Upload
anna-arora
View
120
Download
9
Tags:
Embed Size (px)
DESCRIPTION
Porosity Description and techniques used for calculating it.
Citation preview
RESERVOIR ROCK PROPERTIES
RESERVOIR ROCK P0ROSITY
LECTURE-03
POROSITYStorage capacity of medium An exclusive rock property
Expressed in Fraction or %
Statistical property based on the rock volume*.Used for resave estimate.
Effects hydrocarbon recovery
Part of the total porous rock volume which is not occupied by rock grains or fine mud rock, acting as cement between grain particles.
• If the selected volume is too small the calculated porosity can deviate greatly from the true value
* If the volume is too large the porosity may deviate from the real value due to the influence of heterogeneity.
Physically following types of porosity can be distinguished:
• Inter granular porosity.• Fracture porosity.• Micro-porosity.• Vugular porosity.• Intra granular porosity.
Utility wise following types of porosity can be distinguished:
• Absolute Porosity • Effective Porosity
Characteristics of Porous Media Geometric character of rock
•inter granular – intra granular•fractured.
Mechanical properties of rock•consolidated•unconsolidated
Heterogeneity
Models of Porous Media
1. Represented by Parallel Cylindrical Pores*
Idealized Porous Medium
where r is the pipe radius and m·n is the number of cylinders contained in the bulk volume.12.08.2014
2. Represented by Regular Cubic-Packed Spheres
where Vm is the "matrix“ volume or the volume of bulk space occupied by the rock.
3. Represented by Regular Orthorhombic -Packed Spheres
Where h is the height of the orthorhombic-packed spheres . The matrix volume is unchanged. And thus,
4. Represented by Regular Rhombohedral -Packed Spheres
Where h is the height in the tetrahedron and is given by
5. Represented by Irregular - Packed Spheres with Different Radii
Real reservoir rock exhibits a complex structure and a substantial variation in grain sizes as well as their packing , which results in variation of porosity and other important reservoir properties , often related to the heterogeneity of porous medium.
By drawing a graph with radii of the spheres plotted on the horizontal axis and heights equal to the corresponding frequencies of their appearance plotted on the vertical axis ,one can obtain a histogram of distribution of particles (spheres) in sizes.
EXAMPLE
Porosity: relations/presentationPorosity = x 100Pore volume
Bulk volume
1
2
1
Pore volume, Bulk volume
Bulk volume, Grain volume
Pore volume, Grain volume
Utility limits of porosity• The effective porosity of rocks varies between less than
1% to 40%.• It is often stated that the porosity is:
(a)Low if Φ < 5%(b)Mediocre if 5% < Φ < 10 %(c)Average if 10%< Φ < 20 %(d)Good if 20%< Φ < 30 %(e)Excellent Φ > 30%
Physical Impacts
1. Porosity and hydraulic conductivityNormally Porosity can be proportional to hydraulic conductivity: two similar sandy aquifers, the one with a higher porosity will typically have a higher conductivity **Grain size decreases the proportionality between pore throat radii and porosity begins to fail and therefore the proportionality between porosity and hydraulic conductivity failsExample: Clays typically have very low hydraulic conductivity (due to their small pore throat radii) but also have very high porosities (due to the structured nature of clay)which means clays can hold a large volume of water per volume of bulk material, but they do not release water rapidly as they have low hydraulic conductivity.
2. Sorting and porosityGrains of approximately all one size materials have higher porosity than similarly sized poorly sorted materials which drastically reducing porosity.
3. Consolidation of rocks
Consolidated rocks have more complex porosities Rocks have decrease in porosity with age anddepth of burialThere may be exceptions to this rule, usually because of thermal history.
1. Primary porosity :The original porosity of the system
2. Secondary porosityA subsequent or separate porosity system in a rock, often enhancing overall porosity of a rock. This can be a result of chemical leaching of minerals. This can replace the primary porosity or coexist with it (see dual porosity below).
Types of geologic porosities
3. Fracture porosityThis is porosity associated with a fracture system or faulting.4. Vuggy porosityThis is secondary porosity generated by dissolution of large features (such as macrofossils) in carbonate rocks leaving large holes, vugs , or even caves.5. Open porosityRefers to the fraction of the total volume in which fluid flow is effectively and excludes closed pores .
6. Closed porosityFraction of the total volume in which fluids or gases are present but in which fluid flow can not effectively take place and includes the closed pores.7. Dual porosityRefers to the porosity of two overlapping reservoirs -fractured rock , leaky aquifer results in dual porosity systems.
