RM Biltrite Sheet Rubber Catalogue 2018bostonfloormats.com/sites/default/files/RM Biltrite Sheet...experienced compounders. We recommend self-testing polymers as we cannot guarantee

THERMOPLASTICS

®

®RUBBER

Product Catalog

USA

Phone: 800.877.8775 • Fax: 888.894.0204

Email: [email protected] • Web: www.rmbiltrite.com

Europe

Phone: +31 (0)548 659065 • Email: [email protected]

Web: www.rmbiltrite.eu

Corporate Office: 8525 Dunwoody Pl • Sandy Springs, GA 30350

Midwest Office & Distribution Center: 1600 Downs Dr. Unit 4 • West Chicago, IL 60185

European Office: Windmolen 22, 7609 NN Almelo, The Netherlands

USA Manufacturing: 31 Highland St. • Chelsea, MA 02150

27

Standard Terms and Conditions of SaleRM BILTRITE™ LLC sells products commercially for multiple applications determined by the Buyer or end-user. Determination of the suitability of the products for the uses and applications of Buyers and end-users shall be the sole responsibility of the Buyer or end-user. Consultation with qualified engineers and testing laboratories is recommended. RM BILTRITE™ LLC does not recommend any of its products for any particular use or application. The purchaser or end-user shall assume full responsibility for the adequacy and suitability for the intended use. Rubber products may fail as a result of temperature variances, excessive pressures, abrasion or damaging substances. The wear life of rubber products is limited by the circumstances and conditions of use. Buyer and end-users should regularly inspect the rubber to determine if it should be replaced for operational and safety requirements, to prevent injury of damage to persons and property.

Payment Terms: Net 30 days from date of invoice on approved credit and accounts in current good standing. At our discretion, we may require full or partial payment in ad-vance if Buyer does not qualify for terms or continued terms. A charge of 1.5% per month (or at the highest rate permitted by law) shall be charged on overdue accounts. Credit balances will only be applied to future purchases.

Transportation Policy: All shipments are made FOB Origin, Freight Collect or FOB Origin, Freight Prepaid & Add. Seller will determine the point of shipment, the method of transportation, and the routing of shipment. For Freight Prepaid & Add shipments, Seller reserves the right to determine the most economical shipping method on shipments, and all freight charges shall be added to Buyer invoice. Partial deliveries shall be accepted by the Buyer. Seller does not guarantee any delivery or completion date. Seller shall not be liable or responsible for any loss, damage, expense or charge of any kind, direct or indirect, suffered or incurred by Buyer as a result of such delay. All shipments shall be carefully inspected when received and any claims for freight damage should be noted on the Bill of Lading. Seller shall not be responsible for freight damage and/or concealed damage not reported to the carrier at time of delivery.

Prices/Minimum Order: Minimum order is $500.00. All prices are subject to change without prior notice. All Buyer purchase orders shall be accepted by Seller at time of order. All price pages and catalog weights are approximate and actual shipping weights may vary from these listings. In case of dispute, actual shipping weight will apply. All orders accepted by the Seller are accepted on the understanding that Buyer, by placing the order, has agreed to these Standard Terms and Conditions of Sale, and are part of the Buyer’s order.

Quantity Variance: Due to manufacturing variances, the quantity of goods delivered can be within 10% more or less, of the quantity specified and shall be charged at the unit price. Buyer agrees to accept quantity variances that may differ from the purchase order as described within.

Cancellations: Requests for cancellation or modification for orders from warehouse stock must be submitted in writing and received by Seller at least 2 days prior to shipment. No cancellations or modifications are allowed on direct container shipments. Orders for merchandise produced and/or shipped specifically for a customer cannot be canceled once goods are produced.

Returned Goods: No goods may be returned without Seller’s prior written authorization. Each request for exchange or return shall describe the condition of the goods, and the reasons for the requested return or exchange. Buyer shall request and receive a RMA (Return Merchandise Authorization) number from the Seller before returning any goods. Seller will not accept any returned good shipment without a RMA number attached to the shipment. For return of 1st class goods, Buyer shall pay return transportation costs and a restocking charge of 15%. All return requests shall apply only to warehouse stock products purchased within a six month period. No returns on goods that have been cut, treated, altered, processed, subject to abuse or misuse, or damaged after shipment by Seller. No returns on special orders, made-to-order goods, or custom-cut lengths.

Warranties and Disclaimers: Goods furnished under this agreement shall conform to the description herein. All first quality goods are warranted to be free from defects in material and workmanship at the time of shipment. Seller shall convey good title to buyer. Seller further warrants that the goods sold hereunder do not infringe any valid US patent, and Seller does not warrant, however, that the use of the good or products made therefrom, either alone or in conjunction with other materials, will not infringe any valid US patent. THE WARRANTIES SET FORTH IN THIS PROVISION ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, INCLUDING WARRANTIES ARISING FROM COURSE FOR DEALING OR USAGE OF TRADE. SELLER MAKES NO WARRANTY, EXPRESSED OR IMPLIED, OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. ALL PRODUCTS ARE SOLD AND WARRANTED ONLY PURSUANT TO OUR PUBLISHED TERMS AND CONDITIONS OF SALES. WE ARE NOT RESPONSIBLE FOR THE USER FOR ANY CONSEQUENTIAL, INCIDENTAL, OR SPECIAL DAMAGES RESULTING FROM PRODUCT USE OR PROCESSING. IN NO CIRCUMSTANC-ES WILL SELLER’S LIABILITY EXCEED THE PURCHASE PRICE OF THE GOODS.

Products Suitability and Length of Use: Buyer acknowledges the use of its own knowledge, expertise, skill, experience and judgment in the selection of products(s) and /or in the selection, provision, or designation of any specifications or set of specifications for a product(s) agreed upon by the Buyer and Seller. Buyer acknowledges that Seller shall not be liable for, and Buyer assumes all risk of, inaccurate or unsuitable specifications or information provided, selected or designed by the Buyer. RM BILTRITE™ LLC MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE SUITABILITY OF MATERIALS FOR A PARTICULAR PURPOSE. BUYERS AND USERS MUST DETERMINE THE SAFETY AND SUITABILITY OF RM BILTRITE™ LLC’S PRODUCTS FOR THEIR OWN PURPOSES, AND ASSUME ALL RISK, RESPONSIBILITY, AND LIABILITY FOR ALL INJURIES, LOSSES, OR DAMAGES ARISING FROM THE APPLICATION OF THE INFORMATION OR USE OF RM BILTRITE™ LLC’S PRODUCTS, WHETHER OR NOT CAUSED BY RM BILTRITE™ LLC’S NEGLIGENCE OR BASED ON STRICT PRODUCT LIABILITY.

