Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
4 RIGGING HARDWARE
GRADE “S” BOW & DEE SHACKLES ........................................ 100-102COMMERCIAL GALVANIZED DEE SHACKLE ....................................102EYEBOLTS & EYENUTS ....................................................................104TURNBUCKLES & RIGGING SCREWS...................................... 105-107COMMERCIAL CHAIN .......................................................................108GRADE L ANCHOR CHAIN ...............................................................108WIRE ROPE GRIPS ...........................................................................109LOCKABLE GRIPPLES ......................................................................110
RIGGINGHARDWARE
RIGGING HARDWARE
100 Call toll-free 1300 792 464 or visit www.hesnsw.com.au
VAN BEEST GREEN PIN® BOW SHACKLES
VAN BEEST GREEN PIN® BOW SHACKLES
Bow shackles with safety bolt• Material: bow and pin high tensile steel, Grade 6, quenched and tempered
• Safety Factor: MBL equals 6 x WLL
• Standard: EN 13889 and meets performance requirements of US Fed. Spec. RR-C-271 Type IVA Class 3, Grade A
• Finish: hot dipped galvanized
• Temperature Range: -20°C up to +200°C
Bow shackles with screw collar pin• Material: bow and pin high tensile steel, Grade 6, quenched and tempered
• Safety Factor: MBL equals 6 x WLL
• Standard: EN 13889 and meets performance requirements of US Fed. Spec. RR-C-271 Type IVA Class 3, Grade A
• Finish: hot dipped galvanized
• Temperature Range: -20°C up to +200°C
working diameter diameter diameter width width length width length length width thickness weightload bow pin boss boss inside inside bow overall bolt overall nutlimit
a b c d e f g h i j kt mm mm mm mm mm mm mm mm mm mm mm kg
0.5 7 8 16.5 7 12 29 20 48.5 42 34 4 0.060.75 9 10 20 9 13.5 32 22 56 50 40 5 0.111 10 11 22.5 10 17 36.5 26 63.5 60 46 8 0.16
1.5 11 13 26.5 11 19 43 29 74 67 51 11 0.222 13.5 16 34 13 22 51 32 89 82 58 13 0.423.25 16 19 40 16 27 64 43 110 98 75 17 0.74
4.75 19 22 46 19 31 76 51 129 114 89 19 1.186.5 22 25 52 22 36 83 58 144 130 102 22 1.778.5 25 28 59 25 43 95 68 164 150 118 25 2.58
9.5 28 32 66 28 47 108 75 185 166 131 27 3.6612 32 35 72 32 51 115 83 201 178 147 30 4.9113.5 35 38 80 35 57 133 92 227 197 162 33 6.54
17 38 42 88 38 60 146 99 249 202 175 19 8.1925 45 50 103 45 74 178 126 300 249 216 23 14.2235 50 57 111 50 83 197 138 331 269 238 26 19.85
42.5 57 65 130 57 95 222 160 377 301 274 29 28.3355 65 70 145 65 105 260 180 433 330 310 32 39.5985 75 83 162 73 127 329 190 527 380 340 39 62
working diameter diameter diameter width width length width length length width weightload bow pin boss boss inside inside bow overall bolt overalllimit
a b c d e f g h i jt mm mm mm mm mm mm mm mm mm mm kg
0.33 5 6 12 5 9.5 22 16 36 29.5 26 0.020.5 7 8 16.5 7 12 29 20 48.5 38 34 0.050.75 9 10 20 9 13.5 32 22 56 46.5 40 0.1
1 10 11 22.5 10 17 36.5 26 63.5 54 46 0.141.5 11 13 26.5 11 19 43 29 74 59.5 51 0.192 13.5 16 34 13 22 51 32 89 73 58 0.36
3.25 16 19 40 16 27 64 43 110 89 75 0.634.75 19 22 46 19 31 76 51 129 103 89 1.016.5 22 25 52 22 36 83 58 144 119 102 1.5
8.5 25 28 59 25 43 95 68 164 137 118 2.219.5 28 32 66 28 47 108 75 185 153 131 3.1612 32 35 72 32 51 115 83 201 170 147 4.31
13.5 35 38 80 35 57 133 92 227 186 162 5.5517 38 42 88 38 60 146 99 249 203 175 7.4325 45 50 103 45 74 178 126 300 243 216 12.84
35 50 57 111 50 83 197 138 331 272 238 18.1542.5 57 65 130 57 95 222 160 377 310 274 26.2955 65 70 145 65 105 260 180 433 344 310 37.6
a g
f h
b
de
i
c
j
a g
f h
b
d ke
i
c
j
RIGGING HARDWARE
101Call toll-free 1300 792 464 or visit www.hesnsw.com.au
Please refer the complete catalogue for this brand for full product range and specifi cations.
