REQUEST FOR INFORMATION (RFI) FOR “REPLACEMENT OF DIGITAL MAPPING SYSTEM AT CAMS, DELHI CANTT”

1. The Military Survey branch of DGIS (Army HQ) is planning to replace the old digital mapping system. With a view to identify probable vendors who can undertake the said project the OEMs/Vendors are requested to forward information on the product which they can offer. The parameters/broad specifications of the item are mentioned in the questionnaire attached as Appendix ‘A’. In addition the vendors are requested to furnish details as per proforma at Appendix ‘B’. 2. Apart from the information as per the Appendices the vendors may also forward technical details/product brochures/literature etc pertaining to the item in question. 3. The required information/details may please be forwarded at the following address by 15 Jun 2010.

(a) DIRECTORATE GENERAL OF WEAPONS AND EQUIPMENT (WE-7) GENERAL STAFF BRANCH ROOM NO.538, ‘A’ Wing Sena Bhawan INTEGRATED HQ MoD (ARMY) DHQ PO NEW DELHI-110011 FAX NO. : 0091-11-2379274 E-Mail :

(b) Addl Dte Gen Mil Svy (GSGS) Dte Gen Info Sys General Staff Branch Integrated HQ of Min of Def (Army) EDP Enclave, Roa Tula Ram Marg Delhi Cantt-110010

FAX No. : 011-26146593 E-Mail : (b) Directorate General of Perspective Planning GSQR Cell Room No. 902, ‘A’ Wing Sena Bhawan

Integrated HQ of Min of Def (Army) DHQ PO, New Delhi-110011

FAX No. : 0091-11-23011198 E-Mail :

4. An early response is requested.

Appendix ‘A’

QUESTIONNAIRE

Specifications/Parameters Reply

1. The purpose for which this equipment is needed or in broad outlines the capabilities that are needed.

2. All technical parameters in terms of size, weight, performance, operating environment, power, torque, preservation, utility life, storage, shelf life etc may be specified. 3. All the elements which need to be structured in the costing of the weapons/equipment system (including comprehensive maintenance/product support package.

(a) The Military Svy is modernizing the existing digital mapping facility which is in use for last several years. The existing system clix & NT based have become obsolete and the vendors terminated AMC due to non availability of spare parts. These systems being of low configuration consume considerable time and delays the OP capabilities as they are not fit enough to handle the digital data efficiently. Considering the present technology it is essential and inadvertent to upgrade the digital mapping systems. These new proposed system will increase the technical capabilities of the unit. (b) The new set up of digital mapping system would consists of high end workstation database servers, plotters, scanners and other related accessories alongwith digitization, photogrammetry and image processing, map publication and GIS software for all mapping functionalities. It is to be ensured that these new system will be able to process the existing data efficiently. The expectation to be fulfilled by the purposed configuration are as follows: -

(i) The existing vectorised file in DSM/DVD-1 format should be usable in new system.

(ii) The maps database already created must be usable in new configuration without a need to recreate the data base.

(iii) The new system should be compatible/extendable with the existing data formats with all vector/raster files and GIS database file.

Annexure-1 (attached). The scheme will include comprehensive AMC for three years.

4. ToT feasible or not and time require for the same. 5. Advance intimation for the vendors to obtain requisite government clearances. 6. Estimated cost of the equipment. 7. Any additional features, as applicable, may also be included.

N.A. N.A. Rs.15.00 crore approximately. No.

Annexure-1 1. Workstation for Digitisation, Updation, GIS & Image Processing – 25 Nos. System Specifications

(a) Processor : Dual Processor Intel Xeon Quad Core

3.2 GHz or higher version. (b) RAM : 6 GB or above, DDR3, 1333MHz ECC RAM or higher

(c) Operating System : Genuine Windows 7 Professional 32 bit or

higher and compatible with previous OS versions.

(d) Hard Disk : 600 GB SATA, 7200 rpm HDD

(e) Graphic Card : NVIDIA QUADRO FX 1800 (768MB) or above.

(f) Color Monitor : 21” LCD color monitor with 1 Billion color space and RGB LED back light with programmable color or higher.

(g) Network Port : Integrated dual 1 GBPS network port or

higher. (h) Storage Device : DVD ROM, DVD +/- RW, Blue ray disk, USB

media card reader or higher.

(j) Std I/O port : USB 2.0 (four on front panel) or higher. (k) Security : Setup / BIOS password I/O interface security. (l) Key board : 104 Keys as P/S2/USB or higher. (m) Mouse : Three button scroll optical mouse or higher.

2. TECH SPECIFICATIONS OF SOFTWARE – 25 Nos.

(a) DIGITISATION & UPDATION.

