RCL100F-F36 100 Flex Deck Parts Manual - Lastecgateway.lastec.com/manuals/Parts/100EFKC (Kubota).pdf · General Information 1 How To Use The Parts List 1-2 Mower//021015 General Information

RCL100F-F36100" Flex Deck

Parts Manual

Printed in the United States of America, all rights reserved. No part of this manual may be reproduced in any form by any photographic, electronic, mechanical or other means or used in any information storage and retrieval system without written permission from

Table of Contents Section-Page

SECTION 1 GENERAL INFORMATION 1-1

1.1 How To Use The Parts List ....................................................................................... 1-21.2 Torque Values ........................................................................................................... 1-31.3 Decal Locations ......................................................................................................... 1-41.4 Belts and Deck Weldments ....................................................................................... 1-8

SECTION 2 MOUNTING HARDWARE 2-1

2.1 Hardware Kit ............................................................................................................. 2-22.2 Lift Assist Assemblies (Serial #46680113 and later) ................................................ 2-42.3 Lift Assist Assemblies (Prior to Serial #46680113).................................................. 2-62.4 Weight Kit and Main Harness Assembly .................................................................. 2-82.5 Hardware Kit (CE Only) ......................................................................................... 2-102.6 Lift Assist Assemblies (CE Only) ........................................................................... 2-122.7 Deck Lift Lock Assembly (CE Only)...................................................................... 2-14

SECTION 3 DRIVE SYSTEM 3-1

3.1 Gearbox Idler............................................................................................................. 3-23.2 Gearbox Assembly .................................................................................................... 3-43.3 Superior Gearbox....................................................................................................... 3-63.4 PTO 049615............................................................................................................... 3-8

3 100EFKC//021015 Table of Contents

Table of Contents Section-Page

SECTION 4 MOWER DECKS 4-1

4.1 Deck 1 Hardware....................................................................................................... 4-24.2 Double Pulley Spindle............................................................................................... 4-44.3 Spindle Housing, Decks 1, 2, 4 and 5........................................................................ 4-64.4 Deck 1 Idler Assembly .............................................................................................. 4-84.5 Deck 2 Hardware..................................................................................................... 4-104.6 Deck 2 Covers ......................................................................................................... 4-124.7 Double Pulley Spindle............................................................................................. 4-144.8 Deck 3 Hardware..................................................................................................... 4-164.9 Deck 3 Main Frame Cover ...................................................................................... 4-184.10 Triple Pulley Spindle............................................................................................... 4-204.11 Spindle Housings..................................................................................................... 4-224.12 Deck Drive Idler ...................................................................................................... 4-244.13 Grass Discharge, Deck 3 ......................................................................................... 4-264.14 Deck 4 Hardware..................................................................................................... 4-284.15 Deck 4 Covers ......................................................................................................... 4-304.16 Deck 5 Hardware..................................................................................................... 4-324.17 Deck 5 Idler ............................................................................................................. 4-344.18 Grass Discharge Deck 5 .......................................................................................... 4-364.19 Mulching Dam Kit (Optional) ................................................................................. 4-384.20 Wheel Yoke Assembly ............................................................................................ 4-404.21 9” x 3.5” Wheel Assembly, Solid............................................................................ 4-424.22 Deck 2 and 4 Wheel Yoke Assembly...................................................................... 4-444.23 Wheel Lift Rod Assembly ....................................................................................... 4-464.24 Deck Lift Cylinder Assembly.................................................................................. 4-484.25 Hydraulic Hoses ...................................................................................................... 4-504.26 Hardware Kit (CE Only) ......................................................................................... 4-52

SECTION 5 INDEX 5-1

Table of Contents 100EFKC//021015 4

Mower//021015 1-1

1

SECTION 1 GENERAL INFORMATION

General InformationHow To Use The Parts List1

1-2 Mower//021015 General Information

1.1 How To Use The Parts List

Use the table of contents or part number index to locate the part you need.

Go to the appropriate section and locate the part in the table and illustration.

Parts shown indented under another part are included with that part. IMPORTANT:Assemblies marked with a diamond () are non-saleable and all the parts shown as included need to be purchased separately.

See the sample table below. Sample Assembly A01111 includes part F02222-22 and sub-assembly A03333. The diamond () indicates that assembly A01111 is non-saleable and all the parts shown as included need to be purchased separately. Subassembly A03333 includes parts S04444-4 and F07777-77. The diamond () indicates that subassembly A03333 is non-saleable and all the parts shown as included need to be purchased sepa-rately.

To Order Parts:

From the continental U.S., call your local Lastec distributor to order parts. If there is no Lastec distributor in your area, call 1-800-515-6798. Have your customer num-ber, unit serial number, and part numbers ready when you call.

From other international locations, contact the Lastec distributor in your area for parts.

REF PART # DESCRIPTION (Indicates Non-Saleable Items) COMMENTS QTY.

A01111 Sample Assembly 1

1 F02222-22 Sample Part 1

A03333 Sample Subassembly 1

2 S04444-4 Sample Part 1

3 F07777-77 Sample Part 1

General InformationTorque Values

General Information Mower//021015 1-3

1

1.2 Torque Values

Below is a table of suggested torque values for this unit. Please use these torque values

on this unit unless otherwise specified.

Grade Units SAE 5 SAE 8

Tensile

Strength

105000

PSI150000

PSI

Grade Mark

Bolt

Dia.

