Upload
wandee2393
View
233
Download
0
Embed Size (px)
Citation preview
8/10/2019 REFRIGERATOR REPORT
1/21
THERMODYNAMICS IIVARIATION IN REFRIGERATION COEFFICIENT OF PERFORMANCE AT VARIOUS
OPERATING CONDITIONSEMD5M5A
1.0Title
MEC 554-THERMALFLUIDS LAB
THERMODYNAMICS II LAB
VARIATION IN REFRIGERATION
COEFFICIENT OF PERFORMANCE AT
VARIOUS OPERATING
LECTURER: SITI HAJAR BINTI MOHD YUSOP
8/10/2019 REFRIGERATOR REPORT
2/21
THERMODYNAMICS IIVARIATION IN REFRIGERATION COEFFICIENT OF PERFORMANCE AT VARIOUS
OPERATING CONDITIONSEMD5M5A
2.0Abstract
The potential increase in COP is the greatest in applications where the heat sink
and heat source temperatures are approximately equal and of relatively large magnitude.
The minimum requirements to achieve these performance improvements are the selection
of a mixture that yields the desired temperature change in both heat exchangers, a
counter-flow heat exchanger that takes advantage of the temperature glide of the
refrigerant and minimized degradation of the heat transfer process. The magnitude of the
phase change temperature glide is related to the differences in the normal boiling points
of the mixture constituents.
8/10/2019 REFRIGERATOR REPORT
3/21
THERMODYNAMICS IIVARIATION IN REFRIGERATION COEFFICIENT OF PERFORMANCE AT VARIOUS
OPERATING CONDITIONSEMD5M5A
Table of Contents
1.0 Title................................................................................................................................. 1
2.0 Abstract .......................................................................................................................... 2
List of Symbols ........................................................................................................................... 4
List of figure ............................................................................................................................ 5
3.0 Inreoduction and Applications .................................................................................... 6
4.0 Objectives ...................................................................................................................... 7
5.0 Theory ............................................................................................................................ 7
6.0 Experimental Procedures ...................................................................................... 11
6.1 Apparatus/Experimental Setup...................................................................... 11
6.2 Procedure .......................................................................................................... 13
7.0 Result ............................................................................................................................ 15
7.1 Data recorded .................................................................................................... 15
8.0 Discussion ..................................................................................................................... 18
9.0 Conclusion .................................................................................................................... 18
10.0 References .................................................................................................................... 19
11.0 Appendices .................................................................................................................. 20
8/10/2019 REFRIGERATOR REPORT
4/21
THERMODYNAMICS IIVARIATION IN REFRIGERATION COEFFICIENT OF PERFORMANCE AT VARIOUS
OPERATING CONDITIONSEMD5M5A
List of Symbols
A Area over which force (F) acts (m2)
E Elastic modulus (GPa)F Force (N)
() Initial dimension in direction i (mm)
T Specimen thickness (m)
Rate of chart displacement (mm/min)
Rate of sample displacement (mm/min)
w Specimen width (m)
Displacement of chart (mm) Displacement of sample (mm)
Strain
=0 Predicted strain at zero stress
Normal strain in direction i
E Error in the predicted elastic modulus (GPa)
F Error in the force (N)
Change in dimension in direction i (mm)t Error in the specimen thickness (m)
