Embed Size (px)
Citation preview
PAGE 1
12345
REMARKSMM/DD/YYRolling Workbench - Festool Additions
Moxon Vise and Router Table
April 8th 2014
PAGE 1
12345
REMARKSMM/DD/YYRolling Workbench - Festool Additions
Moxon Vise and Router Table
April 08th 2014
4"
49" 12"
19"
49"
23-1
/2"
1/2"
29-1/4"
Please see Page 2 for top adjustment and gap
4"
4"
2 3/8" x 1/2" x 25" strips (attach drawer slides)
Additional 3/4" strip this location only
3/4 " hardwood slides for chip catcher drawer
12-1/4"
Note: Construct 4" pads accordingly to match your choice of casters.
ALL 3/4" plywood construction unless noted.
6-1/4"
29-7/8"
22-5
/8"
..._ _ /_ _ /_ _
..._ _ /_ _ /_ _
..._ _ /_ _ /_ _
..._ _ /_ _ /_ __ _ /_ _ /_ _ ... 00
1A
PAGE 2
12345
REMARKSMM/DD/YY
1/8" Vertical adjustment gap1/8" Vertical adjustment gap
Rolling Workbench - Festool AdditionsMoxon Vise and Router Table
April 08th 2014
1/2" x 1 5/8"
3/4" top overhangs sides by 1/8"
Router opening is roughly centered. Cut accordingly for your router plate and
allow for T/Miter slot if used.
1/8" Vertical adjustment gap (both sides)
Slotted holes 3x each side
The router top is designed with slight adjustment so it can be adjusted to plane perfectly with the Festool MFT (1080 version in this case).
There are three slots on each side that can be accessed from router door and by removing the top front storage drawer. Attach with pan head screws or fasteners of your choice.
Notch both sides
PAGE DESCRIPTION
..._ _ /_ _ /_ _
..._ _ /_ _ /_ _
..._ _ /_ _ /_ _
..._ _ /_ _ /_ __ _ /_ _ /_ _ ... 00
1A
PAGE 3
12345
REMARKSMM/DD/YYRolling Workbench - Festool Additions
Moxon Vise and Router Table
April 08th 2014
4" 4"
31-1/2"
Left View
Note: Construct 4" pads accordingly to match your choice of casters.
22"
..._ _ /_ _ /_ _
..._ _ /_ _ /_ _
..._ _ /_ _ /_ _
..._ _ /_ _ /_ __ _ /_ _ /_ _ ... 00
1A
PAGE 4
12345
REMARKSMM/DD/YYRolling Workbench - Festool Additions
Moxon Vise and Router Table
April 08th 2014
Right View
Router door opening and size is not critical. You can have a face mounted door if you like. This design has a cleaner flush mount door (not shown here) which serves no special purpose.
16-1/2"
12-1
/2"
15"
Filler piece
8-1/4"
PAGE DESCRIPTION
..._ _ /_ _ /_ _
..._ _ /_ _ /_ _
..._ _ /_ _ /_ _
..._ _ /_ _ /_ __ _ /_ _ /_ _ ... 00
1A
PAGE 5
12345
REMARKSMM/DD/YY
Right View - Side removed for clarity
Rolling Workbench - Festool AdditionsMoxon Vise and Router Table
April 08th 2014
Router door opening and size is not critical. You can have a face mounted door if you like. This design has a cleaner flush mount door which serves no special purpose.
6-1/
4"
6"
Hardwood slides
Filler
15-3/8"
26"
Router clippings chute(non critical dimension)
22-5
/8"
1/2" plywood
PAGE DESCRIPTION
..._ _ /_ _ /_ _
..._ _ /_ _ /_ _
..._ _ /_ _ /_ _
..._ _ /_ _ /_ __ _ /_ _ /_ _ ... 00
1A
PAGE 6
12345
REMARKSMM/DD/YYRolling Workbench - Festool Additions
Moxon Vise and Router Table
April 08th 2014
3"1-
1/4"
1-3/4"1-3/8" 2-1/2" 1-3/8"
1/8 " reveal to side panel
1/8" reveal toside panel
Flush with top of plywood
Flush with top
Trim
Centered on vertical plywood
9-1/2"
1-1/
2"
1-3/8"
Actual trim to be based on your finished cabinet size. Top edges of horizontal trim need to be flush with top surfaces. Outside verticals have 1/8" reveal to sides. The 2 1/2" vertical piece has a 1 1/4" reveal on left and 1/2" on right.
GLUE AND NAIL for rigidity
PAGE DESCRIPTION
..._ _ /_ _ /_ _
..._ _ /_ _ /_ _
..._ _ /_ _ /_ _
..._ _ /_ _ /_ __ _ /_ _ /_ _ ... 00
1A
PAGE 7
12345
REMARKSMM/DD/YYRolling Workbench - Festool Additions
Moxon Vise and Router Table
April 08th 2014
Slide bottoms
26 1/2" wide by 29" deep (approx)
16 1/2" wide by 25"deep (approx)
Dimensions for reference only. Build slides to width after cabinet is built and drawer slides installed.
Glue fronts and Kreg screwfrom bottom
PAGE DESCRIPTION
..._ _ /_ _ /_ _
..._ _ /_ _ /_ _
..._ _ /_ _ /_ _
..._ _ /_ _ /_ __ _ /_ _ /_ _ ... 00
1A
PAGE 8
12345
REMARKSMM/DD/YYRolling Workbench - Festool Additions
Moxon Vise and Router Table
April 08th 2014
Slide Fronts
Dimensions for reference only. Build fronts based on your actual dimensions.
27-5/8"
5-1/
4"16-3/4"
9"
2"
1/2" Plywood
5-1/
4"
PAGE DESCRIPTION
..._ _ /_ _ /_ _
..._ _ /_ _ /_ _
..._ _ /_ _ /_ _
..._ _ /_ _ /_ __ _ /_ _ /_ _ ... 00
1A
PAGE 9
12345
REMARKSMM/DD/YYRolling Workbench - Festool Additions
Moxon Vise and Router Table
April 08th 2014
Drawers are about8" square. I ended
up using three drawers instead of
four. Size your drawers accordingly
As a final step add trim over top of drawer/box to divert clippings into box
PAGE DESCRIPTION
..._ _ /_ _ /_ _
..._ _ /_ _ /_ _
..._ _ /_ _ /_ _
..._ _ /_ _ /_ __ _ /_ _ /_ _ ... 00
1A
