CleanWay Environmental Partners Inc. | 800.723.1373 | cleanwayusa.com | PO Box 30087 | Portland OR 97294

January 9, 2018

Mr. Leo Cosentini California State Water Resources Control Board Division of Water Quality PO Box 100 Sacramento, CA 95812

Re: Storm Clean® Filtration Systems Application for Trash Treatment Control Device Certification

Dear Mr. Cosentini,

CleanWay Environmental Partners, Inc. is pleased to present this application to the California State Water Resources Control Board for the Storm Clean® filtration system’s use as a Trash Treatment Control Device. This application contains the complete supporting detail of the system according to the Trash Treatment Control Device Application Requirements. This includes the following seven sections:

1. Cover Letter2. Table of Contents3. Physical Description4. Installation Information5. Operation and Maintenance Information6. Reliability Information7. Field/Lab Testing Information and Analysis

Thank you for considering this application. Please do not hesitate to contact us if additional information is required.

Sincerely yours,

CleanWay Environmental Partners, Inc.

Steve McInnis Owner

cc: Bridget Garlinghouse, CleanWay®, Technical Sales Engineer

1

1.0 COVER LETTER

1.A. General description of the Device.

The Storm Clean® Filtration System is a full capture drop inlet filtration insert comprised of three components: a pan, a strainer, and an optional fabric or media filter. The steel strainer has 3/16” (4.8 mm) openings and effectively captures particles 5mm or greater.

1.B. The applicant’s contact information and location.

CleanWay has been manufacturing the stormwater filtration systems in Portland, Oregon since the late 1980s. We can be reached 8am to 5pm Monday through Friday at 800-723-1373.

CleanWay’s California Full Capture device contact:

Bridget Garlinghouse, EIT Technical Sales Engineer CleanWay Environmental Partners, Inc. PO Box 30087 Portland, OR 97294 503-467-2639 bridget.garlinghouse@cleanwayusa.com 1.C. The Devices’ manufacturing location.

Fabrication of all units occurs at the physical location listed below: CleanWay Environmental Partners, Inc. 5410 NE 109th Ave Portland, OR 97220 1.D. A brief summary of any field/lab testing results that demonstrates the Device

functions as described within the application.

The Storm Clean Filtration System directs all water and particles or trash carried with the water

through a screen with <5mm openings. No particles equal to or greater than 5mm diameter can

physically escape the system unless the system is in bypass. In addition to the set physical size

limitations of the screen, trash collection performance testing is currently being conducted for

further characterization of the system. This information is available upon request and will be

added as an amendment to the application once finalized.

1.E. A brief summary of the Device limitations, and operational, sizing, and maintenance consideration.

The Storm Clean Filtration system is easy to install and maintain, requiring no special tools. These systems are offered in standard sizes and custom designs for varying sizes and inlet styles. The device is limited to a minimum depth of 12” and grated inlet size of 16”. Maintenance and operation of the unit should be performed on a monthly basis to ensure the device is

3

Application for Storm Clean® Filter

Full Capture System Certification to the

California State Water Resource Control Board

CleanWay Environmental Partners, Inc. PO Box 30087

Portland, OR 97294

4

2.0 TABLE OF CONTENTS

3. PHYSICAL DESCRIPTION…………………………………………………………….. 6

Subsection 3.A………………………………………………………………….. 6

Subsection 3.B………………………………………………………………….. 6

Subsection 3.C………………………………………………………………….. 7

Subsection 3.D………………………………………………………………….. 7

Subsection 3.E………………………………………………………………….. 8

Subsection 3.F………………………………………………………………….. 8

Subsection 3.G………………………………………………………………….. 8

Subsection 3.H………………………………………………………………….. 9

Subsection 3.I…..………………………………………………………………. 9

Subsection 3.J………………………………………………………………….. 12

4. INSTALLATION INFORMATION……………………………………………………… 13

Subsection 4.A………………………………………………………………….. 13

Subsection 4.B………………………………………………………………….. 13

5. OPERATION AND MAINTENANCE INFORMATION………………………………. 14

Subsection 5.A………………………………………………………………….. 14

Subsection 5.B………………………………………………………………….. 14

Subsection 5.C………………………………………………………………….. 14

Subsection 5.D………………………………………………………………….. 15

6. RELIABILITY INFORMATION…………………………………………………………. 16

Subsection 6.A………………………………………………………………….. 16

Subsection 6.B………………………………………………………………….. 16

Subsection 6.C………………………………………………………………….. 16

7. FIELD/LAB TESTING INFORMATION AND ANALYSIS…………………………… 16

5

List of Tables

Table 1. Alternative configurations for Storm Clean® filtration inserts…............................. 6

