Rivets New Pgs-03 · Mandrel: Aluminum Alloy 7178, 7075, 5056 or 2024 or equivalent alloy. Shear Strength Rivets shall have ultimate shear loads not less than the minimum ultimate

Rivets

177

DimensionsMechanical and Performance Requirements

Standard Blind RivetsAluminum/Aluminum, Dome Head............. 178-179Aluminum/Steel, Dome Head ...................... 180-181Steel/Steel, Dome Head ............................... 182-183Large Flange, All Materials ......................... 184-185

Closed End, Aluminum/Steel, Dome Head ................ 186

Copper/Copper Plated Steel, Dome Head .................. 187

Stainless/Stainless, Dome Head ................................. 188

Application Data for Standard Blind Rivets ............... 189

Multi-Grip RivetsLow Profile Head, Aluminum/Steel ..................... 190Dome Head, Aluminum/Steel .............................. 191Large Flange, Aluminum/Steel ............................ 192Countersunk Head, Aluminum/Steel ................... 193Dome Head, Steel/Steel ....................................... 194Large Flange, Steel/Steel ..................................... 194Countersunk Head, Steel/Steel ............................. 194Dome Head, Type US, Steel/Steel ....................... 195Dome Head, Stainless/Stainless ........................... 196

3-Star Bulbing Style, Aluminum/Aluminum .............. 197

Drive PinsBrazier Head ........................................................ 198Countersunk Head ................................................ 199Liner Head............................................................ 200Universal Head ..................................................... 201

DimensionsMechanical and Performance Requirements

Semi-Tubular RivetsOval Head ............................................................ 202Truss Head ........................................................... 2031200 Countersunk Flat Head ................................ 2041500 Countersunk Flat Head ................................ 205

Solid RivetsButton Head ......................................................... 206Pan Head .............................................................. 207Flat Head .............................................................. 208Flat Countersunk Head ........................................ 209

Split RivetsOval Head ............................................................ 210Flat Countersun Head .......................................... 211

Full-Tubular RivetsOval Head ............................................................ 212Truss Head ........................................................... 212Flat Countersunk Head ........................................ 212

High Strength, Double Locking RivetsOrlock® Brand, Dome Head ................................. 213Orlock® Brand, Countersunk Head ...................... 213

Monobolt® Structural Rivets ....................................... 215

®Orlock is a registered trademark owned by Ornit.®Monobolt is a registered trademark of the Avdel Cherry Textron Corporation. Kanebridge’s rivets are not manufactured by or connected with the producers ofMonobolt® rivets.

Rivets

178

Aluminum Rivet/Aluminum Mandrel

Dome HeadBlind Rivet

LE

HW D

P F‡

DescriptionAn aluminum blind fastener which has a self-contained mechanical feature (a mandrel) which permits the formation of an upset on

the blind end of the rivet and expansion of the rivet shank during rivet setting to join the component parts of an assembly. Thealuminum mandrel is pulled into or against the rivet body, breaking at or near the junction of the mandrel shank and its upset end.

The dome head is slightly rounded and twice as wide as the body diameter.

Applications/Advantages

Dome head is the most commonly specified head style because of its low profile and neat, finished appearance.Aluminum/aluminum rivets have the lowest tensile and shear values of all break mandrel rivets. They should be used when

fastening materials with similar mechanical and physical properties.

MaterialRivet: Aluminum Alloy 5050 or 5052 or equivalent alloy. Rivets have no additional finish except for sizes #42 & 44 which are also

available painted white.Mandrel: Aluminum Alloy 7178, 7075, 5056 or 2024 or equivalent alloy.

Shear Strength Rivets shall have ultimate shear loads not less than the minimum ultimate shear loads specified for the applicable size given in theabove table.

Tensile Strength Rivets shall have ultimate tensile loads not less than the minimum ultimate tensile loads specified for the applicable size given inthe above table.

Mandrel BreakLoad

While the rivet is being set, the axially applied load necessary to break the mandrel shall be within the limits specified for theapplicable rivet size given in the above table.

ALUMINUM BODY/ALUMINUM MANDREL DOME HEAD BREAK-STEM BLIND RIVETS SAE J-1200

NominalRivet

Diameter

D H E W P F UltimateShearLoad

UltimateTensileLoad

Mandrel BreakLoadRivet Shank

DiameterHead Diameter Head

HeightMandrelDiameter

MandrelProtrusion

Blind SideProtrusion

Max Min Max Min Max Nom Min Max Min, lb. Min, lb. Max Min

3/32 0.096 0.090 0.198 0.178 0.032 0.057 1.00 L + 0.100 70 80 240 140

1/8 0.128 0.122 0.262 0.238 0.040 0.076 1.00 L + 0.120 120 150 400 250

5/32 0.159 0.153 0.328 0.296 0.050 0.095 1.06 L + 0.140 190 230 600 425

3/16 0.191 0.183 0.394 0.356 0.060 0.114 1.06 L + 0.160 260 320 825 625

1/4 0.255 0.246 0.525 0.475 0.080 0.151 1.25 L + 0.180 460 560 1400 1100

Rivets

179


Aluminum Rivet/Aluminum Mandrel

PART NUMBER COMPARISON - DOME HEAD ALUMINUM RIVET/ALUMINUM MANDREL

Kanebridge Huck/Automatic

Pop ® Marson/Creative

Star Celus ® Cherry Gesipa ®

ADA41 ABA41 AD41ABS AB4-1A 4-1AAD A/A 41D AAP-41 GAMD41A








ADA53 ABA53 AD53ABS AB5-3A 5-3AAD A/A 53D - GAMD53A




ADA510 ABA510 - - - A/A510D AAP-510 -

ADA512 - - - - - - -





ADA610 ABA610 AD610ABS AB6-10A 6-10AAD A/A610D AAP-610 GAMD610A

ADA612 ABA612 AD612ABS AB6-12A 6-12AAD A/A612D AAP-612 GAMD612A

ADA614 ABA614 - - - A/A614D AAP-614 GAMD614A

ADA616 ABA616 AD616ABS AB6-16A - A/A616D AAP-616 GAMD616A

ADA618 ABA618 - - - - - -

®Celus is a registered trademark of Celus Fasteners Manufacturing Inc..®Gesipa is a registered trademark of Gesipa Fasteners USA Inc..®Pop is a registered trademark of Pop Fastening Systems, Emhart Fastening Teknologies, a Black & Decker Company.Kanebridge’s rivets are not manufactured by or connected with the producers of Gesipa® or Pop® rivets.

Rivets

180

‡LE

HW D

P F

Aluminum Rivet/Steel Mandrel


DescriptionAn aluminum blind fastener which has a self-contained steel mandrel which permits the formation of an upset on the blind end of

the rivet and expansion of the rivet shank during rivet setting to join the component parts of an assembly. The steel mandrel ispulled into or against the rivet body, breaking at or near the junction of the mandrel shank and its upset end. The head of the body

is slightly rounded and twice as wide as the body diameter.


Dome head is the most commonly specified head style because of its low profile and neat, finished appearance. The steel mandrelgives this style rivet greater tensile and shear values than aluminum rivets with aluminum mandrels. They should be used when

fastening materials with similar mechanical and physical properties.

MaterialRivet: Aluminum Alloy 5056 or 5154 or equivalent alloy. Rivets have no additional finish except for sizes #42 & 44 which are alsoavailable painted white. Note: Some manufacturers use aluminum alloy 5052 which is acceptable but will lower the shear, tensile

and mandrel break load standards to those of aluminum rivets with aluminum mandrels (see page 144).Mandrel: Carbon steel 1006 or equivalent. May be furnished plain or with a protective coating, at the option of the manufacturer.



Mandrel BreakLoad


ALUMINUM BODY/STEEL MANDREL DOME HEAD BREAK-STEM BLIND RIVETS SAE J-1200

NominalRivet

Diameter


UltimateTensileLoad


DiameterHead Diameter

HeadHeight

MandrelDiameter

MandrelProtrusion



3/32 0.096 0.090 0.198 0.178 0.032 0.057 1.00 L + 0.100 90 120 275 175

1/8 0.128 0.122 0.262 0.238 0.040 0.076 1.00 L + 0.120 170 220 600 400

5/32 0.159 0.153 0.328 0.296 0.050 0.095 1.06 L + 0.140 260 350 850 600

3/16 0.191 0.183 0.394 0.356 0.060 0.114 1.06 L + 0.160 380 500 1050 750

1/4 0.255 0.246 0.525 0.475 0.080 0.151 1.25 L + 0.180 700 920 1850 1450

Rivets

181


Aluminum Rivet/Steel Mandrel

PART NUMBER COMPARISON - ALUMINUM RIVET/STEEL MANDREL


Pop ® Marson/Creative

Star Celus ® Cherry Gesipa ®

ADS31 - - - - - - -

ADS32 ABS32 AD32BS AB3-2 - A/S 32D BSP-32 GSMD32A


ADS41 ABS41 AD41BS AB4-1 4-1ASD A/S 41D BSP-41 GSMD41A








ADS53 ABS53 AD53BS AB5-3 5-3ASD A/S 53D - GSMD53A




ADS510 ABS510 - - - A/S510D BSP-510 -

ADS512 - - - - - - -

ADS516 - - - - - - -





ADS610 ABS610 AD610BS AB6-10 6-10ASD A/S610D BSP-610 GSMD610A

ADS612 ABS612 AD612BS AB6-12 6-12ASD A/S612D BSP-612 GSMD612A

ADS614 ABS614 AD614BS - - A/S614D BSP-614 GSMD614A

ADS616 ABS616 AD616BS AB6-16 - A/S616D BSP-616 GSMD616A

ADS618 ABS618 - - - - - -

ADS620 - - - - - - -

ADS622 - - - - - - -




ADS810 ABS810 AD810BS - - A/S810D BSP-810 GSMD810A


Rivets

182

Steel Rivet/Steel Mandrel


LE

HW D

P F‡

DescriptionA carbon steel blind fastener which has a self-contained carbon steel mandrel which permits the formation of an upset on the blind

end of the rivet and expansion of the rivet shank during rivet setting to join the component parts of an assembly. The steel mandrelis pulled into or against the rivet body, breaking at or near the junction of the mandrel shank and its upset end. The head of the

body is slightly rounded and twice as wide as the body diameter.


Dome head is the most commonly specified head style because of its low profile and neat, finished appearance. The all steel designgives this style rivet greater tensile and shear values than all varieties of aluminum rivets. They should be used when fastening

materials similar to carbon steel.

Material Rivet: Low carbon steel, plated zinc.Mandrel: Carbon steel 1006 or equivalent. May be furnished plain or with a protective coating, at the option of the manufacturer.



