NVE-P1

Removable Navigation DriveOwner’s Manual

2

PRECAUTIONS AND NOTICES■ Important Information

This product is intended to provide turn by turninstructions to get you to a desired destination.Please make certain that all persons using thisnavigation system carefully read these precautionsand the following instructions fully.

1) This product is not a substitute for your personaljudgment. Any route suggestions made by thisnavigation system may never supersede any localtraffic regulations or your personal judgmentand/or knowledge of safe driving practices. Donot follow route suggestions if the navigationsystem instructs you to perform an unsafe orillegal maneuver, places you in an unsafesituation, or routes you into an area which youconsider unsafe.

2) Glance at the screen only when necessary andsafe to do so. If prolonged viewing of the screenis necessary, pull over in a safe and legal mannerand location.

3) Do not input destinations, change settings, oraccess any functions requiring a prolonged viewof the monitor and/or remote control while youare driving. Pull over in a safe and legal mannerand location before attempting to access thesystem.

4) Do not use the navigation system to route you toemergency services. Not all locations ofemergency services such as police and firestations, hospitals and clinics are contained in thedatabase. Please use your own judgment and askfor directions in these situations.

5) The map database used in the navigation systemis the most recent map data available at the timeof production. Because of changes in streets andneighborhoods, there may be situations where thenavigation system is not able to route you to yourdesired destination. In these cases, use your ownjudgment.

6) The map database is designed to provide youwith route suggestions and does not take intoaccount the relative safety of a suggested routeor of factors which may affect the time required toreach your destination. The system does notreflect road closures or construction, roadcharacteristics (i.e. type of road surface, slope orgrade, weight or height restrictions, etc.), trafficcongestion, weather conditions, or any otherfactors which may affect the safety or timing ofyour driving experience. Use your own personaljudgment if the navigation system is unable toprovide you with an alternate route.

7) There may be situations where the navigationsystem displays the vehicle's location

erroneously. Use your own driving judgment inthis situation, taking into account current drivingconditions. Please be aware that in this situationthe navigation system should correct the vehicle'sposition automatically. However, there may betimes where you may have to correct the positionyourself. If this is the case, pull over in a safe andlegal manner and location before attemptingoperation.

8) Make certain that the volume level of thenavigation system is set to a level which stillallows you to hear outside traffic and emergencyvehicles.

If there is anything in the manual about the operationof the navigation system which you are uncertainabout, please contact your local Alpine authorizednavigation dealer or Alpine at 1-888-NAV-HELP (1-888-628-4357) before using the navigation system.

FCC Compliance StatementNVE-P1 has been tested and found to comply withthe limits for a Class B digital device, pursuant to part15 of the FCC Rules. These limits are designed toprovide more reasonable protection against harmfulinterference in a residential installation, and are morestringent than "outdoor" requirements.

Operation is subject to the following two conditions:(1) This device may not cause harmful interference,and (2) this device must accept any interferencereceived, including interference that may causeundesired operation.

This equipment generates, uses, and can radiateradio frequency energy and, if not installed and usedin accordance with the instructions, may causeharmful interference to radio communications.However, there is no guarantee that interference willnot occur in a particular installation. If this equipmentdoes cause harmful interference to radio or televisionreception, which can be determined by turning theequipment off and on, you are encouraged to try tocorrect the interference by one of the followingmeasures:

·Reorient or relocate the receiving antenna.·Increase the separation between the equipment andthe receiver.·Connect the equipment into an outlet on a circuitdifferent from that to which the receiver is connected.·Consult an experienced radio/TV technician.

Please Read Carefully Before Using This Product.

3

WARNINGS

Read this manual carefully before using this system.It contains instructions on how to use this product ina safe and effective manner. Alpine cannot beresponsible for problems resulting from failure toobserve the instructions in this manual.

This manual uses various pictorial displays to showyou how to use this product safely and to alert you topotential dangers resulting from improperconnections and operation. Following areexplanations of these pictorial displays. It isimportant to fully understand the meanings of thesepictorial displays in order to use this manual and thesystem properly.

DO NOT OPERATE ANY FUNCTION THAT TAKES YOURATTENTION AWAY FROM SAFELY DRIVING YOUR VEHICLE.Any function that requires your prolonged attentionshould only be performed after coming to a completestop. Always stop the vehicle in a safe locationbefore performing these functions. Failure to do somay result in an accident.

KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILLHEAR OUTSIDE NOISE WHILE DRIVING.Failure to do so may result in an accident.

MINIMIZE DISPLAY VIEWING WHILE DRIVING.Viewing the display may distract the driver fromlooking ahead of the vehicle and cause an accident.

DO NOT DISASSEMBLE OR ALTER.Doing so may result in an accident, fire or electricshock.

USE THIS PRODUCT AS SPECIFIED.Use for other than its designed application may resultin fire, electric shock or other injury.

DO NOT PLACE HANDS, FINGERS OR FOREIGN OBJECTSIN INSERTION SLOTS OR GAPS.Doing so may result in personal injury or damage tothe product.

HALT USE IMMEDIATELY IF A PROBLEM APPEARS.Failure to do so may cause personal injury or damageto the product. Return it to your authorized ALPINEdealer or the nearest ALPINE Service Center forrepairing.

PRECAUTIONSTemperatureBe sure the temperature inside the vehicle is between+45°C (+113°F) and -0°C (+32°F) before turning yourunit on.

Servicing the UnitIf you have problems, do not attempt to repair theunit yourself. Return it to your ALPINE dealer or thenearest ALPINE Service Station for servicing.

Installation LocationMake sure the NVE-P1 will not be exposed to:• Direct sun and heat • Excessive dust• High humidity • Excessive vibrations

This symbol means important instructions.Failure to heed them can result in seriousinjury or death.

WARNING

This symbol means important instructions.Failure to heed them can result in injury ormaterial property damage.

CAUTION

Points to Observe for Safe Usage

4

USER AGREEMENTIn using this Removable Navigation Drive, NVE-P1 (hereinafter referred to as “System”), which includes AlpineElectronics, Inc. (“Alpine”) Specifications, Space Machine, Inc. ("Space Machine") Software and NAVTEQNorth America, LLC. (“NAVTEQ”) Database, you are bound by the terms and conditions set forth below. Bybreaking the seal on the System and using your copy of the System, you have demonstrated your agreementto the terms and conditions of this Agreement. You should, therefore, make sure that you read andunderstand the following provisions.