Table 2. Storm Clean® standard design filtration specifications.......................................... 7

Table 3. Storm Clean® product materials……………………………………………………… 8

List of Figures

Figure 1. Cleaned drop inlet for Storm Clean® filtration insert............................................ 9

Figure 2. Installation of Storm Clean® drop inlet insert with media filter.............................. 10

Figure 3. Installation of Storm Clean® drop inlet insert with fabric filter.....…….…………… 10

Figure 4. Installed square Storm Clean® drop inlet insert…………….…....………………… 11

Figure 5. Installed round Storm Clean® drop inlet insert……………………………………… 11

Figure 6. Installed rectangular Storm Clean® drop inlet insert....................………………… 12

Figure 7. Storm Clean® sample port and vector control point of access……………….....… 14

APPENDICIES

Appendix A. Standard Drawings for Storm Clean® filtration units

Appendix B. Client worksheet: Measure your Catch Basin

Appendix C. Inspection and Maintenance Checklist

Appendix D. CleanWay® Limited Product Warranty

6

3.0 PHYSICAL DESCRIPTION

3.A. Design drawings for all standard Devices sizes including dimensions, and

alternative configurations.

Design drawings for Storm Clean® filtration system devices are included in Appendix A.

Alternative configurations for the Storm Clean® filtration inserts are described in Table 1, below.

Table 1. Alternative configurations for Storm Clean® filtration inserts

Item No. Description Alternative

RT_x_SED-ll Storm clean-ll complete filter insert for rectangular

catch basin with standard non-woven fabric sediment element. Specified dimensions.

For non-standard rectangular basins sized 20” and up

RT_x_SED-lll Storm clean-lll complete filter insert for rectangular

catch basin with standard non-woven fabric sediment element. Specified dimensions.

For non-standard rectangular basins sized 16” and up

RD_x_SED-ll Round type ll complete with non-woven fabric

sediment element with special dimensions For non-standard round basins

sized 20” and up

RD_x_SED-lll Round type lll complete with non-woven fabric

sediment element with special dimensions For non-standard round basins

sized 16” and up

SQDS_x_SED-ll Square dual strainer w / non-standard dimension

includes adsorb-it fabric elements For square basins sized 35” and up, accommodates larger flows

RTDS_x_SED-ll Rectangular filter insert with dual strainers and non-woven geotextile elements. Specified dimensions.

For rectangular basins sized 35” and up, accommodates larger

flows

RPSTRN-ll Storm clean-ll repl strainer, 16” depth, 0.97 ft

3

capture capacity For shallow basins,

accommodates depth limitations

RPSTRN-ll Storm clean-ll repl strainer, 12” depth, 0.73 ft

3

capture capacity For shallow basins,

accommodates depth limitations

3.B. Description on how the Device works to trap all particles that are 5mm or greater

in size and how it is sized for varying flow volumes.

Storm Clean® drop inlet filtration systems include two components: a pan, a strainer. An

optional third component can be added for water quality improvement such as a fabric or media

filter. The modular pan is designed to conform to the existing basin specifications. It is

positioned across the inlet of the storm drain, resting on flanges that set on the basin grate

frame, below the grate. The pan’s three main features are the sample port, the overflow bypass

orifice, and a tapered collar for strainer and optional filter placement. The strainer, a truncated

cone design, is constructed with 3/16” (4.8 mm) perforated steel sheet on 1/4” (6.35 mm)

centers. It drops below the pan to sit inside the basin, and includes a bail handle for ease of

installation and servicing. The filter component, an optional addition for improved water quality,

surrounds the strainer completely, and is suspended below the pan. The following filter options

are available: non-woven geotextile fabric for sediment and TSS removal, ADsorb-It® lipophilic

7

filtration fabric for oil and hydrocarbon removal, MetalZorb® dissolved heavy metals removal

media, and other specialty media for site specific needs.

The filtration system is designed for use in both existing and new storm drain infrastructure.

Standard insert sizes fit both square two foot by two foot, and round two foot diameter grated

inlets. Since the design is modular, non-standard size variations are available at comparable

cost. The modular and scalable portion of the insert is the pan, which houses the strainer and

optional filter. Strainers and filters are offered in a range of sizes to accommodate the basin and

treatment needs. The standard strainer length is 22 inches. To ensure 100% capture of

pollutants and trash, the pan is fitted with hatch style gaskets around the flanged ends. This

design forms a seal between the basin frame, grate, and insert.