Physical Properties Grade 1: ASTM basic requirements for physical properties are based on values obtained from standard laboratory test specimens prepared and tested in accordance with the applicable ASTM test methods. Test results from specimens prepared from finished products may not duplicate values obtained from standard test specimens. Per ASTM D2000, Section 7.1, Buyer agrees that when standard test specimens are cut from finished parts in accordance with Practice D3183, a deviation of the up to 10% on tensile strength and elongation values is permissible.

Claim Period and Remedies: Prompt written notice shall be given to Seller of any claim or failure of goods to conform to the warranties hereunder. Should any failure to conform to these warranties appear under normal and proper use within the period of six (6) months from the date of shipment to the Buyer, Seller shall correct such noncon-formity, at its option, by repair or replacement of the defective goods or by the refund of the purchase price thereof with due allowances made for the service rendered by the goods returned. In no circumstances shall Buyer commence any action under this Agreement later than one year after receipt of the goods. The remedies provided above are the Buyer’s sole remedies for any failure of Seller to comply with its obligations.

Limitation of Liability: Seller shall not be liable to contract, in tort (including negligence) or otherwise for damage or loss other property, loss of profits or revenue, loss of use of property or equipment, claims of customers of the Buyer, or for any special, indirect , incidental, or consequential damages whatsoever. Under no circumstances shall Seller’s liability exceed the purchase price of the goods in respect of which damages are claimed.

Attorney’s Fees and Venue: In any action to collect amounts due Seller, with respect to sales made to Buyer, arising out of or relating to this Agreement or any such sales, or in which a party seeks an interpretation of this Agreement or asserts it as a defense, the prevailing party shall be entitled to recover attorney’s fees in any amount determined by the Court to be reasonable, as well as such party’s costs of suit. All notices, requests, claims and other communication by Buyer with respect to this Agreement or sales hereunder shall be direct to Seller at its corporate offices located at 8525 Dunwoody Pl, Sandy Springs, GA 30350. Any action brought by Buyer against Seller must be brought in a State or Federal Court located in Fulton County, Georgia, and any action brought in any other locations shall, upon appropriate motion by Seller, be dismissed.

Entire Agreement: This agreement constitutes the complete and final Agreement of sale and purchase of the products specified herein and supersedes all prior contracts and discussions. NO modification hereof shall be effected by the use of purchase order, acknowledgment, acceptance, or other forms that vary with or are additions to the terms and conditions contained herein. No modification shall be effected in any manner other than in writing and signed by seller.

Governing Law: This contract shall be governed by and construed under the laws of the State of Georgia, USA.

RM BILTRITE™ TERMS & CONDITIONS

2

Warehouse Locations

Mira Loma, CA

Denver, CO

North Haven, CT

Orlando, FL

Atlanta, GA

West Chicago, IL

La Grange, KY

Chelsea, MA

Billings, MT

Milwaukee, WIMira Loma, CA Denver, CO

North Haven, CT Orlando, FL

Atlanta, GA West Chicago, IL

La Grange, KYChelsea, MA

Billings, MTMilwaukee, WI

RM Biltrite™ is a Sandy Springs, Georgia based company specializing in the manufacture and distribution of rubber sheeting, matting, flooring, thermoplastics, and a wide variety of industrial rubber products. Our offices are located in the USA, Netherlands, China, India, and Thailand, while our thermoplastics manufacturing facility is located in Chelsea, Massachusetts.

RM Biltrite™ has over 185 years of combined experience with the design, development, and contract manufacturing of a large assortment of rubber and plastic products. Our customers include gasket cutters, distributors, industrial supply retailers and wholesalers servicing the automotive, trucking, mining, chemical, construction, OEM, flooring, roofing, electrical safety and agricultural industries.

Since its establishment in 1986 by the current management, RM Biltrite™ has achieved success through our highly exceptional customer assistance & support. Quality products, competitive pricing, and excellent service are just the beginning of what we offer in our relationship with customers. The strength of our company is our committed team of employees and their dedication to our customers' satisfaction. RM Biltrite™ maintains nine distribution centers within the United States, along with a European distribution center in the Netherlands.

Please visit www.rmbiltrite.com or call 800.877.8775 for more information.

TABLE OF CONTENTS

›› Introduction 2

›› Sheet Rubber • Neoprene 4 • Nitrile (Buna-N) 5 • Natural Rubber (NR) 6 • EPDM 6 • SBR 7 • CSM (Hypalon®) 7 • Cloth-Inserted (CI): SBR & Neoprene 8 • Diaphragm 9 • Silicone 10 • Fluoroelastomer (FKM, Viton®) 11 • Butyl 12 • Masticated Rubber 13

›› Rubber Matting • Corrugated 14 • Nu-Grip® 14 • Gemstone 15 • Pebble 15 • Diamond 15 • Switchboard 16

›› Rubber Flooring • Durafloor® 17 • Dura-Tranz® 18

›› Thermoplastics • Vinyl Matting 19 • Switchboard Matting 20 • Military Electrical Grade (MEG) Switchboard Matting 21 • Electrostatic Discharge (ESD) Matting 22 • Conductive Matting 22 • TPO Walkway 23 • PVC Walkway 24 • Acoustical (MLV) Barrier 25 • Commercial Kitchen Flooring 25

›› Material Information • Rubber Manufacturing Tolerances 26 • Rubber Operating Temperatures 26 • Polymer Selection Criteria 26

›› Terms & Conditions 27

326

MATERIAL INFORMATION

Note: Width tolerance ± 1", length tolerance ± 10%. Material made by the coating process is subject to considerably more restrictive tolerances: under 0.031” (0.79 mm), ± 0.003” (± 0.08 mm); 0.031” (0.79 mm) and over, ± 10%. Thermoplastic tolerances are product specific and available upon request.

