Upload
quykiem02
View
244
Download
1
Embed Size (px)
Citation preview
8/3/2019 RNO Presentation
http://slidepdf.com/reader/full/rno-presentation 1/12
RNO Presentation
INDEX
1- About RNO
2- MRR
3- NCS & NOX
4- FAS & FOX
5- TET
-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.
RNO (Radio Network Optimization):
RNO is very useful tool to:
1- Collect measurement data about all calls for uplink and down link in the
selected cells during specific time
2- Analyze the reports based on the measurement data and gives
recommendations on how to configure the GSM network
3- Implements those changes with or without user interaction
All of those can be achieved by five simple programs:
1- MRR: Measurement Result Report.
2- NCS: Neighboring Cells Support.
3- NOX: Neighboring cells Optimization eXpert.4- FAS: Frequency Allocation Support.
5- FOX: Frequency Optimization eXpert
6- TET: Traffic Estimation Tool.
-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.--.-.-.-.-.-.-.-
MRR (Measurement Result Report)
MRR is used to collect the measurement data of both uplink and down link of all the
calls of MSs located in specific cells by monitoring:
1- RXQual UL
2-
RXQual DL3- RXLevel UL
4- RXLevel DL
5- Timing Advance (TA)
6- Path Loss UL
7- Path Loss DL
8- Power Rediated from BTS
9- Power of MS
1
8/3/2019 RNO Presentation
http://slidepdf.com/reader/full/rno-presentation 2/12
MRR Main Window
MRR Can be used for
1- Find out the cells with Bad Quality
Example:
This is accumulating Histogram showing the percentage of samples for
RXQual DL. And for this example we can see that the 25% of samples have Bad
quality (>5), which is not acceptable rate.
2
8/3/2019 RNO Presentation
http://slidepdf.com/reader/full/rno-presentation 3/12
This is a similar Histogram about the Up Link Quality, which gives us the ability to
specify the cells, which need optimization or drive test.
This a histogram of TA through which we can find the unnatural coverage distribution
of the cell
3
8/3/2019 RNO Presentation
http://slidepdf.com/reader/full/rno-presentation 4/12
The last chart is the RXLevel Histogram which give us Over View for the level in the
rea if it's acceptable or not.
rk and discover the unnatural behavior of the cells
2- Monitoring the New added Sitemplementation of a new feature to
e cells and follow up the customer
5- some optimization to a specific cells and
6- e cells that are shooting too far
8- ion
a
MRR can be very useful for this Implementation:
1- Monitoring the Netwo
3- Making a comparison before and after the i
the Network Like HR for example
4- Find out the trouble shooting of th
complains
Find out the effect of implementing
monitor their behavior before and after the optimization
Discover th
7- Discover the unbalanced power budget for some cells
Discover the cells which need or don't need power reduct
-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.
4
8/3/2019 RNO Presentation
http://slidepdf.com/reader/full/rno-presentation 5/12
NCS (Neighboring Cells Support)
sed to analyze the Neighboring cell relation by measuring the BCCH signalNCS is u
strength level.
Examples:
This Chart gives us good idea about the existing and missing neighbors.nd by going back to the NCS cell report we can find the Name of the missing
ength is
A
Neighbor and an idea about how many times the new frequency signal str
stronger than the serving cell.
And this idea is clear in the next chart:
5
8/3/2019 RNO Presentation
http://slidepdf.com/reader/full/rno-presentation 6/12
NOX is a tool, which is built on the data collected by NCS to give us the suggestions
for adding missing neighbors and removing unnecessary neighbors
1-ADD Neighbors
6
8/3/2019 RNO Presentation
http://slidepdf.com/reader/full/rno-presentation 7/12
2- Remove Neighbors
NCS is very useful for:
1- Find out the missing neighbors
2- Have an idea about the traffic relief from the serving cell to this new neighbor
NOX is useful for giving us over view on the missing and adding neighbors, and
allow us to applying the suggestions of NCS and NOX automatically on the Network
Or by schedule-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.
FAS (Frequency Allocation Support):
FAS is used to measure the uplink interference and estimate the down link by using
BA list for generate ICDM (Interference Cell Dependency Matrix):
Interference is measured in the idle mode for one time slot so there is no problem for
SFH or BBH
7
8/3/2019 RNO Presentation
http://slidepdf.com/reader/full/rno-presentation 8/12
FAS main window
Examples:
FAS cell report is a powerful report gives you all measurements about the interference
existed on the uplink for all the frequencies on the studied cell, and it suggests new
frequencies with low interference on the uplink.
8
8/3/2019 RNO Presentation
http://slidepdf.com/reader/full/rno-presentation 9/12
Through FAS cell report chart, the results can be clearly to observe.
FAS ICDM report:
FAS-ICDM calculates the Co & Adj interference between two cells if they have Co &
Adj frequency, and these calculations are done irrespective of the frequency plan
FAS can be very useful for various implementations:
1- Discover interfered frequencies on cells
2- Find replacement frequency for interfered cells
3- Discover swap sectors from FAS-ICDM
4- Build Interference Matrix for Planning tools like TCP
5- Find new frequencies for new TRUs
6- Find the worst frequency to eliminate when removing TRUs
7- Frequency plan for new sites8- Optimize the frequency plan
9
8/3/2019 RNO Presentation
http://slidepdf.com/reader/full/rno-presentation 10/12
FOX (Frequency Optimization eXpert)
FOX recording is executed both on the UL and DL in the same way as a FAS
recording, the use of FOX adds on help for analyzing the result and improving thenetwork manually or automatically.
In recommendation mode, FOX suggestion reallocations of frequencies and the user
can accept reject or change the suggestions before the reallocation is executed in the
network.
When running a FOX recording in automatic mode the reallocation is implement
Automatically.
10
8/3/2019 RNO Presentation
http://slidepdf.com/reader/full/rno-presentation 11/12
Planning area
Planning Areas are a way for determine all the changes we need for optimizing the
network regarding changes in neighboring relations or Frequency reallocations and
can be easily implemented to the network by CNA (Cellular Network Administration)
-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.
TET (Traffic Estimation Tool):
By using the TET and TEMS transmitter we can test the frequency, which apply on
the transmitter.
Test frequency is added to the BA-lest of the surrounded cells (which is included in
the cell set)_this is done by TET_, and after that we can see from theTET the relief
load from the surrounded cells, which occurred, by the transmitter.
So by this tool we can test the better frequency to use, antenna type and height, thelocation of the site (Micro or Macro), and the transmitter output power
11
8/3/2019 RNO Presentation
http://slidepdf.com/reader/full/rno-presentation 12/12
Note: the BCCH can’t be changed when the record has been scheduled.
TET overview report:
TET traffic level chart: for the selected cell from the TET overview report
12