VAN BEEST GREEN PIN® DEE SHACKLES
VAN BEEST GREEN PIN® DEE SHACKLES
Dee shackles with screw collar pin• Material: bow and pin high tensile steel, Grade 6, quenched and tempered
• Safety Factor: MBL equals 6 x WLL
• Standard: EN 13889 and meets performance requirements of US Fed. Spec. RR-C-271 Type IVA Class 3, Grade A
• Finish: hot dipped galvanized
• Temperature Range: -20°C up to +200°C
Dee shackles with safety bolt• Material: bow and pin high tensile steel, Grade 6, quenched and tempered
• Safety Factor: MBL equals 6 x WLL
• Standard: EN 13889 and meets performance requirements of US Fed. Spec. RR-C-271 Type IVA Class 3, Grade A
• Finish: hot dipped galvanized
• Temperature Range: -20°C up to +200°C
working diameter diameter diameter width width length length length weightload bow pin boss boss inside inside overall bolt limit
a b c d e f g ht mm mm mm mm mm mm mm mm kg
0.33 5 6 12 5 9.5 19 33 29.5 0.020.5 7 8 16.5 7 12 22 41.5 38 0.050.75 9 10 20 9 13.5 26 50 46.5 0.09
1 10 11 22.5 10 17 32 59 54 0.141.5 11 13 26.5 11 19 37 68 59.5 0.192 13.5 16 34 13 22 43 81 73 0.32
3.25 16 19 40 16 27 51 97 89 0.544.75 19 22 46 19 31 59 112 103 0.876.5 22 25 52 22 36 73 134 119 1.34
8.5 25 28 59 25 43 85 154 137 2.089.5 28 32 66 28 47 90 167 153 2.7712 32 35 72 32 51 94 180 170 3.72
13.5 35 38 80 35 57 115 209 186 5.1417 38 42 88 38 60 127 230 203 6.8525 45 50 103 45 74 149 271 243 11.45
35 50 57 111 50 83 171 305 272 16.8642.5 57 65 130 57 95 190 345 310 24.6155 65 70 145 65 105 203 376 344 32.65
working diameter diameter diameter width width length length length thickness weightload bow pin boss boss inside inside overall bolt nutlimit
a b c d e f g h it mm mm mm mm mm mm mm mm mm kg
2 13.5 16 34 13 22 43 81 82 13 0.393.25 16 19 40 16 27 51 97 98 17 0.674.75 19 22 46 19 31 59 112 114 19 1.08
6.5 22 25 52 22 36 73 134 130 22 1.668.5 25 28 59 25 43 85 154 150 25 2.469.5 28 32 66 28 47 90 167 166 27 3.4
12 32 35 72 32 51 94 180 178 30 4.5113.5 35 38 80 35 57 115 209 197 33 6.117 38 42 88 38 60 127 230 202 19 7.63
25 45 50 103 45 74 149 271 249 23 13.2535 50 57 111 50 83 171 305 269 26 18.5342.5 57 65 130 57 95 190 345 301 29 25.94
55 65 70 145 65 105 203 376 330 32 35.3385 75 83 162 73 127 229 427 380 39 52.97
g
a
f
b
de
c
h
g
a
f
b
d ie
c
h
COMMERCIAL GALVANIZED DEE SHACKLE
NOT SUITABLE FOR LIFTING APPLICATIONS
• Commercial Grade Dee Shackles are suitable for mining, industrial and domestic applications.