Sizing variations are available for inserts based on the storm drain specifications. Included

variations are dual strainer inserts and various strainer depths, as shown in Table 1 on the

previous page.

3.C. The Device maximum trash capture capacity.

See subsection 3.D. for maximum trash capture capacity for standard Storm Clean® filtration

systems.

3.D. The Device hydraulic capacity (flow in cfs) at its maximum trash capture capacity

for all standard Device sizes.

Table 2, below, provides the standard design filtration specifications for typical Storm Clean®

drop inlet filtration units including capture capacity and hydraulic capacity.

Table 2. Storm Clean® standard design filtration specifications

Item No. Description Capture

Capacity (ft3)

Hydraulic Capacity (cfs)

SQ24SED-ll Storm Clean-ll insert complete w/ non-woven sediment element for square 24” drop inlet

1.33 Nominal: 0.089

Max: 0.18

RD24SED-ll Storm clean-ll complete filter insert for round 24”

drop inlet with standard non-woven fabric sediment element.

1.33 Nominal: 0.089

Max: 0.18

RT_x_SED-ll Storm clean-ll complete filter insert for rectangular

catch basin with standard non-woven fabric sediment element. Specified dimensions.

1.33 Nominal: 0.089

Max: 0.18

RD_x_SED-ll Storm clean-ll complete filter insert for round drop

inlet with standard non-woven fabric sediment element. Specified dimensions.

1.33 Nominal: 0.089

Max: 0.18

*NOTE: The trash capture capacity will remain constant with or without the optional filter

element.

8

3.E. Conditions under which the Device re-introduces previously trapped trash.

Trash reintroduction will occur in unit when strainer basket is completely filled and floatable

trash exits through the overflow bypass orifice. The standard overflow orifice is one inch tall by

eight inches wide, and is custom designed accordingly for outgoing pipe capacity.

3.F. Each material and material grade used to construct the Device (stainless steel,

plastic, etc.).

See subsection 3.G. for material and material grade of the components of the Storm Clean®

filtration insert.

3.G. Estimated design life of the Device.

Table 3, below, details the materials and material grades used in Storm Clean® drop inlet

filtration products. The design life of hardware components and filters is dependent on

housekeeping, maintenance, and frequency of catch basin service. The listed design life is rated

for average filter loading, average service frequency, and consistent housekeeping (i.e.

sweeping).

Table 3. Storm Clean® product materials

Item No. Description Material(s) Material Grade Design Life

RPPAN-ll Storm Clean-ll insert pan

with gasket

Stainless Steel or Powder Coated Mild

Steel

Hatch style gasket, 3/8” bulb

#16 304#2B Stainless #14 ASTM A36 Mild

Steel

10 years

3-5 years

RPSTRN-ll Storm clean-ll strainer Stainless Steel or

Powder Coated Mild Steel

# 20 304#2B Stainless #20 ASTM A36 Mild

Steel 10 years

FPSED-ll Non-woven geotextile sediment fabric filter

element

TerraTex N08 nonwoven geotextile

ASTM D4491 1-3 months

FPSEDHC-ll ADsorb-it® oil and

hydrocarbon fabric filter element

ADsorb-it® filtration fabric

ASTM D4491 1-3 months

FPVSAD-ll Storm Clean-ll absorption

filter element with vermiculite

Vermiculite adsorbent media

ASTM C516-08 3-6 months

MPFS-M-ll

Media pack for type-ll Storm clean with 75%

MetalZorb® type M and vermiculite blend

MetalZorb® and vermiculite sorbent

medias

Biodegradable to ASTM D6868

6-12 months

RP4.58ABS Sample port plug 4 5/8"

ABS disc cover New style ABS plastic and

Polyethylene foam ASTM D4673-02 3-5 years

9

3.H. Engineering plans/diagrams for a typical installation.

Engineering plans/diagrams for a typical installation of the Storm Clean® filtration insert are

provided in Appendix A along with the standard dimensions.

3.I. Photographs, if any, of pre- and post-installation examples.

Figures 1 through 6 illustrate the installation process of a Storm Clean® filtration insert, before

and after complete installation. Inserts fit all sizes including but not limited to square, round, and

rectangular basins.