Threads.

Per In.Units SAE 5 SAE 8

6

8

10

10

12

1/4

1/4

5/16

5/16

3/8

3/8

7/16

7/16

1/2

1/2

9/16

9/16

5/8

5/8

3/4

3/4

7/8

7/8

1

32

32

24

32

24

20

28

18

24

16

24

14

20

13

20

12

18

11

18

10

16

9

14

8

in-lbs (Nm)

in-lbs (Nm)

in-lbs (Nm)

in-lbs (Nm)

in-lbs (Nm)

in-lbs (Nm)

in-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

20 (2.3)

24 (2.7)

35 (4.0)

40 (4.5)

50 (5.7)

95 (10.7)

95 (10.7)

17 (22.6)

20 (27.1)

30 (40.7)

35 (47.5)

50 (67.8)

55 (74.6)

75 (101.7)

85 (115.3)

105 (142.4)

115 (155.9)

150 (203.4)

160 (217.0)

170 (230.5)

175 (237.3)

302 (409.5)

300 (406.8)

466 (631.8)

-

30 (3.4)

45 (5.1)

50 (5.7)

65 (7.3)

125 (14.1)

150 (17.0)

23 (31.2)

25 (33.8)

40 (54.2)

45 (61.0)

65 (88.1)

70 (94.9)

100 (135.6)

110 (149.2)

135 (183.1)

150 (203.4)

195 (264.4)

210 (284.8)

220 (298.3)

225 (305.1)

473 (640.9)

400 (542.4)

714 (967.4)

General InformationDecal Locations1

1.3 Decal Locations

Decal Locations (US Only)

REF PART # DESCRIPTION COMMENTS QTY.

77700-05517 Decal Kit, 100EFKC 1

1 77700-03131 Decal, Danger - Rotating Blades Bilingua 5

2 77700-02860 Decal, 100in - White 2

3 77700-03132 Decal, Danger, Thrown Objects Bilingual 2

4 77700-02947 Decal, 3682/96 Gearbox Fluid 1

N/A Decal, Kubota Serial Plate Not Shown 1

1-4 100EFKC//021015 General Information

General InformationDecal Locations 1

067035

2. DO NOT PUT HANDS OR FEET INTOMOWER WHEN ENGINE IS RUNNING

3. DO NOT OPERATE MOWER WITHOUT DISCHARGE DEFLECTOR

063

327

063327

100”

100”

067

034

067034

0670

34

067

034

067

034

06

703

4

0670

34

06

703

5

2. D

O N

OT

PU

T H

AN

DS

OR

FE

ET

INT

OM

OW

ER

WH

EN

EN

GIN

E IS

RU

NN

ING

3. D

O N

OT

OP

ER

AT

E M

OW

ER

WIT

HO

UT

D

ISC

HA

RG

E D

EF

LE

CT

OR

067

03

5

2. D

O N

OT

PU

T H

AN

DS

OR

FE

ET

INT

OM

OW

ER

WH

EN

EN

GIN

E IS

RU

NN

ING

3. D

O N

OT

OP

ER

AT

E M

OW

ER

WIT

HO

UT

D

ISC

HA

RG

E D

EF

LE

CT

OR

067035



100_144

General Information 100EFKC//021015 1-5

General InformationDecal Locations1

Decal Locations (CE Only)


072738 Decal Kit, 100EFKC CE 1

1 77700-03131 Decal, Danger - Rotating Blades Bilingua 5

2 77700-02860 Decal, 100in - White 2

3 77700-03132 Decal, Danger, Thrown Objects Bilingual 2

4 77700-02947 Decal, 3682/96 Gearbox Fluid 1

5 045519 Decal, Sound Power Level 1

6 072605 Decal, CE Herald 1

N/A Decal, Kubota Serial Plate Not Shown 1


General InformationDecal Locations 1

067035



063

327

063327

100”

100”

