REMINGTON PORTABLE TYPEWRITER - Xavier University · TYPEWRITER MODELS AN.QR and ER ( REVISED MAY, 1953 ) DIVISION Or SPERRY RAND CORPORATION 315 FOURTH AVENUE NEW YORK, N. Y. AP-92

PARTS CATALOG

FOR

REMINGTON PORTABLE

TYPEWRITER

MODELS AN.QR and ER

( REVISED MAY, 1953 )

DIVISION Or SPERRY RAND CORPORATION

315 FOURTH AVENUE

NEW YORK, N. Y.

AP-92 PRINTED IN U.S.A. 12 C

PARTS CATALOG

FOR

REMINGTON PORTABLE

TYPEWRITER

MODELS .AN.QR and ER

( REVISED MI, 1953 )

Maintenance Dept.

NEW YORK, N. Y.

REMINGTON PORTABLE TYPEWRITER

MODELS , AN, OR AND ER

FOREWORD

This catalog illustrates and lists mail order parts for the

Remington Portable Typewriter Models AN, OR and ER whichSUPERSEDES THE PARTS CATALOG ISSUED IN 1949.

A NUMERICAL PRICE LIST OF PARTS, PORM NO. PL-92 IS FURNISHEDAPART FROM THIS CATALOG WHICH CONTAINS PART NUMBERS AND LIST

PRICES OF PARTS APPEARING IN THIS CATALOG.

If, for any reason, a part required cannot be found in THISCATALOG OR IF DOUBT EXISTS AS TO THE CORRECT PART, PLEASEsend a sample PART OR A REASONABLE DRAWING OF THE PART ALONG

WITH YOUR ORDER WHENEVER POSSIBLE. In MANY CASES IT IS A

GREAT HELP TO THE FACTORY IF THE MACHINE SERIAL NUMBER IS

GIVEN.

The Company shall not be liable for any default of delay

CAUSED BY ANY CONTINGENCIES BEYOND ITS CONTROL PREVENTING

OR INTERFERING WITH DELIVERIES, INCLUDING WAR, RESTRAINTSAFFECTING SHIPPING, OR STRIKE, LOCKOUT, ACCIDENT, NON-ARRIVAL OR DELAY OF STEAMER OR CARRIER, OR REDUCED SUPPLYOF RAW MATERIAL OR EXCESSIVE COSTS THEREOF, OR ANY OTHERCONTINGENCIES BEYOND ITS CONTROL.

Printed in U.S.A. Issued, 1953


MODELS AN, QR AND ER

INDEX TO ILLUSTRATIONS

SUBJECT PAGE

ALIGNING SCALE 13

BACK SPACE MECHANISM 6BELL MECHANISM 12

CARRIAGE ASSEMBLY 13CARRIAGE COVERS (PANELS) 5CARRYING CASE 16

DRUG LABEL PLATEN . 17

ESCAPEMENT 9

FEED ROLLS 13FOOT EQUIPMENT . 6

KEY LEVERS 11

LINE SPACE MECHANISM 14

MACHINE COVERS (PANELS) 5MARGIN RELEASE MECHANISM 12

PAPER SCALE 13PAPER TABLE 5PAPER TROUGH . . * 13PLATEN 14

RIBBON COVER MECHANISM 11RIBBON DRIVE MECHANISM T 10

SHIFT MECHANISM 8SIDE PLATES 6SPACE BAR MECHANISM '. 7SPRING DRUM MECHANISM . 7

TABULATOR MECHANISM 15TYPE AND TYPE BARS 9TYPE BAR BELL CRANKS 11TYPE GUIDE 9

UNIVERSAL BAR 9

Printed in U.S.A. Issued, 1953

PAPER TABLE

PAPER SIC 3-IIB93-1169

10 CARRIAGE

10 SPACE 3-107512 SPACE 3-1076

SCREW 3-7018

SCREW 3-7022

SCREWS 3-7018

CARRIAGE REAR COVER

10" CARRIAGE WITH TAB. 3-1074

10" CARRIAGE WITHOUT TAB. 3-1086

CARRIAGE END COVER LEFT3-1176

WASHER 2-40904BE USED ON ll"CARR. ONLY

SCREW3-7018

CARRIAGE COVERS

CARRIAGE END COVER RIGHT3-1177

3-7023 ̂ "O SCREW 3-7059 UPPERLOWER " TOP COVER HINGE BRACKET 3-1164

' NRF PIN 3-1172

-TOP COVER

lO'CARR. WITHOUT TAB 3-1077lO'CARR WITH TAB QUIET RITER 3-I0B7

3-7023 § f SCREW 3-7059

I

SIDE COVER LEFT 3-1079

©- SCREW 3-7022

FRONT RAIL SCREW &REAR 3-7093

STOP RUBBERSPACE BAR

MACHINE COVERS

t "FRONT RAILSCREW.. i FRONT 3-7055

FRONT RAILWITH TAB. 3-1081WITHOUT TAB. 3-1082

LETTER SPACING RACK

lO" CARRIAGE

10 SPACE 3-4830

12 SPACE 3-4831BACK SPACE DOG SPRING 3-G039

ESCAPEMENT WHEEL

10 SPACE 3-4017

12 SPACE 3-4244

BACK SPACE DOG BELL

CRANK BRACKET ASSEM

3-4823

SCREW 3-7066BACK SPACE DOG AND BELL CRANK ASSEM

3-4824

KEEPER 3-7103

RIGHT SIDE PLATE 3-2082

VJ.

BACK SPACE KEY CAP42 KEY 2-5201844 KEY 2-52015

KEY LEVER COMB ASSEM.3-2084

FOOT PAD KEY3-2299-

LEFT SIDE PLATE

3-2081

BACK SPACE KEY LEVER42 KEY 3-240544 KEY 3-2428

SHIFT LOCK LATCH STRIKE

LEFT 3-2407RIGHT 3-2408RUBBER 3-4241

FOOT PAD3-2298

FOOT PAD CUP3-2297

FOOT PAD SCREW3-7072 O.S. ■

3-7093 N.S.

BACK SPACE MECHANISM

SPACE KEY ESCAPEMENT OPERATINGARM BRACKET ASSEM. 3-4826SCREW 3-7066

NUT 3-5005

WASHER 4-11769SPACE BAR SHAFTRETAINING RING

3-7103

0

ESCAPEMENT BODY ASSEMGOMP. 3-4009

\J.SPACE KEY ESCAPEMENT

OPERATING ARM SET

SCREW 3-7045 /NUT 3-5005 0

DRAW CORD 3-4107

3-4004 SPRING DRUM ASSEM. COMPLETE

3-4104 SPRING DRUM BODY

3-4105 SPRING DRUM CORE

3-4106 SPRING DRUM CAP

3-6041 'carriage TENSION SPRING

SCREW A3-7066—^

RATCHET PAWL

SPACE BAR SHAFT ASSEM3-209!SPRING DRUM SCREW 3-7032

SPACE BAR PULL WIRE ASSEM. 3-2083

SPACE BAR3-2415

SPACE BAR STOP RUBBER

3-1106SPACE BAR SHAFTSPRING 3-6062

SPRING DRUM TENSION

RATCHET 3-4113

SPACE BAR LEVERSPRING 3-6073

SPACE BAR MECHANISM SPACE BAR SCREWS (SELF TAPPING)-3-7061

EXPLODED VIEW OF INSET

SEGMENT PIVOT SCREW 3-7041NUT 3-5008

SHIFT KEY SHAFT RETAINER 3-7114 O.S.3-7103 N.S,

SHIFT LEVER KEYCAP 2-52016

00

TYPE BAR UNIVERSAL BAR SUPPORT

3-3046

SHIFT OPERATING ARM SHAFT SPRING 3-6017

SEGMENT 3-3185-^SEGMENT ROLLERRETAINER 2-40806-

TYPE GUIDE3-3104

SEGMENT SHIFT OPERATING ROLLER3-3171

SHIFT OPERATING SHAFT LOCKING PLATE 3-2118SCREWS 3-7066

SIDE PLATE SUPPORT ASSEM. COMP. 3-2085

SPACER 2-40978 OR 2-40936 ASNEEDED - SEGMENT OSCILLATORPIVOT SCREW 3-7026

NUT 3-5005

SHIFT LOCK KEYCAP 2-52015

SEGMENT SHIFT a RIBBONCONTROL SHAFT BRACKET3-2112

SCREW 3-7019

SHIFT LEVER ASSEMBLYCOMP. 3-2090

SEGMENT ROLLER GUIDE

BRACKET 3-2414, SCREW 3-7019

ECCENTRIC 3-2III,SCREW 3-7047

3-7019 ISEGMENT

OSCILLATOR3-2127

SHIFT LOCK LATCH STRIKERIGHT 3-2408

SHIFT LEVER SPRING 3-60 6

SHIFT LINK KEEPER

3-7119

SHIFT MECHANISMSHIFT LOCK LEVERSPRING 3-6015

SEGMENT SHIFT STOP SCREW FRONT 3-2008

NUT 3-5008, CUP 3-2391, RUBBER 3-2108

SEGMENT OPERATING SHAFT ASSEM. 3-2088

SCREW 3-7047 O.S.

3-7023 N.S.