Figure 1. Cleaned drop inlet for Storm Clean® filtration insert

10

Figure 2. Installation of Storm Clean® drop inlet insert with media filter

Figure 3. Installation of Storm Clean® drop inlet insert with fabric filter

11

Figure 4. Installed square Storm Clean® drop inlet insert

Figure 5. Installed round Storm Clean® drop inlet insert

12

Figure 6. Installed rectangular Storm Clean® drop inlet insert

3.J. If the device is designed with an internal bypass, explain how the bypass only

operates with flows greater than the design storm.

During rainfall events that receive flows that are greater than the design storm of a one-year,

one-hour storm in the subdrainage area bypass of the filter can be activated. The bypass of the

filtration unit occurs when flows exceed 0.18 cfs. Bypass is when water flows through the

overflow orifice which is a one inch by eight inch slot located above the level of the strainer. Any

floatable trash that is can fit through the orifice opening will bypass the strainer and will not be

captured.

.

13

4.0 INSTALLATION INFORMATION

4.A. Device installation procedures and considerations.

The specifications detailed in the client worksheet, provided in Appendix B, are used to design

your Storm Clean® drop inlet insert. Installation procedures are described in the steps below.

This information is also provided upon purchase and the delivery of a Storm Clean® insert.

1. Remove grate and thoroughly clean drop inlet basin, grate, and grate support frame. We recommend the host fixture is pressure washed using a vacuum or combination truck.

2. Inspect drop inlet, grate, and frame to ensure the basin is operational. The grate frame should be solid and clean prior to install filtration insert. Any holes or broken sections of the frame will affect the 100% capture seal between the rubber hatch gaskets and frame.

3. MEDIA FILTERS ONLY: Uncouple the snap ring from inside vinyl upper sleeve of the media

filter element.

4. MEDIA FILTERS ONLY: Support the collection pan about 3 feet off ground in a horizontal position.

5. MEDIA FILTERS ONLY: Place the filter element under the collection pan. Bring vinyl upper

sleeve, with the coupling ring, of the media filter up through tapered collar. Start at an open end of snap ring and work the ring around until the ends of the ring can be reconnected.

6. Install the collection pan into the basin. Make sure the rubber gasket on the collection pan has good contact with the grate frame.

7. FABRIC FILTERS ONLY: Install the fabric filter element until it fits snugly into the support

pan opening. 8. Install rigid strainer into the filter element until the strainer is flush with the support pan. This

will be a snug fit. If the strainer does not sit flush, check for obstructions and proper filter installation.

9. Ensure the sample port cap is firmly in place, then reinstall grate.

4.B. Methods for diagnosing and correcting installation errors.

The filtration unit’s modular design reduces installation errors since it is fabricated with the

basins specific specification. The two bullets below are diagnoses for common errors.

A. If grate does fit inside basin: check grate frame connection to determine if insert is properly

installed on grate frame. If grate will not connect to frame, contact the customer support line at

800-723-1373.

B. If strainer doesn’t sit flush with pan: check filter installation, and check for obstructions below

the strainer. If obstructions are present, rotate the pan until strainer sits flush. Contact the

customer service team at 800-723-1373 if you are unable to solve this issue.

14

5.0 OPERATION AND MAINTENANCE INFORMATION

5.A. Device inspection procedures and inspection frequency considerations.

Visual monitoring of the filtration unit to check performance should occur on a monthly basis,

during routine inspection. During the wet season, October through April, the unit should be

inspected after a heavy rainfall event. Inspection of loading can be performed through the grate

to determine whether cleaning is required. To inspect unit performance and status, a tool to lift

grate is necessary (i.e. a grate hook). Observe the capture capacity of the unit’s strainer to

determine if cleaning is required. Check all hardware components to ensure unit is structural

sound with the “Inspection-Maintenance Checklist” provided in Appendix C.

5.B. Maintenance procedures, including a description of necessary equipment and

materials.

Servicing the Storm Clean® drop inlet insert requires a grate hook to access the unit. We recommend using a vacuum or combination truck to accomplish maintenance for safety of operator and 100% containment of pollutants and trash. Utilize the “Inspection-Maintenance Checklist” provided in Appendix C while servicing the unit to ensure all aspects structural aspects of components have been maintained.

1. Remove grate to access the unit for cleaning. 2. Remove and empty the rigid strainer.* This should occur when the strainer is at 75% or

greater capacity to avoid overflow of floatable trash through bypass orifice. 3. Remove filter element.* Filter elements should be changed when the unit is heavily fouled at

the surface and sedimentation has built up, impeding the flow of water. The used filter element should be allowed to drain, and be disposed as solid waste*.

4. Replace filter element with a new one, following the installation instructions.

*Check with your local waste disposal authority for proper disposal of exhausted filter

elements and waste materials removed from the system.