• Manufactured from mild steel with a galvanized fi nish
RIGGING HARDWARE
102 Call toll-free 1300 792 464 or visit www.hesnsw.com.au
SIZE WEIGHT/unit DIMENSIONS mm mm KG B D D1 C
5 0.015 10 5 5 19
6 0.025 12 6 6 24
8 0.054 16 8 8 32
10 0.109 20 10 10 40
12 0.205 25 12 12 48
16 0.480 32 16 16 64
20 0.815 38 20 20 76
22 1.285 44 22 22 85
25 1.866 53 25 24 95
Inside Inside Length Width Approx. Weight Each Dia. Bow Dia. Pin Width Chain Type Anchor of Bow Screw SafetyWLL d D W L Type L B Pin PinTonnes m mm mm mm mm mm kg kg
0.33 5 6 10 - 22 15 0.02 -
0.50 6 8 12 22 29 20 0.06 0.07
0.75 8 10 13 26 31 21 0.11 0.13
1.00 10 11 17 32 37 26 0.15 0.17
1.50 11 13 18 37 43 29 0.21 0.25
2.00 13 16 21 41 48 33 0.37 0.44
3.25 16 19 27 51 61 43 0.65 0.79
4.75 19 22 32 60 72 51 1.06 1.26
6.50 22 25 37 71 84 58 1.56 1.88
8.50 25 29 43 81 95 68 2.32 2.78
9.50 29 32 46 90 108 74 3.28 3.87
12.00 32 35 52 100 119 83 4.51 5.26
13.00 35 38 57 113 133 92 5.43 6.94
17.00 38 41 60 124 146 98 7.89 8.79
25.00 44 51 73 146 178 127 13.40 14.99
35.00 51 57 83 171 197 146 18.85 20.65
45.00 57 63 95 181 222 160 26.06 29.01
55.00 63 70 105 203 267 184 37.86 41.05
85.00 76 83 127 229 330 200 58.68 62.24
120.00 89 95 146 267 381 241 - 110.0
150.00 102 108 165 318 432 279 - 160.0
• Manufactured and tested to the requirements of AS 2741-2002
• Galvanised fi nish
• Larger sizes avaiable
GRADE “S” BOW AND DEE SHAKLES
Dee Shackle With Screw Pin
Bow Shackle With Screw Pin
Dee Shackle With Safety Pin
Bow Shackle With Safety Pin
I.S. Range Collared Eyebolts: DIN 580 specifi cation. Surface fi nish is silver zinc plating.
M8 M10 M12 M16 M20 M22 M24
20 25 30 35 40 50 50
Metric threads
Eye diameter (mm)
I.S. Range Collared Eyenuts: DIN 580 specifi cation. Surface fi nish is silver zinc plating.
M8 M10 M12 M16 M20 M22 M24
20 25 30 35 40 50 50
Metric threads
Eye diameter (mm)
EYEBOLTS AND EYENUTS
Collared Lifting Eyebolts: Standard shot blasted fi nish. Optional fi nishes available on request.
Metric, BSW and UNC thread forms. Special thread forms available on request. AS2317.
Weld on Load Rings: Multi-directional loading. Made in Australia.
Forged Eyenuts: Standard shot blasted fi nish. Optional fi nishes available on request.
Metric and BSW thread forms.
M10 M12 M16 M20 M22 M24 M30 M33 M36 M42 M48 M56 M64 M76
3/8” 1/2” 5/8” 3/4” 7/8” 1” 1.1/8” 1.1/4” 1.1/2” 1.3/4” 2” 2.1/4” 2.1/2” 3”
14 19 24 29 33 38 48 48 55 66 72 95 95 106
Metric threads
BSW & UNC
Eye diameter (mm)
WLL (t) A mm B mm C mm D mm E mm F mm G mm H mm Part Number
2.0 40 82 34 68 28 14 14 92 TWLP200
4.0 53 104 46 90 33 18 18 116 TWLP400
6.7 68 138 60 116 45 23 23 155 TWLP670
10.0 68 141 60 132 56 27 27 175 TWLP1000
16.0 102 210 92 192 70 38 30 240 TWLP1600
M10 M12 M16 M20 M22 M24 M30 M33 M36 M42 M48 M56 M64 M76
3/8” 1/2” 5/8” 3/4” 7/8” 1” 1.1/8” 1.1/4” 1.1/2” 1.3/4” 2” 2.1/4” 2.1/2” 3”
24 24 28 32 33 38 48 48 55 66 72 95 95 106
Metric threads
BSW & UNC
Eye diameter (mm)
Longshank Eyebolts: Standard shot blasted fi nish. Optional fi nishes available on request.
Metric and BSW thread forms.