w Error in the width (m)
=0 Error in the predicted strain at zero stress
Error in the predicted intercept of stress-stain data (MPa)
Error in the stress (MPa)
Predicted intercept of stress-strain data (MPa)
Engineering stress (MPa) Yield point (MPa)
Ultimate strength (MPa)
8/10/2019 REFRIGERATOR REPORT
5/21
THERMODYNAMICS IIVARIATION IN REFRIGERATION COEFFICIENT OF PERFORMANCE AT VARIOUS
OPERATING CONDITIONSEMD5M5A
List of figure
Figure 1: Refrigerator ................................................................................................................. 6
Figure 2: Schematic diagram of refrigeration cycle ................................................................... 8
Figure 3: Computer controlled refrigeration and air conditioning unit [two condenser (water
and air) and two evaporator] / THAR22C ................................................................................ 11
Figure 4: Schematic diagram of computer controlled refrigeration and air conditioning unit
[two condenser (water and air) and two evaporator] ............................................................. 11
Figure 5: The location of valve (AVS3, AVS4, AVS5, AVS 6) ..................................................... 12
Figure 6: Computer system ...................................................................................................... 12
http://d/UiTM%20Mohd%20Kaswandee%20Razali/Sem%205/MEC554-Thermalfluids%20Lab/Report%202-Refrigerator/R2-Complete%20all.docx%23_Toc400996294http://d/UiTM%20Mohd%20Kaswandee%20Razali/Sem%205/MEC554-Thermalfluids%20Lab/Report%202-Refrigerator/R2-Complete%20all.docx%23_Toc400996296http://d/UiTM%20Mohd%20Kaswandee%20Razali/Sem%205/MEC554-Thermalfluids%20Lab/Report%202-Refrigerator/R2-Complete%20all.docx%23_Toc400996296http://d/UiTM%20Mohd%20Kaswandee%20Razali/Sem%205/MEC554-Thermalfluids%20Lab/Report%202-Refrigerator/R2-Complete%20all.docx%23_Toc400996297http://d/UiTM%20Mohd%20Kaswandee%20Razali/Sem%205/MEC554-Thermalfluids%20Lab/Report%202-Refrigerator/R2-Complete%20all.docx%23_Toc400996297http://d/UiTM%20Mohd%20Kaswandee%20Razali/Sem%205/MEC554-Thermalfluids%20Lab/Report%202-Refrigerator/R2-Complete%20all.docx%23_Toc400996298http://d/UiTM%20Mohd%20Kaswandee%20Razali/Sem%205/MEC554-Thermalfluids%20Lab/Report%202-Refrigerator/R2-Complete%20all.docx%23_Toc400996299http://d/UiTM%20Mohd%20Kaswandee%20Razali/Sem%205/MEC554-Thermalfluids%20Lab/Report%202-Refrigerator/R2-Complete%20all.docx%23_Toc400996299http://d/UiTM%20Mohd%20Kaswandee%20Razali/Sem%205/MEC554-Thermalfluids%20Lab/Report%202-Refrigerator/R2-Complete%20all.docx%23_Toc400996299http://d/UiTM%20Mohd%20Kaswandee%20Razali/Sem%205/MEC554-Thermalfluids%20Lab/Report%202-Refrigerator/R2-Complete%20all.docx%23_Toc400996298http://d/UiTM%20Mohd%20Kaswandee%20Razali/Sem%205/MEC554-Thermalfluids%20Lab/Report%202-Refrigerator/R2-Complete%20all.docx%23_Toc400996297http://d/UiTM%20Mohd%20Kaswandee%20Razali/Sem%205/MEC554-Thermalfluids%20Lab/Report%202-Refrigerator/R2-Complete%20all.docx%23_Toc400996297http://d/UiTM%20Mohd%20Kaswandee%20Razali/Sem%205/MEC554-Thermalfluids%20Lab/Report%202-Refrigerator/R2-Complete%20all.docx%23_Toc400996296http://d/UiTM%20Mohd%20Kaswandee%20Razali/Sem%205/MEC554-Thermalfluids%20Lab/Report%202-Refrigerator/R2-Complete%20all.docx%23_Toc400996296http://d/UiTM%20Mohd%20Kaswandee%20Razali/Sem%205/MEC554-Thermalfluids%20Lab/Report%202-Refrigerator/R2-Complete%20all.docx%23_Toc4009962948/10/2019 REFRIGERATOR REPORT
6/21
THERMODYNAMICS IIVARIATION IN REFRIGERATION COEFFICIENT OF PERFORMANCE AT VARIOUS
OPERATING CONDITIONSEMD5M5A
3.0 Inreoduction and Applications
The age, the seasonal harvesting of snow and ice was a regular practice of most of the
ancient cultures: Chinese, Hebrews, Greeks, Romans, and Persians. Ice and snow were stored
in caves or dugouts lined with straw or other insulating materials. The Persians stored ice in
pits called yakhchals. Rationing of the ice allowed the preservation of foods over the warm
periods. This practice worked well down through the centuries, with icehouses remaining in
use into the twentieth century.
