SPEEDDURABILITY

www.transforcool.com 125, chemin du Tremblay, suite 100, Boucherville (Quebec) J4B 7K4 CANADATel. : 450 274-6190 / Toll free : 1 855 322-COOL / email : info@transforcool.com

Truck body Chassis-cab Straight truck

Reinventing refrigerated trailer

Trailer

2

INNOVATIVE SOLUTIONS FOR TEMPERATURE CONTROLLED TRANSPORTATIONPROFESSIONALS

Carriers specialized in refrigerated transportation need

high-performance equipment, in terms of temperature

control as well as strength and durability of the materials

used, ergonomics for drivers and delivery staff, and ease

of maintenance and repair.

Resulting of years of experience, research and

development and optimization, the refrigerated trailers

developed by Lamberet and Transforcool for the North

American market are designed to meet the highest

international standards, such as the food and health

safety standards set out by the HACCP or the ATP

(Agreement on Transportation for Perishable Goods,

signed by 50 countries from around the globe, including

the United States), while considering the significant

constraints of intensive urban delivery.

The Transforcool trailers, designed for distribution

professionals, are built with reinforced areas where impact

and wear are greatest, and offers the best options for

urban transportation and delivery: single or multi

temperature, customized interior design, options and

accessories for loading and unloading…

Our mission: to quickly provide our clients with superior

quality refrigerated trailers, designed to specifications that

fit their needs and exceed their expectations. We aim for

the highest degree of satisfaction for our products, as well

as our service. We strive to build a network of excellence

in partnerships, through an approach that emphasizes

Research and Development as we rise to the forefront of

a market that is increasingly demanding and technology

savvy.

100% composite, for performance and economy:

Accurate controlled temperature down to the exact degree

Easy maintenance and reducedoperating costs

Zero HCFCs, and reduced CO2 emissions

Compliant with HACCP (Hazard Analysis & Critical Control Points) hygiene standards

3

High-performance 100% composite panelsThe composite insulating panels, tested and proven in laboratory, are the result of years of experience, research and development. They are truly a mastery of the technology exclusively dedicated to cold. Combining composite materials with complex assembly and high insulating properties, this technology gives our panels unrivaled advantages.

Insulation High-performance insulation coefficient, more effective than injected foam between two metallic surfaces. Guarantees rapid temperature pull down and maintains cold longer than steel panelling.

StrengthBoth inside and outside coatings are shock resistant and will keep their original appearance over time. The panels are made with both insulating and structural elements that are highly resistant to compression. Because they are totally sealed during the manufacturing process, there is no risk of water infiltration in the walls. All of the embeddings have been shaped and formed to fit.

Polyurethane Foam 0% HCFC Our manufacturing process controls and optimizes the foam density at all points, giving homogeneous and identical insulation properties throughout the body for a highly efficient insulation. The trailer strictly contains 0% HCFC.

Food Industry 100% composite coating is metal and corrosion-free. No risk for pollution or degradation of the transported goods. The rot-proof coating totally protects against humidity, condensation and water.

Maintenance Washable with high-pressure water and detergent without any risk of corrosion, resistant to natural and chemical products. No infiltration risk between the panels. Repairs are quick, reducing down time.

IMPACT OF THE TRANSFORCOOL ISOTHERMIC QUALITIES ON REFRIGERATED UNIT

• Reduction in running time and fuel consumption

• Reduction of service frequency, leading to reduced maintenance costs

• Reduced rental costs

4

HEAVY-DUTY GALVANIZED CHASSIS – MADE IN CANADA

Reinforced front end, to absorb shocks of 5th wheel coupling.

Built to your specifications: suspension, disc or drum brakes, axles configuration, dolly, LED lighting.

CX SYSTEM FRONT PROFILE

The integrated vertical CX profiles on the front face of the trailer body vectorize the air flow laterally out and act on the vortex generated between the tractor and the trailer to optimize the overall air penetration coefficient.

SIDE DOORS

• Standard or sliding, piano hinges

• Various options available for steps and ladders

SAFETY: LATERAL SIDE GUARDS FOR CYCLISTS

• Safety device to prevent collisions with cyclists

• 2 aluminum bars

Side guards for cyclists

Sliding side door

Aerodynamic CX profile

5

Rear door energy-saving gasket

Benefits

REINFORCED REAR STAINLESS STEEL FRAME DESIGNEDTO WITHSTAND REPEATED DOCKING

Our rear frame combines strength, shock-resistant, easy and quick maintenance, all with low operating cost.