SEGMENT SHIFT STOP SCREW REAR 3-2008

GRUBBER 3-4241

SHIFT LOCK LATCH STRIKE LEFT 3-2407

TTTTMrm

©o

\

vo

,3-3010

ESCAPEMENT BODY PIVOT SCREW 3-7077,NUT 3-5005

ESCAPEMENT BODY STOP

ADJUSTING SCREW 3-7045

SCREW 3-7047

ESCAPEMENT BODY TRIP

ADJUSTING SCREW 3-7045-

ESCAPEMENT BODY ASSEMBLY 3-4009 (WITH DOGS)

/SCAPEMENT STEPPING DOG 3-4119,SCREW 3-7044,NUT 3-5003

ESCAPEMENT FIXED DOG 3-4011 SCREW 3-7043,NUT 3-5003

ESCAPEMENT WHEEL & PINION

10 SPACE 3-401712 SPACE 3-4244

SCREW 3-7019 TYPE GUIDE 3-3104

SKETCH "A"

ESCAPEMENT BELL CRANK SCREW 3-7090NUT 3-5005

ESCAPEMENT BELL CRANKASSEM. 3-4008

0

0 0©

o

ESCAPEMENT BODY BRACKET COMPLETE3-4006 10 SPACE3-4087 12 SPACE

3-4007 BRACKET ONLY

ESCAPEMENT BODY BRACKET SCREW 3-7066

STEPPING DOG SPRING

3-6036

FIXED DOG SPRING3-6037

ESCAPEMENT WHEEL SHOULDERSCREW 3-7031

ESCAPEMENT BODY TENSIONSPRING 3-6038

ESCAPEMENT WHEEL SCREWNUT 3-5008

TYPE BAR UNIVERSALBAR ROCKER 3-3153

LETTER SPACING RACK—10 CARRIAGE10 SPACE 3-4830

12 SPACE 3-4831

TYPE GUIDE

3-3104

BACK SPACE DOG SPRING

3-6039

TYPE BAR UNIVERSALBAR 3-3154

SCREW 3-7070

BACK SPACE DOG 3-4824

TYPE BAR UNIVERSALBAR SUPPORT 3-3046

(FOR REPAIRMEN)3-3207 RIGHT3-3208 LEFT

TYPE BAR WITH TYPE 3-3092

TYPE ONLY 3-3163

•TYPE BAR LINK 3-1100

ESCAPEMENT BODY TRIP ADJUSTINGSCREW 3-7045, NUT 3-5005

TYPE BAR UNIVERSAL BAR ROCKER ,LOWER PIVOT SCREW 3-7077, NUT 3-5005 TYPE BAR FULCRUM

WIRE 3-6102

ESCAPEMENT a UNIVERSAL BAR

RIBBON SPOOL SHAFT TENSION COLLAR 3-5106

SCREW 3-7081 , SPRING 3-6034 RIBBON SPOOL SHAFT GUARD RIGHT 3-2028.SCREW 3-7023

RIBBON SPOOL SHAFT RIGHT 3-2026

RIBBON

RIBBON SPOOL SHAFT

LEFT 3-2074

RIBBON SPOOL RATCHET RIGHT

3-2029

RIBBON SPOOL PAWL■ SPRING 3-6025

-RIBBON SHIFT SUPPORT3-2021

mRIBBON CARRIER3-3010

SPOOLL GUARD ASSEMSCREW 3-7023

LEFT 203

RIBBON WINDINGDISC 02

i0

0 •

RIBBON UNIVERSAL

BAR RETAINER 3-71 13

KEY LEVER CAP 2-52015

\

„ IL-RIGHT SIDE FRAM, .A

LEFT SIDE FRAME

3-2081

RIBBON SPOOL SHAFT RATCHET

LEFT 3-2032

RIBBON UNIVERSAL BAR 3-2099

MANUAL RIBBON REVERSE DETENT SPRING 3-6051

RIBBON REVERSE ACTUATOR RETAINER 3-7101

RIBBON SHIFT SUPPORT BEARINGSCREW 3-7054, V/ASHER 3-5108 RIBBON DRIVE MECHANISM

manual'RIBBON REVERSE ARM 8 BRACKET3-2036, SCREW 2-40224FINGER PAD 3-8005

RIBBON CONTROL BELL CRANK LINK 3-2163

RIBBON CONTROL SHAFT LEVER SPACER 3-5102

RIBBON CARRIER DOWNSTOP 3-2167SCREW 3-7023,

RIBBON CONTROL SHAFT LEVER ASSEM. 3-2033

RIBBON CARRIER

3-3010

RIBBON ACTUATORARM HUB SET SCREW/

3-7081 /

KEY LEVER FULCRUM WIRE 3-6105

KEY LEVER 1ST. ROW 3-2173

2ND. ROW 3-2174

3RD. ROW 3-21754TH. ROW 3-2176

RIBBON CONTROL BELL CRANK 3-2162

RIBBON CONTROL SHAFT LEVER STOP ECCENTRIC 3-2161

SCREW 3-7022 O.S.3-7066 N.S.

RIBBON CONTROL LEVER LINK 3-2166

RIBBON CONTROL BELL CRANK RETAINER 3-7101

RIBBON CONTROL LEVER RETAINER 3-7113

RI^ON CONTROL LEVER STUD 3-9155

RIBBON CONTROL LEVER

BRACKET SCREW 3-7023

RIBBON CONTROL LEVERBRACKET 3-2165

FINGER PAD

3- 8005II

•<1 P

KEY LEVER COMB &UPSTOP ASSEM.3-2084

FINGER PAD3-8005

TOUCH CONTROLLEVER 3-2417

TOUCH CONTROL SPRING 3-6009RETAINER 3-6050

RIBBON UNIVERSAL BAR RETAINER 3-7113

RIBBON CONTROL LINK PIVOT SCREW STUD 3-9122

RIBBON CONTROL LEVER 3-2164

RIBBON CONTROL LINK ASSEM. 3-2034

RIBBON UNIVERSAL BAR3-2099

TYPE BAR BELL CRANK 3-2188 THRU 3-2227

BELL CRANK FULCRUM WIRE 3-6103

KEY LEVER SPRING 1ST,2ND,3RD ROW 2-519404TH ROW 3-6058

RIBBON COVER MECHANISM

ro I

SCREW 3-7077'NUT 3-5005

MARGIN RELEASE SHAFT

3-2050

MARGIN RELEASE BRACKET SUPPORTWITH TAB 3-2045WITHOUT TAB 3-2069SCREW 3-7019

MARGIN STOP RIGHT 3-4866

ARRIAGE END FRAME RIGHT

/NUT 3-5008

RETAINING RING 3-7113

BELL HAMMER SPRING 3-6032RETAINER 3-6050

MARGIN STOP RACK

IO"CARR. 10 SPACE 3-4341

LINE LOCK ACTUATING ARM

BELL HAMMER 3-2282MARGIN RELEASE BRACKET

3-1701 \

o

KEY CAP 2-52018

LINE LOCK SLIDE 3-3152 ISCREW 3-7013 SPRING 3-60^

NUT 3-5012

N.1

TYPE BAR UNIVERSAL BAR ROCKER3-3153, SPRING 3-6053 MARGIN RELEASE KEY LEVER

42 KEY 3.-2I7944 KEY 3-2178LINE LOCK LEVER 3-2392

RETAINER 2-50006 MARGIN RELEASE KEY LEVERSPRING 3-6003

MARGIN STOP LEFT 3-4865SPRING 3-6054

MARGIN RELEASE CONNECTING LINK 3-6III

SCREW ON CLIP 3-7105, RETAINER 3-7101

MARGIN RELEASE MECHANISMMARGIN RELEASE KEYLEVER DOWNSTOP RUBBER 3-4241

FEED ROLL RELEASE LEVER 3-4843FINGER PAD 3-8006, RETAINER 3-7101,SILENCER SPRING 3-6081

CARR. LOCK LEVERSTOP NUT 3-4291CARR. LOCK SPRING

3-4290

PAPER

10 "CARR.TROUGH

3-4846

CARR. LOCK LEVER^ 10" CARR, 3-4288

SCREW 3-7083 O.S.

CARRIAGE

RELEASE LEVER

FINGER PAD 3-8006'SPRING LEFT 3-6072PIVOT SCREW 4-11800

CARRIAGE RAIL FRONT 0 REAREND SCREW 3-7080,WASHER 3-5127

SCREW 3-7073 O.S.2-55465 N.S.

WASHER 3-5119

PAPER SCALE PIVOT BRACKETRIGHT 3-4168, SCREW 3-7022,PIVOT SCREW 3-7094,NUT 3-5003

PAPER SCALE SPRING ANCHOR

4-11745

FEED ROLL SUPPORT ARM RIGHT 3-4025SET SCREW 3-7086

CO

MARGIN STOP RACK NUT

OUTER 3-5008, INNER 3-5012

PAPER BAIL ARM ASSEM.

IO"CARR. 3-4850RETAINER 3-7113^ SPRING 3-6071 O.S.^ 3-6080 N.S.

CARRIAGE FRAME■ IO"CARR. 3-4839 /

MARGIN STOP RIGHT

3-4866_ 1

■'MARGIN STOP RACK.,J0 SPACE 3-4341 ^

MARGIN STOP LEFT3-4865, SPRING3-6054

CARRIAGE ROLL RETAINER3-4267

SPRING 3-6080

m- CARR AGE RAIL FRONT 3-4 02

FEED ROLL RELEASE SHAFT 3-4306

FEED ROLL SUPPORT ARM LEFT 3-4023TENSION SPRING lO' CARR. 3-6007

1 1 "CARR. 3-6079LINE SPACE STOP

o-»