Rubber Manufacturing TolerancesNOMINAL THICKNESS TOLERANCES ±

Fraction (Inches) Decimals (Inches) Millimeters Inches Millimeters

Under 1/32 Under 0.031 Under 0.79 0.010 0.251/32 to but not including under 1/16 0.031 to 0.062 0.79 to 1.59 0.012 0.31/16 to but not including under 1/8 0.062 to 0.125 1.59 to 3.18 0.016 0.41/8 to but not including under 3/16 0.125 to 0.187 3.18 to 4.8 0.020 0.513/16 to but not including under 3/8 0.187 to 0.375 4.8 to 9.5 0.031 0.793/8 to but not including under 9/16 0.375 to 0.562 9.5 to 14.3 0.047 1.199/16 to but not including under 3/4 0.562 to 0.750 14.3 to 19.2 0.062 1.59

3/4 to but not including under 1 0.750 to 1.000 19.2 to 25.4 0.094 2.381 and over 1.000 and over 25.4 10% 10%

This resistance chart is based on a single polymer compound and is offered as a general guide, including the suitability of various elastomers for service in these chemicals and fluids. The ratings are mainly based on published literature of various polymer suppliers, rubber manufacturers, and in some cases, the opinion of experienced compounders. We recommend self-testing polymers as we cannot guarantee the accuracy of this chart nor assume responsibility for use thereof. Many factors must be considered in using a rubber part in service. The most important as we see them are:1) The temperature of service: Higher temperatures increase the affect of all chemicals on polymers. The increase varies with the polymer and the chemical. A compound quite suitable at room temperature might fail at elevated temperatures.2) Conditions of service: A compound that swells badly might still function as a static seal yet fail in any dynamic application.3) The grade of the polymer: Many types of polymers are available in different grades that vary greatly in chemical resistance.4) The compound itself: Compounds designed for their outstanding properties may be poorer in performance in a chemical than one designed especially for fluid resistance.5) The durometer: In general, the harder the compound the better the resistance.

Polymer Selection CriteriaAPPLICATION NR/SBR Neoprene Nitrile EPDM Butyl Hypalon® Silicone Viton®

Petrol Poor Poor Good Poor Poor Poor Poor Excellent

Lubricating Oils Poor Fair Good Poor Poor Fair Good Excellent

Acids Fair Fair Good Excellent Excellent Excellent Fair Good

Alkalis Fair Fair Fair Good Excellent Excellent Fair Fair

Hydraulic Phosphates Poor Poor Poor Good Good Fair Good Poor

Fluid Silicates Poor Good Good Fair Fair Good Poor Good

Abrasion Resistance Excellent Good Good Good Good Good Fair Good

Tear Strength Good Good Good Fair Good Fair Poor Fair

Impact Resistance Excellent Good Fair Good God Good Fair Fair

Resilience Excellent Good Good Good Fair Good Poor Fair

Impermeability to Gases Fair Good Good Good Excellent Excellent Poor Excellent

Compression Set Good Good Good Fair Fair Fair Good Good

Rubber Operating TemperaturesTemp °F

Viton®SiliconeHypalon®ButylEPDMNitrileNeopreneNatural Rubber

Temp °C

572° 527° 482° 437° 392° 347° 302° 257° 212° 167° 122° 77° 32°-13°-58°-103°

Maximum/Minimum

Continuous

300° 275° 250° 225° 200° 175° 150° 125° 100°

75° 50° 25°

0°-25°-50°-75°

25

FLEXGARD® NEOPRENE

4

Typical Physical Properties: Per ASTM D300, Section 7.1, Buyer agrees that when standard test specimens are cut from finished parts in accordance with Practice D3183, a deviation to the extent of 10% on tensile strength and elongation values is permissible. All of our thermoplastic products are a proprietary blend of plastics and other components. In any application, the customer should evaluate the performance requirements and conditions that will affect the working life of the thermoplastic product. Where appropriate, field tests may need to be performed before the type of thermoplastic is selected. If the customers’ quality assurance includes the testing of thermoplastic materials, the test criteria should specify the physical property of the ASTM specification that is most critical to its application. Polymer type alone may not be adequate for the selection of the thermoplastic that is best suited for a specific application. Buyer acknowledges the use of its own knowledge, expertise, skill, experience and judgment in the selection of products(s) and /or in the selection, provision, or designation of any specifications or set of specifications for a product(s) agreed upon by the Buyer and Seller. Buyer acknowledges that Seller shall not be liable for, and Buyer assumes all risk of, inaccurate or unsuitable specifications or information provided, selected or designed by the Buyer. RM BILTRITE™ LLC MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE SUITABILITY OF MATERIALS FOR A PARTICULAR PURPOSE. BUYERS AND USERS MUST DETERMINE THE SAFETY AND SUITABILITY OF RM BILTRITE™ LLC’S PRODUCTS FOR THEIR OWN PURPOSES, AND ASSUME ALL RISK, RESPONSIBILITY, AND LIABILITY FOR ALL INJURIES, LOSSES, OR DAMAGES ARISING FROM THE APPLICATION OF THE INFORMATION OR USE OF RM BILTRITE™ LLC’S PRODUCTS, WHETHER OR NOT CAUSED BY RM BILTRITE™ LLC’S NEGLIGENCE OR BASED ON STRICT PRODUCT LIABILITY. Terms and conditions are available upon request.


TUFF TRAC® ACOUSTICAL BARRIER (MLV)

TUFF TRAC® COMMERCIAL KITCHEN FLOORING

RM Biltrite™ Flexgard® & Rubbermax™ Neoprene Rubber is an excellent general purpose polymer for most uses and applications. It has moderate resistance to oil, gasoline, sunlight, ozone, and oxidizing material. Its temperature range and physical toughness makes it an excellent choice for cold temperature flexibility, abrasion resistance, and repeated flexing applications.

Applications: Electrical insulation, wear-resistant pads, vibration pads, isolation mounts, buffers, diaphragms, industrial matting, water retaining structures, and industrial applications such as gaskets, hoses, and corrosion-resistant coatings.

STYLE #121: RUBBERMAX™ NEOPRENE GRADE 1 (ASTM D2000 1BC)

Item ID

Durometer Hardness Tensile Strength (min) Elongation

Compression Set at 212° F (100° C) for

22 Hours

Volume Swell 212° F (100° C)

for 70 hrs in ASTM Oil 903

Temperature RangeColor Finish Surface

Shore A (± 5) psi MPa min % max % max % °F °C

IR121-40 40 1000 6.9 400 80 +120 -20 - +170 -29 - +77 Black Smooth No talc / film liner





RM Biltrite™ Tuff Trac® Acoustical Barrier Mass Loaded Vinyl (MLV) is a high density PVC product engineered to block sound wave transmission and reduce noise. MLV barrier is highly flexible and well-suited for a variety of automotive, industrial, and building applications. All MLV barrier products are manufactured to meet Federal Motor Vehicle Safety Standard No. 302 (FMVSS 302) specifications for fire safety, and are available in a variety of reinforced and non-reinforced materials.