• Bolted, anti-racking, with no welds, therefore no weaknesses, it provides quick and less expensive maintenance. For optimal shock absorption, the vertical uprights are made of stainless steel H-shaped beams and attached directly to the reinforced edge of the panel.

• The frame is protected by 60-mm (2.36 inch) bumpers.

HRE – HIGH RESISTANCE ELASTOMER –ROLLER BUMPERS

Absorbs horizontal shocks and vertical rolls on 1 or 2 levels. The thick galvanized steel tubes house a honeycombed elastomer core, offering unparalleled durability. The high-inertia reinforcement braces dissipate any residual forces.

PROTECTED REAR DOOR

During docking, the steel double hinge of the rear doors keep the doors away from the dock, and the integrated latch keeps the doors fully opened to the sides.

High resistance rolling bumpers

Protected rear door

Roll-up rear door with reinforced stainless steel frame

6

The strongest structural floor on the market: up to 44% more resistant than a standard floor

Our floors are designed to withstand from 14% to 43% greater load

than standard refrigerated trailer:

32,000 lb/ft2 resistance (linear) / Compared to standard floor rate,

which average around 18,000 to 24,000 lb/ft2 (linear)

• Threshold with gasket thermal bridge rupture

• Corundum, aluminum or hybrid floors; different configurations

available, depending on your needs

• Accessories: front and/or back floor drains, aluminum or

polyester cargo tracks, anchoring rings

Internal airflow

• Aerodynamic stoppers to protect against impact of pallets on

the bottom of the bulkhead

• Internal grid at the bulkhead for a continuous protection

between the stoppers and the return air flow

• Patented IAFO (Internal Air Flow Optimizer) system: Maintains

constant overall temperature. Reduces energy consumption.

Can maintain the same temperature at the front and at the rear

of a 53-foot trailer. +25% improvement of the temperature at the

rear of the trailer (temperature control sensor located at 48 feet

from the front of the trailer, in the middle of the side wall)

Multi-temperature

• Prep kits on the floor and ceiling to accommodate all types of

separators (Randall partition systems)

• Recessed evaporators

• Movable or fixed partition

• Lengthwise fixed partition

• Cross-sectional fixed partition

• Full-width mobile partition

Independent or joint half partitions

Patented IAFO system; front interior surface grid and aerodynamic bumpers

Rear and/or front floor drainThreshold with gasket for thermal bridge rupture

Hybrid floor: Corundum non-slip coating and aluminum reinforcement treshold plate

OPTIONAL ACCESSORIES

Protection and interior fittings• Kick plates, loading rails, logistics anchor bars• Available fittings to customize for your specific needs: - Double stacking floor - Meat rail system and water threshold

Anchor rail

7

AvailableRear doors Roll-up, 2 or 3 panel swing door, hybrid, our products meet all your needs to optimize your profitability.

Depending on the equipment selected, some rear doors may not be available.

Bi-temperature and meat rail system

Reinforced bulkhead gridReinforced kick plate

Recharging station for lift truck

Wider three-step access ramp Sliding glad hand

Full width movable partition

Double opening aluminum tank

Transforcool Industries cannot be held responsible for any error or omission contained in this document. The information in this document may be changed without notice, and the products may differ from the ones that appear in the pictures in this document.

Disclaimer:

Transforcool’s products are easy to maintain, to reduce down time and repair costs, inareas such as front end, lighting, rear frameand doors:

The vertical CX profiles have an integrated rail, making additional equipment unobtrusive and easy to install. Lights, bumpers, ladders and electrical equipment can be installed without drilling holes and compromising the insulation. This makes it even easier to add or change such equipment much faster.

The aluminum profiles house a technical duct for wiring passway. These ducts are easy to access, non intrusive and do not require foam removal at the front end. Cables and wiring at the front end go through these ducts: dome lights, marker lights and S/T/T lights.

EASY MAINTENANCE

Innovative bolted frame, easily and quickly dismountable, with no welds.

To optimize ease of maintenance, all lighting is controlled through quick connect harness wiring.

Doors: Double stainless steel hinges, double reinforced wear bushings. Slack adjusters to maintain tightness in case of impact or deformation of the frame or hinges.

Doors: Recessed lock rod and handle – can be changed in 30 minutes if damaged.

Composite panel repair: Back to its original appearance after just 1 day in the shop following an impact.

Bolted 5th wheel kingpin.

All in all, a drastic down time reduction.