Mandrel BreakLoad


STEEL BODY/STEEL MANDREL DOME HEAD BREAK-STEM BLIND RIVETS SAE J-1200

NominalRivet

Diameter


UltimateTensileLoad


DiameterHead Diameter Head

HeightMandrelDiameter

MandrelProtrusion



3/32 0.096 0.090 0.198 0.178 0.032 0.057 1.00 L + 0.100 130 170 360 260

1/8 0.128 0.122 0.262 0.238 0.040 0.076 1.00 L + 0.120 260 310 800 600

5/32 0.159 0.153 0.328 0.296 0.050 0.095 1.06 L + 0.140 370 470 1000 750

3/16 0.191 0.183 0.394 0.356 0.060 0.114 1.06 L + 0.160 540 680 1450 1150

1/4 0.255 0.246 0.525 0.475 0.080 0.151 1.25 L + 0.180 1000 1240 2350 1950

Rivets

183



PART NUMBER COMPARISON - DOME HEAD STEEL RIVET/STEEL MANDREL

KanebridgeHuck-

Automatic Pop ® Marson/Creative Star Celus ® Cherry Gesipa ®

SDS41 SBS41 SD41BS SB4-1 4-1SSD S/S 41D SSP-41 GSMD41S








SDS53 SBS53 SD53BS SB5-3 5-3SSD S/S 53D - GSMD53

SDS54 SBS54 SD54BS SB5-4 5-4SSD S/S 54D SSP-54 GSMD54


SDS58 SBS58 - SB5-8 5-8SSD S/S 58D SSP-58 GSMD58





SDS610 SBS610 SD610BS SB6-10 6-10SSD S/S610D SSP-610 GSMD610

SDS84 SBS84 SD84BS SB8-4 - S/S 84D SSP-84 GSMD84



SDS810 SBS810 SD810BS - - S/S810D SSP-810 GSMD810

SDS812 SBS812 SD812BS SB8-12 - S/S812D SSP-812 GSMD812

SDS816 - SD816BS - - S/S816D SSP-816 GSMD816


Rivets

184

Aluminum/AluminumAluminum/Steel

Steel/Steel

Large FlangeBlind Rivet

LE

H

W D

P F‡

LARGE FLANGE BREAK-STEM BLIND RIVETS SAE J-1200

Nominal RivetDiameter

D H E W P F

Rivet Shank Diameter Head Diameter Head HeightMandrelDiameter

MandrelProtrusion


Max Min Max Min Max Nom Min Max

1/8 0.128 0.122 .390 .360 .065 0.076 1.00 L + 0.120

3/16 0.191 0.183 .650 .600 .092 0.114 1.06 L + 0.160

DescriptionA blind fastener which has a self-contained mandrel which permits the formation of an upset on the blind end of the rivet and expansionof the rivet shank during rivet setting to join the component parts of an assembly. The mandrel is pulled into or against the rivet body,

breaking at or near the junction of the mandrel shank and its upset end. The large flange head has twice the under-head bearingsurface of comparably sized dome head rivets.


Large flange rivets are preferred where extra brittle or soft materials are being assembled to a rigid surface.

MaterialRivet: Aluminum-- Aluminum Alloy 5050, 5052, 5056 or 5154. Steel-- Low carbon steel, plated zinc.

Mandrel: Aluminum-- Aluminum Alloy 7178, 5056 or 2024. Steel-- Carbon steel 1006 or equivalent. May be furnished plain or with aprotective coating, at the option of the manufacturer.

Shear Strength(Min)

Aluminum Rivet/Aluminum Mandrel-- 1/8: 120 lbs.; 3/16: 260 lbs.Aluminum Rivet/Steel Mandrel-- 1/8: 170 lbs.; 3/16: 380 lbs.

Steel Rivet/Steel Mandrel-- 3/16: 540 lbs.

Tensile Strength(Min)

Aluminum Rivet/Aluminum Mandrel-- 1/8: 150 lbs.; 3/16: 320 lbs.Aluminum Rivet/Steel Mandrel-- 1/8: 220 lbs.; 3/16: 500 lbs.

Steel Rivet/Steel Mandrel-- 3/16: 680 lbs.

Mandrel BreakLoad

Aluminum Rivet/Aluminum Mandrel-- 1/8: 400 lbs. max, 250 lbs. min; 3/16: 825 lbs. max, 625 lbs. min.Aluminum Rivet/Steel Mandrel-- 1/8: 600 lbs. max, 400 lbs. min; 3/16: 1050 lbs. max, 750 lbs. min.

Steel Rivet/Steel Mandrel-- 3/16: 1450 lbs. max, 1150 lbs. min.

Rivets

185

Large FlangeBlind Rivet

Aluminum/AluminumAluminum/Steel

Steel/Steel

PART NUMBER COMPARISON - LARGE FLANGE ALUMINUM RIVET/ALUMINUM MANDREL

KanebridgeHuck-


ADA44L ABA44L AD44ABSLF ABL4-4A 4-4AALF A/A44LF AAL-44 GAML44A

ADA64L ABA64L AD64ABSLF ABL6-4A - A/A64LF AAL-64 GAML64A




PART NUMBER COMPARISON - LARGE FLANGE ALUMINUM/STEEL MANDREL

KanebridgeHuck/


ADS46L - - - - A/S 46LF BSL-46 GSML46A

ADS48L - - - - - BSL-48 -

ADS64L ABS64L AD64BSLF ABL6-4 - A/S 64LF BSL-64 GSML64A

ADS66L ABS66L AD66BSLF ABL6-6 6-6ASLF A/S 66LF BSL-66 GSML66A

ADS68L ABS68L AD68BSLF ABL6-8 6-8ASLF A/S 68LF BSL-68 GSML68A

ADS610L ABS610L AD610BSLF ABL6-10 6-10ASLF A/S610LF BSL-610 GSML610A

PART NUMBER COMPARISON - LARGE FLANGE STEEL RIVET/STEEL MANDREL

KanebridgeHuck/


SDS64L SBS64L SD64BSLF SBL6-4 - S/S 64LF SSL-64 GSML64S

SDS66L SBS66L SD66BSLF SBL6-6 6-6SSLF S/S 66LF SSL-66 GSML66S

SDS68L SBS68L SD68BSLF SBL6-8 6-8SSLF S/S 68LF SSL-68 GSML68S

SDS610L SBS610L SD610BSLF SBL6-10 6-10SSLF S/S610LF SSL-610 GSML610S


Rivets

186

Closed-EndAluminum Rivet/Steel Mandrel


L

E

HD

(max)

Description An aluminum blind fastener with a self-contained steel mandrel whose mandrel head is completely protected and secured within theclosed end of the rivet. The head of the rivet body is slightly rounded and twice as wide as the body diameter.


Closed end rivets are used where the adjoining back-plate cannot be accessed but must be kept weatherproof. The installed rivetforms a tight seal preventing seepage of liquid or gas through the fastener assembly. They are preferred in many electronics

applications because there is no chance of mandrel pieces falling into the work area on the blind side. Closed-end rivets providegreater tensile and shear strength than similar-sized open end rivets. They should be used when fastening materials with

mechanical and physical properties similar to aluminum.

Material Rivet: Aluminum Alloy 5056 or equivalent alloy.Mandrel: Carbon steel 1006 or equivalent. May be furnished plain or with a protective coating, at the option of the manufacturer.




CLOSED-END, DOME HEAD ALUMINUM BODY/STEEL MANDREL BLIND RIVETS IFI

PartNumber

D

Hole Size DrillNumber

Grip Range

L H EUltimate

Shear Load

UltimateTensileLoad

Rivet BodyDiameter

LengthUnder Head

HeadDiameter

HeadHeight

Inches Max Nominal Max Min, lb. Min, lb.

ADSC62

.187(3/16)

.192 - .196 #11

.020 - .125 .406 .375 .080 500 690

ADSC64 .188 - .250 .531 .375 .080 500 690

ADSC66 .251 - .375 .656 .375 .080 500 690

ADSC68 .376 - .500 .781 .375 .080 500 690

ADSC84 .250 .257 - .261 F .126 - .250 .570 .500 .100 900 1100

PART NUMBER COMPARISON - CLOSED-END ALUMINUM RIVET/STEEL MANDREL

KanebridgeHuck/

AutomaticPop®

Marson/Creative

Star Celus® Cherry Gesipa®

ADSC62 - AD62H AB6-2CLD - A62D-CE - -





Rivets

187


Copper Rivet/Copper-plated Mandrel

LE

HW D

P F‡

PART NUMBER COMPARISON - DOME HEAD COPPER RIVET/COPPER-PLATED STEEL MANDREL


Pop® Marson/Creative


KDS42 CBS42 CD42BS CB4-2 - C/S 42D USP-42 -

KDS43 CBS43 - - - - USP-43 -

COPPER BODY/COPPER-PLATED STEEL MANDREL, DOME HEAD BREAK-STEM BLIND RIVETS SAE J-1200

NominalRivet

Diameter

D H E W P F

Mandrel Break LoadRivet Shank


HeadHeight

MandrelDiameter

MandrelProtrusion


Max Min Max Min Max Nom Min Max Max Min

1/8 0.128 0.122 0.262 0.238 0.040 0.076 1.00 L + 0.120 600 400

Description A copper blind fastener with a self-contained steel mandrel which is otherwise designed identically to an aluminum rivet with a steelmandrel. The head of the rivet body is slightly rounded and twice as wide as the body diameter.


Dome head is the only head style in which the copper rivet is offered. Copper rivets are not subject to tensile or shear strengthtesting, but meet the same mandrel break-load standards as aluminum rivets with steel mandrels. Copper is the most malleable of

the various rivet metals. It has a higher electrical conductivity than any of the other rivet metals which make it useful in manyelectrical applications. They should be used when fastening materials with mechanical and physical properties similar to copper.

Material Rivet: Copper Alloy No. 110.Mandrel: Carbon steel 1006 or equivalent, copper plated.

Shear Strength Copper rivets are not subject to shear testing (SAE J1200).

Tensile Strength Copper rivets are not subject to tensile testing (SAE J1200).

Mandrel BreakLoad While the rivet is being set, the axially applied load necessary to break the mandrel shall be within 600 lbs. max, and 400 lbs. min.


