Upload
vukiet
View
215
Download
2
Embed Size (px)
Citation preview
Item no Long Item Description QTY UNIT RATE AMOUNT
A
Earthwork excavation in all kinds of soils, Soft murum,Hard
Murum, boulders for any kind of foundation, Footings of
columns, Raft, machine foundation, plinth beams , wall footing,
gutters, tanks Retaining walls, catch pits, Lift pits, trenches for
drains, pits and tunnels etc., for the following depths below
average ground level including shoring, strutting for protecting
the sides of foundation, pumping, baling of water so as to
keep foundations in dry conditions at any stage of work and
drain the water away from the site of work without any extra
payment, levelling, ramming the bottom of excavation and also
back filling (The proctor density of back filling should be 95% of
standard proctor)sides of foundation with selected excavated
earth in layers upto ground level including watering,
consolidation and carting away and disposing off the surplus
excavated earth at places shown within the site, unloading,
spreading, levelling as directed including all leads and lifts,
labour etc., all complete. If required, steel sheet soldier piling
and propping the earth using 20 - 25 mm thick wooden batten
in between the soldiers as directed by Engineer to protect the
sides of excavation which will be paid for separately under
relevant item. PCC size will be consider for measurement
The rate to include for extra earth work required for providing
shoring, strutting, steel soldier piling, working space etc. The
length and breadth of bottom of foundation and depth from top
of average ground level to bottom of foundation as shown
in the drawing or as directed only shall be measured for
payment irrespective of extra excavation done for steel soldier
piling and for working space for any kind of works including
water proof treatment works. Spec. NO. -NON DSR
1
Earthwork excavation in all kinds of soils, Soft murum,Hard
Murum, boulders for any kind of foundation, Footings of
columns, Raft, machine foundation, plinth beams , wall footing,
gutters, tanks Retaining walls, catch pits, Lift pits, trenches for
drains, pits and tunnels etc., for the Upto 1.50m depth
2,182.00 CUM
2
Earthwork excavation in all kinds of soils, Soft murum,Hard
Murum, boulders for any kind of foundation, Footings of
columns, Raft, machine foundation, plinth beams , wall footing,
gutters, tanks Retaining walls, catch pits, Lift pits, trenches for
drains, pits and tunnels etc., for the depth from 1.50- 3.00m
350.00 CUM
3
Earthwork excavation in all kinds of soils, Soft murum,Hard
Murum, boulders for any kind of foundation, Footings of
columns, Raft, machine foundation, plinth beams , wall footing,
gutters, tanks Retaining walls, catch pits, Lift pits, trenches for
drains, pits and tunnels etc., for the depth from 3.00 m to 4.50m
250.00 CUM
SCHEDULE OF QUANTITIES FOR PROPOSED CONSTRUCTION OF TEMPERATURE CONTROLLED WAREHOUSE AT
PATALGANGA MIDC, DIST- RAIGARH, MUMBAI.
Tender Ref. No.BL/LI/CC/MUM/16-17/CIVIL/02 Dated 21.06.16.
Earthwork excavation in soft rock, laterite, old cement
concrete & lime masonry for any kind of foundation, Footings of
columns, Raft, machine foundation, plinth beams , wall footing,
gutters, tanks Retaining walls, catch pits, Lift pits, trenches for
drains, pits and tunnels etc., for the following depths below
average ground level including shoring, strutting for protecting
the sides of foundation, pumping, baling of water so as to
keep foundations in dry conditions at any stage of work and
drain the water away from the site of work without any extra
payment, levelling, ramming the bottom of excavation and also
back filling (The proctor density of back filling should be 95% of
standard proctor)sides of foundation with selected excavated
earth in layers upto ground level including watering,
consolidation and carting away and disposing off the surplus
excavated earth at places shown within the site, unloading,
spreading, levelling as directed including all leads and lifts,
labour etc., all complete. If required, steel sheet soldier piling
and propping the earth using 20 - 25 mm thick wooden batten
in between the soldiers as directed by Engineer to protect the
sides of excavation which will be paid for separately under
relevant item. PCC size will be consider for measurement. Spec.
NO. -NON DSR
4
Earthwork excavation in soft rock, laterite, old cement concrete
& lime masonry for any kind of foundation, Footings of columns,
Raft, machine foundation, plinth beams , wall footing, gutters,
tanks Retaining walls, catch pits, Lift pits, trenches for drains,
pits and tunnels etc., for the following the depth from below
average ground level to 1.50m depth
618.00 CUM
5
Earthwork excavation in soft rock, laterite, old cement concrete
& lime masonry for any kind of foundation, Footings of columns,
Raft, machine foundation, plinth beams , wall footing, gutters,
tanks Retaining walls, catch pits, Lift pits, trenches for drains,
pits and tunnels etc., for the following the depth from below
1.50m to 3.00 m depth
350.00 CUM
6
Earthwork excavation in soft rock, laterite, old cement concrete
& lime masonry for any kind of foundation, Footings of columns,
Raft, machine foundation, plinth beams , wall footing, gutters,
tanks Retaining walls, catch pits, Lift pits, trenches for drains,
pits and tunnels etc., for the following the depth from below
3.00m to 4.50 m depth
250.00 CUM
Same as Item above but for excavation in Hard rock / boulders
(more than 1/2 Cum in size -Un poclainable) by chiseling/
wedging to required level for any kind of foundation, Footings
of columns, Raft, machine foundation, plinth beams , wall
footing, gutters, tanks Retaining walls, catch pits, Lift pits,
trenches for drains, pits and tunnels etc. to the required depth
including all leads and lifts, stacking excavated material within
plot at approved location and carting away unserviceable
material outside the site as directed, dressing, grading, cleaning,
excavating loose pockets and compacting them after backfilling
(The proctor density of back filling should be 95% of standard
proctor) as directed etc. as per detailed specification and
conforming to safety rules of Authority during the progress of
work. PCC size will be consider for measurement. Spec. NO. -
NON DSR
7
Same as Item above but for excavation in Hard rock / boulders
(more than 1/2 Cum in size -Un poclainable) by chiseling/
wedging to required level for any kind of foundation, Footings
of columns, Raft, machine foundation, plinth beams , wall
footing, gutters, tanks Retaining walls, catch pits, Lift pits,
trenches for drains, pits and tunnels etc. to the required depth
including all leads and lifts, for the depth upto 1.50 Mtr from the
average ground level
963.00 CUM
8
Same as Item above but for excavation in Hard rock / boulders
(more than 1/2 Cum in size -Un poclainable) by chiseling/
wedging to required level for any kind of foundation, Footings
of columns, Raft, machine foundation, plinth beams , wall
footing, gutters, tanks Retaining walls, catch pits, Lift pits,
trenches for drains, pits and tunnels etc. to the required depth
including all leads and lifts, for the depth from 1.50 Mtr to 3.00
Mtr depth.
450.00 CUM
9
Same as Item above but for excavation in Hard rock / boulders
(more than 1/2 Cum in size -Un poclainable) by chiseling/
wedging to required level for any kind of foundation, Footings
of columns, Raft, machine foundation, plinth beams , wall
footing, gutters, tanks Retaining walls, catch pits, Lift pits,
trenches for drains, pits and tunnels etc. to the required depth
including all leads and lifts, for the depth from 3.00 Mtr to 4.50
Mtr depth.
513.00 CUM
10
Cutting Mass Excavation for the plot development and
levelling in required development level (in soil, soft & hard
murum, soft rock, Hard rock, boulders ) including removing the
excavated stuff upto a distance of 1500 m beyond battery limit
area and stacking and /or spreading as directed, shoring,
strutting, dewatering wherever required & preparing the bed as
directed , including backfilling in layers, etc. complete. Spec. NO. -
NON DSR
3,300 CUM
11
Mass Filling with available excavated material in plot for plot
development with approved material wherever required,
including filling in layers of 20-30 cm., watering, compaction
levelling etc. complete. The proctor density of such compacted
fill shall be 95% of standard proctor. ( material to be approved
by engineer in charge ) including all royalties etc. complete.
