©SA

FETY

SO

LUTI

ON

S JO

NSE

RED

S

1/14

I-GUIDE

IG-SAFEPASS ROAD BARRIER ACCESSORIES-1742

SAFEPASS™ ROAD BARRIER ACCESSORIES

©SA

FETY

SO

LUTI

ON

S JO

NSE

RED

S

2/14

SAFEPASS™ GENERAL

About SafePass™ Road Barrier AccessoriesThis manual and its products are intended to be used with the IG-SafePass Road Barrier and the products that it contains. The accessory products in this I-Guide are not tested according to EN 1317.

General requirements! Always do an assessment and a method statement for the installation.! Perform a safety inspection on products before use.! Never use damaged or rusty materials.! Use tools intended for the installation. ! Use lifting equipment with sufficient load capacity.! Use adequate personal protection equipment.! Use personal fall arrest equipment when working at height.! Installation and handling of the road barrier shall be done by trained, competent personnel.! Safety Solutions Jonsered’s (SSJ) product liability only applies to combinations of SSJ products that are assembled according to SSJ’s I-guides.! No design changes may be made without consulting SSJ. ! Make sure all documentation needed is available and up-to-date.

Safety recommendationsRoad barrier systems are often installed in dangerous circumstances with live carriage near by. Make sure national safety regulations are followed when working with the road barrier!

SSJ recommend that an adequate safety zone between the working area and the carriage way is maintained during installation/dismounting. Never work alone!

©SA

FETY

SO

LUTI

ON

S JO

NSE

RED

S

3/14

SAFEPASS™ ROAD BARRIER 2,58 m

SafePass Road Barrier 2,58 m9-760-03-070

Galvanized625 kg

12002580

1000

2680450

50

80

70

0

200

SafePass™ Road Barrier 2,58 m shall be stored, handled, mounted and demounted according to IG-SafePass Road Barrier

IG-SafePass Road Barrier

Stacking/Storage/Transport/Handling/Installation

Specification

Radii capacity R54 m

MAX height difference at joint 4.5 cm

©SA

FETY

SO

LUTI

ON

S JO

NSE

RED

S

4/14

SAFEPASS™ HINGED BARRIER

SafePass Hinged Barrier9-760-03-090

Galvanized680 kg

Storage/TransportThe SafePass™ Hinged Barrier shall be stored, handled, mounted and demounted according to IG-SafePass Road Barrier

HandlingLift the long part of the Hinged Barrier, using 2 leg chain sling/webbing sling/lifting clamp or forks. Attention! The shorter part of the Hinged Barrier is loose – risk of injuries due to crushing. Also, the center-of-gravity-location can change during lift.

IG-SafePass Road Barrier

1000

450

50

80

70

0200

625

1201

2603736

± 95°

©SA

FETY

SO

LUTI

ON

S JO

NSE

RED

S

5/14

SAFEPASS™ HINGED BARRIER

Installation of the Hinged BarrierConnect the Hinged Barrier to the barrier system with the same method as for regular barrier elements. The angle is easily changed after the hinge has been put down. Lift the end and adjust as necessary.

Guide markings for 6° and 45° are available in the lid of the hinge – align the tip of the triangle to the center line of the barrier system.

AnchoringAnchor the long part of the Hinged Barrier (and the short part, if necessary) after installation. Drill Ø22 mm holes through the holes in the anchoring plate. Thereafter, drive 4 anchor nails into the each anchoring plate.

Ø2

2

4 x

6° 45°

©SA

FETY

SO

LUTI

ON

S JO

NSE

RED

S

6/14

SAFEPASS™ HINGED BARRIER

Installation of GC BarrierThe lid in the hinge has sleeves to allow for installation of GC Barriers. The long part of the Hinged Barrier has the same legnth as one GC Barrier. At the short part side – overlap the GC Barriers in the next Road Barrier. Secure the GC Barriers using GC Barrier Clamps.