The System may not be copied, duplicated or otherwise modified, in whole or in part, without the expresswritten permission of Alpine, Space Machine and NAVTEQ.The System may not be transferred or sublicensed to any third party for profit, rent or loan or licensed forreuse in any manner.The System may not be decompiled, reverse engineered or otherwise disassembled, in whole or in part.The System may not be used in a network or by any other manner of simultaneous use in multiple systems.The System is intended solely for personal use (or internal use where the end-user is a business) by theconsumer.The System is not to be used for commercial purposes.Neither Alpine, Space Machine nor NAVTEQ guarantees to the customer that the System meet the specificobjectives of the user.Neither Alpine, Space Machine nor NAVTEQ shall be responsible for any damages caused by the use of theSystem to the actual user and to any third party.The warranty on the System shall not extend to an exchange or refund due to misspelling, omission of letters,or any other cosmetic discrepancy in layout found in the System.The right to use the System shall expire either when the user destroys this software, or when any of the termsfor use is violated and Alpine, Space Machine and/or NAVTEQ exercise the option to revoke the license touse this software.The terms and conditions hereof apply to all subsequent users and owners as well as to the originalpurchaser.

The NAVTEQ Database may include or reflect data of licensors, including Her Majesty The Queen in right ofCANADA. Such data is licensed on an “AS IS” basis. The licensors, including Her Majesty The Queen, makeno guarantees, representations or warranties respecting such data, either express or implied, arising by lawor otherwise, accuracy or fitness for a particular purpose. The licensors, including Her Majesty The Queen, shall not be liable in respect of any claim, demand or action,irrespective of the nature of the cause of the claim, demand or action alleging any loss, injury or damages,direct or indirect, which may result from the use or possession of the data or the NAVTEQ database. Thelicensors, including Her Majesty The Queen, shall not be liable in any way for loss of revenues or contracts,or any other consequential loss of any kind resulting from any defect in the data or the NAVTEQ database.End User shall indemnify and save harmless the licensors, including Her Majesty The Queen and the minister,and their officers, employees and agents from and against any claim, demand or action, irrespective of thenature of the cause of the claim, demand or action, alleging loss, costs, expenses, damages or injuries(including injuries resulting in death) arising out of the use or possession of the data or the NAVTEQdatabase.

5

TABLE OF CONTENTSPRECAUTIONS AND NOTICES . . . . . . . . . . . . . . . 2WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . 3USER AGREEMENT . . . . . . . . . . . . . . . . . . . . . 4TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . 5SYSTEM FEATURES . . . . . . . . . . . . . . . . . . . . . 6IN THE BOX . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Accessories . . . . . . . . . . . . . . . . . . . . . . . 7Optional Accessories . . . . . . . . . . . . . . . . . 7

COMPATIBLE MMS (MOBILE MULTIMEDIA STATION) . 8List . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Connection Chart . . . . . . . . . . . . . . . . . . . 8

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . 9Docking with IVA-W203 and IVA-W505 . . . . . 9Removing NVE-P1 from IVA-W203 and IVA-W505 . . . . . . . . . . . . . . . . . . . . . 9

How to Reset NVE-P1 . . . . . . . . . . . . . . . . .9How to Reset MMS . . . . . . . . . . . . . . . . . . .9

BASIC OPERATIONS . . . . . . . . . . . . . . . . . . . . 10To Power On . . . . . . . . . . . . . . . . . . . . . 10To Power Off . . . . . . . . . . . . . . . . . . . . . 10Set a Destination and Go! . . . . . . . . . . . . 10

MAP FUNCTION . . . . . . . . . . . . . . . . . . . . . . . 12Setting Estimate Time Display . . . . . . . . . 12Setting the Map Orientation . . . . . . . . . . . 12Repeating the Announcement . . . . . . . . . . 12Zoom In/Out Map . . . . . . . . . . . . . . . . . . 12GPS Status . . . . . . . . . . . . . . . . . . . . . . 12Accessing the MMS . . . . . . . . . . . . . . . . 12Setting a Destination Directly from Map Display . . . . . . . . . . . . . . . . . . 13Switching Map Display . . . . . . . . . . . . . . 13

MAIN MENU . . . . . . . . . . . . . . . . . . . . . . . . . 14DESTINATION . . . . . . . . . . . . . . . . . . . . . . . . 14

Setting a Destination by Address . . . . . . . . 14Setting a Destination by POI . . . . . . . . . . . 15Setting a Destination from theAddress Book . . . . . . . . . . . . . . . . . . . . . 17Setting a Destination by Recently Entered Destination . . . . . . . . . . . . . . . . 17

Setting a Destination by Coordinates . . . . . 17Setting a Destination by Intersection . . . . . 18Confirm Destination Screen . . . . . . . . . . . 19Finding Alternate Way . . . . . . . . . . . . . . . .19

OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Find Local Places . . . . . . . . . . . . . . . . . . 20Saving a Destination into the Address Book . . . . . . . . . . . . . . . . . 20

Setting Waypoints . . . . . . . . . . . . . . . . . . . . . 21HOME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Set Destination as Home . . . . . . . . . . . . . 22Going Home . . . . . . . . . . . . . . . . . . . . . . 22

ROUTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Recalling the Maneuver List during Guidance . . . . . . . . . . . . . . . . . . 23

Finding Alternate Route . . . . . . . . . . . . . . 23Deleting Route . . . . . . . . . . . . . . . . . . . . 23Waypoints . . . . . . . . . . . . . . . . . . . . . . . 23

EDIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24Editing Home . . . . . . . . . . . . . . . . . . . . . 24Editing Address Book . . . . . . . . . . . . . . . 24Deleting Previously Saved Destinations . . . 24

MOBILE PHONE . . . . . . . . . . . . . . . . . . . . . . . 26Placing Calls . . . . . . . . . . . . . . . . . . . . . . 26Receiving Calls . . . . . . . . . . . . . . . . . . . . 27Call Option Menu . . . . . . . . . . . . . . . . . . 27

SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28Customizing Display . . . . . . . . . . . . . . . . .28Customizing Guidance . . . . . . . . . . . . . . . .29Setting up the Clock . . . . . . . . . . . . . . . . .29Changing Unit of Measure . . . . . . . . . . . . .29Configuring System Settings . . . . . . . . . . .29Bluetooth Setup . . . . . . . . . . . . . . . . . . . 30Viewing Information . . . . . . . . . . . . . . . . . 32

IN CASE OF DIFFICULTY . . . . . . . . . . . . . . . . . 34How to Update the New Software and MapDatabase . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . 35INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . 37

6

SYSTEM FEATURES

Mini USB Connector

External GPSAntenna Connector

Reset Button

Power Indicator

SoftwareUpdate Switch

System InterfaceConnector

Removable Navigation Drive, NVE-P1

Congratulations and thank you for purchasing the Alpine Removable NavigationDrive, NVE-P1. We hope you enjoy using this exciting product and trust that it willmake your driving experience more comfortable, stress-free, and entertaining. TheRemovable Navigation Drive, NVE-P1 provides an easy-to-use user interface,clear, easy-to-understand spoken driving instructions, and award winning designall in a portable product. NVE-P1 is built upon Alpine's history of navigationsuccess in North America. Please read this manual carefully. If you have anyfurther questions about NVE-P1’s operation, feel free to call Alpine at 1-888-NAV-HELP (628-4357) for technical assistance.