Spec. NO. -NON DSR
3,113 CUM
12
Mass filling with contractor's locally available filling material
(murum) wherever required, including filling in layers of 20-30
cm., watering, compaction levelling etc. complete. The proctor
density of such compacted fill shall be 95% of standard proctor
with all leads and lifts brought from outside ( material to be
approved by engineer in charge ) including all royalties etc.
complete. Spec. NO. -NON DSR
3,303 CUM
13
Filling in plinth and floors with approved excavated
materials in 15cm to 20cm layers including watering and
compaction etc. complete.
Spec. No.: Bd-A 10 Page No. 262 (DSR -14- Raigadh Region)
671 CUM
14
Filling in plinth and floors with contractor's murum in 15 cm to
20 cm layers including watering, compaction etc. complete.
Spec. No.: Bd-A 11 Page No. 263 (DSR -14- Raigadh Region) 732 CUM
15
Providing & laying hard core of hand crushed metal 60 mm in
two layers of 100 mm each consolidated to 75 mm making total
thickness of 150 mm including watering ,ramming with heavy
rollers,levelling the surface with murum /gret spreading etc
.complete.(The rate shall be for compacted thickness.) Spec.
NO. -NON DSR
492 CUM
16
Dewatering the excavated trenches and pools of water in the
building area by using pumps of 3 H.P. Capacity and other
devices, including disposing of the water to a safe distance as
directed.
Spec. No.:Bd-A 9 Page No. 261 (DSR -14- Raigadh Region)
20 Hour
17
Dewatering the excavated trenches and pools of water in the
building area by using pumps of 5-9 H.P. Capacity and other
devices, including disposing of the water to a safe distance as
directed.
Spec. No.:Bd-A 9 Page No. 261 (DSR -14- Raigadh Region)
10 Hour
18
Providing and fabricating structural steel work in rolled
sections like joist, channels, angles, tees etc. as per detailed
design and drawings or as directed by Engineer-In-Charge.
including cutting, fabricating, hoisting, erecting, fixing in position
making riveted / bolted / welded connections with connecting
plates, braces etc. and including one coat of anticorrosive paint
and over it two coats of oil painting of approved quality and
shade etc. complete.
Spec. No.:Bd-C - 2 Page No. 275 (DSR -14- Raigadh Region)
3 MT
19
Providing and fixing stainless steel of S.S. 316
quality for railing with steel hand rail pipe of 50.80 mm dia of 18
gauge thickness witth steel pipe of 50.80 mm dia for vertical
post @ 1.20 metre centre to centre with bottom 75 mm dia
plates fixed on flooring with proper anchoring and middle
horizontal steel pipe rails of 15.87 mm dia of 18 gauge thickness
@ 150 mm centre to centre between top rail and flooring and
fixing the pipe to vertical post by steel adoptors including
finishing, grinding, gloossy polish fabrication and fixing as per
approved drawing and over all weight of steel railing shall not be
less than 7.5 kg per square meter etc. complete.
Spec - As directed by Engineer-In-Charge. (DSR -14- Raigadh
Region)
83 RMT
20
Providing and laying in situ cement concrete in proportion
______ of trap metal using 20 mm and down size coarse graded
machine crushed hard stone aggregate for foundation and
bedding, including bailing out water manually,formwork
compacting and curing etc. complete. Spec. No.:Bd-E -1
Page No. 287 (DSR -14- Raigadh Region)
344 CU.M
21
Providing and casting in situ cement concrete ___ of trap metal
using 20 mm and down size coarse graded machine crushed hard
stone aggregate for steps, including formwork, compacting,
roughening the exposed faces if special finish is to be provided
and curing etc. Complete. with all lead and lifts
Spec. No.:Bd-E -2 Page No. 288 (DSR -14- Raigadh Region)
5 CU.M
22
Providing and casting in situ cement concrete ____of trap metal
using 20 mm and down size coarse graded machine crushed hard
stone aggregate for coping to plinth or parapet, moulded or
chamfered as per drawings or As directed by Engineer-In-
Charge., roughening the exposed faces if special finish is to be
provided and curing etc. complete.
Spec. No.:BdE -3 Page No. 288 (DSR -14- Raigadh Region)
18 Cum
23
Providing and casting in situ cement concrete ____ of trap
metal using 20 mm and down size coarse graded machine
crushed hard stone aggregate for R.C.C.. work like raft, grillage,
strip, foundations and footing of R.C.C. Columns and steel
stanchions, including bailing out water manually, centering,
formwork, compacting, finishing and curing etc. complete.
(Excluding steel reinforcement) Spec. No.:Bd-F -3 Page No.
298 (DSR -14- Raigadh Region)
424 Cu. M
24
Providing and casting in situ cement concrete ____ of trap
metal using 20 mm and down size coarse graded machine
crushed hard stone aggregate for R.C.C. columns as per detailed
designs and drawings or As directed by Engineer-In-Charge.,
including centering, formwork, compacting,roughening the
surface if special finish is to be provided and curing etc.
complete. With all lead and lifts. (Excluding steel reinforcement)
Spec. No.:Bd-F -4 Page No. 298 (DSR -14- Raigadh Region)
139 Cu. M
25
Providing and casting in situ cement concrete ____ of trap
metal using 20 mm and down size coarse graded machine
crushed hard stone aggregate for R.C.C. Beams and Lintels as
per detailed drawings and designs or as directed by Engineer-In
Charge., including centering formwork, compacting, roughening
the surface if special finish is to be provided and curing etc.
complete. with all lead and lifts. (Excluding steel reinforcement.)
(DSR -14- Raigadh Region)
405 Cu. M
26
Providing and casting in situ cement concrete _____ of trap
metal using 20 mm and down size coarse graded machine
crushed hard stone aggregate for R.C.C. Slabs and landings of
all thickness as per detailed drawings and designs,including
centering, formwork, compacting, roughening the surface if
special finish is to be provided and curing etc. complete. with all
lead and lifts. (Excluding steel reinforcement)
Spec. No.:BdF -8 Page No. 302 (DSR -14- Raigadh Region)
337 Cu. M
27
Providing and casting in situ cement concrete _____of trap
metal using 20 mm and down size coarse graded machine
crushed hard stone aggregate for R.C.C. chhajja as per detailed
designs and drawings, including centering, formwork,
compacting, roughening the surface if special finish is to be
provided and curing etc. complete. with all lead and lifts.
(Excluding steel reinforcement)
Spec. No.:Bd-F -9 Page No. 303 (DSR -14- Raigadh Region)
1 Cu. M
28
Providing and casting in situ cement concrete ___ of
trap metal using 20 mm and down size coarse graded machine
crushed hard stone aggregate for R.C.C. canopy as per detailed
designs and drawings, including centering, formwork,
compacting roughening the surface if special finish is to be
provided and curing etc. complete. (Excluding steel
reinforcement). Spec.
No.:Bd-F -10 Page No. 304 (DSR -14- Raigadh Region)
1 Cu. M
29
Providing and casting in situ cement concrete ____of trap
metal using 20 mm and down size coarse graded machine
crushed hard stone aggregate for R.C.C. waist slabs, steps and
parapet as per detailed drawings for staircases, including
centering, formwork, compacting, roughening the surface if
special finish is to beprovided and curing etc. complete.
(Excluding steel reinforcement) Spec.
