection : 2.5 kV, High Temperature. LED is LM 80 certified and

LM79 report is Certified by NABL Accredited lab. LED tube is also RoHS &

CE rated.

Each 15.00 Rs. -

79supplying ,fixing ,testing and commissioning of follwing CFL in existing

lighting luminaries as required

107 of 109

D) Auto Taxi Stand

a 15 Watt Each 5.00 Rs. -

80

Supplying and fixing on surface/ recess following way, 240 volts SP&N, MCB

distribution board consumer unit of sheet steel phosphatized and powder

painted complete with tinned copper busbar, neutral busbar, earth bar, din

bar, detachable gland plate, including interconnections, earthing etc. as

required. (But without MCB/ RCCB/ Isolator)

a 4 way, single door Each 7.00 Rs. -

81

Supplying and fixing SP MCB, 240 volts, 'C' series, suitable for inductive

loads in the existing MCB DB complete with connections, testing and

commissioning etc. as required.

a 6 amps to 32 amps Each 21.00 Rs. -

81

Supplying and fixing following rating, 240 volts TWO POLE

ISOLATOR in the existing MCB DB complete with connections,

testing and commissioning etc. as required

a 40 amps Each 7.00 Rs. -

108 of 109

D) Auto Taxi Stand

82 Design,Fabrication,supply,installation,testing and commissioning of pedestal mounted Block Main Power Board, made out of 2 mm thick CRCA sheet steel, cubicle type,FRLSee standing,dust/vermin/ weather proof with busbars, switchgears,earth bus etc including powder coated painting along with accessories,hardwares etc. required for completeness and as per attached specification, direction of Engineer, CGPWD standards and Electrical Inspectorate standards. The panel box shall house : 1 No 4 pole 63A isolator as Incomer ; 100A four pole Copper busbrs,6 Nos 16A SP MCB , C series, 10kA as outgoing feeders:6 Nos lockable compartments for housing kWh meters Interconnection by Copper insulated leads(DOUBLE DOOR TYPE)Each 1.00 Rs. -

Sub total of Auto Taxi Stand Rs. -

109 of 109

Documents

SECTOR 30, Integrated Infrastructure Development, Naya Raipur · NRDA F-1 NAYA RAIPUR DEVELOPMENT AUTHORITY Tender Document for the Integrated Infrastructure Development for phase