S5800 Series Ethernet CLI | FS · 2017. 10. 26. · 11Layer2ProtocolsTunnelingCommands.....167 11.1l2protocolenable.....167

FiberstoreOS

Ethernet Command Line Reference

Contents

1 Interface Commands................................................................................................................................... 71.1 bandwidth.......................................................................................................................................................... 71.2 clear counters.....................................................................................................................................................81.3 description......................................................................................................................................................... 91.4 duplex.............................................................................................................................................................. 101.5 speed................................................................................................................................................................ 111.6 flowcontrol...................................................................................................................................................... 121.7 interface...........................................................................................................................................................131.8 interface range................................................................................................................................................. 141.9 interface range create vlan...............................................................................................................................151.10 jumboframe................................................................................................................................................... 161.11 system jumboframe size................................................................................................................................ 171.12 media-type.....................................................................................................................................................181.13 shutdown....................................................................................................................................................... 191.14 load-interval.................................................................................................................................................. 201.15 vlan dot1q tag native..................................................................................................................................... 211.16 show interface............................................................................................................................................... 221.17 show interface status..................................................................................................................................... 231.18 show interface summary................................................................................................................................241.19 show ip interface........................................................................................................................................... 251.20 switchport...................................................................................................................................................... 261.21 switchport access allowed............................................................................................................................. 271.22 switchport access vlan...................................................................................................................................281.23 switchport mode access.................................................................................................................................291.24 switchport mode trunk...................................................................................................................................291.25 switchport mode dot1q-tunnel.......................................................................................................................301.26 switchport mode trunk ingress-filter............................................................................................................. 311.27 switchport trunk allowed...............................................................................................................................321.28 switchport trunk native..................................................................................................................................33

2 Interface Errdisable Commands..............................................................................................................352.1 errdisable detect...............................................................................................................................................352.2 errdisable recovery interval.............................................................................................................................362.3 errdisable recovery reason...............................................................................................................................372.4 errdisable flap..................................................................................................................................................382.5 show errdisable detect..................................................................................................................................... 392.6 show errdisable recovery.................................................................................................................................40

2.7 show errdisable flap........................................................................................................................................ 41

3 MAC Address Table Commands............................................................................................................ 423.1 mac-address-table ageing-time........................................................................................................................423.2 mac-address-table forward.............................................................................................................................. 433.3 mac-address-table discard............................................................................................................................... 443.4 clear mac address-table................................................................................................................................... 453.5 show mac address-table ageing-time...............................................................................................................463.6 show mac address-table...................................................................................................................................463.7 show mac address-table count.........................................................................................................................483.8 show mac-filter address-table..........................................................................................................................483.9 show resource mac-filter................................................................................................................................. 493.10 show resource static-fdb................................................................................................................................50

4 VLAN Commands......................................................................................................................................524.1 vlan database................................................................................................................................................... 524.2 vlan replace dscp............................................................................................................................................. 534.3 vlan.................................................................................................................................................................. 544.4 vlan VLAN_LIST............................................................................................................................................554.5 show vlan.........................................................................................................................................................564.6 show vlan all....................................................................................................................................................564.7 show vlan brief................................................................................................................................................ 574.8 show interface switchport................................................................................................................................584.9 switchport access allowed............................................................................................................................... 594.10 switchport access vlan...................................................................................................................................604.11 switchport mode access................................................................................................................................. 604.12 switchport mode trunk...................................................................................................................................614.13 switchport mode trunk ingress-filter............................................................................................................. 624.14 switchport trunk allowed...............................................................................................................................634.15 switchport trunk native..................................................................................................................................644.16 vlan bridge disable........................................................................................................................................ 65

5 Voice VLAN Commands.......................................................................................................................... 675.1 voice vlan........................................................................................................................................................ 675.2 voice vlan security enable............................................................................................................................... 685.3 voice vlan set phb to........................................................................................................................................685.4 voice vlan mac-address................................................................................................................................... 705.5 voice vlan enable.............................................................................................................................................715.6 show voice vlan state.......................................................................................................................................725.7 debug voice-vlan............................................................................................................................................. 73

6 VLAN Classification Commands............................................................................................................746.1 vlan classifier activate..................................................................................................................................... 746.2 vlan classifier group........................................................................................................................................ 756.3 vlan classifier rule........................................................................................................................................... 766.4 show vlan classifier group...............................................................................................................................786.5 show vlan classifier interface.......................................................................................................................... 79

6.6 show vlan classifier rule..................................................................................................................................806.7 show resource vlan-classification....................................................................................................................80

7 VLANMaping Commands...................................................................................................................... 827.1 ethernet evc..................................................................................................................................................... 827.2 dot1q mapped-vlan..........................................................................................................................................837.3 dot1q mapped-double-vlan..............................................................................................................................837.4 vlan mapping table.......................................................................................................................................... 847.5 raw-vlan...........................................................................................................................................................857.6 show vlan mapping table.................................................................................................................................867.7 show vlan mapping table applied-interface.....................................................................................................877.8 switchport mode.............................................................................................................................................. 887.9 switchport dot1q-tunnel type...........................................................................................................................887.10 switchport dot1q-tunnel native......................................................................................................................897.11 switchport dot1q-tunnel allow vlan...............................................................................................................907.12 switchport dot1q-tunnel vlan mapping table.................................................................................................917.13 switchport trunk vlan-translation.................................................................................................................. 927.14 switchport trunk vlan-translation mapping table...........................................................................................937.15 vlan dot1q tag native..................................................................................................................................... 947.16 show resource vlan-mapping.........................................................................................................................94

8 Link Aggregation Commands................................................................................................................. 968.1 channel-group..................................................................................................................................................968.2 static-channel-group........................................................................................................................................ 978.3 lacp port-priority............................................................................................................................................. 988.4 lacp timeout..................................................................................................................................................... 998.5 lacp system-priority.......................................................................................................................................1008.6 port-channel load-balance............................................................................................................................. 1018.7 show channel-group summary...................................................................................................................... 1028.8 show channel-group detail............................................................................................................................ 1038.9 show lacp internal..........................................................................................................................................1048.10 show lacp internal detail..............................................................................................................................1058.11 show lacp neighbor......................................................................................................................................1088.12 show lacp neighbor detail............................................................................................................................1108.13 show channel-group port............................................................................................................................. 1138.14 show lacp counters...................................................................................................................................... 1178.15 show lacp sys-id.......................................................................................................................................... 1188.16 clear lacp counters....................................................................................................................................... 119

9 MSTP Commands.................................................................................................................................... 1209.1 spanning-tree enable......................................................................................................................................1209.2 spanning-tree priority.................................................................................................................................... 1219.3 spanning-tree instance priority...................................................................................................................... 1229.4 spanning-tree forward-time........................................................................................................................... 1239.5 spanning-tree hello-time................................................................................................................................1249.6 spanning-tree max-age.................................................................................................................................. 125