067

034

06 7034

0670

34

067

0 34

067

034

06

703

4

0670

34

06

703

5

2. D

O N

OT

PU

T H

AN

DS

OR

FE

ET

INT

OM

OW

ER

WH

EN

EN

GIN

E IS

RU

NN

ING

3. D

O N

OT

OP

ER

AT

E M

OW

ER

WIT

HO

UT

D

ISC

HA

RG

E D

EF

LE

CT

OR

067

03

5

2. D

O N

OT

PU

T H

AN

DS

OR

FE

ET

INT

OM

OW

ER

WH

EN

EN

GIN

E IS

RU

NN

ING

3. D

O N

OT

OP

ER

AT

E M

OW

ER

WIT

HO

UT

D

ISC

HA

RG

E D

EF

LE

CT

OR

067035



072605

100_144-2


General InformationBelts and Deck Weldments1

1.4 Belts and Deck Weldments


1 77700-02892 Belt, Insta-Power 85830 2

2 77700-02903 Belt, Goodyear 85500 2

3 77700-02910 Belt, B-128 Deck Drive 1

4 77700-02969 Deck Sub-Assembly, EFLW #1 1

5 77700-02966 Deck Weldment, EFLW #2 1

6 067734 1

1 Replaced 77700-02954 EFK #3 Deck Weldment (Serial #44470712 and later).

Deck Weldment, EFK #3 1


8 77700-02972 Deck Sub-Assembly, EFLW #5 1


General InformationBelts and Deck Weldments 1

100_115B


Mower//021015 2-1

2

SECTION 2 MOUNTING HARDWARE

Mounting HardwareHardware Kit2

2.1 Hardware Kit


77700-02980 Hardware Kit, 100EFK 1

064225 Lift Arm Assembly, 100EFK Right 1

1 77700-02948 Lift Arm Weldment, 100EFK Right 1

2 77700-03120 Bumper, Table 1

3 77700-02821 Washer, 3/8” SAE Flat 1

4 75599-31913 Nut, 3/8-16 Hex Nyloc 1

W25TS04092 Nut, 3/8-16 Hex Nyloc U.K. Only 1

5 77700-02979 Bushing, 20 ID x 28 OD x 25 Oil 2

6 70070-00181 Fitting, 1/4-28 Straight Grease 2

W25TS04075 Fitting, 1/4-28 Straight Grease U.K. Only 2

7 75599-01870 Bolt, 3/4-10 x 3 1/2” Hex Head Grade 5 1

8 77700-03623 Spacer, 3/4” x 1 1/2” x 1/4” 1

9 77700-02796 Nut, 3/4-16 Hex Nylon Lock 1

10 75599-31015 Nut, 1/2-13 Hex 1

W25TS04089 Nut, 1/2-13 Hex U.K. Only 1

11 77700-02788 Bolt, 1/2-13 x 2” Full Thread Grade 5 1

12 77700-03859 1 Boss, Spring Spacer 1

13 75599-33014 Washer, 7/16” Split Lock 1


064226 Lift Arm Assembly, 100EFK Left 1

15 77700-03624 Lift Arm Weldment, 100EFK Left 1

16 77700-03120 Bumper, Table 1

17 77700-02821 Washer, 3/8” SAE Flat 1

18 75599-31913 Nut, 3/8-16 Hex Nyloc 1






22 77700-03623 Spacer, 3/4” x 1 1/2” x 1/4” 1

23 77700-02796 Nut, 3/4-16 Hex Nylon Lock 1

24 75599-31015 Nut, 1/2-13 Hex 1



067762 2 Lift Assist Assembly, 100EFK Right See Section 2.3 for parts 1

067766 3 Lift Assist Assembly, 100EFK Left See Section 2.3 for parts 1

064173 Weight Kit, EFK See Section 2.4 for parts 1

064172 Harness Assembly, 100EFK Main See Section 2.4 for parts 1

77700-03135 Screw, M4-.7 x 65 SHC 1

2-2 100EFKC//021015 Mounting Hardware

Mounting HardwareHardware Kit 2

77700-03136 Nut, M4-.7 Prev Torq 1

77700-03139 PTO Shaft Assembly, Kubota 24 In Not Shown 1

26 77700-03133 Bar, 100EFKC Spring Installation 1

77700-03019 Supplemental Harness, 100EF 1

1 Added 77700-03859 Spacer Boss, 75599-33014 7/16” Split Lock Washer and 77700-01242 7/16-14 x 1 1/4” Hex Head Bolt (Serial #45230812 and later)

2 Replaced 064227 100EFK Right Lift Assist Assembly (Serial #46680113 and later).3 Replaced 064228 100EFK Left Lift Assist Assembly (Serial #46680113 and later).