Rivets

188

Stainless Steel Rivet/Stainless Steel Mandrel


LE

HW D

P F

PART NUMBER COMPARISON - DOME HEAD ALL STAINLESS STEEL BLIND RIVETS

KanebridgeHuck/

AutomaticPop®

Marson/Creative


SSDSS42 FBF42 SSD42SSBS SSB4-2S 4-2STSTD SS/SS42D CCP-42 GSSMD42SS

SSDSS43 FBF43 SSD43SSBS SSB4-3S - SS/SS43D CCP-43 GSSMD43SSSSDSS44 FBF44 SSD44SSBS SSB4-4S 4-4STSTD SS/SS44D CCP-44 GSSMD44SS

SSDSS46 FBF46 SSD46SSBS SSB4-6S 4-6STSTD SS/SS46D CCP-46 GSSMD46SS

SSDSS48 FBF48 SSD48SSBS SSB4-8S - SS/SS48D - GSSMD48SS

SSDSS52 FBF52 SSD52SSBS SSB5-2S - SS/SS52D CCP-52 GSSMD52SS



SSDSS58 FBF58 - - - - - -





Description A stainless steel blind fastener with a self-contained stainless steel mandrel which is otherwise designed identically to other domehead rivets. The head of the body is slightly rounded and twice as wide as the diameter of the body.


Dome head is the only head style for stainless steel rivets. Stainless rivets have the strongest tensile strengths, shear strengthsand mandrel break-load standards of all the break mandrel rivets discussed in this section. They resist tarnishing under most

atmospheric conditions and offers high strength at moderately raised temperatures. They should be used when fastening materialswith mechanical and physical properties similar to stainless steel.

Material Rivet: 305 (or equivalent) Stainless SteelMandrel: Stainless Steel (300 series)



Mandrel BreakLoad



STAINLESS STEEL BODY/STAINLESS STEEL MANDREL DOME HEAD BREAK-STEM BLIND RIVETS SAE J-1200

NominalRivet

Diameter


UltimateTensileLoad

Mandrel BreakLoad, lb.Rivet Shank


HeadHeight

MandrelDiameter

MandrelProtrusion



3/32 0.096 0.090 0.198 0.178 0.032 0.057 1.00 L + 0.100 230 280 500 300

1/8 0.128 0.122 0.262 0.238 0.040 0.076 1.00 L + 0.120 420 530 950 650

5/32 0.159 0.153 0.328 0.296 0.050 0.095 1.06 L + 0.140 650 820 1450 1150

3/16 0.191 0.183 0.394 0.356 0.060 0.114 1.06 L + 0.160 950 1200 1900 1400

1/4 0.255 0.246 0.525 0.475 0.080 0.151 1.25 L + 0.180 1700 2100 3600 3000

Rivets

189

ApplicationData Part Number Key

Notes on Rivet SelectionStrength- The tensile and shear strengths required for an application must be determined and a rivet selected thatmeets those requirements.

Materials- Choose a rivet that is made of a metal with similar mechanical and physical properties as the materialsbeing joined. This is especially critical in assemblies where higher temperatures and/or corrosive elements are present.Metal compatability helps reduce the risks of galvanic corrosion and material fatigue.

Grip Range- Measure the total thickness of the materials being fastened. This is known as the “rivet grip”. The gripranges of the most commonly available rivets are listed in the table below. Sufficient rivet length is necessary forproper formation of the secondary head on the blind side of the assembly. Multi-grip rivets have wider grip rangesthan standard break-stem blind rivets.

ADS64L

Rivet Material: A = Aluminum; S = Steel; SS = Stainless; K = Copper

Mandrel Material: A = Aluminum; S = Steel; SS = Stainless

Grip Range: In 16ths of an inch (4/16 = 1/4)

L - This "L" indicates that the dome head is the Large Flange style.

Rivet Diameter: In 32nd's of an inch (6/32 = 3/16)

Head Style: D = Dome

*

*Kanebridge Part Number

APPLICATION DATA FOR STANDARD BREAK-STEM BLIND RIVETS SAE J-1200

RivetNumber

Grip Range

BarrelLength

RecommendedHole Size Drill Size

RivetNumber

Grip Range

BarrelLength

RecommendedHole Size Drill Size

Max Max Min Max Max Min

31 .020-.062 .187

0.100 0.097 #41

62 .020-.125 .325

0.196 0.192 #11

32 .020-.125 .250 63 .126-.187 .387

33 .087-.187 .312 64 .188-.250 .450

34 .126-.250 .375 66 .251-.375 .575

41 .020-.062 .212

0.133 0.129 #30

68 .376-.500 .700

42 .063-.125 .275 610 .510-.625 .825

43 .126-.187 .337 612 .626-.750 .950

44 .188-.250 .400 614 .751-.875 1.075

45 .251-.312 .462 616 .876-1.000 1.200

46 .313-.375 .525 618 1.001-1.125 1.325

48 .376-.500 .650 620 1.126-1.250 1.450

52 .020-.125 .300

0.164 0.160 #20

622 1.251-1.375 1.575

53 .125-.187 .362 84 .126-.250 .500

0.261 0.257 F

54 .188-.250 .425 86 .251-.375 .625

56 .251-.375 .550 88 .376-.500 .750

58 .376-.500 .675 810 .501-.625 .875

510 .501-.625 .800 812 .626-.750 .990

512 .626-.750 .925 816 .751-1.000 1.240

516 .876-1.000 1.175

Rivets

190

Multi-Grip Low-Profile Head Aluminum Blind Rivet/Steel Mandrel

B

ED

C A

DescriptionAn aluminum blind fastener with a self-contained steel mandrel. The multi-grip rivet design differs from a standard blind rivet two ways:(1) a section of the body shank has a slightly reduced outside diameter, and (2) the stem of the mandrel is pinched at a point above the

mandrel head. The head of the rivet body is lower and wider than a dome head (approximately twice the diameter of the shank).


Multi-grip rivets provide maximum clamping action over a full range of material thicknesses while using the same rivet length. Thisallows flexibility in design, cuts production costs and reduces inventories. Low-Profile heads are usually chosen to improve the

product's finished appearance. They should be used when fastening materials with mechanical and physical properties similar toaluminum.

Material Rivet: Aluminum Alloy 5251 or equivalent alloy.Mandrel: Low carbon steel with a choice of coating: black phosphate or zinc with yellow chromate.


Tensile Strength Rivets shall have ultimate tensile loads not less than the minimum ultimate tensile loads specified for the applicable size given in theabove table.

*Avdel Cherry Textron is the original writer of the multi-grip dimensions.

LOW-PROFILE MULTI-GRIP ALUMINUM BODY/STEEL MANDREL BLIND RIVETS Avdel*

PartNumber

A B C D E Recom-mendedHole Size

ShearStrength

TensileStrengthRivet

DiameterLength Head Diameter Head Height Grip

RangeMax Min Max Min Max Min Pounds Pounds

L-0410 1/8 .410 .350 .262 .243 .041 .034 .031-.187 .136 165 230

L-0412 1/8 .470 .420 .262 .243 .041 .034 .062-.250 .136 165 230L-0414 1/8 .530 .480 .262 .243 .041 .034 .125-.312 .136 165 230

L-0416 1/8 .590 .540 .262 .243 .041 .034 .187-.375 .136 165 230

L-0512 5/32 .480 .430 .321 .302 .051 .044 .046-.250 .166 255 375

L-0514 5/32 .540 .490 .321 .302 .051 .044 .125-.312 .166 255 375

L-0516 5/32 .610 .550 .321 .302 .051 .044 .156-.375 .166 255 375

L-0613 3/16 .550 .470 .396 .377 .061 .054 .062-.250 .199 350 530

L-0619 3/16 .730 .660 .396 .377 .061 .054 .187-.437 .199 350 530

L-0621 3/16 .780 .720 .396 .377 .061 .054 .250-.500 .199 350 530

L-0631 3/16 1.09 1.03 .396 .377 .061 .054 .500-.781 .199 350 530

PART NUMBER COMPARISON - LOW PROFILE HEAD MULTI-GRIP RIVETS

Kanebridge-Zinc yellow mandrel

Avdel Avex®-Zinc yellow mandrel

Kanebridge-Black phos mandrel

Avdel Avex® -Black phos mandrel

Pop® -Plain steel mandrel

L-0410Y 1691-0410 L-0410B 1661-0410 AD41-43BS

- 1691-0412 L-0412B 1661-0412 -

L-0414Y 1691-0414 L-0414B 1661-0414 AD43-45BS

L-0416Y 1691-0416 L-0416B 1661-0416 -

L-0512Y 1691-0512 L-0512B 1661-0512 AD52-54BS

L-0514Y 1691-0514 L-0514B 1661-0514 -

L-0516Y 1691-0516 - 1661-0516 -

L-0613Y 1691-0613 L-0613B 1661-0613 AD62-64BS

L-0619Y 1691-0619 L-0619B 1661-0619 AD63-66BS

L-0621Y 1691-0621 L-0621B 1661-0621 AD66-68BS

L-0631Y 1691-0631 L-0631B 1661-0631 -

®Pop is a registered trademark of Pop Fastening Systems, Emhart Fastening Teknologies, a Black & Decker Company.®Avex is a registered trademark of the Avdel Cherry Textron Corporation. Kanebridge’s rivets are not manufactured by or connected with the producers of Avex® or Pop® rivets.

Rivets

191

Aluminum Blind Rivet/Steel Mandrel Multi-Grip Dome Head

B

ED

CA

DescriptionAn aluminum blind fastener with a self-contained steel mandrel. The multi-grip rivet design differs from a standard blind rivet two

ways: (1) a section of the body shank has a slightly reduced outside diameter, and (2) the stem of the mandrel is pinched at a pointabove the mandrel head. The head of the rivet body is slightly rounded, similar to a pan head screw.


Multi-grip rivets provide maximum clamping action over a full range of material thicknesses while using the same rivet length. Thisallows flexibility in design, cuts production costs and reduces inventories. Dome heads are used in standard applications which call for

maximum clamp-up and hole fill. They should be used when fastening materials with mechanical and physical properties similar toaluminum.