RM Biltrite™ also provides a specialized E84 Class-A MLV barrier in white or black. Excellent for use in high temperature areas where superior flame & smoke resistance is necessary.

RM Biltrite™ Tuff Trac® Commercial Kitchen Flooring provides safety in commercial kitchens and other work environments where floor protection, slip resistance, and easy cleaning are essential. The PVC material does not absorb water and is resistant to many chemicals found in industrial areas. PVC is also resistant to bacteria and mold, and is flame and smoke retardant.

Resistant to: Acrylic Paint, Ammonium Hydroxide, Ammonium Chloride, Animal Fat, Ammonium Sulfate, Benzoic Acid, Bleach, Butyric Acid, Calcium Chloride, Citric Acid, Detergent Solution, Diluted Sulfuric Acid, Ethyl Alcohol, Formaldehyde, Hydrogen Peroxide, Kerosene, Lacquer Spray Paint, Latex Paint, Malic Acid, Methyl Alcohol, Mineral Oil, Salt Water, Sodium Hydroxide, Sodium Hypochlorite, Succinic Acid, Trichloroacetic Acid, Vegetable Oil, and more.

Applications: Commercial kitchens, coolers, and freezers used in universities, fast food restaurants, full service restaurants, retirement facilities, and more.

STIPPLECustom sizes available upon request

STYLE #110: FLEXGARD® ECONOMY NEOPRENE

Item ID

Durometer Hardness Tensile Strength (min) Elongation Temperature Range Color Finish Surface

Shore A (± 5) psi MPa min % °F °C

IR110-40 40 500 3.5 300 -20 - +170 -29 - +77 Black Smooth No talc / film liner





STYLE #125: FLEXGARD® COMMERCIAL NEOPRENE

Item ID



IR125-40 40 900 6.4 300 -20 - +170 -29 - +77 Black Smooth No talc/ film liner





*Custom sizes available upon request

ROLL DIMENSIONSUnits Widths Thicknesses

U.S. 36” 48” 1/16” 3/32” 1/8” 3/16” 1/4” 3/8” 1/2” 3/4” 1”Metric 91.4 cm 121.9 cm 1.6 mm 2.4 mm 3.2 mm 4.8 mm 6.4 mm 9.5 mm 12.7 mm 19.1 mm 25.4 mm

COMMERCIAL KITCHEN FLOORINGThicknesses

Polymer Finish Back ColorU.S. Metric

.25" 6.4 cm PVC Stipple Textured Grey

Custom sizes available upon request

ACOUSTICAL BARRIER (MLV)Weights Width x Length

Finish ColorU.S. Metric U.S. Metric

.75 lb/ft2 3.7 kg/m2

48" x 25'or

54" x 30'

122 cm x 7.6 mor

137 cm x 9.1 mSmooth Black

1.0 lb/ft2 4.9 kg/m2

1.5 lb/ft2 7.3 kg/m2

2.0 lb/ft2 9.8 kg/m2

Frequency (Hz) where STC= 26 (1 lb rating)

Tran

smis

sion

Lo

ss (

dB)

®RUBBER

RUBBERMAX™ NEOPRENE

RUBBERMAX™ NITRILE

524

RM Biltrite™ Tuff Trac® PVC Roof Walkway is a safe, simple, and economical way to protect rooftops from damage caused by foot traffic and maintenance equipment. Perfect to use as walkways for workers accessing air conditioning, water supply, or electrical equipment. PVC Roof Walkways protect the roof membrane by cushioning impact, absorbing shock, and acting as a barrier from outside elements.

High Profile Herringbone-Embossed Pattern: Engineered for rooftops where heavy foot traffic, impact from dropped tools, and damage from equipment edges are expected.

Low Profile Pyramid-Embossed Pattern: Provides excellent protection and slip reduction for rooftops with normal traffic and servicing. Easy to install.

Applications: Rooftop access points (ladders, hatches, doorways), protection from window washing equipment and around rooftop equipment that require periodic maintenance.

PYRAMID

RM Biltrite™ Flexgard® & Rubbermax™ Nitrile Rubber, also known as Buna-N, acrylonitrile butadiene rubber, and NBR, is a synthetic rubber copolymer of acrylonitrile (ACN) and butadiene. It has generally strong resistance to oil, fuel, petroleum based hydraulic fluids, aliphatic hydrocarbons, and hydrocarbon solvents, as well as alkalis, acids, and other chemicals. Like natural rubber, nitrile can be damaged by ozone, ketones, esters and aldehydes. It is more resistant than natural rubber to oils and acids, and has superior strength, but inferior flexibility. Nitrile rubber is less likely to cause an allergic reaction than natural rubber.

Applications: Automotive and aeronautical industry, fuel and oil handling gasket seals, hoses, grommets, self-sealing fuel tanks, molded goods, floor mats, disposable gloves.

*Made with FDA approved ingredients

®

TUFF TRAC® PVC WALKWAY

HERRINGBONE



STYLE #201: RUBBERMAX™ NITRILE GRADE 1 (ASTM D2000 1BF)

Item ID



22 Hours










STYLE #221: RUBBERMAX™ WHITE FDA NITRILE GRADE 1 (ASTM D2000 1BF)

Item ID



22 Hours





IR221-50 60 1000 6.9 270 50 +60 -20 - +170 -29 - +77 White Smooth No talc / film liner

IR221-60 60 1000 6.9 250 50 +60 -20 - +170 -29 - +77 White Smooth No talc / film liner

STYLE #205: FLEXGARD® COMMERCIAL NITRILE

Item ID











FLEXGARD® NITRILE

1) Custom sizes available upon request 2) Optional yellow safety edge available

HERRINGBONE PVC WALKWAYUnits Widths Thicknesses Lengths Weight Color

U.S. 30" .156" 50' 125 lbsGrey

Metric 76.2 cm 3.9 mm 15.2 m 56.7 kg


PYRAMID PVC WALKWAYUnits Widths Thicknesses Lengths Weight Color

U.S. 36" .090" 60' 90 lbs Grey or TanMetric 91.4 cm 2.3 mm 18.3 m 40.8 kg

236

RUBBERMAX™ NATURAL RUBBER

RM Biltrite™ Flexgard® & Rubbermax™ EPDM Rubber provides superior properties for outdoor and high temperature applications. It has excellent resistance to heat, ozone and sunlight. It is also extremely resistant to oxidation, UV rays, and ozone, and displays good resistance to alkalis, acids and oxygenated solvents. EPDM has good temperature flexibility, enabling superior resistance to water and steam.