7

IN THE BOX

■ Optional Accessories

■ Accessories

USB Cable

NVE-P1

Quick Reference Guide

Removable Navigation Drive

Quick Reference Guide

External GPS Antenna External Microphone

R Customer Care Registration For easy on-line registration, go to “www.alpine-usa.com/registration”Thank you for choosing Alpine! Please register your product with us so we can serve you better.

Product purchased1. Cassette Player 9. Monitor Controller2. CD Player 10. Video Monitor3. MD Player 11. Navigation4. DVD Player 12. Mobile Mayday5. CD Changer 13. Video Tape Player6. Amplifier 14. Processor/Equalizer7. Speaker 15. Security8. Subwoofer 16. Other

Model Number:

Serial Number:

Date of Purchase:Month: Year:

If navigation system, which monitor?

1. Alpine (Model No.)

2. Other (Brand Name)

Purpose of buying this unit?1. Addition2. Replacement Previous brand replaced?

1. Factory installed2. Alpine3. Other

Have you purchased Alpine products before?1. First time 2. Two or more times

First name:

Last name:

Home address:

May we contact you at this address? 1. Yes 2. No

Phone number: ( )

May we contact you at this number? 1. Yes 2. No

E-mail Address:May we contact you by e-mail? 1. Yes 2. No

Gender 1. Male 2. Female

Date of Birth Month: Year:

Marital Status 1. Single 2. Married

Which ethnicity best describes yourself:1. Caucasian 4. Asian2. Hispanic 5. Other 3. African-American

Your highest level of education completed:1. High School Student2. High School Graduate3. 2 Yr. Degree/Some College4. Completed 4 Yr. College5. Completed Graduate School

When you purchased this Alpine unit, did youcompare it with other brands?1. Yes 2. No.

(Brand Name)

Which of the following statements best describes you?1. I usually have more electronic equipment than my friends2. I am usually one of the first of my friends to buy the newest

electronic equipment3. I usually wait until a product has been out for a while before

I purchase it4. I am usually on of the first of my friends to know about the

newest car5. I usually know more about cars than my friends

Occupation1. Executive/Managerial 6. Engineering/Technical2. Secretarial/Clerical 7. Farming/Fishing3. Sales 8. Retired4. General Labor 9. Student5. Professional 10. Other

Household Income1. Less than $30,000 4. $70,000 - $90,0002. $30,000 - $50,000 5. $90,000 - $110,0003. $50,000 - $70,000 6. Over $110,000

Type of vehicle in which this unit is installed.Make: Model:

Purchased Year: Model Year:

How was this vehicle purchased?1. Bought 2. Leased

Thank you for your cooperation! We value your privacy. This information will remain confidential with Alpine and its affiliates. PART NO. 68P04190K17-A

Street address

State/Prov. Zip CodeCity

SE

AL

HE

RE

SE

AL

HE

RE

Customer Care Registration is for Product registration.Failure to complete and return this card does not diminish your warranty rights.

Registration Card

Owner’s Manual CD

The following accessories are available from your authorized Alpine dealer.

1. PMD-DOK2 – Enables docking of NVE-P1 to any Alpine MMS (MobileMultimedia Station) that does not have the Direct Docking feature.

2. PMD-ANT1 – An external GPS antenna hard-wired to NVE-P1 used ininstances where you cannot normally receive GPS signals inside the car, dueto metallic window tint, etc.

3. RUE-4140 – A combination navigation and audio remote control that allowsyou to control most of the navigation features wirelessly.

PMD-B200 PMD-DOK2

NVE-P1

2DIN MMS(DOCK N’ ROLL)

IVA-W505IVA-W203IVA-W205IVA-Dxxx

DIRECTDOCK-IN

with DOK2

with DOK2

DIRECTDOCK-IN

DIRECTDOCK-IN

DIRECTDOCK-IN

DIRECTDOCK-IN

NODOCKABLE

PMD-DOK2

DOCKINGSTATION

1DINMMSPRODUCT

NAME

or w/DOK2 or w/DOK2 or w/DOK2

or w/DOK2 or w/DOK2 or w/DOK2

8

COMPATIBLE MMS (MOBILE MULTIMEDIA STATION)

Note: NVE-P1 is not compatible with IVA-W205.

■ List

GPS ANT

GPS ANTExt. MIC

IVA-W203/505 (2DIN DOCK MMS)

IVA-Dxxx series (1DIN MMS)

Ext. MIC

PWR

PMD-DOK2 (Docking Station)

NAV

AUDIO

NVE-P1

RDS ANT(EU only)

NVE-P1

RDS ANT(EU only)

P1 Connecting to 1DIN MMS

P1 Connecting to 2DIN MMS

■ Connection Chart

9

INSTALLATION

■ How to Reset NVE-P1In the event the system requires a reset, pull over in a safe and legal manner beforedoing so. Press the reset button on the NVE-P1 for at least 1 second.

■ How to Reset MMSIf you change NVE-P1 to PMD-B200 (or PMD-B200 to NVE-P1), both IVA-W203 andIVA-W505 need to be reset before beginning the docking process. See the owner's manual of MMS for detail.

■ Docking NVE-P1 to IVA-W203 and IVA-W505

■ Removing NVE-P1 from IVA-W203 and IVA-W505Press Open button of 2 DIN MMS face and toucheither Open or Eject on the screen.

Press the eject button on the right side of 2 DINMMS inside face.

Remove NVE-P1 from 2 DIN MMS.3

2

1

CLOSE

1

2

Press Open button of 2 DIN MMS face and touchOpen on the screen.

Insert NVE-P1 into the unit with Alpine logo facingup (reset button on the right).

Press firmly into place.

Touch Close on the screen to close 2DIN MMSface.

Select Navigation as a source.5

4

3

2

1

CLOSE

1

2

Disclaimer screen appears.Read carefully. Touch IAccept to display map.

The last-known currentlocation is indicated onthe map.

To Power OffPress and hold Power (Source)button of MMS for 2 seconds.

To Power On1

3

4

10

Select an input method.(In this example, Places isselected.)

