Upload
andrei-gheorghica
View
216
Download
0
Embed Size (px)
Citation preview
8/13/2019 Rothoblaas.vaporvlies 85.Technical Data Sheets.en
1/2
Technical datasheet
Revision 23/04/2013Note: We reserve the right to change product features at any time and without notice.
Vaporvlies 85
code DZ500008 Vaporvlies 85
Synthetic 2-layer vapour barrier membrane for direct application on hot side of heat insulation.
Particularly suitable for laying on walls
Technical datasheet:
Specifications StandardUnit of
measurementValue Tolerance
Mass per unit area EN 13859-1 g/m 100 -10 +10
Thickness - mm 0.4 - -
Sd vapour transmission properties EN 1931 m 25 -8 +8
Tensile strength MD/CD EN 12311-1 N/50mm 150/130 - -
Elongation MD/CD EN 12311-1 % 50/50 - -
Nail tear resistance MD/CD EN 12310-1 N 80/80 - -
Resistance to water penetration EN 1928 - pass
UV resistance - months nd - -
Flexibility at low temperature EN 1109 C -20
Working temperature - C -20/+80 - -
Fire reaction EN 13501-1 - E - -
Airtightness EN 13859-2 m3/m2h 50Pa < 0,02 - -
Joint strength EN 12317-2 N/50mm nd - -
Impact resistance EN 12691 mm nd - -
Material properties after artificial aging test
Resistance to water vapor passage EN 1296 - pass - -
Alkali resistance EN 13984 - pass - -
MD:longitudinal CD: transversal
EN 13984 Flexible membranes for waterproofing - Plastic and rubber vapour control layers -Definitions and characteristics
This product does not contain hazardous substances12
Supplied: Composition:Roll height 1.5 m Upper layer Non-woven polypropylene fabricRoll length 100 m Substrate Polypropylene vapour check filmRoll surface area 150 mRoll weight 13 kgRolls per pallet 50Pallet size 1.5 x1.2 x1.2 m
8/13/2019 Rothoblaas.vaporvlies 85.Technical Data Sheets.en
2/2
Technical datasheet
Revision 23/04/2013Note: We reserve the right to change product features at any time and without notice.
FIELD OF USE
VAPORVLIES 85
LAYING INDICATIONSThe VAPORVLIES 85 vapour check membrane is placed parallel to the platform beam for application on roofs or to
the floor for application on walls. The second layer must be overlapped at least 15 centimetres over the first layer.Each layer must be fixed to the support with a mechanical fastening device (i.e. hammer tacker HH735347). Thetransparency of the fabric allows for clear viewing of the underlying substrate on which fastening will be performed.The fabric must be applied on the hot side of the roof or wall. We also recommend overlapping the fabric by at least30 centimetres in the butt joints.Use SEAL BAND (DZ100125/127) sealing band or FLEXI BAND (DZ100110/120) with rough surfaces (like raw OSB) forfurther air or water sealing.
PRODUCT STORAGE AND CARE
Keep the rolls in a dry place, away from heat and direct sunlight. It is also advisable to avoid overlapping of pallets.These actions are necessary to preserve the original features of the product.
NB:For the application of all Rothoblaas products, we recommend reading the installation instructions provided in
our catalogue and downloading available technical datasheets from our websitewww.rothoblaas.com.
http://www.rothoblaas.com/http://www.rothoblaas.com/http://www.rothoblaas.com/http://www.rothoblaas.com/