100_148-1B

Mounting Hardware 100EFKC//021015 2-3

Mounting HardwareLift Assist Assemblies (Serial #46680113 and later)2

2.2 Lift Assist Assemblies (Serial #46680113 and later)


067762 Lift Assist Assembly, 100EFK Right 1

1 77700-04426 Mounting Weldment, 100EFK Frame Right 1

2 77700-02804 Washer, 10mm Split Lock 2

3 77700-02811 Screw, M10-1.25 x 45 Hx Cap SC 2

4 77700-03003 Bolt, M12 x 1.75 x 50mm Hex Head FT CL10.9 3

5 77700-04427 Plate, 100EFD Link 1

6 77700-03006 Nut, M12 x 1.75 Free 3

7 77700-04428 Spring, Counter Balance 1

8 77700-02889 Washer, 1/2” Standard Flat 2

9 77700-03005 Nut, M12 x 1.75 Hex Nylock 3

10 77700-02846 Bushing, .875 Bearing 2

11 77700-04429 Chain, 5/16” x 7 Links 1

12 77700-02977 Plate, EFK Spring Mount 1

13 77700-02810 Bolt, M10-1.25 x 30mm HHFT 8.8 2

14 02572-50100 Nut, M10-1.25 Hex Nyl Lock 2


16 77700-04430 Spacer, .53ID x 1-1/4 OD x 1-1/16 Long 1

17 77700-03004 Bolt, 1/2-13 x 2-3/4” Hex Head Grade 5 1

18 77700-03142 Nut, 1/2-13 Jam 1

19 77700-02794 Nut, 1/2-13 Half Nyloc 1

20 77700-04431 Washer, Motor Mount 2

21 77700-04432 Sleeve, 7/8” OD x 2.20 Long Bushing 1

22 75599-32017 Washer, 5/8” SAE Flat 1

W25TS04095 Washer, 5/8” SAE Flat U.K. Only 1

23 77700-02800 Nut, 5/8-11 Jam Nylon Lock 1

067766 Lift Assist Assembly, 100EFK Left 1

24 77700-04433 Mounting Weldment, 100EFK Frame 1

25 02572-50100 Nut, M10-1.25 Hex Nyl Lock 4

26 77700-02811 Screw, M10-1.25 x 45 Hx Cap SC 2


28 77700-04427 Plate, 100EFD Link 1

29 77700-03006 Nut, M12 x 1.75 Free 4



32 77700-03005 Nut, M12 x 1.75 Hex Nylock 4

33 77700-02846 Bushing, .875 Bearing 2

34 77700-04429 Chain, 5/16” x 7 Links 1


36 77700-02810 Bolt, M10-1.25 x 30mm HHFT 8.8 2



Mounting HardwareLift Assist Assemblies (Serial #46680113 and later) 2


39 75599-32017 Washer, 5/8” SAE Flat 1





067032 Hose Assembly, 100EFK Hydraulic 1

43 77700-02991 Hose Assembly, 1/4” Hyd x 42-1/2" 2

44 77700-02992 Abrasion Sleeve, 41-1/2” Hyd. Hose 2

45 77700-02994 Fitting, Hyd QD Male 2

46 77700-03129 Bracket, 100EFK Hose Mtg 1

47 75599-32015 Washer, 1/2” SAE Flat 2


100_148-7B


Mounting HardwareLift Assist Assemblies (Prior to Serial #46680113)2

2.3 Lift Assist Assemblies (Prior to Serial #46680113)


064227 Lift Assist Assembly, 100EFK Right 1

1 77700-03693 1 Mounting Weldment, 100EFK Frame Right 1


3 77700-02811 Screw, M10-1.25 x 45 Hx Cap SC 2


5 77700-02950 Plate, 100EFD Link 1

6 77700-03006 Nut, M12 x 1.75 Free 3

7 77700-02907 Spring, 1-1/2 OD x 8-1/2 x .195 1


9 77700-03005 Nut, M12 x 1.75 Hex Nylock 4

10 77700-02769 Spacer, 1/4” Thk Deck Height 2

11 77700-02978 Chain, 5/16” x 9 Links 1


13 77700-02810 Bolt, M10-1.25 x 30mm HHFT 8.8 2

14 02572-50100 Nut, M10-1.25 Hex Nyl Lock 2

15 77700-038581 Bolt, M12 x 1.75 x 75mm Hex Head 1

16 77700-04430 2 Spacer, .53ID x 1-1/4 OD x 1-1/16 Long 1


18 77700-03142 Nut, 1/2-13 Jam 1

19 77700-02794 Nut, 1/2-13 Half Nyloc 1

064228 Lift Assist Assembly, 100EFK Left 1

20 77700-02952 Mounting Weldment, 100EFK Frame 1

21 02572-50100 Nut, M10-1.25 Hex Nyl Lock 4

22 77700-02811 Screw, M10-1.25 x 45 Hx Cap SC 2


24 77700-02950 Plate, 100EFD Link 1

25 77700-03006 Nut, M12 x 1.75 Free 4

26 77700-02907 Spring, 1-1/2 OD x 8-1/2 x .195 1


28 77700-03005 Nut, M12 x 1.75 Hex Nylock 5

29 77700-02769 Spacer, 1/4” Thk Deck Height 2

30 77700-02978 Chain, 5/16” x 9 Links 1


32 77700-02810 Bolt, M10-1.25 x 30mm HHFT 8.8 2







Mounting HardwareLift Assist Assemblies (Prior to Serial #46680113) 2

37 75599-32015 Washer, 1/2” SAE Flat 2


1 Replaced 77700-02951 100EFK Frame Mounting Weldment and (1) F05008-183 replaced (1) 77700-03003 M12 x 1.75 x 50mm Hex Head Full Thread Bolt to provide additional clearance (Serial #44660712 and later).

2 Spacer added and spacer fasteners replaced (Serial #45230812 and later).

100_148-2D


Mounting HardwareWeight Kit and Main Harness Assembly2

2.4 Weight Kit and Main Harness Assembly


064173 1

1 Weight Bracket Weldment modified to use two additional M10 x 1.25 x 35 Bolts, 10mm Split Lock Washers and M10 Flat Washer (3/12).