2

Select a search method.(In this example, By POICategory is selected.)

3

Touch Main Menu .Select Destination from Main Menu.

1

The following example briefly describeshow to input a destination.The Route button is grayed out if Homeaddress or Destination have not beenset. Car must be parked when usingEdit and Setup feature.

BASIC OPERATION

Set a Destination and Go!Press the POWER (Source)button to turn on the MMS.

2 Select Navigation onthe MMS screen.

Confirmation screenappears if a destinationwas set prior to the lastshutdown. Click OK tocontinue to the previousdestination.

5

11

Map is displayed.Follow the navigation.

9

Select OK to Proceed toset the destination.

8

For Map Function, see page 12.To Go Home, see page 22.To Find other routes, see page 23.

Select the search method.(In this example, By POIName is selected.)

5

Type name of a place. If more than one place with thesame name exist, sort methodscreen appears.

6

Select the place withcorrect address.

7Scroll the list. Select desired category. (In this example, ATTRACTIONSis selected.)

4

BASIC OPERATION

12

Click this icon to switch betweenEstimated Time Remaining andEstimated Time of Arrival.

Note: The time estimates arebased on the average speed. Theestimate time will vary dependingon vehicle speed. The arrow alwayspoints toward the destination.

In north up view, north is always atthe top of the display. This makes iteasy to determine your currentheading with respect to the map.

In heading-up view, the currentdirection is always pointing to thetop of the display. This makes iteasy to see the direction of thenext turn on the map.

The 3D View offers you a morerealistic perspective by tilting themap and displaying it with a horizonline. Streets are displayed as youapproach them instead of from abirds-eye view.

Setting the Map Orientation

Setting Estimate Time DisplayClick icon to repeat the guideannouncement.

Click icon to display scroll bar.

Touch ▲▼ or blue bar to zoom themap in or out.The scroll bar disappearsautomatically after 2 seconds.

Repeating the Announcement

Zoom In/Out Map

GPS StatusClick icon to view GPS receivingcondition information from satellite.

Distance tonext maneuver

Next Street NameNext ManeuverArrow

MapOrientation

Direction toDestination

Estimated TimeRemaining (ETR) /Estimated Time of

Arrival (ETA)

GPS Status barCurrent Street

NameVoice PromptRepeat Button

Current PositionIcon and Map /Split / ArrowButton

Map Scale Bar

Main MenuButton

North Up

HeadingUp

3D View

Click icon to switch between North up, HeadingUp and 3D Views.

MMS Access Button

Accessing the MMSClick icon to access the MMSdisplay control.

Note: If left idle for more than 5 seconds, thesystem will automatically return to the navigationscreen.

BluetoothStatus Icon

(See page 31)

MAP FUNCTION

13

Touch anywhere on map screen.The current location arrow changes to CrosshairCursor on the screen.

Move the cursor to the new desiredstreet.Note: Use Map Scale Bar to zoom out the map if the destination is far from the current location.

Touch Select.

Select Set as Destination.

Touch OK to Proceed on theconfirmation screen.Note: To use other functions on the confirmation screen, see page 19 for details.

5

4

3

2

1

MAP FUNCTION■ Setting a Destination Directly from Map Display

To cancel, touchPrevious Screen

icon.

Touch the Current Position to switch between Map and Arrowmodes.

Switching Map Display

Arrow ModeDisplays three-successive arrowmaneuvers all theway to yourdestination whileproviding turn-by-turn guidanceprompts.Map Mode

Shows a full-screenmap of the area whileproviding turn-by-turnguidance prompts.

Split Arrow/Map Mode

Displays a largearrow and largernext-street-namefont along side amap screen whileproviding turn-by-turn guidanceprompts.

14

MAIN MENU

Get back home fromanywhere.➔ Page 22

Set and saveDestinations. ➔ Page 14

Access your Bluetoothpaired mobile phone.➔ Page 26

Edit Home andAddress Book.➔ Page 24

Customize thenavigation system.➔ Page 28

Modify or choosealternate routes to adestination.➔ Page 23

Select Input City Name.Note: You can avoid typing the city name byselecting Recent Cities. A list of recently entered city names will display.Select the desired city.

Type the first few characters of the city name and press OK. If there are unique matches, the system willautomatically display a short list of city names.Select the desired city.

Type the characters of the street name.

Touch OK. The list of applicable street names appears. Selectthe desired street.

Type the address number and touch OK.

Confirmation screen appears. Touch OK toProceed to set the destination and startguidance. See page 19 for detail.

6

5

4

3

2

DESTINATION■ Setting a Destination by Address

Go to Main Menu

➔ Destination ➔ Address1

15

You can select from approximately 1.3 Million Point-of-Interest (POI) locations storedinside your Removable Navigation Drive, NVE-P1. These destinations are sorted by POIName or by POI Category and are listed in order of distance from your current location.

Destination by POI Name

Go to Main Menu

➔ Destination ➔ Places

Select By POI Name.

Type the desired place name. Touch OK. A list of place names appears. Note: You can also perform a Keyword Search byentering a portion of your desired place name. Thelist of destinations that appears will include all placenames containing the keyword you entered.

Use the arrows to the right of the list tomove the yellow highlight.This will show detailed address information and phone number (if available) for each entry in the Places database.

Select the place with correct address.For emergency locations such as Police Stations,Hospitals, etc., please verify availability beforeproceeding to such locations.

Confirmation screen appears. Touch OK toProceed to set the destination and startguidance. See page 19 for detail.

6

5

4

3

2

1

DESTINATION■ Setting a Destination by POI

16

Go to Main Menu

➔ Destination ➔ Places

Select By POI Category.

Select a desired POI Category. There are 37 POI categories to choose fromincluding ATMs, Banks, Gas Stations, GroceryStores, Hotels, Parking Lots, Restaurants and more.

Select Search Method.4

3

2

1

DESTINATIONDestination by POI Category

Sort by Distance

By POI Name

Within a City

Touch Near Here to see the list of placesfrom the current vehicle position or touchNear Destination to see the list nearyour destination.

Select the place.

Confirmation screen appears. Touch OKto Proceed to set the destination andstart guidance.*1

7

6

5

Follow 3 to 5 in “Destination by POI Name” on Page 15.5

Type the city name and select a city.

The list of POIs appears in order of the distance from the selected city. Select the desired place.

Confirmation screen appears. Touch OK toProceed to set the destination and startguidance. *1

*1 See page 19 for detail.

7

6

5

17

Go to Main Menu

➔ Destination ➔ Address Book

Select the desired destination.

Confirmation screen appears.

Touch OK to Proceed to set the destination and start guidance.To save an address in the address book, see page 20.