9.7 spanning-tree max-hops................................................................................................................................ 1269.8 spanning-tree transmit-holdcount..................................................................................................................1279.9 spanning-tree edgeport bpdu-guard...............................................................................................................1279.10 spanning-tree edgeport bpdu-filter.............................................................................................................. 1289.11 spanning-tree port........................................................................................................................................1299.12 spanning-tree port-priority.......................................................................................................................... 1309.13 spanning-tree pathcost-standard..................................................................................................................1319.14 spanning-tree path-cost............................................................................................................................... 1329.15 spanning-tree link-type................................................................................................................................1339.16 spanning-tree edgeport................................................................................................................................ 1349.17 spanning-tree edgeport bpdu-guard.............................................................................................................1359.18 spanning-tree edgeport bpdu-filter.............................................................................................................. 1369.19 spanning-tree guard root..............................................................................................................................1379.20 spanning-tree guard loop.............................................................................................................................1389.21 spanning-tree force-version.........................................................................................................................1399.22 spanning-tree restricted-tcn......................................................................................................................... 1409.23 spanning-tree restricted-role........................................................................................................................1409.24 spanning-tree mode..................................................................................................................................... 1419.25 spanning-tree instance port-priority............................................................................................................ 1429.26 spanning-tree instance path-cost................................................................................................................. 1439.27 spanning-tree instance restricted-tcn...........................................................................................................1449.28 spanning-tree instance restricted-role..........................................................................................................1459.29 spanning-tree mst configuration..................................................................................................................1469.30 instance........................................................................................................................................................1479.31 region...........................................................................................................................................................1489.32 revision........................................................................................................................................................ 1499.33 clear spanning-tree detected protocols........................................................................................................ 1509.34 clear spanning-tree disabled-port................................................................................................................ 1509.35 show spanning-tree......................................................................................................................................1519.36 show spanning-tree interface.......................................................................................................................1529.37 show spanning-tree brief............................................................................................................................. 1549.38 show spanning-tree disabled-port................................................................................................................1559.39 show spanning-tree mst...............................................................................................................................1559.40 show spanning-tree mst config....................................................................................................................1569.41 show spanning-tree mst detail..................................................................................................................... 1579.42 show spanning-tree mst instance.................................................................................................................1599.43 show spanning-tree mst interface................................................................................................................1609.44 show spanning-tree mst brief...................................................................................................................... 1619.45 spanning-tree instance forward................................................................................................................... 162

10 Flow Control Commands......................................................................................................................16410.1 flowcontrol send..........................................................................................................................................16410.2 flowcontrol receive......................................................................................................................................16510.3 show flowcontrol.........................................................................................................................................165

11 Layer 2 Protocols Tunneling Commands.......................................................................................... 16711.1 l2protocol enable......................................................................................................................................... 16711.2 l2protocol tunnel-dmac................................................................................................................................16711.3 l2protocol mac............................................................................................................................................. 16811.4 l2protocol.....................................................................................................................................................16911.5 l2protocol uplink enable.............................................................................................................................. 17011.6 show l2protocol........................................................................................................................................... 17111.7 l2protocol cos.............................................................................................................................................. 17211.8 l2protocol full-mac...................................................................................................................................... 173

12 Storm Control Commands....................................................................................................................17512.1 storm-control............................................................................................................................................... 17512.2 show storm-control......................................................................................................................................17612.3 ipg storm-control enable..............................................................................................................................177

13 MLAG Commands.................................................................................................................................17813.1 mlag configuration...................................................................................................................................... 17813.2 peer-address.................................................................................................................................................17913.3 peer-link.......................................................................................................................................................17913.4 timers mlag..................................................................................................................................................18013.5 reload-delay.................................................................................................................................................18113.6 mlag.............................................................................................................................................................18313.7 clear mlag count.......................................................................................................................................... 18413.8 show mlag................................................................................................................................................... 18513.9 show mlag peer............................................................................................................................................18613.10 show mlag interface.................................................................................................................................. 188

7

1 Interface Commands

1.1 bandwidthUse this command to set the bandwidth of the port.

To return the bandwidth to default value, use the no form of this command.

Command Syntax

bandwidth bandwidth

no bandwidth

bandwidth port bandwidth, in kilobits

Command Mode

Interface Configuration

Default

None

Usage

None

Examples

The following example set the bandwidth of the port:

Switch(config)# interface eth-0-1

Switch(config-if)# bandwidth 1000

The following example returns the bandwidth to default value:

8

Switch(config-if)# no bandwidth

Related Commands

duplex

speed

1.2 clear countersUse this command to clear the counters on the physical interface.

Command Syntax

clear counters (IFNAME |)

IFNAME Only clear the specified interface statistics

Command Mode

Privileged EXEC

Default

None

Usage

The clear counters command clears all current interface counters from the interface unless you specifyoptional arguments that clear only a specific interface type from a specific interface number.

Examples

The following example clears the counters on all interfaces:

Switch# clear counters

The following example clears the counters on the interface eth-0-1:

Switch# clear counters eth-0-1

9

The following example clears the counters on the agg1:

Switch# clear counters agg1

Related Commands

None

1.3 descriptionUse this command to set the description on the interface.

To remove the description on the interface, use the no form of this command.

Command Syntax

description LINE

no description

LINE The description on the interface, should be no more than 20 characters, andthe character must be “0-9A-Za-z.-_” with alphabet as prefix

Command Mode


Default

None

Usage

None

Examples

The following example sets the description on the interface:


Switch(config-if)# description Ethernet

The following example removes the description on the interface:

10

Switch(config-if)# no description

Related Commands

None

1.4 duplexUse the duplex interface configuration command to specify the duplex mode of operation for a port.Use the no form of this command to return the port to its default value.

Command Syntax

duplex (auto |full |half)

no duplex

auto Enable automatic duplex configuration; port automatically detects whether itshould run in full-duplex or half-duplex mode, depending on the attacheddevice mode

full Enable full-duplex mode

half Enable half-duplex mode (only for interfaces operating at 10 or 100 Mb/s).You can not configure half-duplex mode for interfaces operating at 1000or10,000 Mb/s

Command Mode


Default

Auto

Usage

The command is not allowed to be set on 10G port or optical mode of combo port.

Examples

The following example sets the duplex mode to auto:


11

Switch(config-if)# duplex auto

The following example sets the duplex mode to full:

Switch(config-if)# duplex full

The following example returns the duplex mode to default:

Switch(config-if)# no duplex

Related Commands

bandwidth

speed

1.5 speedUse the speed interface configuration command to specify the speed of a 10/100 Mb/s or 10/100/1000Mb/s port. Use the no of this command to return the port to its default value.