No.:Bd-F -13 Page No. 305 (DSR -14- Raigadh Region)
27 Cu. M
30
Providing and casting in situ cement concrete ____ of trap
metal using 20 mm and down size coarse graded machine
crushed hard stone aggregate for R.C.C. pardi 100 to 200 mm
thick, including centering formwork, compacting, roughening the
surface if special finish is to be provided and curing etc.
complete. with all lead and lifts. (Excluding steel reinforcement)
Spec. No.:Bd-F -11 Page No. 304 (DSR -14- Raigadh Region)
18 Cu. M
31
Providing and casting in situ cement concrete ____ of trap
metal using 20 mm and down size coarse graded machine
crushed hard stone aggregate for R.C.C. pardi 200 to 500 mm
thick, including centering formwork, compacting, roughening the
surface if special finish is to be provided and curing etc.
complete. (Excluding steel reinforcement) Spec. No.:Bd-F -11
Page No. 304
38 Cu. M
32
Providing and fixing in position steel bar reinforcement of
various diameters for R.C.C. pile caps, footings, foundations,
slabs, beams, columns, canopies, staircases, newels, chajjas,
lintels, pardies, coping, fins, arches, etc. as per detailed
designs,drawings and schedules, including cutting, bending,
hooking the bars, binding with wires or tack welding and
supporting as required etc. complete. Spec. No.:Bd-F -17 Page
No. 306 (DSR -14- Raigadh Region)
172 MT
33
Providing and placing PVC cover block of required size at the
rate of 27 Nos. per 10 Square Metre to reinforcement to give a
clear cover as per I.S.456- 2000 in R.C.C. slabs. (Unit of this item
is for volume of concrete )
SPEC- As directed by Engineer-In-Charge. (DSR -14- Raigadh
Region)
337 Cu. M.
34
Providing and placing in position PVC cover blocks of required
size at 90cm centre to centre to each main bottom bars and to
stirrups at sides to give required clear cover from all sides as per
I.S.456- 2000 in R.C.C. beams etc. complete. (Unit of this item is
for volume of concrete)
SPEC- As directed by Engineer-In-Charge. (DSR -14- Raigadh
Region)
405 CUM
35
Providing and placing PVC cover blocks of required size at 1.50
metres centre to centre near the edge of each side and at cente
when the width is more than 75 cm to reinforcement to give a
clean cover of 40 mm to 65 mm from all sides as per I.S.456-
2000 in R.C.C. columns etc. complete. (Unit of this item is for
volume of concrete
Spec. As directed by Engineer-In-Charge (DSR -14- Raigadh
Region)
139 CUM
36
Providing Second class Burnt Brick masonry with conventional /
I.S. type bricks in cement mortar 1:6 in foundations and plinth
of inner walls & external walls, including bailing out water
manually, striking joints on unexposed faces, racking out joints
on exposed faces and watering etc. complete.
Spec. No.:Bd-G -1 Page No. 313 (DSR -14- Raigadh Region)
185 CUM
37
Providing Second Class Burnt Brick masonry with
conventional/I.S. type bricks in cement mortar 1:6 in
superstructure, including striking joints, racking out joints,
watering and scaffolding etc. complete. Spec. No.:Bd-G -
5 Page No. 315 (DSR -14- Raigadh Region)
524 CUM
38
Providing Second Class Burnt Brick masonry with conventional /
I.S. type bricks in cement mortar 1:4 in half brick thick wall
including mild steel longitudinal reinforcement of 2 bars of 6mm
diameter / 2 hoop iron strips 25mm x 1.6 mm painted with
anticorrosive paint at every third course properly bent and
bonded at ends, scaffolding, racking out joints and watering etc.
complete.
Spec. No.:BdG -7 Page No. 316 (DSR -14- Raigadh Region)
30 SQM
39
Providing Second class Burnt Brick masonry in cement mortar
1:6 using flyash bricks in foundations and plinth of inner walls &
external walls, including bailing out water manually, striking
joints on unexposed faces, racking out joints on exposed faces
and watering complete.
Spec. Bd-.G1 page 313 (DSR -14- Raigadh Region)
1 CUM
40
Providing Second class Burnt Brick masonry in cement mortar
1:6 using flyash bricks in superstructure including striking joints
racking out joints watering and scaffolding complete.
Spec. Bd-G5 page 315 (DSR -14- Raigadh Region)
1 CUM
41
Providing Second class Burnt Brick masonry in cement mortar
1:4 using flyash bricks in half brick thick wall including mild steel
longitudinal reinforcement of 2 bars of 6mm diameter /2 hoop
iron strips 25mm x 1.6mm at every third course, properly bent
and bounded at ends scaffolding racking out joints and watering
complete.
Bd.G7 -8 page 316 (DSR -14- Raigadh Region)
1 SQM
42
Providing uncoarsed rubble masonry of trap stones in cement
mortar 1:6 in foundation and plinth of inner wall, including
bailing out water manually, striking joints on unexposed faces
and watering etc. complete.
Spec. No.:Bd-H. -1 Page No. 329 (DSR -14- Raigadh Region)
47 CUM
43
Providing uncoarsed rubble masonry of trap stones in cement
mortar 1:6 in superstructure, including racking out joints when
plastering is to be done / striking out joints, watering and
scaffolding etc. complete.
Spec. No.:Bd-H. -4 Page No. 331 (DSR -14- Raigadh Region)
1 CUM
44
Providing and laying water proofing treatment of 112 mm
average thickness consisting of 12 mm thick layer in cement
mortar 1:3 with water proofing compound at the rate of one
kilograme per bag of cement as base, constructing and laying
brick bat coba in cement mortar 1:5 with waterproofing
compound at the rate of one kilogramme per bag of cement and
having average thickness of 80mm and finishing with 20 mm
cement plaster layer in cement mortar 1:3 with approved water
proofing compound at the rate of one kilogramme per cement
bag, including all lead, lifts and laid to proper slope to drain off
water entirely inlcuding watta at the junction of parapet and
work upto a height of 30 cm or a directed and, including finishing
the top layer of water proofing treatment with false marking of
30 x 30cm or as directed and covering the whole treatment with
seven year's guarantee, on requisite stamp paper etc.complete.
SPEC- As directed by Engineer-In-Charge. (DSR -14- Raigadh
Region)
1,198 Sq. M.
45
Providing waterproof plaster in W.C. and bath 20 mm thick for
dado in cement mortar 1:3 with neat finishing, floating using
approved waterproofing compound of IS Std. at the rate of one
kg per 50 kg
of cement etc. complete. SPEC- As
directed by Engineer-In-Charge (DSR -14- Raigadh Region)
50 Sq. M.
46
Providing waterproofing in W.C. and bath including
brick bat coba in all positions consisting of specialized materials
as per IS Standard and covering 7 years guarantee on requisite
stamp paper including all leads, lifts etc. complete.
SPEC-As directed by Engineer-In-Charge. (DSR -14- Raigadh
Region)
17 CUM
47
Providing expansion joints in R.C.C. framed structure (at terrace
level) with pre-moulded bituminous filler 25mm thick and 3mm
thick aluminium plate as required bituminous poured filler fixing
lead flushing on upper side and C.C.T.W.battens and inner face
finishing etc. complete as directed
Spec. No.:BdK.-1A Page No.359 (DSR -14- Raigadh Region)
3 SQM
48
Providing and fixing chicken mesh of 22 guage with about 35
cm. width at the junction of R.C.C. membes and brick work, of
approved quality including fixing mesh in position by necessary
nailing in concrete or B.B. masonry and tying by binding wire etc.
complete. As directed by Engineer-in-charge (DSR -14-
Raigadh Region)
324 SQM
49
Providing internal cement plaster 6mm thick in a single coat
without neeru finish to concrete surface in all position including
scaffolding and curing etc. complete. Spec. No.:BdL.-1 Page
No.367 (DSR -14- Raigadh Region)
a) in cement mortar 1:3 1,174 SQM
50
Providing internal cement plaster 12mm thick in a single coat,
without neeru finish to concrete or brick surface in all positions
including racking out joints, scaffolding and curing etc. complete.