3

2

1

■ Setting a Destination from the Address Book

Go to Main Menu

➔ Destination

➔ Coordinate

Enter the Latitude of your destination.Touch OK.

Enter the Longitude of your destination. Touch OK.

Confirmation screen appears. Touch OK to Proceed to set the destination and start guidance. *1

*1 See page 19 for detail.

4

3

2

1

Go to Main Menu

➔ Destination

➔ Recent

The list of recent destinations appears. Select the destination.

Confirmation screen appears. Touch OK to Proceed to set the destination and start guidance. *1

3

2

1

DESTINATION

■ Setting a Destination by Recently Entered Destination

■ Setting a Destination by Coordinates

18

Go to Main Menu

➔ Destination

➔ Intersection

1

Select Input City Name.

Note: You can skip typing the city name byselecting Recent Cities. It displays a list of recent city names previouslyentered.

Type the city name, then select the cityfrom the list.

Type the first street name. Touch OK. The list of applicable street names appears. Select the desired street.

Input the second street name.If there is only one street crossing with the firststreet, the name of the street automaticallyappears.Confirm City name if there are more than 1 citeswith the same intersection.

Confirmation screen appears. Touch OK to Proceed to set thedestination and start guidance. See page19 for detail.

6

5

4

3

2

DESTINATION■ Setting a Destination by Intersection

19

DESTINATION

Call(Only available on POIs and address book)If the phone number is available, youcan call the selected location usingyour Bluetooth enable mobile phone.

Changing StateIf you want to choose a differentstate from the one shown on thescreen, touch Change toswitch to a different state.

Selecting Letters

Delete one letter

Selectedcharactersare displayed.

Add one spaceType numbers

MapCheck the destination on themap. Touch to go back tothe confirmation screen.

Type accentuatedcharactersType punctuationmarks

OK to ProceedSet the destination anddisplay a map.

OptionFind Local POI ➔ Page 20Set as Waypoint ➔ Page 21Save in Address Book ➔ Page 20

■ Confirm Destination Screen

■ Finding Alternate WayChange MethodYou can choose and re-calculate a differentroute based on Quickest Route withMaximize/Minimize Highway, ShortestRoute, with/without Ferry and/or Toll Road.

■ Saving a Destination into the Address Book

OPTIONS■ Find Local Places

Touch anywhere on map screen.The current location arrow changes to cross hair cursor on the screen.

Touch Select.

Select Find Local POIs and the desired category.

Select the desired place.

Confirmation screen appears. Touch OK to Proceed to set thedestination and start guidance. See page 19 for detail.

5

4

32

1

The navigation system can display Points of Interest (POI) around the cursor position,when you scroll the map. As with POI categories, with the local places search youcan choose from 37 categories including ATMS, Banks, Gas Stations, GroceryStores, Hotels, Parking Lots, Restaurants and more.

How to Find Local POIs Directly from the Map

How to Find Local Places from the Destination Menu

Set a destination first from Destination

On the confirmation screen, touch Option.

Follow steps 3 to 5 above in “How to Find Local POIs Directlyfrom the Map”.

3

2

1

You can also find local places from the Destination Menu.

Any destination can be saved into the Address Book.

Select a destination using any method.

From the confirmation screen, selectOption.

Touch Save in Address Book.

“Input Name” screen appears. Type the desired name and touch OK.Note: For the details of selecting letters, see page 19.

System returns to the Main Menu screen.Note: To display the saved destination on themap, see page 17, “Setting a Destination from theAddress Book”. Address book can hold up to 500entries.

5

4

3

2

1

20

21

OPTIONS■ Setting Waypoints

Touch anywhere on map screen.The current location arrow changes to cross hair cursor on the screen.

Move the cursor to the desired waypoint.

Touch Select.

Select Set as Waypoint then selectRecalculate.

When the route search is complete, the current location is displayed. The map navigates you to the first waypoint.

5

4

3

2

1

How to Set a Waypoint from the Destination Menu

How to Set a Waypoint Directly from Map

You can set up to 10 waypoints between your current location and your destination. Thefinal destination must be set before entering any waypoints.

You can also find local places from Destination Menu.

Enter your desired destination by using the method on pages 14through 19 from Destination Menu.

On the confirmation screen, select Option.

Select Set as Waypoint and select Recalculate.3

2

1

Enter in a destination from the Address Book, see page 16.

On the confirmation screen, touch Option ➔ Set as Waypoint.

Touch Recalculate to recalculate a route which includes yourwaypoint.

3

2

1

How to Set a Waypoint from the Address Book

Set a waypoint by following the process above.

On the waypoint screen, select Edit.

Change the order of waypoints by touching the arrow button on thebottom of the navigation screen.Touch Delete to remove the waypoint.

Touch Calculate to calculate a route which includes your waypoint.4

3

2

1

How to Edit a Waypoint

22

Go to Main Menu

➔ HomeConfirmation screen appears. TouchOK to Proceed to set the destinationand start guidance. See page 19 fordetail.

To edit the Home Address, see page 24.

2

1

HOME■ Set Destination as HomeYou can get home from anywhere once the home address is set from DestinationMenu.

Set the destination using any desiredmethod.On the confirmation screen, touchOption.Touch Set as Home Location.3

2

1

■ Going Home

23

ROUTE■ Recalling the Maneuver List during Guidance

Go to Main Menu

➔ Route

Touch Maneuver List.

List of upcoming streets and turnsappears on the screen.

To preview a specific point, select a street name/maneuver on the list.

32

1

■ Deleting RouteGo to Main Menu➔ Route ➔ Delete ➔ YesNote: After deleting the destination, you cannot select Route Menu until the next destinationis set. To set up the destination, see DestinationMenu on page 14.

■ WaypointsSee page 21 to set Waypoints.

You can view a list of street names and upcoming turns and streets.

■ Finding Alternate Route See page 21 to set alternate route.

24

Go to Main Menu ➔ Edit

Touch Edit Address Book

The list of addresses appears.Select the destination you need to modify.

“Edit Address Item” screen appears. See page 25 for details.

Note: Select DELETE ALL to delete all addresses saved in the address book.

4

3

2

1■ Editing Address Book

■ Deleting Previously Saved DestinationsGo to Main Menu ➔ Edit

Touch Delete Previous Destination.

Select destination you need to delete.

Touch YES to delete the destination on the confirmation screen.

Note: Select DELETE ALL to delete all recently entered destinations.

4

3

2

1

EDIT

■ Editing HomeGo to Main Menu➔ Edit

Touch Edit Home.

“Edit Home” screen appears.See page 25 for details.