DOME HEAD MULTI-GRIP ALUMINUM BODY/STEEL MANDREL BLIND RIVETS Avdel*

PartNumber

A B C D ERecom-mendedHole Size

ShearStrength

TensileStrength

RivetDiameter

Length Head Diameter Head Height GripRangeMax Min Max Min Max Min Pounds Pounds

D-0410 1/8 .410 .350 .217 .193 .045 .033 .031-.187 .136 165 230

D-0412 1/8 .470 .420 .217 .193 .045 .033 .062-.250 .136 165 230

D-0414 1/8 .530 .480 .217 .193 .045 .033 .125-.312 .136 165 230

D-0512 5/32 .480 .430 .257 .233 .058 .046 .046-.250 .166 255 375

D-0516 5/32 .610 .550 .257 .233 .058 .046 .156-.375 .166 255 375

D-0613 3/16 .550 .470 .351 .327 .071 .059 .062-.250 .199 350 530

D-0619 3/16 .730 .660 .351 .327 .071 .059 .187-.437 .199 350 530

D-0621 3/16 .780 .720 .351 .327 .071 .059 .250-.500 .199 350 530

D-0631 3/16 1.09 1.03 .351 .327 .071 .059 .500-.781 .199 350 530

PART NUMBER COMPARISON - DOME HEAD MULTI-GRIP RIVETS


Avdel Avex®Zinc yellow mandrel


Avdel Avex®Black phos mandrel

Pop® -Plain Steel mandrel

D-0410Y 1693-0410 D-0410B 1601-0410 -

D-0412Y 1693-0412 - 1601-0412 -

D-0414Y 1693-0414 D-0414B 1601-0414 -

D-0512Y 1693-0512 D-0512B 1601-0512 -

D-0516Y 1693-0516 D-0516B 1601-0516 -

D-0613Y 1693-0613 D-0613B 1601-0613 -

D-0619Y 1693-0619 D-0619B 1601-0619 -

D-0621Y 1693-0621 - 1601-0621 -

D-0631Y 1693-0631 D-0631B 1601-0631 -


Rivets

192

B

E D

CA

Multi-Grip Large Flange Aluminum Blind Rivet/Steel Mandrel


ways: (1) a section of the body shank has a slightly reduced outside diameter, and (2) the stem of the mandrel is pinched at a pointabove the mandrel head. The head of the large flange rivet is approximately 50% wider than the dome head.


Multi-grip rivets provide maximum clamping action over a full range of material thicknesses while using the same rivet length. Thisallows flexibility in design, cuts production costs and reduces inventories. The large flange style is preferred when the rivet is seated insoft material to prevent it from pulling through. They should be used when fastening materials with mechanical and physical properties

similar to aluminum.





LARGE FLANGE MULTI-GRIP ALUMINUM BODY/STEEL MANDREL BLIND RIVETS Avdel*

PartNumber


ShearStrength

TensileStrength

RivetDiameter


X-0410 1/8 .410 .350 .337 .313 .045 .033 .031-.187 .136 165 230

X-0414 1/8 .530 .480 .337 .313 .045 .033 .125-.312 .136 165 230

X-0514 5/32 .540 .490 .387 .363 .058 .046 .125-.312 .166 255 375

X-0516 5/32 .610 .550 .387 .363 .058 .046 .156-.375 .166 255 375

X-0521 5/32 .760 .715 .387 .363 .058 .046 .250-.500 .166 235 375

X-0613 3/16 .550 .470 .637 .613 .075 .063 .062-.250 .199 350 530

X-0621 3/16 .780 .720 .637 .613 .075 .063 .250-.500 .199 350 530

X-0631 3/16 1.09 1.03 .637 .613 .075 .063 .500-.781 .199 350 530

PART NUMBER COMPARISON - LARGE FLANGE MULTI-GRIP RIVETS


Avdel Avex® -Zinc yellow mandrel

Kanebridge -Black phos mandrel



X-0410Y 1692-0410 X-0410B 1641-0410 AD41-43BSLF

X-0414Y 1692-0414 X-0414B 1641-0414 -

X-0514Y 1692-0514 X-0514B 1641-0514 -

- 1692-0516 X-0516B 1641-0516 -

- 1692-0521 X-0521B 1641-0521 -

X-0613Y 1692-0613 X-0613B 1641-0613 AD62-64BSLF

X-0621Y 1692-0621 X-0621B 1641-0621 AD66-68BSLF

X-0631Y 1692-0631 X-0631B 1641-0631 -


Rivets

193

A

B

E

D

C

120o

Aluminum Blind Rivet/Steel Mandrel Multi-Grip Countersunk Head


ways: (1) a section of the body shank has a slightly reduced outside diameter, and (2) the stem of the mandrel is pinched at a pointabove the mandrel head. The rivet's head is countersunk at an angle of 120°.


Multi-grip rivets provide maximum clamping action over a full range of material thicknesses while using the same rivet length. Thisallows flexibility in design, cuts production costs and reduces inventories. The countersunk head style provides a smooth offside

surface and sufficient clearance for moving parts which pass over the rivet head. They should be used when fastening materials withmechanical and physical properties similar to aluminum.





COUNTERSUNK MULTI-GRIP ALUMINUM BODY/STEEL MANDREL BLIND RIVETS Avdel*

PartNumber


ShearStrength

TensileStrength

RivetDiameter


C-0412 1/8 .470 .410 .217 .198 .034 .026 .093-.250 .136 165 230

C-0414 1/8 .530 .480 .217 .198 .034 .026 .155-.312 .136 165 230

C-0416 1/8 .600 .530 .217 .198 .034 .026 .217-.375 .136 165 230

C-0514 5/32 .550 .490 .257 .238 .036 .028 .109-.312 .166 255 375

C-0615 3/16 .610 .520 .351 .343 .055 .047 .125-.312 .199 350 530

C-0621 3/16 .800 .710 .351 .343 .055 .047 .250-.500 .199 350 530

PART NUMBER COMPARISON - COUNTERSUNK MULTI-GRIP RIVETS


Avdel Avex® -Zinc yellow mandrel




C-0412Y 1682-0412 C-0412B 1604-0412 AK41-44BS

C-0414Y 1682-0414 C-0414B 1604-0414 -

C-0416Y 1682-0416 - 1604-0416 -

C-0514Y 1682-0514 - 1604-0514 -

C-0615Y 1682-0615 C-0615B 1604-0615 -

C-0621Y 1682-0621 C-0621B 1604-0621 -


Rivets

194

Multi-Grip: Dome,Countersunk & Large Flange


COUNTERSUNK HEAD DOME HEADLARGE FLANGE

DescriptionAn all steel blind fastener with a self-contained steel mandrel. The multi-grip rivet design differs from a standard blind rivet two ways:

(1) the body shank has several circumferential indents equidistant from each other, and (2) the stem of the mandrel is pinched at apoint above the mandrel head. Three head styles are available: dome, large flange and countersunk.


Multi-grip rivets provide maximum clamping action over a full range of material thicknesses while using the same rivet length. Thisallows flexibility in design, cuts production costs and reduces inventories. All steel multi grip rivets offer greater shear and tensile

strength than like-sized aluminum/steel multi grips and should be used when fastening materials with mechanical and physicalproperties similar to carbon steel. Dome heads are used in standard applications which call for maximum clamp-up and hole fill. Thelarge flange style is preferred when the rivet is seated in soft material. The countersunk head style provides a smooth offside surface

and sufficient clearance for moving parts which pass over the rivet head.

Material Rivet: Low carbon steelMandrel: Low carbon steel.

Shear Strength See above table for typical shear strength (assumes stem is in shear plane).

Tensile Strength See above table for typical shear strength.

L

G

H

D

B

120o

L

GH

DB

L

GH

DB

ALL STEEL MULTI-GRIP BLIND RIVETS Ornit

Head Style PartNumber

BDrill Size

L G D H Typical Strength (lbs.)

NominalRivet Diam.

Rivet BodyLength Grip Range Head Diam.

HeadHeight Shear Tensile

Countersunk

SF48110K

3/16" 11

.43 .098 - .236

.511 .067 992 860SF48140K .55 .118 - .354

SF48170K .67 .157 - .472

SF48220K .86 .354 - .670

LargeFlange

SF48110L

3/16" 11

.43 .039 - .236

.511 .067 992 860SF48140L .55 .039 - .354

SF48170L .67 .118 - .472

Dome

SF32090D1/8" 30

.35 .043 - .157.283 .033 340 385

SF32130D .51 .039 - .354

SF40110D 5/32" 20 .43 .055 - .197 .319 .047 440 530

SF48110D

3/16" 11

.43 .039 - .236

.386 .057 992 860SF48140D .55 .039 - .354

SF48170D .67 .118 - .472

Rivets

195

DOME HEAD ALL STEEL "US" M ULTI-GRIP BLIND RIVET Ornit

Part Number

A B C D ERecommended

Drill Size

ShearStrength

TensileStrength

RivetDiameter

Length Head Diameter Head HeightGrip Range

Ref Ref Ref Pounds Pounds

US32090LM 1/8 .354 .283 .034 .044 - .156 #30 340 385

US40110LM 5/32 .432 .319 .046 .056 - .196 #20 440 530

US48103LM 3/16 .405 .386 .069 .047 - .187 #11 810 750

US48127LM 3/16 .499 .386 .069 .156 - .250 #11 1025 780

DescriptionAn all steel blind fastener with a self-contained steel mandrel. The multi-grip rivet design differs from a standard blind rivet two ways:

(1) the body has a somewhat reduced diameter from the area under the head, extending about halfway down the shank, and (2) thestem of the mandrel is pinched at a point above the mandrel head. The head has a dome shape.


Multi-grip rivets provide maximum clamping action over a full range of material thicknesses while using the same rivet length. Thisallows flexibility in design, cuts production costs and reduces inventories. Steel multi grip rivets offer superior shear and tensilestrength than like-sized aluminum/steel multi grips and should be used when fastening materials with mechanical and physical

properties similar to carbon steel. Dome heads are used in standard applications which call for maximum clamp-up and hole fill.

Material Rivet: carbon steelMandrel: carbon steel.



Plating Both the rivet body and the mandrel are zinc coated.

Type “US” Multi-Grip: DomeSteel Rivet/Steel Mandrel

B

E

D

C

A

Rivets

196

DOME HEAD STAINLESS STEEL MULTI-GRIP BLIND RIVETS Ornit

PartNumber

A B C D ERecommended

Drill Size

ShearStrength

TensileStrength

RivetDiameter

Length Head Diameter Head HeightGrip Range

Ref Ref Ref Pounds Pounds

D-0612 3/16 .405 .386 .069 .059-.236 # 11 1441 1113

D-0616 3/16 .499 .386 .069 .098-.295 # 11 1441 1113

DescriptionAn all stainless steel blind fastener with a self-contained stainless steel mandrel. The multi-grip rivet design differs from a standardblind rivet two ways: (1) the body has a somewhat reduced diameter from the area under the head, extending approximately halfway

down the shank, and (2) the stem of the mandrel is pinched at a point above the mandrel head. The head has a dome shape.


Multi-grip rivets provide maximum clamping action over a full range of material thicknesses while using the same rivet length. Thisallows flexibility in design, cuts production costs and reduces inventories. Stainless steel multi grip rivets offer superior resistance to

corrosion than like-sized aluminum/steel multi grips and should be used when fastening materials with mechanical and physicalproperties similar to stainless steel. They are popular in food service equipment and boats. Dome heads are used in standard

applications which call for maximum clamp-up and hole fill.

Material Rivet: ALSI 304 stainless steelMandrel: ALSI 434 stainless steel.