In the 16th century the use of ice to refrigerate and thus preserve food goes back to
prehistoric times. Through, the discovery of chemical refrigeration was one of the first steps
toward artificial means of refrigeration. Sodium nitrate or potassium nitrate, when added to
water, lowered the water temperature and created a sort of refrigeration bath for cooling
substances. In Italy, such a solution was used to chill wine and cakes.
During the first half of the 19th century, ice harvesting became big business in
America. New Englander Frederic Tudor, who became known as the "Ice King", worked on
developing better insulation products for the long distance shipment of ice, especially to the
tropics.
Refrigeration is used widely in various applications from industrial to domestic
situations, mainly for the storage and transport of perishable foodstuffs and chemical
substances. It has the prime function to remove heat from a low temperature region, and its
can also be applied as a heat pump for supplying heat to
region of high temperature.
In this experiment we need to investigate the
variation in Coefficient of Performance () of a
vapor compression refrigeration system. The experiment
execute by using THAR22C Computer controlled
refrigeration and air conditioning unit [two condensers
(water and air) and two evaporators].
Figure 1: Refrigerator
8/10/2019 REFRIGERATOR REPORT
7/21
THERMODYNAMICS IIVARIATION IN REFRIGERATION COEFFICIENT OF PERFORMANCE AT VARIOUS
OPERATING CONDITIONSEMD5M5A
4.0 Objectives
The purpose of this experiment is to:
1.
Investigate the variation in Coefficient of Performance (COPR) of a vapour
compression refrigeration system at different coolong load.
5.0 Theory
A refrigeration cycle works to lower and maintain the temperature of a controlled space by
heat transfer from a low to a high temperature region.
High Temperature Reservoir, TH
QH
E W net
QL
Low Temperature Reservoir, TL
Refrigeration duty is another term for the cooling effect of the refrigeration system,
which is the rate of heat being removed from the low temperature region with specified
evaporation and condensation temperatures. The unit for duty measurements is in Watts
(for 1 ton of refrigeration = 3517 W)
The Vapor Compression Cycle
Ideal refrigeration systems follow the theoretical Reversed Carnot Cycle process. In
practical refrigerators, compression and expansion of a gas and vapor mixture presents
practical problems in the compressor and expander. Therefore, in practical refrigeration,
compression usually takes place in the superheated field and a throttling process is substitutedfor the isentropic expansion.
8/10/2019 REFRIGERATOR REPORT
8/21
THERMODYNAMICS IIVARIATION IN REFRIGERATION COEFFICIENT OF PERFORMANCE AT VARIOUS
OPERATING CONDITIONSEMD5M5A
Figure 2: Schematic diagram of refrigeration cycle
8/10/2019 REFRIGERATOR REPORT
9/21
THERMODYNAMICS IIVARIATION IN REFRIGERATION COEFFICIENT OF PERFORMANCE AT VARIOUS
OPERATING CONDITIONSEMD5M5A
The cycle ;
12 Condensation of the high pressure vapor during which heat is transferred to the
high temperature region.
23 Adiabatic throttling of the condensed vapor from the condensing to the
evaporating pressure.
34 Evaporation of the low pressure liquid during which heat is absorbed from the
low temperature source.
41 Isentropic compression of the vapor, from the evaporating to the condensing
pressures.
Energy Transfer Analysis
Compressor
q4-1= h4h1 + w
If compressor is adiabatic, q4-1 = 0 and w = h1h4
Power requirement, P = m (h1h4 ), where m is the flow rate of working fluid per unit time.
Condenser
q1-2 = h2h1+ w
w = 0, therefore q1-2 = h2h1and rate of heat rejection Q1-2 = m ( h2h1 )
Expansion valve
q2-3 = h3h2+ w
w = 0 at the expansion valve, and the process is adiabatic
Therefore h3 = h2
.
.