Command Syntax

speed (10 |100 |1000 |auto)

no speed

auto Port automatically detects the speed it should run

10 Port runs at 10 Mb/s



Command Mode


Default

Auto

12

Usage

The command is not allowed to be set on 10G port or optical mode of combo port.

Examples

This example shows how to set the speed on a port to 1000 Mb/s:


Switch(config-if)# speed 1000

This example shows how to return the speed on a port to default value:

Switch(config-if)# no speed

Related Commands

bandwidth

duplex

1.6 flowcontrolUse the flowcontrol interface configuration command to control the packet flow.

Command Syntax

flowcontrol (send|receive) (on|off)

send Input direction

receive Ouput direction

on Enable flow control

off Disable flow control

Command Mode


13

Default

Disabled

Usage

By default, flow control is disabled.

Examples

The following example sets the flow control on in the tx direction:


Switch(config-if)# flowcontrol send on

The following example sets the flow control on in the rx direction:

Switch(config-if)# flowcontrol receive on

Related Commands

None

1.7 interfaceUse this command to enter interface mode.

Command Syntax

interface IFNAME

IFNAME The name of interface, i.e. eth-0-1, agg1, vlan1,loopback1

Command Mode

Global Configuration

Default

None

14

Usage

The interface name can be either a port name (i.e. eth-0-1) or link-agg name (i.e. agg1) or vlan name(i.e. vlan2) or loop-back name (i.e. loopback10).

Examples

The following example enters the interface mode for eth-0-1:


The following example enters the interface mode for agg1:

Switch(config)# interface agg1

The following example enters the interface mode for vlan2:

Switch(config)# interface vlan2

Related Commands

exit

1.8 interface rangeUse this command to operate a list of interfaces, the interface include physical port, vlan interface,linkagg interface and loopback interface.

Command Syntax

interface range IFNAME

IFNAME Interface range, can be separate by comma, dash

Command Mode


Default

None

15

Usage

None

Examples

The following example operate a list of physical interface:

Switch(config)# interface range eth-0-1 – 24

Switch(config-if-range)# shutdown

The following example operate a list of vlan interface:

Switch(config)# interface range vlan 1 - 20


The following example operate a list of linkagg interface:

Switch(config)# interface range agg 10 - 20


The following example operate a list of loopback interface:

Switch(config)# interface range loopback 0 - 5


Related Commands

None

1.9 interface range create vlanUse this command to create a list of vlan interface.

Command Syntax

interface range create vlan vid-range

vid-range VLAN ID range, can be separate by comma, dash

16

Command Mode


Default

None

Usage

None

Examples

The following example create vlan interface 10 to 20:

Switch(config)# interface range create vlan 10 - 20


Related Commands

None

1.10 jumboframeUse this command to enable jumbo frame. To disable jumbo frame, use the no form of this command.

Command Syntax

jumboframe enable

no jumboframe enable

Command Mode


Default

Default is disabled.

17

Usage

Jumboframe is disabled by default. The max frame which can be transmitted is 1534 bytes. Whenenable jumboframe, the max frame can be 9600 bytes.

Examples

The following example enables the jumboframe:


Switch(config-if)# jumboframe enable

The following example disables the jumboframe:

Switch(config-if)# no jumboframe enable

Related Commands

None

1.11 system jumboframe sizeUse this command to set jumbo frame size.

To return to default jumbo frame size, use the no form of this command.

Command Syntax

system jumboframe size SIZE

no system jumboframe size

SIZE Frame size of max jumbo frame, the range is 9216~16096

Command Mode


Default

9600

18

Usage

When jumboframe is enable, by default, the max frame size which can be transmitted is 9600 bytes.Use this command this set the max frame size.

Examples

The following example shows how to set the max jumboframe size:

Switch(config)# system jumboframe size 16906

Related Commands

jumboframe

1.12media-typeUse the media-type interface configuration command to select a media type for an interface. Use the noform of this command restore to the default value.

Command Syntax

media-type (auto-select|rj45|sfp)

no media-type

auto-select Enable the switch to dynamically select the type based on which one first linksup

rj45 Select the RJ-45 interface

sfp Select the small form-factor pluggable (SFP) module interface

Command Mode


Default

Auto-select

Usage

By default, we use auto-select mode.

19

Examples

The following example shows how to configure the interface as a rj45 media:


Switch(config-if)# media-type rj45

The following example shows how to restore to default value:

Switch(config-if)# no media-type

Related Commands

None

1.13 shutdownUse the shutdown interface configuration command to admin down an interface. Use the no form ofthis command to admin up an interface.

Command Syntax

shutdown

no shutdown

Command Mode


Default

None

Usage

None

Examples

The following example shows how to shutdown a port:


Switch(config-if)# shutdown

20

The following example shows how to admin up a port:

Switch(config-if)# no shutdown

Related Commands

None

1.14 load-intervalUse the load-inteval interface configuration command to specify the interval when calculating speed ofan interface. Use the no of this command to return the port to its default value.

Command Syntax

load-interval seconds

no load-interval

seconds Load interval in seconds, the range is 30~600

Command Mode


Default

300 seconds

Usage

Load-interval must be in increments of 30 second and its default value is 300 second.

Examples

This example shows how to set the load-interval on a port to 600 second:


Switch(config-if)# load-interval 600

21

This example shows how to return the load-interval on a port to default value:

Switch(config-if)# no load-interval

Related Commands

show interface

1.15 vlan dot1q tag nativeUse the vlan dot1q tag native global configuration command to configure the edge switch so that allpackets going out an 802.1Q trunk, including the native VLAN.

Command Syntax

vlan dot1q tag native

no vlan dot1q tag native

Command Mode


Default

None

Usage

If the switch is configured to tag native VLAN packets on all 802.1Q trunks, the switch acceptsuntagged packets, but sends only tagged packets. By default, vlan dot1q tag native is disabled.

Examples

This example shows how to tag native for trunk port:


Switch(config-if)# vlan dot1q tag native

This example shows how to disable tagging native for trunk port:

Switch(config-if)# no vlan dot1q tag native

22

Related Commands

None

1.16 show interfaceUse this command to display the configurations and statistics on all interfaces or an interface.

Command Syntax

show interface (IFNAME | )

IFNAME The interface name, can be eth, vlan or agg

Command Mode

Privileged EXEC

Default

None

Usage

None

Examples

This example shows how to display the configurations and statistics on the interface eth-0-1.

