Rev.: A Page - Qi-Hardware

C:\Documents and Settings\uesr\\micro usb female.dwg Model (1)Approved/Date Checked/Date Written/Date
4/10/08
1.0 Scope : This specification covers the requirements for product performance and test methods of
Micro USB Series Connectors of the part numbers specified as bellow.
Product shall be of the design, construction and physical dimensions specified in the applicable product
drawing.
2.2 Temperature Range: storage : -20 to +60 ;
operating : -55 to +80 : Nominal : +20
2.3 Current Rating: Signal only : 1.0A/Pin
Power apply: 1.8A/Pin (Pin No.1,5) 0.5A/Pin (Pin No.2~4)
3.0 Test Condition:
All tests shall be performed as bellow conditions unless otherwise specified.
3.1 Temperature range : +15 to +35
3.2 Humidity range: 25% to 85%
3.3 Atmospheric Pressure : 86kPa to 106 kPa (860 to 1060 mber)
4.0 Test Methods and Requirements:
4.1 Examination of product:
4.1.1 Examination of
accordance with each drawing.
measuring instruments.
2).Structure shall be meet the design
and dimensional requirements of
Approved/Date Checked/Date Written/Date
4.2.1 Low Level Contact
30mΩ(Max) when measured at
20mv(max) open circuit at
Ω after 10000 insertion/extraction
per hour
4.2.2 Insulation Resistance EIA 364-21 (or MIL-STD-202F, Method
302, Test Condition B)
mated and unmated connector
detail a standard method to assess
the insulation resistance of MicroUSB
connectors. This test procedure is used
to determine the resistance offered by
insulation connector to a 500V DC
potential current through or on the
surface of the members.
1).Initial: 100 MΩ Minimum
4.2.3 Dielectric
Withstanding Voltage
301, Test Condition B)
mated and unmated connector
MICRO USB connector can operate
safely at its rated voltage and withstand
momentary over potentials due to
switching, surges and/or other similar
phenomena.
1).No flashover or insulation
4.3.1 Durability EIA 364-09 Mate and unmate Connector
assemblies for 10000 cycles at
maximum rated of 500 cycles per hour.
The object of this test procedure is to
detail a uniform test method for
determining the effects caused by
subjecting a connector to the
conditioning action of inserting and
extraction, simulating the expected life
of the connectors. Durability cycling
with a gauge is intended only to
produce mechanical stress. Durability
and wear stress.
1).Shall meet visual requirement,
show no physical damage.
4.3.2 Mechanical Shock EIA-364-27B Subject mated connector to 50G’s half-sine shock pulses of 11msec duration. Three shocks in each direction applied along three mutuall perpendicular planed for a total of 18 shocks
No discontinuities of 1 microsecond or
long duration. See note
4.3.3 Vibration EIA-364-28D Subject mated connectors to 10~55~10Hz traversed in 1 minute at 1.52mm amplitude 2 hours each of 3 mutually perpendicular planes.
No discontinuities of 1 microsecond or
long duration. See note
GAUGE or TENSION TESTER.
The object of this test is to detail a
standard method for determining the
mechanical forces required for inserting
a Mini USB connector.
4.3.5 Connector Unmating
1).Initial : 10 Newtons Minimum
Minimum
GAUGE or TENSION TESTER in same
direction.
4.4.1 Thermal Shock
Method 107G Condition A.)
between –55 to +85.
resistance of a USB connector to exposure at
extremes of high and low temperatures and to
the shock of alternate exposures to these
extremes, simulating the wrost case conditions
for storage, transportation and application.
1).Shall meet visual
additional tests as specified in
TEST SEQUENCE in Section 5
4.4.2 Humidity EIA 364-31, Test Condition A Method III, (or MIL-202F, Method 103B Test Condition B.) Temperature -10~65, Humidity 90 to 98%, Under 7 Cycles (168hr) The object of this test procedure is to detail a
standard method for the evaluation of the
properties of materials used in Micro USB
connectors as these influenced by the effects of
high humidity and heat.
4.4.3 Salt Spray
MIL-STD-202F, Method 101D, Test Condition B Subject mated connectors to 48 hours at 35
with 5%-Salt-solution concentration.
additional tests as specified in
TEST SEQUENCE in Section 5
4.4.4 Temperature Life EIA 364-17 Test Condition 3 Method A, Subject mated connectors to temperature life
at 85 for 96hours
DOC. No.:SP-Micro USB Rev.: A Page:6/7
4.4.5 Solderability EIA 364-52 After one hour steam aging.
The object of test procedure is to detail
a unfirm test methods for determining
USB connector solderability. The test
procedure contained here utilizes the
solder dip technique. It is not intended
to test or evaluate solder cup, solder
eyelet, other hand-soldered type or
SMT type terminations.
soldered shall at least 95% covered
with new solder coating,as specified in
Category 2.
2) for MANUAL SOLDERING :
MIL-STD-202F, Method 210A, Test
3) for REFLOW SOLDERING :
1). No mechanical defect on housing
or other parts.
4.4.6 Resistance to
Test Group (a) Sample Groups
Test Item Test Description A B C D E F G H I J K L
4.1.1 Examination of product 1,13 1,5 1,8 1,3 1 3 1,5 1 3 1 6
4.2.1 Low Level Contact Resistance 2,10 2,4 2,4 2 5
4.2.2 Insulation Resistance 3 11 2,6
4.2.3 Dielectric Withstanding Voltage 4 12 3,7
4.3.1 Durability 7
4.3 3 Vibration 4
