Reference Manual - Full Compass Systems€¦ · AUTO, 480/576i, 480/576p, 720p, 1080i, 1080p, ... H. CROPPING 1–100% This adjusts the crop size of the inset screen. ... SPLIT PATTERN

Copyright © 2019 ROLAND CORPORATION

ContentsMenu List (Setup Screen) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

System (Video, Audio, and Unit) Settings . . . . . . . . . . . . . . . . . . . . . . 2

AUTO MIXING Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

ECHO CANCEL Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

MEMORY SELECT Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

MEMORY LOAD Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Audio Channel 1–4 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Audio Channel 5/6 and 7/8 Settings . . . . . . . . . . . . . . . . . . . . . . . . . 11

Settings for Main Output Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

BUS SELECT Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

AUDIO FOLLOW Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

HDMI Audio Channel 1– 4 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 14

USB Input/Output Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

USB FROM PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

USB TO PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

USER Button Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

MUTE SELECT Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

SOLO SELECT Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

USER Button Advanced Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

AUTO SWITCHING Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

MEMORY LOAD SW Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

MUTE GROUP Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

SOLO GROUP Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

GPO Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Settings for Assignments to Video Input/Output Connectors . . . . 20

RS-232 Command Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Specification of the RS-232 Connector . . . . . . . . . . . . . . . . . . . . . . . 21

Overview of Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Received Commands (Controller g VR-4HD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Sent Commands (VR-4HD g Controller) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Control Using the TALLY/GPIO Connector . . . . . . . . . . . . . . . . . . . . . . . 24

Specification of the TALLY/GPIO Connector . . . . . . . . . . . . . . . . . . . 24

Inputting a Control Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Outputting a Tally Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Outputting a Control Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

MIDI Implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Reference ManualVersion 2.0 and later

2

Menu List (Setup Screen)Display for the various setup screens on the built-in monitor. In these menus change settings for video, audio and for general VR-4HD settings.

* The default value is printed in bold characters.

System (Video, Audio, and Unit) Settings ([SYSTEM SETUP] button g select category)

Category Setting item Value Explanation

Page 1/3

VIDEO CH4 This adjusts the video to input on video channel 4.

INPUT ASSIGN HDMI, RGB, COMPOSITEThis sets the video source to input on video channel 4.

* This is identical to the setting for “INPUT CH4” (p. 20).

RESOLUTION (EDID)

AUTO, 480/576i, 480/576p, 720p, 1080i, 1080p, 640 x 480, 800 x 600, 1024 x 768, 1280 x 768, 1280 x 1024, 1366 x 768, 1400 x 1050, 1600 x 1200, 1920 x 1200

This sets the input format (the EDID to send) of video input via the RGB/COMPONENT input connector or HDMI IN connector.

When this is set to “AUTO,” EDID information for all formats that can be input is sent.

* EDID information is not sent during component signal input.

SCALING TYPE FULL, LETTERBOX, CROP, DOT BY DOT

This sets the scaling type.

FULL: This always displays the picture expanded to full screen, irrespective of the aspect ratio of the input video.

LETTERBOX: This enlarges or reduces the incoming video to a full-screen view while keeping the aspect ratio unchanged.

CROP: This enlarges or reduces the incoming video so that the output picture has no blank margins while keeping the aspect ratio unchanged. Video extending beyond the borders is cut off.

DOT BY DOT: This performs no scaling.

H. POSITION -1920–0–1920 This adjusts the display position in the horizontal direction.

V. POSITION -1200–0–1200 This adjusts the display position in the vertical direction.

H. SIZE 80–100–200 % This adjusts the size in the horizontal direction.

V. SIZE 80–100–200 % This adjusts the size in the vertical direction.

CONTRAST -64–0–63 This adjusts the contrast.

SATURATION -64–0–63 This adjusts the saturation.

BRIGHTNESS -64–0–63 This adjusts the brightness.

FLICK FILTER 0–7–10 This reduces flicker.

INPUT CAPTURE ([EXEC])

You can capture still images from input video on video channel 4.

* Either the captured still image or the still image sent from VR-4HD RCS is temporarily stored in the VR-4HD.If a new still image is captured or is sent from VR-4HD RCS while a still image is already saved, the previously saved still image is overwritten. Also, still-image data is deleted when the power is turned off.

TRANSITION MIX MIX, FAM, NAM, MOSAIC This specifies the transition pattern assigned to the [MIX] button.

WIPE

H-DOWN, H-UP, V-RIGHT, V-LEFT, H-IN, H-OUT, V-IN, V-OUT, R-DOWN, L-DOWN, R-UP, L-UP, BLOCK, V-GRID, H-GRID, H-DOWN s, H-UP s, V-RIGHT s, V-LEFT s, H-IN s, H-OUT s, V-IN s, V-OUT s, R-DOWN s, L-DOWN s, R-UP s, L-UP s, BLOCK s, V-GRID s, H-GRID s

This specifies the transition pattern assigned to the [WIPE] button.

* Setting values indicated with “s” are soft edge transition patterns.

TRANSITION TIME 0.0–4.0 sec This sets the video transition time.

PinPSIZE 1/2, 1/4, 1/3

This sets the size of the inset screen. The horizontal width (and vertical height) of the inset screen are set to 1/2, 1/4, or 1/3 the size values of the background video.

BORDER WIDTH 0–3–15 This adjusts the width of the border for the inset screen.

BORDER COLOR BLACK, WHITE, GRAY, RED, GREEN, BLUE, YELLOW This sets the color of the border for the inset screen.

PREVIOUS SELECT OFF, ON When set to “ON,” the channel of the previously selected inset screen is selected automatically when the [PinP] button is pressed.

Menu List (Setup Screen)

3


PinP H. POSITION -50–0–50 % This adjusts the position of the inset screen in the horizontal direction.

V. POSITION -50–0–50 % This adjusts the position of the inset screen in the vertical direction.

SHAPE SQUARE, DIAMOND, CIRCLE, HEART This specifies the shape of the inset screen.

ASPECT 16:9, 1:1 This specifies the aspect ratio of the inset screen.

H. CROPPING 1–100% This adjusts the crop size of the inset screen.

V. CROPPING 1–100% This adjusts the crop size of the inset screen.

H. VIEW POSITION -50–0–50% This adjusts the horizontal position of the inset screen.

V. VIEW POSITION -50–0–50% This adjusts the vertical position of the inset screen.

VFXEFFECT PATTERN

OFF, NEGATIVE, EMBOSS, COLORIZE, COLOR PASS, POSTERIZE, SILHOUETTE, MONOCOLOR, FINDEDGE

This sets the filter effect applied to the main output video. When this is set to “OFF,” no effect is assigned.

VALUE 0–127

This adjusts the amount of effect applied. Setting this to “0” turns off the effect.

* Pressing the [VIDEO FX/KEY LEVEL] button displays the “VIDEO FX” shortcut for “VALUE” at the bottom of the screen.

Page 2/3

KEY

KEY SOURCE CH OFF, CH1–CH4, STILL

This specifies the channel for the video displayed in the foreground during key compositing.

Setting this to “STILL” performs key compositing using a captured still image or a still image sent from VR-4HD RCS dedicated software.

When set to “OFF,” operating the [KEY] button has no effect.

KEY TYPE CHROMA, LUMI This sets the key type (chroma key or luminance key) for key compositing.

CHROMA KEY LEVEL 0–64–255

This adjusts the degree of extraction (transparency) for chroma key.

* Pressing the [VIDEO FX/KEY LEVEL] button displays, at the bottom of the screen, the “KEY LEVEL” shortcut for either “CHROMA KEY LEVEL” or “LUMI KEY LEVEL,” according to setting for “KEY TYPE.”

CHROMA KEY GAIN 0–255 This adjusts the degree of edge blur for chroma key.

CHROMA KEY COLOR BLUE, GREEN This sets the extraction color for chroma key.

CHROMA KEY HUE WIDTH -127–0–127 This adjusts the hue width (range) for chroma key.

CHROMA KEY HUE FINE -127–0–127 This adjusts the center position of the hue for chroma key.

CHROMA KEY SAT WIDTH -127–0–127 This adjusts the saturation width (range) for chroma key.

CHROMA KEY SAT FINE 0–255 This adjusts the center position of saturation for chroma key.

LUMI KEY LEVEL 0–64–255

This adjusts the degree of extraction (transparency) for luminance key.

* Pressing the [VIDEO FX/KEY LEVEL] button displays, at the bottom of the screen, the “KEY LEVEL” shortcut for either “CHROMA KEY LEVEL” or “LUMI KEY LEVEL,” according to setting for “KEY TYPE.”

LUMI KEY GAIN 0–255 This adjusts the degree of edge blur for luminance key.

LUMI KEY COLOR BLACK, WHITE This sets the separation color for luminance key.

SPLIT PATTERN V. CENTER, H. CENTER, V. STRETCH, H. STRETCH This sets the split composition pattern assigned to the [SPLIT] button.

A-CENTER 0–50–100 %

This is applied when “PATTERN” is set to “V. CENTER” or “H. CENTER.”

5 When at V. CENTERThis adjusts the horizontal position of the video displayed on the left.

5 When at H. CENTERThis adjusts the vertical position of the video displayed above.

B-CENTER 0–50–100 %

This is applied when “PATTERN” is set to “V. CENTER” or “H. CENTER.”

5 When at V. CENTERThis adjusts the horizontal position of the video displayed on the right.

5 When at H. CENTERThis adjusts the vertical position of the video displayed below.

PREVIOUS SELECT OFF, ONWhen set to “ON,” the previously selected channel is selected automatically when the [SPLIT] button is pressed.

* Only the channel displayed to the right or below is automatically selected.

CENTER POSITION -50–0–50% This is valid when "PATTERN" is "V. CENTER" or "H. CENTER." This adjusts the position of the split boundary.


4


VIDEO OUT

OUTPUT RESOLUTION

AUTO, 480/576i (*1), 480/576p, 720p, 1080i (*1), 1080p, 640 x 480, 800 x 600, 1024 x 768, 1280 x 768, 1280 x 1024, 1366 x 768, 1400 x 1050, 1600 x 1200, 1920 x 1200

This specifies the output format of the main output video (HDMI OUT connector or RGB/COMPONENT output connector).

When this is set to “AUTO,” the output format follows the setting made for “SYSTEM FORMAT” (p. 5).

(*1) The “480/576i” and “1080i” formats are supported for HDMI output only.When the setting is “480/576i” or “1080i,” no video is output from the RGB/COMPONENT output connector.

SCALING TYPE FULL, LETTERBOX, CROP, DOT BY DOT

This sets the scaling type for the main output video.

FULL: This always displays the picture expanded to full screen, irrespective of the aspect ratio of the input video.

LETTERBOX: This enlarges or reduces the incoming video to a full-screen view while keeping the aspect ratio unchanged.

CROP: This enlarges or reduces the incoming video so that the output picture has no blank margins while keeping the aspect ratio unchanged. Video extending beyond the borders is cut off.

DOT BY DOT: This performs no scaling.

OUTPUT H. POSITION -1920–0–1920 This adjusts the horizontal position of the main output video.

OUTPUT V. POSITION -1200–0–1200 This adjusts the vertical position of the main output video

OUTPUT H. SIZE 80–100–200 % This adjusts the horizontal size of the main output video.

OUTPUT V. SIZE 80–100–200 % This adjusts the vertical size of the main output video.

OUTPUT CONTRAST -64–0–63 This adjusts the contrast of the main output video.

OUTPUT SATURATION -64–0–63 This adjusts the saturation of the main output video.

OUTPUT BRIGHTNESS -64–0–63 This adjusts the brightness of the main output video.


VIDEO OUT OUTPUT COLOR SPACE AUTO, RGB-FULL, RGB-LIMIT, YCbCr This sets the color space for HDMI OUT connector and RGB/COMPONENT output connector.

OUTPUT DVI-D/HDMI DVI-D, HDMI This sets the output mode of the HDMI OUT connector.

PREVIEW CONTRAST -64–0–63 This adjusts the contrast of the preview output video.

PREVIEW SATURATION -64–0–63 This adjusts the saturation of the preview output video.

PREVIEW BRIGHTNESS -64–0–63 This adjusts the brightness of the preview output video.

PREVIEW COLOR SPACE AUTO, RGB-FULL, RGB-LIMIT, YCbCr This sets the color space for PVW OUT connector.

PREVIEW DVI-D/HDMI DVI-D, HDMI This sets the output mode for PVW OUT connector.

OUTPUT FADE BLACK, WHITE, STILL 5 “BLACK” or “WHITE” specifies the fade color used during an output fade.

5 Setting this to “STILL” makes the [OUTPUT FADE] button function as a still-image output button.

OUTPUT FADE WHITE LEVEL 0–255 This adjusts the white level during output fade.

OUTPUT FADE BLACK LEVEL 0–255 This adjusts the black level during output fade.

OUTPUT FADE AUDIO FLW OFF, ON Setting this to “ON” enables the Audio Follow feature during output fade.

AUDIO AUTO MIXING SW OFF, ON This switches the Auto Mixing feature on or off.

AUTO MIXING SETUP ([EDIT]) This displays the AUTO MIXING Screen (p. 8).