Weight Kit, EFK 1

1 75599-01880 Bolt, 3/4-10 x 4” Hex Head Grade 5 2

2 77700-03128 Plate, EFK Weight Bracket Angle 1

3 77700-03622 Bracket Weldment, EFK Weight 1

4 75599-31918 Nut, 3/4-10 Nylock 2

5 77700-00954 Bolt, M12 x 1.25 x 35mm Hex Head 2


7 77700-02039 Washer, M12 Flat 2

8 01053-51035 Bolt, M10 x 1.25 x 35 6

W25TS04099 Bolt, M10 x 1.25 x 35 U.K. Only 6


10 04015-60100 Washer, M10 Flat 6

W25TS04098 Washer, M10 Flat U.K. Only 6

064172 Harness Assembly, 100EFK Main 1

11 77700-02809 Tie Wrap, 3/16” x 6 UV Blk 5

12 77700-00991 Nut, 10-24 Hex Nylock 1

13 77700-02975 Bracket, Switch EFK 1

14 77700-03014 Bolt, #10-24 x 1/2” Ph Pan Hd, Type 23 1

15 77700-02935 Relay, ISO 12V Coil w/Diode 1

16 77700-03152 Switch Plate, Hydraulic Cylinder Shim 2

77700-02976 Wiring Harness, 100EFK Main Not Shown 1


Mounting HardwareWeight Kit and Main Harness Assembly 2

100_148-3C


Mounting HardwareHardware Kit (CE Only)2

2.5 Hardware Kit (CE Only)


072724 Hardware Kit, 100EFKC CE 1

072730 Lift Arm Assembly, 100EFKC CE Right 1

1 77700-02948 Lift Arm Weldment, 100EFK Right 1

2 77700-03120 Bumper, Table 1

3 77700-02821 Washer, 3/8” SAE Flat 1

4 75599-31913 Nut, 3/8-16 Hex Nyloc 1






8 77700-03623 Spacer, 3/4” x 1 1/2” x 1/4” 1

9 F05010-103 Nut, 3/4-10 Nylock 1

10 75599-31015 Nut, 1/2-13 Hex 1



12 F05010-164 Nut, 7/16-14 Jam 1

13 F05011-35 Washer, 7/16” Standard Flat 1

14 F05009-60 Bolt, 7/16-14 x 1 3/4” Hex Head G8 1

15 F05010-135 Nut, 7/16-14 Nylock 1

072737 Lift Arm Assembly, 100EFKC CE Left 1

16 77700-03624 Lift Arm Weldment, 100EFK Left 1

17 77700-03120 Bumper, Table 1

18 77700-02821 Washer, 3/8” SAE Flat 1

19 75599-31913 Nut, 3/8-16 Hex Nyloc 1






23 77700-03623 Spacer, 3/4” x 1 1/2” x 1/4” 1

24 75599-31918 Nut, 3/4-10 Nylock 1

25 75599-31015 Nut, 1/2-13 Hex 1



27 F05010-164 Nut, 7/16-14 Jam 1

28 F05011-35 Washer, 7/16” Standard Flat 1

29 F05009-60 Bolt, 7/16-14 x 1 3/4” Hex Head G8 1

30 F05010-135 Nut, 7/16-14 Nylock 1

072725 Lift Assist Assembly, 100EFK Right See Section 2.6 for parts 1

2-10 Lastec//021015 Mounting Hardware

Mounting HardwareHardware Kit (CE Only) 2

072728 Lift Assist Assembly, 100EFK Left See Section 2.6 for parts 1

064173 Weight Kit, EFK See Section 2.4 for parts 1

064172 Harness Assembly, 100EFK Main See Section 2.4 for parts 1

77700-03135 Screw, M4-.7 x 65 SHC 1

77700-03136 Nut, M4-.7 Prev Torq 1

067032 Hose Assembly, 100EFK Hydraulic See Section 2.6 for parts 1

31 77700-03133 Bar, 100EFKC Spring Installation 1

77700-03139 PTO Shaft Assembly, Kubota 24 In Not Shown 1

067770 Lock Assembly, Kubota Deck Lift See Section 2.7 for parts 1

77700-03713 PTO Shield Retaining Chain, Bondiol Not Shown 2

77700-03019 Supplemental Harness, 100EF 1

100_197-1

Mounting Hardware Lastec//021015 2-11

Mounting HardwareLift Assist Assemblies (CE Only)2

2.6 Lift Assist Assemblies (CE Only)


072725 Lift Assist Assembly, 100EFKC CE Right 1

1 072726 Mounting Weldment, 100EFK Frame Right 1


3 77700-02811 Screw, M10-1.25 x 45 Hx Cap SC 2


5 77700-04427 Plate, 100EFD Link 1

6 77700-03006 Nut, M12 x 1.75 Free 3



9 77700-03005 Nut, M12 x 1.75 Hex Nylock 3

10 77700-02846 Bushing, .875 Bearing 2

11 77700-04429 Chain, 5/16” x 7 Links 1


13 77700-02810 Bolt, M10-1.25 x 30mm HHFT 8.8 2

14 02572-50100 Nut, M10-1.25 Hex Nyl Lock 2




18 77700-03142 Nut, 1/2-13 Jam 1

19 77700-02794 Nut, 1/2-13 Half Nyloc 1



22 75599-32017 Washer, 5/8” SAE Flat 1



072728 Lift Assist Assembly, 100EFKC CE Left 1

24 072729 Mounting Weldment, 100EFKC CE Frame Right 1

25 02572-50100 Nut, M10-1.25 Hex Nyl Lock 4

26 77700-02811 Screw, M10-1.25 x 45 Hx Cap SC 2


28 77700-04427 Plate, 100EFD Link 1

29 77700-03006 Nut, M12 x 1.75 Free 4



32 77700-03005 Nut, M12 x 1.75 Hex Nylock 4

33 77700-02846 Bushing, .875 Bearing 2

34 77700-04429 Chain, 5/16” x 7 Links 1


36 77700-02810 Bolt, M10-1.25 x 30mm HHFT 8.8 2