Spec. No.:BdL.-2 Page No.367 (DSR -14- Raigadh Region)
a) in cement mortar 1:4 3,350 SQM
51
Providing internal cement plaster 20mm thick in a single coat,
in cement mortar 1:3 without neeru finish to stone masonry and
concrete members surface in all positions including scaffolding,
racking out joints, providing groove at joints of stone masonry
and concrete members and curing etc. complete. Spec.
No.:BdL.-3 Page No.368 (DSR -14- Raigadh Region)
36 SQM
52
Providing sand face plaster externally in two coats using
approved screened sand in all positions, including providing base
coat of 15 mm thick in cement mortar 1:4 mixing approved
water proofing compound at the rate of 1 kilogramme / 50 kg of
cement and curing the same for not less than two days and
keeping the surface of base coat rough toreceive the sand faced
treatment 8 mm thick in cement mortar 1:4 and finishing the
surface by taking out grains and curing for 14 days including
preparing the surface, watering and scaffolding etc.
complete. Spec. No.:BdL.-7 Page No.369 (DSR -14- Raigadh
Region)
1,536 SQM
53
Providing neeru finish to plaster surface in all position including
scaffolding and curing etc. complete. Spec. No.:BdL.-10
Page No.370 (DSR -14- Raigadh Region)
3,350 SQM
54
Providing neeru finish to plaster surface for ceiling
including scaffolding and curing etc. complete. Spec.
No.:BdL.-10 Page No.370 (DSR -14- Raigadh Region)
1,174 SQM
55
Providing 15mm thick water proofing cement plaster in double
coat on RCC Wall of Under Ground Water Tank at any height or
any level finished even and mixed with water proofing
compound ( of Contech Chemicals/CICO or equivalent) and
finished the surface with neat cement slurry at 2.75 Kg/ Sqm
etc., complete including furnishing a bond for 10 years. The rate
shall be inclusive of stopping leakage by using any method such
as grouting etc..hacking the RCC wall and complete. Spec. NO. -
NON DSR
96 SQM
56
Providing and fixing ceramic tiles of IS Std. and approved quality
______ cm size for flooring in required position laid on bed of
cement mortar 1:4 including cement float, filling joint with
white/colour cement slurry, cleaning, curing, etc. complete.
Spec. No.:BdM.-12 Page No.385 (DSR -14- Raigadh Region)
a) 45x45cm. 70 SQM
57
Providing and laying Rectified and vitrified mirror finish
decorative type tiles of size of approved make, shade and
pattern for flooring in required position laid on a bed of 1:4
cement mortar including neat cement float, filling joints with
cement slurry, curing and cleaning
etc. complete. Spec. No.:BdM.-12 Page No.385 (DSR -14-
Raigadh Region)
a) 600 mm x 600 mm and 10 mm thick having
Sqm. water absorption less than 0.05% 577 SQM
58
Providing and laying Rectified and vitrified mirror finish
decorative type tiles of size of approved make, shade and
pattern for dado in required position laid on plaster of 1:4
cement mortar, cement paste, filling joints with neat cement
slurry, curing and cleaning etc. complete. Spec. No.:BdM.-13
Page No.386 (DSR -14- Raigadh Region)
a) 600 mm x 600 mm and 10 mm thick having
water absorption less than 0.05% 147 SQM
59
Providing and fixing machine cut machine polished 18 mm to
20 mm thick telephone black / Amba White / Cat bary brown /
RBI red / Ocean Brown granite stone for treads and risers of
steps and staircases of approved colour and shade with rounded
moulding and three grooved line for the treads on bed of 1;4
Cement mortar including float filling joints with neat cement
slurry curing polishing and cleaning etc. complete.** Spec. No.:
Bd. M.22 B/Page No. 390 ( DSR- 14-15 Pune region)
129 SQM
60
Providing and fixing machine cut mirror polished 18 mm to 20
mm thick telephone black granite / Amba White / Cat bary
brown / RBI red / Ocean Brown granite stone partition with
rounding the edges etc. complete** . A) Both side polish Spec.
No.: Bd.M.35 /Page No.393 ( DSR- 14-15 Pune region)
1 SQM
61
Providing and laying in situ cement concrete M30 with tremix
treatment for 150 mm thickness for flooring with groove cutting
of 4mm wide and 20mm deep with necessary refilling with
bitumen etc. complete. Spec. No.: 12 a / 12 BDM (DSR- 14-15
Pune region As directed by Engineer in charge
3,174 SQM
62
Supply & Spreading Impact HardTop dry shake high
performance floor hardener carborandum based at a dosage of
5 kg per Sqm. Giving a scale of minimum 6 as per Moh's scale
test etc. Complete all as per manufacturer's recommendaions
and as directed by the engineer . Spec. NO. -NON DSR
3,175 Sqm
63
Providing and laying in position flooring of telephone black /
Amba White / Cat bary brown / RBI red / Ocean Brown granite
stone of approved shade and size 18 mm to 20 mm thick on bed
1:6 cement mortar including cement floats striking joints,
pointing in C.M. 1:3 curing and cleaning etc. complete.**
Spec. No.: Bd.M. 3 B/Page No. 380 (DSR- 14-15 Pune region)
17 SQM
64
Providing & laying 50 mm thk.M15 IPS flooring over concrete
surface with marking of lines etc.complete. Spec. NO. -NON
DSR
2,352 SQM
65
Providing and applying one coat of seal cement primer of
approved manufacture and shade, including scaffolding if
necessary, cleaning the surface etc. complete.
SPEC- As directed by Engineer-In-Charge. (DSR -14- Raigadh
Region)
3,319 SQM
66
Providing and applying two coats of exterior Acrylic latex paint
of approved colour and shade to the plastered surface as per
manufacturers specification including scaffolding preparing the
surface etc.
complete. (Excluding primer coat). (DSR -14- Raigadh Region)
3,319 SQM
67
Providing and applying white wash of approved quality in two
coats on old/new plastered or masonry surfaces & asbestos
cement sheets, including scaffolding and preparing the surface
by brushing and brooming down etc. complete.
Spec. No.:BdP.-1. Page No.411 (DSR -14- Raigadh Region)
3,350 SQM
68
Providing and applying washable oil bound distemper of
approved colour, shade and quality to old/new surface, in
______ including scaffolding, preparing the surfaces etc.
complete. (excluding primer coat). (DSR -14- Raigadh Region)
a) Three coat 3,350 SQM
69
Providing and applying primer coat of approved quality to
old/new wall surface to receive oil bound distemper treatment,
including scaffolding, preparing the surface as directed etc.
completed. (Prior approval of S.E. shall be obtained) Spec. As
directed by Engineer-In-Charge (DSR -14- Raigadh Region)
3,350 SQM
70
Providing and laying telephone black / Amba White /
Cadburybrown / RBI red / Ocean Brown granite stone of 18 to 20
mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6
including filling joints with polymer base filler nosing the sharp
edges wherever necessary, curing, etc. complete Spec- 29 / 12
BDM (DSR- 14-15 Pune region)
36 SQM
71
Providing and applying coloured powder coating to the
Alluminium section as per details given or direction etc.