FEED ROLL REAR 3-4819

PAPER SCALE PIVOT BRACKETLEFT 3-4295 ^PIVOT,LEFT 3-4296

ALIGNING SCALE10 SPACE 3-433112 SPACE 3-4332SCREW 3-7022

PAPER SCALE10" CARR. 10 SPACE

3-4286

LINE SPACE DETENTRELEASE LEVER 3-430!FINGER PAD 3-8005PIVOT STUD 3-9009

CARRIAGE RAIL REAR3-4100

PAPER BAIL ROLL ROD10 CARR. 3-4313

PAPER BAIL ROLL 3-4043

PAPER SCALE SPRING 3-6019

FEED ROLL ROCKER ARMRIGHT 3-4800

CARRIAGE a SIDE PLATESCREW 3-7019DOWEL PINS 3-9001

CARRIAGE RAIL FRONT 8 REAREND SCREW NUT 3-5010SCREW 3-7080WASHER 3-5127

FEED ROLL FRONT 3-4355

FEED ROLL ROCKERARM LEFT 3-4022 CARRIAGE

LINE SPACE RATCHET DETENT

ROLL ARM "3-4860ECCENTRIC NUT 3-5009

LINE SPACE PAWL CARRIER 3-4844

SPRING 3-6077

PLATEN SPACER LEFT3-5136

LINE SPACE LEVER 3-4842SCREW 3-7034

NUT 3-5008

CARRIAGE FRAME

10" CARR. 3-4839

LINE SPACE RATCHET DETENTRELEASE LEVER 3-4302FINGER PAD 3-8005

PLATEN RATCHET 3-4852

STUD 3-9009

CARRIAGE RELEASE LEVERSPRING 3-6072

PLATEN KNOB,LEFTCOMP. 3-4829

PLATEN SPACER,RIGHT.062 3-5137.020 3-5138

PLATEN HEAD RIGHT SET SCREW3-7076

PLATEN WITHOUT VARIABLE CLUTCH

IO"CARR. 3-4856

PLATEN WITH VARIABLE CLUTCH

10" CARR. 3-4858

PLATEN KNOB, RIGHT 3-4828SCREW 3-7076

53

LINE SPACE REGULATOR 3-4841

^5LINE SPACE STOP 3-4169

\PAPER SCALE PIVOT BRKT., LEFT 3-4295PIVOT. LEFT 3-4296

LINE SPACE REGULATOR

DETENT 3-4845

SCREW 3-7095

PLATEN CLUTCH CONERETAINING SPRING 3-6074

PLATEN CLUTCH

CONE 3-4327

LINE SPACE RATCHET DETENT ROLLARM ECCENTRIC SCREW 2-40004

SPRING 3-6076

PLATEN CLUTCH JAWS

PLATEN CLUTCH DOG

4326

\ RETAINING SPR.PLATEN RATCHET SPACING COLLAR.072 3-5139.078 3-5140 ^

3-6075

PLATEN RATCHET SPACINGSHIM .010 3-5141 ^

PLATEN RATCHET

RETAINING RING3-7122

PLATEN SHAFT, RIGHT10" CARR. 3-4324

PLATEN a LINE SPACE MECHANISM

TAB. RACK COMPLETE WITH STOPS 10 CARR

10 SPACE 3-409612 SPACE 3-4097 TAB. RACK ADJUSTING SCREW 3-7078

NUT 3-5005TAB. STOP SPRING COMB 10 CARR

10 SPACE 3-4145

12 SPACE 3-4228

TAB STOP 4144

TAB. SET FINGER ASSEM.3-2044

TAB. STOP RACK

10 SPA 10 SPACE 3-409812 SPA 12 SPACE 3-4099

LOCK WASHER 3-5129

SCREW 3-7085

MARGIN BRACKET SUPPORT 3-2045

TAB. BLADE OPERATING LEVERTAB. CLEAR FINGER-.>\ASSEM-iS-EOi^S-""

TAB. STOP FULCRUM WIRE

10" CARR. 3-6113KEEPER 3-7l2h-_ TAB. LETTER SPACING RACK RELEASE LEVER 3-4101

SCREW 3-7062,NUT 3-5003ORSION ISPRING3-6004 ^

TAB. LETTER SPACING RACK RELEASE LEVERLINK 3-1101, RETAINER 3-7101, NUT 3-5005SHOULDER NUT 3-5001

TAB. STOP BLADE3 2281TAB. SET a CLEAR SHAFT

ASSEM. 3-2080

SPRING3-6049

& ^ RETAINER

3-6050TAB. SET AND CLEAR Sl^FTACTUATOR KEY 3-2403/SCREW 3-7086 '

' CARR.-LOWER RAIL

/ REAR 3-4100 ^

SIDE PLATE RIGHT3-2082

iiVr'r' KEY CAP 2-52015TAB. BELL CRANK 3-2296

RETAINER 3-7103

TAB. KEY LEVER CONNECTING

LINK 3-2267

RETAINERESCAPEMENT WHEEL a PINION

10 SPACE 3-4017 12 SPACE 3-42442-50004

CARRIAGE LOWER RAIL FRONT3-4102

VJ 3-7023

0 TAB. KEY LEVER3-2040

TAB. KEY LEVER SPRING2-5IS40

0 TAB. SET a CLEAR KEY LEVER

TAB. STOP SET a CLEAR LINKASSEMBLY 3-1700

SIDE PLATE LEFT3-2081

RETAINER 3-7103

TABULATOR MECHANISMKEY LEVER COMB a UPSTOP 3-2084SCREW 3-7023

HANDLE 3-9931

RIVET 3-9239(2 )

BRAIXET 3-9901 (2)

RIVET 3-9242(4)

WASHER 3-5120(4)

CARRYING CASE ASSEM.COMPLETE

lO'CARR. 3-9859iT'cARR. 3-9856

1^1

LOCK 3-9960

RIVET 3-9254 (2)

WASHER 3-5126(2); -nV.v:

* . . .

/• '"i . I ' •• •

HINGE UPPER 3-9958 (2)

HINGE LOWER 3-9957(2)RIVET UPPER 3-9240 (4)

' «« i • I r.

I-.' ^ . .. . ̂ 1/ A , .

V."" • *. MACHINE LOCK RIGHTRIVET LOWER 3-9242 (4)vs

i "

ci -^5 • '. • . . . -

Ns:»,

'.f.9

MACHINE LOCK LEFT

''C>

CARRYING CASE

MACHINE LOCK 3.9980 (2)

RIVET 3-9242 (4)

BRACKET 3-9945

RIVET 3-9242LATCH 3-9947

SPRING 3-6067

PIN 3-9(94, KEEPER 3-7101

BRACKET 3-9944

RIVET 3-9242 (3)

LATCH 3-9946

SPRING 3-6066

PIN 3-9194

KEEPER 3 -7101

RIVET 3-9243(2)

WASHER 3-5126(2)

3-9961

FOOT 3-9968(4)

.GRIP WIRE ROD ASSEMBLED

10" CARR. 3-4878n" CARR. 3-4879

GRIP WIRE RELEASE LEVERBRACKET ASSEMBLED 3-4259

SCREWS 3-7047 (2)

SPRING 3-6065

PLATEN HEAD RIGHT3-4330

PLATEN

10" CARR. 3-4874I I" CARR. 3-4875

SCREWS 2-46432 (3)

DRUG LABEL PLATEN

PLATEN COMPLETE lO" CARR. 3-4872PLATEN COMPLETE l l" CARR. 3-4873


MODELS AN, OR AND ER

PART NO, DESCRIPTION CABINET LOCATION

3-1012 Paper Table Assem. with Paper Side Guide - 12 Space Tab. Mach, (0,S. Sup. by 3-1076 & 3-1085)3-1050 Space Bar Pull Wire Assembled (O.S. - Sup. by 3-2083)3-1052 Top Cover Hinge Bracket Assembled, Left (O.S. - Sup. by 3-1164)3-1053 . Top Cover Hinge Bracket Assembled, Right (O.S. - Sup. by 3-1164)3-1056 Paper Table Assem. with Paper Side Guide - 10 Space Tab. Mach. (O.S; Sup. by 3-1075 & 3-1084)

3-1.059 Front Rail Assembled - Machine with Tabulator (O.S. - Sup. by 3-1081)3-1060 Top Cover Assembled - Machine without Tabulator (O.S. - Sup. by 3-1077)3-1070 Front Rail Assembled - Machine without Tabulator (O.S. - Sup. by 3-1082)3-1071 ■ Top Cover Assembled - Machine with Tabulator (O.S. - Sup. by 3-1087 & 3-1088)3-1072 Front Cover Assembled - For France and French Colonies (O.S. - Sup. by 3-1180)

3-1073' Rear Cover Assembled

3-1074 Carriage Rear Cover Assembled - 10" Carriage - Machine with Tabulator

3-107.5, . Paper.Table Assembled - 10" Carriage - 10 Space3-1076 Paper Table Assembled - 10" Carriage - 12 Space

3-1077 Top Cover Assembled - IC'-Carriage - Machine without Tabulator

3-1079 .. Side Cover, Left, Assembled3-1030 .. . Side Cover, Right, Assembled3-1031 Front Rail Assembled - Machine with Tabulator

3-1032 Front Rail Assembled - Machine without Tabulator

3-1033 Carriage Rear Cover Assembled - 11" Carriage - Machine with Tabulator

3-1084 Paper Table Assembled - 11 "- Carri age - 10 Space

3-1085 Paper Table Assembled - 11" Carriage>- 12 Space.

3-1086 Carriage Rear Cover Assembled - .10" Carriage - Machine without Tabulator

3-1087 Top Cover Assembled (Quiet-Riter) 10" Carriage - Machine with Tabulator3-1088 Top Cover Assembled (OffiCe-Riter) 11" Carriage - Machine'with Tabulator

3-1100 Type Bar Link

3-1101 Tabulator Letter Spacing Rack Release Link

3-1102 ■ Ribbon Winding Disc

3-1103 Side Cover, Right, Assembled (O.S. - Sup. by 3-1080)3-1104 Side Cover, Left, Assembled (O.S. - Sup. by 3-1079)

3-1106 Space Bar Stop

3-1107 Rear Cover Assembled (O.S. - Sup. by 3-1073)3-1108 Front Cover Assembled (O.S. - Sup. by 3-1175)3-1115 Carriage Rear Cover Assembled (O.S. - Sup. by 3-1074, 3-1083 cSc 3-1086)3-1120 Paper Side Guide (O.S. -Sup. by 3-1169)

3-1121 Carriage End Cover, Right (O.S. - Sup. by 3-1177)3-1122 Carriage End Cover, Left (O.S. -Sup. by 3-1176)3-1137 Top Cover Name Plate

3-1138 Carriage End Cover, Left - 56 Tooth (Special Equipment) (O.S..- Sup. by 3-1181)3-1164' Top Cover Hinge Bracket

3-1169 Paper Side Guide

3-1172 Top Cover Hinge Pin

3-1175 Front Cover Assembled

3-1176 Carriage' End Cover, Left3-1177 ' Carriage End Cover, Right

3-1180 ' Front Cover Assembled - For France and French Colonies

3-1181 Carriage End Cover, Left - 56 Tooth (Special Equipment)3-1700 Tabulator Stop Set and Clear Link Assembled

3-1701 Margin Release Bracket Assembled

3-1702 Margin Release Bracket Support Assembled, Complete - Machine with Tabulator

3-1703 ■ Margin Release Bracket Support Assembled, Complete - Machine without Tabulator

3-2001 Side Plate Support Assembled (O.S. - Sup. by 3-2085)3r2004 " Side Plate Assembled, Right (O.S. - Sup. by 3-2082)3-2006 ■ Side Plate Assembled, Left (O.S. - Sup. by 3-2081)3-2007 ■ Segment Shift Stop Bracket Assembled, Left (O.S.)

