Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
R&D BANDSAWSManufacturer of TUFF TOOTH® Blades
Information: (905) 840-0399
Order Desk: 1-800-461-3895
www.tufftooth.com
“Over 45 Years of Experience - Quality, Knowledge & Value”
Introduction
R&D Bandsaws is a Canadian company located in Brampton, Ontario. We are a mail order company and have
a retail store. We carry additional products not found in this catalogue. Visit our store or website for our complete
range. All prices listed in this catalogue are in Canadian funds. Prices are in effect July 1, 2018 and supersede
those previously published. While we make every attempt to verify published prices, an incorrect price may be
inadvertently printed. Refer to our website for current prices. All prices are subject to change without notice. See
our order form (on page 27) for shipping rates, sales tax, etc.
Radius Selection Chart
R&D Bandsaws specializes in bandsaw blades made to order. Coilstock
is available if you prefer to make your own blades (the Sure-Splice Kit
will help make this job easier). For maximum strength and rigidity, we
recommend using the widest bandsaw blade possible. For example,
when cutting a curve with a 2" radius, a 3/8" blade would be the best
choice (see our Radius Selection Chart).
*Radius Chart diagram is not to scale.
Blade Speed
The blade speed for cutting metal is much slower than the blade speed for cutting wood. Wood cutting blade
speed is between 2000 and 4000 FPM. Non-ferrous metal cutting blade speed is between 700 and 1000
FPM. Metal cutting blade speed is between 85 and 200 FPM. To calculate blade speed: Motor RPM x Pulley
divided by Upper Wheel Pulley x Wheel Diameter x 3.1416 divided by 12 = LFPM. You can also calculate
blade speed by marking the wheel, turning the motor one revolution, measuring the distance from the mark
and multiplying by the motor RPM.
Weld Guarantee
R&D Bandsaws guarantees the blade weld. If a blade breaks at the weld, return it by mail to R&D Bandsaws
and it will be repaired and returned at no charge. This guarantee does not apply to blades under 71” in length
or 3-wheel blades. The return shipping cost will be the responsibility of the customer. The customer will not
be refunded for the return shipping cost.
How to Calculate Blade Price
Multiply the blade length by the price per inch. For the length, always round up to the closest half inch. For
example when ordering a Carbon blade 93 1/2" long by 1/4" wide, multiply 93.5 x 14¢ (price per inch) for a
total of $13.09. When ordering blades please indicate the type of machine (2 or 3 wheel), blade length,
width, tooth style and TPI (teeth per inch).
Information
www.tufftooth.com2
Industrial Silicon
The Industrial Silicon band has three to four times the blade life of a normal carbon band. This band is made
with tungsten silicon chrome alloy added to carbon steel. This gives the blade a harder tooth and the ability
to withstand higher temperatures before they are effected by heat. It requires less tension to cut straight. All
blades have milled teeth to give them a uniform tooth and a much sharper tooth, which means a smoother
finish. The best choice for resawing is the 1/2" x 3TPI. This blade performs like a much wider blade using
only half as much power; therefore, this is ideal for a saw with less than 1 HP.
Width Thickness Standard TPI Hook TPI Skip TPI Per Inch
1/8” .025” 14 - - 20¢
3/16” .025” 10 - 6 20¢
1/4” .025” 10 4, 6 - 20¢
3/8” .025” - 3, 4, 6 - 20¢
1/2” .025” - 3, 4 - 20¢
3/4” .032” - 3 - 23¢
1” .032” - 2, 3 - 23¢
*Industrial Silicon blades less than 72” ....................................$12.50
Swedish Silicon
The Swedish Silicon band has three to four times the blade life of a normal carbon band. They have a five
tooth pattern with minimal set. Every fifth tooth is a straight raker, with a 6.5º hook angle that gives it an
incredible fast cut and smooth finish.
Width Thickness Standard TPI Hook TPI Skip TPI Per Inch
1/8” .025” 14 - - 20¢
3/16” .025” 10 - 6 20¢
1/4” .025” 10 4, 6 - 20¢
3/8” .025” - 3, 4, 6 - 20¢
1/2” .025” - 3, 4 - 20¢
3/4” .032” - 3 - 23¢
1” .032” - 2, 3 - 23¢
*Swedish Silicon blades less than 72” ....................................$12.50
2-Wheel Flexible Back
This is a heavy-duty industrial carbon blade. It is a durable commercial grade bandsaw blade for novice or
industrial woodworking and metalworking. Used for hard and soft wood, plastic, non-ferrous metal and mild steel
(for machines with speed reduction). Use with all stationary 2-wheel bandsaws.
Width Thickness Standard TPI Hook TPI Skip TPI Per Inch
3/16” .025” 10 - 4 14¢
1/4” .025” 8, 10, 14, 18 4, 6 4, 6 14¢
3/8” .025” 8, 10, 14, 18 3, 4, 6 3, 4, 6 14¢
1/2” .025” 6, 8, 10, 14, 18 3, 4 ,6 3, 4, 6 14¢
3/4” .032” 6, 10, 14 2, 3, 4 3 16¢
1” .035” 4, 6, 8, 10 1.33, 2, 3, 4, 6 3, 4 16¢
*2-Wheel Flexible Back blades less than 72” ............................$9.25
Bandsaw Blades
Order Desk: 1-800-461-3895 3
Buy 3 or moreSilicon blades of
the same length fora 15% discount!
Buy 3 or moreSilicon blades of
the same length fora 15% discount!
Little Ripper Blade
When resawing or cutting straight, we recommend our Little Ripper
Blade. This 5/8”x.025”x3TPI or 4TPI high tungsten impregnated silicon
blade will make the cut cleaner and faster than a regular bandsaw
blade. Extra hard, stays sharp and cuts straight. It is extra wide to add
stiffness to the blade, has a thin kerf and cuts extremely smooth. Price
below is for any length up to 150”.
Width Thickness TPI Price
5/8” .025” 3, 4 $36.00
Woodslicer Swift
With a 3-4 variable pitch, this blade has the aggressiveness of a 3
tooth and a surface finish of a 4 tooth. It creates a quick, quiet and
clean cut time after time. The bright finish reduces friction. This is a
wood slicer blade (not for green wood). The Woodslicer Swift is a
must try! Price below is for any length up to 150”.
