E-7

Hand strap eyelet

Mode dial

Aperture / Exposure compensation button

Live View shooting / Movie shooting button (*1)

AE lock / FE lock / Index / Reduce button

AF point selection /Magnify button

Rear case

Main dial

Shutter lever

Buckle

Buckle lock lever

Hand strap eyelet

Menu buttonShooting settings display button

Tripod socket (bottom)

AF mode selectionbuttonSetting button

WB selection button

L-hookViewfinder

Playback buttonDrive mode selection button

Erase button

Front case Port lock

Port mount ring

Focus / Zoom dial

Accessory shoeFiber-optic cable socketPower switch

*1: It is not be used with EOS REBEL T1i / EOS 500D camera.*2: It controls the Live View shooting / Movie shooting button of the EOS REBEL T1i /

EOS 500D camera.

Picture Style selection buttonPressure balance control valve

Quick control button (*2)

Identification of Parts

YS converterconnector

Buckle

Buckle locklever

E-12

The "Quick Control button" on the rear case of this product controls the [Live View shooting/ Movie shooting button] of the REBEL T1i / 500D camera. Please place the provided Live View button sticker on the "Quick Control button".

Place the Live View button sticker on the "Live View shooting/Movie shooting button" when using the REBEL T2i / 550D camera.

Live View button sticker

Live View button sticker

(Red)

Preparation for Setting Up

Eliminate any old stains before placing the sticker on the product.

Live View shooting/Movie shooting buttonPlace sticker

Place sticker

Invalid

Quick Control button ( )

1E-14

OPEN

LOCK

Convex part

Concave part

Convex part

Concave part

2 Align the convex part of the Port with the concave part of the port mount ring, and fully insert the port into the housing

CAUTION

Attaching and Detaching the Port

Release the port lock on the RDX housing (front case) by sliding it in the direction of the arrow as shown in the diagram, and rotate the port mount ring toward OPEN (in a counterclockwise direction) until it stops

Before attaching the port, make sure there are no specks of dust, scratches, or deformities on the O-ring and the O-ring contact surfaces.

Port lock

Slide

CAUTIONOnly the optional ports designed for SEA&SEA RDX-series housings can

be attached to this product.This product is delivered with a housing body cap attached to the port mount.

Make sure to remove the housing body cap when attaching the port.The housing body cap has no watertight capability.When attaching the port to the housing, always refer to the instruction

manual provided.

Attaching the port

In order to use this product underwater, the optional port for the camera lens must be attached to this product.

E-17

Pop up the camera's built-in flash. Align the camera tray with the camera base inside the front case, and slide the camera forward into the front case

Make sure to pop up the built-in flash of the camera before mounting the camera in the housing. Once the camera has been mounted, the flash button of the camera cannot be used, and the camera's built-in flash cannot be popped up. Make sure the camera tray is inserted

all the way into the camera base until it stops.Make sure that the camera tray is

properly placed and the knob is locked.

Mounting the Camera in the Housing

6

Pull the power switch and focus/zoom dial out

Make sure that the O-ring is properly fitted in the O-ring groove before setting of the rear case.

8 Place the rear case on the front case, and close the buckles

See:Opening and Closing the Housing (P. E-13)

Align the lever of the housing's power switch and the camera's power switch

7

After the camera is mounted in the housing, make sure to check that all of the housing's control parts work properly and the camera functions correctly.

CAUTION

5

Power switch

Lever

E-22

With the YS converter (option)Connect the strobe with the YS converter (option) when the strobe is triggered in conjunction with the camera.

Align the round mark (or the notch on the tip) of the connecting cable with the round mark (or the convex part inside) of the strobe bulkhead, and then push it straight in

Remove the connector cap from the YS converter connector

Make sure there are no scratches or debris on the O-ring of the connecting cable being connected

1

2

3

Carefully observe the instruction manual for the YS converter before use.A Grip-stay L (option) is required when using the YS converter.Do not connect the strobe and the YS converter connector with a sync cord

(option) because this will damage the YS converter connector.

CAUTION

Connecting cableYS converter connector

Connecting the Strobe

E-26

External Controls

Quick control buttonIt controls the Live View shooting / Movie shooting button of the EOS REBEL T1i / EOS 500D camera.

Live View shooting / Movie shooting buttonIt is not be used with EOS REBEL T1i / EOS 500D camera.

Other controls

Other control parts on the housing correspond to the operation parts of the digital camera. Refer to the camera's instruction manual for details of each function.

CAUTIONAfter mounting the camera in the housing, make sure to check that all of

the housing's control parts work properly and the camera functions correctly before underwater use.

E-30

Release RubberLive View button stickerSilicone greaseO-ring remover Attachment toolHand strapO-ring maintenance manualInstruction manual (this manual)Mounted accessories to the product :Housing body capFiber-optic cable socket cap (x2)Converter connector cap

The specifications and appearance are subject to change without notice.

Canon EOS REBEL T1i / EOS 500DCanon EOS REBEL T2i / EOS 550D

Body: Polycarbonate resin (Black)

60 m (200 feet)

Approx. 200 (W) 190 (H) 139.5 (D) mm (14.2 8.8 6.0 inches)

Approx. 2000 g (4.4 lbs.) (housing only)

Compatible camera

Controls

Construction

Depth rating

Dimensions

Weight

Accessories

Power switch, Main dial, Shutter lever, Focus / Zoom dial, Mode dial, AE lock / FE lock / Index / Reduce button, AF point selection / Magnify button, Live View shooting / Movie shooting button(* 1), Aperture / Exposure compensation button, Quick control button(* 2), WB selection button, AF mode selection button, Setting button, Erase button, Picture Style selection button, Playback button, Drive mode selection button, MENU button, Shooting settings display button

*1: It is not be used with EOS REBEL T1i / EOS 500D camera.*2: It controls the Live View shooting / Movie shooting button of the EOS REBEL T1i /

EOS 500D camera.

Specifications