ECHO CANCEL SW OFF, ON This switches the Echo Cancel feature on or off.

ECHO CANCEL SETUP ([EDIT]) This displays the ECHO CANCEL Screen (p. 8).

AUDIO FOLLOW SW OFF, ON This switches the Audio Follow feature on or off.

AUDIO FOLLOW SETUP ([EDIT]) This displays the AUDIO FOLLOW Screen (p. 13).

Page 3/3

USER The setting items are similar to those for “USER Button Settings” (p. 16).

MEMORY SAVE ([SETUP]) This displays the MEMORY SELECT Screen (p. 9).

LOAD ([SELECT]) This displays the MEMORY LOAD Screen (p. 9).

MANUAL MODE OFF, ON This sets whether the state of the operation panel is updated (ON) or not updated (OFF) when a memory is recalled.

POWER ON LOAD OFF, 1–8 Selecting a memory number causes the settings at the selected memory number to be recalled at startup.


5


REMOTE MIDI Rx CHANNEL 1–16 This sets the receive channel for MIDI messages when operating the VR-4HD remotely using an external MIDI device.

RS-232 OFF, ON Setting this to “ON” makes it possible to send and receive RS-232 commands.

BAUDRATE 9600, 19200, 38400, 115200 This sets the communication speed (bps) of the RS-232 connector.

GPI 1 TYPE :

GPI 4 TYPE

N/A, VIDEO CH SEL 1–4, MEMORY LOAD 1–8, USER 1–5

This sets the function assigned to the GPI channel.

N/A: No function is assigned.VIDEO CH SEL: This switches the video.MEMORY LOAD: This loads a memory.USER: This performs the same operation as pressing the USER button.* When a control signal is input from an external source, the assigned function is executed.

The GPI trigger is fixed at the trailing edge (low: ON).For details, refer to “Inputting a Control Signal” (p. 24).

GPO 1 TYPE : GPO 4 TYPE

ONE SHOT, ALT

This sets the operation mode of the GPO channel.

ONE SHOT: This outputs a control signal for 1 second.ALT: This outputs a control signal using alternate operation.

* You can output a control signal by assigning a GPO channel (1–4) to a USER button, then operating the USER button.For details, refer to “Outputting a Control Signal” (p. 25).

SYSTEM HDCP OFF, ON When set to “ON,” copyright-protected (HDCP) video can be input. HDCP is also added to the video that is output.

FRAME RATE 59.94 Hz, 50 HzThis sets the frame rate.

* For output via the USB 3.0 only, the frame rate when set to “59.94 Hz” is “29.97 Hz.” Similarly, when set to “50 Hz,” the frame rate is “25 Hz.”

SYSTEM FORMAT 720p, 1080i, 1080p

This specifies the system format for the VR-4HD. The input and output formats of the respective connectors are determined according to the system format, as shown in the table below.

System format

Input format (*2) Output format

Input connector: HDMI IN 1–3

Output connector:

PVW OUT, HDMI OUT (*3), RGB/COMPONENT (*3)

Output connector:

USB 3.0

720p 720p 720p 720p

1080i 1080i, 1080p 1080i1080p

1080p 1080i, 1080p 1080p

(*2) For the channel 4 input connectors (HDMI IN 4, RGB/COMPONENT 4, and COMPOSITE 4), you set the input format individually using “RESOLUTION (EDID)” (p. 2), irrespective of the system format.

(*3) For the HDMI OUT connector and the RGB/COMPONENT output connector, you can specify a desired output format by using “OUTPUT RESOLUTION” (p. 4).The system format setting is followed only when “OUTPUT RESOLUTION” is set to “AUTO.”

AUTO SWITCHING OFF, ON This turns the auto switching function on/off. If this is “ON,” the video of channels 1–4 switches automatically.

AUTO SW TRANSITION TIME 0.0–4.0secThis specifies the video switching time.

* If auto switching is “ON,” video switching uses the time you specify here, not the setting of the [TIME] knob.

AUTO SWITCHING TYPEAUTO SCAN, BEAT SYNC SWITCHING, VIDEO FOLLOWS AUDIO

This specifies the type of auto switching. The available parameters change according to the selected type.

AUTO SCAN Automatically switch the video of channels 1–4.

SCAN TIME VIDEO INPUT1 OFF, 1–5–120sec

This specifies the AUTO SCAN switching time for each video channel.




SEQUENCE

This specifies the order in which video is displayed.

NORMAL Switches in the order of channels 1–4.

RANDOM Switches randomly.


6


SYSTEM BEAT SYNC SWITCHING This switches the video of channels 1–4 in synchronization with the beat of the corresponding audio.

SYNC SOURCEIN1, IN2, IN3, IN4, IN5/6, IN7/8, HDMI1, HDMI2, HDMI 3, HDMI4, USB FROM PC

This specifies the input audio to which the video is synchronized.

CYCLE 1–4–16 This specifies the number of beats before switching to the next video.

SEQUENCE

This specifies the order in which video is displayed.

NORMAL Switches in the order of channels 1–4.

RANDOM Switches randomly.

VIDEO INPUT1 SW OFF, ON

These specify whether the input is (ON) or is not (OFF) affected the video switching.VIDEO INPUT2 SW OFF, ON



VIDEO FOLLOWS AUDIO The channel 1–4 video is switched according to the volume that is input to an AUDIO INPUT.

TIME 1–2–120sec This specifies the time from when mic audio is detected and the video/scene is switched until audio detection resumes.

INPUT1 SENSE 0–50–100

This specifies the detection level of the audio that is input from each AUDIO INPUT connector. The higher the level, the easier it is to detect audio.




INPUT1 SELECT OFF, 1, 2, 3, 4, QUAD This specifies the video that is output when audio is detected at AUDIO INPUT 1.




MULTI INPUT SELECT OFF, 1, 2, 3, 4, QUAD This specifies the video that is output when audio is detected at multiple inputs of AUDIO INPUT 1–4.

SILENT SELECT OFF, 1, 2, 3, 4, QUAD, AUTO SCAN This specifies the video that is output when no audio input is present at any input connector.

LCD BRIGHTNESS LOW, HIGH This sets the brightness of the built-in monitor.

MENU DISPLAY LEVEL 5–13–15 This adjusts the brightness of the menu display.

LEVEL METER DISPLAY OFF, ON Setting this to “ON” displays a volume level meter on the built-in monitor.

INPUT CH LEVEL DISPLAY OFF, ON Setting this to “ON” displays labels identifying the input signals on the built-in monitor.

TALLY LABEL DISPLAY OFF, ON Setting this to “ON” displays a tally border on the built-in monitor and in preview output.

NO SIGNAL BACK BLACK, BLUE This sets the background color of channels that have no video input.

UNFIT SIGNAL BACK BLACK, BLUE, THRU

This sets the background color of channels on which video of an incompatible format is input.

When set to “THRU,” video in an unsupported format is output unchanged, allowing confirmation of the status of the input signal. Note, however, that the video might contain additional noise artifacts.

DEINTERLACE MODE WEAVE, BOB

This specifies the method used when converting interlaced input video to progressive video.

WEAVE: This joins the top field and bottom field in a single frame. This is optimal for video that contains little movement.

BOB: This interpolates the top field and bottom field, and unites them in a single frame. This is optimal for video that contains much movement.

COLOR BAR OUTPUT OFF, ON Setting this to “ON,” a color bar is output.

TEST TONE OUTPUT OFF, ON Setting this to “ON” outputs a test tone.

AUTO OFF OFF, ON This sets the Auto Off function on or off. When set to “ON,” the power to the VR-4HD is automatically turned off if 240 minutes elapse with no operation performed on the unit.


7


SYSTEM PANEL LOCK This sets whether panel lock is enabled (ON) or disabled (OFF) for all controllers except the [SYSTEM SETUP] button and the [VALUE] knob.

ALL

OFF, ON

Locks all lockable controllers.

VIDEO INPUT CH1–4 BUTTON Individually locks the VIDEO INPUT SELECT [1]–[4] buttons.

OUTPUT FADE BUTTON Locks the [OUTPUT FADE] button.

KEY BUTTON Locks the [KEY] button.

IN/OUT SETUP BUTTON Locks the [IN/OUT SETUP] button.

MONITOR/PVW BUTTON Locks the [INPUT][OUTPUT] button.

VFX/KEY LEVEL BUTTON Locks the [VIDEO FX/KEY LEVEL] button.

FREEZE BUTTON Locks the [FREEZE] button.

PinP BUTTON Locks the [PinP] button.

SPLIT BUTTON Locks the [SPLIT] button.

QUAD BUTTON Locks the [QUAD] button.

CUT BUTTON Locks the [CUT] button.

MIX BUTTON Locks the [MIX] button.

WIPE BUTTON Locks the [WIPE] button.

TRANSITION TIME KNOB Locks the [TIME] knob.

USER1–5 BUTTON Locks the USER [1]–[5] buttons.

USER SETUP BUTTON Locks the USER[SETUP] button.

HDMI1–4 LEVEL KNOB Individually locks the HDMI [1]–[4] knobs.

HDMI SETUP BUTTON Locks the HDMI[SETUP] button.

USB FROM PC KNOB Locks the [FROM PC] button.

USB TO PC KNOB Locks the [TO PC] button.

USB SETUP BUTTON Locks the USB[SETUP] button.

INPUT1–4 GAIN KNOB Individually locks the INPUT1–4 [GAIN] knobs.

INPUT1–4 LEVEL FADER Individually locks the INPUT 1–4 channel faders.

INPUT1–4 SETUP BUTTON Individually locks the INPUT 1–4 [SETUP] buttons.

INPUT5/6 LEVEL FADER Locks the INPUT 5/6 channel fader.

INPUT5/6 SETUP BUTTON Locks the INPUT 5/6 [SETUP] button.

INPUT7/8 LEVEL FADER Locks the INPUT 7/8 channel fader.

INPUT7/8 SETUP BUTTON Locks the INPUT 7/8 [SETUP] button.

MAIN OUT LEVEL FADER Locks the [MAIN] fader.

MAIN OUT SETUP BUTTON Locks the MAIN [SETUP] button.

PHONES KNOB Locks the [PHONES] knob.

REVERB KNOB Locks the [REVERB] knob.

TOUCH PANEL Locks tap operations on the unit’s own monitor.

FREEZE MODE ALL, SELECT This sets the operation mode for freezes.

TOUCH PANEL CALIBRATION ([EXEC]) This calibrates the tap points for the touch panel (the built-in monitor).

FACTORY RESET ([EXEC]) This returns the unit to its factory defaults.

VERSION — This displays the version of the system program.


8

AUTO MIXING Screen

1

2

3

No. Setting item Value Explanation

1 Auto Mixing switch OFF, ON This switches the Auto Mixing feature on or off.

2 Channel switches

HDMI1–4 OFF, ON

This specifies whether Auto Mixing is applied (ON) or not applied (OFF).CH1–4 OFF, ON

CH5/6, 7/8 OFF, ON

3 Weight level 0–100 This sets the priority for volume-level distribution.

ECHO CANCEL Screen

Setting item Value Explanation

Echo Cancel switch OFF, ON This switches the Echo Cancel feature on or off.

CH1–4 DEPTH 1–5–10 This sets the effect intensity of Echo Cancel.

CH1–4 SW OFF, ON This specifies whether Echo Cancel is applied (ON) or not applied (OFF).


9

MEMORY SELECT Screen


MEMORY1–8 — These select the memory to work with.

INIT — This returns the content of the selected memory to its factory-default state.

RENAME — This displays the RENAME MEMORY screen .This changes the name of the selected memory.

SAVE —

This saves the current settings to the selected memory.

* The state of the [OUTPUT FADE] button on the operation panel is not saved in memory. Also, the following system settings (p. 2) are not saved to memory. Only a single set is saved in the unit.

Category Setting items saved in the unit

SYSTEMAll setting items except “COLOR BAR OUTPUT” and “TEST TONE OUTPUT”

* “COLOR BAR OUTPUT” and “TEST TONE OUTPUT” are always set to “OFF” at startup.

REMOTEAll setting items

MEMORY

MEMORY LOAD Screen


MEMORY1–8 — These load the selected memory.


10

Audio Channel 1–4 Settings (Audio Channel 1–4 [SETUP] buttons)


SOLO OFF, ON (blue) This sets the Solo feature on or off. Only the input audio for the channel which has solo “ON” can be monitored via headphones.

MUTE OFF, ON (red) This sets the Mute feature on or off. Input audio for which this is set to “ON” is silenced.

HA GAIN 0–64 dB This adjusts head amp gain.

GAIN -42.0–0.0–42.0 dB This adjusts digital gain.

LEVEL -Inf–10.0 dB This adjusts the volume level of input audio.

AUX SEND -Inf–0.0–10.0 dB This adjusts the send level of audio to the AUX bus.

REV SEND -Inf–10.0 dB This adjusts the send level of audio to Reverb.

EQ HI -15–0–15 dB This boosts or attenuates the high band.

FREQ 1.00–10.0–20.0 KHz This adjusts the center frequency when changing the sound quality in the high band.