Width Thickness TPI Price
5/8” .025” 3-4 $36.00
3/4” .025” 3-4 $36.00
Ripper37
Precision ground, hard tooth, ultimate performance bandsaw blades. 37%
longer lasting. Fast, straight, precise cuts. Razor sharp teeth. Improved
finish of sawn product.
Width Thickness TPI Per Inch
1/4” .025” 6 16¢
3/8” .025” 3, 4 16¢
1/2” .025” 4 16¢
3/4” .032” 2, 3 20¢
1” .035” 1.3, 2 22¢
1 1/4” Millband .035” 1.1, 1.3 23¢
1 1/4” Millband .042” 1.1, 1.3 23¢
Bi-Metal (Wood Cutting)
This blade has teeth with higher heat and wear resistance than carbon
bands, giving it higher production rates and improved band life. It is
used for cutting hard or abrasive materials.
Width Thickness Hook TPI Per Inch
1/4” .025” 6 40¢
1/2” .025” 3 40¢
3/4” .032” 3 40¢
Bandsaw Blades
www.tufftooth.com4
Furniture Band (Carver & Woodturner Band)
With a .032” blade thickness, this blade has increased beam strength,
great fatigue and wear resistance. It has an extra-wide kerf designed
to help cut the wet stringy fiber found in green wood. Great blade for
woodturners or carvers for roughing out blanks where a smooth finish
is not required. Cannot be used on saws with wheels smaller than 12”.
Width Thickness TPI Per Inch
1/4” .032” 3, 4 18¢
3/8” .032” 3, 4 18¢
1/2” .032” 3, 4 18¢
Carbon Millbands
This high quality carbon steel millband has large hook teeth. It has
great chip clearance.
Width Thickness Hook TPI Per Inch
1 1/4” .035” 3/4, 7/8 20¢
1 1/4” .042” 3/4, 7/8 21¢
Meat Band
Hard tooth, bright steel bandsaw used mainly in the food industry. The
sharp, hook type teeth allow maximum penetration and ease of cutting,
whilst the light set amount on the teeth reduces waste.
Width Thickness TPI Per Inch
1/2” .020” 4 20¢
5/8” .020” 4 20¢
3/4” .020” 4 20¢
3-Wheel (Bench Top Flexible)
A heavy duty, durable commercial grade bandsaw blade. For a smaller
bandsaw, these blades produce better performance, accuracy and
stability due to their thinner gauge. Used for hard and soft wood, plastic
and non-ferrous metal (for machines with speed reduction).
Width Thickness Skip TPI Per Inch
1/4” .020” 4, 6 18¢
3/8” .020” 4, 6 18¢
1/2” .020” 4, 6 18¢
Bandsaw Blades
Order Desk: 1-800-461-3895 5
Metal Cutting Carbon Flexible Back
This is an economical, high quality carbon steel bandsaw blade for
general-purpose cutting. Hard teeth and a flexible back ensure long
cutting life on mild and low alloy steels and plastics.
Width Thickness Raker TPI Per Inch
1/8” .025” 14 14¢
3/16” .025” 10 14¢
1/4” .025” 10, 14, 18, 24 14¢
3/8” .025” 8, 10, 14, 18, 24 14¢
1/2” .025” 6, 8, 10, 14, 18, 24 14¢
3/4” .032” 6, 10, 14, 18 16¢
1” .035” 6, 8, 10, 14 16¢
*Metal Cutting Carbon Flexible Back blades less than 72”........$9.25
Bi-Metal (Metal Cutting)
Bi-Metal Blades are manufactured from the finest matrix strip, electron
beam welded onto a very tough and flexible backing material. The
choice of matrix H.S.S. edge provides shock resistance required for
interrupted cutting, such as bundle cutting and structural steels. Highest
resistance to tooth chippage with a rugged backing providing long
service life with vibration prone sawing.
Width Thickness Raker TPI Variable Pitch Per Inch
1/2” .025” 14 10/14 40¢
3/4” .035” 14 4/6, 5/8, 6/10, 8/12, 10/14 40¢
1” .035” - 3/4, 4/6, 5/8, 6/10 42¢
Bandsaw Blades
www.tufftooth.com6
Coilstock
Make your own blades with our coilstock (and Sure-Splice Kit sold seperately). Prices are per foot. Minimum
order of 20 feet per width.
Material 1/8” 3/16” 1/4” 3/8” 1/2” 5/8” 3/4” 1” 1-1/4”
Silicon $1.98 $1.98 $1.98 $1.98 $1.98 - $2.28 $2.28 -
Carbon - $1.39 $1.39 $1.39 $1.39 $1.49 $1.58 $1.58 -
3-Wh/BT - - $1.78 $1.78 $1.78 - - -
Furn Band - - $1.78 $1.78 $1.78 - - - -
Meat Band - - - - - $1.98 - - -
Bi-Metal - - - - $3.96 - $3.96 $4.16 -
Scallop/KnifeEdge - - - - - $2.20 - - -
Carbon Millband (.035”) - - - - - - - - $1.98
Carbon Millband (.042”) - - - - - - - - $2.08
Sure-Splice Kit
This simple jig will position bandsaw blades for silver soldering so you can make and repair your own blades.
It uses high strength silver solder which means that no expensive welding equipment is needed. All that is
required is a propane torch, file or grinder and coilstock to make the blades. Adjustable for blade widths from
1/16" to 1-1/4". Includes plans for a blade-grinding jig that will make it easy to grind accurate bevels on the
blade. The Sure-Splice Kit contains the Sure-Splice jig, solder and flux for about 30 blades. The Refill Kit
contains enough solder for approximately 150 small splices.
Sure-Splice Kit ..........................................................................$43.95
Silver Solder and Flux Refill Kit ................................................$30.95
Coilstock
Order Desk: 1-800-461-3895 7
Replacement Guide Blocks
Graphite impregnated phenolic blocks are designed to replace the
metal guides that came with your bandsaw. They extend blade life,
reduce heat and noise. Longer in length to give you extra value and
can be set closer to the blade for better accuracy and control. These
are a must when using 1/8" blades. Four pieces per set.