M10 M12 M16 M20 M22 M24 M30 M33 M36 M42 M48 M56 M64 M76
3/8” 1/2” 5/8” 3/4” 7/8” 1” 1.1/8” 1.1/4” 1.1/2” 1.3/4” 2” 2.1/4” 2.1/2” 3”
24 24 28 32 33 38 48 48 55 66 72 95 95 106
Metric threads
BSW & UNC
Eye diameter (mm)
RIGGING HARDWARE
104 Call toll-free 1300 792 464 or visit www.hesnsw.com.au
TURNBUCKLES AND RIGGING SCREWS
Clevis and Clevis
Turnbuckles, Grades
L, P and S: Certifi ed to
AS2319:2001. Made in
Australia. Supplied tested
and with full certifi cation.
Eye and Eye Turnbuckles,
Grades L, P and S: Certifi ed
to AS2319:2001. Made in
Australia. Supplied tested
and with full certifi cation.
Clevis and Eye
Turnbuckles, Grades
L, P and S: Certifi ed to
AS2319:2001. Made in
Australia. Supplied tested
and with full certifi cation.
Clevis & Clevis Rigging
Screws - Grades L, P & S.
Certifi ed to AS2319:2001.
Made in Australia. Supplied
tested and with full
certifi cation.
Eye & Eye Rigging Screws
- Grades L, P & S. Certifi ed
to AS2319:2001. Made in
Australia. Supplied tested
and with full certifi cation.
Clevis & Eye Rigging
Screws - Grades L, P & S.
Certifi ed to AS2319:2001.
Made in Australia. Supplied
tested and with full
certifi cation.
Dimensions Working Load Limits (WLL) tNominal Size Open (mm) Closed (mm) L P SM10 350 240 0.30 0.60 0.80M12 470 335 0.50 1.00 1.20M16 490 355 0.75 1.60 2.00M20 520 440 1.25 2.50 3.20M24 585 450 2.50 4.00 5.00M33 780 630 n/a 8.00 10.001 1/4” 670 520 5.00 n/a n/a1 1/2” 740 550 6.00 n/a n/a
Dimensions Working Load Limits (WLL) tNominal Size Open (mm) Closed (mm) L P SM10 335 230 0.30 0.60 0.80M12 470 330 0.50 1.00 1.20M16 485 350 0.75 1.60 2.00M20 515 385 1.25 2.50 3.20M24 570 440 2.50 4.00 5.00M33 806 656 n/a 8.00 10.001 1/4” 720 570 5.00 n/a n/a1 1/2” 740 600 6.00 n/a n/a
Dimensions Working Load Limits (WLL) tNominal Size Open (mm) Closed (mm) L P SM10 340 235 0.30 0.60 0.80M12 470 330 0.50 1.00 1.20M16 490 355 0.75 1.60 2.00M20 520 390 1.25 2.50 3.20M24 580 445 2.50 4.00 5.00M33 793 643 n/a 8.00 10.001 1/4” 690 525 5.00 n/a n/a1 1/2” 740 570 6.00 n/a n/a
Dimensions Working Load Limits (WLL) tNominal Size Open (mm) Closed (mm) L P SM10 395 265 0.30 0.60 0.80M12 525 340 0.50 1.00 1.20M16 535 360 0.75 1.60 2.00M20 555 390 1.25 2.50 3.20M24 740 555 2.50 4.00 5.00M33 904 628 5.00 8.00 10.001 1/4” 830 610 5.00 8.00 10.001 1/2” 890 660 6.00 10.00 12.001 3/4” 920 690 7.50 12.00 16.002” 997 762 10.00 16.00 20.002 1/4” 1029 819 15.00 20.00 28.002 1/2” 1035 838 20.00 28.00 36.00
Dimensions Working Load Limits (WLL) tNominal Size Open (mm) Closed (mm) L P SM10 380 260 0.30 0.60 0.80M12 520 340 0.50 1.00 1.20M16 525 350 0.75 1.60 2.00M20 545 380 1.25 2.50 3.20M24 725 540 2.50 4.00 5.00M33 936 660 5.00 8.00 10.001 1/4” 837 590 5.00 8.00 10.001 1/2” 927 648 6.00 10.00 12.001 3/4” 946 686 7.50 12.00 16.002” 965 717 10.00 16.00 20.002 1/4” 1016 813 15.00 20.00 28.002 1/2” 1016 813 20.00 28.00 36.00
Dimensions Working Load Limits (WLL) tNominal Size Open (mm) Closed (mm) L P SM10 385 260 0.30 0.60 0.80M12 525 335 0.50 1.00 1.20M16 535 355 0.75 1.60 2.00M20 550 385 1.25 2.50 3.20M24 735 555 2.50 4.00 5.00M33 920 644 5.00 8.00 10.001 1/4” 876 603 5.00 8.00 10.001 1/2” 952 673 6.00 10.00 12.001 3/4” 959 705 7.50 12.00 16.002” 978 743 10.00 16.00 20.002 1/4” 1029 813 15.00 20.00 28.002 1/2” 1029 826 20.00 28.00 36.00
RIGGING HARDWARE
105Call toll-free 1300 792 464 or visit www.hesnsw.com.au
COMMERCIAL TURNBUCKLES
RATED TURNBUCKLE
Eye-Eye Turnbuckle - NOT SUITABLE FOR LIFTING APPLICATIONS
• Hook or eye end fi ttings for light duty tensioning of wire rope assemblies
• Sizes available are from 6mm - 25mm
• Zinc plated fi nish
Jaw-Jaw Turnbuckle - SUITABLE FOR LIFTING APPLICATIONS
Generally used for straight or in line tensioning in conjunction with wire rope
and chain assemblies when heavy duty straining and lifting applications are
required.