EQ MID -15–0–15 dB This boosts or attenuates the middle band.

FREQ 20.0 Hz–500 Hz–20.0 KHz This adjusts the center frequency when changing the sound quality in the middle band.

Q 0.5–1.0–16.0 This adjusts the width of the frequency band when boosting or attenuating the middle band.

EQ LO -15–0–15 dB This boosts or attenuates the low band.

FREQ 20.0–100–500 Hz This adjusts the center frequency when changing the sound quality in the low band.

GATE OFF, ON This sets gate on or off.

THRESHOLD -80– -50–0 dB This sets the level used as the threshold for removing audio. Audio below the level set here is removed.

RELEASE 30–860–5000 ms This adjusts the length of time until the audio is fully attenuated after audio falls below the threshold.

COMP OFF, ON This sets the compressor on or off.

THRESHOLD -60– -30–0 dB This sets the level used as the threshold at which the compressor is applied. Compression is applied to audio that exceeds the level set here.

RATIO1.00: 1, 1.12: 1, 1.25: 1, 1.40: 1, 1.60: 1, 1.80: 1, 2.00: 1, 2.50: 1, 3.20: 1, 4.00: 1, 5.60: 1, 8.00: 1, 16.0: 1, INF: 1

This specifies the degree of compression applied to the audio. The state in which no compression is applied is defined as “1.”

ATTACK 0.2–1–100 ms This sets the time until compression starts when audio exceeding the threshold is input.

RELEASE 30–380–5000 ms This adjusts the length of time until compression ends after audio falls below the threshold.

AUTO GAIN OFF, ON

This switches the auto makeup gain feature on or off.

When this is set to “ON,” the final output volume level after applying the compressor is automatically adjusted according to the “THRESHOLD” and “RATIO” settings. The total of the “MAKEUP GAIN” setting value described below and the value calculated by auto makeup gain becomes the final output volume level (up to +34 dB).

MAKEUP GAIN -40–0–40 dB This adjusts the final output volume level after applying the compressor.

HPF OFF, ON This sets the high-pass filter on or off.

PAN LEFT–CENTER–RIGHT This adjusts the sound position (pan).

DELAY 0.0–500.0 ms This adjusts the delay time for audio.


11

Audio Channel 5/6 and 7/8 Settings (Audio Channel 5/6 and 7/8 [SETUP] buttons)



MUTE OFF, ON (red) This sets the Mute feature on or off. Input audio for which this is set to “ON” is silenced.


LEVEL -Inf–10.0 dB This adjusts the volume level of input audio.












12

Settings for Main Output Audio (MAIN [SETUP] button)


AUX MUTE OFF, ON (red) This sets the Mute feature for the AUX bus on or off. Setting this to “ON” mutes out audio output from the AUX bus.

MAIN MUTE OFF, ON (red) This sets the Mute feature for the MAIN bus on or off. Setting this to “ON” mutes out the main output audio.

MAIN LEVEL -Inf–10.0 dB This adjusts the volume level of the main output audio

AUX LEVEL -Inf–10.0 dB This adjusts the volume level of audio output from the AUX bus.

PHONES LVL -Inf–10.0 dB This adjusts the volume level for headphones.

MAIN LIMITER OFF, ON This sets the limiter for main output audio on or off.

THRESHOLD -40–-6–0 dB This sets the level that becomes the threshold at which the limiter is applied. Compression is applied to audio that exceeds the threshold. The volume level of audio that is output is limited so as to stay to below the threshold.

PHONES LIMITER OFF, ON This sets the limiter for headphones output audio on or off.

THRESHOLD -40–-6–0 dB This sets the level that becomes the threshold at which the limiter is applied. Compression is applied to audio that exceeds the threshold. The volume level of audio that is output is limited so as to stay to below the threshold.








REVERB -Inf–10.0 dB This adjusts the return level from reverb of the audio.

TIME 0.0–1.5–5.0 s This adjusts the length of the reverb.

TYPE Room, HallThis specifies the type of reverb.

Room: Produces the natural reverberations of a highly resonant room.Hall: Produces reverberations like that of a performance in a concert hall or other such space.

MB COMP OFF, ON This sets multi-band compressor on or off.

HI THRES -40– -20–0 dBThese set the individual levels that become the thresholds for the high, midrange, and low bands at which the compressor is applied. Compression is applied to audio that exceeds the threshold.MID THRES -40– -16–0 dB

LO THRES -40– -20–0 dB

HI RATIO 1.00: 1, 1.12: 1, 1.25: 1, 1.40: 1, 1.60: 1, 1.80: 1, 2.00: 1, 2.50: 1, 3.20: 1, 4.00: 1, 5.60: 1, 8.00: 1, 16.0: 1, INF: 1

* The default value for “MID RATIO” is “2.50:1.”

These set the amount of compression applied in the high, midrange, and low bands. The state in which no compression is applied is defined as “1.”MID RATIO

LO RATIO

AUX DELAY 0.0–500.0 ms This adjusts the delay time for audio output from the AUX bus.

BUS SELECT — This displays the BUS SELECT Screen (p. 13).

AUDIO FOLLOW — This displays the AUDIO FOLLOW Screen (p. 13).

SOLO CLEAR — This turns off all Solo settings at once.

MUTE CLEAR — This turns off all Mute settings at once.


13

BUS SELECT Screen


MAIN MAIN, AUX

These set the audio bus (MAIN bus or AUX bus) assigned to the respective connector.AUX MAIN, AUX

PHONES MAIN, AUX

USB MAIN, AUX

AUDIO FOLLOW Screen


Audio Follow switch OFF, ON This sets the Audio Follow feature on or off.

(Matrix chart) OFF, ON This sets the input audio to use with Audio Follow for each video channel. When set to “ON,” Audio Follow is applied.


14

HDMI Audio Channel 1– 4 Settings (HDMI [SETUP] button g < > < > )



MUTE OFF, ON (red) This sets the Mute feature on or off. HDMI audio for which this is set to “ON” is silenced.


LEVEL -Inf–10.0 dB This adjusts the volume level of HDMI audio.












15

USB Input/Output Audio Settings (USB [SETUP] button g < > < > )

USB FROM PC



MUTE OFF, ON (red) This sets the Mute feature on or off. USB input audio for which this is set to “ON” is silenced.


LEVEL -Inf–10.0 dB This adjusts the volume level of USB input audio.











CONNECTION — If a USB connection with the computer fails to be established or video is corrupt, select < RESET> to reconnect via USB.

STATUS — This indicates a connection using either USB 2.0 or USB 3.0. When no connection to a computer has been made, the message “NC” is displayed.

DROPPED — This is normally “0.” An increase in this value means that video transmission is not fast enough.

USB TO PC


MUTE OFF, ON (red) This sets the Mute feature on or off. USB output audio for which this is set to “ON” is silenced.

LEVEL -Inf–10.0 dB This adjusts the volume level of USB output audio.


CONNECTION — If a USB connection with the computer fails to be established or video is corrupt, select < RESET> to reconnect via USB.

STATUS — This indicates a connection using either USB 2.0 or USB 3.0. When no connection to a computer has been made, the message “NC” is displayed.

DROPPED — This is normally “0.” An increase in this value means that video transmission is not fast enough.


16

USER Button Settings (USER [SETUP] button g <ASSIGN>)


USER1 ASSIGN

NONE, ECHO CANCEL SW, AUTO MIXING SW, AUDIO FLW SW, AUTO SWITCHING SW MEMORY SELECT, MEMORY LOAD, MUTE SELECT, MUTE GROUP, SOLO SELECT, SOLO GROUP, GPO, CH4 INPUT CAPTURE

* The default values are as follows.

USER1: AUTO SWITCHING SW

USER2: ECHO CANCEL SW

USER3: SOLO SELECT

USER4: MUTE SELECT

USER5: MEMORY SELECT

This sets the functions assigned to the USER [1]– [5] buttons.

NONE: No function is assigned.

ECHO CANCEL SW: This switches the Echo Cancel feature on or off.

AUTO MIXING SW: This switches the Auto Mixing feature on or off.

AUDIO FLW SW: This switches the Audio Follow feature on or off.

AUTO SWITCHING SW: This switches the Auto Switching feature on or off.

MEMORY SELECT: This displays the MEMORY LOAD Screen (p. 9). This lets you select and call up a memory.

MEMORY LOAD: This calls up a saved memory.

MUTE SELECT: This displays the MUTE SELECT Screen (p. 17). This lets you specify whether the Mute feature is on (red) or off for each individual audio input and output.

MUTE GROUP: This switches the Mute feature on or off globally for all audio assigned to a group.

SOLO SELECT: This displays the SOLO SELECT Screen (p. 17). This lets you specify whether the Solo feature is on (blue) or off for each individual audio input.

SOLO GROUP: This switches the Solo feature on or off globally for all audio assigned to a group.

GPO: This outputs a control signal from the TALLY/GPIO connector. The USER button lights up during output of the control signal.

CH4 INPUT CAPTURE: This captures the video of input CH4 (p. 2).

USER2 ASSIGN

USER3 ASSIGN

USER4 ASSIGN

USER5 ASSIGN

USER1 LED COLOR RED, GREEN, BLUE, CYAN, MAGENTA, YELLOW

* The default values are as follows.

USER1: MAGENTA

USER2: YELLOW

USER3: BLUE

USER4: RED

USER5: CYAN

This sets the colors of the USER [1]–[5] buttons when they light up.

USER2 LED COLOR

USER3 LED COLOR

USER4 LED COLOR

USER5 LED COLOR


17

MUTE SELECT Screen


CH 1–4, CH5/6, CH7/8, USB FROM PC, HDMI 1–4, USB TO PC, AUX, MAIN

OFF, ON (red) This specifies whether the Mute feature is on (red) or off for each individual audio input and output.

SOLO SELECT Screen


CH 1–4, CH5/6, CH7/8, USB FROM PC, HDMI 1–4 OFF, ON (blue) This specifies whether the Solo feature is on (blue) or off for each individual audio input.


18

USER Button Advanced Settings (USER [SETUP] button g <USER1> – <USER5> )

Here you make advanced settings for functions assigned to the USER [1] through [5] buttons. The currently assigned functions are displayed at the buttons at the bottom of the screen.

USER1–5 ASSIGN settings USER1–USER5 SETUP Screen Page USER1–5 ASSIGN settings USER1–USER5 SETUP Screen Page

NONE — — MEMORY LOAD MEMORY LOAD SW Screen p. 18

ECHO CANCEL SW ECHO CANCEL Screen p. 8 MUTE SELECT — —

AUTO MIXING SW AUTO MIXING Screen p. 8 MUTE GROUP MUTE GROUP Screen p. 19

AUDIO FLW SW AUDIO FOLLOW Screen p. 13 SOLO SELECT — —

AUTO SWITCHING SW AUTO SWITCHING Screen p. 18 SOLO GROUP SOLO GROUP Screen p. 19

MEMORY SELECT MEMORY SELECT Screen p. 9 GPO GPO Screen p. 19

AUTO SWITCHING Screen


AUTO SWITCHING SW OFF, ONTurns the auto switching function on/off.

* This is the same setting as “AUTO SWITCHING” (p. 5).

TRANSITION TIME 0.0–4.0secSpecifies the display interval when the auto switching function is on.

* This is the same setting as “AUTO SW TRANSITION TIME” (p. 5).

TYPEAUTO SCAN, BEAT SYNC SWITCHING, VIDEO FOLLOWS AUDIO

Specifies the type of auto switching. The available parameters change according to the selected type (p. 5).

MEMORY LOAD SW Screen


MEMORY1–8 MEMORY1, MEMORY2–8 The memory you want to call up is saved when you press a USER button. The button it is saved to lights up in red.


19

MUTE GROUP Screen


CH 1–4, CH5/6, CH7/8, USB FROM PC, HDMI 1–4, USB TO PC, AUX, MAIN

— When you press the USER button, the input/output audio for which the Mute feature is to be switched on are selected and assigned to a group. The button it is assigned to lights up in red.

SOLO GROUP Screen


CH 1–4, CH5/6, CH7/8, USB FROM PC, HDMI 1–4 — When you press the USER button, the input audio and output audio for which the Solo feature is to be switched on are selected and assigned to a group. The button it is assigned to lights up in blue.

GPO Screen


CHANNEL 1–4 This sets the GPO channel (1–4) on which the control signal is output.

GPO 1 TYPE : GPO 4 TYPE

ONE SHOT, ALT

This sets the operation mode of the GPO channel.

ONE SHOT: This outputs a control signal for 1 second.ALT: This outputs a control signal using alternate operation.

* These are identical to the settings for “GPO 1 TYPE”–”GPO 4 TYPE” (p. 5).


20

Settings for Assignments to Video Input/Output Connectors ([IN/OUT SETUP] button)


INPUT CH1–3 — This displays the input format of video channel 1–3.

CH4 HDMI, RGB, COMPOSITEThis specifies the video source to input on video channel 4.

* This is identical to the setting for “INPUT ASSIGN” (p. 2).

OUTPUT MAIN — This displays the output format of the HDMI OUT connector and the RGB/COMPONENT output connector.