• Auto seed file generation for a given sheet No, Lat -Long.

• Auto warping/geo referencing

• Auto feature extraction from scanned map, imagery in various file formats

2

• Auto layer merging facility

• Auto contour generation and ability to identify contour xg various features and

take corrective measures

• Ability to convert from FPS system to Metric sys

• Ability to read text from the scanned, referenced docu, files etc and

incorporate in digital data

• Easy conversion between datum Everest/WGS-84 and projections Polyconic/

LCC and many more

• Auto edge adjustment with adjacent maps

• Dynamic display of Lat – Long

• Dynamic display of Eastings & Northings

• Auto generation of DVD - I

• Auto history sheet prep

• Auto grid generation for the given sheet No for both Everest and WGS-84

datum and many more

• Auto map frame generation for the given sheet No for both Everest and

WGS-84 datum and many more

• Ability to iden map series numbers of Everest and WGS-84 datum and easy

conversion of map sheets of various scales

• Interoperability among various soft wares available in the markets

• Tools to permit selection of portion of digital data either by using mouse or by

specifying lat-long or easting & northing

• Auto sweep facility between Poly-Everest and LCC-WGS84 w/o loss of data

• Manage dimension, text, line, detail symbols, and display styles with DGN

Libraries as per Data Model Structure (DMS)

• Drawing composn content and workflow control

• Element Templates integrate CAD standards with Tasks

• Geospatial Referencing using multiple coord systems

• OGC Web Map Server sp

• Geospatial PDF creation and ref

3

• Ability to sp various image file formats

• Ability to sp multi-page PDFs

• Multiple wavelet compression formats

• Dynamically-update all annotation

• Create Link Sets to manage relationships between DGN, DWG, PDF and

Microsoft Office docu

• Customizable interface to group tools and tasks

• AccuDraw for dynamic input with heads-up display

• Keyboard Posn Mapping

• Batch convert multiple formats

• Aggregate and assy multiple file formats including: DWG, DXF,PDF, U3D,

3DS, Rhino 3DM, IGES, Parasolid, ACIS SAT, CGM, STEPAP203/AP214,

STL, OBJ, VRMLWorld, Google Earth KML, SketchUpSKP, Collada, ESRI

SHP Files

• Ref 2D/3D DGN , DWG and many other vector files

• Att large image files as ref files

• Att PDF files as a ref

• Curve, surface, mesh, feature, and solids modeling in a single solution

• Intuitively push, pull, drag, cut, & extrude 3D geometry

• Create 3D print-ready models with easy to use tools

• Model geometry, capture relationships, and create forms parametrically using

generative Components

• Use models from Google 3D Warehouse and many other sources

• Multi-core sp for 32 bit processors

• Rich Photorealistic Content (RPC) available online

• Luxology powered for speed and realism

• Key frame & time-based animation

• Timeline and velocity graph

• Create, manage, and navigate plot sets with print organizer

4

• Control print settings using print styles

• Batch print multiple drawings

• Publish intelligent 2D/3D PDFs using genuine Adobe™ PDF tools

• Plug and play facility with all plotters w/o any addl software

• Coord 3D models & 2D drawings automatically

• Drag and drop plans, elevations and sections to create documentation

• Slice & filter 3D models to improve interactive visualization

• Automated drawing updates when models change

• Update all linked annotation dynamically

• Navigate from content in one file or model to others using hyperlinks

• Publish intelligent PDFs that retain all hyperlink intelligence

• Design History enables revision control by recording all changes

• Roll back design file changes from any wk session

• Compare and plot design file changes

• Digital Signatures with 2048-bit public/private keys

• Control digital rights to view, edit, print and copy file content

• Publish i-models for design review workflows

• ProjectWise® integration for ref file and workspace management, and title

block integration

• Integrated design file versioning

• Microsoft SharePoint integration

• Customizable user interface

• User defined Macros

• Sp for Microsoft (VBA) .NET, C++ and Bentley MDL

• Universal database connection

• Element Transparency, display priority, and gradient fills

• Microsoft Windows, Vista, and XP logo compliance

• Pooled licensing via SELECTserver

5

• Import digital data from svy instruments and auto map generation

• Import digital data from GPS and incorporate in data base

• Auto mosaicing of satl imageries/ae photographs

• Auto georeferening/warping

• Auto feature extraction and preparing of insertion and deletion guides

• Ability to check updation of map sheets as per the GIS policy

• Ability to generate contours from SRTM/ASTER

• Auto download facility of SRTM/ASTER from website for the given lat-

long,sheet No,easting & northing

• Auto download facility of ETM imageries from website for a given lat-

long,sheet No,easting & northing

• Auto updation of digital data with insertion and deletion guides

• Incorporate inputs coming from various sources while updating

• Able to import details mentioned in MS word/note pad directly into digital data

by reading lat-long,eastings-northings and update the digital data.