4.4.1 Thermal Shock 5
4.4.5 Solderability 2
Number of Test Samples (Minimum)
5 5 5 5 5 5 5 5
Q M F Z 2 C o m p o n e n t - P l a s t i c s
F r i d a y , O c t o b e r 2 4 , 2 0 0 3
E1 06
76 4
P O L Y P L A S T I C S C O L T D
V E C T R A D I V , K A S U M I G A S E K I B L D G , 6 T H F L 2 - 5 K A S U M I G A S E K I 3 - C H O M E C H I Y O D A - K U T O K Y O 1 0 0 - 6 0 0 6 J A P A N
M at
er ia
2 ): -
V o l u m e R e s i s t i v i t y ( 10
x o hm -c m) : 1 6
I S O F l e x u r a l S t r e n g t h (M Pa ): -
I S O I z o d I m p a c t ( kJ /m
2 ) : -
D i m e n s i o n a l S t a b i l i t y ( %)
: 0
-
I S O C h a r p y I m p a c t ( kJ
/m 2 ) :
( d )
V i r g i n a n d r e g r i n d u p t o 5 0 % b y w e i g h t i n c l . h a v e t h e s a m e b a s i c m a t e r i a l c h a r a c t e r i s t i c s f o r c o l o r s
N C a n d B K .
( e )
I n a d d i t i o n , r e g r i n d a t 2 6 t o 5 0 % h a v e t h e s a m e b a s i c c h a r a c t e ri s t i c s a t a m i n i m u m o f 1 . 5 m m e x c e p t
R T I ' s f o r t h e M e c h a n i c a l w / I m p a c t p r o p e r t y i s 1 8 0 C .
R ep
®
U L 9 4 s m a l l - s c a l e t e s t d a t a d o e s n o t p e r t a i n t o b u i l d i n g m a t e r i al s , f u r n i s h i n g s a n d r e l a t e d c o n t e n t s . U L 9 4 s m a l l - s c a l e
t e s t d a t a i s i n t e n d e d s o l e l y f o r d e t e r m i n i n g t h e f l a m m a b i l i t y o f p l a s t i c m a t e r i a l s u s e d i n c o m p o n e n t s a n d p a r t s
o f e n d - p r o d u c t d e v i c e s a n d a p p l i a n c e s , w h e r e t h e a c c e p t a b i l i t y o f t h e c o m b i n a t i o n i s d e t e r m i n e d b y U L I .
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This test report cannot be reproduced, except in full, without prior written permission of the Company.
This Test Report is issued by the Company under its General Conditions of Service printed overleaf or available on request and accessible at http://www.sgs.com/terms_and_conditions.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this Test Report is advised that information contained hereon reflects the
Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law.
SGS Taiwan Ltd. No. 208, Chung Hwa 2nd Road San Min District Kaohsiung, Taiwan. / 208
t (886-7) 323-0920 f (886-7) 315-7484 www.tw.sgs.com Member of SGS Group
Sample Description :
Style/Item No. :
Determination of Hexavalent Chromium for non-metallic samples by UV/Vis Spectrometry.
Test Report
POLYPLASTICS TAIWAN CO., LTD. NO.13, JIANYE RD., DALIAO TOWNSHIP, KAOHSIUNG COUNTY 831, TAIWAN (R.O.C.)
VECTRA
NATURE / BLACK
The following sample(s) was/were submitted and identified by/on behalf of the client as :
A130 VF2001/BK010P, E130G VF2201/BK210P, E130i VF2201/ BK205P/BK210P/BK211P,E463i VF2201/BK210P, E471i VF2201/ BK210P/BK211P, E472i BK210P, E473i VF2201/BK210P, E480i VF2201/BK210P,E481i VF2201/BK210P, L130 VF2201, S135 VF2001/BK010P, S476 BK210P
2009/04/20 TO 2009/04/23
In accordance with the RoHS Directive 2002/95/EC, and its amendment directives.
With reference to IEC 62321:2008 Procedures for the Determination of Levels of Regulated Substances in Electrotechnical Products.
Determination of Cadmium by ICP-AES.
Please refer to next page(s).
Determination of PBB and PBDE by GC/MS.
Result
No.1
(1)
NO.1 : MIXED ALL PARTS:VECTRA
Test Report No. : KA/2009/41514 Date : 2009/04/23 Page : 2 of 6
POLYPLASTICS TAIWAN CO., LTD. *KA/2009/41514*
NO.13, JIANYE RD., DALIAO TOWNSHIP, KAOHSIUNG COUNTY 831, TAIWAN (R.O.C.)
Heptabromobiphenyl
Octabromobiphenyl
Nonabromobiphenyl
Sum of PBDEs
16. This is the additional test report of KA/200X/XXXXX which was issued on yyyy/mm/dd.
Please refer to KA/200X/XXXXX for original information.
6. The sample(s) was/were analyzed on behalf of the applicant as mixing sample in one testing. The above result(s) was/were only given as the informality value.
2. n.d. = Not Detected
5. "-" = Not Regulated
4. The exemption of DecaBDE in polymeric application according 2005/717/EC was overruled by the European Court of Justice by its decision of 01.04.2008. Subsequently DecaBDE will be included in the sum of PBDE after 01.07.2008
15. This report supersedes all pervious documents bearing the test report number KA/200X/XXXXX.
Note 1. mg/kg = ppm0.1wt% = 1000ppm
1) These samples were dissolved totally by pre-conditioning method according to below flow chart.Cr6+ test
method excluded
2) Name of the person who made measurement: Hungming Li
3) Name of the person in charge of measurement: Ray Chang
Cr6
Steel, copper, aluminum, solder Aqua regia, HNO3, HCl, HF, H2O2
Glass HNO3/HF
Silver HNO3
Others Any acid to total digestion
PbCd
depended on different sample
material (as below table)
Add appropriate amount
of digestion reagent
Hg
PBB/PBDE analytical FLOW CHART
1) Name of the person who made measurement: Anson Tsao
2) Name of the person in charge of measurement: Ray Chang
First testing process
Optional screen process
Filter
** End of Report **
Test Report No. CANEC0900169802 Date: 17 Jan 2009 Page 1 of 7
SHENZHEN DUOXIN INDUSTRIAL CO.,LTD
CHINA
The following sample(s) was/were submitted and identified on behalf of the clients as :