• Manufactured from high tensile material quenched and tempered hot dipped galvanized fi nish suitable for outdoors.
• Available in imperial sizing and jaw end fi ttings.
• Meets the design requirements of US Federal Specifi cations.
• Proof tested to 2 x WLL and Minimum Break Force is 5 x WLL.
• Test certifi cates available upon request.
Hook-Eye Turnbuckle - NOT SUITABLE FOR LIFTING APPLICATIONS
SIZE WEIGHT/unit DIMENSIONS mmmm KG L L1 D D2
6 0.067 80 35 6 9
8 0.13 105 50 8 11
10 0.23 130 62 10 16
12 0.35 140 65 12 18
16 0.90 178 88 16 24
20 1.43 215 110 20 28
22 2.10 240 120 22 32
25 2.62 255 135 25 36
SIZE WLL WEIGHT/unit DIMENSIONS mmin. T KG A B C E F G M N
3/8 0.54 0.37 9.65 12.7 152 410 258 22.1 441 289
1/2 1 0.71 12.7 16 152 470 292 26.9 508 330
5/8 1.59 1.56 16 19 229 662 401 33.3 715 454
3/4 2.36 2.98 19.1 23.4 305 851 508 38.1 917 574
7/8 3.27 3.71 22.4 28.7 305 892 543 44.5 967 618
1 4.54 5.53 25.4 30 305 933 577 52.5 1018 662
1 1/4 6.89 9.36 31.8 44.5 305 1012 644 71.5 1119 750
1 1/2 9.71 13.9 38.1 52 305 1054 673 71.5 1181 800
1 3/4 12.7 24.5 44.5 60 457 1356 899 86 1503 1046
2 16.8 42.8 51 63.5 610 1766 1157 93.5 1949 1339
2 1/2 27.2 75 63.5 73 610 1854 1244 113 2087 1478
SIZE WEIGHT/unit DIMENSIONS mmmm KG D D1 D2 L L1
6 0.052 6 8 9 80 35
8 0.098 8 10 11 105 50
10 0.226 10 16 16 130 62
12 0.338 12 18 18 140 65
16 0.898 16 24 24 178 88
20 1.595 20 28 28 215 110
22 2.18 22 32 32 240 120
25 2.8 25 36 36 255 135
RIGGING HARDWARE
106 Call toll-free 1300 792 464 or visit www.hesnsw.com.au
RIGGING SCREWS
Rigging Screws are used to provide a means for length adjustment and tensioning. They are used
with guys for masts, towers, tall structures and engineering applications. Their elongated eye or
clevis end fi ttings allow easy connection to shackles and wire rope assemblies. The enclosed
section of the body provides a reservoir for lubricant to protect the threads from corrosion, making
them ideal for permanent outdoor use or in a marine environment.