Switch# show interface eth-0-1

Interface eth-0-1

Interface current state: Administratively DOWN

Hardware is Ethernet, address is bc3e.60b2.1601 (bia bc3e.60b2.1601)

Bandwidth 1000000 kbits

Index 1 , Metric 1 , Encapsulation ARPA

Speed - 1000Mb/s , Duplex - Full , Media type is 1000BASE_T

Link speed type is autonegotiation, Link duplex type is autonegotiation

Input flow-control is off, output flow-control is off

The Maximum Frame Size is 1534 bytes

VRF binding: not bound

Label switching is disabled

No virtual circuit configured

ARP timeout 01:00:00, ARP retry interval 1s

23

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes

Received 0 unicast, 0 broadcast, 0 multicast

0 runts, 0 giants, 0 input errors, 0 CRC

0 frame, 0 overrun, 0 pause input

0 input packets with dribble condition detected

0 packets output, 0 bytes

Transmitted 0 unicast, 0 broadcast, 0 multicast

0 underruns, 0 output errors, 0 pause output

Related Commands

show interface status

1.17 show interface statusUse this command to display the brief information on all Ethernet and link aggregation interfaces.

Command Syntax

show interface (IFNAME| ) status

IFNAME The interface name, can be eth, agg

Command Mode

Privileged EXEC

Default

None

Usage

This command will not show VLAN and tunnel interfaces’ information.

Examples

This example shows how to display the brief information on all Ethernet and LAG interfaces:

Switch# show interface status

Port Status Duplex Speed Mode Type Description

-----------------------------------------------------------------

24

eth-0-1 down a-full a-1000 ACCESS 1000BASE_T


eth-0-3 admin down auto auto ACCESS 1000BASE_T


eth-0-5 up a-full a-1000 routed 1000BASE_T

eth-0-6 up a-full a-100 ACCESS 1000BASE_T















Related Commands

None

1.18 show interface summaryUse this command to display the summary on all interfaces or an interface.

Command Syntax

show interface (IFNAME|) summary

IFNAME The interface name

Command Mode

Privileged EXEC

Default

None

25

Usage

This command will display the summary on all interfaces or an interface in the form of list.

Examples

This example shows how to display the summary on the interface eth-0-1.

Switch# show interface eth-0-1 summary

RXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)

TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)

Interface Link RXBS RXPS TXBS TXPS

-----------------------------------------------------------------------------

eth-0-1 DOWN 2 0 0 0

Related Commands

show interface

1.19 show ip interfaceUse this command to show layer3 interface information.

Command Syntax

show ip interface (IFNAME|)

show ip interface brief

IFNAME The interface name, can be eth, vlan or agg

Command Mode

Privileged EXEC

Default

None

Usage

None

26

Examples

This example shows the vlan interface information:

Switch# show interface vlan10

Interface vlan10

Interface current state: DOWN

Hardware is VLAN, address is 8633.d260.6500 (bia 8633.d260.6500)

Bandwidth 1000000 kbits

Index 4098 , Metric 1 , Encapsulation ARPA

The maximum transmit unit (MTU) is 1500 bytes

VRF binding: not bound

Label switching is disabled

No virtual circuit configured

VRRP master of : VRRP is not configured on this interface

ARP timeout 01:00:00, ARP retry interval 1s

Related Commands

None

1.20 switchportUse this command to configure a port to a bridge (layer 2) or routing (layer 3) mode.

Command Syntax

switchport

no switchport

Command Mode


Default

Switchport

Usage

When using this command to change the mode of a port, all bridge or routing configurations of this portwill be cleared and not restored. By default, the port is a switchport.

27

Examples

This example shows how to configure a port to bridge mode:


Switch(config-if)# switchport

This example shows how to configure a port to routing mode:

Switch(config-if)# no switchport

Related Commands

None

1.21 switchport access allowedUse this command to configure whether the specified VLAN flow can pass this access port.

Command Syntax

switchport access allowed vlan (add | ove) vid

add Allow the specified VLAN packet pass through this port

remove Forbid the specified VLAN packet pass through this port

vid VLAN ID

Command Mode


Default

None

Usage

This command is used for vlan classification or dot1x guest vlan.

28

Examples

This example shows how to configure the specified VLAN flow pass through the port:


Switch(config-if)# switchport access allowed vlan add 10

Related Commands

switchport trunk allowed vlan (add vid | remove vid| all | none)

1.22 switchport access vlanUse this command to set the default VLAN for access port.

Command Syntax

switchport access vlan vid

no switchport access vlan

vid VLAN ID

Command Mode


Default

1

Usage

Before this command is used, port must be set to access port. By default, VLAN should be 1.

Examples

This example shows how to configure the access port to add to default vlan 10:


Switch(config-if)# switchport mode access

Switch(config-if)# switchport access vlan 10

29

This example shows how to configure the access port to restore to default vlan 1:

Switch(config-if)# no switchport access vlan

Related Commands

switchport trunk native

1.23 switchport mode accessUse this command to configure the port work in access mode.

Command Syntax

switchport mode access

Command Mode


Default

Access port

Usage

When port mode changed, all the dynamic FDB will be cleared.

Examples

This example shows how to configure the port to access mode.



Related Commands

switchport mode trunk

1.24 switchport mode trunkUse this command to configure the port work in trunk mode.

30

Command Syntax


Command Mode


Default

Access port

Usage


Examples

This example shows how to configure the port to trunk mode.


Switch(config-if)# switchport mode trunk

Related Commands


1.25 switchport mode dot1q-tunnelUse this command to configure the port as QINQ port.

Command Syntax

switchport mode dot1q-tunnel

Command Mode


Default

Access Port

31

Usage


Examples

This example shows how to configure the port to QINQ mode.


Switch(config-if)# switchport mode dot1q-tunnel

Related Commands


1.26 switchport mode trunk ingress-filterUse this command to enable or disable VLAN ingress filter.

Command Syntax

switchport mode trunk ingress-filter (enable|disable)

enable Enable the VLAN ingress filter

disable Disable the VLAN ingress filter

Command Mode


Default

Ingress filter Enabled

Usage

This command should only be used with trunk port. If ingress filter check enabled, the port should onlyreceive packet of allowed VLANs; otherwise if ingress filter check disabled, the port should allowpacket of all VLANs.

32

Examples

This example shows how to configure enable vlan ingress filter.



Switch(config-if)# switchport mode trunk ingress-filter enable

Related Commands


1.27 switchport trunk allowedUse this command to configure whether the specified VLAN flow can pass this trunk port.

Command Syntax

switchport trunk allowed vlan (add vid | remove vid | all | none)

add vid Allow the specified VLAN flow pass through this port

remove vid Forbid the specified VLAN flow pass through this port

all Allow all the VLAN flow pass through this port

none Forbid all the VLAN flow pass through this port

Command Mode


Default

1

Usage

None

Examples

This example shows how to configure the specified VLAN flow pass through the port:

33


Switch(config-if)# switchport trunk allowed vlan add 10

This example shows how to configure the all VLAN flow pass through the port:

Switch(config-if)# switchport trunk allowed vlan all

This example shows how to configure the all VLAN flow can not pass through the port:

Switch(config-if)# switchport trunk allowed vlan none

Related Commands

switchport access allowed vlan (add｜remove) vid

1.28 switchport trunk nativeUse this command to configure the default VLAN for this trunk port.