Maintenance is easy with your CleanWay filter; watch a service technician preform maintenance at the following YouTube link: https://youtu.be/3L980PJUyHQ.

5.C. Maintenance frequency considerations, including effects of delay.

Maintenance of the unit should occur at 75% capture capacity. The frequency of this should be

determined during routine monthly inspections of the unit. High Priority Land Use areas with a

history of frequent basin cleaning and litter clean-up will potentially require weekly servicing.

This will depend on whether other BMPs are in place, such as sweeping, litter control, etc.

Delayed servicing and maintenance of the unit will re-introduce trash and debris into the MS4

system.

15

5.D. Device maintenance and vector control accessibility.

The Storm Clean® filtration insert provides easy vector control through the sample port opening,

with access to the sump of the drop inlet. Figure 7 displays where vector control maintenance

can be performed. If the optional filtration component is included in the Storm Clean system, the

vector abatement product can be placed inside the filter element, below the strainer, for periodic

release of insecticide.

Figure 7. Storm Clean® sample port and vector control point of access

16

6.0 RELIABILITY INFORMATION

6.A. Device sensitivity to loadings other than trash (i.e., leaves, sediment).

CleanWay Environmental Partners® has been field testing storm drain filtration units for over 20

years. The company was started in 1995 in the Pacific Northwest, and has worked alongside

environmental service providers to ensure offered products are effective in achieving removal

goals and easily managed by the end user. The smooth design of the strainer will prevent

snagging and catching of leaves and other fibrous debris that has a tendency to stick to rough

surfaces. Sediment will not cause any issues with the removal effectiveness, as any particle

larger than 5mm will entrap inside the strainer. If a filter element is added to the unit, sediment

will accumulate over time, and the filter will need to be replaced. Filter elements contain an

additional 3” sump below the strainer to capture fines that pass through the 3/16” (4.72 mm)

strainer. Replacement schedules depend on the site conditions where the unit is installed. The

general recommended replacement frequency can be referenced in Table 3 of subsection 3.G

on page 8.

6.B. Warranty information.

Warranty information is provided in Appendix D. Upon receiving the Storm Clean® filtration

insert, inspect all components for quality. Notify your sales associate or our customer service

team if any defects are discovered during inspection. Do not install any portion of the insert.

CleanWay does not accept returns on any used filter elements under the manufacturer’s

warranty.

6.C. Applicants customer support.

Customer support is available 8am – 5pm PT at 800-723-1373 or support@cleanwayusa.com.

Feel free to call one of our representatives to answer any questions or concerns.

7.0 FIELD/LAB TESTING INFORMATION AND ANALYSIS

Provide any available field or lab testing information that demonstrates the Device

functionality. If device does not include a 5 mm screen within its design, the applicant

must provide adequate testing that demonstrates it traps trash particles of 5 mms or

more.

The Storm Clean® Filtration System directs all water and particles or trash carried with the

water through a screen with <5mm openings. No particles equal to or greater than 5mm

diameter can physically escape the system unless the system is in bypass. In addition to the set

physical size limitations of the screen, trash collection performance testing is currently being

conducted for further characterization of the system. This information is available upon request

and will be added as an amendment to the application once finalized.

17

APPENDIX A: Standard Drawings for Storm Clean® filtration units

18

APPENDIX B: Client Worksheets

MEASURE YOUR CATCH BASIN

©2016 CleanWay Environmental Partners, Inc. All rights reserved. | 800.723.1373 | info@cleanwayusa.com | cleanwayusa.com

Date: ___________ Email: ___________________________________________

Contact: ______________________________ Phone: _____________________

Company: ________________________________________

Site Address: _____________________________________

Catch Basin Part Number (if applicable) ___________________________

Catch Basin / Grate Measurement Catch Basin / Grate Measurement

A Grate outer diameter F Grate frame height

B Sump depth G Top of outlet to surface grade

C Grate frame inside diameter K Reinforced grate thickness (center)

D Clearance to outlet pipe/baffle L Reinforced grate thickness (edge)

E Grate frame width M Flat grate thickness

Please send any photos of your catch basin and grate to assist with accurate sizing.