PVW , (Default value)This specifies the video to output via the PVW OUT connector (PVW) and the USB 3.0 port (USB).

: The main output video is output.

: The incoming video on channels 1 through 4 is output as a fourway split screen.

* The setting for “PVW” is interlinked with the selection of the [INPUT] and [OUTPUT] buttons.USB (Default value),

21

RS-232 Command ReferenceUsing the RS-232 connector, you can operate the VR-4HD remotely from an external device.

Specification of the RS-232 Connector

1 2 3 4 5

6 7 8 9

D-sub 9-pin (male)

Pin No. Signal

1 N.C.

2 RXD

3 TXD

4 DTR

5 GND

6 DSR

7 RTS

8 CTS

9 N.C.

Communication method Synchronous (asynchronous), full-duplex

Communication speed (bps) 9600, 19200, 38400, 115200

Parity none

Data length 8 bit

Stop bit 1 bit

Code set ASCII

Flow control XON/XOFF

Cable Wiring DiagramWire the three lines of RXD, TXD, and GND as shown in the figure below.

VR-4HD Controller

N.C.: 1 1:

RXD: 2 2: RXD

TXD: 3 3: TXD

DTR: 4 4:

GND: 5 5: GND

DSR: 6 6:

RTS: 7 7:

CTS: 8 8:

N.C.: 9 9:

* The connections between 4 and 6 and between 7 and 8 are inside the VR-4HD.

* When connecting to a controlling device (such as an RS-232 compatible computer), use a crossover cable.

Overview of CommandsCommands are each formatted as an ASCII code string composed of “stx” plus “three alphabetic letters (capitals)” plus “;” (semicolon).

The three letters of the alphabet indicate the type of command.

If the command has an argument, a colon (“:”) is inserted between the command letters and the argument. When multiple arguments occur, they are separated by commas (“,”).

stx An ASCII-code signal name (code number: 02H), this is a control code indicating the start of a command. “H” indicates that it is a hexadecimal value.

: This is the code that the VR-4HD recognizes as a separator between a command and its argument.

; This is the code that the VR-4HD recognizes as the end of a command.

* The codes of stx (02H), ACK (06H), and Xon (11H)/ Xoff (13H) are the control codes.

* When successively sending commands to the VR-4HD from an external device, after each command, be sure that “ACK” is returned before sending the next command.

RS-232 Command Reference

22

Received Commands (Controller g VR-4HD)Item Received Commands Parameter

Select video input channel stxPGM:a; a: 0 (CH 1)–3 (CH 4)

Set input connector for INPUT 4 stxIS4:a; a: 0 (HDMI), 1 (RGB), 2 (CVBS)

Specify transition effect stxTRS:a; a: 0 (CUT), 1 (MIX), 2 (WIPE)

Set transition time stxTIM:a; a: 0 (0.0 sec)– 40 (4.0 sec)

Set PinP on/off stxPIP:a; a: 0 (OFF), 1 (ON)

Select video input channel for PinP inset screen stxPIS:a; a: 0 (CH 1)–3 (CH 4)

Set key compositing on/off stxDSK:a; a: 0 (OFF), 1 (ON)

Select source channel for key compositing stxDSS:a; a: -1 (OFF), 0 (CH 1)–3 (CH 4)

Set output fade on/off stxFDE:a; a: 0 (OFF), 1 (ON)

Set freeze on/off stxFRZ:a; a: 0 (OFF), 1 (ON)

Adjust audio channel 1 input level stxLM1:a; a: 0–127




Adjust audio channel 5/6 input level stxLS1:a; a: 0–127

Adjust audio channel 7/8 input level stxLS2:a; a: 0–127

Adjust HDMI 1 input level stxLH1:a; a: 0–127




Adjust input level from USB stxLUB:a; a: 0–127

Adjust level of main output audio stxLMN:a; a: 0–127

Load memory stxMEM:a; a: 0 (MEMORY 1)–7 (MEMORY 8)

Reset USB connection stxRUB;

Return version information stxVER;

Return PinP status stxQPI;

Return key compositing status stxQDK;

Return selected video input channel stxQPG;

Return USB connection status stxQUB;

Flow control XON

Flow control XOFF

RS-232 Command Reference

23

Sent Commands (VR-4HD g Controller)Item Sent Commands Parameter

Sent when a transmitted command has been correctly received

* When a VER, QPI, QDK, QPG, QUB, XON, or XOFF command is received, no ACK is sent.

ACK

Sent when a transmitted command has not been correctly received stxERR:a; a: 0 (syntax error) The received command contains an error.

4 (invalid value error) An argument of the received command is invalid.

5 (out of range error) An argument of the received command is out of range.

Sent when a VER command has been received stxVER:VR-4HD,a; a: Version * The version info is ASCII text strings.

PinP status is sent at the following times

• When PinP status has changed

• When a QPI command is received

stxQPI:a,b; a: 0 (OFF), 1 (ON)

b: 0 (CH 1)–3 (CH 4) Selected channel for PinP inset screen

Key compositing status is sent at the following times

• When key compositing status has changed

• When a QDK command is received

stxQDK:a,b; a: 0 (OFF), 1 (ON)

b: -1 (OFF), 0 (CH 1)–3 (CH 4) Source channel for key compositing

The selected video input channel is sent at the following times

• When the selected video input channel has changed

• When a QPG command is received

stxQPG:a; a: 0 (CH 1)–3 (CH 4)

USB connection status is sent at the following times

• When USB connection status has changed

• When a QUB command is received

stxQUB:a; a: 0 (unconnected), 2 (USB 2.0), 3 (USB 3.0)

Flow control XON

Flow control XOFF

24

Control Using the TALLY/GPIO ConnectorYou can operate the VR-4HD remotely from an external device by inputting a GPI control signal via the TALLY/GPIO connector.

You can also output a tally signal and a GPO control signal from the TALLY/GPIO connector

Specification of the TALLY/GPIO Connector

Mini D-sub 15-pin (female)

5 4 3 2 1

15 14 13 12 11

10 9 8 7 6

Pin No. Function Tally/control output

Trigger method Open collector

Maximum input 12 V/200 mA

Control input

Trigger method No-voltage contact (make-contact) triggering

Contact capacity DC 24 V 0.1 A or higher

Input method Photocoupler

1 TALLY PGM 1

2 GPO 1

3 GPI 1

4 GND

5 TALLY PGM 4

6 TALLY PGM 2

7 GPO 2

8 GPI 2

9 GND

10 GPO 4

11 TALLY PGM 3

12 GPO 3

13 GPI 3

14 GND

15 GPI 4

Inputting a Control SignalTo operate the VR-4HD remotely using control-signal input, you first assign the function to a GPI channel (1 through 4).

1. Press the [SYSTEM SETUP] button to display the setup screen.

2. Select <REMOTE> to display the REMOTE menu.

3. Select the target from among <GPI 1 TYPE> through <GPI 4 TYPE>.

4. Use the [VALUE] knob to specify the function to assign to the GPI channel (1 through 4).

Value Explanation

N/A No function is assigned.

VIDEO CH SEL 1–4 This switches the video.

MEMORY LOAD 1–8 This loads a memory.

USER 1–5 This performs the same operation as pressing the USER button.

5. Press the [SYSTEM SETUP] button several times to quit the setup screen.When a control signal is input from an external source, the assigned function is executed. The GPI trigger is fixed at the trailing edge (low: ON).

Outputting a Tally SignalA tally signal is output from the connector pin corresponding to the video channel being output, also including video composition and transition effects.

* The tally-signal output is for the main output video.

Control Using the TALLY/GPIO Connector

25

Outputting a Control SignalYou can output a control signal by assigning a GPO channel (1 through 4) to a USER button, then operating the USER button.

1. Press the USER [SETUP] button to display the setup screen.

2. Select <ASSIGN> to display the ASSIGN menu.

3. Select the target from among <USER 1 ASSIGN> through <USER5 ASSIGN>, then use the [VALUE] knob to specify “GPO” as the function to assign to the USER button.

4. Go to the bottom of the screen and select <BACK> to go back to the previous screen.

5. Select where the GPO function is assigned (<USER 1> through <USER 5>) to display the USER1 through 5 SETUP: GPO screen.The currently assigned functions are displayed at the buttons at the bottom of the screen.

6. Select <CHANNEL>, then use the [VALUE] knob to set the GPO channel (1 through 4) for outputting the control signal.

7. Select one from among <GPO 1 TYPE> through <GPO 4 TYPE>, then use the [VALUE] knob to specify the operation mode of the GPO channel.

Value Explanation

ONE SHOT This outputs a control signal for 1 second.

ALT This outputs a control signal using alternate operation.

8. Press the USER [SETUP] button several times to quit the setup screen.Operating the USER button where the GPO function is assigned outputs a control signal from the corresponding GPO pin. The USER button lights up during output of the control signal.

26

MIDI ImplementationModel: VR-4HDDate: March 16. 2017Version: 1.50

Symbol Item Setting Range

n MIDI Channel 0H–FH (VR-4HD system settings)

1. MIDI Messages Received at MIDI IN��Channel Voice Messages

* Set the receiving channel of VR-4HD according to the master device channel by pressing the [SYSTEM SETUP] button g <REMOTE> g <MIDI Rx CHANNEL>.

�z Control Change�{ Undefined (Controller Number 21–30, 52–54)

Status 2nd Byte 3rd ByteBnH ccH vvH

* These control the value of fader/knob level.

cc= Control Change Number: 00H–7FH (See the correspondence table below.)

cc Corresponding fader/knob cc Corresponding fader/knob

15H CH [1] fader 1CH HDMI [2] knob

16H CH [2] fader 1DH HDMI [3] knob

17H CH [3] fader 1EH HDMI [4] knob

18H CH [4] fader 1FH USB [FROM PC] knob

19H CH [5/6] fader 34H [MAIN] fader

1AH CH [7/8] fader 35H [AUX] fader

1BH HDMI [1] knob 36H USB [To PC] knob

vv= Control Value: 00H-7FH (0-127) The following table shows how fader values correspond to control values (unit: dB).

0 -Inf 32 -33.1 64 -11.3 96 -0.3

1 -80.0 33 -32.3 65 -10.7 97 0.02 -76.7 34 -31.5 66 -10.3 98 0.33 -73.3 35 -30.8 67 -10.0 99 0.74 -70.0 36 -30.0 68 -9.7 100 1.05 -66.7 37 -29.3 69 -9.3 101 1.36 -63.3 38 -28.7 70 -9.0 102 1.77 -60.0 39 -28.0 71 -8.7 103 2.08 -58.6 40 -27.3 72 -8.3 104 2.39 -57.1 41 -26.7 73 -8.0 105 2.710 -55.7 42 -26.0 74 -7.7 106 3.011 -54.3 43 -25.3 75 -7.3 107 3.312 -52.9 44 -24.7 76 -7.0 108 3.713 -51.4 45 -24.0 77 -6.7 109 4.014 -50.0 46 -23.3 78 -6.3 110 4.315 -48.9 47 -22.7 79 -6.0 111 4.716 -47.8 48 -22.0 80 -5.7 112 5.017 -46.7 49 -21.3 81 -5.3 113 5.318 -45.6 50 -20.7 82 -5.0 114 5.719 -44.4 51 -20.0 83 -4.7 115 6.020 -43.3 52 -19.3 84 -4.3 116 6.321 -42.2 53 -18.7 85 -4.0 117 6.722 -41.1 54 -18.0 86 -3.7 118 7.023 -40.0 55 -17.3 87 -3.3 119 7.324 -39.2 56 -16.7 88 -3.0 120 7.725 -38.5 57 -16.0 89 -2.7 121 8.026 -37.7 58 -15.3 90 -2.3 122 8.327 -36.9 59 -14.7 91 -2.0 123 8.728 -36.2 60 -14.0 92 -1.7 124 9.029 -35.4 61 -13.3 93 -1.3 125 9.330 -34.6 62 -12.7 94 -1.0 126 9.731 -33.8 63 -12.0 95 -0.7 127 10.0

�{ Undefined (Controller Number 14)Status 2nd Byte 3rd ByteBnH 0EH vvH

vv: 00H–03H (CH 1–4)

* This selects the video output.

�{ Undefined (Controller Number 15)Status 2nd Byte 3rd ByteBnH 0FH vvH

vv: 00H–03H (CH 1–4)

* This selects the video for composition.


vv: 00H–02H (CUP, MIX, WIPE)

* This selects the type of video transition effect.


vv: 00H–28H (0.0–4.0 sec)

* This controls the value of video transition time.

�{ Undefined (Controller Number 55)Status 2nd Byte 3rd ByteBnH 37H vvH

vv: 00H–01H (OFF, ON)

* This turns the [KEY] button on/off.


vv: 00H–04H (OFF, CH 1–4)

* This selects the channel for key composition.


vv: 00H–7FH (0–127)• The received value is doubled and the value of the setting on the unit is

updated.

* This sets the key-compositing level of the currently selected KEY TYPE.

�{ Undefined (Controller Number 58)Status 2nd Byte 3rd ByteBnH 3AH vvH

vv: 00H–7FH (0–127)

* This controls the value of the video effect level.