• Able to prep a history sheets containing details of updation including insertions

and deletions and their lat-long, eastings-northings, details of features as per

DMS(Data Model Structure) and pers involved in the process

• Auto tagging of contour heights

• Ability to sp all images and their resolutions and formats

• Provide facility to the administrator to intervene the process at any stg and

carryout amendments and proceeds further

(b) PUBLICATION & PRINTING.

• Auto cell library replacement

• Auto patterning

• Auto incorporation of mag declination, Z numbers, updation details for given

sheet No, lat-long, easting &northing

• Auto map frame generation for the both Polyconic -EVEREST and LCC- WGS-

84

• Ability to sweep in between the Polyconic -EVEREST and LCC- WGS-84

6

• Ability to pattern the map sheet in both Polyconic -EVEREST and LCC- WGS-

84 at a time

• Provide facility to the administrator to intervene the process at any stg and

carryout amendments and proceeds further

• Auto colour generation, seperation and CYMK creation

• Auto generation of grid text as per the DMS(Data Model Structure) for the given

sheet

• In built IPLOT capabilities.

(c) DTED.

• Able to generate from svy data, ASCII files, 2D/3D graphics and digital

elevation maps

• Creation of triangles, lattices, bldg pads

• Dynamic vis editing tools

• Extensive analysis tools incl slope and elevations, intervisibility and a surface

navig camera

• Coord geometry module supports comd line and graphical tools

• Graphical and element based horizontal alignment genr

• Extensive feature database sp for feature mapping

• Network least squares, transit rule and compass rule adjustment routines

• Processing of virtually all data sources raw, ASCII, Total Stn/offset/elevation,

ASCIIXYZ etc

• Create three-dimensional views directly using GIS data.

• Analyze three-dimensional data using cut/fill, line-of-sight, and trn modeling.

• Navigate through multi resolution trn data seamlessly.

• Do spatial analysis in two or three dimensions.

• Export visualizations into videos.

• Visualization tools incl Visualize extremely large data sets (terabytes),Drape

two-dimensional data on a surface or globe ,Extrude data into walls and lines in

3D objects

7

• Dynamically view data from internet map services ,view a scene from multiple

viewpoints using different viewers ,use shading, ill, and transparency properties

to visualize data for different effects, change the vertical exaggeration of the trn

for better clarity

• Apply std symbology for consistent displays as per DMS

• Surface analysis tools incl hill shade ,slope ,aspect ,curvature ,cut/fill , View

shed ,L of S ,surface length surface spot ,surface vol ,Interpolate shape , reclass

,slice ,create contours, 360o view, stop in between and do analysis,

• Auto sweep between various datum Everest, WGS-84, Geo etc.

• Able to provide prebuilt/customized (user friendly), three-dimensional styles for a

variety of real-world, photo-realistic symbols. These styles incl 3D houses ,3D

skyscrapers ,3D industrial buildings and eqpt ,3D basic shapes , 3D street

furniture (signs, lights, benches), 3D trees and plants ,3D vehicles, Mil Symbols,

etc.

• Import/export of various video formats and interoperability

(d) GIS and Image Processing.

• Should be able to store spatial Data in industry standard RDBMS Format

• Create hot link/hyperlink to external application, macro, or URL

• Create/manage/use spatial bookmarks

• Use map templates to standardize maps

• Interactively set transparency for all data • Interactive histogram for data classification

• Create layers or shortcuts to geographic data that store symbology for displaying features.

• Thematic classifications like: Single symbol, Unique value, Match to predefined style, Graduated colors or symbols, Proportional symbols, Dot density mapping, Chart mapping including pie and bar chart, Bivariate and multivariate data rendering.

• Should support rule based symbology and cartographic representations of map entities.

• Should support 2 D animations with time series data support and historical play back of event data.

• Image classification like thematic classes, Individual band settings, Color maps, Contrast, Brightness.

• Should have Image rectification tools for easily georeferencing existing scanned images.

• TIN data classification like Classify and render faces, Nodes, Triangles, Slope, Aspect, Elevation, Hillshade.

• Interactive symbol composer

• Advanced drawing options for control over draw order

8

• On-the-fly automatic labeling, multi-labeling, interactive labeling, rotation of labels from an attribute field, interactive label placement, predefined label styles & finally save labels as a data layer

• Export graphics to: Enhanced Metafile (EMF), Windows bit map (BMP), Encapsulated PostScript (EPS), Tagged image file format (TIFF), Layered Portable document format (PDF), Joint Photographic Experts Group (JPEG), Computer graphics metafile (CGM), Adobe Illustrator (AI), etc.

