RENESSE

Thank you for your recent purchaseof the TOTO® product. Please read theenclosed information to ensure the safe use of your product. .

Installation and Owner’s Manual

2007.5

•

™

0GU3026

TL170DD

Important Safeguards---------------1Specifications -------------------------2Before Installation--------------------2Components ---------------------------3Set-Up Drawing -----------------------4Installation Procedure --------5~10Maintenance --------------------12~13Troubleshooting --------------------13Replacement Parts------------------14Warranty -------------------------------15

Widespread Lavatory Faucet

Contents

®

English Español Français

DISCO

NTI

NUED

Important Safeguards(For your safety, please follow the instructions below)

Warning Do not reverse the hot and cold water inlets. You may be scalded if they are reversed.

Do Not Do not use hot water supply that is higher than185°F (85°C). Do not use steam as hot water supply.

If water is hotter than 185°F is used. If it is broken, property damage, scalding, and other injuries may occur.

Do not disassemble

Do not disassemble or modify the item in anyway not described in this manual.

If the system is broken, property damage, scalding and otherinjuries are likely to occur.

Read the “Important Safeguards” section thoroughly before installing the product.

Warning

Caution

●The following symbols indicate safe and proper use of the product. Failure to observe them may reult in injury or property damage.

Failure to observe this symol may result in serious injury.

Failure to observe this symbol may result in injury or property damage.

Absolutely Do NOT.

Do not disassemble

Mandatory!

The following table demonstrates the use of safety symbols in this manual.

Less than185°F(85° C)

HC

Hot water Cold water

Do Not

Caution

Do notTouch

Spout and seat may cause scalding when they are hot.

While using hot water, do not touch the spoutand escutcheon directly.

Spout

escutcheon

HOT

Do not strike or kick the product.

If the system is broken, property damage, scalding, and other injuries may occur.

Do not use the product at temperature exceedingwhat local codes allow.If parts are damaged, property damage, scalding and otherinjuries may occur.

Freezing

1

English

DISCO

NTI

NUED

Specifications

34˚F?104°F (2˚C~40˚C)

Cold and hotwater pressure

Minimum pressure

Maximum pressure

Supplied Water Temperature

Suitable Water Quality

Suitable ambient temperature

Supply Connection

20 psi (0.14MPa) (flowing pressure)

125 psi (0.86MPa) (static)

Less than 185°F (85°C)Water that meets National/Primarydrinking water regulation

3/8” NPSM

●To prevent being scalded due to malfunction, the cold water supply pressure must be higher than the hot water pressure, or you can make them equal. In addition, if you increase the pressure of the hot water, it still must be lower than that of cold water supply side.

●For ease of water flow adjustment and inspection with tools, you should prepare an extra stop valve.

●You may find residual water in the product ; this is due to water test for quality assurance before packaging.

● If the water supply pressure is higher than 125psi (0.86MPa), you should buy a reducing valve to reduce the pressure to the range of 0.2-0.3MPa.

To use the faucet comfortably, the recommended pressure is about 30-45 psi (0.2-0.3MPa).

●To reduce resistance, the pipe that is connected to the hot water device should be as short as possible, and the pipe should be wrapped with insulating material.

●To prevent being scalded due to wrong operation, it is recommended the hot water supply temperature is 140°F (60°C).

Before installation

2

Eng

lish

Flow rate Max. 2.2 gpm (8.32 L/min)

DISCO

NTI

NUED

Valve Body Parts

Other

Handle PartsSpout Parts

Spout

Flat packing

Valve bodyassembly(hot side)

Valve bodyassembly(cold side)

Wingedpacking

Shank Assembly

Flat washer (small)

Flat washer (big)

Lock washer (small)

Lock washer (big)

Handleescutcheon (HOT)

C labelH label

Screw Screw

Handle cap Handle cap

Handle Handle

Bush Bush

Hex nut Hex nut

Spacer Spacer

spout mountingflange

Spout mounting nut

shank mountingnut

Some parts may be different depending on the model

Spout key

Give theseto Customer!

Confirm package includes following parts.

Components

Installation andOperation Manual

3

English

- Observe all local plumbing codes.-Make sure that water supply is shut off.-Read these instructions carefully to ensure proper installation.-For new lavatory installation, install the faucet before installing the lavatory

Handleescutcheon (Cold)

gasket gasket

packing (white) packing (white)

packing (black) packing (black)

slip washer slip washer

fastening nut fastening nut

connector

packing

connector

packing

DISCO

NTI

NUED

Set-Up Drawing*Some parts may differ from the illustration depending on the model.