8. Macro porosityRefers to pores greater than 50 nm* in diameter. Flow through macropores is described by bulk diffusion. 9. Meso porosityRefers to pores greater than 2 nm and less than 50 nm in diameter. Flow through mesopores is described by diffusion.10 Micro porosityRefers to pores smaller than 2 nm in diameter. Movement in micropores is by activated diffusion. * 1.0 × 10-7 centimetres
Measurement of Porosity
Well Logs Core Analysis
In situ Surface
POROSITY DETERMINATIONFROM LOGS
A wire line truck with a spool of logging
cable is setup so that the measuring equipment can be lowered into the wellbore.
The logging tools measure different properties, such as spontaneous potential and formation resistivity, and the equipment is brought to the surface.
The information is processed by a computer in the logging vehicle, and is interpreted by an Formation engineer or geologist.
The basic setup of logging process
Well LogSP Resistivity
OPENHOLE LOG EVALUATION
A decrease in radioactivity from the gamma ray log could indicate the presence of a sandstone formation. An increase in resistivity may indicate the presence of hydrocarbons. An increase in a porosity log might indicate that the formation has porosity and is permeable.
Interpretation
Oil sand
Gammaray
Resistivity Porosity
Increasingradioactivity
Increasingresistivity
Increasingporosity
Shale
Shale
POROSITY DETERMINATION BY LOGGING
POROSITY LOG TYPES•Bulk density
•Sonic (acoustic)• Compensated neutron
• Formation lithology • Nature of the Fluid in pores.
Essential Requirements
Density log, the neutron log*, and the sonic logs do not measure porosity. Rather, porosity is calculated from measurements such as electron density, hydrogen index and sonic travel time.* A precallibrated Neutron log directly provides limestone porososity in carbonates.
CORES• Allow direct measurement of reservoir properties• Used to correlate indirect measurements, such as wire line/LWD
logs• Used to test compatibility of injection fluids• Used to predict borehole stability• Used to estimate probability of formation failure and sand
production
► Following equation is used:
► On a sample of generally simple geometric form, two of the three values Vp , Vs and VT are therefore determined.
►The standard sample (plug) is cylindrical, Its cross section measures about 4 to 12 cm2 and its length is varies between 2 to 5 cm.
►The plugs are first washed and dried.►The measuring instruments are coupled to microcomputers to
process the results rapidly.
Φ
ESTIMATING POROSITY FROMCORE ANALYSIS
A. Measurement of VT
The apparatus has a frame C connected by a rod to a float F immersed in a beaker containing mercury.A reference index R is Fixed to the rod. A plate B is suspended from the plate.(a) First measurement: the sample is placed on plate B with a weight P1 to bring R in,in contact with the mercury. (b) Second measurement: the sample is placed under the hooks of float F, and theweight P2 is placed on plate B to bring R in to contact with the mercury. If ρHg is the density of mercury at measurement temperature. Then:
(a) Measurement of the buoyancy exerted by mercury on the sample immersed in it
APPARATUS
VT
VT
Method: Without a sample using the piston,mercury is pushed to mark, indicated on the reference valve (V).The vernier of the pump is set at zero.With the sample in place, the mercury is again pushed to samemark. The vernier of the pump is read and the volume VT isobtained. The measurement is only valid if mercury does notpenetrate into the pores. The accuracy is ± 0.01 cm3.
(b) Use of positive displacement pump VT
M
(c) Measurement:The foregoing methods are unsuitable if the rock contains fissures or macro pores, because mercury will penetrate into them.Here a piece of cylindrical core’s diameter “d” and height “h” can be measured using sliding caliper:
B. Measurement of VS
Measurement of the buoyancy exerted on the sample by a solvent with which it is saturated. VS by immersion method
The method is most accurate but difficultand time consuming to achieve completesaturation. The operations are normallystandardized. The difference between the weights of sample in air (P air)and the solvent in which it is immersed (P immersed) gives
VS as :
Regardless of specific apparatus used i.e. singe cell or doublechamber, the sample is subjected to known initial pressure bygas, which was originally at atmospheric pressure.The pressure is then changed by varying the volume of gas inchamber.The variation in volume and pressure are measured by usingBoyle’s law.
P1 V1 = P2 V2 The equipments using single cell and double are shown innext slide.