complete. (Colour sample to be got approved from Ex. Engineer
before use)
SPEC- As directed by Engineer-In-Charge. (DSR -14- Raigadh
Region)
26 SQM
72
Providing and fixing sintex or equivalent single leaf door
shutter of approved colour made out extruded rigid PVC hollow
section DWUF-306 shutter frame of size 33 x 47 mm having
double wall construction as vertical styles, top and bottom rails
and middle locks rail of size 33 x 94 mm and the panel in fill
SPUF-101 multichamber hollow plastic section of size 20 x 200
mm joined each other by tongue and groove interlocking system
duly inserted in shutter frame and all shutter frames, lock rails,
styles reinforced by seasoned wood inserted inside for fixing of
hinges, aldrops, tower bolts and door stoppers etc. All corners
should be machine cut, joined each other by metal screw after
inserting rigid "L" bracket PVC reinforcement of size 125 x 200
mm including synthetic metal fixtures and fastenings, remaking
damaged surface . (DSR -14- Raigadh Region)
15 SQM
73
steel door Providing & fixing steel door of approved make,
constructed from 1.5 mm thk MS sheet on both sides fitted on
70x50 mm MS hollow tube, duly filled in foam insulation door
frame of pressed ms sheet 2mm thk, 10mm square bar bracing
at bottom. Vision Glass panel should be 6mm thick toughened
clear glass provided in square in standard dimensions of 300mm
x 300mm. Including all approved type heavy duty fastenings and
fixtures comprisingof :S.S. hinges, Dorma cylindrical lock,
handles 2 Nos., air seal gaskets between shutter and frame,
rubber strip at bottom,"Dorma" make door closers with
synthetic enamal painting etc. complete.(Supplier -Shakti Met-
dor or approved equivalent) Spec. NO. -NON DSR
A) Single Leaf without vision panel 34 SQM
74
Providing and fixing rolling steel shutter fabricated from 18/20
gauges steel laths with side guides, bottom rail, brackets, door
suspension shaft, including rolling springs, locking arrangement
and mechanical gear operation arrangement and one coat of red
lead primer etc. complete. Spec. No.:BdT.-56. Page No.511 (DSR -
14- Raigadh Region)
45 SQM
75
Providing and fixing in position aluminium louvered
windows/ ventilators (IS std.) of various sizes with powder
coating as per detailed drawings and specifications including
aluminium frames 80 x 38 mm box type 5 mm thick sheet glass
louvers, clips / rubber plain P.V.C.. gaskets of approved quality
etc. complete.. (Sample to be got approved from Ex. Engineer
before use) (DSR -14- Raigadh Region)
3 SQM
76
Providing and fixing in position anodized extruded aluminium
openable window of outer frame size 53 x
57mm (or as required size with proportionate change in
weight) of average weight @ 1.118kg/Rmt and shutter of 53 x
57mm (or as required size) of average weight of 0.30 kg/Rmt. (or
as required) with plain sheet glass 5.5mm thick with
neoprene/rubber gasket with hinges, locking arrangement and
wooden encasement wherever necessary etc. complete as
directed by Engineer-incharge SPEC- As directed by Engineer-In-
Charge. (DSR -14- Raigadh Region)
23 SQM
77
Providing and fixing 12 mm thick frameless toughened glass
door shutter of approved brand and manufacture, including
providing and fixing top & bottom pivot & spring type fixing
arrangement and making necessary holes etc. for fixing required
door fittings, all complete as per direction of Engineer-in-charge
(Door handle, lock and stopper etc.to be paid separately). 21.18
(DSR- 14-15 CPWD)
5 SQM
78
Providing and fixing M.S. grill door 24 kg/sqm of various size as
per detailed drawings without hot dip coating, iron fixtures and
fastenings and 3 coats of oil painting etc. Spec. No.: As directed
by Engineer in charge. Spec-27 / 18 BDT (DSR- 14-15 Pune
region)
26 SQM
79
Providing and erecting chain link fencing 1.6 M. height with G.I.
chain link of size 50 x 50 mm 8 guage thick and fixed 75 mm
above Ground level vertical M.S Angle of 40 x 40 x 6 mm size
embedded in C.C. block of 1:4:8 mix of size 450 x 450 x 670 mm.
at 1.75 M.c/c with iron bar 16 mm dia as hold fast including
welding link with angle frame at 30 cm c/c nuts and bolts and
horizontal M.S. Angles at top and bottom of 25 x 25 x 5 mm size
and vertical M.S. flat 35 x 5 mm and 25 x 5 mm horizontal
including cross support of 40 x 40 x 6 mm Angles both sides at
every corner or bends embedded in concrete blocks of 1:4:8 of
size 450 x 450 x 670 mm including 3 coats of oil painting etc.
complete. Spec. No.: As directed by Engineer in charge. spec-32 /
21 BDW (DSR- 14-15 Pune region)
30 Rmt
80
Supplying, fabricating and fixing in position inserts comprising
edge angle, MS angles, plates, tees, flats holding down bolts,
anchor bolts, anchor plates, pipe sleeves, monkey ladder etc., in
all cement concrete works at all levels and heights above
finished floor level in foundation, trenches, pits, tunnels, lift pits
etc., below finished floor level including cutting, bending to
shape fabricating, drilling, threading, welding lugs etc., with all
tools, tackles and labour as per design or as directed including a
coat of primer of approved quality and painting the exposed
surface with two coats of synthetic enamel paint of approved
quality and colour etc., all complete as per drawings and as
directed. Spec. NO. -NON DSR
500 KG
81
Providing and fixing in position-------------- Ultra Violet
stabilized UPVC plumbing pipes of specified outer diameter
required standard thickness confirming to I.S.. 4985, including
necessary fittings confirming to I.S.. 7834, such as P.V.C.. bends,
vees, reducers, clamps, plugs etc. necessary excavation trench,
refilling, necessary drilling holes in walls / slab, and making the
good the surface etc. complete. (For 10.00 Kg/Sq.cm.. pressure)(
including defect liability period and bond for three years.)
SPEC- As directed by Engineer-In-Charge. (DSR -14- Raigadh
Region)
a) 25mm. Diameter 75 RMT
b) 40mm. Diameter 50 RMT
82
Providing and fixing approved and tested water meter bearing
I.S.I. mark with non return valve including strainer, sockets,
union nut and construction ______ of required and adequate
size with M.S. fabricated frame and mild steel hinged cover with
locking arrangement and lock etc. complete.
Spec. No.:BdV.-6 & 7 Page No.553 (DSR -14- Raigadh Region)
with brick masonary chamber
25mm. diameter water meter 1 NO
83
Providing and fixing ___ steel with chromium plating stop tap
of approved quality and make with clutch/ wheel including
sockets/ union nut and brick masonry chamber with cast iron-
frame and mild steel hinged cover with locking arrangement and
lock etc. complete. Spec. No.:BdV.-10 Page No.555 (DSR -14-
Raigadh Region)
a) 20mm. Diameter 1 NO
84
Providing and making ISI Mark ferrule connection of 32 mm dia.
To water main including ferrule coupling cast iron bell mouth
cover, built in non return valve and fixing including excavation
and reinstatement complete. Spec. No.: Bd.V. 4 page 551 (DSR-
14-15 Pune region
2 NO
85
Providing and fixing C.P. Angular stop clock with wall flange
jaquar make continental (CAT.NO. CON-059) including necessary
sockets/union nut etc. complete.** Spec. No.: As directed by
Engineer in charge 49 / 20 BDV (DSR- 14-15 Pune region)
2 NO
86
Providing and fixing C.P.Two way BIB cock jaquar make
continental (CAT.NO. CON-041) including necessary
sockets/union nut etc. complete. Spec. No.: As directed by
Engineer in charge 50 / 20 BDV (DSR- 14-15 Pune region)
6 NO
87
Providing and fixing C.P. wall mixer with provision for overhead
shower with 115mm long bend pipe & wall flange jaquar or
equivalent make continental (CAT.NO. CON-273 UPR) including
necessary sockets/union nut etc. complete.** Spec. No.: As
directed by Engineer in charge 51 / 20 BDV(DSR- 14-15 Pune
region)
1 NO
88
Providing and fixing C.P. pillar cock long neck with aerator j
jaquar or equivalent make continental (CAT.NO. CON -021)
including necessary sockets/union nut etc. complete.** Spec.