Command Syntax

switchport trunk native vlan vid

vid VLAN ID, range is 2-4094

Command Mode


Default

1

Usage

Before this command is used, port must be set to trunk port.

Examples

This example shows how to configure default vlan 10 for trunk port:

34



Switch(config-if)# switchport trunk native vlan 10

Related Commands

switchport access vlan vid

35

2 Interface Errdisable Commands

2.1 errdisable detectUse the interface errdisable detects configuration command to enable errdisable detection. Use the noform of this command to disable errdisable detection.

Command Syntax

errdisable detect reason (link-flap | udld | fdb-loop)

no errdisable detect reason (link-flap | udld | fdb-loop)

link-flap Enable detect Link flap error

udld Enable detect UDLD error

fdb-loop Enable detect FDB loop error

Command Mode


Default

Enabled

Usage

Only the link flap can be configured, other errdisable reason can not be configured.

Examples

This example shows how to enable errdisable detect link flap:

Switch(config)# errdisable detect reason link-flap

36

This example shows how to disable errdisable detect link flap:

Switch(config)# no errdisable detect reason link-flap

Related Commands

show errdisable detect

2.2 errdisable recovery intervalUse this command to set the specified timer to recover from the errdisable state. Use the no form of thiscommand to restore to the default interval.

Command Syntax

errdisable recovery interval RANGE

no errdisable recovery interval

RANGE Recovery interval range in seconds, from 30~86400

Command Mode


Default

300

Usage

The change of interval will not affect already started errdisable recovery timer.

Examples

This example shows how to set errdisable recovery to 30 seconds.

Switch(config)# errdisable recovery interval 30

This example shows how to set errdisable recovery to default values.

Switch(config)# no errdisable recovery interval

37

Related Commands

errdisable recovery reason

show errdisable recovery

2.3 errdisable recovery reasonUse this command to enable error disable detection for a specified cause or all cause. Use the no formof this command to disable the error disable feature.

Command Syntax

errdisable recovery reason (all|bpduguard | bpduloop| port-security|link-flap|link-monitor-failure | oam-remote-failure|udld| fdb-loop)

no errdisable recovery reason (all|bpduguard | bpduloop| port-security|link-flap|link-monitor-failure | oam-remote-failure|udld| fdb-loop)

all Enable timer to recover from all reason

bpduguard Enable timer to recover from BPDU Guard error disable state

bpduloop Enable timer to recover from BPDU Loopback error disable state

port-security Enable timer to recover from Port security failure

link-flap Enable timer to recover from Link flap failure

link-monitor-failure Enable timer to recover from link monitoring failure

oam-remote-failure Enable timer to recover from OAM detected remote failure

udld Enable timer to recover from UDLD failure

fdb-loop Enable timer to recover from FDB loop

Command Mode


Default

Disabled

Usage

The change of reason will not affect those interfaces have already enter errdisable state.

38

Examples

This example shows how to enable link flap errdisable recovery:

Switch(config)# errdisable recovery reason link-flap

This example shows how to disable link flap errdisable recovery:

Switch(config)# no errdisable recovery reason link-flap

Related Commands

errdisable recovery interval


2.4 errdisable flapUse this command to set the parameters for link-flap error disable. Use the no form of this command torestore to default value.

Command Syntax

errdisable flap reason link-flap count seconds

no errdisable flap reason link-flap

link-flap Configure link flap conditions

count Max flap count, the range is 1~100

seconds Flap count time in seconds, the range is 1~120

Command Mode


Default

count = 10, seconds = 10

39

Usage

Only the link flap can be detected. is the threshold of flap count, and is the counttime in seconds for flap count. If the errdisable detect link flap is enabled, will result in link flaperrdisable, otherwise, will only print a message in log.

Examples

This example shows how to set link flap conditions to 20 times in 60 seconds:

Switch(config)# errdisable flap reason link-flap 20 60

This example shows how to disable link flap conditions to default:

Switch(config)# no errdisable flap reason link-flap

Related Commands

show errdisable flap

2.5 show errdisable detectUse this command to display the error disable detection reason.

Command Syntax

show errdisable detect

Command Mode

Privileged EXEC

Default

None

Usage

None

Examples

Switch# show errdisable detect

ErrDisable Reason Detection status

40

----------------- ----------------

bpduguard Enabled

bpduloop Enabled

link-monitor-failure Enabled

oam-remote-failure Enabled

port-security Enabled

link-flap Enabled

monitor-link Enabled

udld Enabled

fdb-loop Enabled

Related Commands

errdisable detect

2.6 show errdisable recoveryUse this command to display the error disable recovery timer.

Command Syntax


Command Mode

Privileged EXEC

Default

None

Usage

None

Examples

Switch# show errdisable recovery

ErrDisable Reason Timer Status

----------------- --------------

bpduguard Disabled

bpduloop Disabled

link-monitor-failure Disabled

oam-remote-failure Disabled

port-security Disabled

link-flap Enabled

udld Disabled

41

Timer interval: 300 seconds

Related Commands

errdisable recovery interval

errdisable recovery reason

2.7 show errdisable flapUse this command to display error disable link flap parameters.

Command Syntax

show errdisable flap

Command Mode

Privileged EXEC

Default

None

Usage

None

Examples

Switch# show errdisable flap

ErrDisable Reason Flaps Time (sec)

----------------- ------ ----------

link-flap 10 10

Related Commands

errdisable flap

42

3 MACAddress Table Commands

3.1mac-address-table ageing-timeUse the mac-address-table aging-time global configuration command on the switch to set the length oftime that a dynamic entry remains in the MAC address table after the entry is used or updated. Use theno form of this command to return to the default setting. The aging time applies to all VLANs.

Command Syntax

mac-address-table ageing-time ageing-time

no mac-address-table ageing-time

ageing-time Aging time in seconds. The range is 10 to 1000000 seconds

Command Mode


Default

The default is 300 seconds

Usage

If packets are not received continuously, user can increase the aging time to make the system recordingthe dynamic entries for a longer time. Increasing the time can reduce the possibility of flooding whenthe hosts send again.

Examples

This example shows how to set the aging time to 200 seconds for all VLANs.

Switch(config)# mac-address-table ageing-time 200

43

Related Commands

show mac address-table ageing-time

3.2mac-address-table forwardUse the mac-address-table forward global configuration command on the switch to add static addressesto the MAC address table. Use the no form of this command to remove static entries from the table.