Item# Machine Price
D14 14” Delta $11.00
IM14 14” Import or General (4 square) $11.00
IMR14 14” Import (2 round, 2 square) $11.00
G14 14” General Int. 90-150M1 $11.00
IM4R 15” Import (4 round) $11.00
D3WM16 16” Delta or 12” Rockwell $11.00
S12 12” Sears or 10” Delta $11.00
D10 10” Delta (new) $11.00
BT9 9” Two-Wheel $11.00
BT810 8”/10” Bench Top (56 1/8") $11.00
RB1415 to replace roller bearings* $19.95
*Fits 14” & 15” bandsaws (Delta/General/King/Toolex/Trademaster)
Replacement Guide Block Holder
Made to fit all 14" Import and Delta bandsaws to hold a 1/2" square
guide block. It is important to have these in premium working order to
help prevent sideways movement and wandering to increase accuracy
and decrease wear on the blade.
Replacement Guide Block Holder..............................................12.95
Zero Clearance Table Insert
Made of special high density plastic designed to eliminate small
pieces of wood from falling below the table and into the wheels. Also
helps control the amount of sawdust that collects on top of the table
and provides total support on both sides of the blade during cutting.
Size Machine Price
2 1/4” 14”/15” General $4.95
2 1/2” 12”/14”/16” Delta, 14” Imports $4.95
2 3/4” 17” Imports & General Int. 90-150M1 $4.95
Three of the same type $11.00
Parts & Accessories
www.tufftooth.com8
Rubber Tires (for 14” & 15” machines)
Worn or cracked rubber tires prevent proper blade tracking. Our
replacement tires meet manufacturer's specifications for all 14” and
15” bandsaws. They have been mad e 30% smaller to assure a tight fit
and easy installation, as they are not required to be glued to the
wheel. Sold as a pair.
Rubber Tires (pair)....................................................................$29.95
Neoprene Tires (for 14” machines)
Thin, seamless neoprene rubber conforms to machined crown. More
resistant to oil and other harmful chemicals. Easy to install (place in
hot water until soft then stretch on and let cool). For 14” bandsaws
with raised rims on edge of wheels. Sold as a pair.
14” Neoprene Tires (pair) ........................................................$34.95
Neoprene Tire (for 17” machines)
Thin, seamless neoprene rubber conforms to machined crown. More
resistant to oil and other harmful chemicals. Easy to install (place in
hot water until soft then stretch on and let cool). For 17” bandsaws
with raised rims on edge of wheels. Sold individually.
17” Neoprene Tire (each) ........................................................$34.95
Rubber Tire Material
Have an odd size wheel? Make your own rubber tires! 1/8” thick,
70 duro neoprene. Available in 11mm, 1/2”, 5/8”, 3/4”, 1”, 1-1/8”,
1-1/4” and 1-1/2” wide. Can be glued with cyanoacrylate or contact
cement. Material must be scuffed before being glued to the wheel.
Rubber Tire Material......................................................$3.50 per foot
Parts & Accessories
Order Desk: 1-800-461-3895 9
Upper Wheel Sliding Bracket, Knob & Nut
For 14” Imports only.
Upper Wheel Sliding Bracket, Knob & Nut ..............................$36.95
High Tension Spring
15% more material per inch for longer life. Less deflection with increased
blade tension. Eliminates barrel cut common with insufficient tension. Fits
all 14” bandsaws. Available in 2 1/2” and 3” length. Please specify
length upon ordering.
High Tension Spring ................................................................$16.95
Blade Tension Speed Crank
No one likes being under stress yet that is how we leave our bandsaw
if we don’t back off the blade tension. Factory supplied knobs are a
headache to turn so most of us don’t do it. This easy to use crank takes
the headache out of blade tensioning. Quickly crank up the tension before
use and crank down the tension when finished. Fits all 14” bandsaws.
Blade Tension Speed Crank ....................................................$29.95
Upper Wheel Shaft Hinge & Nut
For 14” Imports only.
Upper Wheel Shaft Hinge & Nut ..............................................$28.95
Trunnion
Made for 14” bandsaws, this mechanism allows the table to be set on an
angle. This makes for a variety of beveled or angled cuts possible. After
the table is adjusted to the desired angle, it is locked in place with the
trunnion lock.
Trunnion ..................................................................................$19.95
Parts & Accessories
www.tufftooth.com10
Table Pin
The Table Pin corrects the misalignment of the table. It is a must have
as it is often misplaced.
Table Pin ....................................................................................$7.95
Thrust Bearing
Maintaining thrust bearings in good working order prevents backward
movement of the bandsaw machine that could result in misalignment
and/or damage to your blade. These bearings have a pressed fit seal
to provide a longer life, and are manufactured to fit most 14" bandsaws
(King, Toolex, TradeMaster, Delta and many imports). Sold individually.
#6200 Thrust Bearing ................................................................$7.95
Upper Wheel Bearing
Replace bearings when they begin to show signs of wear or make
noise. These bearings meet or exceed manufacturer's specifications. For
best results, replace in pairs. Made for most 14" bandsaws. Sold individually.
#6202 Upper Wheel Bearing ......................................................$7.95
Replacement Phenolic for Guide Bearings
These are to replace the bearings that came with your bandsaw. Designed
to run in contact with the blade, to lubricate and allow you to have full
control of the blade, they remain stationary. Can be used with blades from
3/32” to 1-1/4” wide. Four pieces per set. If your bearings are not listed,
please contact us with your bearing number and we will try to accommodate.
Item# Machine Price
608 Bandsaws using 608 bearings $19.95
628 Bandsaws using 628 bearings $19.95
6200 Bandsaws using 6200 bearings $19.95
6201 Bandsaws using 6201 bearings $19.95
CX104 14” Craftex CX104 $19.95
Coplanar Kit
Consists of special spacers used to adjust the alignment of both the
upper and lower wheels. Greatly improves blade control and accuracy
in cutting, while decreasing the wear and tear on your blade. Includes
both 5/8" and 3/4" openings to fit both the upper and lower wheel
shaft. Includes four 5/8" spacers and four 3/4" spacers.