Date of Sample Received : 13 Jan 2009
Testing Period : 13 Jan 2009 - 16 Jan 2009
Test Requested : Selected test(s) as requested by client.
: Please refer to next page(s).Test Method
Test Results : Please refer to next page(s).
Signed for and on behalf of
SGS-CSTC Ltd.
Sr. Engineer Huang Fang, Sunny
Test Results:
Yellow transparent liquid :Description for specimen 1
Heavy metal(s)
Cadmium (Cd) N.D.mg/kg 2IEC 62321/2nd CDV (111/95/CDV), ICP-OES
Lead (Pb) N.D.mg/kg 2IEC 62321/2nd CDV (111/95/CDV), ICP-OES
Mercury (Hg) N.D.mg/kg 2IEC 62321/2nd CDV (111/95/CDV), ICP-OES
Hexavalent Chromium (CrVI) by
Note:
Flame Retardants
Monobromobiphenyl mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Dibromobiphenyl mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Tribromobiphenyl mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Tetrabromobiphenyl mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Pentabromobiphenyl mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Hexabromobiphenyl mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Heptabromobiphenyl mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Octabromobiphenyl mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Nonabromobiphenyl mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Decabromobiphenyl mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Sum of PBDEs mg/kg - N.D. -
Monobromodiphenyl ether mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Dibromodiphenyl ether mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Tribromodiphenyl ether mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Tetrabromodiphenyl ether mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Pentabromodiphenyl ether mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Hexabromodiphenyl ether mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Heptabromodiphenyl ether mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Octabromodiphenyl ether mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Nonabromodiphenyl ether mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Decabromodiphenyl ether ## mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Note:
4. "-" = Not regulated
5. ## = The exemption of DecaBDE in polymeric application according 2005/717/EC was overruled by the
European Court of Justice by its decision of 01.04.2008. Subsequently DecaBDE will be included in the sum of
PBDE after 01.07.2008
PFOS Perfluorooctane sulfonates
Note:
Reference Information: Directive 2006/122/EC
(1) May not be placed on the market or used as a substance or constituent of preparations in a concentration
equal to or higher than 0.005 % by mass.
(2) May not be placed on the market in semi-finished products or articles, or parts thereof, if the concentration of
PFOS is equal to or higher than 0.1 % by mass calculated with reference to the mass of structurally or
microstructurally distinct parts that contain PFOS or, for textiles or other coated materials, if the amount of PFOS
is equal to or higher than 1μg /m² of the coated material.
Remark: The result(s) of specimen is/are of the total weight of wet sample.
Sample photo:
*** End of Report ***
SHENZHEN DUOXIN INDUSTRIAL CO.,LTD
CHINA