8/10/2019 REFRIGERATOR REPORT
10/21
THERMODYNAMICS IIVARIATION IN REFRIGERATION COEFFICIENT OF PERFORMANCE AT VARIOUS
OPERATING CONDITIONSEMD5M5A
Evaporator
q3-4 = h4h3+ w
w = 0, therefore q3-4 = h4h3 and rate of heat absorbed Q3-4 = m ( h4h3 )
Coeffi cient of Performance (COP)
COP ref= q3-4 = h4h3
w h1h4
8/10/2019 REFRIGERATOR REPORT
11/21
THERMODYNAMICS IIVARIATION IN REFRIGERATION COEFFICIENT OF PERFORMANCE AT VARIOUS
OPERATING CONDITIONSEMD5M5A
6.0 Experimental Procedures
6.1 Apparatus/Experimental Setup
Figure 3: Computer controlled refrigeration and air conditioning unit [two condenser (water and air) and
two evaporator] / THAR22C
Figure 4: Schematic diagram of computer controlled refrigeration and air conditioning unit [two condenser
(water and air) and two evaporator]
8/10/2019 REFRIGERATOR REPORT
12/21
THERMODYNAMICS IIVARIATION IN REFRIGERATION COEFFICIENT OF PERFORMANCE AT VARIOUS
OPERATING CONDITIONSEMD5M5A
Figure 5: The location of valve (AVS3, AVS4, AVS5, AVS 6)
Figure 6: Computer system
8/10/2019 REFRIGERATOR REPORT
13/21
THERMODYNAMICS IIVARIATION IN REFRIGERATION COEFFICIENT OF PERFORMANCE AT VARIOUS
OPERATING CONDITIONSEMD5M5A
6.2 Procedure
6a) Condenser-water and evaporator-water
a. Water as a heat source is selected by opening valves AVS-4 and AVS-5and then
click START.
b.
The water flow rate at the condenser to 5 L/m and 3 L/m at the evaporator
(evaporator load) are adjusted.
c. The COMPRESSOR button is click.
d. The data are start recorded when the system is stabilized by click START
SAVING.e. The sampling rate at 120 second per sample is set.
f.
The data for six minutes (3 samples @ 360 second) are recorded by click STOP
SAVING.
g. The evaporator load is increased to 5 L/m and step (c) to step (f) are repeated.
6b) Condenser-water and evaporator-air
a. Air as a heat source is selected by opening valves AVS-3 and AVS-5and then
click START
b. The water flow rate at the condenser to 5 L/m and the air flow of the evaporator
are adjusted until 50% of the maximal flow (evaporator load).
c. The COMPRESSOR button is click.
d. The data are start recorded when the system is stabilized by click START
SAVING
e.
The sampling rate at 120 second per sample is set.
f. The data for six minutes (3 samples @ 360 second) are recorded by click STOP
SAVING.
g.
The evaporator load is increased to 100% and step (c) to step (f) are repeated.
8/10/2019 REFRIGERATOR REPORT
14/21
THERMODYNAMICS IIVARIATION IN REFRIGERATION COEFFICIENT OF PERFORMANCE AT VARIOUS
OPERATING CONDITIONSEMD5M5A
6c) Condenser-air and evaporator-air
a. Air as a heat source is selected by opening valves AVS-3 and AVS-6and then
click START.
b. The air flow of the condenser is adjusted to maximum flow (100%) and 50% of
the maximal flow at the evaporator (evaporator load).
c. The COMPRESSOR button is click.
d. The data are start recorded when the system is stabilized by click START
SAVING
e.
The sampling rate at 120 second per sample is set.
f.
The data for six minutes (3 samples @ 360 second) are recorded by click STOPSAVING.
g. The evaporator load is increased to 100% and step (c) to step (f) are repeated.
6d) Condenser-air and evaporator-water
a. Water as a heat source is selected by opening valves AVS-4 and AVS-6and then
click START.
b.
The air flow of the condenser is adjusted to maximum flow (100%) and the water
flow rate is adjusted at the evaporator to 3 L/m (evaporator load).
c. The COMPRESSOR button is click.
d.
The data are start recorded when the system is stabilized by click START
SAVING
e. The sampling rate at 120 second per sample is set.
f.
The data for six minutes (3 samples @ 360 second) are recorded by click STOP
SAVING.
g. The evaporator load is increased to 5 L/m and step (c) to step (f) are repeated.