3

2

1

Locations and Home addresses saved in the Address Book can be edited for quickrecall. Also information including phone numbers and icons can be modified.

25

Edit Telephone Screen

Delete Screen

Change Icon Screen

Name Touch Name to change thedisplay name of the storedlocation.

Note: For the details of selecting letters, see page 19.

Tel Touch Tel to change thetelephone number of the storedlocation.

Map Touch Map to preview thelocation on the map.To go back to Edit Menu,

Main Menu ➔ Edit

Delete Touch Delete to delete the storedlocation.

Icon Touch Icon to change the icon ofthe stored location on the map.

Input Name Screen

EDIT

26

MOBILE PHONEMost Bluetooth enabled mobile phones can be synchronized to interface with NVE-P1.Once you have paired and synchronized your mobile phone with NVE-P1 (see Setupon page 30) you can place and receive calls in addition to many other convenientfunctions. Some Bluetooth enabled phones may not be compatible and some featuresmay not be available even after synchronizing and pairing.Note: It may take a few minutes for information to transfer from your phone to NVE-P1.

■ Placing CallsTouch Main Menu

Touch PhoneNote: If Bluetooth is OFF, a message indicatingthat Bluetooth is turning on will be displayed.After Bluetooth is ON, if your phone is notconnected, the Bluetooth Discover Modemessage will be displayed. Please refer to Bluetooth Setup on page 30 fordetails.

Using the 12 key Dial Pad

Touch Dial.

Enter the number and touch Call.

Using your Phonebook Phonebook will be available after downloading hasbeen completed.

Touch Phonebook.Begin entering the name of the contact you wish to call.A list will appear.

Select the desired contact from the list.Confirmation screen appears with the contact’s detailed information.

Touch Dial to place the call.6

5

43

4

3

2

1

X-XXX-XXX-XXXX

X-XXX-XXX-XXXXX-XXX-XXX-XXXXX-XXX-XXX-XXXXX-XXX-XXX-XXXXX-XXX-XXX-XXXX

27

MOBILE PHONEUsing Dialed, Missed, or Received Calls from your call historyCall History will be available after downloading has been completed.

Touch Main Menu

Touch Phone

Touch Dialed Calls, Missed Calls, or Received Calls.A list of your call history will appear.

Select the desired contact from the list. Confirmation screenappears with the contact’s detailed information if available.

Touch Dial to place the call.

Note: You can continue to use NVE-P1 during an active call. Touch the icons to jump to theMap or Main Menu screens. Touch the green phone icon to return to the call menu.

■ Receiving CallsWhen your mobile phone is actively paired with NVE-P1, a pop-up window willappear when you have an incoming call. The caller ID number will be displayed whenavailable. Touch Answer to accept the call or Ignore to ignore it.

■ Call Option MenuDuring an active call touch the green phone icon to access the Call OptionMenu. This menu displays the Caller ID Name, Phone Number, and Call Duration.The following options are also available from this menu:

MuteThis allows you to temporarily mute the microphone so you can still hear the caller,but the caller cannot hear you.

Transfer Call to PhoneYou can transfer the call from NVE-P1 to your mobile phone for greater flexibility.

End CallThis ends the current phone call.

Note: After ending a call you will automatically be returned to the previous menu.

5

4

3

2

1

28

Go to Main Menu

Select Setup

Setup screen appears.3

2

1

SETUP

■ Customizing Display

Setting the Map Color Day - a bright tone screenNight - a dark tone screenAuto - switches automatically between

Day and Night modes dependingupon ambience brightness

Map Style1 - Geographic features displayed in

light gray colors (Default)2 - Geographic features displayed in

dark brown colors3 - Geographic features displayed in

dark gray colors4 - Geographic features displayed in

light brown colors

Background ColorYou can select from 4 backgroundcolors (blue, green, purple and black) forall menu screens.

Displaying and Editing Icons on theMapPOI Icons, the Home Icon and Iconsused in the Address Book can be turnedon and off from the Display Setup Menu.You can also change these icons.

TrailThe Trail feature allows you to turn onand off trail dots that appear whereverthe vehicle icon traverses. This isespecially helpful for off-roadenthusiasts.

Display AdjustmentThe Adjust button is active only whenNVE-P1 is docked into IVA-W203 orIVA-W505, or connected to thedocking station, PMD-DOK2. It willallow you to make minor alignmentadjustments (up/down/left/right) to thedisplay of the docked image.

You can check status or customize Display,Guidance, Clock, Measuring Unit settings fromthe Setup Menu. You can also Turn Demo Modeon and off.

29

■ Customizing GuidanceTurning Voice On and Off This allows you to turn ON or OFF guidance voice prompts.

Changing Navi Mix VolumeThis allows you to vary the volume of the voice prompts with respect to the music.

Setting Estimate Time DisplayEstimated Time of Arrival (ETA) or Estimated Time Remaining (ETR) can be set here.You can also change between ETA and ETR directly in the map screen. See page 12.

■ Setting up the ClockYou can set the Time Zone and Daylight Savingsetting to fit your region.

■ Changing Unit of MeasureYou can choose the unit of measure between Milesand Kilometers.

■ Configuring System SettingsReset All SettingsThis allows you to delete all stored information anddefault back to the original factory settings.

SETUPGo to Main Menu

Select Setup

Setup screen appears.3

2

1

30

■ Bluetooth SetupBluetooth enabled mobile phones can be paired to interface with NVE-P1. You cancustomize this interface using the Bluetooth Setup controls.

Go to Main Menu

Select Setup

Select Bluetooth.The Bluetooth Setup menu appears anddisplays the setup options. Use the largearrow button at the bottom of the screen toview additional options. All Bluetooth setupoptions are detailed below.

Turning Bluetooth On and OffThis allows you to turn the Bluetooth functionality on or off.

Starting Discover ModeDiscover Mode allows your mobile phone to pair with NVE-P1. Start Discover modeto begin the initial pairing process. Follow your individual phone’s instructions forpairing.

Auto ConnectTurning Auto Connect on will allow the last connected phone to automaticallyconnect with NVE-P1 whenever they are in range and both have Bluetooth turnedon.

Auto AnswerThis allows NVE-P1 to automatically answer allincoming calls for you after the first ring.

PhonebookThis allows you to store your phone addressinto NVE-P1.

Changing Device NameThe device display name can be set here by selecting Change.

SETUP

1

2

3

31

Changing Device PasskeyThe passkey used to pair NVE-P1 with your mobilephone can be changed here.

Default Passkey is '0000'.

Bluetooth IndicatorThe following icons indicate the Bluetooth status:

No Icon When Bluetooth is OFF, the icon does not appear.