Coplanar Kit ................................................................................$4.95
Parts & Accessories
Order Desk: 1-800-461-3895 11
Blade Lubricant
Prolongs blade life and produces smoother and quicker cuts. Specially
compounded to keep metal, plastic and wood cutting blades from
clogging with wood chips or pitch. Use on all power and hand held
cutting tools including bandsaw, scroll, circular, hack and jewelers saw
blades. Measures 8”x1”.
Blade Lubricant ........................................................................$12.95
Finishing Stone
For improved finish and blade performance. Lay the side of the wood
handle on the table surface and place the silicon carbide stone
against the back of the blade to round off the edges. No lubricant
needed. Permits tighter radius cutting. Prevents excessive wear on
thrust bearings. Provides a smoother finish on the workpiece during
radius cutting. Removes mushrooming on back of blade caused by
pressure against thrust bearings.
Finishing Stone ........................................................................$17.95
Anti-Vibration Link Belt
1/2” wide, super flexible drive belt greatly reduces the transfer of
vibration with all woodworking machines. Unlike a rubber belt, which
will take the shape of the small diameter pulleys that are used on most
woodworking machines, the individual link on this drive belt keeps it
flexible for life. Very easy to use and can be adjusted to any length.
Anti-Vibration Link Belt ................................................$9.95 per foot
Toggle Safety Switch
If you own stationary woodworking machines, odds are at least one of
them has this switch on it. Are you having trouble with it? Sometimes
it takes a second click of the switch to get the tool to start? You’re not
alone. They are a great little switch but they were not designed to last
forever. By popular request, we’ve brought this one into stock. It’s a
double pole double throw switch rated 19 amps at 125 volt and 12 amps
at 250 volts. The removable yellow tab is an excellent child safety lockout
and the side shields prevent accidental activation. Don’t put off changing
that faulty power tool switch any longer.
Toggle Safety Switch..................................................................$5.95
Parts & Accessories
www.tufftooth.com12
Starter Kit
The Starter Kit includes a 1/2”x3TPI Industrial Silicon bandsaw blade,
a 1/4”x6TPI Industrial Silicon bandsaw blade, a set of replacement
guide blocks, a finishing stone, a zero clearance table insert and two
rubber tire cleaner pads.
Starter Kit (for a 14” Delta and/or Import) ................................$52.95
Starter Kit (for a 15” Import w/Riser and/or General ................$56.95
Heavy Duty Tune Up Kit
The Heavy Duty Tune Up Kit is specifically put together for 14” Import’s
and/or Delta’s. It includes two thrust bearings, a high tension spring, a
zero clearance table insert, a set of neoprene tires, a coplanar kit and
set of replacement guide blocks. When ordering, please specify whether
your machine is a Delta or an Import.
Heavy Duty Tune Up Kit ..........................................................$65.95
Double Sided Tape
Our 33mx18mm (approximately 1300”x3/4”) double sided tape is ideal
when cutting through more than one piece of wood. It holds pieces
firmly together and enables accurate cutting.
Double Sided Tape ....................................................................$8.95
Utility Brush Set
Use these utility brushes to apply stain, stripper, glue, acid or even a
dab of paint! 50 brushes per bag.
Utility Brush Set ..........................................................................$9.95
The New Complete Guide to the Band Saw
by Mark Duginske
This essential guide to woodworking's most versatile tool includes a
thorough analysis on everything needed to know in order to purchase,
setup, use, and maintain a band saw. This book details what wood-
workers need to know before purchasing a saw--including the eight
questions to ask before buying a used saw--along with topics such as
a part-by-part overview of every component of the saw, techniques of
set-up and alignment, choosing the right blade, and understanding
hand positioning to provide any woodworker with the most complete
guide to a band saw. Special sections are devoted to band saw
accessories, how to deal with common problems, and how to maintain
a band saw to keep it running effectively and efficiently for years.
The New Complete Guide to the Band Saw ............................$22.95
Parts & Accessories
Order Desk: 1-800-461-3895 13
Circle Jig Kit
This jig provides the only sure way of cutting perfect circles with fewer
hassles than any other method. Homemade circle jigs provide adjustment
of the circle diameter only. They also fail to provide a means to feed
the work into the blade for the starting cut so the work must be rough
cut very close to the finished size (it is like having to make the cut
twice). This jig cuts circles from 2”-24” in diameter and fits on any
bandsaw with a 3/8”x3/4” miter slot. It even lets you tilt the table to cut
circles with a beveled edge. Includes all hardware and plan (excluding
the board).
Circle Jig Kit ............................................................................$33.95
The Little Ripper
The Little Ripper sled unit is used in conjunction with a sliding table with
track. You will purchase this if you already have the sliding table unit
which attaches to your bandsaw. The Little Ripper is a Canadian-made
product which is simple and easy to use. It holds a log securely in place
while you guide it through a bandsaw blade. A distinct quality about
this tool is that it serves a dual purpose. Simply by turning this jig 180º,
you have transformed your mini-sawmill into a valuable fence. The Little
Ripper is an essential and practical tool for every workshop. The Little
Ripper Height Extension is included.
The Little Ripper ..................................................................$239.00*
*Actual shipping charges will apply.
Mule Bandsaw Fence
The Mule Bandsaw Fence brings a new level of accuracy to your
bandsaw. The front guide bar is 24" long yielding plenty of rip capacity
on both sides of the blade. Due to various thickness of table tops, we
provide adapters with every system. If ripping or re-sawing is in your
bandsaw's future, you owe it to yourself to own a Mule Bandsaw
Fence. The Mule resaw guide is included.
Mule Bandsaw Fence ..........................................................$139.00*
*Actual shipping charges will apply.
Parts & Accessories
www.tufftooth.com14
Aluminum Mitre Track
4’ long with 3/8” x 3/4” inside dimensions.
#44166 Aluminum Mitre Track ................................................$18.95*
*Pick up only.