• Create layers from all supported data sources including coverage feature classes; shapefiles; CAD, TIN, raster, and geodatabase feature classes; or tables containing x,y coordinates.

• Create group layers from multiple data sources including vector overlays on top of raster data.

• Spatial references including the ability to customize and save the custom settings.

• Custom file type support to view specific files

• Documentation/Metadata management.

• On-the-fly Projections and transformations of the Layers

• Set display projection of map using predefined or custom parameters (includes specifying geographic coordinate system or datum).

• The software should have inbuilt Reports Generation facility without requiring any additional software.

• Facility to display Aerial, Projection and Surface distances.

• Edit multiple layers simultaneously with Unlimited undo/redo operations

• Should be able to control & create rule based topology for the spatial database residing in RDBMS.

• Feature construction tools including: Point-and-click feature location with mouse, Streaming locations with mouse, x, y coordinate input with keyboard coordinate input with keyboard.

• Feature edits tools including: Move, rotate, delete, copy, and paste, Reshape, Split and trim, Divide into N-parts or into specified intervals, Vertex editing (add, delete, move), etc.

• Spatial adjustment tools including: Rubber sheeting, Transformation, Edge matching, Attribute transfer.

• Snap to vertex, endpoint, midpoint, or along the edge of features & layer wise snapping

• On-the-fly dynamic joins between different databases • Create statistics & various statistical operations, viz. create charts and reports,

and Sort tables by multiple attributes, Populate values based on expression, Summarize data.

• Connect to and use remote database data (Oracle, SQL, Access, etc.)

• Should be able to plot data on the map directly from the tables.

• Customizable look and feel (drag and drop to rearrange tools/toolbars)

• Create and save macros using Inbuilt Visual Basic for Applications (VBA)

• Use any COM-compliant language for development environment

• UNICODE support for Multilanguage attributes

• Automatically generate metadata

• Import/Export metadata

• Find tool to find data based on metadata and location, web enabling the metadata.

9

• Direct Read of Vector Data like Shapefiles, Coverages, Geodatabase, VPF, etc.

• Direct Read of CAD DXF, DWG, DGN

• Direct Read of Raster (all industry standard Raster formats)

• Should have the facility to interactively change brightness, contrast, and transparency, set resampling method - Nearest neighbor, bilinear interpretation, and Cubic convolution of the raster database.

• Georeferencing of Raster, Vector data. Raster-raster, Raster-Vector, Vector-Raster, Vector-Vector and vice versa should be possible.

• Should be able to operate on Windows 2000 / 2003, Windows XP

• Should have to flexibility to utilise Unix License on Windows 2000/2003/XP.

• Should have the functionality of creating GUI based workflows and models

• Should have the capability to web enable the GUI based workflows and models without any customisation

• Should have inbuilt Geo-spatial data management software alongwith inherent RDBMS so that multiple users can access the same object oriented Geo-spatial data

• Should support publishing and encryption of GIS maps for the purpose of Viewing and Querying GIS data by multiple royalty free GIS data readers

• Build surface models from any data

• Perform interactive perspective viewing, including pan and zoom, rotate, tilt,

• and fly-through simulations with speed controls, for presentation, analysis, or

• export for display on the Web

• Model real-world surface features such as buildings

• Generate three-dimensional surfaces on-the-fly from attributes

• View a surface from multiple viewpoints, query a surface, determine what is

• Visible from a chosen location on a surface, and create a realistic perspective • Image draping raster and vector data over a surface.

• Should have the capability to web enable the 3D models without any customisation

• Apply data normalization and exaggeration on-the-fly

• Drape two-dimensional data on surfaces and view in three dimensions

• Drape Image/Raster data on surfaces and view in three dimensions

• Calculate surface area and volume, slope, aspect, and hillshade

• Generate contours as two-dimensional or three-dimensional shapes

• Perform view-shed and line-of-sight analysis, spot height interpolation,

• Profiling, and steepest-path determination

• Query three-dimensional data based on attribute or location 3. Workstation for Photogrammetric System – 15 Nos. System Specifications The workstation should have the following spec:-

(a) Dual processor Intel Xeon Quad core 3.2 GHz or more frequency 8 MB L3 cache or higher

10 (b) 12 GB DDR3 1333 MHz ECC RAM or higher (c) NVIDIA QUADRO Fx 4800 (1.5 GB) Graphic controller or higher. (d) Dual 21” LCD color monitor or higher (e) 3 x 450 GB SAS 15K rpm HDD or higher. (f) Integrated dual 1 GBPS network port. (g) 104 Keys as P/S2/USB Key board + 3 button optical mouse. (h) DVD writer.