Rigging Screw Clevis & Clevis
Metric - Grades L, P & S
(Units shown in mm)
Rigging Screw Clevis & Eye
Metric - Grades L, P & S
(Units shown in mm)
Rigging Screw Eye & Eye
Metric - Grades L, P & S
(Units shown in mm)
NOMINAL A A B C D E F K Grade L Grade P Grade S SIZE CLOSED OPEN WLL (t) WLL (t) WLL (t)
M10 265 395 30 14 30 8.5 180 10 0.30 0.60 0.80
M12 340 525 36 15 35 8.5 230 10 0.50 1.0 1.2
M16 360 535 45 20 40 9.0 230 12 0.75 1.6 2.0
M20 390 555 55 22 46 10.5 230 16 1.25 2.5 3.2
M24 555 740 59 30 58 13.0 360 20 2.50 4.0 5.0
M33 628 904 80 38 75 14.0 380 24 5.0 8.0 10.0
NOMINAL A A B C D E F G H J K Grade L Grade P Grade S SIZE CLOSED OPEN WLL (t) WLL (t) WLL (t)
M10 260 385 30 14 30 8.5 180 11 21 7 10 0.30 0.60 0.80
M12 335 525 36 15 35 8.5 230 14 30 9 10 0.50 1.0 1.2
M16 355 535 45 20 40 9.0 230 17 36 12 12 0.75 1.6 2.0
M20 385 550 55 22 46 10.5 230 21 42 14 16 1.25 2.5 3.2
M24 555 735 59 30 58 13.0 360 25 51 17 20 2.50 4.0 5.0
M33 644 920 80 38 75 14.0 380 33 70 24 24 5.0 8.0 10.0
NOMINAL A A E F G H J Grade L Grade P Grade S SIZE CLOSED OPEN WLL (t) WLL (t) WLL (t)
M10 265 395 8.5 180 12 10 7 0.30 0.60 0.80
M12 340 525 8.5 230 15 10 9 0.50 1.0 1.2
M16 360 535 9.0 230 17 12 12 0.75 1.6 2.0
M20 390 555 10.5 230 21 16 12 1.25 2.5 3.2
M24 555 740 13.0 360 25 20 17 2.50 4.0 5.0
M33 628 904 14.0 380 33 24 24 5.0 8.0 10.0
RIGGING HARDWARE
107Call toll-free 1300 792 464 or visit www.hesnsw.com.au
COMMERCIAL CHAIN
GRADE L ANCHOR CHAIN
Regular proof coil galvanised chain
Proof Coil Chain is manufactured from low carbon steel and is commonly used for
agricultural, industrial, manufacturing, marine and general engineering applications
• Available packed in 50kg pails, 500kg drums or cut lengths.
• Chain is available in self colour, hot dip galvanised and zinc fi nish.
NOT SUITABLE FOR LIFTING APPLICATIONS.
Manufactured in a short link confi guration meeting the requirements of Australian
Standard AS2321, Grade L Chain is the highest quality lower tensile steel available for
lifting purposes and recommended for most marine and mooring applications.
RIGGING HARDWARE
108 Call toll-free 1300 792 464 or visit www.hesnsw.com.au
50KG PAIL PACK 500KG DRUM DIMENSIONS
SIZE LENGTH LENGTH B C D mm mtr mtr mm mm mm
3 249 2490 13.1 15.7 3
4 153 1525 16 18.6 3.8
5 96.5 965 19.4 22 4.75
6 60 600 23.5 26 6
8 37 370 29.5 32 7.6
10 23.5 235 36 39 9.5
13 13.8 138 46 49 12
16 9 91 56 60 16
20 - - 60 71 73.3 20
24 - - 42 84.8 87 24
Chain Size WLL S R F Self-colour Galvanised mm tonnes mm mm mm metres/100kg metres/100kg
6 0.40 6.3 18.8 21.6 116.0 110.0
8 0.64 8.0 23.8 27.0 71.4 67.8
10 1.00 10.0 29.8 34.3 45.5 43.2
13 1.70 12.7 38.0 43.0 29.6 27.8
16 2.58 16.0 47.8 54.9 17.8 17.5
20 4.03 20.0 59.2 68.5 11.3 11.1
22 5.06 22.0 64.9 77.0 9.5 9.2
• Sizes available are from 3mm - 25mm
• Zinc plated fi nish on both U-bolt and saddle
• Tolerances may vary for commercial products
NOT SUITABLE FOR LIFTING PURPOSES
• Sizes available are from 6mm - 52mm
• Hot dipped galvanized fi nish on both U-bolt and saddle
• Tolerances may vary for commercial products