Aluminum T-Track
This aluminum extrusion is one of the most useful components for
making jigs and fixtures. Sized to fit 1/4-20 hardware, it can be used
with T-slot nuts or T-bolts. 4’ long with 3/8” x 3/4” outside dimensions.
#44162 Aluminum T-Track ......................................................$13.95*
*Pick up only.
Self-Adhesive Tape Measure
This 10’ long by 3/4” wide, self-adhesive tape measure can be applied
to table saws, bandsaws, radial arm saws, etc.. SAE / Metric. Metallic
tape is highly scuff resistant and can be trimmed to length with
scissors. Be sure when ordering to choose the correct tape orientation.
#28394 Self-Adhesive Tape Measure (reads left to right) ..........$3.95
#28396 Self-Adhesive Tape Measure (reads right to left) ..........$3.95
Feather Board
Great for ripping long pieces of narrow stock or moulding. Fits into
your 3/4" mitre gauge slot, then locks easily into position with the twist
of a butterfly nut. Puts pressure on top and against stock, preventing
kickback, rideup and inaccuracy.
Feather Board ............................................................................$9.95
3-Point Knob
Made from durable plastic with a 1/4-20 thread. Measures 1-3/16”.
3-Point Knob..................................................................................99¢
5-Point Knob
Made from durable plastic with a 1/4-20 thread. Measures 2”.
5-Point Knob..................................................................................99¢
Parts & Accessories
Order Desk: 1-800-461-3895 15
T-Handle Vertical Toggle Clamp 200lb
Item# Bolt Overall Height Overall Length Bar Height Bar Length Price
50820 Small 3.1” 2.6” 1.38” 2.28” $7.95
Vertical Toggle Clamps
Item# Size Price
50825 200lb $7.95
50827 500lb $7.95
50828 500lb $9.95
50829 750lb $13.95
Horizontal Toggle Clamps
Item# Size Price
50835 200lb $7.95
50837 500lb $7.95
50839 750lb $13.95
Push-Pull Clamp 300lb
Item# Overall Height Overall Length Bar Height Bar Length Price
50844 3.3” 5.46” 1.14” 3.3” $9.95
Push-Pull Clamp 500lb
Item# Overall Height Overall Length Bar Height Bar Length Price
50845 4” 4.9” 1.25” 2.8” $9.95
Latch Clamp 700lb
Item# Overall Height Overall Length Bar Height Bar Length Price
50847 1.6” Adjustable N/A Adjustable $7.95
Hold-Down Bolts
Flat cushion tip. Complete with flanged washers and nuts.
Item# Size Price
50850 Small (fits 50825) $1.50
50853 Medium (fits 50827) $2.25
50855 Large (fits 50829) $2.25
Clamps
www.tufftooth.com16
Quality and value are two standards that R&D Bandsaws takes very seriously. We wouldn’t put our name on
just anything, which is why we have searched high and low and have found a Carbide Tipped blade that exceeds
all our expectations. In fact, we are so confident in the quality of the manufacturer product that we have put
our name on it. These Canadian made Industrial blades are the solution to any woodworking challenge you
may have; each blade has been designed to meet specific applications. The individual models have been
developed with its own specific grade of material, cutting geometry and operational enhancements. Each are
fully balanced with a stress relieved plate, making the need for stabilizers unnecessary. R&D Bandsaws is continually
committed to offering products of quality at great value to meet the challenges of any woodworking product.
***Resharpening services available, contact for pricing!***
Rip Saw (10” x 40T A.T.B.)
For ripping operations on soft and hardwoods.
10” x 40T A.T.B. Rip Saw ........................................................$73.95
Combination Multipurpose Cut (10” x 50T)
For ripping or cross cutting solid woods, particle board, plywood and
laminated panels.
10” x 50T Combination Multipurpose Cut ................................$76.95
Standard Cross Cut (10” x 60T A.T.B.)
For regular cutting of wood, plywood, particle board and laminated veneer.
10” x 60T A.T.B. Standard Cross Cut ......................................$77.95
Cross Cut (10” x 80T T.C.G.)
Gives the finest cut on plastic laminated boards, laminated plywood-
chipboard, arborite, formica and other plastic materials.
10” x 80T T.C.G. Cross Cut ......................................................$94.95
Carbide Tipped Blades
Order Desk: 1-800-461-3895 17
Mach Speed
5” long, plain end with reverse teeth that cut on the upstroke and minimize
underside tearout. Precision milled blades with wide spaced, ultra sharp
teeth for fast, accurate cuts in hard and soft woods. Widely spaced
gullets minimize burning and provide rapid chip removal. Position blade
with reverse teeth in bottom blade holder. 2 – 5 teeth should appear
above the table surface to score the work piece on the upstroke. Adjust
feed pressure to prevent burning.
Item# Univ# Width Thick TPI/Style Blister(12) Gross
643M 3R .032" .014" 13/7 Skip $6.95 $62.95
645M 5R .038" .016" 13/7 Skip $6.95 $62.95
647M 7R .046" .017" 8/6 Skip $6.95 $62.95
649M 9R .055" .018" 8/6 Skip $6.95 $62.95
PGT Precision Ground Tooth
PGT® Scroll Saw Blades are the best blades available! Tested and
endorsed by experts, PGT blades outperform and outlast all other
blades. Double tooth are easy to distinguish from skip tooth having
two teeth together followed by a flat space for more efficient chip
removal. Their razor sharp teeth cut faster, smoother, and more accurately
in both straight and radius cuts. A unique tooth geometry and widely
spaced gullets minimize burning. Made of the finest carbon steel for
maximum strength, durability and longest blade life.
Item# Univ# Width Thick TPI/Style Blister(6) Gross
45502 5RG .040” .018" 12/9 Skip/Rev $5.50 $74.95
45702 7RG .046” .018" 10/7 Skip/Rev $5.50 $74.95
45902 9RG .048” .018" 8/6 Skip/Rev $5.50 $74.95
49502 5RG .045” .018" 12/8 Dbl/Rev $5.50 $74.95
49702 7RG .047” .018"10.5/8 Dbl/Rev $5.50 $74.95
49902 9RG .049” .018" 9/6 Dbl/Rev $5.50 $74.95
49802 PGT Assortment 18 Pack* ............................................$14.95
*Contains 6 each of 49502, 49702, 49902.