(b)Use of compression chamber and Boyle’ law
1 is chamber for core2 is constant volume chamber3 is core 4 & 5 is pressure manometers6 is source of gas
1 is chamber for core2 is core3 is volume plunger4 is pressure gauge
Use of compression chamber and Boyle’ law
Use of single cell Use of double cell
1
2
3
4,5
62
4
3
1
b. Measurement by weighing a liquid filling the effective pores
This liquid is often brinec. Measurement by mercury injectionIn this case the mercury never totally invade the interconnected pores. Hence the value obtained for the parameter is under par.
a. Measurement of air in the pores The mercury positive displacement pump is used for this purpose. After measuring VT ,the valve of the sample core holder is closed and the air in the interconnected pores is expanded. The variation in volume and pressure are measured using Boyle’s law
C. Determination of VP
Fluid Summation Method• The method involves the analysis of a FRESH sample containing
water, oil and gas.• The distribution of these fluids is not the same as in the reservoir.
because the core has been invaded by the mud filtrate and decomposed when pulled out.
• Still/but the sum of the volumes of these three fluids, for a unit volume of rock, gives the effective porosity of the sample.
• The total volume is determined by mercury displacement pump.
(1) VP = Vw + VO + VG
(2) Sw + SO + SG = 100%
Sw = Vw/ VP SO = Vo/ VP SG = VG/ VP
Special Method :Determination of VP
Relation of Fluid Summation and porosity
ELECTRICAL METHODFormation Resistivity Factor
Formation Resistivity Factor : is the ratio of the resistivity of clean formation(core sample) fully saturated with brine to the resistivity observed with brine solution of same salinity. i.e.
F.F. = Ro / Rw
WhereRo= Resistivity of clean formation sample fully saturated with brine of specific salinity, Rw= Resistivity of brine of same salinity
(without core)
1
Formation Resistivity Factor : is also related to the POROSITY by Archie Equation given as under:
FF = a/Φm
Wherea = Tortuosity Factor (Path Complexity)m= Cementation Factor (Grain Size)Higher is the value of ‘a’ higher is
the value of ‘m’ .
2
a
m
Formation Resistivity Factor : is also greatly effected by over burden pressure and in turn with POROSITY.
3
POROSITY AVERAGING
If the Bedding planes show large variations in porosity vertically then arithmetic average porosity
The thickness - weighted average porosity is used to describe the average reservoir porosity. If porosity in one portion of the reservoir to be greatly different from that in another area due to sedimentation conditions, the areal weighted average
The volume-weighted average porosity is used to characterize the average rock porosity.
1
3
4
2
averaging techniques are expressed mathematically in the following forms: Arithmetic average Thickness-weighted average Areal-weighted average Volumetric-weighted average
MATHEMATICAL EXPRESSIONS
POROSITY APPLICATIONS
APPLICATION OF EFFECTIVE POROSITY
For a reservoir with an areal extent of A acres and an average thickness of h feet
Bulk volume = 43,560 Ah, ft3 OR = 7,758 Ah, bbl
The reservoir pore volume PV in cubic feet : PV = 43,560 AhФ, ft3
The reservoir pore volume PV in bbl is given as : PV = 7,758 AhФ, bbl
Porosity Distribution (Histogram)The multiple sampling of porosity measurements for reservoir rocks at different depths and in different wells gives a data set that can then be plotted as a histogram , to reveal the porosity’s Frequency distribution. Such histograms may be constructed separately for the individual zones, or units, distinguished within the reservoir, and thus give a good basis for statistical estimates (mean porosity values, standard deviations, etc.).
APPLICATION
1. Zone Analysis
Histogram
Simulation of fluid flow in porous media, require a realistic picture of the rock porosity
The grouping of porosity data according to the reservoir zones, depth variation or graphical co-ordination, yield spatial trends.
2. Reservoir Simulation
Trends of porosity distribution in the depth profiles of two reservoir sand stone.
Mechanical digenesis (compaction)/ chemical digenesis (cementation) have a profound effect on a sedimentary rock’s porosity. This burial effect is illustrated by the two typicalExamples of sand and clay deposits,
3. Sediment compaction
Development of a bulk and realistic picture of the reservoir to evaluate -Early Reserves Estimates Exploration leads Expected Recoveries, well treatments , IOR and EOR
Boundaries of Sand ridges are shown as separate units / porosity zones - numbered as zone 1 , zone2, zone3 and zone 4,indicating their areal extent.