B

E

D

C

A

Multi-Grip: Dome Stainless Rivet/Stainless Mandrel

Rivets

197

3-Star Bulbing StyleAll Aluminum/Dome Head

DescriptionAn aluminum blind fastener with a self-contained aluminum mandrel. The body of the rivet has three longitudinal slits extending from

directly beneath the dome-shaped rivet head, down the shank but not completely to thehead of the mandrel. The bottom portion of theshank is not slit and has a slightly smaller body diameter where the rivet is snug against the mandrel within it.


When the rivet is installed, the body disrupts on the blind side in a way that forms three petals which extend away from the mandrelhead. This makes this rivet ideal in out-of-round or oversized holes. The rivet requires less pulling force during installation than does astandard blind rivet which makes it useful in thin, soft or brittle materials. Each size has a relatively wide grip range and is corrosion

resistant.

Material Rivet: AluminumMandrel: Aluminum

Shear Strength Typical shear strengths are listed in the above table.

Tensile Strength Typical tensile strengths are listed in the above table.

L

G H

DBW

M

3-STAR BULBING TYPE BLIND RIVET - ALUMINUM Ornit

B

Part Number

L D H W M

RecommendedHole Size

GTypical Strength

(lbs.)

NominalRivet

Diameter

ShankLength

HeadDiameter

HeadHeight

MandrelWidth

MandrelProtrusion

Grip Range Shear Tensile

5/3201600004013 .535

.315 .055 .094 1.18 .165 - .177.039 - .118

112 22501600004018 .740 .039 - .275

3/16

01600004815 .602

.346 .063 .114 1.18 .197 - .209

.039 - .118

202 24701600004820 .807 .039 - .354

01600004824 .965 .157 - .472

Rivets

198

Drive Pin BrazierHead

L

R

H

D

Description

A two-piece fastening system consisting of (1) a self-contained pin within (2) the body of a tubular-shaped rivet with a dome-shapedhead. The head is approximately 2-1/2 times as wide as the shank diameter. The top of the rivet has an opening through which the pin

protrudes. The opposite end of the rivet is enclosed but with two cross-wise slits cut into the body extending from the tip, up the shank alimited distance.


Drive pin rivets can join two or more pieces of low-density metal without the use of special installation tools. The rivet is inserted intopre-drilled, aligned holes and is set in place by striking the top of the pin with a hammer so that the pin is flush with the top of the head.

This action causes the pin to drive through the opposite end and flare out in four directions creating a head on the blind side of thefastening. Drive pins have superior shear strength to standard break stem rivets because the pin remains inside of the installed rivet forits entire length. The brazier head variety offers a greater bearing surface area than the universal head. The rivets with a grip range of an

inch or greater may be used for fastening into masonry.

Material Body: Aluminum alloy 2117 H15 or equivalent alloyPin: Aluminum alloy 2024 T4 or equivalent alloy

Shear Strength(approximate)

3/16" diameter: 650 psi. minimum; 1/4" diameter: 1150 psi. minimum

Tensile Strength(approximate) 3/16" diameter: 460 psi. minimum; 1/4" diameter: 820 psi. minimum

BRAZIER HEAD DRIVE PIN RIVETS

PartNumber

D LGrip Range

R H

PartNumber

D LGrip Range

R H

ShankDiameter(± .001)

Length(+.010,-.005)

HeadDiameter

(+.005,-.015)

HeadHeight

(± .005)


Length(+.010,-.005)

HeadDiameter

(+.005,-.015)

HeadHeight(± .005)Min Max Min Max

05094ABSS .125 .187 .078 .109 .312 .062 14250ABA

.250

.406 .203 .297

.625 .125

The above item has a Stainless Steel pin. 14313ABA .469 .266 .359

10094ABA

.187

.250 .047 .141

.469 .094

14375ABA .531 .328 .422

10125ABA .281 .078 .172 14438ABA .594 .391 .484

10188ABA .344 .141 .234 14500ABA .656 .453 .547

10250ABA .406 .203 .297 14563ABA .719 .516 .609

10313ABA .469 .266 .359 14625ABA .781 .578 .672

10375ABA .531 .328 .422 14688ABA .844 .641 .734

10438ABA .594 .391 .484 14750ABA .906 .703 .797

10500ABA .656 .453 .547 14813ABA .969 .766 .859

10563ABA .719 .516 .609 14875ABA 1.031 .828 .922

10625ABA .781 .578 .672 14938ABA 1.094 .891 .984

10750ABA .906 .703 .797 141000ABA 1.156 .953 1.047

10813ABA .969 .766 .859 141125ABA 1.281 1.078 1.172

10875ABA 1.031 .828 .922 141188ABA 1.344 1.141 1.234

10938ABA 1.094 .891 .984 141250ABA 1.406 1.203 1.297

101000ABA 1.156 .953 1.047 141313ABA 1.469 1.266 1.359

14094ABA

.250

.250 .047 .141

.625 .125

141375ABA 1.531 1.328 1.422

14125ABA .281 .078 .172 141438ABA 1.594 1.484 1.572

14188ABA .344 .141 .234

Rivets

199

Drive Pin

Description

A two-piece fastening system consisting of (1) a self-contained pin within (2) the body of a tubular-shaped rivet with a flat, countersunkhead. The head is countersunk at an angle of 100° and is a little less than twice the diameter of the shank. The top of the rivet has an

opening through which the pin protrudes. The opposite end of the rivet is enclosed but with two cross-wise slits cut into the body extendingfrom the tip, up the shank a limited distance.


Drive pin rivets can join two or more pieces of low-density metal without the use of special installation tools. The rivet is inserted into pre-drilled, aligned holes and is set in place by striking the top of the pin with a hammer so that the pin is flush with the top of the head. Thisaction causes the pin to drive through the opposite end and flare out in four directions creating a head on the blind side of the fastening.

Drive pins have superior shear strength to standard break stem rivets because the pin remains inside of the installed rivet for its entirelength. The flat head style provides a smooth offside surface with sufficient clearance for moving parts that pass over the rivet head.




TensileStrength

(approximate)3/16" diameter: 460 psi. minimum; 1/4" diameter: 820 psi. minimum

L

R

D

H

CountersunkHead

COUNTERSUNK DRIVE PIN RIVETS

PartNumber

D LGrip Range

R H

Part Number

D LGrip Range

R H


Length(+.010,-.005)

HeadDiameter

(+.005,-.015)

HeadHeight(± .005)


Length(+.010,-.005)

HeadDiameter

(+.005,-.015)


10188ACA

.188

.344 .141 .234

.344 .070

14375ACA

.250

.531 .328 .422

.467 .095

10250ACA .406 .203 .297 14438ACA .594 .391 .484

10313ACA .469 .266 .359 14500ACA .656 .453 .547

10375ACA .531 .328 .422 14563ACA .719 .516 .609

10438ACA .594 .391 .484 14625ACA .781 .578 .672

10500ACA .656 .453 .547 14688ACA .844 .641 .734

10563ACA .719 .516 .609 14750ACA .906 .703 .797

10625ACA .781 .578 .672 14813ACA .969 .766 .859

14188ACA

.250

.344 .141 .234

.467 .095

14875ACA 1.031 .828 .922

14250ACA .406 .203 .297 14938ACA 1.094 .891 .984

14313ACA .469 .266 .359 141000ACA 1.156 .953 1.047

Rivets

200

Drive Pin LinerHead

Description

A two-piece fastening system consisting of (1) a self-contained pin within (2) the body of a tubular-shaped rivet with a wide, trapezoidal-shaped head. The head has a very low profile and is approximately three times the diameter of the shank. The top of the rivet has an openingthrough which the pin protrudes. The opposite end of the rivet is enclosed but with two cross-wise slits cut into the body extending from the

tip, up the shank a limited distance.


Drive pin rivets can join two or more pieces of low-density metal without the use of special installation tools. The rivet is inserted into pre-drilled, aligned holes and is set in place by striking the top of the pin with a hammer so that the pin is flush with the top of the head. Thisaction causes the pin to drive through the opposite end and flare out in four directions creating a head on the blind side of the fastening.

Drive pins have superior shear strength to standard break stem rivets because the pin remains inside of the installed rivet for its entirelength. The liner head variety is designed specifically to be used to attach plywood or plastic liners in truck trailers.




TensileStrength

(approximate)3/16" diameter: 460 psi. minimum; 1/4" diameter: 820 psi. minimum

L

R

H

D

LINER HEAD DRIVE PIN RIVETS - ALL ALUMINUM

PartNumber

D LGrip Range

R H

PartNumber

D LGrip Range

R H


Length(+.010,-.005)

HeadDiameter

(+.005,-.010)

HeadHeight(± .005)


Length(+.010,-.005)

HeadDiameter

(+.005,-.010)

HeadHeight

(± .005)Min Max Min Max

10125ALA

.187

.281 .075 .175

.609 .085

10625ALA

.187

.781 .575 .675

.609 .08510219ALA .391 .175 .275 10750ALA .875 .675 .775

10312ALA .484 .275 .375 10813ALA .984 .775 .875

10406ALA .578 .375 .475 10938ALA 1.078 .875 .975

10500ALA .688 .475 .575

Rivets

201

UniversalHead

L

R

HD

Drive Pin

UNIVERSAL HEAD DRIVE PIN RIVETS

PartNumber

D LGrip Range

R H

PartNumber

D LGrip Range

R H


Length(+.010,-.005)

HeadDiameter

(+.005,-.015)

HeadHeight

(± .005)


Length(+.010,-.005)

HeadDiameter

(+.005,-.015)


05031AUSS

.125

.156 .015 .046

.250 .054

14094AUA

.250

.250 .047 .141

.500 .107

05063AUSS .156 .046 .078 14125AUA .281 .078 .172

05094AUSS .188 .078 .109 14188AUA .344 .141 .234

05438AUSS .531 .422 .453 14250AUA .406 .203 .297

07031AUSS

.156

.188 .015 .046

.312 .067

14313AUA .469 .266 .359

07063AUSS .188 .046 .078 14375AUA .531 .328 .422

07094AUSS .219 .078 .109 14438AUA .594 .391 .484

07438AUSS .563 .422 .453 14500AUA .656 .453 .547

07500AUSS .625 .484 .515 14563AUA .719 .516 .609

07531AUSS .656 .515 .546 14625AUA .781 .578 .672

07563AUSS .688 .546 .578 14688AUA .844 .641 .734

07625AUSS .750 .609 .640 14750AUA .906 .703 .797

10094AUA

.187

.250 .047 .141

.375 .080

14813AUA .969 .766 .859

10125AUA .281 .078 .172 14875AUA 1.031 .828 .922

10188AUA .344 .141 .234 14938AUA 1.094 .891 .984

10250AUA .406 .203 .297 141000AUA 1.156 .953 1.047

10313AUA .469 .266 .359 141125AUA 1.281 1.078 1.172

10375AUA .531 .328 .422 141375AUA 1.531 1.328 1.422

10438AUA .594 .391 .484 31188AUA

.313

.438 .132 .242

.625 .138

10500AUA .656 .453 .547 31281AUA .531 .226 .336

10563AUA .719 .516 .609 31375AUA .625 .320 .430

10625AUA .781 .578 .672 31469AUA .719 .414 .523

10688AUA .844 .641 .734 31563AUA .813 .508 .617

10750AUA .906 .703 .797 37188AUA

.375

.500 .125 .250

.750 .166

10813AUA .969 .766 .859 37281AUA .594 .219 .344

10875AUA 1.031 .828 .922 37375AUA .688 .313 .438

101000AUA 1.156 .953 1.047 37469AUA .781 .406 .531

101125AUA 1.281 1.078 1.172 37563AUA .875 .500 .625

DescriptionA two-piece fastening system consisting of (1) a self-contained pin within (2) the body of a tubular-shaped rivet with a dome-shaped head. Thehead is approximately twice as wide as the shank diameter. The top of the rivet has an opening through which the pin protrudes. The opposite

end of the rivet is enclosed but with two cross-wise slits cut into the body extending from the tip, up the shank a limited distance.