When Bluetooth is on, but not paired, the gray icon appears.By pressing the icon, “Discover Mode” screen appears.

When Bluetooth is on and connected, the blue icon appears.By pressing the icon, “Call” screen appears.

When a phone call is active, a green phone icon appears.

Pairing Your Mobile Phone with NVE-P1 Go to Bluetooth Setup and turn on Bluetooth.

Start Discover Mode.

On your mobile phone, make sure Bluetooth is on, then searchfor Bluetooh devices.

Select NVE-P1 name and enter the passkey shown on theNavigation screen.

When your mobile phone is connected the message, "Syncingphone..." appears momentarily, then the Bluetooth icon appearsin blue.

When the address book is downloaded, the message, "Syncingphone data complete." appears momentarily.

6

5

4

3

2

1

SETUP

32

■ Viewing InformationSimulating NavigationYou can watch a demonstration of the navigation system’s voice and screen guidance.Note: Set your destination first before using this function.

To Start a Demonstration

To Stop a Demonstration

Follow 2 through 4 of "To Start aDemonstration".

Select Stop Demo.

The demonstration will end.3

2

1

Viewing Trip InformationThe odometer displays the route distanceand time traveled.

Go to Main Menu

Go to Setup

Select Information.

Select Trip Info.4

3

2

1

Driving Average Average speed since Trip Info was reset.

Overall Average Average speed since start of trip.

Maximum Speed Maximum speed reached on this trip.

Driving Time Time vehicle has been moving since the trip was reset.

Idle Time Time vehicle has been stopped (not moving) since the trip was reset.

Total Time Total elapsed time on the trip which is always the driving time plus idle time

Setup a route.

Go to Main Menu Go to Setup

Select Information.

Select Start Demo.Demonstration starts.6

5

4

3

2

1

SETUP

33

Go to Main Menu

Go to Setup

Select Information.

Select GPS Status.4

3

2

1

You can view the dynamic location informationreceived from satellite such as signal strength,compass (direction information), latitude/longitude,approximate altitude, and speed. This featureallows you to view GPS satellite signal information.An explanation of the messages is shown below.

“Locating GPS Satellites”: NVE-P1searches the sky looking for GPS satellites.

“Acquiring GPS Signal”: NVE-P1acquires positioning information transmittedfrom 1 to 3 tracked satellites whilesearching for more satellites (minimum 4needed).

“Fixing GPS Position”: NVE-P1 requirescontinuous signals from 4 or more trackedsatellites (for 30 seconds) in order toaccurately fix your position.

“Temporary Poor GPS Coverage”:Thunderstorms, dense foliage orsurrounding tall buildings may causetemporary loss of position fix (acceptable ifunder 30 seconds).

“Poor GPS Signal, Lost Position Fix”:You may have entered an area whereconsistently poor GPS signal (lasting 30seconds or more) makes it impossible tomaintain a position fix.

“No Line of Sight, Lost GPS Tracking”:You are in an area where line of sight toGPS satellites has been blocked.

Go to Main Menu

Go to Setup

Select Information.

Select System Info.4

3

2

1

You can check software application, databaseversion, and other information in this screen.Make a note of this information and refer to itwhenever you communicate with Alpine TechSupport or your Alpine authorized dealer.

Viewing GPS Status

Viewing System Information

The following messages are displayed while the GPS receiver is tracking satellites:

SETUP

34

If you encounter a problem, please review the items in the following checklist. This guidewill help you isolate the problem if the unit is at fault. Otherwise make sure the rest of yoursystem is properly connected, batteries are completely charged and contact yourauthorized Alpine dealer or Alpine directly at 1-888-NAV-HELP (1-888-628-4357).Unable to use Phone feature.

Some Bluetooth enabled phones may not be compatible and some features may not beavailable even after synchronizing and pairing.

The vehicle’s position is erroneous.Reset the unit and drive the vehicle in an area of good GPS reception to allow the unitto recalibrate itself. Move to a location where strong GPS reception is possible.

No operation· Moisture condensation ➔ Allow enough time for the condensation to evaporate

(about 1 hour).· Ambient temperature ➔ Lower the temperature in the vehicle to below 113°F (45°C)

over 113°F (45°C) by driving with the windows open or air conditioner on.

The unit is taking a long time to acquire GPS signal. It may take a long time for the unit to acquire GPS signal if it has been powered on inan area that is more than 200 miles from the area where it was last powered off.

■ How to Update the New Software and Map DatabaseUsing your home PC, NVE-P1 can be updated with the latest mappingand Point of Interest information. Please refer to instructions includedwith the update software on how to upgrade your NVE-P1.For additional information on the update software, please visit ourwebsite at; http://www.alpine-usa.com or contact customer service 1-888-NAV-HELP (1-888-628-4357).

IN CASE OF DIFFICULTY

35

SPECIFICATIONSMain Unit Size 6.1” x 2.9” x 1.0” (145mm x 73mm x 26mm)

Main Unit Weight 4.4 oz (120 g)

CPU Centrality Atlas III ARM9 CPU

GPS Embedded 16 channel GPS, Built-In Main Unit Antenna with Optional External AntennaConnection

Storage Media Built-In memory with Pre-Loaded Maps of US* and Canada and 1.3 Million Points ofInterest Locations

USB Interface 2.0

Power Requirements 5V 1A

Operating Temp 14˚F to 158˚F (-10˚C to +70˚C)

Storage Temp 4˚F to 185˚F (-20˚C to 85˚C)

Resolution QWVGA 400 x 234 pixels

Note: Due to continuous product improvement, specifications are subject to change withoutnotice.

36

INDEXAAccessories 7Address book 20Announcement 12

BBackground Color 28Basic Operation 10Bluetooth 26, 30

Setup 30

CCall 26, 27

Ending 27Muting 27Placing 26Receiving 27

Clock 29Confirm Destination Screen 19Coordinates 17Customizing

Display 28Guidance 29

DDeleting

Route 23Saved Destination 24

DestinationSetting by Address 14Setting by Coordinates 17Setting by Intersection 18Setting by POI 15Setting by Previous Destination 17Setting from the Address Book 16Setting From Map Display 19

Detour 19

EEdit 24

Address Book 24Deleting Saved Destination 24Home 24

Estimate Time Display 12, 29

FFCC Compliance Statement 2

GGPS Status 12, 33HHome 22

Editing 24Finding a Way 22

IIcon 25In Case of Difficulty 34Index 36Information 32

GPS Status 33Simulating Navigation 32System Information 33

Trip Information 32Installation 9

MManeuver List

Recalling during Guidance 23Map Color 28Map Display 13Map Function 12

Announcement 12Battery Status 12Estimate Time Display 12GPS Status 12Map Display 13Map Orientation 12Set a Destination 13Zoom In/Out Map 12