(i) 16 button topo mouse for 3D digitization high precision 34” x 122” digitizing surface in a single table.

(j) Crystal eyes stereo kit including Glasses, Emitter & Cable. 4. Software – 15 Nos. The photogrammetry software should have the following capabilities.

(a) Project setup

• Set up and data management of photogrammetric projects.

• Entry/edit menus

• Bulk input/output of photogrammetric data

• Standard set of data reports and the archive/restore of projects

• Central photogrammetric data manager and central data store

• Powerful environment for both monoscopic and stereoscopic orientation and triangulation of digital photogrammetric images.

• Perform standard Interior and Relative measurements as well as Absolute Orientation for use in both bundle adjustment or independent Model Adjustment

• Built-in-on line bundle adjustment program for job of photos/images.

• Automatic film winder.

• Mosaicing software and Antivirus S/W

(b) Digital Menstruation/ Orientation

• Ability to do standard single photo resection

• Easy to use Windows Interface

• Direct access to Project functions via pull down menus

• Simplified mouse control during stereo measurement plus real-time planning for image movement

11

(c) Stereo viewing

• Modules to display and manipulate stereo imagery with photogrammetrically accurate 3-D cursor tracking, stereo vector superimposition, and image contrast and brightness adjustments.

• Accept both stereo resampled and raw images.

• On-the-fly epi-polar re sampling

• Automatic contrast and brightness adjustment

• Easy to use, map feature digitizing system for use with stereo imagery.

• Efficient map feature digitizing system

• Commands to collect and edit feature data

• Screen-based menus to provide a user interface designed for map production.

• Feature based table allowing the user to define a series of map symbols and manage them on a job by job basis.

• Jump to xyz

• Multiple stereo windows

(d) Stereo feature collection

• Setting the feature’s graphic characteristics and digitizing model commands in the feature table.

P-13 • When a feature is selected while digitizing, all models and

commands for that feature must be activated.

(e) Interactive DTM collection and Automatic DEM Generation

• Provide an interactive method for collection digital terrain model (DTM) data, elevation points and break lines, in stereo models.

• Feature table to allow users to define their geomorphic feature and thus manage multiple mapping jobs with similar or unique symbolizing

• Collect regular grids , break lines , mass points and other geomorphic features

• Edit the data collected within or DTM data coming from other geomorphic features

• While editing, the surface may be represented as points, a TIN surface, or contours

• Ability to edit the DTM points and have either the TIN surface or contours update in 3-D in real time.

• Automatic extraction of DTM elevation points from digital aerial/ satellite stereo images.

12

(f) Ortho rectification

• Interactive and a batch oriented program for orthorectification of aerial photograph /Images which can serve the needs of both small and large scale GIS and map production organization

• On-screen icon menus and a simple user interface for immediate productivity

• Ability to auto rectify images which reside in an Photogrammetric project

• Flexible re sampling and interpolation options

• Use of DTM files in grids or TIN formats or ASCII format

• Ability to place control points in a design file over ortho photos to check the accuracy of rectified images

• Ability to create , delete and extract over views

• JPEG(Image- compression) Support

• Auto mosaicing of images / photos SCANNERS AND PLOTTERS 5. Colour Scanners – 02 Nos.

• The scanner should be able to scan document size of 40 // (101.6cm) x roll length(Minimum)

• The scanner should be able to scan document thickness upto 0.1 // (2.5 mm) paper, mylar, for boards, gator boards non-abrassive paper, vellum, sepia, blueprints, plastic film, plas laminate, foam board ect.

• The scanner should be able to handle data formats: Line art (Black & White) / 256 Gray scan RGB. P-14

• The scanner should be able to do color correction and 2-D filters for color sharpening, softening and blur reduction.

• The scanner should have scan speeds up to 76 mm (3) per second(color) and 254 mm(10) per second(black and white)

• The scanner should have resolution up to 9600 dpi, with variable resolution setting from 50 dpi.

• The scanner should have standard memory of 4 GB

• The scanner should have scan speed of 25 sec/page on AID 6. Colour Plotters – 02 Nos.

• The plotter should be able to plot documents –media of A4, A3, A2, AO size sheets and rolls.

• The plotter should minimum use thermal inkjet with 6 cartridges CYMK, light Cyan and light magenta technology.

• The plotter should be capable to hold roll sizes- 300ft (91mtr) length x 60 inch rolls.