No.: As directed by Engineer in charge 52 / 20 BDV (DSR- 14-15
Pune region)
6 NO
89
Providing and fixing C.P. BIB cock with wall flange j jaquar or
equivalent make continental (CAT.NO. CON-047) including
necessary sockets/ union nut etc. complete.** Spec. No.: As
directed by Engineer in charge. 53 / 20 BDV (DSR- 14-15 Pune
region)
1 NO
90
Providing and fixing C.P. sink cock with raised J shaped swinging
casted spout jaquar or equivalent make continental (CAT.NO.
CON -359) including necessary sockets/ union nut etc.
complete.** Spec. No.: As directed by Engineer in charge. 54 /
20 BDV (DSR- 14-15 Pune region)
1 NO
91
Providing and fixing P.V.C. Rain water pipes of 160mm outer
diameter and having wall thickness of 2.2 to 2.7 mm confirming
to I.S. 13592-1992 including proper rainwater receiving recess
with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes,
inluding fixing the pipe on wall using approved wooden cleats
projecting 25mm to 40mm from face of wall a fixing with clips of
approved quality and number ,filing the joint using rubber gasket
with solvent cement and properly resting the shoe of pipes on
C.C. or masonry blocks, including necessary scaffolding and
maintenance for 3 yrs for any leakages or dislocations of pipes.
All the P.V.C. fittings and additional 2 piece socket clips shall be
got approved from engineer in charge etc. complete. (The
contractor shall give 3 yrs guarantee bond for payment) Spec.
No.: As directed by Engineer in charge. spec. no. 54 / 20 BDV
(DSR- 14-15 Pune region)
103 NO
92
Providing and laying in walls/ceilings/floors 15 mm dia.
medium grade having embossed as ISI Mark galvanised iron
pipes of 1.25 kg/metre necessary fitting remaking good the
demolished portion with filling trenches and with primer of anti-
corrosive oil paint , 2 coats complete. Spec. No.: Bd.V.5 Page No.
551, 59 / 20 BDV 5 (DSR- 14-15 Pune region)
25 RMT
93
Providing and laying in walls/ceilings/floors 25 mm dia.heavy
grade having embossed as ISI Mark galvanised iron pipes of 2.49
kg/metre necessary fitting remaking good the demolished
portion with filling trenches and with primer of anti-corrosive oil
paint , 2 coats complete. Spec. No.: Bd.V.5 Page No. 551, 61 / 20
BDV 5 (DSR- 14-15 Pune region)
25 RMT
94
Providing and fixing Indian type white glazed earthenware 625
mm water closet pan including "P" trap, white earthenware foot
rests, Cast Iron soil and vent pipes upto the outside face of the
wall including 100 mm. diameter cast iron plug bend, cement
concrete bedding, 10 litres fibre/UPVC high level flushing cistern
of approved quality and make with fittings, inlet pipe with stop
tap, brackets for fixing the cistern, 32 mm. diameter UPVC flush
pipe with fittings and clamps, 20 mm diameter galvanised iron
overflow pipe with mosquito proof coupling, galvanised iron
chain and pull, painting to the cistern and exposed pipes and
cutting and making good the walls and floors etc. complete.
(Exclusing waterproof brick bat coba) (Cat No : FLV - 1085 SQ)
(DSR -14- Raigadh Region) Bd. V. -20
2 No
95
Providing and fixing European type wall-hung white water
closet of Paryware/Hindware with push valve concealed type
with cover plate 32mm size of JAQUAR MAKE SERIES FLV-1095
including soil pipe ,vent pipe up to outside face of wall ,100mm
dia. G.I. plug bend inlet pipe all fittings, cutting& making good
walls, floors etc. complete.** Spec. No.: 56 / 20 BDV (DSR- 14-
15 Pune region)As directed by Engineer Incharge. Hindware
Make - Studio EWC Cat No. 20041, Cistern Cat no.-21028
4 No
96
Providing and fixing _____ earthenware full stall type Urinal
without flushing cistern with inlet pipes, uPVC flush pipe, stop
tap 32 mm dia. with fittings,uPVC soil pipe,uPVC trap and soil
pipe connection upto the outside face of the wall, making good
to damaged surface, testing etc. complete. (One full stall urinal)
Spec. No.:BdV.-23 Page No.562 ) (DSR -14- Raigadh Region)
Hindware Make - RIVA Cat No. 96003
a) Coloured glazed 1 No
b) White glazed 4 No
97
Providing and fixing ___ earthenware Wash Hand Basin of ____
size including cold water piller taps, brackets, rubber plugs and
brass chain, stop tap, chromium plate bottle trap and necessary
pipe connections including UPVC waste pipe and trap upto the
outside face of the wall, making good the damaged surface,
testing etc. complete.
Spec. No.:BdV.-30 Page No.565 (DSR -14- Raigadh Region)
a) White glazed with bottle trap
b) 55x40 cm. 6 No
98
Providing and fixing ______ pedestal for Wash Hand Basin of
approved size and quality testing etc. complete. Spec- As
directed by Engineer-In-Charge. (DSR -14- Raigadh Region)
a) White glazed 6 No.
99
Providing and fixing Steel sink of size .........including all
connections of G.I.supply and UPVC waste pipe and trap upto
outside face of wall, cold water chromium plated screw down
bib tap, rolled steel or C.I.brackets, rubber plug and brass chain,
top tap, making good the damaged surface, chromium plated
bottle trap testing etc. complete. Spec. No.:BdV.-31 Page No.566
(DSR -14- Raigadh Region)
a) 60x45x25 cm. 1 No
100
Providing and fixing 10 cm dia. C.I.Nahani Trap (long arm)
including symet grating,bend, connecting piece of C.I.pipe upto
the outside face of the wall, making good the damaged surface,
testing etc. complete. Spec. No.:BdV.-32 Page No.567
,(DSR -14- Raigadh Region)
8 No
101
Providing and fixing 10 cm dia. PVC Nahani Trap
fixed with PVC grating, PVC plug bend and piece of
PVC pipe upto plug bend, scaffolding etc. complete. Spec no.-
(DSR -14- Raigadh Region) Bd. V. -32
1 NO
102
Providing and fixing ___ UPVC, Soil vent / waste SWR pipe
conforming to I.S. - 13592, and I.S. - 4985 to withstand continous
internal hydraulic pressure of 4 kg/cm2 including necessary
fittings, such as bends, tees, single junctions, double junctions
and joining with rubber rings and lubricants, over mild steel
bracket m.s. flat of 40mm.wide and 3mm. thick on walls or
laying in ground including necessary excavation, laying, refilling
the trench testing etc. complete.
SPEC- As directed by Engineer-In-Charge. (DSR -14- Raigadh
Region)
a) 75 mm.diameter waste water pipe 50 RMT
b) 90 mm. diameter waste water & soil pipe 100 RMT
103
Providing & fixing in position UPVC, Ultra Voilet stabilised
______ outer diameter cowl dome confirming I.S. 4985 including
making joints with solvent / cement etc. complete.
Spec- As directed by Engineer-In-Charge. (DSR -14- Raigadh
Region)
a) 110mm. 20 RMT
104
Providing, laying concrete pipes of I.S.NP.2 class of ------------ in
proper line, level and slope including, nesessary collars, testing,
excavation, laying, fixing with collars in cement mortar 1:1 and
refilling the trench etc. complete.