MIDI Implementation

27

�{ Undefined (Controller Number 59)Status 2nd Byte 3rd ByteBnH 3BH vvH

vv: 00H–03H (OFF, PinP, SPLIT, QUAD)

* This selects the type of video composition effect.

�{ Undefined (Controller Number 60)Status 2nd Byte 3rd ByteBnH 3CH vvH


* This turns the [OUTPUT FADE] button on/off.

�{ Undefined (Controller Number 61)Status 2nd Byte 3rd ByteBnH 3DH vvH


* This turns the [FREEZE] button on/off.

��System Exclusive MessagesStatus Data Byte StatusF0H iiH,ddH,...,eeH F7H

F0H: Status of system exclusive messageii= ID number: This is the ID to recognize manufacturer of the exclusive

message (manufacturer ID). The manufacturer ID of Roland is 41H. The ID numbers of 7EH and 7FH are expansion of MIDI standards and used as universal non-realtime message (7EH) of universal realtime message (7FH).

dd,...,ee= data: 00H–7FH (0–127)F7H: EOX (end of exclusive)

�z Data Request 1 (RQ1)This is the message to request of “send data” to the connected device. Specify data type and amount using address and size. When this is received, the unit sends the requested data as “Data Set 1 (DT1)” message in case the unit is in status where the sending of data is possible and requested address and size are appropriate. If not, the unit sends nothing.

Status Data Byte StatusF0H 41H, 10H, 00H, 00H, 00H, 29H, 11H, aaH, F7H bbH, ccH, ssH, ttH, uuH, sum

Byte ExplanationF0H Exclusive Status41H Manufacturer ID (Roland)10H Device ID00H 1st byte of model ID (VR-4HD)00H 2nd byte of model ID (VR-4HD)00H 3rd byte of model ID (VR-4HD)29H 4th byte of model ID (VR-4HD)11H Command ID (RQ1)aaH Address upper bytebbH Address middle byteccH Address lower bytessH Size upper bytettH Size middle byteuuH Size lower bytesum ChecksumF7H EOX (end of exclusive)

* Depending on the data type, the amount of single-time transmission is specified. It is necessary to execute data request according to the specified first address and size. Refer to the “3. Parameter Address Map” (p. 30) for address and size.

* See “Example of an Exclusive Message and Calculating a Checksum” (p. 40) for checksum.

�z Data Set 1 (DT1)This is the message of actual data transmission. Use this when you want to set data to the unit.

Status Data Byte StatusF0H 41H, 10H, 00H, 00H, 00H, 29H, 12H, aaH, F7H bbH, ccH, ddH, ..., eeH, sum

Byte ExplanationF0H Exclusive Status41H Manufacturer ID (Roland)10H Device ID00H 1st byte of model ID (VR-4HD)00H 2nd byte of model ID (VR-4HD)00H 3rd byte of model ID (VR-4HD)29H 4th byte of model ID (VR-4HD)12H Command ID (DT1)aaH Address upper bytebbH Address middle byteccH Address lower byteddH Data: actual data to transmit. Multiple byte data is sent in address order. : :eeH Datasum ChecksumF7H EOX (end of exclusive)

* Depending on the data type, the amount of single-time transmission is specified. It is necessary to execute data request according to the specified first address and size. Refer to the “3. Parameter Address Map” (p. 30) for address and size.

* See “Example of an Exclusive Message and Calculating a Checksum” (p. 40) for checksum.

* Data exceeding 256 bytes should be divided into packets of 256 bytes or smaller. If you send data set 1 successively, set interval of 20 ms or longer between packets.

MIDI Implementation

28

2. MIDI Messages Transmitted from MIDI OUT��Channel Voice Messages

�z Control Change�{ Undefined (Controller Number 21–30, 52–54)

Status 2nd Byte 3rd ByteBnH ccH vvH

* These transmit the value when fader/knob level has been changed.

cc= Control Change Number: 00H–7FH (See the correspondence table below.)

cc Corresponding fader/knob cc Corresponding fader/knob

15H CH [1] fader 1CH HDMI [2] knob

16H CH [2] fader 1DH HDMI [3] knob

17H CH [3] fader 1EH HDMI [4] knob

18H CH [4] fader 1FH USB [FROM PC] knob

19H CH [5/6] fader 34H [MAIN] fader

1AH CH [7/8] fader 35H [AUX] fader

1BH HDMI [1] knob 36H USB [To PC] knob

vv= Control Value: 00H–7FH (0–127) The following table shows how fader values correspond to control values (unit: dB).

0 -Inf 32 -33.1 64 -11.3 96 -0.3

1 -80.0 33 -32.3 65 -10.7 97 0.02 -76.7 34 -31.5 66 -10.3 98 0.33 -73.3 35 -30.8 67 -10.0 99 0.74 -70.0 36 -30.0 68 -9.7 100 1.05 -66.7 37 -29.3 69 -9.3 101 1.36 -63.3 38 -28.7 70 -9.0 102 1.77 -60.0 39 -28.0 71 -8.7 103 2.08 -58.6 40 -27.3 72 -8.3 104 2.39 -57.1 41 -26.7 73 -8.0 105 2.710 -55.7 42 -26.0 74 -7.7 106 3.011 -54.3 43 -25.3 75 -7.3 107 3.312 -52.9 44 -24.7 76 -7.0 108 3.713 -51.4 45 -24.0 77 -6.7 109 4.014 -50.0 46 -23.3 78 -6.3 110 4.315 -48.9 47 -22.7 79 -6.0 111 4.716 -47.8 48 -22.0 80 -5.7 112 5.017 -46.7 49 -21.3 81 -5.3 113 5.318 -45.6 50 -20.7 82 -5.0 114 5.719 -44.4 51 -20.0 83 -4.7 115 6.020 -43.3 52 -19.3 84 -4.3 116 6.321 -42.2 53 -18.7 85 -4.0 117 6.722 -41.1 54 -18.0 86 -3.7 118 7.023 -40.0 55 -17.3 87 -3.3 119 7.324 -39.2 56 -16.7 88 -3.0 120 7.725 -38.5 57 -16.0 89 -2.7 121 8.026 -37.7 58 -15.3 90 -2.3 122 8.327 -36.9 59 -14.7 91 -2.0 123 8.728 -36.2 60 -14.0 92 -1.7 124 9.029 -35.4 61 -13.3 93 -1.3 125 9.330 -34.6 62 -12.7 94 -1.0 126 9.731 -33.8 63 -12.0 95 -0.7 127 10.0


vv: 00H–03H (CH 1–4)

* This transmits the value when the VIDEO INPUT SELECT [1], [2], [3], or [4] button has been operated and the output video has been switched.


vv: 00H–03H (CH 1–4)

* This transmits the value when the VIDEO INPUT SELECT [1], [2], [3], or [4] button has been operated and the video for composition has been switched.


vv: 00H–02H (CUT, MIX, WIPE)

* This transmits the value when the [CUT], [MIX], or [WIPE] button has been operated.


vv: 00H–28H (0.0–4.0 sec)

* This transmits the value when video transition time has been changed.



* This transmits the value when the [KEY] button has been operated.


vv: 00H–04H (OFF, CH 1–4)

* This transmits the value when the channel for key composition has been changed.


vv: 00H–7FH (0–127)• The sent value is one-half that of the setting on the unit.

* This transmits the key-compositing level of the currently selected KEY TYPE.

�{ Undefined (Controller Number 58)Status 2nd Byte 3rd ByteBnH 3AH vvH

vv: 00H–7FH (0–127)

* This transmits the value when the video effect level has been changed.

MIDI Implementation

29

�{ Undefined (Controller Number 59)Status 2nd Byte 3rd ByteBnH 3BH vvH

vv: 00H–03H (OFF, PinP, SPLIT, QUAD)

* This transmits the value when the [PinP], [SPLIT], or [QUAD] button has been operated.

�{ Undefined (Controller Number 60)Status 2nd Byte 3rd ByteBnH 3CH vvH


* This transmits the value when the [OUTPUT FADE] button has been operated.

�{ Undefined (Controller Number 61)Status 2nd Byte 3rd ByteBnH 3DH vvH


* This transmits the value when the [FREEZE] button has been operated.

��System Exclusive MessageStatus Data Byte StatusF0H iiH,ddH,...,eeH F7H

F0H: Status of system exclusive messageii= ID number: This is the ID to recognize manufacturer of the exclusive

message (manufacturer ID). The manufacturer ID of Roland is 41H. The ID numbers of 7EH and 7FH are expansion of MIDI standards and used as universal non-realtime message (7EH) of universal realtime message (7FH).

dd,...,ee= data: 00H–7FH (0–127)F7H: EOX (end of exclusive)

�z Data Set 1 (DT1)This is the message of actual data transmission. Use this when you want to set data to the unit.

Status Data Byte StatusF0H 41H, 10H, 00H, 00H, 00H, 29H, 12H, aaH, F7H bbH, ccH, ddH, ..., eeH, sum

Byte ExplanationF0H Exclusive Status41H Manufacturer ID (Roland)10H Device ID00H 1st byte of model ID (VR-4HD)00H 2nd byte of model ID (VR-4HD)00H 3rd byte of model ID (VR-4HD)29H 4th byte of model ID (VR-4HD)12H Command ID (DT1)aaH Address upper bytebbH Address middle byteccH Address lower byteddH Data: actual data to transmit. Multiple byte data is sent in address order. : :eeH Datasum ChecksumF7H EOX (end of exclusive)

* Data exceeding 256 bytes should be divided into packets of 256 bytes or smaller. If you send sequentially, the intervals of packets should be longer than 20 ms.

MIDI Implementation

30

3. Parameter Address Map* At addresses with “#” appended, the specified data is transmitted divided into 2 bytes or 3 bytes. The data is ignored if the entire continuous sequence is not received in

succession.

Start Address Description

00H 00H 00H Video Parameter Area

01H 00H 00H Audio Parameter Area

03H 00H 00H System Parameter Area

�z Video Parameter AreaAddress Parameter Name

00H 00H 00H CH4 Parameter

00H 01H 00H TRANSITION Parameter

00H 02H 00H PinP Parameter

00H 03H 00H SPLIT Parameter

00H 04H 00H KEY Parameter

00H 05H 00H VIDEO FX Parameter

00H 06H 00H OUTPUT Parameter

00H 07H 00H PANEL Parameter

00H 08H 00H IN/OUT SETUP Parameter

�{ CH4 ParameterAddress Parameter Name Sys.Ex.Value Meaning of Value

00H 00H 00H CH4 RESOLUTION (EDID) 00H–0EHAUTO, 480/576i, 480/576p, 720p, 1080i, 1080p, 640x480, 800x600, 1024x768, 1280x768, 1280x1024, 1366x768, 1400x1050, 1600x1200, 1920x1200

00H 00H 01H CH4 SCALING TYPE 00H–03H FULL, LETTERBOX, CROP, DOT BY DOT

#00H 00H 02H 03H

CH4 H. POSITION0aaaaaaa0bbbbbbb

aaaaaaabbbbbbb = -1920–1920* Only values that are multiples of 8 can be specified.