Date of Sample Received : 13 Jan 2009
Testing Period : 13 Jan 2009 - 16 Jan 2009
SGS-CSTC Ltd.
Test Results:
Green liquid :Description for specimen 1
Heavy metal(s)
Cadmium (Cd) N.D.mg/kg 2IEC 62321/2nd CDV (111/95/CDV), ICP-OES
Lead (Pb) N.D.mg/kg 2IEC 62321/2nd CDV (111/95/CDV), ICP-OES
Mercury (Hg) N.D.mg/kg 2IEC 62321/2nd CDV (111/95/CDV), ICP-OES
Hexavalent Chromium (CrVI) by
Note:
Flame Retardants
Monobromobiphenyl mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Dibromobiphenyl mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Tribromobiphenyl mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Tetrabromobiphenyl mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Pentabromobiphenyl mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Hexabromobiphenyl mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Heptabromobiphenyl mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Octabromobiphenyl mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Nonabromobiphenyl mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Decabromobiphenyl mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Sum of PBDEs mg/kg - N.D. -
Monobromodiphenyl ether mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Dibromodiphenyl ether mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Tribromodiphenyl ether mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Tetrabromodiphenyl ether mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Pentabromodiphenyl ether mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Hexabromodiphenyl ether mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Heptabromodiphenyl ether mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Octabromodiphenyl ether mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Nonabromodiphenyl ether mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Decabromodiphenyl ether ## mg/kg IEC 62321/2nd CDV (111/95/CDV), GC-MS N.D. 5
Note:
4. "-" = Not regulated
5. ## = The exemption of DecaBDE in polymeric application according 2005/717/EC was overruled by the
European Court of Justice by its decision of 01.04.2008. Subsequently DecaBDE will be included in the sum of
PBDE after 01.07.2008
PFOS Perfluorooctane sulfonates
Note:
Reference Information: Directive 2006/122/EC
(1) May not be placed on the market or used as a substance or constituent of preparations in a concentration
equal to or higher than 0.005 % by mass.
(2) May not be placed on the market in semi-finished products or articles, or parts thereof, if the concentration of
PFOS is equal to or higher than 0.1 % by mass calculated with reference to the mass of structurally or
microstructurally distinct parts that contain PFOS or, for textiles or other coated materials, if the amount of PFOS
is equal to or higher than 1μg /m² of the coated material.
Remark: The result(s) of specimen is/are of the total weight of wet sample.
Sample photo:
Test Report No. CANEC0805560801 Date: 17 Oct 2008 Page 1 of 4
SHEN ZHEN XIN KAI HUI METAL MATERIAL SALES DEPARTMENT
NO.910,XING HE BUILDING,SHAJING STREET OFFICE,SHAJING TOWN BAO AN AREA,SHEN ZHEN CITY
CHINA
SUS 301
Date of Sample Received : 13 Oct 2008
Testing Period : 13 Oct 2008 - 17 Oct 2008
:Conclusion Based on the performed tests on submitted sample(s), the results comply
with the RoHS Directive 2002/95/EC and its subsequent amendments.
SGS-CSTC Ltd.
Test Results:
Silver-gray metal sheet :Description for specimen 1
RoHS Directive 2002/95/EC
100Cadmium (Cd) N.D.mg/kg 2IEC 62321/2nd CDV (111/95/CDV), ICP-OES
1000Lead (Pb) N.D.mg/kg 2IEC 62321/2nd CDV (111/95/CDV), ICP-OES
1000Mercury (Hg) N.D.mg/kg 2IEC 62321/2nd CDV (111/95/CDV), ICP-OES
#Hexavalent Chromium (CrVI) by
Note:
4. = Spot-Test:
Negative = Absence of CrVI coating, Positive = Presence of CrVI coating;
(The tested sample should be further verified by boiling-water-extraction method if the spot test result
is negative or cannot be confirmed.)
Boiling-water-extraction:
Positive = Presence of CrVI coating; the detected concentration in boiling-water-extraction solution is
equal or greater than 0.02 mg/kg with 50 cm² sample surface area.
5. # = Positive indicates the presence of CrVI on the tested areas.
Negative indicates the absence of CrVI on the tested areas.
6. "- " = Not regulated
Sample photo:
Judgement
()
Note
()
1 B 4.75 4.74 4.72 4.72 4.74 4.73 4.74 4.71 OK
2 C 6.90 6.95 6.91 6.91 6.92 6.88 6.95 6.93 OK
3 C 1.88 1.88 1.85 1.87 1.86 1.87 1.86 1.86 OK
4 C 7.78 7.79 7.81 7.79 7.80 7.77 7.78 7.80 OK
5 B 2.17 2.12 2.15 2.14 2.15 2.15 2.12 2.16 OK
6 B 0.67 0.66 0.66 0.67 0.67 0.68 0.67 0.67 OK
7 B 2.60 2.60 2.59 2.62 2.60 2.61 2.60 2.61 OK
8 C 4.93 4.91 4.95 4.95 4.95 4.92 4.96 4.93 OK