Applications: Window seals, liners, insulation, anti-vibration, outdoor UV and ozone uses.

RM Biltrite™ Flexgard® Natural Rubber (NR) has low compression set, high tensile strength, superior resilience, good abrasion and tear resistance, and good vibration dampening characteristics. Not recommended for hydrocarbons, ozone, UV and contact with strong acids. Manufactured from FDA approved ingredients with a tan color and smooth finish.

Applications: Automotive, building, and chemical industries, O-rings, rubber seals, molded rubber components, rubber-to-metal bonded vibration isolators and mounts. *Floating stock

*Made with FDA approved ingredients

RM Biltrite™ Tuff Trac® TPO Roof Walkway is a safe, simple, and economical way to protect rooftops from damage caused by foot traffic and maintenance equipment. TPO Roof Walkway also provides anti-slip protection for employees accessing air conditioning, water supply, or electrical equipment. It protects the roof membrane by cushioning impact, absorbing shock, and acting as a barrier from outside elements. TPO Roof Walkway is engineered for outdoor use and will not expand or contract. Easy to install.

Applications: Rooftop access points (ladders, hatches, doorways), protection from window washing equipment and around rooftop equipment that require periodic maintenance.

TUFF TRAC® TPO WALKWAY



STYLE #441: RUBBERMAX™ FDA NATURAL RUBBER GRADE 1 (ASTM D2000 1AA)

Item ID



22 Hours


Shore A (± 5) psi MPa min % max % °F °C

IR441-40 40 3000 20.7 600 50 -20 - +140 -29 - +60 Tan Smooth No talc / film liner

STYLE #300: FLEXGARD® COMMERCIAL EPDM

Item ID






STYLE #301: RUBBERMAX™ EPDM GRADE 1 (ASTM D2000 1BA)

Item ID



22 Hours


Shore A (± 5) psi MPa min % max % °F °C

IR301-40 40 800 5.5 300 50 -40 - +212 -40 - +100 Black Smooth No talc / film liner







WHITE GREY

®RUBBER

FLEXGARD® & RUBBERMAX™ EPDM


DIAMOND TPO WALKWAY WITH YELLOW SAFETY EDGEUnits Widths Lengths Thicknesses Weight Color

U.S. 34" 50' .170" 86 lbs White or GreyMetric 86.4 cm 15.2 m 4.3 mm 39 kg

WHITE GREY

1) Custom sizes available upon request 2) Optional yellow safety edge available

HERRINGBONE TPO WALKWAYUnits Widths Thicknesses Lengths Weight Color

U.S. 30" .156" 50' 78 lbs White or GreyMetric 76.2 cm 3.9 mm 15.2 m 35.4 kg

722

RUBBERMAX™ CSM (HYPALON®)

RM Biltrite™ Flexgard® SBR Rubber is a copolymer of styrene and butadiene and has properties similar to natural rubber. Compared to natural rubber, SBR has superior processability, heat aging, and abrasion resistance but inferior elongation, hot tear strength, resilience and tensile strength. SBR has excellent mechanical properties, low compression set, and high resilience. It also has excellent dynamic and rebound properties and exhibits good resistance to acids, brake fluids, moisture, alkalis and salts. SBR may be substituted for natural rubber in certain applications, offering significant cost savings. Not recommended for use in proximity to oils and hydrocarbons. An economical red or black sheet can be used in low pressure applications with no oil resistance requirements.

Applications: HVAC and construction industry, hydraulic brake system seals and diaphragms, mechanical rubber parts, panel grommets and body pads.

RM Biltrite™ Rubbermax™ Hypalon® Rubber, also known as CSM, is a premium grade synthetic rubber. It is flame resistant and offers strong resistance to most chemicals, alkalis, acids, oils, and heat. CSM rubber also display good electrical properties and color stability, along with good weather and abrasion resistance.

Applications: Waterproofing, acid and alkaline proofing, hoses, cable sheathing, inflatables, roofing.

TUFF TRAC® ESD MATTING TUFF TRAC® CONDUCTIVE MATTING FLEXGARD® SBR

RM Biltrite™ Tuff Trac® ESD Matting provides crucial safety in environments where people or products are at risk of harm from static charge.

Tuff Trac® ESD Single Layer is made with a proprietary blend of polymers and migratory anti-static components. The anti-static components are homogeneously dispersed and continually migrate to the surface. This specialized blend has high hydrophilic properties, ensuring a micro-thin layer of water on the surface to assist the flow of static charge. The blend also contains polymers which actively control dissipation by slowing its speed. Tuff Trac® ESD Single Layer delivers a resistance of 108-109.

Tuff Trac® ESD Dual Layer is made with the same proprietary blend of polymers and migratory anti-static components as ESD Single Layer and is permanently bonded to a 5mm conductive polymer layer on the backside for additional performance. The conductive polymer bonding produces an electrical rating of 106-108, making the Dual Layer's surface less hydrophilic and less dependent on room humidity.

Conductive PVC layer

Staticdissipative

top layer

Continuous path toground for rapiddissipation

RM Biltrite™ Tuff Trac® Conductive Matting provides crucial safety in environments where people or equipment are at risk of harm from stronger electrical charges. Our conductive matting is manufactured from PVC engineered vinyl and consists of a highly conductive cap film bonded to a non-conductive base. It has a homogeneous distribution of carbon black and proprietary polymers to provide a continuous and permanent path-to-ground.

Along with electrical floor protection, conductive matting also provides anti-fatigue comfort for employees. All conductive matting is fabricated to ANSI/ESD S7. 1-2005 standards and tests in the optimal electrical rating range of 104-106. Recommended for usage in environments with rapid (nanoseconds) decay/dissipation. Requires grounding clips for full safety and performance.

