Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
1
1 5
2 6
3 7
4
2
3
4
5
6
7
Fast. Easy. Setup!RP-AC66 Quick Start Guide
2Connect via WPS1Power on 3Find the best
spotFor setup, plug the RP-AC66 into a power outlet within 6 feet of your router/AP.
The LEDs should start blinking once the RP-AC66 is plugged in. Wait up to 1 minute for the power LED to turn solid green.
The Wi-Fi LED indicates signal strength to/from the router/AP for both 2.4 and 5 GHz bands.
On your router/AP, press and hold the WPS button for at least 3 seconds.
Quickly go to the RP-AC66 and press and hold the WPS button for at least 3 seconds. When the connection is made, the LEDs will change from blinking to solid.
To use both 2.4 and 5 GHz bands, connect to Wi-Fi network: ASUS_RPAC66, then go to http://repeater.asus.com to access advanced settings. Use admin as both username and password.
Move and plug in the RP-AC66 to the farthest place where signal strength is excellent or good according to the Wi-Fi performance LEDs.
If the LED indicates poor signal, move the RP-AC66 closer to the router/AP.
When configured via WPS, either the 2.4 or 5 GHz Wi-Fi LEDs will be lit. Devices can still connect using both bands.
NOTE
NOTE
IP: 192.168.1.1
Excellent
Good
Poor
No connection none
Red
Orange
Green
2.4 GHz / 5 GHz Color Performance
Wi-Fi network name: ASUS_RPAC66
Position within 6 feet.
LED
Router/AP
Power LED WPS button
5GHz LED Reset button
2.4GHz LED
Gigabit RJ-45 port
Power On/Off switch
Best performance
Poor performance
Login information
Wi-Fi performance LEDsSignal strength between the router/AP and RP-AC66
Factory Default Setting
Your RP-AC66 is now set up!
RP-AC66 Wi-Fi network name
Existing router network name_RPT
RP-AC66 Wi-Fi password
Existing router network password
Your network info should be:
WPS
WPS
1
1 5
2 6
3 7
4
2
3
4
5
6
7
RP-AC66 Guía de inicio rápido
2Conexión a través de WPS1Alimentación
conectada 3Encuentre el mejor lugar
Para realizar la instalación, enchufe el RP-AC66 a una toma de corriente eléctrica a una distancia de 2 metros (6 pies) del router o PA.
Los LED deben comenzar a parpadear cuando su RP-AC66 se enchufe. Espere 1 minuto hasta que el LED de alimentación se ilumine en verde permanentemente.
El LED Wi-Fi indica la intensidad de la señal hacia el enrutador o punto de acceso o desde estos, tanto para la banda de 2,4 GHz como para la de 5 GHz.
Mantenga pulsado el botón WPS de su router o PA durante, al menos, 3 segundos.
Vaya rápidamente a su RP-AC66 y presione sin soltar el botón WPS durante al menos 3 segundos. Cuando la conexión se haya realizado, los LED dejarán de parpadear y se iluminarán permanentemente.
Para utilizar tanto la banda de 2,4 GHz como la de 5 GHz, conéctese a la red Wi-Fi ASUS_RPAC66 y , a continuación, vaya a http://repeater.asus.com para acceder a la configuración avanzada. Utilice admin tanto para el nombre de usuario como para la contraseña.
Mueva y enchufe su RP-AC66 al lugar más alejado donde la intensidad de la señal sea excelente o buena según los LED de rendimiento Wi-Fi.
Si el LED indica una señal débil, acerque su RP-AC66 al enrutador o punto de acceso.
Cuando se configure a través de WPS, el LED Wi-Fi 2,4 o 5 GHz se iluminará. Los dispositivos podrán seguir conectándose utilizando ambas bandas.
NOTA NOTA
IP: 192.168.1.1
Excelente
Bueno
Deficiente
Sin conexión Ninguno
Rojo
Naranja
Verde
Color para 2,4 GHz / 5 GHz
Rendimiento
Nombre de red Wi-Fi: ASUS_RPAC66
Posición dentro de una distancia de 2 metros (6 pies).
LED
router/PA
LED de encendido y apagado
Botón WPS
LED de 5 GHz Botón Restablecer
LED de 2,4 GHz
Puerto RJ-45 Gigabit
Conmutador de encendido y apagado
El mejor rendimiento
Rendimiento bajo
Información de inicio de sesión
Rendimiento del LED Wi-FiIntensidad de señal entre el enrutador o punto de acceso y RP-AC66
Configuración predeterminada de fábrica
¡Su RP-AC66 estará ahora instalado!
Nombre de red del RP-AC66 Wi-Fi
Nombre_RPT de red del router existente
Contraseña del RP-AC66 Wi-Fi
Contraseña de red del router existente
Su información de red debería ser:
WPS
WPS