Elevation View

Plan View

Check one:

reinforced

or flat

Elevation View

Note any

additional

features

D

MEASURE YOUR CATCH BASIN

©2016 CleanWay Environmental Partners, Inc. All rights reserved. | 800.723.1373 | info@cleanwayusa.com | cleanwayusa.com

Date: ___________ Email: ___________________________________________

Contact: ______________________________ Phone: _____________________

Company: ________________________________________

Site Address: _____________________________________

Catch Basin Part Number (if applicable) ___________________________

Catch Basin / Grate Measurement Catch Basin / Grate Measurement

A Grate width (outside) G Top of outlet to surface grade

B Grate length (outside) H Grate frame height

C Grate width (inside) J Grate frame width

D Grate length (inside frame) K Reinforced grate thickness (center)

E Sump depth L Reinforced grate thickness (edge)

F Clearance to outlet pipe/baffle M Flat grate thickness

Please send any photos of your catch basin and grate to assist with accurate sizing.

Plan View Elevation View

Note any

additional

features

Check one

This page intentionally left blank

19

APPENDIX C: Inspection and Maintenance Checklist

Filter Element

⎕ Replace

⎕ Broken

⎕ Missing

Type(circle): SED / SEDHC / SAD / MetalZorb blend

Notes: ___________________________________________________

Strainer (Mild Steel / Stainless Steel)

⎕ Replace

⎕ Broken

⎕ Missing

Notes: ___________________________________________________

Pan (circle): Round / Rectangular / Square

⎕ Replace

⎕ Broken

Gasket

⎕ Replace

⎕ Missing

Notes: ___________________________________________________

Sample Port

⎕ Replace

⎕ Broken

⎕ Missing

Notes: ___________________________________________________

Site and Catch Basin Location Notes:________________________________________________

______________________________________________________________________________

______________________________________________________________________________

______________________________________________________________________________

Catch Basin

Type(circle): Round / Rectangular / Square

⎕ Repair

⎕ Broken

Notes: ___________________________________________________

Grate

⎕ Replace

⎕ Broken

⎕ Missing

Notes: ___________________________________________________

Inspection-Maintenance Checklist

Name: _______________________________________

Date:_________________________________________

Company: ____________________________________

CleanWay Environmental Partners, Inc. | cleanwayusa.com | 800.723.1373 | info@cleanwayusa.com

20

APPENDIX D: Product Warranty

www.cleanwayusa.com

CleanWay Environmental Partners Inc. | PO Box 30087 | Portland, OR 97294 | 800.723.1373 | Fax: 503.288.3658

CleanWay Limited Product Warranty Statement

Extent of Limited Warranty CleanWay Environmental Partners Inc. (CleanWay) warrants to the end-user customer that CleanWay products will be free from defects in material and workmanship for a period of one year (12 months).

CleanWay does not warrant that the operation of any product will be uninterrupted or error free.

CleanWay’s limited warranty covers only those defects that arise as a result of normal use of the product and does not cover any other problems, including those that arise as a result of: (i) improper installation, maintenance or modification; (ii) media, parts or supplies not provided or supported by CleanWay; (iii) operation outside the product’s specifications; or (iv) unauthorized modification or misuse.

If CleanWay receives, during the applicable warranty period, notice of a defect in any product which is covered by CleanWay’s warranty, CleanWay shall either repair or replace the product, at CleanWay’s option.

CleanWay shall have no obligation to repair or replace until the customer returns at their expense the defective product to CleanWay.

The customer shall be responsible for any shipping and handling charges incurred in delivery of products covered under warranty.

Any replacement product may be either new or like-new, provided that it has functionality at least equal to that of the product being replaced.

CleanWay replacement products may contain remanufactured parts, components, or materials equivalent to new in performance.

CleanWay’s Limited Warranty Statement is valid in any country where the covered CleanWay product is distributed by CleanWay.

Limitations of Warranty TO THE EXTENT ALLOWED BY LOCAL LAW, NEITHER CLEANWAY NOR ITS THIRD PARTY SUPPLIERS MAKES ANY OTHER WARRANTY OR CONDITION OF ANY KIND, WHETHER EXPRESS OR IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, SATISFACTORY QUALITY, AND FITNESS FOR A PARTICULAR PURPOSE.

Limitations of Liability To the extent allowed by local law, the remedies provided in this Limited Warranty Statement are the customer’s sole and exclusive remedies.

TO THE EXTENT ALLOWED BY LOCAL LAW, EXCEPT FOR THE OBLIGATIONS SPECIFICALLY SET FORTH IN THIS WARRANTY STATEMENT, IN NO EVENT SHALL CLEANWAY OR ITS THIRD PARTY SUPPLIERS BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, WHETHER BASED ON CONTRACT, TORT, OR ANY OTHER LEGAL THEORY AND WHETHER ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.