Command Syntax

mac-address-table mac-addr forward interface-id vlan vlan-id

no mac-address-table mac-addr forward interface-id vlan vlan-id

mac-addr Destination MAC address (unicast or multicast) to add to the address table.Packets with this destination address received in the specified VLAN areforwarded to the specified interface

interface-id Interface to which the received packet is forwarded. Valid interfaces includephysical ports and link aggregation ports

vlan-id Specify the VLAN for which the packet with the specified MAC address isreceived. The range is 1 to 4094

Command Mode


Default

None

Usage

The static address entries which are added by this command are not aged.

Examples

This example shows how to add the static address c2f3.220a.12f4 to the MAC address table. When apacket is received in VLAN 4 with this MAC address as its destination, the packet is forwarded to thespecified interface:

Switch(config)# mac-address-table c2f3.220a.12f4 forward eth-0-1 vlan 4

44

Related Commands

show mac address-table

3.3mac-address-table discardUse the mac-address-table discard global configuration command on the switch to enable unicast MACaddress filtering and to configure the switch to drop traffic with a specific source or destination MACaddress. Use the no form of this command to return to the default setting.

Command Syntax

mac-address-table mac-addr discard

no mac-address-table mac-addr discard

mac-addr Source or Destination MAC address (unicast) to add to the address filteringtable

Command Mode


Default

None

Usage

Follow these guidelines when using this feature:

Multicast MAC addresses, broadcast MAC addresses, and router MAC addresses are not supported.Packets that are forwarded to the CPU are also not supported.

Examples

This example shows how to enable unicast MAC address filtering and to configure the switch to droppackets that have a source or destination address of c2f3.220a.12f4.When a packet is received with thisMAC address as its source or destination, the packet is dropped:

Switch(config)# mac-address-table c2f3.220a.12f4 discard

Related Commands

mac-address-table forward

45

3.4 clear mac address-tableUse the clear mac address-table privileged EXEC command on the switch to delete a specific dynamicaddress, all dynamic addresses on a particular interface, all dynamic addresses on stack members, or alldynamic addresses on a particular VLAN from the MAC address table.

Command Syntax

clear mac address-table (static | dynamic| multicast) (address mac-addr | interface interface-id |vlan vlan-id)

dynamic Delete the dynamic MAC address

static Delete the static MAC address

multicast Delete the multicast MAC address

address mac-addr Delete the specified MAC address

interfaceinterface-id

Delete all MAC addresses on the specified physical port or link aggregationport

vlan vlan-id Delete all MAC addresses for the specified VLAN. The range is 1 to 4094

Command Mode

Privileged EXEC

Default

None

Usage

None

Examples

This example shows how to remove a specific MAC address from the dynamic address table:

Switch# clear mac address-table dynamic address 0008.0070.0007

Related Commands


46

3.5 show mac address-table ageing-timeUse the show mac address-table ageing-time privileged EXEC command to display the aging time ofall address table instances on all VLANs.

Command Syntax

show mac address-table ageing-time

Command Mode

Privileged EXEC

Default

None

Usage

None

Examples

This is an example of output from the show mac address-table ageing-time command:

Switch# show mac address-table ageing-time

MAC address table ageing time is 300 seconds

Related Commands

mac-address-table ageing-time

3.6 show mac address-tableUse the show mac address-table privileged EXEC command to display a specific MAC address tablestatic and dynamic entry or the MAC address table static and dynamic entries on a specific interface orVLAN.

Command Syntax

show mac address-table (dynamic | static | multicast | ) (address mac-addr | interface interface-id |vlan vlan-id | )

47

dynamic Display the dynamic MAC address

static Display the static MAC address

multicast Display the multicast MAC address

address mac-addr Display the specified MAC address

interfaceinterface-id

Display all MAC addresses on the specified physical port or link aggregationport

vlan vlan-id Display all MAC addresses for the specified VLAN. The range is 1 to 4094

Command Mode

Privileged EXEC

Default

None

Usage

None

Examples

This is an example of output from the show mac address-table command:

Switch# show mac address-table

Mac Address Table

-------------------------------------------

(*) - Security Entry

Vlan Mac Address Type Ports

---- ----------- -------- -----

1 0000.0000.0001 static eth-0-2

1 0000.0001.0003 static(*) eth-0-1

1 0000.0001.0002 static(*) eth-0-1

2 26fc.72e5.0100 dynamic(*) eth-0-9

1 0100.0000.0001 static eth-0-2

eth-0-1

Related Commands

mac-address-table

48

3.7 show mac address-table countUse the show mac address-table count privileged EXEC command to display the number of addressespresent in all VLANs.

Command Syntax

show mac address-table count

Command Mode

Privileged EXEC

Default

None

Usage

None

Examples

This is an example of output from the show mac address-table count command:

Switch# show mac address-table count

Dynamic Address Count : 1 (Security: 0)

Static Address Count : 1 (Security: 0)

Total Mac Addresses : 2 (Security: 0)

Related Commands


3.8 show mac-filter address-tableUse the show mac-filter address-table privileged EXEC command to display the number of filteraddresses present in all VLANs.

Command Syntax

show mac-filter address-table

49

Command Mode

Privileged EXEC

Default

None

Usage

None

Examples

This is an example of output from the show mac-filter address-table command:

Switch# show mac-filter address-table

MAC Filter Address Table

----------------------------------

Current count : 1

Max count : 256

Left count : 255

Filter address list :

----------------------------------

0000.000a.000a

Related Commands


3.9 show resource mac-filterUse this command to display the resource statistic used by mac-filter.

Command Syntax

show resource mac-filter

Command Mode

Privileged EXEC

Default

None

50

Usage

None

Examples

The following is sample output from the show resource mac-filter command.

Switch# show resource mac-filter

MAC-FILTER

Resource Used Capability

=============================================================

Blackhole MAC Addresses 0 256

Related Commands

show resource static-fdb

3.10 show resource static-fdbUse this command to display the resource statistic used by static FDB.

Command Syntax

show resource static-fdb

Command Mode

Privileged EXEC

Default

None

Usage

None

Examples

The following is sample output from the show resource static-fdb command:

Switch# show resource static-fdb

STATIC-FDB

Resource Used Capability

=============================================================

51

Static FDB 0 1024

Related Commands

show resource mac-filter

52

4 VLAN Commands

4.1 vlan databaseUse this command to enter VLAN configure mode.

Command Syntax

vlan database

Command Mode


Default

None

Usage

When you try to create or remove VLAN, you must use this command to enter VLAN configure modefirst. To exit VLAN configure mode, use exit command.