4. Exploration leads
REMARKS
Rock at reservoir conditions is subject to overburden pressure stresses, while the core recovered at surface tends to be stress relived; therefore laboratory determined porosity values are generally expected to be higher than in-situ values. If ΦR represent porosity at reservoir condition, ΦL be porosity at reservoir condition, rock compressibility as Cp (V/V/psi) and net overburden pressure as ∆PN ( over burden pressure – fluid pressure) psi; then we may use the following relation:
ENGINEERINGUPES
DEHRADUN
LECTURE-03 A
RESERVOIR
POROSITYROCK
EXERCISES
The grain volume of rock sample of 1.5” dia and 5.6 cm length was found to be 56.24 cc and bulk volume of the sample using mercury displacement method was measured 73.80 cc. If dry weight of the sample is149.88 gms, find the grain density. Calculate the pore volume and porosity of the sample.
Example 1
SOLUTION -1
*Pore volume = Bulk volume-Grain volume =73.80 – 56.24=17,56 cc
*Porosity,% =(Pore volume/bulk volume) x 100
=(17.56/73.80)X100 = 23.79%*Grain density=Dry weight of sample/Grain
volume = 149.88/56.24
= 2.665 gms/cc
Example-2
Weight of the dry sample in air is 20.0gms. The weight of the sample when saturated with water is 22.5gms.Weight of saturated sample in water at 40 degree F is 12.6 gms.Find the Bulk volume.
SOLUTION-2
Weight of the water displaced = 22.5- 12.6= 9.9gmsVolume of water displaced=9.9/1= 9.9ccWill be the bulk volume of the sample.
Example-3
A core sample immersed in water has its weight in air as 20gmsDry sample when coated with paraffin weighs 20,9 gms (density of paraffin being 0.9gm/cc).If weight of the immersed sample in water at 40 ºF be given as 10 gms.Find the bulk volume of core sample.
SOLUTION -3Weight of the paraffin=20.9-20.0=0.9gmsVolume of paraffin=0.9/0.9=1ccWeight of water displaced=20.9-10.0 =10.9gmsVolume of water displaced= 10.9/1.0 =10.9ccTherefore bulk volume of rock will be:Volume of water displaced – volume of paraffin=10.9-1=9.9cc
EXAMPLE- 4
Determine the total porosity of sample when the grain density is 2.67 gms/cc.Weight of the dry sample in air is 20 gms.Bulk volume of the sample is 9.9cc
SOLUTION -4*Grain volume of the sample
= Weight of dry sample in air/Sand density =7.5
* Total porosity= (Bulk volume-grain volume)/Bulk
volume X 100 =(9.9 – 7.5)/ 9.9 X 100 = 24.2%
Example -5
Calculate the weight of 1 m3 of Sand stone of 14% porosity.Given that the sand density is 2.65 gm/cm3
Volume of sand stone BVs=1m3
PorosityΦ(PV) =14% Density of sand grains=2.65. BV= PV + GV GV = BV - PV = 1- 0.14 = 0.86 m3
Ws = Density of sand grains x GV =2.65gm/cm3 x 0.86 x 106gm =2.279 x 106gm
SOLUTION-5
Example-6
A petroleum reservoir has an areal extent of 20,000 ft2 and a pay thickness of 100ft.The reservoir rock has a uniform porosity of 35%. Find the pore volume of this reservoir
Pore volume = 7758 AhΦ bbl. =7758 x 20,000 x 100 x 35/100=54306 x 105 bbl.
SOLUTION - 6
Example – 7 An oil reservoir exists at its bubble-point pressure of 3000 psia and temperature of 160°F. The oil has an API gravity of 42° and gas-oil ratio of 600 scf/STB. The specific gravity of the solution gas is 0.65. The following additional data are also available• Reservoir area = 640 acres• Average thickness = 10 ft• Connate water saturation = 0.25• Effective porosity = 15%Calculate the initial oil in place in STB.
