We congratulate you on becoming the fortunate owner of a SAINT HONORÉ watch. Developed and manufactured in our workshops, the sophisticated design and quality of craftmanship displayed by this watch make it an exceptional product which will be your companion for many years to come. This manual contains all the setting instructions. Before doing any technical work, always consult a SAINT HONORÉ approved agent.The list of agents and warranty terms are to be found in the warranty booklet

Operating Instructions

BASIC SETTINGS FOR ALL COLLECTIONS Crown in position 1 : operating position. Crown in position 2: date correction. Only applicable to models with a date function. Avoid changing the date between 23.00 and 1.00 hours as this could damage the mechanism. Crown in position 3 : hour/ minute correction.

For the 326 model, the setting crown is located at 12.00 hours. Be sure to return the crown to position 1 after each operation.

30 minutes timer 1/10e secondes Timer

Pushbutton A

Pushbutton B

1 2 3

Second hand 60 seconds Timer

2

CHRONOGRAPH MODELS - REF 776... / 855... / 892...

Settings for Chronographs : COLOSEO, ESTELLA, EUPHORIA CHRONOGRAPH, MANHATTAN, ORSAY, ROMA,SILVERSTONE, SPEED-BOAT. Basic settings : see page 2. Chronograph functions :Chronograph start : press pushpiece A. Chronograph stop : press pushpiece A again. Chronograph restart : press pushpiece A again. Return to zero : press pushpiece B.Measuring intervening time :Chronograph start : press pushpiece A. Reading time 1 : press pushpiece B. Reading time 2 : press pushpiece B again. The hand will then catch up with the time elapsed. The operation can be repeated several times. Reading last time : press pushpiece A. Return to zero : press pushpiece B.Set the counter to zero :60 seconds counter : crown in position 3, press several times pushbutton A. 1/10th counter : crown in position 3, press several times pushbutton B. 30 minutes counter : crown in position 2, press several times pushbutton B.

Minutes timer

Pushbutton A

Pushbutton B

1 2 3

Center shop-second 1/10e second TimerHour counter after 30m.

3

ORSAY - MONCEAU CHRONOGRAPH - REF 885... / 898...

Basic settings : see page 2. Chronograph functions : Chronograph start : press pushpiece A. Chronograph stop : press pushpiece A again. Chronograph restart : press pushpiece A again. Return to zero : press pushpiece B. Intermediate or interval timing : Chronograph start : press pushpiece A. Reading time 1 : press pushpiece B. Reading time 2 : press pushpiece B again. The hand will then catch up with the time elapsed. The operation can be repeated several times. Reading last time : press pushpiece A. Return to zero : press pushpiece B.Adjusting the Chronograph hands to zero position : - Pull out the crown in position 3. - Keep push-button A & B depressed simultaneously for at least 2 seconds (the centre stop-second rotates by 360°). - Adjusting the centre stop-second with button A. - Adjusting the nest hand B. - Adjusting the minute counter hand with button B. - Adjusting with button A. - Returning the crown to position 1, end of adjusting.

1 2 3

4

AUTOMATIC MODELS - REF 877... / 879... / 880... 881... / 897... Settings for Automatic models : HAUSSMAN, MANHATTAN, MONCEAU, ORSAY, SPEED-BOAT. The automatic mechanical movement is activated by the movement of your wrist. Manual winding is only necessary if you do not wear the watchfor several days.Basic settings : Crown in position 1: operating and winding position. Take care not to overwind the mechanism (4 to 5 turns maximum). Crown in position 2 : correct the date (Except for model 881... (no date)). Avoid changing the date between 23.00 and 1.00 hours as this could damage the mechanism. Crown in position 3 : hour/minute correction.

Be sure to return the crown to position 1 after each operation.

1 2 3

a

b

2nd time zone

5

AUTOMATIC MODELS DUAL TIME - REF 879... Settings for Automatic models Dual time : COLOSEO. The automatic mechanical movement is activated by the movement of your wrist.Manual winding is only necessary if you do not wear the watch for several days. Basic settings : Crown in position 1 : operating and winding position. Take care not to overwind the mechanism (4 to 5 turns maximum). Crown in position 2 : correct the date. Avoid changing the date between 23.00 and 1.00 hours as this could damage the mechanism. Crown in position 3 : hour/minute correction. Verification of the jump of the date (=midnight) (3) : - Turn in direction (a) until the date jumps (=midnight).Adjustment of second time zone and the central hour (3) : - Turn in direction (a) until wanted second time zone reached. - Turn in direction (b) until wanted central hour reached (Only the minu te hand of the second time zone turn). Date correction : - Turn in (a) direction to set the date.

Be sure to return the crown to position 1 after each operation.

30 minutes timer

Pushbutton A

Pushbutton B

12 Hours Timer 60 seconds Timer

1 2 3

6

AUTOMATIC MODELS DUAL TIME - REF 874... Settings for Automatic Chronograph modelsCOLOSEO VALJOUX 7750. The automatic mechanical movement is activated by the movement of your wrist. Manual winding is only necessary if you do not wear the watchfor several days. Basic settings :Crown in position 1 : operating and winding position.Take care not to overwind the mechanism (4 to 5 turns maximum). Crown in position 2 : correct the date. Avoid changing the date between 23.00 and 1.00 hours as this coulddamage the mechanism. Crown in position 3 : hour/minute correction. Verification of the jump of the date (=midnight) (3) : - Turn in direction (a) until the date jumps (=midnight).Date correction : - Turn in (a) direction to set the date.Chronograph functions : Chronograph start : press pushpiece A. Chronograph stop : press pushpiece B.

Be sure to return the crown to position 1 after each operation.

7

SAINT HONORE PARIS SASZA - BP 31

25140 CHARQUEMONTFRANCE

Tel. : +33 (0)3 81 68 66 88Fax. : +33 (0)3 81 44 02 54

Email : sh@saint-honore-paris.com

www.saint-honore-paris.com