() MICRO USB FEMALE
Sample Q'ty.
() 8PCS
Plug guage() F:Other()
1,5
2,4
1,31,3
C
TYPE)
PERFORMANCE TEST REPORT TD-CN457S030R-1
2008/4/14
Component source
mastery(): ) Other():
Test Group()
product
A - 1 / 4
C h e c k e d b y ( ) :
I n s p e c t e d b y ( ) :
In su la ti on R es is ta nc e
3 I n i t i a l : 1 0 0 M Ω
M i n i m u m

0% 3/
5 5
Co nn ec to r Ma ti ng F or ce
3 5
Ne wt
Ma xi mu m
Vo lt ag e
fl as ho ve r& sp ar ko ve r&
ex ce ss
0% 3/
5 D
ie le
ct ric
W ith
st an
di ng
V ol
ta ge
.T es
te r
EI A 36 4- 21 T es t vo lt ag e 50 0V D C be tw ee n
ad ja ce nt c on ta ct s of m at ed a nd u nm at ed
co nn ec to r as se mb li es .
In su
la tio
n R
es is
ta nc
e Te
st er
1 Ap pe ar an ce
No d ef ec ts t ha t wo ul d
im pa ir n or ma l
op er at io ns .
M ic
ro -o
hm M
et er
Co nt ac t re si st an ce
In it ia l: 30 m Ω
Ma xi mu m
EI A 36 4- 23 S ub je ct m at ed c on ta ct s as se mb le d in
ho us in g to 2 0m V ma xi mu m op en c ir cu it a t 10 0 mA
ma xi mu m.
Th e di st an ce f ro m th e sa mp le f or 3 0~ 40 C M;
Li gh t fl ux i s 50 0~ 90 0 lu x;
In sp ec t an gl e is 3 0~ 60 °.

Te st
R ea
so ns
(

T A K E W I N G T E C H N O L O G Y C O . , L T D .
P E R F O R M A N C E T E S T R E P O R T
Te st
S ta
Pl as
tic M
at er
ia l
(

N e w P r o d u c e V a l i d a t e (

)
A b n o r m a l Q u a l i t y V a l i d a t e (

)
N o r m a l Q u a l i t y V a l i d a t e (
)
P u r c h a s e
P r o d u c t V a l i d a t e (

) : )
T h e p r o d u c t c r e d i b i l i t y t e s t

) :
) (
) :
S e l f - m a s t e r y (
) : )
) (
) :
) :
) (
) :
) : )
) :
)
PA SS
PA SS
PA SS
EI A 36 4- 20 ( or M IL -S TD -2 02 F, M et ho d 30 1, T es t
Co nd it io n B) 10 0 V AC f or o ne m in ut e at s ea
le ve l
Le ak ag e cu rr en t: 0 .5 mA M ax im um
EI A 36 4- 13 S ha ll b e me as ur ed w it h TE NS IO N GA UG E
or T EN SI ON T ES TE R. Me as ur e fo rc e ne ce ss ar y to
ma te a ss em bl ie s at m ax im um r at e of 1 2. 5m m (o r
0. 49 2
M at
in g
A nd
U nm
at in
g Fo
rc e
Te st
er
T e s t e d b y
A - 2 / 4
C h e c k e d b y ( ) :
C on
ta ct
M at
er ia
l (

Pl as
tic M
at er
ia l
(

) (
) :
) : )
) (
) :
) :
) (
) :
) : )
) :
Ma xi mu m

8 Co nn ec to r Ma ti ng F or ce
A m
bi en
er
T e s t e d b y
3/ 10
0% 3/
In it ia l :
re qu ir em en t, s ho w no
ph ys ic al d am ag e.
D ur
ab ili
ty te
st er
0% 3/
In it ia l :
)


)

)
)
P u r c h a s e

) : )

) :
) 25
R
%

Sa m
pl e
na m
e (

A - 3 / 4
C h e c k e d b y ( ) :
58 %
13 Ap pe ar an ce
im pa ir n or ma l
op er at io ns .