SOLUTION - 7Step 1. Determine the specific gravity of the stock-tank oil as 0.8156
Step 2. Calculate the initial oil formation volume factor as 1.306 bbl /STB
Step 3. Calculate the pore volume = 7758 (640) (10) (0.15) = 7,447,680 bbl
Step 4. Calculate the initial oil in place Initial oil in place = 12,412,800 (1 - 0.25)/1.306 = 4,276,998 STB
Example 8 Calculate the arithmetic average and thickness-weighted average from the following measurements
Solution -8
Porosity = void volume ÷ soil volumePorosity = 0.3 cubic meters ÷ 1.0 cubic meters
Porosity = 0.3
LECTURE-03 B
ROCKPOROSITY
DENSITY LOGS
• Radioactive source is used to generate gamma rays• Gamma ray collides with electrons in formation, losing
energy• Detector measures intensity of back-scattered gamma
rays, which is related to electron density of the formation
1Electron density is a measure of bulk density
GRAPI0 200
CALIXIN6 16
CALIYIN6 16
RHOBG/C32 3
DRHOG/C3-0.25 0.25
4100
4200
DENSITY LOG
Caliper
Density correction
Gamma ray Density
DENSITY LOGS: PRINCIPLEBulk density, b, is dependent upon:
• Lithology
• Porosity
• Density and saturation*of fluids in pores
* Saturation is fraction of pore volume occupied by a particular fluid
BULK DENSITYBulk density varies with lithology–Sandstone 2.65 g/cc–Limestone 2.71 g/cc–Dolomite 2.87 g/cc
fmab 1
MatrixFluids in
flushed zone
POROSITY FROM DENSITY LOGPorosity equation
xohxomff S1S
fma
bma
Fluid density equation
mf is the mud filtrate density, g/cc
h is the hydrocarbon density, g/cc
Sxo is the saturation of the flush/zone, decimal
Fluid density (f) is between 1.0 and 1.1.If gas is present, the actual f will be < 1.0 and the calculated porosity will be too high.
Where
Formation (b)
Long spacing detector
Short spacing detector
Mud cake(mc + hmc)
Source
Actuality
1. Minimizing the influence of the mud column
Efficiency
i) Source and detector, mounted on a skid, are shieldedii) The openings of the shields are applied against the wall of the borehole by means of an eccentering arm
2. A correction for due to mal instrument contact and formation or roughness of the borehole wall The use of two detectors is advisable to over come this problem.3. Account for all of the effects of borehole breakouts, washouts, and rugosity
Working equation (hydrocarbon zone)
b = Recorded parameter (bulk volume)
Sxo mf = Mud filtrate component
(1 - Sxo) hc = Hydrocarbon component
Vsh sh = Shale component
1 - - Vsh = Matrix component
DENSITY LOGS
• If minimal shale, Vsh 0
• If hc mf f, then
•b = f - (1 - ) ma
fma
bmad
d = Porosity from density log, fractionma = Density of formation matrix, g/cm3
b = Bulk density from log measurement, g/cm3
f = Density of fluid in rock pores, g/cm3
hc = Density of hydrocarbons in rock pores, g/cm3
mf = Density of mud filtrate, g/cm3
sh = Density of shale, g/cm3
Vsh = Volume of shale, fractionSxo = Mud filtrate saturation in zone invaded by mud filtrate, fraction
GRC0 150
SPCMV-160 40ACAL
6 16
ILDC0.2 200
SNC0.2 200
MLLCF0.2 200
RHOC1.95 2.95
CNLLC0.45 -0.15
DTus/f150 50
001) BONANZA 1
10700
10800
10900
BULK DENSITY LOG: EXAMPLE
Bulk DensityLog
RHOC1.95 2.95
NEUTRON LOG2Uses a radioactive source to bombard the formation with neutrons
For a given formation, amount of hydrogen in the formation (i.e. hydrogen index) impacts the number of neutrons that reach the receiverA large hydrogen index implies a large liquid-filled porosity (oil or water)TOOL
PRINCIPLE• Logging tool emits high energy neutrons into
formation.
• Neutrons collide with nuclei of formation’s atoms
• Neutrons lose energy (velocity) with each collision of hydrogen atom.
• The most energy is lost when colliding with a hydrogen atom nucleus
• Neutrons are slowed sufficiently to be captured by nuclei.