Olson Scroll Saw Blades
www.tufftooth.com18
Buy 6 or moreblister packs fora 15% discount!
Crown Tooth
Unique tooth design allows the blade to cut on both the up and down
stroke. Cuts a little slower for more control, useful in delicate fretwork. Finish
is smooth with clean, sharp, splinter-free edges in hard/soft wood, plywood,
plastic and Corian®. Two-way cutting action prevents melting behind
the cut in most plastic including acrylic, lexan (polycarbonate), fiberglass,
and plexiglas. Has no top or bottom for easy blade installation. Blade
can be turned over for a fresh new set of teeth.
Item# Univ# Width Thick TPI Blister(12) Gross
CT620 2/0 .024" .011" 20 $6.95 $62.95
CT622 2 .026" .013" 20 $6.95 $62.95
CT623 3 .032" .014" 16 $6.95 $62.95
CT625 5 .038" .016" 16 $6.95 $62.95
CT627 7 .045" .017" 11 $6.95 $62.95
CT629 9 .053" .018" 6 $6.95 $62.95
CT632 12 .065" .024" 6 $6.95 $62.95
Double Tooth
Preferred by many scroll saw users. Double Tooth blades are
distinguished from regular skip tooth fret saw blades as having two teeth
together followed by a flat space for efficient chip removal. Double
tooth blades cut fast, leaving clean edges in wood and plastic. The
432D is considered the best blade for cutting wood veneer!
Item# Univ# Width Thick TPI Blister(12) Gross
432D 3/0 .023” .008” 33 $5.50 $49.95
433D 2/0 .024” .011” 37 $5.50 $49.95
434D 1 .026" .013" 30 $5.50 $49.95
435D 3 .032" .014" 23 $5.50 $49.95
436D 5 .038" .016" 16 $5.50 $49.95
437D 7 .044" .018" 13 $5.50 $49.95
438D 9 .053" .018" 11 $5.50 $49.95
439D 12 .061" .022" 10 $5.50 $49.95
493D Double Tooth Assortment 36 Pack* ................................$14.95
*Contains 12 each of 435D, 436D, 438D.
Olson Scroll Saw Blades
Order Desk: 1-800-461-3895 19
Buy 6 or moreblister packs fora 15% discount!
Reverse Tooth
Reverse Tooth blades with same performance as our skip tooth blades
with the added benefit of reverse teeth for a smooth, splinter free finish
on top and bottom surfaces. Excellent blade for eliminating tear-out on
birch and maple plywood.
Item# Univ# Width Thick TPI/Style Blister(12) Gross
420R - .100" .022" 9/5 Skip $6.25 $54.95
440R 2/0R .026" .011" 28/21 Skip $6.25 $54.95
443R 2R .029" .012" 20/14 Skip $6.25 $54.95
446R 5R .038" .016" 12.5/9 Skip $6.25 $54.95
448R 7R .045" .017" 11.5/8 Skip $6.25 $54.95
450R 9R .054" .019" 11.5/8 Skip $6.25 $54.95
453R 12R .062" .024" 9.5/6 Skip $6.25 $54.95
492R Reverse Tooth Assortment 36 Pack ..............................$16.95
*Contains 12 each of 443R, 446R, 448R.
Skip Tooth
Skip tooth blades are available in a wide range. For hand or machine
sawing of wood, plastic, and fibrous materials. Skip tooth blades cut
fast, provide good chip clearance and smooth finishes.
For Cutting Metal: Skip Tooth Scroll Saw Blades may out-perform metal
cutting or jewelers piercing scroll saw blades in cutting metal. Any Skip
Tooth blade up through a Univ# 5 will cut metal but Univ# 3/0 to Univ# 2
is preferred for inside cuts and marquetry panels. Skip Tooth blades can
cut cold rolled steel, copper, brass, aluminum sheet and bronze. Soft
metal up to 1/8” thick can be cut easily, whether a single sheet of stock
or several thinner sheets in a stack.
Item# Univ# Width Thick TPI Blister(12) Gross
400F 3/0 .022" .008" 33 $5.50 $49.95
440F 2/0 .022" .010" 28 $5.50 $49.95
443F 2 .029" .012" 20 $5.50 $49.95
445F 4 .035" .015" 15 $5.50 $49.95
446F 5 .038" .016" 12.5 $5.50 $49.95
448F 7 .045" .017" 11.5 $5.50 $49.95
450F 9 .053" .018" 11.5 $5.50 $49.95
453F 12 .062" .024" 9.5 $5.50 $49.95
494F Skip Tooth Assortment 36 Pack ....................................$14.95
*Contains 12 each of 443F, 446F, 448F.
Olson Scroll Saw Blades
www.tufftooth.com20
Buy 6 or moreblister packs fora 15% discount!
Spiral
Spiral Tooth blades saw in all directions with 360º cutting capability. Excellent
for 0º radius scroll/fret work you never have to turn the workpiece. For
cutting wood, plastic, wax, non-ferrous metals, plaster, bone, horn,
etc. (Note: You can use spiral blades on non-ferrous metals but Skip
Tooth, PGT and Mach blades are the blades recommended for non-ferrous
metal.) For use in power scroll saws and hand-held fret and jewelers
saw frames. Cutting speed and finish depend on material thickness
and number of teeth per inch. Spiral Tooth Blades with Flat Ends for
easier blade installation and retention. These premium blades are made
of high carbon steel, hardened and tempered to stay sharp longer. Good
for bevel cutting letters in names. Increase throat capacity and cut longer
pieces without turning!
Item# Univ# Kerf TPI End Style Blister(12) Gross
461S 0 .032" 46 Regular $6.25 $54.95
463S 2 .035" 41 Regular $6.25 $54.95
465S 4 .041" 36 Regular $6.25 $54.95
468S 2 .035" 41 Flat $7.50 $66.95
469S 4 .041" 36 Flat $7.50 $66.95
Metal Cutting Blades
These metal cutting scroll saw blades are made specifically for power
scroll saws. They are made from hardened and tempered steel and
have more teeth per inch than regular scroll saw blades for cutting
thin metal and other hard materials.