Vo lt ag e
fl as ho ve r& sp ar ko ve r&
ex ce ss
0% 11
In su la ti on R es is ta nc e
A f t e r t e s t : 1 0 0 M Ω
M i n i m u m
In su
la tio
n R
es is
ta nc
e Te
st er
PA SS
PA SS
N ot
e (
Af te r te st : 40 m Ω
Ma xi mu m
)
EI A 36 4- 23 S ub je ct m at ed c on ta ct s
as se mb le d in h ou si ng t o 20 mV m ax im um o pe n
ci rc ui t at 1 00 m A ma xi mu m.
Te st
R ea
so ns
(

) (
) :
) : )
) (
) :
) :
) (
) :
) : )
) :


)

)
)
P u r c h a s e

) : )

) :
Pl as
tic M
at er
ia l
(

0

Ju dg
em en
t (
)
)
T e s t e d b y
EI A 36 4- 21 T es t vo lt ag e 50 0V D C be tw ee n
E IA 3 64 -2 0 (o r MI L- ST D- 20 2F , Me th od 3 01 ,
T es t Co nd it io n B) 10 0 V AC f or o ne m in ut e
at s ea l ev el
Le ak ag e cu rr en t: 0 .5 mA M ax im um
D ie
le ct
ric W
ith st
an di
ng V
ol ta
ge .T
es te
5
C h e c k e d b y ( ) :

0. 85
0. 85
0. 85
28 .0
)

)

)
)
P u r c h a s e

) : )

) :
) (
) :
) : )
) (
) :
) :
) (
) :
) : )
) :
Pl as
tic M
at er
ia l
(

) A
C S

T e s t e d b y
PA SS
PA SS
PA SS
PA SS
24 .1
5 24
.2 2
25 .0
9 24
.2 2
22 .9
7 23
.4 7
23 .0
2 23
.4 7
23 .4
6 23
.6 8
23 .0
8 23
.8 5
23 .6
B - 1 / 2
C h e c k e d b y ( ) :
I n s p e c t e d b y (
) :
Th e di st an ce f ro m th e sa mp le f or 3 0~ 40 C M; L ig
h t
.
60 °.
Sa m
pl e
na m
e (
3/ 5

Su bj
ec t
ma te
d co
nn ec
to rs
t o

B - 2 / 2
C h e c k e d b y ( ) :
) :
24 .3
8 24
.2 2
23 .5
8 24
.2 5
26 .1
3 24
.6 5

Sa m
pl e
na m
e (

C - 1 / 2
C h e c k e d b y ( ) :
T e s t e d b y

In su la ti on
Re si st an ce T es te r
Di el ec tr ic
Wi th st an di ng
Vo lt ag e. Te st er
Sa m
pl e
na m
e (

) 20
Pl as
tic M
at er
ia l
(

)

)

)
)
P u r c h a s e

) : )

) :
) (
) :
) : )
) (
) :
) :
) (
) :
) : )
) :
/
3
)
EI A 36 4- 21 T es t vo lt ag e 50 0V /D C be tw ee n
2 In su la ti on
Re si st an ce
I n i t i a l : 1 0 0 M Ω M i n i m u m
1 Ap pe ar an ce
No d ef ec ts t ha t wo ul d im pa ir
no rm al o pe ra ti on s.
Th e di st an ce f ro m th e sa mp le f or 3 0~ 40
CM ;
3/ 6
PA SS
0% 3/
Vo lt ag e
10 0 V AC f or o ne m in ut e at
se a le ve l
1 ). No f la sh ov er o r
in su la ti on b re ak do wn
2) .L ea ka ge c ur re nt : 0. 5m A
Ma xi
mu m.
EI A 36 4- 20 ( or M IL -S TD -2 02 F, M et ho d 30 1,
Te st C on di ti on B )A pp ly a v ol ta ge 1 00 V AC
fo r 1 mi nu te b et we en a dj ac en ts T er mi na ls
an d be tw ee n te rm in al s to g ro un d
4 Hu mi di ty
EI A 36 4- 31 , Te st C on di ti on A M et ho d II I,
(o r MI L- 20 2F , Me th od 1 03 B Te st C on di ti on
B. )- 10 ~6 5