Examples

This example shows how to enter VLAN configure mode:

Switch(config)# vlan database

Switch(config-vlan)#

This example shows how to exit VLAN configure mode:

Switch(config-vlan)# exit

Switch(config)#

53

Related Commands

exit

4.2 vlan replace dscpUse this command to enable DSCP on specific VLAN.

To disable it, use the no form of this command.

Command Syntax

vlan vlan replace dscp-exp

no vlan vlan replace dscp-exp

vlan vlan id

Command Mode

VLAN Configuration

Default

None

Usage

This command is enabled the DSCP of the packet in the VLAN will be replaced.

Examples

This example shows how to enable dscp on VLAN 1:

Switch(config-vlan)# vlan 1 replace dscp-exp

This example shows how to disable dscp on VLAN 1:

Switch(config-vlan)# no vlan 1 replace dscp-exp

Related Commands

qos enable

54

4.3 vlanUse the vlan VLAN configuration command to configure VLAN characteristics for a VLAN in theVLAN database. Use the no form of this command to delete a VLAN.

Command Syntax

vlan vlan (name name|) (state (enable |disable)|)

no vlan vlan

vlan Vlan id, the range is 1~4094

name name the name for specific vlan, no more than 16 characters

enable set the operational state of the VLAN to enable, and it is enabled by default

disable set the operational state of the VLAN to disable

Command Mode

VLAN Configuration

Default

VLAN 1 is the default VLAN and all ports have been added to it by default.

Usage

Default VLAN 1 can not be removed.

Examples

This example shows how to create VLAN 11 and named it to “vlan11”:

Switch(config-vlan)# vlan 11 name vlan11 state enable

This example shows how to remove VLAN 11:

Switch(config-vlan)# no vlan 11

Related Commands

vlan VLAN_LIST

55

show vlan vlan

show vlan all

4.4 vlan VLAN_LISTUse the vlan VLAN_LIST configuration command to add a normal-range VLANs to the VLANdatabase.

Command Syntax

vlan VLAN_LIST

no vlan VLAN_LIST

VLAN_LIST vlan list connected with ‘-’ and ‘,’, for example, “1-10,15,20,30-40”

Command Mode

VLAN Configuration

Default

Vlan 1 is the default vlan and all ports have been added to it by default.

Usage

The vlan list should be connected with ‘-’ and ‘,’, the value should be in the range of andshould be ascending order.

Default VLAN 1 can not be removed.

Examples

This example shows how to add vlans of “100,200,300-400”:

Switch(config-vlan)# vlan 100,200,300-400

This example shows how to remove vlans of “100,200,300-400”:

Switch(config-vlan)# no vlan 100,200,300-400

56

Related Commands

vlan

show vlan vlan

show vlan all

4.5 show vlanUse this command to display specific vlan information.

Command Syntax

show vlan vlan


Command Mode

Privileged EXEC

Default

None

Usage

This command is used to display VLAN property includeing name, state, stp id, DSCP, member ports.

Examples

This example shows how to display the information on VLAN 11:

Switch# show vlan 11

Related Commands

show vlan all

4.6 show vlan allUse this command to show the information of all the VLAN.

57

Command Syntax

show vlan all

Command Mode

Privileged EXEC

Default

None

Usage

This command is used to display all VLAN property includeing name, state, stp id, DSCP, memberports.

Examples

This example shows how to display the information on VLAN all:

Switch# show vlan all

Related Commands

show vlan vlan

4.7 show vlan briefUse this command to show the brief information on VLAN.

Command Syntax

show vlan brief

Command Mode

Privileged EXEC

Default

None

Usage

This command is used to display all VLAN information for all bridges, including static and dynamic.

58

Examples

This example shows how to display the brief information on VLAN:

Switch# show vlan brief

Related Commands

show vlan vlan

4.8 show interface switchportUse this command to show the vlan configurations on all bridge ports or a bridge port.

Command Syntax

show interface switchport (interface IFNAME|)

IFNAME Interface name

Command Mode

Privileged EXEC

Default

None

Usage

This command is used to display one or all VLAN’s L2 configurations.

Examples

This example shows how to display the vlan configurations on all bridge ports or a bridge port:

Switch# show interface switchport interface eth-0-1

Related Commands



59

4.9 switchport access allowedUse this command to allow or not allow the traffic from the specific VLAN to pass the access port.

Command Syntax

switchport access allowed vlan (add | remove) vlan

add Allow the traffic from the vlan to pass the access port

remove Not allow the traffic from the vlan to pass the access port

vlan Vlan list connected with ‘-’ and ‘,’, for example, “1-10,15,20,30-40”

Command Mode


Default

None

Usage

This command is used to allow the traffic from the specific VLAN to pass the access port.

Examples

This example shows how to allow the traffic from the vlan11 to pass the port:

Switch(config-if)# switchport access allowed vlan add 11

This example shows how to refuse the traffic from the vlan12 to pass the port:

Switch(config-if)# switchport access allowed vlan remove 12

Related Commands

switchport trunk allowed

60

4.10 switchport access vlanUse this command to set the access port to a specified VLAN.

To set the access port to default VLAN 1, use no form of this command.

Command Syntax

switchport access vlan vlan

no switchport access vlan


Command Mode


Default

All the ports are added to vlan 1 by default

Usage

The port should be an access port by switchport mode access command before add to vlan by thiscommand.

Examples

This example shows how to add the port to vlan 11:

Switch(config-if)# switchport access vlan 11

This example shows how to return the port to default vlan 1:

Switch(config-if)# no switchport access vlan.

Related Commands


4.11 switchport mode accessUse this command to set the switchport mode to access.

61

Command Syntax


Command Mode


Default

None

Usage

The access mode is usually used to connect the port to a terminal device, such as a PC.

When the mode is changed, both the MAC learnt dynamically and configured statically on the port willbe cleared.

Examples

This example shows how to set the switchport mode to access:


Related Commands


4.12 switchport mode trunkUse this command to set the switchport mode to trunk. Use the switchport mode access command to setthe switchport mode to default.

Command Syntax


Command Mode


Default

None

62

Usage

The trunk mode is usually used to connect the port with other switch.

The trunk mode is can also used to connect the port with host device.

When the mode is changed, both the MAC learnt dynamically and configured statically on the port willbe cleared.

Examples

This example shows how to set the switchport mode to trunk:


Related Commands


4.13 switchport mode trunk ingress-filterUse this command to set ingress-filter configuration of the trunk port.

Command Syntax

switchport mode trunk ingress-filter (enable |disable)

enable Enable the ingress-filter

disable Disable the ingress-filter

Command Mode


Default

Enable

Usage

The trunk port ingress-filter configuration should only be allowed on a trunk port.

When the ingress-filter is disabled, this port will not check the VLAN ID of received ingress packets.

63

Examples

This example shows how to set the trunk port ingress-filter to disable.

