FACTORY AUTOMATION

Eco Changes from Home to Space

Direct

drive

Significant coil power consumption saving by high-efficiency polarized

electromagnet and direct drive by 24 VDC, 0.1 A rated transistor output

(24 VDC coil)

Models supported for direct drive by transistor output

SD-T type

SD-T12(2.7 kW) SD-T21(4k W)SD-T20(3.7 kW) SD-T32(7.5 kW)

Reduction of Devices Thanks to Direct Drive Technology with Programmable Controller

SD-Q type

SD-Q11(2.5 kW) SD-Q12(2.5 kW)* Capacities shown in ( ) are AC-3 ratings of 200 VAC class.

Nseries

NF32-SV MSO-N12 3-phase Motor

iQ-R / RY41NT2P

UN-SY type module

Tseries

Direct drive achieved by 24 VDC, 0.1 A transistor output Space saving as interface relay not required Terminal cover equipped as standard

NF32-SV MSOD-T12 3-phase Motor

iQ-R / RY41NT2P

Kani Factory, Mitsubishi Electric Corporation Nagoya Works

Small-lot and multi-cycle production by robot assembly cell

The small-lot production of multi-product has been common for all

industries to pursue. However, the mass production of multi-product is

sometimes required depending on the products to be manufactured.

Our Kani factory has added the robot-using production method

besides that of the existing cell-using production for the launch of

our product “MS-T series”. The small-lot/multi-cycle production

required for our magnetic starter has been achieved with the both

cell-using flexible production and robot-using mass production.

L(NA)02040ENG-＊(1810)MEE

HEAD OFFICE: TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN

www.MitsubishiElectric.com

S-T Series

Mirror Contacts(With Safety

Separation Function)

Assembly/Transport Solutions

Automobile Manufacturing Solutions

Press Machining Solutions

It is best to employ S-T series/S-N series/SD-Q series models with mirror contacts (safety separation function) in safety inverter/servo circuits for the shutting down of power in the event of an abnormality.With this application, compliance with safety categories 3 and 4 is achieved.

Contactors with Mirror Contacts <Auxiliary Break Contact OFF During Main Contact Welding>

Compliant with TÜV regulations for mirror contacts. Complies with

requirements for "control functionality during failures" stipulated in the

section "Electrical Devices of Industrial Equipment" in EN regulation

EN60204-1 and can be used as an interlocking circuit contact. (Refer

to the catalog of Mitsubishi Electric magnetic contactors and magnetic

starter for the certified models.)

Can be applied to mechanical safety category 4 circuits. (Can detect

malfunction of break contacts)

Features safety contactors and can be used to construct a completely

safe system using a wide assortment of safe parts.

Gap

Auxiliary Break Contact

Main Contact Welding

As the peripheral device for the magnetic

starter, we provide the control and drive

equipment required for building the system

and can propose the risk-free solution with

them.General

Programming Tool"GX Works3"

Safetyprogrammable controller

EmergencyStop Switch

Safety Remote I/O UnitSafety Remote I/O Unit

SafetyMat

Safetyprogrammable controller

LightCurtains

Light Curtain

Light Curtain

Robots

Contactors Breaker

LightCurtains

Robots

Motors GOT

SafetyServo

EnableSwitches

Generalprogrammable controller

Emergency StopSwitch

TeachingPendants

Additional Axes of Robots

Breaker

Breaker

Breaker

Contactors

Contactor

3-phase Motor

STO Signal

STO SignalLaser Scanner

Servo MotorIndicatorLamps

SafetyController

Contactor

Robot CPU

Door Switches

Robot Controllers

Emergency StopSwitch

SafetyServo

SafetyInverter

Emergency StopSwitch

Door Switch

GOT

GOT

GOT