#00H 00H 04H 05H

CH4 V. POSITION0aaaaaaa0bbbbbbb

aaaaaaabbbbbbb = -1200–1200

00H 00H 06H CH4 H. SIZE 00H–78H 80–200 %

00H 00H 07H CH4 V. SIZE 00H–78H 80–200 %

00H 00H 08H CH4 CONTRAST 00H–7FH -64–63

00H 00H 09H CH4 SATURATION 00H–7FH -64–63

00H 00H 0AH CH4 BRIGHTNESS 00H–7FH -64–63

00H 00H 0BH Reserved

00H 00H 0CH CH4 FLICKER FILTER 00H–0AH 0–10

�{ TRANSITION ParameterAddress Parameter Name Sys.Ex.Value Meaning of Value

00H 01H 00H MIX PATTERN 00H–03H MIX, FAM, NAM, MOSAIC

00H 01H 01H WIPE PATTERN 00H–1DH

H-DOWN, H-UP, V-RIGHT, V-LEFT, H-IN, H-OUT, V-IN, V-OUT, R-DOWN, L-DOWN, R-UP, L-UP, BLOCK, V-GRID, H-GRID, H-DOWN/s, H-UP/s, V-RIGHT/s, V-LEFT/s, H-IN/s, H-OUT/s, V-IN/s, V-OUT/s, -DOWN/s, L-DOWN/s, R-UP/s, L-UP/s, BLOCK/s, V-GRID/s, H-GRID/s

00H 01H 02H TRANSITION TIME 00H–28H 0–4.0 sec

�{ PinP ParameterAddress Parameter Name Sys.Ex.Value Meaning of Value

00H 02H 00H PinP SIZE 00H–02H 1/4, 1/2, 1/3

00H 02H 01H PinP BORDER WIDTH 00H–0FH 0–15

00H 02H 02H PinP BORDER COLOR 00H–06H BLACK, WHITE, GRAY, RED, GREEN, BLUE, YELLOW

00H 02H 03H PinP PREVIOUS SELECT 00H–01H OFF, ON

00H 02H 04H PinP H. POSITION 00H–64H -50–+50 %

00H 02H 05H PinP V. POSITION 00H–64H -50–+50 %

00H 02H 06H SHAPE 00H–03H SQUARE, DIAMOND, CIRCLE, HEART

00H 02H 07H ASPECT 00H–01H 16:9, 1:1

00H 02H 08H H. CROPPING 01H–64H 1–100%

00H 02H 09H V. CROPPING 01H–64H 1–100%

00H 02H 0AH H. VIEW POSITION 00H–64H -50–+50%

00H 02H 0BH V. VIEW POSITION 00H–64H -50–+50%

MIDI Implementation

31

�{ SPLIT ParameterAddress Parameter Name Sys.Ex.Value Meaning of Value

00H 03H 00H SPLIT PATTERN 00H–03H V.CENTER, H.CENTER, V.STRETCH, H.STRETCH

00H 03H 01H SPLIT A-CENTER 00H–64H 0–100 %

00H 03H 02H SPLIT B-CENTER 00H–64H 0–100 %

00H 03H 03H SPLIT PREVIOUS SELECT 00H–01H OFF, ON

00H 03H 04H CENTER POSITION 4EH–7FH, 00H–32H -50–+50%

�{ KEY ParameterAddress Parameter Name Sys.Ex.Value Meaning of Value

00H 04H 00H KEY TYPE 00H–01H CHROMA, LUMI

00H 04H 01H KEY SOURCE CH 00H–05H OFF, CH 1–4, STILL

#00H 04H 02H 03H

CHROMA KEY LEVEL0aaaaaaa0bbbbbbb

aaaaaaabbbbbbb = 0–255

#00H 04H 04H 05H

CHROMA KEY GAIN0aaaaaaa0bbbbbbb


00H 04H 06H CHROMA KEY COLOR 00H–01H BLUE, GREEN

#00H 04H 07H 08H

CHROMA KEY HUE WIDTH0aaaaaaa0bbbbbbb


#00H 04H 09H 0AH

CHROMA KEY HUE FINE0aaaaaaa0bbbbbbb


#00H 04H 0BH 0CH

CHROMA KEY SATURATION WIDTH0aaaaaaa0bbbbbbb


#00H 04H 0DH 0EH

CHROMA KEY SATURATION FINE0aaaaaaa0bbbbbbb


#00H 04H 0FH 10H

LUMI KEY LEVEL0aaaaaaa0bbbbbbb


#00H 04H 11H 12H

LUMI KEY GAIN0aaaaaaa0bbbbbbb


00H 04H 13H LUMI KEY COLOR 00H–01H BLACK, WHITE

�{ VIDEO FX ParameterAddress Parameter Name Sys.Ex.Value Meaning of Value

00H 05H 00H EFFECT TYPE 00H–08HOFF, NEGATIVE, EMBOSS, COLORIZE, COLORPASS, POSTERIZE, SILHOUETTE, MONOCOLOR, FINDEDGE

00H 05H 01H VALUE 00H–7FH 0–127

�{ OUTPUT ParameterAddress Parameter Name Sys.Ex.Value Meaning of Value

00H 06H 00H OUTPUT RESOLUTION (EDID) 00H–0EHAUTO, 480/576i, 480/576p, 720p, 1080i, 1080p, 640x480, 800x600, 1024x768, 1280x768, 1280x1024, 1366x768, 1400x1050, 1600x1200, 1920x1200

00H 06H 01H OUTPUT SCALING TYPE 00H–03H FULL, LETTERBOX, CROP, DOT BY DOT

#00H 06H 02H 03H

OUTPUT H. POSITION0aaaaaaa0bbbbbbb

aaaaaaabbbbbbb = -1920–1920* Only values that are multiples of 8 can be specified.

#00H 06H 04H 05H

OUTPUT V. POSITION0aaaaaaa0bbbbbbb


00H 06H 06H OUTPUT H. SIZE 00H–78H 80–200 %

00H 06H 07H OUTPUT V. SIZE 00H–78H 80–200 %

00H 06H 08H OUTPUT CONTRAST 00H–7FH -64–63

00H 06H 09H OUTPUT SATURATION 00H–7FH -64–63

00H 06H 0AH OUTPUT BRIGHTNESS 00H–7FH -64–63

00H 06H 0BH OUTPUT COLOR SPACE 00H–03H AUTO, RGB-FULL, RGB-LIMIT, YPbPr

00H 06H 0CH OUTPUT DVI-D/HDMI 01H–02H DVI-D, HDMI

00H 06H 0DH PREVIEW CONTRAST 00H–7FH -64–63

00H 06H 0EH PREVIEW SATURATION 00H–7FH -64–63

00H 06H 0FH PREVIEW BRIGHTNESS 00H–7FH -64–63

00H 06H 10H PREVIEW COLOR SPACE 00H–03H AUTO, RGB-FULL, RGB-LIMIT, YPbPr

00H 06H 11H PREVIEW DVI-D/HDMI 01H–02H DVI-D, HDMI

00H 06H 12H OUTPUT FADE 00H–02H BLACK, WHITE, STILL

#00H 06H 13H 14H

OUTPUT FADE WHITE LEVEL0aaaaaaa0bbbbbbb


#00H 06H 15H 16H

OUTPUT FADE BLACK LEVEL0aaaaaaa0bbbbbbb


MIDI Implementation

32

�{ PANEL ParameterAddress Parameter Name Sys.Ex.Value Meaning of Value

00H 07H 00H VIDEO CH SELECT 00H–03H CH 1–4

00H 07H 01H VIDEO SUB CH SELECT 00H–03H CH 1–4

00H 07H 02H TRANSITION TYPE 00H–02H CUT, MIX, WIPE

00H 07H 03H COMPOSITION TYPE 00H–03H OFF, PinP, SPLIT, QUAD

00H 07H 04H KEY SW 00H–01H OFF, ON

00H 07H 05H OUTPUT FADE SW 00H–01H OFF, ON

00H 07H 06H FREEZE SW 00H–01H OFF, ON

00H 07H 07H FREEZE SELECT 00H–03H CH 1–4

�{ IN/OUT SETUP ParameterAddress Parameter Name Sys.Ex.Value Meaning of Value

00H 08H 00H CH4 INPUT SELECT 00H–02H HDMI, RGB, COMPOSITE

00H 08H 01H PVW OUTPUT SELECT 00H–01H MAIN, PVW

00H 08H 02H USB OUTPUT SELECT 00H–01H MAIN, PVW

�z Audio Parameter AreaAddress Parameter Name





01H 04H 00H CH5/6 Parameter

01H 05H 00H CH7/8 Parameter

01H 06H 00H HDMI1 Parameter




01H 0AH 00H USB Parameter

01H 0BH 00H OUTPUT CH Parameter

01H 20H 00H AUDIO FOLLOW Parameter

01H 30H 00H AUTO MIXER Parameter

01H 40H 00H ECHO CANCEL Parameter

�{ CH1–4 Parameter* “xxH” corresponds to the respective channels as indicated below.

xxH: 00H–03H (CH 1–4)

Address Parameter Name Sys.Ex.Value Meaning of Value

01H xxH 00H CH1–4 HA GAIN 00H–40H 0–64 dB

#01H xxH 01H 02H

CH1–4 GAIN0aaaaaaa0bbbbbbb

aaaaaaabbbbbbb = -42.0–42.0 dB

#01H xxH 03H 04H 05H

CH1–4 LEVEL0aaaaaaa0bbbbbbb0ccccccc

aaaaaaabbbbbbbccccccc = -32768 : -INF dB -80.0–+10.0 dB

#01H xxH 06H 07H 08H

CH1–4 AUX SEND0aaaaaaa0bbbbbbb0ccccccc


#01H xxH 09H 0AH 0BH

CH1–4 REV SEND0aaaaaaa0bbbbbbb0ccccccc


01H xxH 0CH CH1–4 PAN 00H–7FH LEFT–RIGHT

01H xxH 0DH :01H xxH 0FH

Reserved

#01H xxH 10H 11H

CH1–4 EQ HI GAIN0aaaaaaa0bbbbbbb


01H xxH 12H CH1–4 EQ HI FREQ 44H–78H 1.00–20.0KHz

#01H xxH 13H 14H

CH1–4 EQ MID GAIN0aaaaaaa0bbbbbbb


01H xxH 15H CH1–4 EQ MID FREQ 00H–78H 20 Hz–20.0 KHz

01H xxH 16H CH1–4 EQ MID Q 00H–05H 0.5–16.0

MIDI Implementation

33


#01H xxH 17H 18H

CH1–4 EQ LO GAIN0aaaaaaa0bbbbbbb


01H xxH 19H CH1–4 EQ LO FREQ 00H–38H 20–500 Hz

01H xxH 1AH :01H xxH 1FH

Reserved

01H xxH 20H CH1–4 GATE SW 00H–01H OFF, ON

#01H xxH 21H 22H

CH1–4 GATE THRESHOLD0aaaaaaa0bbbbbbb


01H xxH 23H CH1–4 GATE RELEASE 00H–7FH 30–5000 ms

01H xxH 24H CH1–4 COMP SW 00H–01H OFF, ON

#01H xxH 25H 26H

CH1–4 COMP THRESHOLD0aaaaaaa0bbbbbbb


01H xxH 27H CH1–4 COMP RATIO 00H–0DH1.0:1, 1.12:1, 1.25:1, 1.40:1, 1.60:1, 1.80:1, 2.00:1, 2.50:1, 3.20:1, 4.00:1, 5.60:1, 8.00:1, 16.0:1, INF:1

01H xxH 28H CH1–4 COMP ATTACK 00H–19H 0.2–100 ms

01H xxH 29H CH1–4 COMP RELEASE 00H–7FH 30–5000 ms

01H xxH 2AH CH1–4 COMP AUTO GAIN SW 00H–01H OFF, ON

#01H xxH 2BH 2CH

CH1–4 COMP MAKEUP GAIN0aaaaaaa0bbbbbbb


01H xxH 2DH CH1–4 HPF 00H–01H OFF, ON

01H xxH 2EH Reserved

01H xxH 2FH Reserved

#01H xxH 30H 31H

CH1–4 DELAY0aaaaaaa0bbbbbbb

aaaaaaabbbbbbb = 0.0–500.0 ms

01H xxH 32H CH1–4 SOLO 00H–01H OFF, ON

01H xxH 33H CH1–4 MUTE 00H–01H OFF, ON

�{ CH5/6, CH7/8, HDMI1–4, USB Parameter* “xxH” corresponds to the respective channels as indicated below.

xxH: 04H–0AH (CH5/6, CH7/8, HDMI1–4, USB)


01H xxH 00H Reserved

#01H xxH 01H 02H

GAIN0aaaaaaa0bbbbbbb


#01H xxH 03H 04H 05H

LEVEL0aaaaaaa0bbbbbbb0ccccccc


#01H xxH 06H 07H 08H

AUX SEND0aaaaaaa0bbbbbbb0ccccccc


#01H xxH 09H 0AH 0BH

REV SEND0aaaaaaa0bbbbbbb0ccccccc


01H xxH 0CH :01H xxH 0FH

Reserved

#01H xxH 10H 11H

EQ HI GAIN0aaaaaaa0bbbbbbb


01H xxH 12H EQ HI FREQ 44H–78H 1.00–20.0 KHz

#01H xxH 13H 14H

EQ MID GAIN0aaaaaaa0bbbbbbb


01H xxH 15H EQ MID FREQ 00H–78H 20 Hz–20.0 KHz

01H xxH 16H EQ MID Q 00H–05H 0.5–16.0

#01H xxH 17H 18H

EQ LO GAIN0aaaaaaa0bbbbbbb


01H xxH 19H EQ LO FREQ 00H–38H 20–500 Hz

01H xxH 1AH :01H xxH 2FH

Reserved

#01H xxH 30H 31H

DELAY0aaaaaaa0bbbbbbb

aaaaaaabbbbbbb = 0.0–500.0 ms

01H xxH 32H SOLO 00H–01H OFF, ON

01H xxH 33H MUTE 00H–01H OFF, ON

MIDI Implementation

34

�{ OUTPUT CH ParameterAddress Parameter Name Sys.Ex.Value Meaning of Value

#01H 0BH 00H 01H 02H

MAIN LEVEL0aaaaaaa0bbbbbbb0ccccccc


#01H 0BH 03H 04H 05H

AUX LEVEL0aaaaaaa0bbbbbbb0ccccccc


#01H 0BH 06H 07H 08H

PHONES LEVEL0aaaaaaa0bbbbbbb0ccccccc


#01H 0BH 09H 0AH 0BH

USB OUT LEVEL0aaaaaaa0bbbbbbb0ccccccc


01H 0BH 0CH :01H 0BH 0FH

Reserved

#01H 0BH 10H 11H

MAIN EQ HI GAIN0aaaaaaa0bbbbbbb


01H 0BH 12H MAIN EQ HI FREQ 44H–78H 1.00–20.0 KHz

#01H 0BH 13H 14H

MAIN EQ MID GAIN0aaaaaaa0bbbbbbb


01H 0BH 15H MAIN EQ MID FREQ 00H–78H 20Hz–20.0 KHz

01H 0BH 16H MAIN EQ MID Q 00H–05H 0.5–16.0

#01H 0BH 17H 18H

MAIN EQ LO GAIN0aaaaaaa0bbbbbbb


01H 0BH 19H MAIN EQ LO FREQ 00H–38H 20–500 Hz

01H 0BH 1AH :01H 0BH 2FH

Reserved

#01H 0BH 30H 31H

USB TO PC DELAY0aaaaaaa0bbbbbbb


#01H 0BH 32H 33H

AUX DELAY0aaaaaaa0bbbbbbb

30–5000 ms

01H 0BH 34H MAIN MUTE SW 00H–01H OFF, ON

01H 0BH 35H AUX MUTE SW 00H–01H OFF, ON

01H 0BH 36H USB OUT MUTE SW 00H–01H OFF, ON

01H 0BH 37H :01H 0BH 3FH

Reserved

#01H 0BH 40H 41H 42H

REVERB LEVEL0aaaaaaa0bbbbbbb0ccccccc


01H 0BH 43H REVERB TYPE 00H–01H ROOM/HALL

01H 0BH 44H REVERB TIME 00H–32H 0.0–5.0 sec

01H 0BH 45H Main MBC SW 00H–01H OFF, ON

#01H 0BH 46H 47H

Main MBC Hi Thres0aaaaaaa0bbbbbbb


01H 0BH 48H Main MBC Hi Ratio 00H–0DH1.0:1, 1.12;1, 1.25:1, 1.40:1, 1.60:1, 1.80:1, 2.00:1, 2.50:1, 3.20:1, 4.00;1, 5.60:1, 8.00;1, 16.0:1. INF:1