Printed in'U.S.A. - Produced by Flexoprint Panel 19 Issued, 1953



PART NO. DESCRIPTION CABINET LOCATION

3-2008 Segment Shift Stop Screw Assembled, Lower "3-2009 Segment Shift Stop Bracket Assembled, Right (O.S.)3-2010 Shift Operating Arm Shaft Assembled (O.S. - Sup. by 3-2077) ;3-2015 Shift Lever Assembled, Complete .(O.S. - Sup. by 3-2090)3-2020 Touch Control Lever Assembled (O.S. -,Sup. by 3-2417) ,

3-2021 Ribbon Shift Support Assembled, Complete

3-2025 Ribbon Spool Assembled, Complete, Right3-2026 Ribbon Spool Shaft Assembled, Complete, Right '3-2028 Ribbon Spool Guard Assembled, Right :3-2029 Ribbon Spool Ratchet Assembled, Right ■

3-2030 Ribbon Spool Assembled, Complete, Left3-2031 Ribbon Spool Guard Assembled, Left3-2032 Ribbon Spool Ratchet Assembled, Left3-2033 Ribbon Control Shaft Lever Assembled3-2034 Ribbon Control Link Assembled

3-2035 Ribbon Control Lever Assembled3-2036 Manual Ribbon Reverse Arm and Bracket Assembled3-2038 Key Lever Comb and Up Stop Assembled (O.S. - Sup. by 3-2084)

3-2040 Tabulator Key Lever Assembled3-2041 Space Bar Shaft Assembled (O.S. - Sup. by 3-2091) '

3-2042 Margin Release Bracket Support Assem., Complete - Machine with Tab. (O.S. - Sup. by 3-1702)3-2043 Tabulator Clear Finger Assembled ^

3-2044 Tabulator Stop Set Finger Assembled

3-2045 Margin Release Bracket Support Assembled - Machine with Tabulator - 10 and 12 Space

3-2048 Margin Release Bracket Assembled (O.S. - Sup. by 3-1701)

3-2050 Margin Release Shaft Assembled .

3.7-2051 Tabulator Set and Clear Shaft Assembled (O.S. - Sup. by 3-2080)3-2052 Tabulator Stop Set and Clear Link (O.S. - Sup. by 3-1700)3-2058 Margin Release Bracket Support Assem., Complete - Machine without Tab. (0. S. Sup. by 3-2069)3-2069 Margin Release Support Assembled - Machine without Tabulator "

3-2074 Ribbon Spool Shaft Assembled, Complete, Left3-2076 Segment Shift Stop Screw Assembled (O.S. - Sup. by 3-7089)3-2077 Shift Operating Shaft Assembled, Complete (O.S. - Sup. by 3-2088)3-20B0 Tabulator Stop Set and Clear Shaft Assembled3-2081 Side Plate Assembled, Left

3-2082 Side Plate Assembled, Right3-2033 Space Bar Pull IVire Assembled

3-2094 Key Lever Comb and Up Stop Assembled

3-2085 Side Plate Support Assembled

3-2088 Shift Operating Shaft Assembled, Complete

3-2090 Shift Lever Assembled, Complete3-2091 Space Bar Shaft Assembled

3-2099 Ribbon Universal Bar Complete

3-2107 Segment Shift Stop Bracket, Left (O.S.)3-2108 Ribbon Control Lever Stop (O.S.)

3-2108 Segment Shift Stop

3-2109 Segment Shift Stop Bracket, Right (O.S.)3-2110 Segment Roller Guide Bracket (O.S. - Sup. by 3-2414)

3-2111 Segment Guide Eccentric

3-2112 Segment Shift and Ribbon Control Shaft Bracket

3-2118 Shift Operating Shaft Locking Plate

3-2125 Shift Lock Latch Strike, Left (O.S. - Sup. by 3-2407)3-2126 Shift Lock Latch Strike, Right (O.S. - Sup. by 3-2408)3-2127 Segment Oscillator

3-2161 Line Lock Actuator Stop Eccentric (O.S.)

Issued, 1953 20 Produced by Flexoprint Panel

PART NO.

REMINGTON PORTABLE TYPEVWITER

MODELS' AN, OR AND. ER

DESCRIPTION CABINET LOCATION

3-2161 Ribbon Control Shaft Lever Stop

3-2162 Ribbon Control Bell Crank

3-2163 Ribbon Control Bell Crank Link3-2164 Ribbon Control Lever

3-2165 Ribbon Control Lever Bracket

3-2166

3-2167

3-2173

3-2174

3-2175

3-2176

3-2177

3-2178

3-2179

3-2180

3-2182

3-2182

3-2183

3-2185

3-2188

3-2189

3-2190

3-2191

3-2192

3-2193

3-2194

3-2195

3-2196

3-2197

3-2198

3-2199

3-2200

3-2201 .

3-2202

3-2203

3-2204

3-2205

3-2206

3-2207

3-2208 .

3-2209

3-2210

3-2211

3-2212

3-2213

3-2214

3-2215

3-2216

.3-2217

3-2218

,3-2219

3-2220

3-2221

3-2222

3-2223

Ribbon Control Lever Link

Ribbon Carrier Down Stop

Key Lever, First RowKey Lever, Second RowKey Lever, Third Row

Key Lever, Fourth RowKey Lever #0 - 44 Key MachineMargin Release Key Lever - 44 Key Machine

Margin Release Key Lever - 42 Key Machine

Back Space Key Lever - 44 Key-Machine (O.S. Sup. by 3-2428)

Key Lever Key Cap (Specify Character) (O.S. - Sup. by 2-51957)

Shift Lock Key Cap - Gray (O.S. - Sup. by 2-51957)Shift Key Cap - Gray (O.S. - Sup. by 3-2394)Bell Crank.Bracket

Type Bar Bell Crank # 1

Type Bar Bell Crank # 2Type Bar Bell Crank # 3Type Bar Bell Crank # 4Type Bar Bell Crank # 5Type Bar Bell Crank # 6

Type Bar Bell Crank # 7

Type Bar Bell Crank # 8Type Bar Bell Crank # 9Type Bar Bell Crank #10Type Bar Bell Crank #11

Type Bar Bell Crank #12Type,Bar Bell Crank #13Type,Bar Bell Crank #14

, Type,Bar Bell Crank #15Type Bar Bell Crank #16

Type Bar Bell Crank #26Type Bar Bell Crank #18Type Bar Bell Crank #19Type Bar Bell Crank, #20-Type Bar Bell Crank #21

Type Bar Bell Crank #22Type Bar Bell Crank.#24Type Bar Bell Crank #25Type.Bar Bell Crank #27Type Bar Bell Crank #28

, Type Bar Bell Crank #29, Type Bar Bell Crank #30Type Bar Bell Crank #31Type.Bar Bell Crank #32Type, .Bar Bell Crank #33

Type Bar Bell Crank-#34

Type Bar Bell Crank #35Type Bar Bell Crank #36Type Bar Bell Crank #37Type .Bar Bell Crank #38

■Printed in'U.S'.'A. - -Produced by Flexoprint Panel 21 Issued, 1953



PART NO.

3-2224 Type Bar Bell Crank #393-2225 Type Bar Bell Crank #403-2226 Type Bar Bell Crank #413-2227 Type Bar Bell Crank #423-2267 Tabulator Key Lever Connecting Wire

3-2268 Line Look Lever (O.S, - Sup. by 3-2392)3-2269 Back Space Key Lever Bell Crank (O.S.)3-2274 Space Bar (O.S. - Sup. by 3-2395)3-2282 Bell Hammer - 10 and 12 Space

3-2296 Tabulator Bell Crank

3-2297 Foot Pad Cup

3-2298 Foot Pad

3-2299 Foot Pad Key

3-2301 Back Space Key Lever Link (O.S.)3-2305 Type Bar Bell Crank #23

3-2306 Type Bar Bell Crank # 0 and #43

3-2307 Type Bar Bell Crank #173-2329 Key Lever Link # 0 and #433-2330 Key Lever Link #423-2331 Key Lever Link # 1

3-2332 Key Lever Link # 23-2333 Key Lever Link #413-2334 Key Lever Link #403-2335 Key Lever Link # 33-2336 Key Lever Link # 4

3-2337 Key Lever Link #393-2338 Key Lever Link #383-2339 Key Lever Link # 53-2340 Key Lever Link # 6

3-2341 Key Lever Link #37

3-2342 Key Lever Link #363-2343 Key Lever Link # 73-2344 Key Lever Link # 83-2345 Key Lever Link #353-2346 Key Lever Link #34

3-2347 Key Lever Link # 9

3-2348 Key Lever Link #103-2349 Key Lever Link #323-2350 Key Lever Link #333-2351 Key Lever Link #11 and #12

3-2352 Key Lever Link #30 and #313-2353 Key Lever Link #143-2354 Key Lever Link #133-2355 Key Lever Link #293-2356 Key Lever Link #16

3-2357 Key Lever Link #153-2358 Key Lever Link #183-2359 Key Lever Link #273-2360 Key Lever Link #173-2361 Key Lever Link #22

3-2362 Key Lever Link #253-2363 Key Lever Link #193-2364 Key Lever Link #213-2365 Key Lever Link #233-2366 Key Lever Link #26



REMINGTON PORTABLE TYPB'JRITER



3-2367 Key Lever Link #283-2368 Key Lever Link #203-2369 Key Lever Link #243-2379 Back Space Key Lever - 42 Key Machine (O.S. - Sup. by 3-2405)3-2382 Molded Key Cap (Small Size) For Special Characters (O.S. - Sup. by 2-51967)

3-2390 Shift Lock Latch Strike Nut Plate (O.S.)

3-2391 Segment Shift Stop Our

3-2392 Line Lock Lever

3-2393 . Tabulator Key Cap (O.S. - Sup. by 2-51957)3-2394 Shift Lever Key Cap (O.S. - Sup. by 2-51958)

3-2395 Space Bar (O.S. - Sup. by 3-2415)3-2397 Molded Key Cap (Small Size) For Special Characters (O.S. - Sup. by 2-51967)3-2403 Tabulator Stop Set and Clear Shaft Actuator Key

3-2405 Back Space Key Lever - 42 Key Machine

3-2407 Shift Lock Latch Strike, Left

3-2408 Shift Lock Latch Strike, Right3-2414 Segment Roller Guide Bracket

3-2415 Space Bar

3-2417 Touch Control Lever

3-2426 Ribbon Spool Tension Washer (Felt) (O.S.)