• The plotter should be capable to use paper (coated or glossy), banners, opaque vinyl, canvas postal paper, color lucent black lit UV cloth.

13

• The plotter should be able to automatically cut and have a bin for at least 20 drawings.

• The plotter should have resolution Up to 2400 x1200 optimized dpi.

• The plotter should be able to plot HPRTL, HPGL/2, and Adobe port script 3.

• The plotter should have touch screen fast preview and ensure greater control over final output.

• The plotter should have DVD/CD reader.

Servers

7. Data Base Servers – 06 Nos.

Processo : 2 X Quad-Core Intel ® Xeon ® E 7310 Processor (1.60 GHz,

2x2M cache. 80 Watts) scalable to 4 CPUs. Chipset : Industry Standard Intel ® 7300 Chipset FSB : 1066 MHz Cache : Up to 8 MB of L2 Cache Memory Type : PC2-5300 Fully Buffered DIMMs (DDR2- 667) @ 667 MHz Memory : 12 GB & Upgradeable to 256 GB of Memory Memory Slots : Min 16 Memory slots upgradeable to 32 slots Memory Features

: 4-way interleaving, Advanced ECC, Mirrored Memory, Online Spare Memory

Network Controller

: Two embedded Multifunction Gigabit Network Adapters with TCP/IP Offload Engine , including support for Accelerated iSCSI

Expansion Slots

: Min. 8(Eight) slots standard: (4) full length PCI-E x8, (1) full length PCI-Ex4 and (3) half length PCI-Ex4 slots; Upgradable to up to 11 slots

Storage Controllers

: SAS Controller with min. 256 MB Battery Backed WRITE Cache,

upgradable to 512 MB Storage Bays : Min 8 SFF 2.5” Hot Plug drive bays, upgradeable to 16 HDD bays

Hard Disk Drive

: SFF 2.5” 10K SAS drives

Optical Drive : Slim line DVD Interfaces : 1S, 1KBD, 1 Video, 1 Mouse, 5 USB(min1 interval) Graphics : Integrated ATI-RN50 with 32 MB DDR memory Form Factor : 4 U Rack Mountable Manageability : Dedicated Hardware Controller based Management Manageability Features

: Should be able to manage systems through a web-browser

OEM to provide its own systems management software Alphanumeric or numeric pager alerts Pre- failure WARRANTY for CPU, Memory & Hard Disk. Part to be replaced based on impending failure alert to be provided by the systems management software BEFORE actual failure of component

It should provides Secure Sockets Layer (SSL) 128 bit encryption

and Secure Shell (SSH) Version 2 and support VPN for secure access over internet

Redundant ROM Should be able to generate a report on Inventory & automatically track server warranty information Automatic check & update of hardware drivers & Bios Version Control

8. Application servers

Chassis : 2 U Rack Mountable

CPU : One - Two * Quad/ Dual Core Intel Xeon Processor, 8 MB (1x8 MB) L3

Cache (MAX) – 4 MB (1*4 MB) L3 cache (MIN)

Motherboard : Intel R 5520 Chipset

Memory :144GB with PC3-8500R DDR3 Registered (RDIMM) memory, operating a 800 MHz 24 GB with PC3-10600E DDR3 Un buffered (UDIMM) memory, operating at 1066MHz

Memory : Protection : Advanced ECC (multi bit error protection), Mirroring mode,

Lockstep mode

Bays : Minimum 8 (scalable up to 16) Hot Plug 2.5” hard disk bays/ 6 Hot Plug 3.5” hard Disk bays + CDROM/DVD Bay

Hard Disk Drive

: Up to 8 (16 with optional second SAS drive cage*): Hot plug SFF SAS

10 K 300/146/72/36 GB, Hot plug SFF SAS 15K 146/72/36 GB Hot plug SFF SATA 5.4K 250/120GB

Controller : SAS Raid Controller with RAID 0/1/1+0/5/5+0 with 256/512 MB battery backed write cache (onboard or in a PCI Express slot)

Networking Features

: Dual Port Multiplication Gigabit Server Adapters with TCP/IP Offload Engine, including support for Accelerated iSCSI

Ports : USB 2.0 support with 5 total ports: 2 up front; 2 in back; 1 interval secure digital (SD) slot

Bus Slots : Six PCI- Express slots, optional mixed PCI-X/ PCI- Express or * 16 PCI configurations

Optical drive : DVD/CD-RW combo drive

Power Supply : Redundant Power Supplies and fans

IS Compliance : ACPI 2.0 Complaint, PCI 2.2 Complaint, WOL Support, Microsoft R

Logo certification

14

15

Security : Hardware-based system security feature that can securely store information, such as passwords and encryption keys, which can be used to authenticate the platform