Spec. No.:BdV.-41 Page No.573, (DSR -14- Raigadh Region) , (DSR-
14-15 Pune region)
a) 225 mm. diameter 25 RMT
b) 300 mm. diameter 125 RMT
c) 450 mm diameter 100 RMT
d) 600 mm diameter 145 RMT
105
Providing and constructing Brick Masonry Inspection
chamber _____ and 45 to 90 cm in depth including 1:4:8 cement
concrete foundation, 1:2:4 cement concrete channels, brick
masonry, plastering from inside and outside as required in
cement mortar 1:3 and airtight RCC lid with frame fixed in
cement concrete 1:2:4, curing etc. complete. Spec. No.:BdV.-43
Page No.574, (DSR -14- Raigadh Region)
a) 60x45 cm. 5 No
b) 90x45 cm. 10 No
106
Providing and constructing Brick Masonry Interseptic
Chember 90 cm x 45 cm and 90 cm to 150 cm in depth including
1:4:8 cement concrete foundation, M15 cement concrete
channels, fixing salt glazed stoneware intercepting trap with
rodding pipe set in 1:4:8 cement concrete block, brick masonry
plastering inside and outside, airtight C.I.lid with frame fixed in
cement concrete,curing etc.complete.
Spec. No.:BdV.-44 Page No.575, (DSR -14- Raigadh Region)
3 No
107
Providing and fixing 15 x 10 cm of approved quality salt glazed
stoneware gully trap in cement concrete 1:4:8 outside the
building including symet grating in the sink, connecting glazed
stoneware pipe, brick masonry chamber with R.C.C. lid and
Symet grating for the gully trap, testing etc. complete.
Spec. No.:BdV.-38 Page No.572,(DSR -14- Raigadh Region)
4 No
108
Providing and fixing 450 x 550 mm size superior type
Belgium mirror with 16mm dia. nickel plated towel rod etc.
complete. As
directed by Engineer-In-Charge,(DSR -14- Raigadh Region)
4 No
109
Providing hoisting and fixing in position sintex or equivalent
high density polyethylene UV stabilized conforming to I.S.12701,
water storage tank with necessary connections, testing & all
required accessaries etc. complete. (Prior approval of sample
by Ex. Engineer is necessary before use.) As
directed by Engineer-In-Charge.
2 No
110
Providing and fixing--------- Hume pipe septic Tank with pipe
and cap including necessary excavation and laying etc.complete.
Spec. No.:BdV.-45 Page No.575,(DSR -14- Raigadh Region)
a) 1200 mm. Diameter 1 No
111
Providing and fixing reinforced cement concrete cover of size
90 cm x 45 cm with frame over inspection chamber etc.
complete. Heavy duty (225 kg) Spec. No.: As directed by
Engineer in charge.
10 No
112
Providing and fixing reinforced cement concrete cover of size
60 cm x 45 cm with frame over inspection chamber etc.
complete. Heavy duty (160 kg) Spec. No.: As directed by
Engineer in charge. Spec. No. 46a / 20 BDV (DSR- 14-15 Pune
region)
5 No
113
Constructing soak pit 1.20x1.20x1.20 m filled with brickbats
including S.W. drain pipe 100 mm diameter and 1.20 m long
complete as per standard design. Spec. N0/19.33
(DSR-14 CPWD)
1 NO
114
Providing and fixing chromium plated Towel Rails 75cms. long,
16mm dia. and of approved quality fixed on chromium plated
bracket including providing teak wood gutties in masonry etc.
complete. Spec No. (DSR -14-
Raigadh Region) Bd. V. -51
6 NO
115
Providing and fixing PTMT liquid soap container 109 mm wide,
125 mmhigh and 112 mm distance from wall of standard shape
with bracket of the same materials with snap fittings of
approved quality and colour, weighing not less than 105 gms.
Spec. No.-17.71 (DSR-14 CPWD)
6 NO
116Providing and fixing toilet paper holder :
SPEC. NO.-17.34 (DSR-14 CPWD
C.P. Brass 7 NO
117
Making through holes in plain or reinforced cement concrete
with Diamond core drilling system by using Bosch power tools.of
following diameters. Rate in Dia/mm . Spec. NO. -NON DSR
a 52 mm 100 Dia/mm
b 82mm 200 Dia/mm
c 112mm 300 Dia/mm
d 122mm 450 Dia/mm
e 152mm 450 Dia/mm
f 202mm 500 Dia/mm
118
Providing Pre-constructional Anti termite treatment by treating
the bottom surface and the sides of excavation in soil with the
plinth beams at the rate of 3 litres of emulsion concentrate of
one percent concentration of chlorpyrifos 20% F.C. (i.e. by
diluting 5 ltr. of chlorpyrifos 20% EC with 95 ltr. of water) ISI
approved conforming as per I.S. 8944 & I.S. 6313 (Part II 1981)
and spraying by high volume sprayer per square metre surface
area with ten years guarantee bond etc.complete. SPEC- As
directed by Engineer-In-Charge. (DSR -14- Raigadh Region)
3,167 SQM
119
Providing and fixing mild steel grill gate with angle iron frame 65
x 65 x 10 mm with iron bars at 150 mm etc. centre to centre and
diagonal flats as per the detailed drawing, including hinges, pivot
blocks, locking arrangement, welding, reveting with oil painting
in three coats of approved colour shade etc. complete. (Weight
of gate 35 kg /sq.m.)
Spec. No.:BdW.-6 Page No.585, (DSR -14- Raigadh Region)
8 SQM
120
Fixing of PEB Supplied Templates and Bolts by using Total
Station, making arrangements for proper stability of Bolts during
concrete casting by tacking the bolts with reinforcements and
removing the templates and nuts after concreting. The rate shall
also include the cleaning and providing grease and making the
upper portion of bolts completely clean and covering the same
after concreting. Necessary precaution shall be taken to make all
the bolts straight and all in one level comlete as per the drawing
and instruction from Engineer-in-charge. Size of the Bolt may
vary from 700mm to 1200mm. Spec. NO. -NON DSR
440 NO
121
Providing and casting in situ "Conbextra" GP-2 non-shrink
grout as per manufactures specifications including all
materials,tools , shuttering ,pouring at specified consistency,
cleaning etc. complete. Spec. NO. -NON DSR
1 CUM
122
Providing, fabricating and fixing Automatic Gate of 9.00 Mtrx
1.80 Mtr with Rectangular Tubular Sections of 100x50x4mm as
the outer frame and with 50x50x3mm as the internal sections
for distributions. The inner side shall have 2mm perforated
MS/GI sheet welded onto the outer frame. The Total length of
the gate will be 14.00 Mtr sliding on other side of the compound
wall, which should be automated. Gate shall be either from
Progate, Avians or Gandhi. The strucural quantity can be
calculated as per the Basic Drawings. Spec. NO. -NON DSR
1 NO
123
Same as above but without any Automation and sliding, the gate
will be a swing type of gate with a dimension of 1.5 Mtr x 1.80m
Height. Spec. NO. -NON DSR
1 NO
124
Providing & applying ( BASF UCRETE MF) of a 4 component,
single layer, seamless, solventfree, moisture insensitive and food-
safe polyurethane concrete flooring system of density more than
1950 kg/cu.mtr to have a smooth & even
matt finish matching below mentioned performance properties:
198 Sqm
1. mixed density more than 1900kg/cu.mtr,
2. abrasion resistance class of AR0.5 as per BS 8204-2
3. Cleanable to standards of Stainless steel
4. Zero Absorption as per CP.BM2/67/2
5. Static Modulus of Elasticity of 3.3x10^3 Mpa and Toughness
of 96.7x10^3 Mpa as per Modified ASTM C469/C469M
6. Coefficient of thermal expansion of 3.6 x 10^-5 /oC as per
ASTM C531
7. Shore D hardness of 80
8.Tensile strength of >7Mpa
9. Flexural strength of >20Mpa
10. Adhesion to concrete of more than 2Mpa or until concrete
fails
11. slip resistance classification 35 as per EN13036-4
12. Fire resistance classification of Bfl-S1 as per EN 13501-
1:2002
13. Surface spread of flame of CLASS 2 as per BS476, Part 7
14.Cure time of 12 hours for foot traffic and 24 hours for
vehicular traffic at 30 degree C
Applied at a thickness of 3mm over a 1mm scratch coat of the
samematerial by an authorised applicator of the manufacturer
in accordance to the application guideline as provided by the
manufacturer.