3-2428 Back Space Key Lever - 44 Key Machine

3-2430 Line Lock -Actuator

3-3003 Type Bar Anvil Assembled, Rubber Anvil - Machine with Tabulator (O.S.)3-3004 Type Bar Assembled (O.S. - Sup. by 3-3092)3-3005 Segment Bracket Assembled, Complete

3-3006 Universal Bar Support Assembled (O.S. - Sup. by 3-3046)3-3008 Type Bar Cushion Wire Assembled3-3010 Ribbon Carrier Assembled, Complete3-3014 Segment Assembled - U - 44 Key Machine (O.S. - Sup. by 3-3048)3-3028 Segment £: Bushing Assembled - U1 - 44 Key Machine,-Slot 7#43 Non-Radial (Special Equipment)

3-3029 Segment & Bushing Assem. - U2 - 42 & 44 Key Mach., Slots #42 &#43 Non-Radial (Spec. Equip.)3-3030 Segment & Bushing Assem.-U4- 42 £: 44 Key Mach., Slots #40 thru #43 Non-Radial (Spec. Equip.) ,3-3031 Segment & Bushing Assem.-U5- 42 & 4A Key Mach;, Slots #39 thru #43 Non-Radial (Spec. Equip.) ,3-3032 Segment Assembled -.U1 - 44 Key Machine, Slot #43 Non-Radial (Special Equipment)3-3033 Segment Assembled - U2 - 44 Key Machine, Slots #42 and #43 Non-Radial (Special Equipment)

3-3034 Segment Assembled - U4 - 44 Key Machine, Slots #40 thru #43 Non-Radial (Special Equipment)3-3035 Segment Assembled - U5 - 44 Key Machine, Slots #39 thru #43 Non-Radial (Special Equipment)3-3037 Segment Assembled - U2 - 42 Key Machine, Slot 7#42 Non-Radial (Special Equipment)3-3038 Segment Assembled - U4 - 42 Key Machine, Slots #40 thru #42 Non-RadiaL (Special Equipment)3-3039 Segment Assembled - U5 - 42 Key Machine, Slots #39 thru #42 Non-Radial (Special Equipment)

3-3040 . Segment Assembled - U3 - 42 Key Machine, Slots #41 and #42 Non-Radial (Special Equipment)3-3046 Type Bar Universal Bar Support Assembled

3-3047 Segment Assembled - U - 42 Key Machine

3-3048 Segment Assembled - U - 44 Key Machine

3-3049 Segment Assembled - 15 - 42 Key Machine, Slots #38 thru #42 Non-Radial (Special Equipment)

3-3050 Segment Assembled - U3 - 44 Key Machine, Slots_#41 thru #43 Non-Radial (Special Equipment)3-3052 Segment & Bushing Assembled - U - 42 and 44 Key Machines

3-3053 Segment cS: Bushing Assem. -15-42 Key Mach., Slots #38 thru #42 Non-Radial (Spec. Equip.)3-3054 Segment & Bushing Assem.-U3- 42 & 44 Key Mach., Slots #41 thru #4.3 Non-Radial (Spec. Equip.)3-3060 Segment & Bushing Assem. - U - 42 and 44 Key Machines with Tabulator (Rubber Anvil) (O.S.)

3-3073 Segment Assembled - U - 44 Key Machine with Tabulator (Rubber Anvil) (O.S.)3-3074 Segment Assembled - U - 42 Key Machine with Tabulator (Rubber Anvil (O.S.)

3-3092 Type Bar Assembled - Specify Space3-3093 Type Bar, Dead Key, Offset, Assembled with Type - 10 Space (Special Equipment)3-3094 - Type.Bar, Dead Key, Offset, Assembled with Type - 12 Space (Special Equipment)3-3104 Type Bar Guide

Printed in U.S.A. - Produced by Flexoprint Panel 23 Issued, 1953

PART NO.




3-3152 Line Look Slide

3-3153 Type Bar Universal Bar Rocker

3-3154 ■ ■ Type Bar Universal Bar

3-3156 Type Bar Cushion Bracket, Right3-3157 Type Bar Cushion Bracket, Left

3-3158 . Type Bar Cushion

3-3163 . Type (Specify Space)3-3171 Segment Guide Roller

3-3171 Segment Shift Operating Roller

3-3175 . Type Bar, Dead Key, Offset - 10 Space (Special Equipment) (O.S. - Sup. by 3-3210)

3-3176 Type Bar, Dead Key, Offset - 12 Space (Special Equipment) (O.S. - Sup. by 3-3211)3-3185 Segment - U - 42 and 44 Key Machines

3-3207 Type Bar, Right - For Repairmen3-3208 Type Bar, Left - For Repairmen3-3210' Type Bar, Dead Key, Offset - 10 Space (Special Equipment)

3-3211 Type Bar, Dead Key, Offset - 12 Space (Special Equipment)3-3212 Type Bar, Dead Key, Offset - 10 Space - Siamese (Special Equipment)3-3213 Type Bar, Dead Key, Offset - 12 Space - Siamese (Special Equipment)3-4000 Carriage Assembled - Machine with Tabulator - 10 Space (O.S.)3-4003 Spring Drum Assembled, Complete (O.S. - Sup. by 3-4004)

3-4004 Spring Drum Assembled

3-4005 Space Key Trip Shaft Bracket Assembled (O.S. - Sup. by 3-4826)3-4006 Escapement Body Bracket Assembled, Complete - 10 Space3-4007 Escapement Body Bracket Assembled

3-4008 Escapement Body Bell Crank Assembled

3-4009 Escapement Body Assembled, Complete3-4010 Escapement Body Assembled

3-4011 Escapement Fixed Dog Assembled

3-4012 Back Space Dog Bell Crank Bracket Assembled (O.S. - Sup. by 3-4823)3-4013 Back Space Dog Linkage Assembled (O.S. - Sup. by 3-4824)

3-4014 Back Space Dog Connecting Wire Assembled (O.S.)3-4017 Escapement Wheel Assembled - 10 Space

3-4021 Feed Roll Release Shaft Assembled (O.S. - Sup. by 3-4269)

3-4022 Feed Roll Rocker Arm Assembled, Left3--4023 Feed Roll Support Arm Assembled, Left

3-4025 Feed Roll Support Arm Assembled, Right3-4027 Feed Roll Assembled (O.S. - Sup. by 3-4819)3-4028 Feed Roll Release Lever Assembled, Complete (O.S.)3-4029 Feed Roll Release Lever Assembled (O.S. - Sup. by 3-4843)3-4038 Paper Bail Assembled, Complete (O.S.)

3-4039 Paper Bail Assembled (O.S. - Sup. by 3-4850 & 3-4851)3-4043 Paper Bail Roll Assembled

3-4044 Paper Scale Pivot Bracket Assembled, Right (O.S. - Sup. by 3-4168)3-4046 Carriage Release Levers & Letter Spacing Rack Assem., Comp. - 10 Space (O.S.)

3-4048 Line Space Ratchet Detent Roll Arm Release Lever Assembled (O.S.)3-4049 Line Space Ratchet Detent Roll Arm Assembled (O.S. - Sup. by 3-4860)3-4050 Line Space Regulator Assembled, Complete (O.S.)3-4051 Line Space Regulator Assembled (O.S. - Sup. by 3-4841)3-4052 Line Space Pawl Carrier Assembled, Complete (O.S. - Sup. by 3-4844)

3-4054 Line Space Ratchet and Clutch Ring Assembled (O.S. - Sup. by 3-4852)3-4055 Line Space Lever Assembled (O.S. - Sup. by 3-4842)3-4056 Platen Assembled (O.S. - Sup. by 3-4856 & 3-4857)3-4057 Clutch Gear Assembled (O.S. r- Sup. by 3-4326 & 3-4327)3-4060 Platen Knob, Right, Gray (O.S. - Sup. by 3-4805)

Issued, 1953 24' Produced by Flexoprint Panel

PART NO.


MODELS AN, OR AND.ER


3-4062 Paper Trough Assembled (O.S. - Sup. by 3-4846 & ,3-4847)3-4065 Platen Knob Assembled, Complete, Left (O.S. - Sup. by 3-4807)3-4067 Platen Assembled, Complete (O.S. - Sup. by 3-4858 & 3-4859)3-4071. Margin Stop Assembled, Left (O.S..- Sup.'by 3-4865)3r4072 Margin Stop Assembled, Right (O.S. - Sup. by 3-4866) ■

3-4.076 . Carriage Frame Assembled, Complete - Machine .without Tabulator - 10.Space (O.S.)3-4077 Carriage Assembled - Machine without Tabulator -.10 Space (0.3.)

3-4085 Carriage Assembled - Machine without Tabulator --12 Space (O.S.)3-4087 Escapement Body Bracket Assembled, Complete - 12.Space3-4088. . Carriage Frame Assembled, Complete - Machine with Tabulator - 12 Space (O.S.) .

3-4091. Carriage Release Levers & Letter Spacing Rack Assem., Comp. - 12 Space (O.S.)3-4092 Carriage Assembled - Machine without Tabulator -. 12 Space (O.S.) ■

3-4094 Carriage Frame Assembled, Complete - Machine without Tabulator - 12 Space (O.S.)3-4096 Tabulator Stop Rack Complete - 10 Space

3-4097 Tabulator Stop Rack Complete - 12 Space

3-4098 Tabulator Stop Rack Assembled - 10 Space

3-4099 Tabulator Stop Rack Assembled - 12 Space

.3-4100 Carriage Rail Assembled, Rear3-4101 Tabulator Letter Spacing Rack Release Lever Assembled

3-4102 Carriage Rail Front

3-4104 Spring Drum Body

3-4105 Spring Drum Core

3-4106 Spring Drum Cap

3-4107 Spring Drum Draw Cord

3-4113 Spring Drum Tension Ratchet

3-4119 Escapement Stepping Dog3-4125 Carriage Stop (O.S. - Sup. by 3-4280)3-4132 Feed Roll Release Shaft Collar (O.S.)

3-41.33 Feed Roll Support Arm Stop (O.S.)

