8/3/2019 Resume de Cours Cisco

1/5

Router>enable

Router#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#interface Serial0/1/1

Router(config-if)#no shutdown

Router(config-if)#ip address 199.6.13.2 255.255.255.0

Router(config-if)#

Router(config-if)#exit

Router(config)#interface FastEthernet0/0

Router(config-if)#

Router(config-if)#exit

Router(config)#interface FastEthernet0/1

Router(config-if)#

Router(config-if)#exit

Router(config)#interface Serial0/1/0

Router(config-if)#

Router(config-if)#exit

Router(config)#interface Serial0/1/1

Router(config-if)#

Router(config-if)#exit

Router(config)#interface Serial0/1/0

Router(config-if)#ip address 204.204.7.1 255.255.255.0

Router(config-if)#no shutdown

Router(config-if)#

8/3/2019 Resume de Cours Cisco

2/5

%LINK-5-CHANGED: Interface Serial0/1/0, changed state to up

clock rate 64000

Router(config-if)#

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0, changed state to up

Router(config-if)#exit

Router(config)#interface FastEthernet0/0

Router(config-if)#no shutdown

Router(config-if)#

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

ip address 223.8.151.1 255.255.255.0

Router(config-if)#

Router(config-if)#exit

Router(config)#interface Serial0/1/1

Router(config-if)#

%LINK-5-CHANGED: Interface Serial0/1/1, changed state to up

Router(config-if)#exit

Router(config)#router rip

Router(config-router)#network 199.6.13.0

Router(config-router)#network 223.8.151.0

Router(config-router)#network 204.204.7.0

Router(config-router)#

8/3/2019 Resume de Cours Cisco

3/5

Router con0 is now available

Router>enable

Router#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#interface Serial0/1/1

Router(config-if)#clock rate 64000

Router(config-if)#

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/1, changed state to up

shutdown

Router(config-if)#

%LINK-5-CHANGED: Interface Serial0/1/1, changed state to administratively down

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/1, changed state to down

Router(config-if)#exit

Router(config)#interface Serial0/1/1

Router(config-if)#

Router(config-if)#exit

Router(config)#interface Serial0/1/0

Router(config-if)#

Router(config-if)#exit

Router(config)#interface FastEthernet0/0

Router(config-if)#

Router(config-if)#exit

Router(config)#interface FastEthernet0/1

Router(config-if)#

Router(config-if)#exit

8/3/2019 Resume de Cours Cisco

4/5

Router(config)#interface Serial0/1/1

Router(config-if)#

Router(config-if)#exit

Router(config)#interface Serial0/1/1

Router(config-if)#

Router(config-if)#exit

Router(config)#interface Serial0/1/0

Router(config-if)#no ip address

Router(config-if)#

Router(config-if)#exit

Router(config)#interface Serial0/1/1

Router(config-if)#

Router(config-if)#exit

Router(config)#interface Serial0/1/1

Router(config-if)#ip address 204.204.7.1 255.255.255.0

Router(config-if)#no shutdown

Router(config-if)#

%LINK-5-CHANGED: Interface Serial0/1/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/1, changed state to up

Router(config-if)#exit

Router(config)#interface Serial0/1/0

Router(config-if)#ip address 199.6.13.2 255.255.255.0

Router(config-if)#no clock rate

Router(config-if)#

Router(config-if)#exit

8/3/2019 Resume de Cours Cisco

5/5

Router(config)#interface Serial0/1/1

Router(config-if)#

Router(config-if)#exit

Router(config)#

Router(config)#ip route 0.0.0.0 0.0.0.0 serial 0/1/0

Router(config)#exit

Router#

%SYS-5-CONFIG_I: Configured from console by console

Router#conf t

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#ip route 0.0.0.0 0.0.0.0 serial 0/1/1

Router(config)#exit

Router#

%SYS-5-CONFIG_I: Configured from console by console

Router con0 is now available

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/1, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/1, changed state to up