Drive pin rivets can join two or more pieces of low-density metal without the use of special installation tools. The rivet is inserted into pre-drilled, aligned holes and is set in place by striking the top of the pin with a hammer so that the pin is flush with the top of the head. This

action causes the pin to drive through the opposite end and flare out in four directions creating a head on the blind side of the fastening. Drivepins have superior shear strength to standard break stem rivets because the pin remains inside of the installed rivet for its entire length. The

universal head is the most versatile variety of drive pin, giving the neat, finished look of the brazier but with a lower head profile.

MaterialAluminum Steel

Body: Aluminum alloy 2117 H15 or equivalent alloyPin: Aluminum alloy 2024 T4 or equivalent alloy

Body: AISI 1006 - 1008 or equivalent steel, zinc-platedPin: AISI 1008 or equivalent steel, zinc-plated

Rivets

202

Semi-tubular Rivets Oval Heads

SEMI-TUBULAR OVAL HEAD RIVETS ANSI/ASME B18.7

NominalSize

B D H E K T J P Tolerance on Lengths

ShankDiameter

HeadDiameter

HeadThickness

Type T Taper Hole RivetsType S

Straight Hole RivetsUp toand

including4 timesshank

dia.

Over 4 timesshank dia.and up to

andincluding 8times shank

dia.

Over 8timesshank

dia.

Hole Dia. atEnd of Rivet

HoleDia. atBottomof Hole

HoleDepth

to Startof

Apex


HoleDepth

to Startof

Apex

Max Min Max Min Max Min Max Min Min Min Max Min Nom

0.061 0.061 0.058 0.114 0.104 0.019 0.015 0.046 0.042 0.032 0.042 0.044 0.039 0.046 ±0.007 ±0.008 ±0.010

0.089 0.089 0.085 0.152 0.142 0.026 0.020 0.068 0.064 0.050 0.057 0.068 0.062 0.064 ±0.007 ±0.008 ±0.010

0.099 0.099 0.095 0.192 0.182 0.032 0.026 0.076 0.072 0.057 0.065 0.076 0.070 0.077 ±0.007 ±0.008 ±0.010

0.123 0.123 0.118 0.223 0.213 0.038 0.030 0.095 0.091 0.079 0.082 0.090 0.084 0.094 ±0.007 ±0.010 ±0.015

0.146 0.146 0.141 0.239 0.229 0.045 0.035 0.112 0.106 0.085 0.104 0.107 0.100 0.126 ±0.010 ±0.012 ±0.015

0.188 0.188 0.182 0.318 0.306 0.065 0.055 0.145 0.139 0.110 0.135 0.141 0.134 0.155 ±0.010 ±0.012 ±0.015

0.217 0.217 0.210 0.444 0.430 0.076 0.061 0.166 0.158 0.136 0.151 0.163 0.155 0.189 ±0.010 ±0.015 ±0.020

0.252 0.252 0.244 0.507 0.493 0.085 0.071 0.191 0.181 0.150 0.183 0.184 0.176 0.219 ±0.010 ±0.015 ±0.020

0.310 0.310 0.302 0.570 0.554 0.100 0.086 0.235 0.225 0.190 0.214 0.219 0.211 0.243 ±0.010 ±0.015 ±0.020

Type S

P

L

BJ

Type T

T

L

BK

H

E

D

H

D

Description A small, headed metal fastener having a coaxial cylindrical or tapered hole which does not exceed 112% of the mean shank diameter inthe end opposite a slightly rounded head. The head is approximately 50% wider than the diameter of the rivet body.


Easier to clinch than solid rivets. The hole reduces riveting forces for riveting tooling while the remaining clinched solid shank can providecomparable shear strengths to other common riveting products. The oval head style is popular because of its low profile head and neat,

finished appearance. The fastener is installed with a riveting hammer.

MaterialSteel: Low carbon steel (containing 0.1% carbon or less)

Aluminum: Grades 5056, 1100, 2017, 2117 or 6053

Rivets

203

Truss Heads Semi-tubular Rivets

TRUSS HEAD SEMI-TUBULAR RIVETS ANSI/ASME B18.7

NominalSize

B D H E K T J P Tolerance on Length

ShankDiameter

HeadDiameter

HeadThickness

Type T Taper Hole RivetsType S

Straight Hole Rivets Up toand


dia.


andincluding 8

times shankdia.

Over 8timesshank

dia.


HoleDia. at

Bottomof Hole

HoleDepth

to Startof Apex


HoleDepth

to Startof

Apex

Max Min Max Min Max Min Max Min Min Min Max Min Nom

0.061 0.061 0.058 0.130 0.120 0.019 0.015 0.046 0.042 0.032 0.042 0.044 0.039 0.046 ±0.007 ±0.008 ±0.010

0.089 0.089 0.085 0.192 0.182 0.026 0.020 0.068 0.064 0.050 0.057 0.068 0.062 0.064 ±0.007 ±0.008 ±0.010

0.123 0.123 0.118 0.286 0.276 0.038 0.030 0.095 0.091 0.079 0.082 0.090 0.084 0.094 ±0.007 ±0.010 ±0.015

0.146 0.146 0.141 0.318 0.306 0.045 0.035 0.112 0.106 0.085 0.104 0.107 0.100 0.126 ±0.010 ±0.012 ±0.015

0.188 0.188 0.182 0.381 0.369 0.065 0.055 0.145 0.139 0.110 0.135 0.141 0.134 0.155 ±0.010 ±0.012 ±0.015

Type S

P

L

BJ

Type T

T

L

BK

H

E

D

H

D

Description A small, headed metal fastener having a coaxial cylindrical or tapered hole which does not exceed 112% of the mean shank diameter inthe end opposite the head. The head is approximately twice the diameter of the rivet body.


Easier to clinch than solid rivets. The hole reduces riveting forces for riveting tooling while the remaining clinched solid shank can providecomparable shear strengths to other common riveting products. The truss head style is chosen when the rivet is seated in soft material

to prevent it from pulling through. The fastener is installed with a riveting hammer.



Rivets

204

Semi-tubular Rivets 120° CountersunkFlat Head

Type S

P

L

BJ

H

120±1

o

o

Type T

T

L

BK

H

120±1

o

o

E

D D

SEMI-TUBULAR RIVETS, 120° COUNTERSUNK HEAD ANSI/ASME B18.7

NominalSize

B D H E K T J P Tolerance on Length

ShankDiameter

Head DiameterHeadThick-ness

Type T Taper Hole Rivets Type S Straight HoleRivets Up to and


dia.


and including8 times

shank dia.

Over 8timesshank

dia.Max,EdgeSharp

Min,EdgeRoun-ded or

Flat


HoleDia. at

Bottomof Hole

HoleDepth

to Startof Apex


HoleDepth

to Startof Apex

Max Min Ref Max Min Min Min Max Min Nom

0.089 0.089 0.085 0.223 0.203 0.039 0.068 0.064 0.050 0.057 0.068 0.062 0.064 ±0.007 ±0.008 ±0.010

0.123 0.123 0.118 0.271 0.245 0.043 0.095 0.091 0.079 0.082 0.090 0.084 0.094 ±0.007 ±0.010 ±0.015

0.146 0.146 0.141 0.337 0.307 0.056 0.112 0.106 0.085 0.104 0.107 0.100 0.126 ±0.010 ±0.012 ±0.015

0.188 0.188 0.182 0.404 0.369 0.063 0.145 0.139 0.110 0.135 0.141 0.134 0.155 ±0.010 ±0.012 ±0.015

0.217 0.217 0.210 0.472 0.430 0.075 0.166 0.158 0.136 0.151 0.163 0.155 0.189 ±0.010 ±0.015 ±0.020

0.252 0.252 0.244 0.540 0.493 0.084 0.191 0.181 0.150 0.183 0.184 0.176 0.219 ±0.010 ±0.015 ±0.020

Description A small, headed metal fastener having a coaxial cylindrical or tapered hole which does not exceed 112% of the mean shank diameter inthe end opposite the head. The rivet's head is countersunk at an angle of 120°.


Easier to clinch than solid rivets. The hole reduces riveting forces for riveting tooling while the remaining clinched solid shank can providecomparable shear strengths to other common riveting products. The 120° countersunk head provides a smooth offside surface and

sufficient clearance for moving parts which pass over the rivet head. The fastener is installed with a riveting hammer.



Rivets

205

150° CountersunkFlat Head Semi-tubular Rivets

P

L

BJ

H

150±2

o

o

136 Approx.o

D

SEMI-TUBULAR RIVETS, 150° COUNTERSUNK HEAD ANSI/ASME B18.7

NominalSize

B D H J P Tolerance on Length

ShankDiameter

Head Diameter Head ThicknessHole Dia. atEnd of Rivet

HoleDepth

to Startof Apex

Up toand


dia.


andincluding 8

times shankdia.

Over 8timesshank

dia.Standard

HeadLarge Head Standard

HeadLarge Head

Max Min Max Min Max Min Max Min Max Min Max Min Ref

0.146 0.146 0.141 0.303 0.289 0.367 0.351 0.045 0.035 0.051 0.041 0.105 0.099 0.141 ±0.010 0.012 0.015

0.188 0.188 0.182 0.367 0.351 0.478 0.458 0.051 0.041 0.067 0.053 0.139 0.133 0.188 ±0.010 ±0.012 ±0.015

0.252 0.252 0.244 0.478 0.458 .... .... 0.067 0.053 .... .... 0.183 0.173 0.250 ±0.010 ±0.015 ±0.020

DescriptionA small, headed metal fastener having a coaxial cylindrical or tapered hole which does not exceed 112% of the mean shank diameter inthe end opposite the head. The rivet's head is countersunk at an angle of 150° and has a low-profile that protrudes slightly above the

material to which the rivet is attached.