3-4144 Tabulator Stop

3-4145 Tabulator Stop Spring Comb - 10 Space

3-4146 Tabulator Stop Spring Comb Support

3-4147 Margin Stop Rack - 10 Space (O.S. - Sup. by 3-4341 & 3-4342)3-4165 Paper Bail Roll Rod (O.S. - Sup. by 3-4313 & 3-4314)

3-4166

3-4167

3-4168

3-4168

3-4169

Paper Scale Pivot Bracket, Right (O.S., - Sup. by 3-4168)Paper Scale - 10 Space (O.S. - Sup. by 3-4286)Paper Scale Pivot Bracket, Left (O.S. - Sup. by 3-4295)Paper Scale Pivot Bracket, RightLine Space Stop

3-4170 Paper Scale Pivot, Left (O.S. - Sup. by 3-4296)3-4174 .Letter Spacing Rack Nut Plate (O.S.)3-4175 Line Space Ratchet Detent Roll Arm Release Lever (O.S. - Sup. by 3-4302)

3-4181 " Line Space Link (O.S.)3-4190 ' Platen Shaft (O.S. - Sup. by 3-4324 & 3-4325) ,

3-4195 Aligning Scale Bracket (O.S. - Sup. by 3-4331 & 3-4332)3-4195 Aligning Scale Bracket (Special for Keyboard 7f2585, #5 Type)3-4196 Aligning Scale - 10 Space (O.S. - Sup. by 3-4331)3-4216 Margin Stop Rack - 12 Space (O.S. - Sup. by.3-4343)3-4228 Tabulator Stop Spring Comb - 12 Space

3-4230 Aligning .Scale - 12 Space (O.S. - Sup. by 3-4332)3-4231 Paper Scale -.12 Space .(O.S. - Sup. by 3-4287 &■ 3-4318)3-4239 Platen Shaft Bearing, Left, Inner (O.S.)3-4241 Back Space Key Lever Down Stop, Rubber3-4241 Margin Release Lever Down Stop, Rubber

3-4241 Paper Bail Arm Pad, Rubber (O.S.)3-4242 Carriage Frame Brace (O.S.)3-4244 Escapement Wheel Assembled - 12 Space

Printed in U.S.A., - Produced by Flexoprint Panel 25 Issued, 1953

REMINGTON PORTABLE TYPQ'ilRITER


PART NO. DESCRIPTION , CABINET LOCATION

3-4248 Carriage Lock Lever Assembled (O.S. - Sup. by 3-4288)3-4249 Carriage Lock Lever Stop Nut (O.S. - Sup. by 3-4291)3-4252 Grip Wire Rod Assembled - Drug Label Platen (Special Equipment) (O.S. - Sup. by 3-4878)3-4258 Platen Assembled - Drug Label Platen (Special Equipment) (O.S. - Sup. by 3-4874)3-4259 Grip Wire Release Lever Bracket Assembled - Drug Label Platen (Special Equipment)

3-4260, Platen Assembled, Complete - Drug Label Platen (Special Equipment) (O.S. - Sup. by 3-4872)3-4262 Line Space Regulator Detent-56 T.-Half Space Line Spac. (Spec. Equip.) (O.S. Sup. by 3-4871)3-4263 Paper Scale Pivot Bracket, Left - 56 Tooth - Half Space Line Spacing (Spec. Equip.) (O.S.)3-4264 Line Space Ratchet Detent Roller-56 T.t-Half Space Line Spac,(Spec, Equip.O.S. Sup. by 3-4350)_3-4267 Carriage Roll Retainer Assembled

3-4269 Feed Roll Release Shaft Assembled (O.S. - Sup. by 3^4306 & 3-4307)3-4271 Draw Cord Clip (O.S.)

3-4275 Aligning Scale - 10 Space (Special for Keyboard #2585,. #9 Type)3-4280 Carriage Stop (O.S.)3-4286 Paper Scale - 10" Carriage - 10 Space

3-4287 Paper Scale - 10" Carriage - 12 Space

3-4288 Carriage Lock Lever - 10" Carriage

3-4290 Carriage Look Spring - 10" Carriage

3-4291 ■ Carriage'Lock Lever Stop Nut -10" Carriage

3-4295 Paper Scale Pivot Bracket, Left

3-4296 Paper Scale Pivot, Left3-4302 Line Space Detent Release Lever

3-4306 Feed Roll Release Shaft Assembled - 10" Carriage

3-4307 Feed Roll Release Shaft Assembled - 11" Carriage

3-4310 Tabulator Stop Spring Comb Assembled - 11'' Carriage

3-4313 Paper Bail Roll Rod - 10" Carriage

3-4314 Paper Bail Roll Rod - 11" Carriage

3-4317 Paper Scale - 11" Carriage - 10 Space

3-4318 ■ Paper Scale - 11" Carriage - 12 Space

3-4324 Platen Shaft, Right - 10" Carriage

3-4325 Platen Shaft, Right - 11" Carriage3-4326 'Platen Clutch Jaws

3-4327 Platen Clutch Cone

3-4330 Platen Head, Right - Drug Label Platen (Special Equipment)3-4331 Aligning Scale - 10 Space

3-4332 ■ Aligning Scale - 12 Space

3-4335 Tabulator Stop Plate - 11" Carriage

3-4341 Margin Stop Rack - 10" Carriage - 10 Space




3-4345 Tabulator Stop Spring Comb, Left - 11" Carriage - 10 Space ^3-4346 Tabulator Stop Spring Comb, Right - 11" Carriage - 10 Space3-4347 Tabulator Stop Spring Comb, Left - 11" Carriage 12 Space3-4348 Tabulator Stop Spring Comb, Right - 11" Carriage - 12 Space

3-4355 Feed Roll Assembled, Front3-4800 Feed Roll Rocker Arm Assembled, Right3-4805 Platen Knob Assembled, Right (O.S. - Sup. by 3-4828)3-4807 Platen Knob Assembled, Complete, Left (O.S. - Sup. by 3-4829)3-4803 Line Space Regulator Assem.-56 T.-Half Space Line Spac. (Spec. Equip.) (O.S. Sup. by 3-4869)

3-4809 Line Space Ratchet Detent Arm Assembled - 56 Tooth (Special Equipment) (O.S. Sup, by 3-4883)3-4810 Ratchet C; Clutch Ring Assem.-56 T.-Half Space Line Spac. (Spec. Equip.) (O.S. Sup. by 3-4349)_3-4811 Line Space Pawl Carrier Assem., Coup.-56 T.-Half Space Line Spac. (Spec. O.S. Sup. by 3-4844)_3-4813 Line Space Regulator Assem., Comp. - 56 Tooth ■- Half Space Line Spac. (Spec. Equip.) (O.S.)3-4819 Feed Roll Assembled, Rear

Issued, 1953. 26 Produced by Flexoprint Panel

REMINGTON PORTABLET/PEVRITER

MODELS ■ " AN, OR AND ER

PART NO. DESCRIPTION' CABINET LOCATION

3-4S23 Back Space Dog Bell Crank Bracket Assembled '

3-4824 Back Space Dog and Bell Crank Assembled3-4826 Space. Key Escapement Operating Arm Bracket Assembled

3-4S2S Platen Knob Assembled, Right3-4829 Platen Knob Assembled, Complete, Left

3-4S30 Letter Spacing Rack Assembled - 10" Carriage - 10 Space

3-4831 Letter Spacing Rack Assembled - 10" Carriage - 12 Space

3-4S32 Letter.Spacing Rack Assembled - 11" Carriage - 10 Space

3-4S33 Letter Spacing Rack Assembled - 11" Carriage - 12 Space

3-4339 Carriage Frame Complete - 10" Carriage

3-4340 Carriage Frame Assembled - 11" Carriage

3-4341 Line Space Regulator Assembled

3-4842- Line. Space Lever Assembled

3-4S43 Feed Roll Release Lever Assembled

3-4844 Line.Space Paivl Carrier Assembled

3-4845 Line Space Regulator Detent Assembled

3-4846 Paper'Trough Assembled - 10" Carriage

3-4847 ■ Paper Trough Assembled - 11" Carriage

3-4350 Paper Bail Arm Assembled - 10" Carriage

3-4851 Paper Bail Arm Assembled - 11" Carriage

3-4852 Platen Ratchet Assembled

3-4356 Platen Assembled - 10" Carriage

3-4S57 Platen Assembled - 11" Carriage

3-4858 Platen Complete - 10" Carriage

3-4359 Platen Complete - 11" Carriage

3-4860 Line Space Ratchet Detent Roll Arm Assembled.

3-4861 Tabulator Stop Rack Assembled - 11" Carriage - 10 Space

3-4862 Tabulator Stop Rack Assembled - 11" Carriage - 12 Space

3-4863 Tabulator Stop Rack Complete - 11" Carriage - 10 Space

3-4864 Tabulator Stop Rack Complete - 11" Carriage - 12 Space

3-4S65 Margin Stop Assembled, Left3-4866 -Margin-Stop Assembled, Right3-4869 Lime Space Regulator Assembled - 56 Tooth

3-4871 Line Space Regulator Detent Assembled - 56 Tooth

3-4872 Platen Complete - 10" Carriage - Drug Label Platen (Special Equipment)

3-4373 Platen'Complete - 11" Carriage - Drug Label Platen (Special Equipment)

3-4874 Platen Assembled - 10" Carriage l Drug Label Platen (Special Equipment)3-4875 Platen Assembled - 11" Carriage - Drug Label Platen (Special Equipment)3-4878 Grip Wire Rod Assembled - 10" Carriage - D.rug Label Platen (Special Equipment)3-4879 ' Grip IVire Rod Assembled - 11" Carriage - Drug Label Platen (Special Equipment)

3-4332 Platen Ratchet Assembled - 56 Tooth

3-4883 Line Space Ratchet Detent Roll Arm Assembled - 56 Tooth

3-4336 Platen Assembled - 10" Carriage (Siamese) (Special Equipment)3-4837 Platen Complete - 10" Carriage (Siamese) (Special Equipment)3-5001 . Tabulator Letter Spacing Rack Release Link Nut

3-5003 Escapement Body Bell Crank Screvi Lock Nut (O.S. - Sup. by 3-5CG5)3^5003 Escapement Fixed Dog Fulcrum Screw Nut

3-5003 Escapement Stepping Dog Screw Nut

3-5003 Line Space Link Screw Nut (O.S.)3-5003 Paper Scale Pivot Nut, Right

3-5003 -Paper Scale Pivoj Screw Nut (O.S.)3-5003 Space Bar Locking-Link Clip Lock Nut (O.S.)3-5003 Tabulator Letter!Spacing Rack Release Lever Screw Nut.3-5005 Escapement Body Bell Crank Screw Lock Nut

3-5005 Escapement Body Operating Screw Lock Nut ■ ■

Printed in U.S.A. - Produced by Flexoprint Panel 27 Issued,

REMINGTON PORTABLE TYPEWiTER



3-5005 Escapement Body Pivot Screw Lock Nut

3-5005 Escapement Body Stop Screw Lock Nut3-5005 Margin Release Bracket Set Screw Lock Nut3-5005 Segment Oscillator Pivot Screw Lock Nut3-5005 Shift Operating Arm Down Stop Screw Nut (O.S.)