Te st er
Th er ma l Sh oc k
1 ) . S h a l l m e e t v i s u a l r e q u i r e m e n t ,
s h o w n o p h y s i c a l d a m a g e . 2 ) . S h a l l
m e e t r e q u i r e m e n t s o f a d d i t i o n a l
t e s t s a s s p e c i f i e d i n T E S T
S E Q U E N C E i n S e c t i o n 5
EI A 36 4- 32 , Te st C on di ti on I , (o r MI L-
20 2F , Me th od 1 07 G Co nd it io n A. )
S ub je ct m at ed c on ne ct or s to t en c yc le s
be tw ee n – 55
t o +8 5 .
Re si st an ce T es te r
Fa ul
t ra
te (

/
)
EI A 36 4- 21 T es t vo lt ag e 10 0V /D C be tw ee n

Sa m
pl e
na m
e (

) 20
Pl as
tic M
at er
ia l
(

)

)

)
)
P u r c h a s e

) : )

) :
) (
) :
) : )
) (
) :
) :
) (
) :
) : )
) :
Re si st an ce
A f t e t t e s t : 1 0 0 M Ω
M i n i m u m
PA SS
In sp
ec tio
n ST
D (

Vo lt ag e
10 0 V AC f or o ne m in ut e at
se a le ve l
1 ). No f la sh ov er o r
in su la ti on b re ak do wn
2) .L ea ka ge c ur re nt : 0. 5m A
Ma xi
mu m.
PA SS
0% 3/
10
EI A 36 4- 20 ( or M IL -S TD -2 02 F, M et ho d 30 1,
Te st C on di ti on B )A pp ly a v ol ta ge 1 00 V AC
fo r 1 mi nu te b et we en a dj ac en ts T er mi na ls
an d be tw ee n te rm in al s to g ro un d
Di el ec tr ic
Wi th st an di ng
Vo lt ag e. Te st er
8 Ap pe ar an ce
I n s p e c t e d b y ( )
C h e c k e d b y (
) :

CM ;
N ot
e(

D - 1 / 1
.). 2.
, 10

95
) 20
Pl as
tic M
at er
ia l
(

)

)

)
)
P u r c h a s e

) : )

) :
) (
) :
) : )
) (
) :
) : )
) (
) :
) : )
) :
/
1 Ap pe ar an ce
im pa ir n or ma l op er at io ns .
Vi su al iz at io n
Li gh t fl ux i s 50 0~ 90 0 lu x; In sp ec t an gl e is
30 ~6 0° .
2 So ld er ab il it y
MI CR O Us b co nt ac t so ld er
ta il s sh al l pa ss 9 5%
co ve ra ge a ft
er o ne h ou r
st ea m ag in g as s pe ci fi ed i n
ca te go ry 2 .
0% IA 3 64 -5 2 Af te r on e ho ur s te am a gi ng .
T he o bj ec t of t es t pr oc ed ur e is t o de ta il a
un fi rm t es t me th od s fo r de te rm in in g
3/ 6
PA SS
im pa ir n or ma l op er at io ns .
Vi su al iz at io n
30 ~6 0° .

N ot
e(

C h e c k e d b y ( ) :

T e s t e d b y
E - 1 / 1
er at io ns .
30 ~6 0° .
Te st
E qu
ip m
en t
M a t i n g A n d
Un m a t i n g F o r c e
T e s t e r
Te st
c on
di tio
)
30 ~6 0° .
EI A 36 4- 35 Sh al l be m ea su re d wi th T EN SI ON
GA UG E or T EN SI ON T ES TE R in s am e di re ct io n.
Vi s u a l i z a t i o n
PA SS
Pi n
ag e(
) 2
U N
Mo ld in g
S a m p l e 2
S a m p l e 3
Vi s u a l i z a t i o n
S a m p l e 4
1 Ap pe
mi ni
mu m
Fa ul
t ra
te (

ua li ty Va li da te (

) N o r m a l Q u a l i t y V a l i d a t e ( ) P u r ch a s e P r o d u c t
Va li
da te
):
)
T he p ro du ct c re di bi li t y te st

C om
po ne
nt so
ur ce
):
) (
P u r c h a s e ( ) : S e l f - m a s t e r y( ) : )
Sh
): )
) 20
C S

PE R
FO R
M A
N C
E TE
ST R
EP O
R T
C h e c k e d b y ( ) :
) :