Switch(config-if)# switchport mode trunk ingress-filter disable

Related Commands


4.14 switchport trunk allowedUse this command to allow traffic from specified VLAN to transmit the trunk port.

To remove this setting, use the no form of this command.

Command Syntax

switchport trunk allowed vlan (add vlan | remove vlan | all | none)

no switchport trunk

add vlan allow the traffic from the specified vlan to transmit the trunk port. Vlan listconnected with ‘-’ and ‘,’, for example, “1-10,15,20,30-40”

remove vlan do not allow the traffic from the specified vlan to transmit the trunk port. Vlanlist connected with ‘-’ and ‘,’, for example, “1-10,15,20,30-40”

all allow the traffic from all the vlan to transmit the trunk port

none do not allow the traffic from all the vlan to transmit the trunk port

Command Mode


Default

None

Usage

This command is used to allow traffic from specified VLAN to transmit the trunk port.

Examples

This example shows how to allow traffic from vlan11,12 to transmit the trunk port:

64

Switch(config-if)# switchport trunk allowed vlan add 11,12

This example shows how to refuse traffic from vlan11,12 to transmit the trunk port:

Switch(config-if)# switchport trunk allowed vlan remove 11,12

This example shows how to allow traffic from all vlan to transmit the trunk port:

Switch(config-if)# switchport trunk allowed vlan all

This example shows how to refuse traffic from all vlan to transmit the trunk port:

Switch(config-if)# switchport trunk allowed vlan none

Related Commands

switchport access allowed

4.15 switchport trunk nativeUse this command to set the native VLAN for sending and receiving untagged traffic.

To return the native VLAN to default value, use the no form of this command.

Command Syntax

switchport trunk native vlan vlan

no switchport trunk native vlan

vlan An existing Vlan id, the range is 2~4094

Command Mode


Default

vlan 1

65

Usage

This command is used to set the native VLAN for sending and receiving untagged traffic.

Examples

This example shows how to set the native vlan to vlan 10 on the interface:

Switch(config-if)# switchport trunk native vlan 10

This example shows how to return the native vlan to default on the interface:

Switch(config-if)# no switchport trunk native vlan

Related Commands

switchport trunk allowed

4.16 vlan bridge disableUse this command to disable bridge function on specific VLAN.To enable it, use the no form of thiscommand.

Command Syntax

vlan vlan bridge disable

no vlan vlan bridge disable


Command Mode

VLAN Configuration

Default

Vlan bridge enable

Usage

None

66

Examples

This example shows how to disable bridge function on VLAN 2:

Switch(config-vlan)# vlan 2 bridge disable

This example shows how to enable bridge function on VLAN 2:

Switch(config-vlan)# no vlan 2 bridge disable

Related Commands

None

67

5 Voice VLAN Commands

5.1 voice vlanUse this command to specific VLAN as VOICE VLAN.

Command Syntax

voice vlan vlan_id

no voice vlan

vlan_id Vlan id, the range is 2~4094

Command Mode


Default

Voice VLAN is disable

Usage

This command is enabled VOICE VLAN.

Examples

This example shows how to enable VLAN 2 as VOICE VLAN:

Switch(config)# voice vlan 2

Related Commands

qos enable

68

5.2 voice vlan security enableUse this command to enable VOICE VLAN security.

Command Syntax

voice vlan security enable

no voice vlan security enable

Command Mode


Default

By default the mode is security

Usage

If the security is enable, all the packet whose MACmismatch with OUI will be drop in VOICE VLAN.

Examples

This example shows how to enable security:

Switch(config)# voice vlan security enable

Related Commands

show voice vlan state

5.3 voice vlan set phb toUse this command to set COS for VOICE packet.

Command Syntax

voice vlan set phb to(af11|af12|af13|af21|af22|af23|af31|af32|af33|af41|af42|af43|ef|df|cs1|cs2|cs3|cs4|cs5|cs6|cs7)

no voice vlan set phb

69

af11 Assured forwarding class 1, low drop precedence, PHB of (priority 2, colorgreen)

af12 Assured forwarding class 1, medium drop precedence, PHB of (priority 2,color yellow)

af13 Assured forwarding class 1, high drop precedence, PHB of (priority 2, colorred)










ef Expedited forwarding, PHB of (priority 12, color green)

df Default forwarding, PHB of (priority 1, color green)

cs1 Class selector 1, PHB of (priority 0, color green)







70

Command Mode


Default

By default the phb is ef

Usage

This command is used to set COS for VOICE packet in global configuration.

Examples

This example shows how to set phb to df:

Switch(config)# voice vlan set phb to df

Related Commands


5.4 voice vlan mac-addressUse this command to add OUI to system.

Command Syntax

voice vlan mac-addressMAC MASK description LINE

no voice vlan mac-addressMAC

MAC Source MAC address (unicast or multicast) to add to the address table

MASK The MASK for the Source MAC

LINE The description for this OUI

Command Mode


71

Default

There are 5 default OUI in the system.:

0003-6b00-0000 Cisco phone

000f-e200-0000 H3CAolynk phone

00d0-1e00-0000 Pingtel phone

00e0-7500-0000 Polycom phone

00e0-bb00-0000 3Com phone

Usage

This command is used to add OUI to system database. The packet will be consider as VOICEC packetwhen the sourec MAC match the OUI.

Examples

This example shows how to add OUI to system:

Switch(config)# voice vlan mac-address 0034.3400.0000 FFFF.FF00.0000 description test

Related Commands


5.5 voice vlan enableUse this command to enable VOICE VLAN on port.

Command Syntax

voice vlan enable

no voice vlan enable

Command Mode


Default

VOICE VLAN is disable on port

72

Usage

This command is used to enable VOICE VLAN on port.

Examples

This example shows how to enable VOICE VLAN on port:

Switch(config-if)# voice vlan enable

Related Commands


5.6 show voice vlan stateUse this command to show the current status of VOICEC VLAN.

Command Syntax


Command Mode

Privileged EXEC

Default

None

Usage

This command is used to show the current status of VOICEC VLAN.

Examples

This example shows how to show the current status of VOICEC VLAN:

Switch# show voice vlan state

Related Commands

None

73

5.7 debug voice-vlanUse this command to show the current status of VOICEC VLAN.

Command Syntax

debug voice-vlan (all | events)

no debug voice-vlan (all | events)

all Debug all VOICEC VLAN info

events Debug VOICEC VLAN event info

Command Mode

Privileged EXEC

Default

None

Usage

This command is used to debug VOICEC VLAN

Examples

This example shows how to debug VOICE VLAN

Switch# debug voice-vlan all

Relate

Documents

S5800 Series Ethernet CLI | FS · 2017. 10. 26. · 11Layer2ProtocolsTunnelingCommands.....167 11.1l2protocolenable.....167