8/10/2019 REFRIGERATOR REPORT
15/21
THERMODYNAMICS IIVARIATION IN REFRIGERATION COEFFICIENT OF PERFORMANCE AT VARIOUS
OPERATING CONDITIONSEMD5M5A
7.0 Result
7.1 Data recorded
Data had been recorded on the provided table of result.(separate sheet)
7.2 Sample calculation
A. Experiment A
Refrigerant mass flow rate, mref (kg/s)
mref = vref / v2
a) vref - change the unit for value SC-1(L/h):
SC-1 = 27.64 L/h
thus vref = 27.64 x (0.001/3600)
= 7.68 x 10-6m3/s
b) v2 taken from table A11 for saturated refrigerant 134-a(provided at
appendices)
At ST-2 = 39.62 oC
=
v2= 0.02017 m3/kg
c) Therefore mref:
mref = vref / v2= (7.68 x 10-6/ 0.02017 )
= 3.808 x 10-4
kg/s
Saturated vapour, vg(m3/kg) Temperature(C)
0.02017 38
v2 39.62
0.019952 40
8/10/2019 REFRIGERATOR REPORT
16/21
THERMODYNAMICS IIVARIATION IN REFRIGERATION COEFFICIENT OF PERFORMANCE AT VARIOUS
OPERATING CONDITIONSEMD5M5A
Evaporator cooling load, Qevap(kW):
a)
The calculation of h3 refer to table A11 for saturated refrigerant 134-a(provided at appendices):
At ST-3 = 7.54 oC
=
h3= 192.72 kJ/kg
b)
The calculation of h4 refer to table A11 for saturated refrigerant 134-a(provided at appendices):
At ST-4 = 12.06 oC
=
h4 = 189.04 kJ/kg
c) Therefore Qevap:
Qevap = mref (h4-h3) = (3.808 x 10-4
) (189.04 - 192.72)= -1.4 x 10-3kW
hfg(kJ/kG) Temperature(C)
193.94 6
h3 7.54
192.35 8
hfg(kJ/kG) Temperature(C)
189.09 12
h4 12.06
187.42 14
8/10/2019 REFRIGERATOR REPORT
17/21
8/10/2019 REFRIGERATOR REPORT
18/21
8/10/2019 REFRIGERATOR REPORT
19/21
THERMODYNAMICS IIVARIATION IN REFRIGERATION COEFFICIENT OF PERFORMANCE AT VARIOUS
OPERATING CONDITIONSEMD5M5A
10.0 References
Websites:
1) http://en.wikipedia.org/wiki/HVAC [Accessed 27/09/14]
2) http://home.howstuffworks.com/refrigerator.htm [Accessed 7/10/14]
3)
http://www.mansfieldct.org/schools/mms/staff/hand/heatrefrig.htm[Accessed 7/10/14]
Books:
4) Eastop & McConkey, Applied Thermodynamics for Engineering Technologists 5 th
Edition, Prentice Hall, 1993.
5)
Yunus A. Cengel, Michael A. Boles,2006, Thermodynamics: An Engineering
Approach 5th Edition, McGraw Hill.
6)
Yunus A. Vengeland Micheal A. Boles, Thermodynamics An Engineering
Approach,7thedition in SI units, 2011 , The McGraw-Hill Companies.
http://en.wikipedia.org/wiki/HVAChttp://home.howstuffworks.com/refrigerator.htmhttp://www.mansfieldct.org/schools/mms/staff/hand/heatrefrig.htmhttp://www.mansfieldct.org/schools/mms/staff/hand/heatrefrig.htmhttp://home.howstuffworks.com/refrigerator.htmhttp://en.wikipedia.org/wiki/HVAC8/10/2019 REFRIGERATOR REPORT
20/21
THERMODYNAMICS IIVARIATION IN REFRIGERATION COEFFICIENT OF PERFORMANCE AT VARIOUS
OPERATING CONDITIONSEMD5M5A
11.0 Appendices
8/10/2019 REFRIGERATOR REPORT
21/21
THERMODYNAMICS IIVARIATION IN REFRIGERATION COEFFICIENT OF PERFORMANCE AT VARIOUS
OPERATING CONDITIONSEMD5M5A