Item# Univ# Wide Thick TPI/Style Blister(12) Gross
485M 7 .041" .019" 30/Reg $6.95 $51.95
487M 9 .049" .022" 25/Reg $6.95 $51.95
490M 12 .070" .023" 20/Reg $6.95 $51.95
Thick Wood Hook Tooth
Extra wide gullets for rapid cutting of solid hard/soft wood and multi-layers
from 3/4” up to 2” thick without burning! Hardened and tempered teeth
for extra blade life. Straight cuts or tight turns. Leaves a medium smooth
finish. Continuous teeth (end to end) provide additional blade strength
during tensioning process (eliminates distortion) to assure accurate cuts
and minimum blade breakage. Every tooth set.
Item# Wide Thick TPI Style Blister(12) Gross
40800 .080” .018” 7 Hook $6.25 $54.95
Olson Scroll Saw Blades
Order Desk: 1-800-461-3895 21
Buy 6 or moreblister packs fora 15% discount!
5” Pin End
5″ is measured between the pins. Perfect for Sears Craftsman, Penn
State, Delta, Ryobi, and all 15″ and 16″ imported scroll saws. 5″ pin
end blades offer a choice of tooth styles that includes regular, hook,
skip and skip reverse. Teeth Per Inch vary from the most coarse –
7TPI, to the finest - 25TPI.
Item# Width Thick TPI Style Blister(6) Gross
405P .100” .018” 20 Reg $4.25 $72.95
410P .100” .018” 7 Hook $4.25 $72.95
411P .100” .018” 15 Reg $4.25 $72.95
412P .100” .018” 10 Reg $4.25 $72.95
420P .100” .018” 9/5 Rev/Skip $4.25 $72.95
424P .070" .010" 18.5 Skip $4.25 $72.95
Item# Width Thick TPI Style Blister(12) Gross
425P .070” .014” 18.5 Skip $5.50 $54.95
427P .070" .010" 25 Skip $5.50 $54.95
495P Pin End Assortment 18 Pack* ........................................$10.95
*Contains 6 each of 411P, 412P, 424P
3” Pin End
2-3/4″ is measured between the pins and are available with regular or
skip teeth. They are used on Hobby Scroll Saws such as Sears Craftsman®,
older Dremel® MotoSaws, Delta 15″ and Emco Lux to cut wood, plastic
and thin mild metals and provide a medium smooth finish.
Item# Wide Thick TPI Style Blister(6) Gross
429 .068" .014” 18.5 Reg $3.10 $56.95
430 .150" .015" 15 Skip $3.10 $56.95
6” Regular Tooth
6” blades are for use in scroll saws with a longer stroke – over 1-1/4”
and for cutting stock more than 2” thick. Regular Tooth for precise
internal and external cutting of irregular shapes and straight cut off
applications in all types of sheet materials with a medium smooth finish.
Item# Wide Thick TPI Blister(12)
411-6DZ .100" .022" 15 $6.95
412-6DZ .100" .022" 10 $6.95
Olson Scroll Saw Blades
www.tufftooth.com22
Buy 6 or moreblister packs fora 15% discount!
Scroll Saw Files
Convert your scroll saw into a power sander! Great for smoothing,
sanding, shaping and correcting lines in non-metallic materials. Shapes
and sands wood, plaster, greenware, soapstone and non-ferrous metals
including copper and brass. Works in most scroll saws taking 5” pin or
plain end blades. Can also be used in pin vises, craft knife handles, mini
hack, jeweler and hand fret saws.
Item# Width Thick Type Blister(2)
42101 .156" .056" Pin End $9.75
42100 .156" .056" Plain End $9.75
Plain End Scroll Saw Blade Assortment
36 Blades in this Assortment of Plain End Blades – 12 of each:
446R (Univ. No. 5R - .038” wide x .016” thick, 12.5/9 rev TPI)
Reverse Tooth Blades for a smooth, splinter free finish on top and bottom
surfaces. Eliminates tear-out on birch and maple plywood. For fret sawing
hard wood to 1/2” and soft wood to 3/4”.
448F (Univ. No.7 - .045” wide x .017” thick, 11.5 TPI)
Skip Tooth Blades cut fast, provide good chip clearance and smooth
finish. Popular for cutting hard and soft woods 3/16” up to 2”. Also cuts
plastic, paper, felt, bone, etc.
463S (Univ. No. 2 - .035” kerf, 41TPI)
Plain End Spiral Tooth Blades saw in all directions with 360º cutting
capability. Excellent for 0º radius scroll/fret work, you never have to turn
the workpiece. Medium speed and medium rough finish cutting of hard
and soft wood, plaster and wallboard.
49604 Plain End Assortment 36 Pack*..............................................$13.95
*Contains 12 each of 446R, 448F, 463S.
10” Bread Knives
This bread knife is 10" long and has a 1/8" hole in each end. Great for
making your own bread knives.
Bread Knives ..............................................................................$2.95
Olson Scroll Saw Blades
Order Desk: 1-800-461-3895 23
Buy 6 or moreblister packs fora 15% discount!
Sanding Mop Kit
The Sanding Mop is great for routered edges and general purpose profile
sanding. Includes 48 strips of sandpaper, one mandrel, five spacers
and two stabilizers. Available in 80, 120, 180 ,220, & 320 grit. When
ordering two grits, keep in mind that the most popular combination is
120 and 220 grit. They are a superior mixture for use on both hardwoods
and softwoods.
80 grit: Very aggressive. Best used for rough hardwood, furniture stripping,
log home refinishing, and patio furniture.
120 grit: For hardwood. Most popular grit for hardwood mouldings,
panel doors, turnings, legs. Exceptional performance when used with
stabilizers on routered edges.
180 grit: Mainly used on MDF, poplar and other medium hardwoods.
Excellent grit in production shops for pine.