SMOOTHSTIPPLEDIAMOND

*Custom sizes available upon request

Custom sizes available upon request Optional yellow safety edge available



STYLE #400: FLEXGARD® RED COMMERCIAL SBR

Item ID



IR400-75 75 400 2.8 150 -20 - +170 -29 - +77 Red Smooth No talc / film liner

STYLE #405: FLEXGARD® BLACK COMMERCIAL SBR

Item ID




STYLE #620: RUBBERMAX™ HYPALON® GRADE 1 (ASTM D2000 1CE)

Item ID



22 Hours






IR620-70 70 1000 6.9 400 40 --- -22 - +266 -30 - +130 Black Smooth No talc / film liner


SBR & HYPALON® ROLL DIMENSIONSUnits Widths Thicknesses



ESD SINGLE LAYER MATTINGThicknesses


.060" 1.5 mm PVC Stipple Smooth Blue or Grey

CONDUCTIVE PVC MATTINGThicknesses

Finish ColorU.S. Metric

.156" 4.0 mm Diamond Black

.080" 2.0 mm Smooth or Stipple Black

.125" 3.2 mm Smooth or Stipple Black

ESD DUAL LAYER MATTINGThicknesses


.060" 1.5 mm PVC Stipple Smooth Blue or Grey

.156" 4.0 mm PVC Diamond Textured Black

®RUBBER


218

FLEXGARD® CLOTH-INSERTED (CI)

RM Biltrite™ Flexgard® Cloth-Inserted (CI) Rubber is reinforced with one or more plies of Nylon 6 fabric. Nylon 6 fabric insertion increases stability during applications using mechanical fastening, and reduces creep during high compression load handling. Cloth-Inserted rubber is available with either SBR or neoprene rubber, with both regular ply (one ply of fabric for each 1/16” thickness) and reduced ply (one ply of fabric for each 1/8” thickness) options.

Applications: Conveyor belts, gaskets, mechanical fastening, uses requiring petroleum, detergents and heavy oil resistance, environments with water & gas.

®

RM Biltrite™ Tuff Trac® Military Electrical Grade (MEG) Vinyl Switchboard Matting is manufactured with a combination of flame retardants and smoke suppressants to meet stringent flame and smoke density standards required for MIL-DTL-15562G specification. All military grade rolls are marked on the back with the specification, month, and year of manufacture to guarantee compliance with MIL-DTL-15562G requirements. RM Biltrite™ MEG Matting is approved for use by all subordinates of the Department of Defense, including the U.S. Navy.

Type I: Smooth sheet; comes in a marbleized beige, blue, green, or grey color. Typically used as floor covering for glue down installations in high voltage areas. Can be installed with heat or chemically sealed seams to create a watertight protective surface.

Type II: Smooth runner; comes in blue, green, or black color. Designed for single strip use as portable floor mats around electrical devices or electrical areas. Provides the same insulation and fire/smoke resistance as Type I.

Type III: Mat/Runner with raised diamond plate finish; comes in green or grey color. Designed to be used as a removable runner around electrical equipment or areas where electrical hazards may exist. Provides extra slip protection and the same insulation and fire/smoke resistance as Type I.

TUFF TRAC® MILITARY GRADE VINYL SWITCHBOARD

TYPE I

TYPE II

TYPE III




Berry Amendment Compliant

Made in

USA




STYLE #530: FLEXGARD® COMMERCIAL SBR - REDUCED PLY

Item ID

Durometer Hardness Tensile Strength (min) Elongation Temperature Range Fabric 0.3716 oz/ft2

(113.39 g/m2)Color Finish Surface


IR530-70 70 400 2.8 200 -20 - +170 -29 - +77 Nylon 6 Black Smooth No talc / film liner

STYLE #530 ROLL DIMENSIONS

Units Widths Thicknesses

U.S. 48" 1/ 8” 1 Ply 3/ 16” 2 Ply 1/ 4” 3 PlyMetric 121.9 cm 3.2 mm 1 Ply 4.8 mm 2 Ply 6.4 mm 3 Ply


STYLE #510: FLEXGARD® COMMERCIAL SBR - REGULAR PLY

Item ID







U.S. 48" 1/ 16” 1 Ply 1/ 8” 2 Ply 3/ 16” 3 Ply 1/ 4” 4 PlyMetric 121.9 cm 1.6 mm 1 Ply 3.2 mm 2 Ply 4.8 mm 3 Ply 6.4 mm 4 Ply


STYLE #550: FLEXGARD® COMMERCIAL NEOPRENE - REGULAR PLY

Item ID







U.S. 48" 1/ 16” 1 Ply 1/ 8” 2 Ply 3/ 16” 3 Ply 1/ 4” 4 PlyMetric 121.9 cm 1.6 mm 1 Ply 3.2 mm 2 Ply 4.8 mm 3 Ply 6.4 mm 4 Ply

TYPE I MEG MATTINGWidths Lengths Thicknesses

Cut Finish ColorU.S. Metric U.S. Metric U.S. Metric

36" 91.4 cm 75' 22.9 m 0.125" 3.2 mm Sheet Smooth Marbleized Beige, Blue, Green, or Grey

TYPE II MEG MATTINGWidths Lengths Thicknesses


36" 91.4 cm 75' 22.9 m 0.125" 3.2 mm Runner Smooth Blue, Green, or Black

TYPE III MEG MATTINGWidths Lengths Thicknesses


36" 91.4 cm 75' 22.9 m 0.188" 4.8 mm Mat/Runner Raised Diamond Plate Blue, Green, or Black

920

RUBBERMAX™ DIAPHRAGM

RM Biltrite™ Rubbermax™ Diaphragm Rubber is manufactured with a high quality nitrile rubber compound designed for prolonged wear and use. The rubber is then inserted with a Nylon 6 cloth for maximum strength and durability. Cloth insertion can be provided with either 1 or 2 ply reinforcement.

Applications: Oil, liquid petroleum gas, and other solvent resistant applications, control valves, regulators, differential pressure pumps.

RM Biltrite™ Tuff Trac® ASTM Vinyl Switchboard Matting insulates employees from electrical shock by interrupting the electrical path-to-ground. Perfect for use in high voltage areas and around high voltage equipment.

RM Biltrite™ has over forty years of experience manufacturing switchboard matting from both rubber and vinyl. Our Tuff-Trac® Type II Class 2 formula, developed after years of research and testing, contains polymers enriched with functional additives which provide greater insulative resistance. All Tuff-Trac® Type II Class 2 matting is verified for dielectric resistance to 30,000 VAC per ASTM D-178. In addition, RM Biltrite™ performs extreme testing on every production batch to confirm our formula delivers a higher margin of safety up to 50,000 VAC. Matting is branded on back per ASTM specification.

Tuff-Trac® Switchboard Matting is also available in military specification grade MIL-DTL-15562, currently used by the U.S. Navy.