Mounting HardwareLift Assist Assemblies (CE Only) 2


39 75599-32017 Washer, 5/8” SAE Flat 1










47 75599-32015 Washer, 1/2” SAE Flat 2


100_197-2


Mounting HardwareDeck Lift Lock Assembly (CE Only)2

2.7 Deck Lift Lock Assembly (CE Only)


067770 Lock Assembly, Kubota Deck Lift 1

1 071530 Latch Plate, Kubota 1

2 067771 Pedal Weldment, Kubota Lift Lock 1

3 072575 Pedal Pad, Deck Lift Lock 1

4 77700-02785 Bolt, 3/8-16 x 1 1/2” Full Thread Hex Head 2

5 77700-02793 Nut, 3/8-16 Half Nyloc 4

6 014817 Spring, Ext 1/2x2 1/4x.06 1

7 77700-03751 Pad, Seat/Hood Rubber Bumper 1

8 067789 Plate, Bumper Mount 1

9 F05010-156 Nut, 1/4-20 Half Nylock 1

10 75599-31913 Nut, 3/8-16 Hex Nyloc 2

11 F05011-3 Washer, 3/8” Flat SAE 2


13 071532 Bushing, Kubota Latch 2

14 77700-03713 PTO Shield Retaining Chain, Bondiol 2

15 77700-03135 Screw, M4-.7 x 65 SHC 1

16 77700-03136 Nut, M4-.7 Prev Torq 1


Mounting HardwareDeck Lift Lock Assembly (CE Only) 2

100_197-3


Mower//021015 3-1

3

SECTION 3 DRIVE SYSTEM

Drive SystemGearbox Idler3

3.1 Gearbox Idler


063934 Idler Assembly, EFLW Main Drive 1

1 77700-02798 Nut, 3/4-10 Stover Swaged 1

2 77700-02833 Washer, 3/4” AN Yel/Cad 2

3 77700-02772 Bushing, 3/4” ID x 1” OD x 1” Oil 2



6 77700-02959 Idler Weldment, EFLW Main Drive 1

7 77700-02901 Pulley, 4 “ OD Idler 1

8 75599-32015 Washer, 1/2” SAE Flat 1


9 77700-02794 Nut, 1/2-13 Half Nyloc 1

10 77700-02793 Nut, 3/8-16 Half Nylon Lock 2

11 77700-02863 Spring, 1” x 7” Extension 1

3-2 100EFKC//021015 Drive System

Drive SystemGearbox Idler 3

100-116

Drive System 100EFKC//021015 3-3

Drive SystemGearbox Assembly3

3.2 Gearbox Assembly


064155 Gearbox Assembly, 100EFK 1

1 77700-02988 Gearbox, Superior R100-9AAE-M0023 1

2 77700-02902 Guard, 325EF PTO Shaft 1

3 77700-02903 Belt, Goodyear 85500 2

4 75599-31913 Nut, 3/8-16 Hex Nyloc 5



W25TS04082 Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5 U.K. Only 4

6 77700-02783 Screw, 5/16-18 x 3/4” FHSw/Nyloc Patch B/O 4



9 77700-02913 Plate, EF Superior Gearbox Left 1

10 77700-02912 Plate, EF Superior Gearbox Right 1

11 70050-00936 Washer, 5/16” SAE Flat 4

064592 Clutch Assembly, Warner Electric 1

12 77700-02989 Clutch, Diesel Mower 1

13 70070-00179 Key, 1/4” Sq x 1-1/2” Long 1

14 75599-31912 Nut, 5/16-18 Nylok Hex 2

W25TS04091 Nut, 5/16-18 Nylok Hex U.K. Only 2

15 77700-02802 Washer, 5/16” Star IT 4

16 70050-00936 Washer, 5/16” SAE Flat 2


18 77700-02897 Stop Weldment, Warner C-Belt Clutch 1

19 77700-02826 Hose Clutch Stop Bushing 1

20 77700-02871 Clutch Wire, Warner Electric 10 inch 1

21 F05007-230 Bolt, 3/8-16 x 2 3/4” Full Thread Hex Head Grade 2 1

22 77700-03140 Washer, 7/16” Nord-Lock 1

23 77700-03141 Screw, 7/16-20 x 2-3/4” Hex Head Grade 8 1

24 F05010-1 Nut, 3/8-16 Hex 1


Drive SystemGearbox Assembly 3

100_117B


Drive SystemSuperior Gearbox3

3.3 Superior Gearbox

NOTE: Use 6 oz. of Mobilube Synthetic 75W90 to refill the gearbox.


77700-02988 Gearbox, Superior R100-9AAE-M0023 1

1 77700-02782 Bolt, 5/16-18 x 1.25” SHCS Torque to 17-21 ft.-lbs. 8

2 77700-02924 Housing, R100 Mach Thru 1/8 1/4 1

3 77700-02842 End Cap CP 1.500-.187 D#7647 1

4 77700-02923 Casting, R100 Tap 1

5 70050-94047 Plug, 1/4-18 NPT Schd w/3m 4

6 77700-02844 Plug, Vent 5 PSI 1

7 77700-02825 Bushing, Vent 1/4” NPT to 1/8” NPT 1

8 77700-02773 Plug, 1/8-27 NPT Schd w/3m Drain Plug 1

9 77700-02865 Seal, TC-1.00-1.50-.187 Polyacrylate 2

10 77700-02859 Bearing Cup, TMKN L44620 4

11 70050-02124 Bearing Cone, TMKN L44643 4

W25TS04073 Bearing Cone, TMKN L44643 U.K. Only 4

12 77700-02843 Ring, Superior GB Retaining R100 1

13 064547 Cross, Shaft/Gear 1

14 77700-02933 Cross Assembly, Shaft/Gear R100 1


Drive SystemSuperior Gearbox 3

100_118B


Drive SystemPTO 0496153

3.4 PTO 049615

Service and CE Parts

NOTE: Half Shafts are not sold separately.