3-5005 Space Key Escapement Body Operating Screw Lock Nut _3-5005 Spring Drum Screw Nut _

3-5005 Tabulator Letter Spacing Rack Release Link Lock Nut _

3-5005 Tabulator Stop Rack Adjusting Screw Lock Nut _3-5005 Type Bar Universal Bar Rocker Pivot Screw Lock Nut _

3-5005 Type Bar Universal Bar Screw Lock Nut _

3-5008 Escapement Wheel Screw Nut _3-5008 Line Space Lever Screw Nut _

3-5008 Margin Stop Rack Nut, Outer _3-5008 Segment Pivot Screw Lock Nut _

3-5008 Segment Shift Stop Screw Lock Nut _

3-5009 Line Space Ratchet Detent Roll Arm Eccentric Nut _

3-5010 Carriage Rail Front and Rear, End Screw Nut (#6 x 40) _3-5011 Foot Pad Screw Nut (Repair Nut) _3-5012 Margin Stop Rack Nut, Inner _

3-5102 Ribbon Contro'l Shaft Spacer —

3-5106 Ribbon Spool Shaft Tension Spring Collar ■ _3-5108 Ribbon Shift Support Bearing Screw Washer _3-5112 Feed Roll Release Shaft Spacer (O.S.) -3-5115 Clutch Gear Washer (O.S. - Sup. by 3-5139) —

3-5119 Paper Bail Arm and Roll Rod Screw Washer3-5121 Line Lock Actuating Stop Collar - Machine without Tabulator (O.S.) _3-5121 Margin Release Shaft Stop Collar (O.S.)3-5123 Line Space Lever Mounting Washer (O.S.)3-5126 Feed Roll Release Lever Spacer

3-5127 Carriage Rail Front and Rear, End and Center Screw, Look Washer3-5129 Tabulator Stop Rack Mounting Screw Lock Washer

3-5130 Line Space Ratchet Detent Arm Spacer - 56 Tooth - Half Space Line Spac. (Spec. Equip.) (0.S.)_3-5136 Platen Spacer, Left3-5137 Platen Spacer, Thick, Right

3-5138 Platen Spacer, Thin, Right3-5139 Platen Ratchet Spacing Collar

3-5140 Platen Ratchet Spacing Collar (Oversize)3-5141 Platen Ratchet Spacing Collar Shim

3-6001 Paper Table Detent Spring (O.S. - Sup. by 3-6064)

3-6001 Segment Operating Arm Yield Spring (O.S.)3-6003 Margin Release Key Lever Spring

3-6004 Tabulator Stop Set and Clear Finger Torsion Spring3-6005 Paper Bail Roll Friction Sleeve3-6006 Paper Bail Arm Spring (O.S. - Sup. by 3-6080)

3-6007 Feed Roll Tension Spring

3-6008 Line Space Ratchet Detent Roll Arm Return Spring (O.S. - Sup. by 3-6076)3-6009 Touch Control Spring

3-6014 Line Space Lever Spring (O.S.)3-6014 Shift Link Yield Spring (O.S.)

3-6015 Shift Look Lever Spring

3-6016 Shift Lever Spring

3-6017 Shift Operating Arm Spring

3-6019 Paper Scale Spring

3-6023 Space Bar Lever Spring (O.S. - Sup. by 3-6073)


REMINGTOM.PORTABLE TYPEWRITER

MODELS ■ AN, OR AND ER

PART NO. DESORiPTiON OABINET LOCATION

3-6024. Paper Side Guide Spring (O.S.)3-6025 Ribbon Spool Retaining Pawl Spring3-6026 Carriage Release Lever Spring, Right (O.S.)3-6027 Clutch Spring (O.S. - Sup. by 3-6074). '3r6029 . Line Space Pawl Spring (O.S. - Sup. by 3-6077)

3-6032 Bell Hammer Spring

3-6034 Ribbon Spool Shaft Tension Spring

3-6035 Line.Lock Slide Spring

3-6036 Escapement Stepping Dog Spring

3-6037 Escapement Fixed Dog Spring ■

3-6038 Escapement Body Spring

3-6039 Back Space Dog Spring

3-6041 OarrI age Tension Spring

3-6042 Line Space Regulator Arm Detent Spring (O.S. - Sup. by 3-6076)3-6046 Top Cover Spring (O.S.)

3-6047 Ribbon Carrier Detent Spring

3-6048 Paper Trough Tension Spring (O.S.)3-6049. . Tabulator-Operating Lever Spring

.3-6050 Bell Hammer Spring Retainer

3-6050.. . Tabulator Operating Lever Spring Retainer

3-6050 Touch Control Spring Retainer

3-6051 . Manual Ribbon Reverse Arm Detent Spring

3-6053 Type,Bar Universal Bar Rocker Spring ■ . _

3-6054 Margin Stop Spring

3-6058 Key Lever Spring - Fourth Bank

3-6062 Space Bar Shaft Spring

3-6063 .. Dea.d Key Spring (Special Equipment)3-6064. Paper Table Detent Spring (O.S.)3-6065 Grip Wire" Release Lever Spring - Drug Label Platen (Special Equipment) ■

3-6066 . . Carry.)NG Case Machine Front Lock Spring, Right

3-6067 Carrying Case Machine Front Lock Spring, Left3-6068 . .Line.Space Regulator Spring-56 T.- Half Space Line Spac. (Spec. Equip.) (O.S. Sup. by 3-6076)_3-6071, Paper Bail Spring (O.S. - Sup. by 3-6080)3-6072 . . Carriage Release Lever Spring, Left3-6073 Space Bar Lever Spring

3-6074 Platen Clutch Cone Retaining Spring

3-6075 Platen Clutch Dog Retaining Spring

3-6076. Line Space Ratchet Detent Roll-Arm Spring

3-6077 Line Space Pawl Spring

3-6079 Feed Roll Tension Spring - 11" Carriage

3-6080 Paper Bail Spring

3-6081 Feed Roll Release Lever Silencer Spring

3-.6102 Type Bar Fulcrum Wire3-6103 Bell Crank Fulcrum Wire

3-6105 Key Lever Fulcrum Wire

'3-6106 Type Bar Cushion Wire

3-6111 Margin Release Connecting Wire

3-6112 Space Bar Locking Link (O.S.)3-6113 Tabulator Stop Fulcrum Wire - 10" Carriage3-6115 Tabulator Stop Fulcrum Wire - 11" Carriage

3-7013 Back Space Dog Bell Crank Screw (O.S.)3-7013 Line Lock Slide Mounting Screw

3-7014 Touch Control Lever Screw (O.S.)3-7018 Carriage End Cover Screw

3-7018 ' Paper Table Screw

3-7019 Carriage and Side Plate Screw ■ -




PART "NO. DESCRIPT1 ON CAB I NET LOCATION

3-7019 Margin Release Bracket Support Screw3-7019 Segment and Type Bar Universal Bar Support Screw3-7019 Segment Roller Guide Bracket Screw3-7019 Tabulator Stop Set and Clear Shaft Support Bracket Screw (O.S.)3-7022 Aligning Scale Bracket Screw (For Keyboard #2585, #9 Type)

3-7022 Aligning Scale Bracket Screw (O.S.)3-7022 Aligning Scale Screw

3-7022 Carriage Rear Cover Screw

3-7022 Front Cover Screw (O.S. - Sup. by 3-7023)

3-7022 Paper Scale Pivot Bracket Right, Screw

3-7022 Side Cover Screw, Front3-7022 Side Cover Screw, Lower, Front (O.S.)3-7023 Carriage Frame Brace Screw (O.S.)3-7023 Carriage Stop Mounting Screw (O.S.)

3-7023 Front Cover Screw

3-7023 Key Lever Comb and Up Stop Screw

3-7023 Ribbon Control Lever Bracket Screw

3-7023 Ribbon Spool Shaft Support Bracket Screw

3-7023 Shift Lock Latch Strike Screw

3-7023

3-7023 Side Cover and Rear Cover Screw, Upper3-7023 Side Plate and Support Screw

3-7023 Top Cover Hinge Bracket Screw, Lower3-7026 Segment Oscillator Pivot Screw

3-7027 Segment Shift Stop Screw

3-7031 Escapement Wheel Screw

3-7032 Spring Drum Screw

3-7034- Line Space Lever Screw

3-7035 Line Space Link Screw (O.S.)3-7041 Segment Pivot Screw

3-7043 Escapement Fixed Dog Fulcrum Screw

3-7044 Escapement Stepping Dog Screw

3-7045 Escapement Body Operating Screw

3-7045 Escapement Body Stop Screw

3-7045 Shift Operating Arm Down Stop Screw (O.S.)

3-7045 Space Key Escapement Body Operating Screw

3-7045 Tabulator Stop Rack Adjusting Screw (O.S. - Sup. by 3-7078)3-7047 Grip Wire Release Lever Bracket Screw - Drug Label Platen (Special Equipment)3-7047 Line Space Stop Screw (O.S. - Sup. by 3-7095)3-7047 Segment Guide Eccentric Screw

3-7047 Shift Lock Latch Strike Screw (O.S. - Sup. by 3-7023)3-7047 Type Bar Cushion Bracket Screw ^3-7047 Type Bar Guide Screw

3-7048 Escapement Body Bell Crank Screw (O.S. - Sup. by 3-7090)3-7051 Shift Lever Arm Link Screw

3-7051 Shift Link Pivot Screw (O.S.)

3-7052 Aligning Scale Screw (For Keyboard #2585, #9 Type)3-7052 Aligning Scale Screw (O.S. - Sup. by 3-7022)3-7054 Ribbon Shift Support Bearing Screw

3-7055 Front Rail Screw, Front

3-7057 Segment Shift Bracket and Support Screw (O.S.)3-7059 Top Cover Hinge Bracket Screw, Upper3-1061 Space Bar Screw

3-7062 Tabulator Letter Spacing Rack Release Lever Screw

3-7063 Carriage Stop Screw (O.S. - Sup. by 3-7091)

Issued, 1953 ' 30 Produced by Flexoprint Panel

REMiNGTON PORTABLE TYPEWRITERMODELS ■ AN, OR AND ER'


.3--7064 . - . Feed.Roll Release Lever Screw (O.S.)3-7064 , . Letter Spacing Rack Release Lever Screw (O.S.) ' '3-7065 Bell Hammer Screw (O.S.) ^3-7066 . Back Space Bell Crank Bracket Screw3-7066 Escapement Body Bracket Screw

3-7066 Line Lock Actuator Stop Eccentric Screw

3-7066 Ribbon Control Shaft Lever Stop Screw

3-7066 Shift Operating Shaft Locking Plate Screw

3-7066 Spring Drum Assembled Mounting Screw

3-7067 . Bell Crank Bracket Screw

3-7068 Space Bar Pivot Screw, Right (O.S.)3-7070 .Type Bar Universal Bar and Rocker Screw

3-7071 . Line Space Ratchet Detent Release Lever Screw (O.S.)3-7072. Foot Pad Screw (O.S.)