4

Eng

lish

3/8” NPSM

8” (203mm)

CLOSEDCLOSEDCOLDHOT

OPENOPEN

Deck ThicknessMax. 1-3/16” (30 mm)

counter hole Dia.1-5/16”-1-7/16 (φ35±2 mm)

7” (177mm)

3-11/16” (94 mm)

Pop-up Drain cable connector

cable length = 13-13/16” (350 mm)

1-1/4” OD (32 mm OD)

8-9/16” (218 mm)

1-3/4” (44mm)

3” (76 mm)

25-5

/16”

(642

mm

)

DISCO

NTI

NUED

Installation Procedure

1 Clean the cold/hotwater supply pipes

1 Clean the cold/hot water supply pipes Before installation, dirt and debris in the cold/hot water supply pipes must be washed out.

2 Install the Spout

4 Connect the cold/hotwater supply hoses

5 Install the handles

3 Install theValve bodyAssembly

6 Connect the pop-up drain with cable (only for faucet with pop-up drain )

Important

5

English

Close

6Pop-up Drain with Cable installationDISCO

NTI

NUED

6

2 Install the spout

?Insert the packing through the connection pipe and spout fixing shaft to the groove in the bottom of the spout into the hole.

?Insert the spout mounting flange, flat washer, (big), lock washer (big) and spout mounting nut through the spout mounting shaft in the order, face the spout in its front side and attach the parts.

?Install the shank body with the flat washer (small), lock washer (small) and spout mounting nut.

?Wipe off the dirt around the installation hole.

Spoutbottom

Spout mountingshaft

Mountingshaft

Spout Mounting nut

spout mountingnut

Section

Spout

Spout

Spout

Connection pipe

Installation hole

shank body

?Measure the installation hole, select one from the two kinds of packings which meets the hole.

Hole over Hole under Winged packing Flat packing

Caution There are two kinds of packingin the packageSelect the one that meets the hole diameter.

?If the packing is wrong, water may leak under the counter.

Packing

Be careful not to scratch or contaminatethe O ring. Otherwise, water leakage may occur.

Caution

Spout mounting shaft

spout mounting

flangeFlat washer

(big)Lock

washer(big)

Flatwasher(small)

lockwasher(small)

Eng

lish

φ36 mm = 1-7/16in

DISCO

NTI

NUED

3 Install the valve body assembly.?Wipe away the dirt around the installation hole.

?Place the packing (black), slip washer, fastening nut through the water supply and connecting hoses, then fasten the valve body assembly.

●When placing the connecting hose through the fastening nut, make the cap nut go through the escape hole.

?Place the packing (white) through the water supply and connecting hoses, insert them into the hole in the counter.

The valve body assembly (C label) of cold water supply must be installed onthe right side of the spout, the valve body assembly (H label) of hot water supply must be installed on the left side.

Escape hole

Top

Bottom

Valve Body Assembly of cold water supply

Packing (white)

Packing (black)

Slip washer

Counter

Fastening nut

C label

ConnectinghoseCold water

supply hose

Caution

Caution

7

English

Cap Nut

DISCO

NTI

NUED

4

①Find the gasket in the connector and tightenthe connector in the stop valve; use the tool to fasten them.

②Find the gaskets in the cap nuts of thecold/hot water supply hoses, screw onthe connector, use the tool to fasten them.

③Find the gaskets in the cap nuts of theconnecting hoses, screw on the shankbody, use the tool to fasten them.

CautionThe connecting hoses should crosseach other as shown in the right figure.

Cautions for installing water supply hoses●You have to bend the hose, but be careful not to break it.The minimum bending radius of the hose is 2-3/8” (60mm), if you bend it over the limit,it will break, which may cause early damage.●During installation, do not bend the hose from the end surface of the main faucet body too far.●Do not pull the hose violently.This may break the hose.●Avoid unnecessary contact with similar hoses.If the external reinforced layer of the hose is damaged due to friction, the hoseperformance may deteriorate.

Cold/hot watersupply hosebending radius2-3/8” (60 mm)

shank body

Packing

Cap nut

Cold watersupply hose

Stop valve

gasket

connector

gasket

Cap nut

Hot watersupply hose

Connect cold/hot water supply hoses

8

Eng

lish

connecting hose

GOOD BAD BAD BAD

DISCO

NTI

NUED

5

HOT COLD

Install the handles①Place handle escutcheon then spacer on top of the valve unit. Secure with Hex Nut.②Insert the bush and handle into the spindle part of the valve body assembly, use the screw to attach them.