125
Providing and spreading 20 / 40 / 60 mm metal in 75 mm
thk.layer including spreading etc copmlete. In the kiosk and
Transformer area. Spec. NO. -NON DSR 50 Sqm
126
Providing and finishing the chasing done for electrical conduting
after finishing the walls with POP upto a width of 200mm etc.
complete. Rate is applicable for at all levels & height. Spec. NO. -
NON DSR 100 Rmt
127
Providing and fixing anchor fastener for concrete including
drilling holes filling holes with Nitomorter PE and cleaningall as
per manufacturers specification. With necessary holes, filling
scaffoldings etc. complete.( Hilti make ) Spec. NO. -NON DSR
A) 8mm dia (upto 150mm long) 50 no
B) 10mm dia (upto 150mm long) 50 no
C) 12mm dia (upto 200mm long) 50 no
D) 16mm dia (upto 200mm long) 50 no
128
Providing and fixing of MS Rungs , made with 25X5 flat with PVC
cover to protect from corrosion, fixing in correct level and line
with required spacing for using it at maintenance time in all
tanks wherever necessary. Spec. NO. -NON DSR
50 nos
129
Providing and laying PE sheet of 250 microns thickness below
concrete floor including cutting the sheet in required size, laying
the sheet, providing a minimum of 200 mm wide laps at the
joints etc. complete. Spec. NO. -NON DSR
3,170 Sqm
130
Excavation for roadways in soft strata such as
______ including dressing section to the required grade, camber
and side slopes and conveying the
excavated materials with all lifts upto a lead of 50 m
and spreading for embankment or stacking,
disposing as directed etc. complete. Spec. No.:Rd. 2,3,4. Page
No. 180,183,184, (DSR -14- Raigadh Region)
a) earth soil of all sorts sand, gravel or soft murum 1,301 Cum
131
Excavation catch / side water gutters _______ to the
specified section including stacking the excavated
stuff in a regular bund if necessary and disposing off
unsuitable or excess stuff as directed upto 50 mtr.
etc. complete. Spec. No.:Rd. 9 Page No. 187, (DSR -14- Raigadh
Region)
a) in Hard murum 284 Cum
132
Painting on kerbs in black and yellow alternate bands
complete as per drawing and technical specifications.
SPEC. NO.-803 (DSR -14- Raigadh Region)
248 SQM
133
Watering and compacting of embankment formed of
materials obtained from the road cutting, within a lead of
50m, to 95% of standard proctor density after laying them
in layers of 20 cm to 30 cm with vibratory roller. Spec. No.:
MORTH 305, 11a / 23 MORTH 305
1,800 CUM
134
Construction of granular sub-base by providing close
graded Material conforming to specifications, mixing in a
mechanical mix plant at OMC, carriage of mixed material
by tippers to work site, for all leads & lifts,
spreading in uniform layers of specified thickness with
motor grader on prepared surface and compacting with
vibratory power roller to achieve the desired density,
complete as per specifications and directions of Engineerin-
Charge. SPEC. NO.-16.78
DSR-14 CPWD
With material conforming to Grade-II (size range 53 mm to
0.075 mm ) having CBR Value-25 651 CUM
135
Providing, laying, spreading and compacting stone
aggregates of specific sizes to water bound macadam
specification including spreading in uniform thickness,
hand packing to proper grade and camber, applying and
brooming requisite type of screening/ binding Materials to
fill up the interstices of coarse aggregate, watering and
compacting with Intelligent Compactor with compaction
analyzer and V-Sat attachment. to the required density. By
Manual Means Grading I a) (Using Screening Crushable
type such as Moorum or Gravel) Spec. No.: 80A i a / 23
MORTH 404 (DSR- 14-15 Pune region
651 CUM
136
Providing and fixing heavy duty inter locking concrete
Coloured paving blocks of 100 mm thickness of having a
strength of 500 kg/Sq.cm. of approved quality and shape
on a bed of crushed sand of 25 to 30 mm thick including
skirting joints and cleaning etc. complete ** Spec. No.: A
directed by Engineer in charge. Spec. no. -21B i/ 12 BDM
(DSR- 14-15 Pune region)
1,541 SQM
137
Providing and fixing heavy duty inter locking concrete
Coloured paving blocks of 80 mm thickness of having a
strength of 400 kg/Sq.cm. of approved quality and shape
on a bed of crushed sand of 25 to 30 mm thick including
skirting joints and cleaning etc. complete ** Spec. No.: As
directed by Engineer in charge
1,062 SQM
138
Providing and casting in situ or precast tapering R.C.C. 1:1
1/2:3 Kerbs type-I as per Drg. No. 13 dt. 20-4-79, 30mm
wide tapering 225 mm to 150 mm embedded 25mm below
ground level finished neatly with C.M. 1:2, setting the
same in C.M. 1:2, painting exposed surface of the kerbs
with 2 coats of road marking paint of approved quality and
colour including the required excavation in any strata and
removing the excavated stuff any where in city and redoing
the surface as specified and directed. Spec. No.: 48 / 23
MORTH 409 (DSR- 14-15 Pune region)
496 RMT
139
Boring/drilling bore well of required dia for casing/ strainer pipe,
by suitable method prescribed in IS: 2800 (part I), including
collecting samples from different strata, preparing and
submitting strata chart/ bore log, including hire & running
charges of all equipments, tools, plants & machineries required
for the job, all complete as per direction of Engineer -in-charge,
upto 90 metre depth below ground level. spec. no- 24.1 , DSR 14-
CPWD
All types of soil -
a) 300 mm dia 500 mtr
Rocky strata including Boulders -
a) 300 mm dia 100 mtr
140
Supplying, assembling, lowering and fixing in vertical position in
bore well, unplasticized PVC medium well casing (CM) pipe of
required dia, conforming to IS: 12818, including required hire
and labour charges, fittings & accessories etc. all complete, for
all depths, as per direction of Engineer -in-charge.
spec. no- 24.3 , DSR 14- CPWD
a) 200 mm nominal size dia 600 mtr
141
Supplying, filling, spreading & leveling stone boulders of size
range 5 cm to 20 cm, in recharge pit, in the required thickness,
for all leads & lifts, all complete as per direction of Engineer-in-
charge. Spec. No.-24.5 , DSR 14- CPWD
6 Cum
142
Supplying, filling, spreading & leveling gravels of size range 5 mm
to 10 mm, in the recharge pit, over the existing layer of boulders,
in required thickness, for all leads & lifts, all complete as per
direction of Engineer-incharge. Spec. No- 24.6 , DSR 14- CPWD
6 Cum
143
Supplying, filling, spreading & leveling coarse sand of size range
1.5 mm to 2 mm in recharge pit, in required thickness over
gravel layer, for all leads & lifts, all complete as per direction of
Engineer -in-charge. Spec. No- 24.7, DSR 14-
CPWD
6 cum
144
Gravel packing in tubewell construction in accordance with IS:
4097, including providing gravel fine/ medium/ coarse, in
required grading & sizes as per actual requirement, all complete
as per direction of Engineerin- charge. Spec. No- 24.8, DSR 14-
CPWD
15 cum
TOTAL AMOUNT