Map Orientation 12Measuring Unit 29

OPPOI 15, 16

Local POI 20Power 10Precautions And Notices 2

RRepeating the Announcement 12Reset 9Route 23

Alternate Route 19Delete Route 23Detour 19Recalling the Maneuver List duringGuidance 23

SSaving a Destination into the Address

Book 20Set a Destination and Go! 10Setup 28

Clock 29Display 28Guidance 29Measuring Unit 29System Settings 29

Simulating Navigation 32Specifications 35System

Features 6Information 33Settings 29

TTable of Contents 5Trail 28Trip Information 32Troubleshooting 34

UUpdate 34

User Agreement 4

VVoice 29Volume 29

WWarnings 3Warranty 37Waypoints 21

ZZoom In/Out Map 12

●PRODUCTS COVERED:This Warranty covers Car Audio, Navigation Products andRelated Accessories ("the product"). Products purchased in theCanada are covered only in the Canada. Products purchased inthe U.S.A. are covered only in the U.S.A.

●LENGTH OF WARRANTY:This Warranty is in effect for one year from the date of the firstconsumer purchase.

●WHO IS COVERED:This Warranty only covers the original purchaser of the product,who must reside in the United States, Puerto Rico or Canada.

●WHAT IS COVERED:This Warranty covers defects in materials or workmanship (partsand labor) in the product.

●WHAT IS NOT COVERED:This Warranty does not cover the following:1 Damage occurring during shipment of the product to Alpine

for repair (claims must be presented to the carrier).2 Damage caused by accident or abuse, including burned voice

coils caused by over-driving the speaker (amplifier level isturned up and driven into distortion or clipping).Speaker mechanical failure (e.g. punctures, tears or rips).Cracked or damaged LCD panels. Dropped or damaged harddrives.

3 Damage caused by negligence, misuse, improper operation orfailure to follow instructions contained in the Owner's manual.

4 Damage caused by act of God, including without limitation,earthquake, fire, flood, storms or other acts of nature.Any cost or expense related to the removal or reinstallation ofthe product.

5 Service performed by an unauthorized person, company orassociation.

6 Any product which has the serial number defaced, altered orremoved.

7 Any product which has been adjusted, altered or modifiedwithout Alpine's consent.

8 Any product not distributed by Alpine within the United States,Puerto Rico or Canada.

9 Any product not purchased from an Authorized Alpine Dealer.

●HOW TO OBTAIN WARRANTY SERVICE:1 You are responsible for delivery of the product to an

Authorized Alpine Service Center or Alpine for repair and forpayment of any initial shipping charges. Alpine will, at itsoption, repair or replace the product with a new orreconditioned product without charge. If the repairs arecovered by the warranty, and if the product was shipped to anAuthorized Alpine Service Center or Alpine, Alpine will pay thereturn shipping charges.

2 You should provide a detailed description of the problem(s) forwhich service is required.

3 You must supply proof of your purchase of the product.4 You must package the product securely to avoid damage

during shipment. To prevent lost packages it is recommendedto use a carrier that provides a tracking service.

●HOW WE LIMIT IMPLIED WARRANTIES:ANY IMPLIED WARRANTIES INCLUDING FITNESS FOR USEAND MERCHANTABILITY ARE LIMITED IN DURATION TO THEPERIOD OF THE EXPRESS WARRANTY SET FORTH ABOVE ANDNO PERSON IS AUTHORIZED TO ASSUME FOR ALPINE ANYOTHER LIABILITY IN CONNECTION WITH THE SALE OF THEPRODUCT.

●HOW WE EXCLUDE CERTAIN DAMAGES:ALPINE EXPRESSLY DISCLAIMS LIABILITY FOR INCIDENTALAND CONSEQUENTIAL DAMAGES CAUSED BY THE PRODUCT.THE TERM "INCIDENTAL DAMAGES" REFERS TO EXPENSES OFTRANSPORTING THE PRODUCT TO THE ALPINE SERVICECENTER, LOSS OF THE ORIGINAL PURCHASER'S TIME, LOSSOF THE USE OF THE PRODUCT, BUS FARES, CAR RENTALS OROTHERS COSTS RELATING TO THE CARE AND CUSTODY OFTHE PRODUCT. THE TERM "CONSEQUENTIAL DAMAGES"REFERS TO THE COST OF REPAIRING OR REPLACING OTHERPROPERTY WHICH IS DAMAGED WHEN THIS PRODUCT DOESNOT WORK PROPERLY.THE REMEDIES PROVIDED UNDER THIS WARRANTY AREEXCLUSIVE AND IN LIEU OF ALL OTHERS.

●HOW STATE/PROVINCIAL LAW RELATES TO THE WARRANTY:This Warranty gives you specific legal rights, and you may alsohave other rights which vary from state to state and province toprovince. In addition, some states/provinces do not allowlimitations on how long an implied warranty lasts, and some donot allow the exclusion or limitation of incidental orconsequential damages. Accordingly, limitations as to thesematters contained herein may not apply to you.

●IN CANADA ONLY:This Warranty is not valid unless your Alpine car audio producthas been installed in your vehicle by an Authorized InstallationCenter, and this warranty stamped upon installation by theinstallation center.

●HOW TO CONTACT CUSTOMER SERVICE:Should the product require service, please call the followingnumber for your nearest Authorized Alpine Service Center.

Or visit our website at; http://www.alpine-usa.com

LIMITED WARRANTYALPINE ELECTRONICS OF AMERICA, INC. AND ALPINE OF CANADA INC. ("Alpine"), are dedicated to quality craftsmanship and arepleased to offer this Warranty. We suggest that you read it thoroughly. Should you have any questions, please contact your Dealeror contact Alpine at one of the telephone numbers listed below.

ALPINE ELECTRONICS OF AMERICA, INC.,19145 Gramercy Place, Torrance, California 90501, U.S.A.ALPINE ELECTRONICS OF CANADA, INC.,777 Supertest Road, Toronto, Ontario M3J 2M9, Canada Phone 1-416-736-6211Do not send products to these addresses.Call the toll free telephone number or visit the website to locate a service center.© 2006 NAVTEQ. All Rights Reserved.© 2006 Alpine Electronics of America, Inc. All Rights Reserved.

The WTR Logo is a trademark of theConsumer Electronics Association.

CAR AUDIO 1-800-ALPINE-1 (1-800-257-4631)NAVIGATION 1-888-NAV-HELP (1-888-628-4357)