③Insert the handle in the handle.

9

English

Knob Knob

Open OpenClose Close

Spindle part ofvalve bodyasembly

handleescutcheon

Hex Nut

Spacer

Screw

Handle

Bush

Flange

Handle Cap

Up

Caution●Place the spacer with the smallhole facing up.

●Adjust the seats on the cold/hotwater sides to a flat surface, usetool to fasten the hex nut.

●Install the seats so thatthe HOT/ COLD marks are asshown in the right figure.●To install the handle, orient thehandle to make the knob stay inthe position as shown in the right.

DISCO

NTI

NUED

cabletailpiece

u-cup seal

drain body pop up

nut

drain seal

cable handleconnector

cable baseconnector

cable

lock nut

tailpiece

drain body

locknut

drain gasket

flange nut

drain body

flange

lavatory

cable

cable handleconnector

cable baseconnector

press the clip to be able to connect

clip

clip

groove, to which connectionis to be made

6 Pop-up Drain with Cable Installation

- Apply pipe tape to the flange threads.

- Insert flange into the drain hole.

- Assemble the gasket. flange nut and lock nut.

- Apply pipe tape to the end threads of flange threads and install the tail piece to drain body

-Make sure that cable faces toward the faucet.

- Connect the cable base connector with cable handle connector.

Push button

push button

(Only for faucet with Pop-up Drain)

8

Eng

lish

DISCO

NTI

NUED

How to Use

How to adjust the temperature

Open

Open

Cold side

Hot side

Open the main valve of the pipe, confirm water flow out of the spout.

Close

Drain

Drain

Push button

Push

Open

(for Faucet with Pop-up drain )

Drain

Push button

Push

Open and close the Pop-up Drain(only for Faucet with Pop-up drain )

Push the push button. When the pop-up is closed, water can be kept in the washbasin. Push it again, the drain is opened and water will drain out.

Turn the handles: confirm hot and cold water by turning each handle.

To prevent scalding due to malfunction, the recommended hot water supply temperatureis 140°F (60°C)

11

English

DISCO

NTI

NUED

Maintenance

Brush

Unscrew it

Aerator

Aerator

Spout Key 2. Use a brush to clear dirt and debris from the aerator .

?Be careful not to lose the parts that have been removed.

1. Unscrew the aerator by using the spout key provided to remove it.

Use the spout key provided to install it.

3. Install the aerator.

For performance and cleanliness, please maintain the product everyday.

Maintain the water outlet

Using a Cloth to Clean

Slightly dirty

Seriously dirty

Use water and a damp cloth to wipe away thedirt completely.

Use cloth with dilute detergent to wipe away the dirt, then wash and dry it.

Notes:Do not use the following materials

Acidic cleaning agents, alkaline cleaning agents, or bleaches that are not TOTO scale cleaner.

Solvents like thinner and benzene Cleaning agents like cleanser or grinding powder

which contain coarse particlesNylon scrubbers and brushes

12

Eng

lish

DISCO

NTI

NUED

1.For maintenance press the pop button at first

pop up

drain body

pop up

2. Unscrew the pop up counter-clockwise and take it out of the drain body

3. Cleaning utensil such as small brush can be used to clean the pop up

pop up

small brush

Push button

Push

Open

Cleaning Drain

Troubleshooting

Do you lower down the lever handle tostop position? (Is it set to fully closed?)

Is the stop valve fully opened?

Is the aerator blocked with debris?

Is the outlet hole frozen? Apply hot water to the outlet.

Clean the aerator.

Use stop valve to adjust flow.

Lower the lever handle tostop position.

―

―

P.7

P.9

―

Check SolutionProblem Refer to

Water flowswithout stop

Flow is too small When gas water heater device is used

with the product, is the switching method set properly?

Set the gas hot water device properly with professional help.

―

―

Is the aerator blocked? Page 9Clean the aerator.

Temperaturecan not beadjustedeasily.

Is the stop valve on the cold/ Hot sidesfully opened?

Adjust water flow with stop valve

Does the water heater give adequate water?

Check settingson water heaterwith professional help.

Unscrew

Before contacting a repairman, check the following common problems and solutions. Ifthe problem persists, contact your dealer or our tech support.