#01H 0BH 49H 4AH

Main MBC Mid Thres0aaaaaaa0bbbbbbb


01H 0BH 4BH Main MBC Mid Ratio 00H–0DH1.0:1, 1.12;1, 1.25:1, 1.40:1, 1.60:1, 1.80:1, 2.00:1, 2.50:1, 3.20:1, 4.00;1, 5.60:1, 8.00;1, 16.0:1. INF:1

#01H 0BH 4CH 4DH

Main MBC Low Thres0aaaaaaa0bbbbbbb


01H 0BH 4EH Main MBC Low Ratio 00H–0DH1.0:1, 1.12;1, 1.25:1, 1.40:1, 1.60:1, 1.80:1, 2.00:1, 2.50:1, 3.20:1, 4.00;1, 5.60:1, 8.00;1, 16.0:1. INF:1

01H 0BH 4FH Main Lmt SW 00H–01H OFF, ON

#01H 0BH 50H 51H

Main Lmt Thres0aaaaaaa0bbbbbbb


01H 0BH 52H Phones Lmt SW 00H–01H OFF, ON

#01H 0BH 53H 54H

Phones Lmt Thres0aaaaaaa0bbbbbbb


01H 0BH 55H MAIN Out Select 00H–01H MAIN, AUX

01H 0BH 56H AUX Out Select 00H–01H MAIN, AUX

01H 0BH 57H USB Out Select 00H–01H MAIN, AUX

MIDI Implementation

35


01H 0BH 58H Phones Out Select 00H–01H MAIN, AUX

�{ AUDIO FOLLOW ParameterAddress Parameter Name Sys.Ex.Value Meaning of Value

01H 20H 00H AUDIO FOLLOW SW 00H–01H OFF, ON

01H 20H 01H AUDIO FOLLOW SW Output Fade 00H–01H OFF, ON

01H 20H 02H :01H 20H 0FH

Reserved

01H 20H 10H AUDIO FOLLOW CH1 VideoCh1 00H–01H OFF, ON










01H 20H 1AH AUDIO FOLLOW CH3 VideoCh3 00H–01H OFF, ON

01H 20H 1BH AUDIO FOLLOW CH3 VideoCh4 00H–01H OFF, ON

01H 20H 1CH AUDIO FOLLOW CH4 VideoCh1 00H–01H OFF, ON

01H 20H 1DH AUDIO FOLLOW CH4 VideoCh2 00H–01H OFF, ON

01H 20H 1EH AUDIO FOLLOW CH4 VideoCh3 00H–01H OFF, ON

01H 20H 1FH AUDIO FOLLOW CH4 VideoCh4 00H–01H OFF, ON

01H 20H 20H AUDIO FOLLOW CH5/6 VideoCh1 00H–01H OFF, ON








01H 20H 28H AUDIO FOLLOW HDMI1 VideoCh1 00H–01H OFF, ON


01H 20H 2AH AUDIO FOLLOW HDMI1 VideoCh3 00H–01H OFF, ON

01H 20H 2BH AUDIO FOLLOW HDMI1 VideoCh4 00H–01H OFF, ON

01H 20H 2CH AUDIO FOLLOW HDMI2 VideoCh1 00H–01H OFF, ON

01H 20H 2DH AUDIO FOLLOW HDMI2 VideoCh2 00H–01H OFF, ON

01H 20H 2EH AUDIO FOLLOW HDMI2 VideoCh3 00H–01H OFF, ON

01H 20H 2FH AUDIO FOLLOW HDMI2 VideoCh4 00H–01H OFF, ON









01H 20H 38H AUDIO FOLLOW USB VideoCh1 00H–01H OFF, ON

01H 20H 39H AUDIO FOLLOW USB VideoCh2 00H–01H OFF, ON

01H 20H 3AH AUDIO FOLLOW USB VideoCh3 00H–01H OFF, ON

01H 20H 3BH AUDIO FOLLOW USB VideoCh4 00H–01H OFF, ON

�{ AUDIO MIXER ParameterAddress Parameter Name Sys.Ex.Value Meaning of Value

01H 30H 00H AUTO MIXER SW 00H–01H OFF, ON

01H 30H 01H AUTO MIXER CH1 SW 00H–01H OFF, ON

01H 30H 02H AUTO MIXER CH1 WEIGHT 00H–64H 0–100



MIDI Implementation

36






01H 30H 09H AUTO MIXER CH5/6 SW 00H–01H OFF, ON

01H 30H 0AH AUTO MIXER CH5/6 WEIGHT 00H–64H 0–100

01H 30H 0BH AUTO MIXER CH7/8 SW 00H–01H OFF, ON

01H 30H 0CH AUTO MIXER CH7/8 WEIGHT 00H–64H 0–100

01H 30H 0DH AUTO MIXER HDMI1 SW 00H–01H OFF, ON

01H 30H 0EH AUTO MIXER HDMI1 WEIGHT 00H–64H 0–100

01H 30H 0FH AUTO MIXER HDMI2 SW 00H–01H OFF, ON

01H 20H 10H AUTO MIXER HDMI2 WEIGHT 00H–64H 0–100

01H 20H 11H AUTO MIXER HDMI3 SW 00H–01H OFF, ON


01H 20H 13H AUTO MIXER HDMI4 SW 00H–01H OFF, ON


�z System Parameter AreaAddress Parameter Name

03H 00H 00H VERSION Parameter

03H 01H 00H03H 04H 00H

SETUP Parameter

03H 02H 00H REMOTE Parameter

03H 03H 00H MEMORY Parameter

�{ Version ParameterAddress Parameter Name Sys.Ex.Value Meaning of Value

03H 00H 00H System Version String (1) 00H–7FH ASCII Character (Read Only)








�{ Setup ParameterAddress Parameter Name Sys.Ex.Value Meaning of Value

03H 01H 00H HDCP SW 00H–01H OFF, ON

03H 01H 01H FRAME RATE 00H–01H 59.94 Hz, 50 Hz

03H 01H 02H SYSTEM FORMAT 00H–02H 720p, 1080i, 1080p

03H 01H 03H LCD BRIGHTNESS 00H–01H LOW, HIGH

03H 01H 04H MENU DISPLAY LEVEL 05H–0FH 5–15

03H 01H 05H LEVEL METER DISPLAY 00H–01H OFF, ON

03H 01H 06H INPUT CH LABEL DISPLAY 00H–01H OFF, ON

03H 01H 07H TALLY LABEL DISPLAY 00H–01H OFF, ON

03H 01H 08H NO SIGNAL BACK 00H–01H BLACK, BLUE

03H 01H 09H UNFIT SIGNAL BACK 00H–02H BLACK, BLUE, THRU

03H 01H 0AH DEINTERLACE MODE 00H–01H WEAVE, BOB

03H 01H 0BH COLOR BAR OUTPUT 00H–01H OFF, ON

03H 01H 0CH TEST TONE OUTPUT 00H–01H OFF, ON

03H 01H 0DH AUTO OFF 00H–01H OFF, ON

03H 01H 0EH PANEL LOCK 00H–01H OFF, ON

03H 01H 0FH MONITOR BUTTON LOCK 00H–01H OFF, ON

03H 01H 10H TOUCH PANEL LOCK 00H–01H OFF, ON

03H 01H 11H FREEZE MODE 00H–01H ALL, SELECT

03H 01H 12H AUTO SWITCHING SW 00H–01H OFF, ON

03H 01H 14H USB CONNECTION STATUS 00H–02H NC, USB2.0, USB3.0 (Read Only)