TUFF TRAC® VINYL SWITCHBOARD MATTING



STYLE #570: RUBBERMAX™ NITRILE DIAPHRAGM GRADE 1 (ASTM D2000 1BF) - REGULAR PLY

Item ID

Durometer Hardness

Tensile Strength (min) Elongation


22 Hours



Temperature RangeFabric Color Finish Surface


IR570-70 70 1100 7.6 250 25 +25 -22 - +230 -30 - +110 Nylon 6 Black Smooth No talc / film liner


STYLE #570 ROLL DIMENSIONSUnits Widths Thicknesses

U.S. 36” 48” 1/16” 1 Ply 1/8” 2 Ply 3/16” 3 Ply 1/4” 4 PlyMetric 91.4 cm 121.9 cm 1.6 mm 3.2 mm 4.8 mm 6.4 mm

STYLE #560: RUBBERMAX™ NITRILE DIAPHRAGM GRADE 1 (ASTM D2000 1BF) - REGULAR PLY

Item ID

Durometer Hardness

Tensile Strength (min) Elongation


22 Hours



Temperature RangeFabric Color Finish Surface





STYLE #560 ROLL DIMENSIONSUnits Widths Thicknesses

U.S. 36” 48” 1/16” 1 Ply 1/8” 2 Ply 3/16” 3 Ply 1/4” 4 PlyMetric 91.4 cm 121.9 cm 1.6 mm 3.2 mm 4.8 mm 6.4 mm

sTuff Trac® Type II Switchboard is proof tested to 50,000 volts

SWITCHBOARD CLASS GUIDE

Type & ClassThicknesses

Dielectric Test Voltage Recommended Maximum VAC UsageU.S. Metric

Type II, Class 1 3/16” 4.8 mm 20,000 VAC 7,500 VACType II, Class 2 1/4” 6.4 mm 30,000 VAC 17,000 VAC

CORRUGATEDCustom sizes available upon request

CORRUGATED SWITCHBOARD MATTING


Polymer ColorU.S. Metric

Type II, Class 1 3/16” 4.8 mmPVC Black

Type II, Class 2 1/4” 6.4 mm

DIAMONDCustom sizes available upon request

DIAMOND SWITCHBOARD MATTING


Polymer ColorU.S. Metric

Type II, Class 1 3/16” 4.8 mmPVC Black

Type II, Class 2 1/4” 6.4 mm

TUFF TRAC® VINYL MATTING

1910

FLEXGARD® SILICONE

RM Biltrite™ Flexgard® Silicone Rubber has a wide temperature range, enabling it to retain its initial shape and mechanical strength and operate normally overall in extreme temperatures. Several of silicone rubber's technical specifications are far superior to organic rubbers at such temperatures. Unlike organic rubbers, silicone can well withstand ozone, UV, heat and other aging factors. It is also highly inert and does not react with most chemicals, making it suitable for medical applications such as implants, tubing, and catheters. Silicone is biocompatible and both hypoallergenic and non-allergenic, making it a safe choice for baby care products and food contact purposes. It exhibits strong chemical stability, preventing it from affecting any substrates that come in contact such as skin, water, blood, and active ingredients.

Applications: Automotive, food, electronic, medical, construction, and pharmaceutical industries, outdoor, extreme environments, and manufacturing uses.

®

* ZZR765 (A-A-59588) ASTM D2000 M1GE

RM Biltrite™ Tuff Trac® Vinyl Matting is manufactured from a special proprietary blend of new and recycled materials engineered to provide superior performance and durability. Vinyl matting products improve employee comfort and safety in busy environments like manufacturing, healthcare, and warehousing workplaces. RM Biltrite™ provides five different matting finish designs for all customer needs. Good for use where slip and wear protection is important and public areas with heavy foot traffic.

CORRUGATED

EASY SWEEP

DIAMOND



STYLE #715: FLEXGARD® COMMERCIAL SILICONE

Item ID








STYLE #735: FLEXGARD® SILICONE SPECIFICATION* GRADE

Item ID











CORRUGATED VINYL MATTINGWidths Thicknesses Lengths

ColorU.S. Metric U.S. Metric U.S. Metric

24" 60.9 cm1/8” 3.2 mm 105' 32.0 m

Black

1/4” 6.4 mm 75' 22.9 m

30" 76.2 cm

3/32” 2.4 mm105' 32.0 m

1/8” 3.2 mm1/4” 6.4 mm 75' 22.9 m

36" 91.4 cm1/8” 3.2 mm 105' 32.0 m1/4” 6.4 mm 75' 22.9 m

48" 121.9 cm

3/32” 2.4 mm105' 32.0 m

1/8” 3.2 mm1/4” 6.4 mm 75' 22.9 m

PYRAMID VINYL MATTINGWidths Thicknesses Lengths


24" 60.9 cm

1/8” 3.2 mm 105' 32 m Black30" 76.2 cm

36" 91.4 cm

48" 121.9 cm

60" 152.4 cm

ELDORADO VINYL MATTINGWidths Thicknesses Lengths


30" 76.2 cm

.075" 1.9 mm 105' 32 m Black36" 91.4 cm

48" 121.9 cm

60" 152.4 cm

EASY SWEEP VINYL MATTINGWidths Thicknesses Lengths


24" 60.9 cm

1/8” 3.2 mm 105' 32 m Black30" 76.2 cm

36" 91.4 cm

48" 121.9 cm

60" 152.4 cm




DIAMOND PLATE VINYL MATTINGWidths Thicknesses Lengths


24" 60.9 cm

5/ 32” 3.9 mm 75' 22.9 m Black30" 76.2 cm

36" 91.4 cm

48" 121.9 cm

60" 152.4 cm

1) Custom sizes available upon request 2) *Optional yellow safety edge available

PYRAMID

ELDORADO

FLEXGARD® FLUOROELASTOMER (FKM, VITON®)

1118

RM Biltrite™ Flexgard® Fluoroelastomer Rubber, also known as FKM or Viton®, is a high-performance elastomer valued for its excellent heat stability and strong resistance to aggressive fuels and chemicals. FKM performs a broad range of resistances when exposed to oils, fuels, lubricants, and most mineral acids. It also has good resistance to many aliphatic hydrocarbon fluids used as solvents in other rubbers. FKM exhibits exceptionally good compression set characteristics at high temperatures and good resistance to atmospheric oxidation, sun and weather exposure, fungus and mold.

Applications: Automotive, fluid power, appliance and chemical industries, fuel system seals, expansion joints and gaskets.