13

English

DISCO

NTI

NUED

Replacement Parts

No. Description 1 Handle Assembly 2 Handle Escutcheon Set (HOT) 3 Ceramic Cartridge (HOT) 4 Valve Body Assembly (HOT) 5 Connector Assembly 6 Mounting Hardware 7 Drain Assembly 8 Shank Assembly 9 Gasket, nut and O ring set 10 Spout kit 11 Aerator 12 Handle Escutcheon Set (COLD) 13 Valve Body Assembly (COLD) 14 Ceramic Cartridge (COLD) 15 Connector Assembly 16 Mounting Hardware

1

2

3

4

5

6

7

8

9

10

1112

14

13

1516

14

Eng

lish

DISCO

NTI

NUED

WARRANTY

©2007 TOTO USA, Inc. á 1155 Southern Road, Morrow GA 30260Phone (888)-295-8134 Fax (800)-699-4889 www.totousa.comTOTO USA, INC. is a wholly owned subsidiary of TOTO Ltd.

Printed in August, 20070GU3026

LIFETIME LIMITED WARRANTYWarranty applies to selected residential faucets only.1. TOTO® warrants its faucets (“Product”) to be free from defects in materials and workmanship during normal residential use for as long as the original consumer end-user purchaser owns their home. This limited lifetime warranty is extended only to the original consumer end-user purchaser and only so long as the Product remains in use by the original consumer end-user purchaser in its original place of installation in the purchaser’s residence. This warranty applies only to Product purchased and installed in North America.2. TOTO® obligations under this warranty are limited to repair or replacement, at TOTO®’s option, of Product or parts found to be defective in normal residential use, provided that such Product was properly installed and used in accordance with the owner’s manual. TOTO® reserves the right to make such inspections as may be necessary in order to determine the cause of the defect.3. This warranty does not apply to the following items:

Damage or loss sustained in a natural calamity such as fire, earthquake, flood, thunder, electrical storm, etc.Damage or loss resulting from any accident, unreasonable use, misuse, abuse, negligence, or improper care, cleaning or maintenance of the Product.Damage or loss resulting from sediments or foreign matter contained in a water system.Damage or loss resulting from improper installation or from installation of the Product in a harsh and/or hazardous environment, or improper removal, repair or modi cation of the Product.Damage or loss resulting from the use of an abrasive cleanser.

4. If the Product is used commercially, TOTO® warrants the Product to be free from defects in materials and workmanship for one (1) year from the date the Product is installed, with all other terms of this warranty applicable except the duration of the warranty.5. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE.6. To obtain warranty repair service under this warranty, you must take the Product or deliver it prepaid to a TOTO® service facility with proof of purchase (original sales receipt) together with a letter stating the problem, or contact a TOTO ® distributor or products service contractor, or write directly to TOTO® U.S.A., INC., 1155 Southern road, Morrow, Georgia 30260, (888) 295-8134. If, because of the size of the Product or nature of the defect, the Product cannot be returned to TOTO®, receipt by TOTO ® of written notice of the defect together with proof of purchase (original sales receipt) shall constitute delivery. In such case, TOTO®

may choose to repair the Product at the purchaser’s location or pay to transport the Product to a service facility. THIS WRITTEN WARRANTY IS THE ONLY WARRANTY MADE BY TOTO®. REPAIR, REPLACEMENT OR OTHER APPROPRIATE ADJUSTMENT AS PROVIDED UNDER THIS WARRANTY SHALL BE THE EXCLUSIVE REMEDY AVAILABLE TO THE ORIGINAL PURCHASER. TOTO® SHALL NOT BE RESPONSIBLE FOR LOSS OF THE PRODUCT OR FOR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OR EXPENSES INCURRED BY THE ORIGINAL PURCHASER, OR FOR LABOR OR OTHER COSTS DUE TO INSTALLATION OR REMOVAL, OR COSTS OF REPAIRS BY OTHERS, OR FOR ANY OTHER EXPENSE NOT SPECIFICALLY STATED. IN NO EVENT WILL TOTO®’S RESPONSIBILITY EXCEED THE PURCHASE PRICE OF THE PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR USE OR FOR A PARTICULAR PURPOSE, ARE EXPRESSLY LIMITED TO THE DURATION OF THIS WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION AND EXCLUSION MAY NOT APPLY TO YOU.

DISCO

NTI

NUED