MIDI Implementation

37


03H 04H 00H AUTO SWITCHING TYPE 00H–02H AUTO SCAN, BEAT SYNC SWITCHING, VIDEO FOLLOWS AUDIO

03H 04H 01H AUTO SW TRANSITION TIME 00H–28H 0.0–4.0sec

03H 04H 02HAUTO SCAN SCANTIME VIDEO INPUT 1

00H–78H OFF, 1–120sec


00H–78H OFF, 1–120sec


00H–78H OFF, 1–120sec


00H–78H OFF, 1–120sec

03H 04H 06H AUTO SCAN SEQUENCE 00H–01H NORMAL, RANDOM

03H 04H 07HBEAT SYNC SWITCHING SYNC SOURCE

00H–0AH IN1, IN2, IN3, IN4, IN5/6, IN7/8, HDMI1, HDMI2, HDMI3, HDMI4, USB FROM PC

03H 04H 08H BEAT SYNC SWITCHING CYCLE 01H–10H 1–16

03H 04H 09H BEAT SYNC SWITCHING SEQUENCE 00H–01H NORMAL, RANDOM

03H 04H 0AHBEAT SYNC SWITCHING VIDEO INPUT1 SW

00H–01H OFF, ON

03H 04H 0BHBEAT SYNC SWITCHING VIDEO INPUT2 SW

00H–01H OFF, ON

03H 04H 0CHBEAT SYNC SWITCHING VIDEO INPUT3 SW

00H–01H OFF, ON

03H 04H 0DHBEAT SYNC SWITCHING VIDEO INPUT4 SW

00H–01H OFF, ON

03H 04H 0EH VIDEO FOLLOWS AUDIO TIME 01H–78H 1–120sec

03H 04H 0FHVIDEO FOLLOWS AUDIO INPUT1 SENSE

00H–64H 0–100

03H 04H 10HVIDEO FOLLOWS AUDIO INPUT2 SENSE

00H–64H 0–100


00H–64H 0–100


00H–64H 0–100

03H 04H 13HVIDEO FOLLOWS AUDIO INPUT1 SELECT

00H–05H OFF, 1, 2, 3, 4, QUAD


00H–05H OFF, 1, 2, 3, 4, QUAD


00H–05H OFF, 1, 2, 3, 4, QUAD


00H–05H OFF, 1, 2, 3, 4, QUAD

03H 04H 17HVIDEO FOLLOWS AUDIO MULTI INPUT SELECT

00H–05H OFF, 1, 2, 3, 4, QUAD

03H 04H 18HVIDEO FOLLOWS AUDIO SILENT SELECT

00H–06H OFF, 1, 2, 3, 4, QUAD, AUTO SCAN

03H 04H 1AHPANEL LOCK VIDEO INPUT CH1 BUTTON

00H–01H OFF, ON

03H 04H 1BHPANEL LOCK VIDEO INPUT CH2 BUTTON

00H–01H OFF, ON

03H 04H 1CHPANEL LOCK VIDEO INPUT CH3 BUTTON

00H–01H OFF, ON

03H 04H 1DHPANEL LOCK VIDEO INPUT CH4 BUTTON

00H–01H OFF, ON

03H 04H 1EH PANEL LOCK OUTPUT FADE BUTTON 00H–01H OFF, ON

03H 04H 1FH PANEL LOCK KEY BUTTON 00H–01H OFF, ON

03H 04H 20H PANEL LOCK IN/OUT SETUP BUTTON 00H–01H OFF, ON

03H 04H 21HPANEL LOCK VFX / KEY LEVEL BUTTON

00H–01H OFF, ON

03H 04H 22H PANEL LOCK FREEZE BUTTON 00H–01H OFF, ON

03H 04H 23H PANEL LOCK PinP BUTTON 00H–01H OFF, ON

03H 04H 24H PANEL LOCK SPLIT BUTTON 00H–01H OFF, ON

03H 04H 25H PANEL LOCK QUAD BUTTON 00H–01H OFF, ON

03H 04H 26H PANEL LOCK CUT BUTTON 00H–01H OFF, ON

03H 04H 27H PANEL LOCK MIX BUTTON 00H–01H OFF, ON

03H 04H 28H PANEL LOCK WIPE BUTTON 00H–01H OFF, ON

03H 04H 29H PANEL LOCK TRANSITION TIME KNOB 00H–01H OFF, ON

MIDI Implementation

38


03H 04H 2AH PANEL LOCK USER1 BUTTON 00H–01H OFF, ON

03H 04H 2BH PANEL LOCK USER2 BUTTON 00H–01H OFF, ON

03H 04H 2CH PANEL LOCK USER3 BUTTON 00H–01H OFF, ON

03H 04H 2DH PANEL LOCK USER4 BUTTON 00H–01H OFF, ON

03H 04H 2EH PANEL LOCK USER5 BUTTON 00H–01H OFF, ON

03H 04H 2FH PANEL LOCK USER SETUP BUTTON 00H–01H OFF, ON

03H 04H 30H PANEL LOCK HDMI1 LEVEL KNOB 00H–01H OFF, ON




03H 04H 34H PANEL LOCK HDMI SETUP BUTTON 00H–01H OFF, ON

03H 04H 35H PANEL LOCK USB FROM PC KNOB 00H–01H OFF, ON

03H 04H 36H PANEL LOCK USB TO PC KNOB 00H–01H OFF, ON

03H 04H 37H PANEL LOCK USB SETUP BUTTON 00H–01H OFF, ON

03H 04H 38H PANEL LOCK INPUT1 GAIN KNOB 00H–01H OFF, ON

03H 04H 39H PANEL LOCK INPUT2 GAIN KNOB 00H–01H OFF, ON

03H 04H 3AH PANEL LOCK INPUT3 GAIN KNOB 00H–01H OFF, ON

03H 04H 3BH PANEL LOCK INPUT4 GAIN KNOB 00H–01H OFF, ON

03H 04H 3CH PANEL LOCK INPUT1 LEVEL FADER 00H–01H OFF, ON

03H 04H 3DH PANEL LOCK INPUT2 LEVEL FADER 00H–01H OFF, ON

03H 04H 3EH PANEL LOCK INPUT3 LEVEL FADER 00H–01H OFF, ON

03H 04H 3FH PANEL LOCK INPUT4 LEVEL FADER 00H–01H OFF, ON

03H 04H 40H PANEL LOCK INPUT1 SETUP BUTTON 00H–01H OFF, ON




03H 04H 44H PANEL LOCK INPUT 5/6 LEVEL FADER 00H–01H OFF, ON

03H 04H 45HPANEL LOCK INPUT 5/6 SETUP BUTTON

00H–01H OFF, ON

03H 04H 46H PANEL LOCK INPUT 7/8 LEVEL FADER 00H–01H OFF, ON

03H 04H 47HPANEL LOCK INPUT 7/8 SETUP BUTTON

00H–01H OFF, ON

03H 04H 48H PANEL LOCK MAIN OUT LEVEL FADER 00H–01H OFF, ON

03H 04H 49HPANEL LOCK MAIN OUT SETUP BUTTON

00H–01H OFF, ON

03H 04H 4AH PANEL LOCK PHONES KNOB 00H–01H OFF, ON

03H 04H 4BH PANEL LOCK REVERB KNOB 00H–01H OFF, ON

MIDI Implementation

39

�{ Remote ParameterAddress Parameter Name Sys.Ex.Value Meaning of Value

03H 02H 00H MIDI RX Ch 00H–0FH 1–16

03H 02H 01H RS232 SW 00H–01H OFF, ON

03H 02H 02H RS232 BaudRate 00H–03H 9600, 19200, 38400, 115200

03H 02H 03H GPI 1 ASSIGN 00H–11H N/A, CH SEL 1–4, MEMLOAD 1–8, USER 1–5




03H 02H 07H GPO 1 TYPE 00H–01H ONESHOT, ALT



03H 02H 0AH GPO 4 TYPE 00H–01H ONESHOT, ALT

�{ Memory ParameterAddress Parameter Name Sys.Ex.Value Meaning of Value

03H 03H 00H MEMORY RECALL TRIGGER 00H–07H MEMORY 1–8

03H 03H 01H LOADED MEMORY NO 00H–07H, 7FH 0H–07H: MEMORY 1–8, 7FH = no load (Read Only)

03H 03H 02H MEMORY SAVE TRIGGER 00H–07H MEMORY 1–8

03H 03H 03H MEMORY INIT TRIGGER 00H–07H MEMORY 1–8

03H 03H 04H MANUAL MODE 00H–01H OFF, ON

03H 03H 05H POWER ON LOAD 00H–08H OFF, MEMORY 1–8

MIDI Implementation

40

4. Supplementary Material

�z Decimal and Hexadecimal Table(Hexadecimal Numbers are Indicated by ‘H’)In MIDI documentation, data values and addresses/sizes of exclusive messages etc. are expressed as hexadecimal values for each 7 bits.The following table shows how these correspond to decimal numbers.

+——————+——————++——————+——————++——————+——————++——————+——————+| D | H || D | H || D | H || D | H |+——————+——————++——————+——————++——————+——————++——————+——————+| 0 | 00H || 32 | 20H || 64 | 40H || 96 | 60H || 1 | 01H || 33 | 21H || 65 | 41H || 97 | 61H || 2 | 02H || 34 | 22H || 66 | 42H || 98 | 62H || 3 | 03H || 35 | 23H || 67 | 43H || 99 | 63H || 4 | 04H || 36 | 24H || 68 | 44H || 100 | 64H || 5 | 05H || 37 | 25H || 69 | 45H || 101 | 65H || 6 | 06H || 38 | 26H || 70 | 46H || 102 | 66H || 7 | 07H || 39 | 27H || 71 | 47H || 103 | 67H || 8 | 08H || 40 | 28H || 72 | 48H || 104 | 68H || 9 | 09H || 41 | 29H || 73 | 49H || 105 | 69H || 10 | 0AH || 42 | 2AH || 74 | 4AH || 106 | 6AH || 11 | 0BH || 43 | 2BH || 75 | 4BH || 107 | 6BH || 12 | 0CH || 44 | 2CH || 76 | 4CH || 108 | 6CH || 13 | 0DH || 45 | 2DH || 77 | 4DH || 109 | 6DH || 14 | 0EH || 46 | 2EH || 78 | 4EH || 110 | 6EH || 15 | 0FH || 47 | 2FH || 79 | 4FH || 111 | 6FH || 16 | 10H || 48 | 30H || 80 | 50H || 112 | 70H || 17 | 11H || 49 | 31H || 81 | 51H || 113 | 71H || 18 | 12H || 50 | 32H || 82 | 52H || 114 | 72H || 19 | 13H || 51 | 33H || 83 | 53H || 115 | 73H || 20 | 14H || 52 | 34H || 84 | 54H || 116 | 74H || 21 | 15H || 53 | 35H || 85 | 55H || 117 | 75H || 22 | 16H || 54 | 36H || 86 | 56H || 118 | 76H || 23 | 17H || 55 | 37H || 87 | 57H || 119 | 77H || 24 | 18H || 56 | 38H || 88 | 58H || 120 | 78H || 25 | 19H || 57 | 39H || 89 | 59H || 121 | 79H || 26 | 1AH || 58 | 3AH || 90 | 5AH || 122 | 7AH || 27 | 1BH || 59 | 3BH || 91 | 5BH || 123 | 7BH || 28 | 1CH || 60 | 3CH || 92 | 5CH || 124 | 7CH || 29 | 1DH || 61 | 3DH || 93 | 5DH || 125 | 7DH || 30 | 1EH || 62 | 3EH || 94 | 5EH || 126 | 7EH || 31 | 1FH || 63 | 3FH || 95 | 5FH || 127 | 7FH |+——————+——————++——————+——————++——————+——————++——————+——————+

D: decimalH: hexadecimal

* Decimal expressions used for MIDI channel, bank select, and program change are 1 greater than the decimal value shown in the above table.

* Hexadecimal values in 7-bit units can express a maximum of 128 levels in one byte of data. If the data requires greater resolution, two or more bytes are used. For example, a value indicated by a hexadecimal expression in two 7-bit bytes aa bbH would be aa x 128 + bb.

* Data marked “nibbled” is expressed in hexadecimal in 4-bit units. A value expressed as a 2-byte nibble 0a 0bH has the value of a x 16 + b.

<Example1> What is the decimal expression of 5AH?From the preceding table, 5AH = 90

<Example2> What is the decimal expression of the value 12 34H given as hexadecimal for each 7 bits?From the preceding table, since 12H = 18 and 34H = 5218 x 128 + 52 = 2356

<Example3> What is the decimal expression of the nibbled value 0A 03 09 0D?From the preceding table, since 0AH = 10, 03H = 3, 09H = 9, 0DH = 13((10 x 16 + 3) x 16 + 9) x 16 + 13 = 41885

<Example4> What is the nibbled expression of the decimal value 1258?

16) 125816) 78... 1016) 4... 14 0... 4

Since from the preceding table, 0 = 00H, 4 = 04H, 14 = 0EH, 10 = 0AH, the answer is 00 04 0E 0AH.

�z MIDI Message Examples<Example 1> 92H 3EH 5FH9n is a note on status and n is the MIDI channel number.As 2H = 2, 3EH = 62 and 5FH = 95, this is a note on message of MIDI CH =3 , note number 62 (D4) and velocity 95.

<Example 2> CEH 49HCnH is program change status, and n is the MIDI channel number.As EH = 14 and 49H = 73, this is a program change message of MIDI CH = 15 and program number 74 (in the GS sound map, Flute).

�z Example of an Exclusive Message and Calculating a Checksum

Roland Exclusive messages are transmitted with a checksum at the end (before F7) to make sure that the message was correctly received. The value of the checksum is determined by the address and data (or size) of the transmitted exclusive message.

�{ How to Calculate the Checksum (Hexadecimal Numbers are Indicated by ‘H’)

The checksum is a value that produces a lower 7 bits of zero when the address, size,and checksum itself are summed. If the exclusive message to be transmitted has anaddress of aa bb ccH and the data is dd ee ffH, the actual calculation would be as follows:

aa + bb + cc + dd + ee + ff = sumsum / 128 = quotient ... remainder128 - remainder = checksum(However, the checksum will be 0 if the remainder is 0.)

<Example>Setting Dissolve Time Ctrl Assign in MIDI Visual Control to Modulation for Control Changes

From the “Parameter Address Map”, the start address of the Dissolve Time Ctrl Assign in MIDI Visual Control is 10H 10H 02H and the Modulation parameter in Control Change is 00H 01H. Therefore ...

F0H 7EH 00H 0CH 01H 10H 10H 02H 00H 01H ??H F7H

(1) (2) (3) (4) (5) (6) (7) (8)

(1) Exclusive Status(2) ID Number (Universal SysEx Non Realtime)(3) Device ID (0)(4) Sub ID (MIDI Visual Control Version 1.0)(5) Address(6) Data(7) Checksum(8) EOX

Next calculate the checksum. Add (5) to (6).10H + 10H + 02H + 00H + 01H = 16 + 16 + 2 + 0 + 1 = 35 (sum)35 (sum) / 128 = 0 (quotient) ... 35 (remainder)Checksum = 128 - 35 (remainder) = 93 = 5DH

Thus, the message to transmit is :F0H 7EH 00H 0CH 01H 10H 10H 02H 00H 01H 5DH F7H

41

Function Transmitted Recognized Remarks

Basic

Channel

Default

Changed

1–16

1–16

1–16

1–16

Mode

Default

Messages

Altered

×

×

**************

×

×

**************

Note

NumberTrue Voice × ×

VelocityNote On

Note Off

×

×

×

×

After

Touch

Key’s

Channel’s

×

×

×

×

Pitch Bend × ×

ControlChange

14–15

21–30

52–54

46–47

55–61

O

O

O

O

O

O

O

O

O

O

Controls various parameters

Program

Change: True Number × ×

System Exclusive O O

System

Common

: Song Position

: Song Select

: Tune Request

×

×

×

×

×

×

System

Real Time

: Clock

: Commands

×

×

×

×

Aux

Messages

: All Sound Off

: Reset All Controllers

: Local On/Off

: All Notes Off

: Active Sensing

: System Reset

×

×

×

×

×

×

×

×

×

×

×

×

Notes

Mode 1 : OMNI ON, POLY Mode 2 : OMNI ON, MONOMode 3 : OMNI OFF, POLY Mode 4 : OMNI OFF, MONO

O : YesX : No

MIDI Implementation ChartHD AV Mixer

Model VR-4HD

Date: Mar. 16, 2017

Version: 1.50

01

* Roland is either registered trademark or trademark of Roland Corporation in the United States and/or other countries.

Documents

Reference Manual - Full Compass Systems€¦ · AUTO, 480/576i, 480/576p, 720p, 1080i, 1080p, ... H. CROPPING 1–100% This adjusts the crop size of the inset screen. ... SPLIT PATTERN