OS Support : Microsoft Windows Server, Microsoft Windows Server Hyper- V, Red Hat Enterprise Linux (RHEL), Red Hat Enterprise Linux Virtualization, SUSE Linux Enterprise Server with XEN Oracle Enterprise Linux (OEL), Solaris 10 for x86/x64 based systems, NetWare, VMware, Citrix Essentials for Xen Server

Remote Manageability Software

: System remote management software should support browser based Graphical Remote Console; Virtual Power button, Remote boot using USB/CD/DVD Drive and should be capable to offer upgrade of software and patches from a remote client using Media/ image/folder; server power capping and historical reporting; should have support for multifactor authentication. Remote console sharing during pre- OS and OS runtime operation, console replay- console replay captures and stores for replay the console video during a server’s last major fault or boot sequence. Microsoft Terminal Services Integration, 128 bit SSL encryption and Secure Shell Version 2 support. Should provide support for AES and 3DES on browser. Should provide remote firmware update functionality. Should provide support for Java free graphical remote console.

Server Management

: The System Management software should provide Role-based security. Should help provide proactive notification of actual or impending component failure alerts on critical components like CPU, Memory and HDD. Should support automatic event handling that allows configuring policies to notify failures via- e-mail, pager, or SMS gateway or automatic execution of scripts. Should support scheduled execution of OS commands, batch files, scripts, and command line apps on remote nodes. Should be able to perform comprehensive system data collection and enable users to quickly produce detailed inventory reports for managed devices. Should support the reports to be saved in HTML, CSV or XML format. Should help to proactively identify out-of-date BIOS, drivers, and Server Management agents and enable the remote update of system software/firmware components. The server Management Software should be of the same brand as of the serve supplier.

16

9. Main storage server

Operating System and Clustering Support

: The storage array should support industry-leading Operating System platforms including: Windows Server 2003, Windows Server 2008, VMware, HP-UX, Solaris and Linux.

Capacity & Scalability : The Storage Array shall be offered with 10 TB Capacity using 300 GB SAS drives & shall be scalable ti minimum of 60 number of drives or 17 TB using 300GB SAS drives.

Architecture : The storage array should support dual, redundant, hot-pluggable, active-active array controllers for high performance and reliability

No single point of Failure

: Storage Array shall be configurable in a No Single Point of configuration including Array Controller card, Cache memory, FAN, Power supply etc.

Disk Drive Support : Storage Array shall support minimum 146/300/450GB hot-pluggable Enterprise SAS hard drives along with S-ATA (1000 GB) drives.

Cache : Storage Array shall be given with minimum of 1GB cache per controller in a single unit. Cache shall be backed up in case of power failure for indefinite time either using batteries or capacitors or any other equivalent technology.

Raid Support : Storage Subsystem shall support Raid 0, 1, 1+0, 3, 5, 5+0 and Raid 6 with Dual Parity Protection.

Point in time and clone copy

: 1. Storage array shall have array based support of (with the help of optional license) Both Snapshot and clone functionality.

2. Storage array shall support at least 255 point in time copies (Snapshots) and 128 clone copies.

Ports

: Storage sub system shall be offered with quad 3GBps SAS ports per controller.

Global Hot Spare and Dedicated spare

: 1. Storage Array shall support Global hot Spare for offered Disk Drives.

2. At least 2 Global hot spare drives shall be configured for every 30

drives.

3. Storage subsystem shall also support dedicated spare for critical raid sets.

Logical Volume : Storage Subsystem shall support minimum of 500 Logical Units. Storage Array shall also support creation of more than 12 TB volumes at controller level.

Load Balancing & Multipath

: Multi-path and load balancing software shall be provided, if vendor does not support MPIO functionality of Operating System

Performance Management

: Storage system controller shall have inbuilt performance management software.

17 10. Large Format Film & Plate Based Laser Plotter System – 02 Nos.

• The plotter should support line art plotting and screened composites at 3500 dpi or higher for maximum quality & shall allow films to be generated at optimal resolution for data type and halftone requirements.

• The plotter should include Halftone screens with the system.

• The plotter should have Round or elliptical dot, bi-angle, line, cartographic mezzotint, AM & FM stochastic, geometric dither pattern Screens.

• The plotter should have separate calibration profiles separately for each screen to accommodate dot gain.

• The plotter should allow raster data input at lower resolution to be screened

and exposed at high resolution. • The plotter should have optimized performance and plot quality while

minimizing file sizes.