• Conforms to AS2076 and are marked with AS and size
NOT SUITABLE FOR LIFTING PURPOSES
HEAVY DUTY COMMERCIAL WIRE ROPE GRIPS
AUSTRALIAN STANDARD WIRE ROPE GRIPS
PRODUCT SIZE WEIGHT/unit DIMENSIONS mm CODE in mm KG A B C D (in.) E F G
WRGC003 1/8 3 0.017 11 14 14 3/16 10.8 22 20
WRGC004 3/16 4-5 0.03 14.5 15 16.5 1/4 13 26 24
WRGC006 1/4 6 0.053 17 18.5 20 5/16 15 32 31.5
WRGC008 5/16 8 0.06 18.3 20 22 5/16 16 35 34
WRGC010 3/8 10 0.103 22.5 22 27 3/8 22 40.5 41.8
WRGC013 1/2 12 0.21 27 26 33 7/16 23.3 49 51
WRGC014 9/16 14 0.23 30 27.5 35 1/2 26 54 54
WRGC016 5/8 16 0.25 32.5 28.5 40 1/2 28 57.5 59
WRGC020 3/4 20 0.37 34.5 30 42 9/16 32 59.5 68.5
WRGC022 7/8 22 0.5 41 35 46 5/8 37 69 78
WRGC025 1 25 0.6 45.5 38 55 5/8 41 75 87.5
PRODUCT SIZE WEIGHT/unit DIMENSIONS mm CODE mm KG A B C D (in) E F G
WRG06AS 6 0.04 14 15 20 M6 12 28 26
WRG08AS 8 0.069 18 19 22 M8 14 34 32
WRG10AS 10 0.12 20 23 27 M10 17 42 40
WRG12AS 12 0.132 22.3 28 32 M10 20 50 48
WRG14AS 14 0.223 27 32 38 M12 22 52 52
WRG16AS 16 0.351 31 32 41 M14 26 66 64
WRG18AS 18 0.488 35 38 47 M16 27 68 68
WRG20AS 20 0.98 43 46 58 M20 36 89 88
WRG22AS 22 1.123 40 46 61 M20 32 72 92
WRG26AS 26 1.425 50 50 66 M22 38 90 96
WRG28AS 28 1.56 52 50 70 M22 39 92 104
WRG32AS 32 1.9 56 55 75 M24 41 112 120
WRG38AS 38 2.1 64 55 78 M24 48 120 122
WRG44AS 44 3.0 73 62 90 M27 52 135 150
WRG52AS 52 4.2 85 69 103 M30 56 154 185
RIGGING HARDWARE
109Call toll-free 1300 792 464 or visit www.hesnsw.com.au
4 simple steps to secure in seconds
LOCKABLE GRIPPLES
New, innovative, lockable system for securing wire ropes - quickly.
The Lockable Gripple now makes catenary and bracing wire rope installation
easier and faster. The Lockable Gripple is designed to secure the ends of wire
ropes by simply pushing them through the Gripple in one continuous loop.
Hands free, the integral locking screws can be tightened to ensure total security
under dynamic load conditions.
Easy to use - faster to fi t!
• Simple push-fi t assembly
• Hands-free adjustment
• Automatic locking wedges
• Easy tensioning
• Secure locking screws
The unique locking screw design combats the
effects of wind-gallop a typical feature of outside
applications.
Once the wire rope length and tension have been
set, tightening the lock screws fi rmly secures the
internal locking wedges immovably in place.
As well as preventing wear this feature allows the
product to be used on both steel and fi bre core
wire rope constructions.
Applications:
• Overhead catenary wires
• Carnival and promenade lighting
• Exhibition hall displays
• Extraction duct bracing
• Aerial bracing
• Marquee bracing
• Shade cloth bracing
• Tree bracing
Self-Locking Working Gripple Working Wire Rope Grip Range and Minimum Range Model Load Limit Breaking Load mm kg kg mm
2.00 10-80 400 1.5-2.5
3.00 80-200 1000 2.5-4.0
5.00 200-400 2000 4.0-5.5
6.00 400-545 2725 5.5-7.0
8.00 545-1280 6400 7.0-8.5
10.00 545-1280 6400 8.5-10.0
11.00 1280-1820 9100 10.0-11.5
13.00 / 1/2in. 1280-1820 9100 11.5-13.0
RIGGING HARDWARE
110 Call toll-free 1300 792 464 or visit www.hesnsw.com.au