®

FLEXGARD® DURA-TRANZ®

RM Biltrite™ Flexgard® Dura-Tranz® Rubber Transit Flooring enhances the look of any vehicle while providing better walking comfort, slip resistance, anti-fatigue, anti-bacteria, noise reduction, and fire safety than other hard surface floorings.

Dura-Tranz® is scratch resistant, has high dimensional stability, and cleans easily with regularly available floor cleaning solutions. It is very low maintenance flooring option in comparison to wood and carpet. Dura-Tranz® does not require any waxing, polishing, scrubbing, sanding, or refinishing. Product can be laid loosely on top of previous flooring or bonded directly to the floor itself.

RM Biltrite™ supplies Dura-Tranz® in rolls with a smooth or ribbed finish and smooth, sandpaper, or fabric backing. Dura-tranz® is available in solid and marble patterns and comes in a wide range of colors for easy, customizable design creation. Custom colors can be provided upon request. Also available as one-piece flooring for automobiles.

FIRE GUARD

Technical Specifications

• Fire Propagation to BS 476 prt 6• Surface Spread flame to BS 476 prt 6• Ignitability to BS 476 prt 12• Reaction to fire: BS ISO 9239-1• Smoke Density to BS 6853:1999 • Smoke Toxicity to BS:6853:1999 • Temperature Index to BS 6853:1999• Slip Resistance to SATRA PM 144• Light reflectance > 35%• Abrasion resistance to DIN 53 519• Graffiti resistance to E6264• Chemical resistance to E6264• Lightfastness to E6264 E2• Spec. gravity to BS 903 prt A2• Hardness to BS 903 prt A1• Tensile strength to BS 903 prt A2• Elongation to BS 903 prt A2• Chemical resistance to BS 905• Smoke Index to NES 711• Toxicity index to NES 713• Oxygen index to NES 714• Temperature index to NES 715

Dura-Tranz® Fire Guard is developed for military applications where fire safety standards are absolutely critical, such as battleships and submarines. Its quality and functionality make it an excellent floor covering option for interior use in passenger liners, ferries, cruise ships, tankers, container ships and marine ships. Duro-Tranz® Fire Guard flooring can also be used in underground metro rail cars where fire safety is a top priority. It is fire rated class 0 by Warrington Fire Labs U.K. Available with fabric finish.

FIRE SAFE

Dura-Tranz® Fire Safe is a custom made range of synthetic rubber floor coverings it is designed to meet requirement of tunnel (both single and multi track) railway system to BS 6853:1999 CAT 1A and 1B. Dura-Tranz® Fire Safe flooring is recommended for high traffic areas where higher safety standards are required. It is flame resistant and comes with a M1 (Class 1) classification tested at Warrington Fire UK. Available in plain, speckle or marble Finishes.


• Surface spread of flame to BS 476 Pt 7 • Smoke Test to BS 6853:1999 D8.6• Toxicity Test to BS 6853:1999 B4.2• Fire Behavior to BS 6853:1999 • Fire Behavior to BS 476 Pt 6• Slip Resistance to SATRA TM 144• Slip Resistance to BS 7976-2 2002• Abrasion Resistance to ASTM D4060• Abrasion Resistance to DIN 53 516• Specific Gravity to DIN 53 508• Hardness to DIN 53 505• Tensile strength to DIN 53 504 • Elongation to DIN 53 504 (Plain)• Graffiti Resistance to E6264• Chemical Resistance to E6264

FIRE SHIELD

Dura-Tranz® Fire Shield is class 2 fire retardant flooring. This flooring is an appropriate covering for schools, hospitals, airports, and workshops. The flooring has a higher coefficient of friction to prevent slips and falls.


• Surface spread of flame to BS 476 Pt. 7• Smoke Test to BS 6853: 1999 D8.6• Smoke Toxicity Test to BS 6853:1999 B4.2• Fire Behavior to BS 6853:1999• Slip resistance to SATRA TM144• Slip Resistance to BS 7976-2 2002• Abrasion Resistance to ASTM D4060• Abrasion Resistance to DIN 53 516• Specific Gravity to DIN 53 508 • Hardness to DIN 53 505• Tensile strength to DIN 53 504• Elongation to DIN 53 504 • Compression Set to DIN 53

®



STYLE #865: FLEXGARD® COMMERCIAL FKM

Item ID

Durometer Hardness

Tensile Strength (min) Elongation Tear Density Temperature Range Color Finish Surface

Shore A (± 5) psi MPa min % lb/in kg/cm g/cm3 °F °C

IR865-75 75 700 4.8 200 112 20 2.05 -22 - +482 -30 - +250 Black Smooth No talc / film liner


Item ID

Durometer Hardness

Tensile Strength (min) Elongation Tear Density Temperature Range Color Finish Surface

Shore A (± 5) psi MPa min % lb/in kg/cm g/cm3 °F °C

IR867-75 75 1000 6.9 200 101 18 1.95 -22 - +482 -30 - +250 Black Smooth No talc / film liner


Item ID

Durometer Hardness

Tensile Strength (min) Elongation Tear


22 Hours

Density Temperature RangeColor Finish Surface

Shore A (± 5) psi MPa min % lb/in kg/cm max % g/cm3 °F °C

IR870-75 75 1420 9.8 250 168 30 +50 1.95 -22 - +482 -30 - +250 Black Smooth No talc / film liner

STYLE #872: FLEXGARD® COMMERCIAL VITON®

Item ID

Durometer Hardness

Tensile Strength (min) Elongation Tear


22 Hours

Density Temperature RangeColor Finish Surface

Shore A (± 5) psi MPa min % lb/in kg/cm max % g/cm3 °F °C

IR872-75 75 1280 8.8 180 168 30 +50 2.00 -22 - +482 -30 - +250 Black Smooth No talc / film liner




12

FLEXGARD® BUTYL

17

RM Biltrite™ Flexgard® Butyl Rubber is a copolymer of isobutylene and isoprene. It has outstanding resistance to gases, vapors, heat aging, oxygen, ozone, sunlight, tearing, alkalis, and acids. Butyl has good flex and low resilience properties, making it ideal for vibration damping, insulation, and shock absorption. It also offers moderate resistance to abrasion and compression set. Butyl rubber is resistant to most inorganic products and is highly resistant to mineral acids, alkaline and aqueous acids.

Documents

RM Biltrite Sheet Rubber Catalogue 2018bostonfloormats.com/sites/default/files/RM Biltrite Sheet...experienced compounders. We recommend self-testing polymers as we cannot guarantee