1 77700-03139 PTO Shaft Assembly, Kubota 24 In 4-lobe Cross Section 1

2 77700-03699 Kit, Cross Bearing S1 22x54 Zerk In Cap 2

N/A Fitting, Straight Metric Grease Included in item 2

3 77700-03700 Yoke, Outer Self Lock Kubota 10 Spline 1

4 77700-03701 Yoke, Outer Pin Lock Mower 20 Spline 1

5 77700-03702 Ring, Bearing B&P Outer Shield Cone Fml 1

6 77700-03703 Ring, Bearing B&P Outer Shield Cone Male 1

7 77700-03704 Cone, B&P Outer Shield 2

8 77700-03705 Sleeve, Outer Shield 049615 Female 1

9 77700-03706 Decal, Bondioli Sleeve 1

10 77700-03707 Decal, Danger Bondioli Outer Drive Tube 1

11 77700-03708 Sleeve, Inner Shield 049615 Male 1

12 77700-03709 Screw, B&P Outer Shield Cone 6

13 77700-03135 Screw, M4-.7x65 SHC Zinc metric 1

14 77700-03136 Nut, M4-.7 Prev Torq Znc metric 2

PART # DESCRIPTION COMMENTS QTY.

77700-03711 Kit, Spring Lock Collar Rebuild 1

77700-03712 Kit, Safety Shield 049615 Complete Contains items 5, 6, 7, 8, 9, 11, 12 1

77700-03713 PTO Shield Retaining Chain, Bondiol CE Compliance 2

77700-03714 PTO CE Label Kit, Bondioli CE Compliance 1

3-8 Lastec//021015 Drive System

Drive SystemPTO 049615 3

100_061B

Drive System Lastec//021015 3-9

Mower//021015 4-1

4

SECTION 4 MOWER DECKS

Mower DecksDeck 1 Hardware4

4.1 Deck 1 Hardware


1 77700-02775 Cover, 1 3/8”” Hole Plug 1

2 77700-02791 Nut, 5/16-18 Nylon Locking Jam 3

3 77700-02776 Washer, Throttle Friction 2

4 77700-02938 Cover, #1 Deck 1

5 77700-02812 Nut, 10mm x 1.25 Nylon Metric 1

6 77700-02914 Dampener, Hand Control 1

7 77700-02817 Nut, M10-1.25 Free Zinc Plate Metric 1

8 77700-02810 Bolt, M10-1.25x30mm HHFT 8.8 Metric 1

9 75599-31913 Nut, 3/8-16 Hex Nylock 1





12 77700-02857 Nut, 5/8-11 FlexLoc 2

13 75599-31915 Nut, 1/2-13 Nyl Hex Lock 2

W25TS04093 Nut, 1/2-13 Nyl Hex Lock U.K. Only 2

14 77700-02985 Guard, Belt Cover 1

15 77700-03134 Rivet, 3/16” Dia x 3/8-1/2 Grip Range Pop 2



17 063940 Wheel Yoke Assembly, EFLW 9” See Section 4.20 for parts 1

18 049892 Spindle Assembly, 2861AGC Dbl Sheave See Section 5.5 for parts 1

77700-02969 Deck Sub-Assembly, EFLW #1 1


20 77700-03696 Shim, 1/5” Rocker 4

21 77700-03697 Rocker Weldment, #1 EFLW 1

22 75599-31913 Nut, 3/8-16 Hex Nyloc 3


23 77700-03749 Washer, 3/8x1-1/2 x 1/8” Thk Hardened 3


059126 1 Door Assembly, #1 Deck Trap 1

25 75599-01215 Bolt, 5/16-18 x 3/4” Hex Head Grade 5 3

W25TS04079 Bolt, 5/16-18 x 3/4” Hex Head Grade 5 U.K. Only 3


27 77700-02886 Clamp Plate, #1 Deck Trap Door 1

28 77700-02908 Door, #1 Deck Trap 1

29 063999 Idler Assembly, EFLW Low See Section 4.4 for parts 1

30 77700-02892 Belt, Insta-Power 85830 1


32 77700-02852 Wheel, Anti-Scalp, 5-5/8" Hole 1

4-2 100EFKC//021015 Mower Decks

Mower DecksDeck 1 Hardware 4

33 70070-00171 Nut, 5/8-11 Jam 1

34 77700-02800 Nut, 5/8-11 Jam Nyl Lock 1

1 059126 replaced 064555 #1 Deck Trap Door Assembly including (4) 75599-01215 5/16-18 x 1” Hex Head Bolt, (4) 77700-02821 3/8” Flat Washer, 77700-04447 #1 Deck Trap Door Clamp Plate and 77700-04446 #1 Deck Trap Door (10/13). Previously, 064555 re-placed 059126 #1 Deck Trap Door Assembly (9/11)

100_119D

Mower Decks 100EFKC//021015 4-3

Mower DecksDouble Pulley Spindle4

4.2 Double Pulley Spindle


049892 Spindle Assembly, 2861AGC Double Sheave Non-saleable item. Parts must be purchased separately.

1

1 70070-00181 1

1 70070-00181 replaced 77700-02813 3/16” x 3/16” Straight Grease Fitting to improve durability (Serial #41071011 and later).