• The plotter should produce screens and patterns at high resolution to meet critical cartographic standards

• The plotter should allow scanned output to be matched to the end application

• The plotter should support for binary, Grayscale and color data during scanning

• The plotter should provide fast capture of all media types used in map production

• The plotter should provide on the fly color classification and run length data compression to scan large color maps & on-the-fly JPEG compression for disk compression of true color scans

• The plotter should use the symbols, line styles, patterns etc directly from the library already generated

• The plotter should allow size -120x162.5 cm, media size 122x170 cm.

• The plotter should plot latest Industrial file formats.

• The plotter should supports industry standard Post script format by off line RIP to grayscale or screened binary raster at user specified resolution.

• The plotter should have minimum 8 beam laser to optimize plotting speed,

plotting resolution of minimum 3500 dpi & the plotting speed (full drum) of higher than 7 mega pixels/sec (less than 30 min for full drum at 3500 dpi)

18

• The plotter should have Binary Line art of halftone (screened continuous-tone) plotting modes.

• The plotter should support standard lithographic films, CTP aluminum printing plates

• The plotter should allow media thickness of 0.1 to 3 mm (0.004 to 0.250 in) the plotter should have reliability of +/-6 microns

11. Film processor

The film processor should be capable to process output films exposed on the laser writer for further plate making and printing workflow & should include the following features:-

• Material width up to 135 cm

• Dry-to-dry developing

• Computerized temperature, speed and processing time control

• Computerized chemistry monitor

12. Plate processor The plate processes shall be able to process output from the laser writer for further printing workflow and shall include the following features:-

• Plate re-entry facility

• Day light or darkroom operation

• Auto wash water filtration system

• Capable to undertake plate width of 150 cm. MISCELLANEOUS REQUIREMENTS

13. The system should be simple to operate and easy to maintain. 14. The following publication / literature should be made available by the OEM / auth dealer:- (a) Exhaustive user handbook in softcopy as well as hardcopy. (b) Technical manual. (c) Complete equipment schedule. (d) Original system software CD’s. (e) Operating instructions. (f) Equipment maintenance schedule and checks.

15. The equipment should be procured from OEM/ stockiest / distributor with wide service support network in order to provide onsite maintenance as and when required.

Appendix ‘B’ 1, Name of the Vendor/Company/Firm.

____________________________________________________________________ (Company profile, in brief, to be attached) 2. Type (Tick the relevant category). (a) Original Equipment Manufacturer (OEM) - Yes/No (b) Government sponsored Export Agency - Yes/No (Detail of registration to provided) (c) Authorised Representatives ofOEM - Yes/No (Attach details) (d) Other (Give specific details) --------------------------------------------------------------------------------------------------------- _______________________________________________________________ (e) Any collaborator/partner in India ( in case of foreign vendors). 3. Contact Details. Postal Address ________________________________________________________

____________________________________________________________________ City _____________________________ Province ___________________________ Country________________________ Pin/Zip Code ___________________________ Tele: __________________________ Fax _________________________________ URL/Web Site: ________________________________________________________

2

4. Local Branch/Liaison Office/Authorised Representatives, in Delhi, if any). Name & Address: ______________________________________________________ ____________________________________________________________________ City ____________________________ Province: ____________________________ Pin Code ______________ Tele: ___________________ FAX __________________ 5. Financial Details. (a) Annual turn over : _______________________________ USD (b) Earlier contracts with India Ministry of Defence/Government agencies: - Agency Contract

Number Equipment Quantity Cost

(c) Details of manufacturing infrastructure available: __________________ 6. Certification by quality Assurance Organisation (If applicable).

Name of Agency Certificate Applicable from

(Date & Year) Valid till (Date & Year)

7. Equipment/Product Profile (to be submitted for each product separately). (a) Name of Product: ___________________________________________ (Should be given category wise for e.g. all products under night vision devices to be mentioned together) (b) Description (attach technical literature): __________________________ _______________________________________________________________

3

(c) Whether OEM or Integrator: ___________________________________ (d) Status (in Service/Design development state): ____________________ _________________________________________________________ (e) Production capacity per annum: ________________________________ (f) Counties where equipment is in service: _________________________ (g) Whether export clearance is requied from respective government (Foreign vendors only): ____________________________________________ _______________________________________________________________ (h) In case of equipment and ammunition JB MOU compliance to be specified. (j) Details of any collaboration/joint venture/co-production/authorized dealer with Indian Industry (Foreign Vendors only): ____________________________ _______________________________________________________________ Tele: __________________________ FAX: ___________________________ 8. (a) Are you making the full eqpt or it is being integrated by you? Give details (b) What are the components, sub-system or sub-assemblies of the eqpt which are not manufactured by you? Please give details. 9. Any Other Relevant Information. ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________