T e s t e d b y
Pi n
F - 1 / 2
C h e c k e d b y ( ) :
T e s t e d b y

No d ef ec ts t ha
t wo ul d
op er at io ns .
Vi su al iz at io n
Th e di st an ce f ro m th e sa mp le f or 3 0~ 40 C M; Li gh t
fl ux i s 50 0~ 90 0 lu x; In sp ec t an gl e is 3 0~ 60 °.
PA SS
0% Co nt ac t re si st an ce
Te st er
No a pp ea ra nc e da ma ge d
co nt ac t re si st an ce :3 0
mΩ M ax .
st re ng th
EI A 36 4- 17 T es t Co nd it io n 3 Me th od A ,
S ub je ct m at ed c on ne ct or s to t em pe ra tu re l if e a t
85 f or 9 6h ou rs
3/ 9
ma xi mu m.
Te st er
Af te r te st :4
0 mΩ
In it ia l: 30 m Ω
ma xi mu m
0% 3/
No d ef ec ts t ha
t wo ul d
op er at io ns .
3/ 6
0% 3/
Te st er
ma xi mu m.
PA SS
Te st
d at
e (

/
)

)

)
)
P u r c h a s e

) : )
T he p ro du ct c re di bi li ty t es t

) :
) (
) :
) : )
) (
) :
) :
) (
) :
) : )
) :
Pl as
tic M
at er
ia l
(

) 20

Sa m
pl e
na m
e (

F - 2 / 2
C h e c k e d b y ( ) :
T e s t e d b y

) 20
/
Pl as
tic M
at er
ia l
(

A m
bi en
)

)

)
)
P u r c h a s e

) : )

) :
) (
) :
) : )
) (
) :
) :
) (
) :
) : )
) :
G - 1 / 1
C h e c k e d b y ( ) :
CM ;
Li gh t fl ux i s 50 0~ 90 0 lu x; In sp ec t an gl e
is 3 0~ 60 °.
Ap pe ar an ce
3 Vi su al iz at io n

So ld er in g H ea t
No m ec ha ni ca l de fe ct o n ho us in g
or o th er p ar ts .
PA SS
So ld er in g H ea t
Te st er
fo r RE FL OW S OL DE RI NG :
EI AJ R CX -0 10 1/ 10 2.
Pr e- he at : 1 50 (M in )~ 20 0( Ma x) ,
6 0 ~1 80 S ec on ds
Te mp er at ur e : 2 60 ± 5
Im me rs io n du ra ti on : 1 0~ 40 s ec .
2
1 Ap pe ar an ce
Vi su al iz at io n
3/ 7
CM ;
Li gh t fl ux i s 50 0~ 90 0 lu x; In sp ec t an gl e
is 3 0~ 60 °.
/
)

)

)
)
P u r c h a s e

) : )

) :
) (
) :
) : )
) (
) :
) :
) (
) :
) : )
) :
Pl as
tic M
at er
ia l
(

) 20

Sa m
pl e
na m
e (

C h e c k e d b y (
) :

A m
bi en
) 20
Pl as
tic M
at er
ia l
(

)

)

)
)
P u r c h a s e

) : )
T he p ro du ct c re di bi li ty t es t

) :
) (
) :
) : )
) (
) :
) :
) (
) :
) : )
) :
PA SS
Te st
d at
e (

/
1 Ap pe ar an ce
im pa ir n or ma l
op er at io ns .
4/ 11
0% 4/
Te st er
ma xi mu m.
si st an ce
ma xi mu m
si st an ce
ma xi mu m
4 Vi br
at io n
No d is co nt in ui ti es o f
1 mi cr os ec on d or l on g
du ra ti on . Se e no te
EI A- 36 4- 28 D
Su bj ec t ma te d co nn ec to rs t o 10 ~5 5~ 10 Hz t ra ve rs ed
in 1 m in ut e at 1 .5 2m m am pl it ud e 2 ho ur s ea ch o f
3 mu tu al ly p er pe nd ic ul ar p la ne s.
4/ 13
ma xi mu m.
4/ 12
6 Ap pe ar an ce
im pa ir n or ma l
op er at io ns .
Vi su al iz at io n
Th e di st an ce f ro m t he s am pl e fo r 30 ~4 0 CM ;L ig ht
fl ux i s 50 0~ 90 0 lu x; In sp ec t an gl e is 3 0~ 60 °.
T e s t e d b y

0% Co nt ac t re si st an ce
Te st er
3 Me ch an ic al S ho ck
No d is co nt in ui ti es o f
1 mi cr os ec on d or l on g
du ra ti on . Se e no te
EI A- 36 4- 27 B
Su bj ec t ma te d co nn ec to r to 5 0G s ha lf -s in e
sh oc k pu ls es o f 11 ms ec d ur at io n. T hr ee s ho ck s in
ea ch d ir ec ti on a pp li ed a lo ng t hr ee m ut ua ll
pe rp en di cu la r pl an ed f or a t ot al o f 18 s ho ck s
Me ch an ic al
Sh oc kT es te r
PA SS
LCP_MSDS.pdf