Split the Hinged BarrierThe parts of the Hinged Barrier can be used seperately, e.g. as end elements. Loosen the bolts in the upper lid (M12 bolts), and lift the element apart.

©SA

FETY

SO

LUTI

ON

S JO

NSE

RED

S

7/14

SAFEPASS™ MULTI FIXING

SafePass Road Barrier Multi Fixing9-760-03-080

Galvanized3,3 kg

260

62 64

62

13

5

15

5 36

,5

98

12

5

WAF 18

Mounting Multi FixingPlace the Multi Fixing in the service channel. Lock the Multi Fixing by tightening the screw.Make sure that the Fixing Wing grips properly to the service channel slot.

©SA

FETY

SO

LUTI

ON

S JO

NSE

RED

S

8/14

SAFEPASS™ MULTI FIXING

Mounting road signPlace the road sign in the square hole, make sure that the post reach down all the way to the service channel bottom. Lock the post by tightening the screw.

Mounting GC BarrierPlace one of the GC Barrier posts in the Road Barrier Connector.Place the other post in the oval hole of the Multi Fixing.

©SA

FETY

SO

LUTI

ON

S JO

NSE

RED

S

9/14

Ø37 150,5

601

23

SAFEPASS™ GC END ATTACHMENT

SafePass Road Barrier GC End Attachment9-760-03-121

Galvanized1,8 kg

Install the GC End AttachmentTwist the GC End Attachment to fit beneath the locking pin at the Road Barrier end. Adjust the GC End Attachment to make sure that tha flat bar is supported by the locking pin.

Install the GC BarrierFit the GC Barrier post to the GC End Attachemnt sleeve.

©SA

FETY

SO

LUTI

ON

S JO

NSE

RED

S

10/14

SAFEPASS™ X3 FIXING

SafePass Road Barrier X3 Fixing9-760-03-077

Galvanized1,2 kg

135

115

98

60

15

5

WAF 18

Mounting delineator panel in X3 FixingDismount the two screws and place the delineator panel between the plates. Drill new holes in the panels if necessary.

NOTE! Drill the holes in the right position – The X3 Fixing shall lay on top of the barrier when mounted.

©SA

FETY

SO

LUTI

ON

S JO

NSE

RED

S

11/14

SAFEPASS™ X3 FIXING

Mounting X3 Fixing in the BarrierPlace the X3 Fixing in the service channel. Lock the Multi Fixing by tightening the screw.Make sure that the fixing wing grips properly to the service channel slot.

©SA

FETY

SO

LUTI

ON

S JO

NSE

RED

S

12/14

SAFEPASS™ SOFTEND

SafePass SoftEnd9-760-03-125

PVC sheet3,0 kg

SoftEnd – end protectionSoftEnd offers protection for vulnerable road users such as pedestrians and bicyclist. Attach the SoftEnd to the Road Barrier end, using the included straps.

©SA

FETY

SO

LUTI

ON

S JO

NSE

RED

S

13/14

SAFEPASS™ INSPECTIONS & MAINTANENCE

Final inspectionWhen installation is completed, a final safety inspection shall be carried out. The inspection shall be performed using the control guide C-Guide SafePass Road Barrier.

Regular inspectionsRegular inspections shall be carried out, preferably on a daily basis. The C-Guide SafePass Road Barrier can be used as a basis for the inspection.

Inspection after impactIf an impact has occurred, the barrier system must be inspected. Inspection and any repairing/disposal shall be carried out by competent personnel, using the general maintenance guide M-Guide SafePass Road Barrier General in combination with the product specific M-Guides.

RecyclingProducts or part of products shall be recycled to the extent possible.

©SA

FETY

SO

LUTI

ON

S JO

NSE

RED

S

14/14

Tecnichal support

For further information, please contact us:

Safety Solutions Jonsereds ABLägervägen 3SE-832 96 Frösön, SWEDENTel +46 (0)10 498 15 00jonsereds.com

SAFEPASS™ CONTACT