3-7072 . -Rear Foot Pad Screw - 10" Carriage (O.S. - Sup. by 3-7093)

3-7073 -Paper Bail Arm and Roll Rod Screw

3-7075. Oarriage Release Lever and Letter Spacing Rack Screw (O.S.)3-7076 Platen Head Set Screw, Right3-7076 Platen Knob Set Screw (O.S.)3-7076 . . Platen Knob Set Screw, Right - ' ■

3-7077. Escapement Body Pivot Screw

3-7077 Margin Release Bracket Set Screw

3-7077 - Type Bar Universal Bar Rocker Pivot Screw

3-7078. . Tabulator Set and Clear Shaft Actuator Key Stop Screw (O.S.)3-7078 Tabulator Stop Rack Adjusting Screw

3-7079 Carriage Rail Front and Rear, Center Screw3-7080- Carriage Rail Front and Rear, End Screw3-7081 Feed Roll Release Shaft Collar Set Screw (O.S.)

3-7081--. - ..Line.Look Actuator Stop Collar Set Screw - Machine without Tabulator (O.S.3-7.081 . -Margin Release Shaft Stop Collar Set Screw (O.S.) '

3-7081 . -. -Ribbon Actuator Arm Hub Set Screw

3-7081 Ribbon Spool Ratchet Hub Set Screw

3-7081 . ...Ribbon Spool Shaft Tension Spring Collar Set Screw

3-7082 .- -Foot.Pad Screw (Repair Part)3-7083. Carriage Lock Lever Screw - 10" Carriage (O.S.)

3-7085 Tabulator Stop Rack Mounting Screw

3-7086 -. . Feed Roll Support Arm Set Screw

3-7086. . . Feed Roll Support Arm Stop Set Screw (O.S.)3-7086 .Tabulator Stop Set and.Clear Shaft Actuating Key Set Screw

3-7087 . Carriage Stop Screw, Right - Oversize (O.S. - Sup. by 3-7092)

3-7089 Shift Stop Screw (O.S. - Sup. by 3-2008)3-7090 Escapement Body Bell Crank Screw

3-7091 Carriage Stop Screw (O.S.)3-7092 .Carriage Stop Screw, Right - Oversize (O.S.)-3-7093 Foot Pad Screw, Front and Rear

3-7093 . . ..Front Rail and Front Foot Pad Screw - 10" Carriage

3-7094. - Paper Scale Pivot, Right3-7095 Line Space Regulator Detent Screw

3-7096 ■ ..Right Carriage End Cover Screw, Rear3-7101 Back.-Space Key Lever Bell Crank Retaining Ring (O.S.)

3-7101 Carriage Release Lever Retaining Ring

3-7101 - Carrying Case Machine Front Lock Latch Fulcrum Pin Retaining Ring

3-7101. . -Feed. Roll Release Lever Retaining Ring.

3-7101 -. .Line .Space Ratchet Detent Roll Arm Release Lever Retaining Ring (O.S.)3-7101 .Margin Release Connecting Wire Clip Retaining Ring

Printed in U.S.A. Produced by Flexoprint Panel 31 Issued, 1953



PART NOi, DESCRIPTION CABINET LOCATION

3-7101 Ribbon Control Bell Crank Retaining Ring

3-7101 Ribbon Reverse Actuator Link Retaining Ring3-7101 Tabulator Letter Spacing Rack Release Link Retaining Ring3-7103 Back Space Dog Bell Crank Retaining Ring3-7103 Feed Roll Support Arm Retaining Ring (O.S.)

3-7103 Shift Lever Shaft Retaining Ring

3-7103 Space Bar Shaft Retaining Ring

3-7103 Tabulator Bell Crank Retaining Ring

3-7103 Tabulator Stop Set and Clear Finger Lever Retaining Ring

3-7105 Margin Release Connecting Wire Clip

3-7105 Space Bar Locking Link (O.S.)3-7113 Bell Hammer Retaining Ring

3-7113 Paper Bail Control Lever Shaft Retaining Ring

3-7113 Ribbon Control Lever Retaining Ring

3-7113 Ribbon Universal Bar Retaining Ring

3-7113 Touch Control Lever Retaining Ring

3-7114 Shift Lever Shaft Retaining Ring (O.S. - Sup. by 3-7103)3-7115 Clutch Gear Retaining Ring (O.S. - Sup. by 3-7122)3-7116 Line Space Regulator Detent Keeper - 56 T. - Half Space Line Spacing (Spec. Equip.) (O.S.)3-7118 Key Lever Fulcrum Wire Keeper (O.S. - Sup. by 3-7121)

3-7118 Type Bar Bell Crank Fulcrum Wire Keeper (O.S. - Sup. by 3-7121)3-7118 Type Bar Fulcrum Wire Keeper (O.S. - Sup. by 3-7121)3-7119 Shift Link Keeper

3-7120 Top Cover Haue Plate Fastener (O.S.)3-7121 Key Lever Fulcrum Wire Keeper

3-7121 Tabulator Stop Fulcrum Wire Keeper

3-7121 Type Bar Bell Crank Fulcrum Wire Keeper

3-7121 Type Bar Fulcrum Wire Keeper

3-7122 Platen Ratchet Retaining Ring

3-8005 Carriage Release Lever Finger Pad (O.S. - Sup. by 3-8006)

3-8005 Feed Roll Release Lever Finger Pad (O.S. - Sup. by 3-8006)3-8005 Line Space Regulator Finger Pad (O.S.)3-8005 Line Space Ratchet Detent Roll Arm Release Lever Finger Pad

3-8005 Manual Ribbon Reverse Arm Finger Pad

3-8005 Margin Stop Finger Pad (O.S.)

3-8005 Ribbon Control Lever Finger Pad

3-8005 Tabulator Stop Set and Clear Finger Lever Finger Pad

3-8005 Touch Control Lever Finger Pad

3-8006 Carriage Release Lever Finger Pad

3-8036 Feed Roll Release Lever Finger Pad

3-9001 Carriage Dowel

3-9005 Type Bar Guide Dowel

3-9009 Carriage End Cover Stud

3-9122 Ribbon Control Link Pivot Screw Stud

3-9155 Ribbon Control Lever Pivot Stud

3-919'2 Line Space Regulator Detent Pivot Stud - 56 T. - Half Space Line Spac. (Spec. Equip.) (O.S.)3-9194 Carrying Case Machine Front Lock Latch Fulcrum Pin

3-9197 Line Space Ratchet Detent Release Lever Pivot Stud-56 T.-Half Space Line Spac. (Special 0.S.)_3-9323 Rear Cover Assembled (Foreign Assembly Plants Only)3-9853 . Carrying Case Assembled, Complete (O.S. - Sup. by 3-9856 & 3-9859)

3-9856 Carrying Case Assembled - 11" Carriage

3-9859 Carrying Case Assembled - 10" Carriage

3-9946 Carrying Case Machine Front Lock Latch, Right3-9947 Carrying Case Machine Front Look Latch, Left3-9948 Desk Mount Machine Front Lock Bracket, Right (Special Equipment)





3-9949 Desk Mount Machine Front Lock Bracket, Left (Special Equipment)3-9950 Desk Mount Machine Rear Lock (Special Equipment) (O.S. - Sup. by 3-9955)3-9955 Disk Mount Machine Rear Lock (Special Equipment)3-9961 Carrying Case Lock Key

4-10979 Carriage Stop Screw (O.S.)

4-11258 Platen Spacer Shim, Right4-11745 Paper Scale Spri.ng Anchor

4-11769 Spring Drum-'Screw Washer

4-11800 Carriage Release Lever Pivot Screw, Left2-40004 Line Space Ratchet Detent Roll Arm Screw

2-40224 Manual Ribbon Reverse Arm Bracket Screw

2-40224 Tabulator Stop Spring Comb Support Screw

2-40260 Ribbon Control Lever Stop Screw (One Color Ribbon Machines)2-40806 Segment Roller Retainer

2-40904 Carriage Rear Cover Spacer

2-40936 Segment Oscillator Spacer Washer, Thick2-40978 Segment Oscillator Spacer Washer, Thin2-40997 Feed Roll Release Lever Spring Washer (O.S. - Sup. by 3-6081)2-46432 Platen Core Screw - Drug Label Platen (Special Equipment)2-48045 Ribbon Spool Shaft Support Bracket Screw, Upper (O.S. - Sup. by 3-7023)

2-50004 Tabulator Stop Set and Clear Link Keeper

2-50006 Line Lock Lever Retaining Ring

2-51940 Key Lever Spring - First, Second and Third Bank2-51940 Tabulator Key Lever Spring

2-51957 Back Space Key Cap - 44 Key Machine (O.S. - Sup. by 2-52015)

2-51957 Key Lever Key Cap - 42 and 44 Key Machines (Specify Character) (O.S. - Sup. by 2-52015)2-51957 Margin Release Key Cap - 44 Key Machine (Foreign and Domestic) (O.S. - Sup. by'2-52015)2-51957 Shift Lock Key Cap - 42 and 44 Key Machines (O.S. - Sup. by 2-52015)

2-51957 Tabulator Key Cap (O.S. - Sup. by 2-52015)2-51958 Shift Lever Key Cap (O.S. - Sup. by 2-52016)

2-51960 Back Space Key Cap - 42 Key Machine (O.S. - Sup. by 2-52018)2-51960 Margin Release Key Cap - 42 Key Machine (Foreign and Domestic) (O.S. - Sup. by 2-52018)2-51967 Molded Key Cap (Small Size) For Special Characters (O.S. - Sup. by 2-52019)2-52015 Back Space Key Cap - 44 Key Machine

2-52015 Key Lever Key Cap - 42 and 44 Key Machines (Specify Character)

2-52015 Margin Release Key Cap (Foreign and Domestic) 44 Key Machine2-52015 Shift Lock Key Cap - 42 and 44 Key Machines

2-52015 Tabulator Key Cap - 42 and 44 Key Machines

2-52016 Shift Lever Key Cap - 42 and 44 Key Machines

2-52018 Back Space Key Cap - 42 i<EY Machine

2-52018 Margin Release Key Cap (Foreign and Domestic) 42 Key Machine2-52019 Molded Key Cap (Small Size) For Special Characters2-55465 Paper Bail Scale Screw


Documents

REMINGTON PORTABLE TYPEWRITER - Xavier University · TYPEWRITER MODELS AN.QR and ER ( REVISED MAY, 1953 ) DIVISION Or SPERRY RAND CORPORATION 315 FOURTH AVENUE NEW YORK, N. Y. AP-92