220 grit: The most popular finishing grit. For softwood. Excellent
performance on pine. Can be used with stabilizers for edges or with
spacers for initial in between coat sanding.
320 grit: The most substantial time saver when used with spacers for
finishing a project. It does all the in-between coat sanding on carvings and
even on assembled raised panel doors. Excellent set up grit for polishers.
4” Sanding Mop Kit (choose 1 grit) ..........................................$25.00
6” Sanding Mop Kit (choose 1 grit) ..........................................$40.00
4” Sanding Mop Variety Pack (choose 2 grits) ........................$45.00
6” Sanding Mop Variety Pack (choose 2 grits) ........................$72.00
Sanding Mop Refill Strips
Each refill includes 48pc of sandpaper. Choose from 80, 120, 180,
220 & 320 grit.
4” Sanding Mop Refill Strips (choose 1 grit) ............................$20.00
6” Sanding Mop Refill Strips (choose 1 grit) ............................$34.00
Sanding Mop Stabilizers (pair)
Large white nylon discs (that do not mark wood) used on the outside of
the sanding mop to create a stiffer, more aggressive sanding mop. Allows
only the tips of the strips to sand. Available in 4” and 6” diameter.
Sanding Mop Stabilizers (pair) ..................................................$5.00
Sanding Mop Spacers
Small washers to place between some of the sanding mop strips to
create a softer mop. 5 pieces per package.
Sanding Mop Spacers................................................................$2.00
Sanding Mop Mandrel
This is the mandrel included in the Sanding Mop kit. It's a 1/2" mandrel
which tapers down to 1/4" so it will fit into any drill or drill press.
Sanding Mop Mandrel ................................................................$7.00
The Sanding Mop
www.tufftooth.com24
Sanding Belts
These Klingspor belts are an industrial quality, semi-open coat, aluminum
oxide cloth backed belt. These belts can be used on any type of wood
and light metal applications. Did you know all of these belts can run in
EITHER direction? All the belts are joined with a “Butt Splice”, in which
the belt ends are butted together and joined by high strength tape on
the underside of the joint. This allows the belt to run in either direction
for greater belt life.
Grit 3” x 24” 4” x 36” 6” x 48”
60 $2.45 $4.85 $7.75
80 $2.45 $4.85 $7.75
100 $2.45 $4.85 $7.75
120 $2.45 $4.85 $7.75
150 $2.45 $4.85 $7.75
V-Drum Sander Rolls
This Stearate coated aluminum oxide paper backed roll is primarily
sold for the V-Drum Sander. Get the finish you desire without your
paper loading up.
Grit 3” x 5yd 3” x 10yd
60 $11.95 $23.95
80 $10.95 $19.95
100 $10.95 $19.95
120 $10.95 $19.95
150 $10.95 $19.95
180 $10.95 $19.95
220 $10.95 $19.95
240 $10.95 $19.95
320 $10.95 $19.95
Abrasive Cleaner
Extend the life of your abrasives by cleaning the particles off the
abrasive. Removes most sawdust, pitch and adhesives from discs, belts
and drums. For best results, clean abrasives frequently. Measures
8”x1-1/2”x1-1/2”.
Abrasive Cleaner ......................................................................$15.95
Sanding Supplies
Order Desk: 1-800-461-3895 25
R&D Bandsaws
42 Regan Road, Unit 18
Brampton, Ontario L7A 1B4
Canada
Order Desk: 1-800-461-3895
Information: (905) 840-0399
Fax: (905) 840-4398
www.tufftooth.com
Hours:
Monday to Friday 9:00am to 4:30pm
Shipping and Handling:
Orders are sent by Canada Post Expedited Parcel service. The standard delivery in Ontario is 1-3 business days
and 2-7 days for all other provinces. The packing and delivery charges to one address anywhere in Canada are:
ON & QC: ................................................................................$12.00
AB, BC, MB, NB, NL, NS, NU, PE & SK: ................................$15.00
NT & YT: ........................................................Actual shipping charges
Air Stage Addresses: ....................................Actual shipping charges
When ordering 1” blades and wider, bandsaw fences and coilstock, actual shipping charges will apply.
Payment Options:
Visa, MasterCard and Money Orders.
Taxes:
Orders shipped to AB, BC, MB, NT, NU, QC, SK & YT are subject to 5% GST. Orders shipped to NB, NF, ON
are subject to 13% HST. Orders shipped to PEI are subject to 14% HST. Orders shipped to NS are subject
to 15% HST. All books are taxed at a rate of 5%.
International Orders:
U.S. orders are sent by Canada Post Expedited Parcel USA. The delivery standard is 4-8 business days. The
actual shipping charges will be applied. Please contact customer service for a shipping estimate.
Returns:
A 25% restocking fee applies to all custom items that are returned and to items that are returned that are not
in their original condition.
Please note: Our Canadian dollar prices are in effect July 1, 2018 and supersede those previouslypublished. While we make every attempt to verify published prices, an incorrect price may be inadvertentlyprinted. Refer to our website for current prices. All prices are subject to change without notice.
General Information
www.tufftooth.com26
27
Name: ..............................................................................................................................................................
Address: ..........................................................................................................................................................
City: ........................................................................Province:..........................................................................
Postal Code:............................................................Phone: ( ) ..............................................................
Visa MasterCard Money Order Expiry Date
Order Form
Qty Length Width TPI2Wh or
3WhDescription Unit Price Total
R&D Bandsaws
42 Regan Road, Unit 18
Brampton, Ontario L7A 1B4
Canada
Order Desk: 1-800-461-3895
Information: (905) 840-0399
Fax: (905) 840-4398
www.tufftooth.com
Hours:
Monday to Friday 9:00am to 4:30pm
Subtotal
Discount
Subtotal
Shipping
Subtotal
HST
GST
TOTAL
R&D Bandsaws42 Regan Rd, Unit 18
Brampton, Ontario L7A 1B4
Canada
Information: (905) 840-0399
Order Desk: 1-800-461-3895
Fax: (905) 840-4398
Email: [email protected]
Website: www.tufftooth.com
Store Hours:Monday to Friday 9:00am - 4:30pm