Easier to clinch than solid rivets. The hole reduces riveting forces for riveting tooling while the remaining clinched solid shank can providecomparable shear strengths to other common riveting products. The 150° countersunk head is often chosen for decorative purposes.

The fastener is installed with a riveting hammer.



Rivets

206

Solid Rivets ButtonHead

H

L

D PR

SOLID BUTTON HEAD RIVETSANSI/ASME

B18.1.1

Nominal Size or BasicShank Diameter

P D H R

Shank Diameter Head Diameter Head Height Head Radius

Max Min Max Min Max Min Approx

1/16 0.062 0.064 0.059 0.122 0.102 0.052 0.042 0.055

3/32 0.094 0.096 0.090 0.182 0.162 0.077 0.065 0.084

1/8 0.125 0.127 0.121 0.235 0.215 0.100 0.088 0.111

5/32 0.156 0.158 0.152 0.290 0.268 0.124 0.110 0.138

3/16 0.188 0.191 0.182 0.348 0.322 0.147 0.133 0.166

7/32 0.219 0.222 0.213 0.405 0.379 0.172 0.158 0.195

1/4 0.250 0.253 0.244 0.460 0.430 0.196 0.180 0.221

9/32 0.281 0.285 0.273 0.518 0.484 0.220 0.202 0.249

5/16 0.312 0.316 0.304 0.572 0.538 0.243 0.225 0.276

11/32 0.344 0.348 0.336 0.630 0.592 0.267 0.247 0.304

3/8 0.375 0.380 0.365 0.684 0.646 0.291 0.271 0.332

13/32 0.406 0.411 0.396 0.743 0.699 0.316 0.294 0.358

7/16 0.438 0.443 0.428 0.798 0.754 0.339 0.317 0.387

Tolerance on LengthPlus Minus

0.016 0.016

STANDARD HEADER POINTS FOR SMALL SOLID RIVETS* ANSI/ASME B18.1.1

Nominal Size or Basic Shank Diameter

S TNominal Shank Length

Point Diameter Point Length

Approx Approx Max

3/32 0.094 0.077 0.023 3/4

1/8 0.125 0.102 0.031 3/4

5/32 0.156 0.127 0.039 1

3/16 0.188 0.154 0.047 1

7/32 0.219 0.179 0.055 1-3/8

1/4 0.250 0.204 0.062 1-3/8

9/32 0.281 0.230 0.070 1-1/2

5/16 0.312 0.255 0.078 1-1/2

11/32 0.344 0.281 0.086 1-5/8

3/8 0.375 0.307 0.094 1-5/8

7/16 0.438 0.358 0.110 3

*Apply when pointed rivets are specified.

S

T

40 Approx0

Rivets

207

PanHead Solid Rivets

H

L

D P

R2

R1

R3

SOLID PAN HEAD RIVETSANSI/ASME

B18.1.1

Nominal Size or BasicShank Diameter

P D H R1 R2 R3

Shank Dianeter Head Diameter Head HeightHead

CornerRadius

HeadSide

Radius

HeadCrownRadius

Max Min Max Min Max Min Approx Approx Approx

1/16 0.062 0.064 0.059 0.118 0.098 0.040 0.030 0.019 0.052 0.217

3/32 0.094 0.096 0.090 0.173 0.153 0.060 0.048 0.030 0.080 0.326

1/8 0.125 0.127 0.121 0.225 0.205 0.078 0.066 0.039 0.106 0.429

5/32 0.156 0.158 0.152 0.279 0.257 0.096 0.082 0.049 0.133 0.535

3/16 0.188 0.191 0.182 0.334 0.308 0.114 0.100 0.059 0.159 0.641

7/32 0.219 0.222 0.213 0.391 0.365 0.133 0.119 0.069 0.186 0.754

1/4 0.250 0.253 0.244 0.444 0.414 0.151 0.135 0.079 0.213 0.858

9/32 0.281 0.285 0.273 0.499 0.465 0.170 0.152 0.088 0.239 0.963

5/16 0.312 0.316 0.304 0.552 0.518 0.187 0.169 0.098 0.266 1.070

11/32 0.344 0.348 0.336 0.608 0.570 0.206 0.186 0.108 0.292 1.176

3/8 0.375 0.380 0.365 0.663 0.625 0.225 0.205 0.118 0.319 1.286

13/32 0.406 0.411 0.396 0.719 0.675 0.243 0.221 0.127 0.345 1.392

7/16 0.438 0.443 0.428 0.772 0.728 0.261 0.239 0.137 0.372 1.500


0.016 0.016

Description A small, pan-head metal fastener having no internal cavity, made of a malleable material.

Applications/Advantages Designed to permanently join two or more pieces of metal with pre-drilled holes.

Material Grade 0 solid rivets shall be made from steel which conforms to the following chemical composition ladle analysis:Phosphorous: 0.040% maximum; Sulfur: 0.050% maximum

Hardness Rockwell B 65 maximum

Tensile Strength 40,000 - 55,000 psi.

Yield Point 23,000 psi., minimum

Elongation in 8 in. 27%, minimum

Rivets

208

Solid Rivets FlatHead

H

L

D P

SOLID RIVETS, FLAT HEADANSI/ASME

B18.1.1

Nominal Size or Basic ShankDiameter

P D H

Shank Diameter Head Diameter Head Height

Max Min Max Min Max Min

1/16 0.062 0.064 0.059 0.140 0.120 0.027 0.017

3/32 0.094 0.096 0.090 0.200 0.180 0.038 0.026

1/8 0.125 0.127 0.121 0.260 0.240 0.048 0.036

5/32 0.156 0.158 0.152 0.323 0.301 0.059 0.045

3/16 0.188 0.191 0.182 0.387 0.361 0.069 0.055

7/32 0.219 0.222 0.213 0.453 0.427 0.080 0.065

1/4 0.250 0.253 0.244 0.515 0.485 0.091 0.075

9/32 0.281 0.285 0.273 0.579 0.545 0.103 0.085

5/16 0.312 0.316 0.304 0.641 0.607 0.113 0.095

11/32 0.344 0.348 0.336 0.705 0.667 0.124 0.104

3/8 0.375 0.380 0.365 0.769 0.731 0.135 0.115

13/32 0.406 0.411 0.396 0.834 0.790 0.146 0.124

7/16 0.438 0.443 0.428 0.896 0.852 0.157 0.135


0.016 0.016

Description A small, flat-head metal fastener having no internal cavity, made of a malleable material.


Designed to permanently join two or more pieces of metal with pre-drilled holes. Flat head design is sometimes preferred over the panhead to improve the product's finished appearance.






Rivets

209

Flat CountersunkHead Solid Rivets

H

L

P90 ± 2o o

D

SOLID RIVETS, FLAT COUNTERSUNK HEADANSI/ASME

B18.1.1

Nominal Size or Basic ShankDiameter

P D H

Shank Diameter Head Diameter Head Height

Max Min Max Min Ref

1/16 0.062 0.064 0.059 0.118 0.110 0.027

3/32 0.094 0.096 0.090 0.176 0.163 0.040

1/8 0.125 0.127 0.121 0.235 0.217 0.053

5/32 0.156 0.158 0.152 0.293 0.272 0.066

3/16 0.188 0.191 0.182 0.351 0.326 0.079

7/32 0.219 0.222 0.213 0.413 0.384 0.094

1/4 0.250 0.253 0.244 0.469 0.437 0.106

9/32 0.281 0.285 0.273 0.528 0.491 0.119

5/16 0.312 0.316 0.304 0.588 0.547 0.133

11/32 0.344 0.348 0.336 0.646 0.602 0.146

3/8 0.375 0.380 0.365 0.704 0.656 0.159

13/32 0.406 0.411 0.396 0.763 0.710 0.172

7/16 0.438 0.443 0.428 0.823 0.765 0.186


0.016 0.016

Description A small, countersunk, flat-head metal fastener having no internal cavity, made of a malleable material.


Designed to permanently join two or more pieces of metal with pre-drilled holes. Countersunk head design is preferred when movingparts must pass over the fastened area.






Rivets

210

Split Rivets Oval Head

LHDE

RG

SPLIT RIVETS, OVAL HEADANSI/ASME

B18.7

NominalSize

E D H G R

Tolerance onLengthShank Diameter Head Diameter Head Thickness

Radius ofHead

FilletRadius

Max Min Max Min Max Min Approx Max

0.092 0.092 0.085 0.152 0.142 0.026 0.020 0.22 0.012 ±0.010

0.125 0.125 0.113 0.223 0.213 0.035 0.027 0.31 0.016 ±0.015

0.152 0.152 0.144 0.318 0.306 0.045 0.035 0.27 0.020 ±0.015

0.190 0.190 0.180 0.349 0.337 0.055 0.045 0.25 0.025 ±0.015

Description A small, round headed metal fastener with a split end for clinching by spreading the ends.


Designed to permanently join soft materials such as rubber, leather, canvas, wood and soft plastics. It eliminates cost of pre-drillingholes while preserving the strength of the assembly by not having material removed from the objects being joined. The rivet is installed

with anvils that spread the prongs against the material.

Material Steel: Low carbon steel (containing 0.1% carbon or less)

Rivets

211

LH

DE

SPLIT RIVETS, FLAT COUNTERSUNK HEAD ANSI/ASME B18.7

Nominal Size

E D HTolerance on

LengthShank Diameter Head Diameter Head Thickness

Max Min Max Min Max Min

0.125 0.125 0.113 0.223 0.213 0.036 0.026 ±0.015

0.152 0.152 0.144 0.317 0.307 0.053 0.043 ±0.015

0.152 0.152 0.144 0.380* 0.370* 0.062* 0.052* ±0.015

0.190 0.190 180 0.443 0.431 0.061 0.051 ±0.015

*Rivets in 0.152 in., size having these head proportions shall be designated "Large Flat Countersunk Head."

Split RivetsFlat, Counter-sunk Head

Description A small, countersunk head metal fastener with a split end for clinching by spreading the ends.


Designed to permanently join soft materials such as rubber, leather, canvas, wood and soft plastics. It eliminates cost of pre-drillingholes while preserving the strength of the assembly by not having material removed from the objects being joined. The rivet is installed

with anvils that spread the prongs against the material.

Material Steel: Low carbon steel (containing 0.1% carbon or less)

Rivets

212

Full-tubular Rivets Oval, Truss & FlatCountersunk Heads

H L

D

ROval Head

H L

D

RTruss Head

HL

D

Flat Countersunk Head

P

L

SJ

L

SJ

Extruded or drilled to head

FULL-TUBULAR RIVETS ANSI/ASME B18.7

HeadStyle

NominalSize

S D H J P R Tolerance on Length

ShankDiameter

HeadDiameter

HeadThickness

Diameter ofHole Depth of Hole

FilletRadius

Up toand


dia.


and including8 times

shank dia.