• Capturing nuclei become excited and emit gamma rays
ACTIVITIES1. Depending on type of logging tool either
gamma rays or non-captured neutrons are recorded
2. Log records porosity based on neutrons captured by formation
3. If hydrogen is in pore space, porosity is related to the ratio of neutrons emitted to those counted as captured
Neutron log reports porosity, calibrated assuming calcite matrix and fresh water in pores, if these assumptions are invalid we must correct the neutron porosity value
REMARKS
Theoretical equation
where = True porosity of rockN = Porosity from neutron log
measurement, fractionNma = Porosity of matrix fractionNhc = Porosity of formation saturated with
hydrocarbon fluid, fractionNmf = Porosity saturated with mud filtrate,
fractionVsh = Volume of shale, fractionSxo = Mud filtrate saturation in zone
invaded by mud filtrate, fraction
GRC0 150
SPCMV-160 40ACAL
6 16
ILDC0.2 200
SNC0.2 200
MLLCF0.2 200
RHOC1.95 2.95
CNLLC0.45 -0.15
DTus/f150 50
001) BONANZA 1
10700
10800
10900
POROSITY FROM NEUTRON LOG
NeutronLog
CNLLC0.45 -0.15
EXAMPLE
lithology is sandstone or dolomite
ACOUSTIC (SONIC) LOGThese logs are usually borehole compensated (BHC) where in effects at hole size changes as well as errors due to sonde tilt is substantially reduced..system uses two transmitters, one above and one below a pair of sonic receivers
The travel time elapsed between the sound reaching the receiver is recorded and used for porosity calculations.
3
Upper transmitter
Lower transmitter
R1
R2
R3
R4
ACOUSTIC (SONIC) LOG:TOOL
• Tool usually consists of one sound transmitter (above) and two receivers (below)
• Sound is generated, travels through formation
• Elapsed time between sound wave at receiver 1 vs receiver 2 is dependent upon density of medium through which the sound traveled.
When one of the transmitters is pulsed, the sound wave enters the formation, travels along the wellbore and triggers both of the receivers; the time elapsed between the sound reaching each receiver is recorded.
Since the speed of sound in the sonic sonde and mud is less than that in the formations, the first arrivals of sound energy the receivers corresponds to the sound-travel paths in the formation near the borehole wall. The transmitters are pulsed alternately, and the differential time or delta t readings are obtained and averaged. This leads the tool is compensated for tilt.
BHC METHODOLOGY
Lithology Typical Matrix TravelTime, tma, sec/ft
Sandstone 55.5Limestone 47.5Dolomite 43.5Anydridte 50.0Salt 66.7
COMMON LITHOLOGY MATRIXTRAVEL TIMES USED
MODIFICATION
• If Vsh = 0 and if hydrocarbon is liquid (i.e. tmf tf), then
•tL = tf + (1 - ) tma or
maf
maLs tt
tt
s = Porosity calculated from sonic log reading, fractiontL = Travel time reading from log, microseconds/fttma = Travel time in matrix, microseconds/fttf = Travel time in fluid, microseconds/ ft
DTUSFT140 40
SPHI%30 10
4100
4200
GRAPI0 200
CALIXIN6 16
EXAMPLE: ACOUSTIC (SONIC) LOG
Sonic travel time
Sonic porosity
Caliper
Gamma Ray
SONIC LOG:TIME RESPONSEThe response can be written as follows:
fmalog t1tt
maf
ma
tttt
log
tlog = log reading, sec/ft
tma = the matrix travel time, sec/ft
tf = the fluid travel time, sec/ft
= porosity
Sonic log - measures the slowness of a compressional wave to travel in the formation. Matrix travel time (tma) is a function of lithology
SONIC LOG CHARACTERISTICS
There are several more sophisticated sonic logs that couple/ determine both the shear wave arrival and the compressional wave arrival.
This log analyst can determine rock properties such as Poisson’s ratio, Young’s modulus, and bulk modulus.
These values are very important when designing hydraulic fracture treatments or when trying to determine when a well may start to produce sand.
SONIC LOG :SPECIALITY
GRC0 150
SPCMV-160 40ACAL
6 16
ILDC0.2 200
SNC0.2 200
MLLCF0.2 200
RHOC1.95 2.95
CNLLC0.45 -0.15
DTus/f150 50
001) BONANZA 1
10700
10800
10900
EXAMPLE: SONIC LOG
SonicLog
DT150 50us/f
FACTORS AFFECTING SONIC LOG RESPONSE
• Unconsolidated formations• Naturally fractured formations• Hydrocarbons (especially gas)• Salt sections
LET IT BE KNOWN
The three porosity logs:• Respond differently to different matrix compositions• Respond differently to presence of gas or light oils
Combinations of logs can: • Imply composition of matrix• Indicate the type of hydrocarbon in pores
GAS EFFECT
•Density - is too high
•Neutron - is too low
•Sonic - is not significantly
affected by gas