Upload
others
View
8
Download
0
Embed Size (px)
Citation preview
BIOSBIOS BatteryBattery
intel i350intel i350
REMOVE
REMOVE
CPU 1
REMOVE
REMOVE
CPU 0
intel wellsburg
PCH
Intel wellsburg
PCH
1 2 3
Top View
Without jumper
Jumper
Pins 1 2 3
Top View
With jumper installed on pins 1 and 2
1 2
SATA Cable x 2 Rear I/O Shielding x 1Quick
Installation Guide x 1
1 2 3 Unlock the clips. Insert the memory module. Lock the clips.
Note: Please save and replace the CPU protection cap when returning the server board for service.
Server Board x 1
DOA/RMA Reminder
Phillips Screwdriver Anti-Static Wrist StrapFlat-head Screwdriver
Insert the server board into the chassis.Attach the server board to the chassis by securing the screws on the designated locations.
S7086 Quick Installation Guide Document # D2305-100 / Revision 1.0
To avoid damage, Note: do not use torque force greater than 7kgf/cm (6.09 lb/n) on each screw.
Read Me First
Package contents
Tools Prepared
Motherboard Placement
1. The motherboard User’s Manual is available for download from our Web site at http://www.tyan.com. Make sure to read all precautions and instructions before you start installing the server board.
2. Refer all servicing to qualified personnel to avoid the risk of damage to the server board.
3. Exercise normal ESD (Electrostatic Discharge) procedures during system integration. TYAN/MiTAC recommends wearing gloves and an anti-static wrist strap to avoid possible damage to the equipment.
4. Current processor socket design places the pins on the motherboard instead of the processor itself. Exercise extreme aution when installing the processors as the manufacturer’s warranty does not cover damage inflicted upon the mother-board, including damage to the CPU sockets.
Quick Installation Guide
Jumper Cap On/Off
www.tyan.com
1 Install the Server Board
2 Install the Processor
3 Install the CPU Heatsink
4 Install the Memory
5 Install the Power Cable
Locate the External I/O Port
Driver's and Utilities CD x 1
Open the socket lever.1 Open the
other socket lever.2
Remove the other CPU protection cap attached on the socket cover.
5
3 Open the socket cover to the fully position.
6 Close the CPU Socket Cover.
4 Install the processorand make sure thegold arrow is located inthe right direction.
7 Close the socket levers. 8 Close the
other side lever.
1 Remove the protective sheet. 2 Install the CPU heatsink.
CONNECTORS
MEMORY SLOTS
CPU0 DIMM G/H/I/J
CPU1 DIMM K/L/M/N
PCIE SLOTS JUMPER/HEADER
a PSU Alert Disable Jumper(3PHD_9)b BIOS Security Override Jumper(3PHD_4)c ME Recovery Mode Jumper(3PHD_6)d Buzzer Disable Jumper(4PHD_1)e Intel MIC Card Jumper(3PHD_3) f ID_LED Button Header(2PHD_2)g Chassis Intrusion Header(2PHD_1)
12
3
67
8
910
11
13
14
20
2122
19
18
2425 232726282932
171615
1. LAN Port#3 (shared with IPMI) & USB 3.0 Ports 2. SATA 3.0 Connector(SATA5,up SATA4,down)3. COM Port & VGA Port 4. 4-pin Fan Connector( SYS_FAN4)5. ID_LED Button6. Clear CMOS Button 7. LAN Port#1(LAN1)8. LAN Port#2(LAN2)9. ID_LED10. 4-pin Fan Connector (SYS_FAN5)11. TYAN Module Header(DBG_HD1)12. BMC_LED13. COM Port (COM2)14. Fan IO Header (Fan_HD1)15. Front Panel Header (FP_HD1)/ LAN2 LED Header (LAN LED_HD1) 16. IPMB Connector (IPMB_HD1)
17. 4-pin FAN Connector(CPU0_FAN)18. 8-pin Power Connector(PW2)19. 4-pin FAN Connector(SYS_FAN3)20. 4-pin FAN Connector(SYS_FAN2)21. 4-pin FAN Connector(SYS_FAN1)22. 8-pin Power Connector(PW3)23. PCIE Header (PCIEx4 From CPU1 SAS HD1,right/SAS HD2,left)24. 4-pin Fan Connector(CPU1_FAN)25. USB 2.0 Connector(USB2_HD1)26. PSMI Connector (PSMI_HD1)27. 24-pin Power Connector(PW1)28. USB 3.0 Connector (USB3_HD1)29. TYPE_A USB Header(TYPEA_USB3) 30. 4-in-1 Mini SAS Connector(SSATA0-3)31. PCH SATA SGPIO Header(SGPIO1,SATA0-5)32. 4-in-1 Mini SAS Connector(SATA0-3)
A PCI-E Gen3 x8 MEZZ Slot f/ CPU0 for LAN cardB PCI-E Gen3 x16 slot(x16 link) f/ CPU1C PCI-E Gen3 x16 slot(x16 link) f/ CPU0D PCI-E Gen3 x4 slot(x8 link) f/ CPU1E PCI-E Gen3 x4 slot(x8 link) f/ CPU0F PCI-E Gen3 x8 MEZZ Slot f/ CPU0 for SAS card
COM1 USB3.0X2
(LAN1-LAN2)
ID LED Button
Shared With IPMI(LAN3)
AB
E
F
M
JIC
D
54
abc
gf
31
VGA
AST2400
d
GH
KL
NCPU1_DIMM_A0CPU1_DIMM_A0
CPU1_DIMM_B0CPU1_DIMM_B0CPU1_DIMM_B1CPU1_DIMM_B1
CPU1_DIMM_D1CPU1_DIMM_D1
CPU1_DIMM_C1CPU1_DIMM_C1
CPU0_DIMM_A1CPU0_DIMM_A1
CPU0_DIMM_B1CPU0_DIMM_B1
CPU1_DIMM_D0CPU1_DIMM_D0
CPU1_DIMM_C0CPU1_DIMM_C0CPU0_DIMM_A0CPU0_DIMM_A0
CPU0_DIMM_B0CPU0_DIMM_B0
CPU0_DIMM_D1CPU0_DIMM_D1
CPU0_DIMM_C1CPU0_DIMM_C1CPU0_DIMM_D0CPU0_DIMM_D0
CPU0_DIMM_C0CPU0_DIMM_C0
3 Secure the heatsink screws.
e
30
CPU1_DIMM_A1CPU1_DIMM_A1
12