Over 8timesshankdia.Max Min Max Min Max Min Max Min Max Min Max

Oval 0.146 0.146 0.141 0.239 0.229 0.045 0.035 0.107 0.100 To Head 0.375 0.020 ±0.010 ±0.012 ±0.015

Truss0.1460.188

0.1460.188

0.1410.182

0.3180.381

0.3060.369

0.0450.065

0.0350.055

0.1070.141

0.1000.134

To HeadTo Head

0.3750.375

0.0200.025

±0.010±0.010

±0.012±0.012

±0.015±0.015

FlatCounter-

sunk

0.1460.188

0.1460.188

0.1410.182

0.3170.364

0.3070.352

0.0500.060

0.0400.048

0.1070.141

0.1000.134

To HeadTo Head

0.3750.375

....

....±0.010±0.010

±0.012±0.012

±0.015±0.015

Description A small, headed metal fastener having a coaxial cylindrical hole in the end opposite the head which exceeds 112% of the mean shankdiameter.


Can punch its own hole in some plastics, leather and fabrics and be clinched all in one step. The fastener is installed with a rivetinghammer.

Material Steel: Low carbon steel (containing 0.1% carbon or less)Aluminum: Grades 5056, 1100, 2017, 2117 or 6053

Rivets

213

High Strength, DoubleLocking

Orlock® brand,Dome head

L

HD

M B

DOME HEAD

T

DOME ORLOCK® HIGH STRENGTH BLIND RIVETS Ornit

Nominal RivetDiameter &

MaterialPart Number

L

Grip Range

M BRecommended

Hole Size

H D T TypicalShear

Strength(lbs.)

RivetLength(±.012)

Mandrel NailDiameter

(+.003, -.002)

BodyDiameter

(±.002)

HeadHeight(±.008)

HeadDiameter(±.012)

TotalLength(±.079)

3/16Steel/Steel

L48090P 0.354 .059 - .138

0.119 0.189 0.193 - 0.201 0.087 0.386

1.811 882

L48115P 0.453 .138 - .236 1.929 1191

L48140P 0.551 .236 - .335 2.008 1279

1/4Alum/Alum

LH64105P 0.413 .110 - .189

0.164 0.250 0.260 - 0.268 0.118 0.512

1.969

992LH64125P 0.492 .189 - .268 2.047

LH64145P 0.571 .268 - .346 2.126

1/4Steel/Steel

LS65105P 0.413 .079 - .177

0.164 0.256 0.260 - 0.268 0.118 0.512

1.969 2315

LS65125P 0.492 .118 - .256 2.047 2426

LS65145P 0.571 .197 - .335 2.126 2867

LS65165P 0.650 .276 - .413 2.205 3043LS65185P 0.728 .354 - .492 2.284 3263

DescriptionA blind fastener with a self-contained mandrel. The body of the rivet has a dome-shaped head and a shank which tapers slightly where itmeets the mandrel head. The mandrel is designed with two sets of longitudinal grooves that provides internal friction at both ends of thefastening. The section of the mandrel that protrudes above the head of the rivet has circumferential serrations that helps the tool to grip

the mandrel during installation. This top portion of the mandrel ultimately breaks away once the rivet has been installed.


The double-locking system ensures that the mandrel remains tightly fitted within the rivet body, rendering it highly resistant to vibrationand water. The internal friction system with differential force load provides maximum clamp-up without deforming the materials being

gripped. This rivet is designed for heavy industrial use, including automotive, commercial vehicles, buses, railway cars, farm equipmentand electrical engineering.

MaterialAll Aluminum variety: All Steel variety:

Rivet Body- Aluminum 5052Mandrel- Aluminum Almg 6.0 or equivalent

Rivet body- Low carbon steel with zinc yellow chromate;Mandrel- Carbon steel with zinc yellow chromate

Shear Strength Typical shear strengths are listed in the above table. Typical shear strengths are listed in the above table.

Tensile Strength 1/4" nominal rivet diameter: 772 lbs. 3/16" nominal rivet diameter: 661 lbs.1/4" nominal rivet diameter: 1654 lbs.

®Orlock is a registered trademark owned by Ornit.

Rivets

214

High Strength, DoubleLocking

Orlock® brand,Countersunk head

LHD

M

B100o

COUNTERSUNK HEAD

L1

M1

T

COUNTERSUNK ORLOCK® HIGH STRENGTH BLIND RIVETS Ornit

NominalRivet Diam.& Material

PartNumber

L

Grip Range

M M1 BRecom-mended

Hole Size

H D T L1 TypicalShear

Strength(lbs.)

RivetLength(±.012)

Mandrel NailDiameter

(+.003, -.002)

MandrelHead Diam.

(±.002)

BodyDiam.(±.002)

HeadHeight(±.008)

HeadDiam.(±.012)

TotalLength(±.079)

L + MandrelHead

(±.032)

1/4Alum/Alum

LH64115K 0.453 .150 - .228

.164 .253 0.2500.260 -0.268

0.079 0.394

1.886 .609 617

LH64125K 0.491 .189 - .268 1.926 .648 -

LH64175K 0.689 .368 - .464 2.122 .845 1102

1/4Steel/Steel

L64175K 0.689 .368 - .464.164 .253 0.250

0.260 -0.268

0.079 0.3942.122 .845

2095L64195K 0.768 .464 - .543 2.201 .924

DescriptionA blind fastener with a self-contained mandrel. The body of the rivet has a countersunk flat head and a shank which tapers slightly where

it meets the mandrel head. The mandrel is designed with two sets of longitudinal grooves that provides internal friction at both ends ofthe fastening. The section of the mandrel that protrudes above the head of the rivet has circumferential serrations that helps the tool to

grip the mandrel during installation. This top portion of the mandrel ultimately breaks away once the rivet has been installed.


The double-locking system ensures that the mandrel remains tightly fitted within the rivet body, rendering it highly resistant to vibrationand water. The internal friction system with differential force load provides maximum clamp-up without deforming the materials being

gripped. This rivet is designed for heavy industrial use, including automotive, commercial vehicles, buses, railway cars, farm equipmentand electrical engineering.

MaterialAll Aluminum variety: All Steel variety:

Rivet body: 5052 aluminum;Mandrel- Aluminum Almg 6.0 or equivalent

Rivet body- Low carbon steel with zinc yellow chromate;Mandrel- Carbon steel with zinc yellow chromate

Shear Strength Typical shear strengths are listed in the above table. Typical shear strengths are listed in the above table.

Tensile Strength 772 lbs. 1213 lbs.

®Orlock is a registered trademark owned by Ornit.

Rivets

215

Monobolt®/ StructuralProtruding, Large Flange& Countersunk Heads

LHD

M B

L1

LHD

M B

L1

L

HD

M B

L1

100o

G

PROTRUDING HEAD

LARGE FLANGE HEAD

COUNTERSUNK HEAD

DescriptionA two-piece blind fastener consisting of (1) a mandrel with a flared, hollowed-out head and a serrated stem; and (2) a self contained

tubular body with a head which has one of several shapes. The protruding head has a dome shape; the large-flange has a similarshape and is 30-40% wider than the protruding head; the countersunk head has a cone shaped bearing surface with a head angle of

approximately 100°.


This structural rivet has greater tensile strength, greater shear strength and is more resistant to vibration than a standard break-stemblind rivet. The way the mandrel expands radially when pulling through the rivet body enables it to completely fill holes that are out-

of-round, and when the mandrel breaks it leaves a flush finish with the top of the rivet giving it greater weather-resistance than astandard blind rivet.

MaterialAluminum Rivet: 5056 Aluminum; Aluminum Mandrel: 7178 Aluminum

Steel Rivet: Low carbon steel; Steel Mandrel: Carbon steelStainless Steel Rivet: 300 series stainless; Stainless Steel Mandrel: 300 series stainless

Shear StrengthAluminum Rivet/Aluminum Mandrel: 3/16" Diam- 675 lbs., minimum; 1/4" Diam- 1350 lbs., minimum

Steel Rivet/Steel Mandrel: 3/16" Diam- 1500 lbs., minimum; 1/4" Diam- 2750 lbs., minimumStainless Steel Rivet/Stainless Steel Mandrel: 3/16" Diam- 1450 lbs., minimum; 1/4" Diam- 2650 lbs., minimum

Tensile StrengthAluminum Rivet/Aluminum Mandrel: 3/16" Diam- 600 lbs., minimum; 1/4" Diam- 1000 lbs., minimum

Steel Rivet/Steel Mandrel: 3/16" Diam- 1350 lbs., minimum; 1/4" Diam- 2400 lbs., minimumStainless Steel Rivet/Stainless Steel Mandrel: 3/16" Diam- 1150 lbs., minimum; 1/4" Diam- 2350 lbs., minimum

Mandrel Push OutAluminum Rivet/Aluminum Mandrel: 3/16" Diam- 50 lbs.; 1/4" Diam- 100 lbs.

Steel Rivet/Steel Mandrel: 3/16" Diam- 300 lbs.; 1/4" Diam- 500 lbs.Stainless Steel Rivet/Stainless Steel Mandrel: 3/16" Diam- 100 lbs.; 1/4" Diam- 250 lbs.

*Avdel Cherry Textron is the original writer of Monobolt® specifications.

MONOBOLT® STRUCTURAL RIVETS Avdel*

NominalRivet

Diameter

Hole SizeDrill

Number

M B D H D H D H G L L1

MandrelDiameter

RivetDiameter

Protruding HeadLarge Flange

HeadCountersunk

Head

GripRange

RivetLength

RivetLength(Incl.

MandrelHead)

HeadDiameter

HeadThick-ness

HeadDiameter

HeadThick-ness

HeadDiameter

HeadThick-ness

Max Min Nom Nom Nom Nom Nom Nom Nom Nom Max Max

3/16 .201 .191 #11 .118 .187 .375 .085 .515 .100 .335 .070

.062-.270 .416 .727

.125-.331 .486 .800

.214-.420 .537 .855

1/4 .276 .261 17/64 .157 .257 .500 .112 - - .405 .079

.080-.375 .556 .924

.125-.475 .660 1.028

.350-.625 .810 1.174

®Monobolt is a registered trademark of the Avdel Cherry Textron Corporation. Kanebridge’s rivets are not manufactured by or connected with the producers of Monobolt® rivets.

Documents

Rivets New Pgs-03 · Mandrel: Aluminum Alloy 7178, 7075, 5056 or 2024 or equivalent alloy. Shear Strength Rivets shall have ultimate shear loads not less than the minimum ultimate