Fitting, 1/4-28 Straight Grease 1


2 77700-02872 Bolt, Spindle Single Pulley Maximum Torque: 57 ft-lbs 1

3 77700-02840 Washer, 1/2” Plain Belleville 1

4 77700-02771 Key, 1/4” x 2 1/2” 1

5 77700-02909 Sheave, Double - 2561 Mower 1

6 77700-02845 Washer, 1/4” x 1.47” x 1.01” 1

7 77700-02787 Bolt, 3/8-16 x 1 1/2” Carriage Grade 5 4

8 77700-02876 Plate, Deck Reinforcing 2

9 043246 Spindle Assembly, Center w/Stiffener See Section 5.6 for parts 1

10 75599-31913 Nut, 3/8-16 Hex Nyloc 4


11 77700-02880 Blade, 21” x 2 1/2” x 1/4” High Lift 1

77700-03137 Blade, 21” Low-Lift Optional 1

77700-03138 Blade, 21” Gator Mulching Optional 1

77700-03127 Blade, 21” x 2 1/2” x 1/8” Low-Lift Ultra Optional 1

12 77700-02853 Washer, 2 1/2” x 11/16” x 3/16” Nylon 1

13 77700-02805 Washer, 2 1/2” OD x 5/8” ID x 3/16” Std Flat Znc Remove to install Anti-Scalp Blade Disc

1

14 75599-04735 Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5 Torque Value: 75 ft-lbs 1

15 77700-03122 Blade Disc, Anti-Scalp Optional part. Remove Item 13 to install Anti-Scalp Blade Disc

1


Mower DecksDouble Pulley Spindle 4

LT0033


Mower DecksSpindle Housing, Decks 1, 2, 4 and 54

4.3 Spindle Housing, Decks 1, 2, 4 and 5

Concerning Nachi Sealed Bearings:

One of the most common misconceptions that cause a high number of bearing failures is that a bearing needs to be completely packed full. Many people have been taught; the more grease, the better. We have even heard of cases where people do not feel bearing manufacturers use enough grease in sealed and shielded ball bearings, so they remove one seal or shield and pack the bearing with more grease. These misconceptions are completely false. Over lubri-cating the bearings forces the motor to work harder.

Nachi standard grease fill for sealed and shielded ball bearings is 20% to 30% full

Too much grease can cause excess friction, thereby overheating the bearing and causing remature failure.

Only a small of grease is required to lubricate a bearing in motion.

When a bearing is in motion, most of the grease is pushed to the side (channeling) leaving a thin film of oil between the raceways and rolling elements.

When using open bearings, pack the bearing as follows:


043246 Spindle Assembly, Center w/Stiffener Non-saleable item. Parts must be purchased separately.

1


2 75599-01225 Bolt, 5/16-18 x 1 1/4” Hex Head Full Thread Gr5 3

W25TS04080 Bolt, 5/16-18 x 1 1/4” Hex Head Full Thread Gr5 U.K. Only 3



5 77700-02873 Seal, 2561 Spindle 1

6 77700-02904 Collar, Spindle Top 1

7 77700-02779 O-Ring, Spindle 1

8 77700-02878 Bearing, 6206-2NSE 3

9 77700-02929 Housing, Spindle 1

10 77700-02807 Pin, 1/8” x 1/2” Roll 1

11 75599-31912 Nut, 5/16-18 Nylon Lock Hex 3


12 77700-02877 Spacer, Spindle Bearing 1

13 77700-02780 O-Ring, 2 7/16" ID x 3/16" Diameter 2

14 77700-02823 Washer, 1.50” x 1.185” x 16Ga 1

15 77700-02824 Washer, 2.435” x 1.185” x 11Ga 1

16 77700-02925 Shaft, Center Blade Spindle 1


Mower DecksSpindle Housing, Decks 1, 2, 4 and 5 4

LT0024B


Mower DecksDeck 1 Idler Assembly4

4.4 Deck 1 Idler Assembly


063999 Idler Assembly, EFLW Low 1

1 75599-01540 Bolt, 1/2-13 x 2” Hex Head 2

2 75599-32015 Washer, 1/2” SEA FLat 3


3 76700-40802 Pulley, 5” OD Idler 1

W25TS04101 Pulley, 5” OD Idler U.K Only 1

4 77700-02919 Weldment, 521E Idler Plate 1


6 7J245-58120 Fitting, Grease 90 Deg. 1/4-28 1

W25TS04099 Fitting, Grease 90 Deg. 1/4-28 U.K. Only 1


8 77700-02833 Washer, 3/4” AN Yel/Cad 2

9 77700-02792 Nut, 3/4-10 Half Nyloc 1

10 77700-02890 Pulley, 5” OD V-Groove Idler 1

11 77700-01456 Bolt, 5/16-18 x 1 1/2” Hex Head FT Grade 5 1

12 75599-31012 Nut, 5/16-18 Hex 1



14 75599-31912 Nut, 5/16-18 Nylok Hex 1


15 77700-04435 Washer, Water Shed Pulley 2


Mower DecksDeck 1 Idler Assembly 4

100_120B



4.5 Deck 2 Hardware




3 77700-02811 Screw, M10-1.25 x 45 Hx Cap SC Metric 1


W25TS04087 Bolt, 5/8-11 x 3” Hex Head Grade 5 U.K. Only 2

5 77700-02884 Bushing, Urethane Pivot 4


7 77700-02857 Nut, 5/8-11 FlexLoc 4

8 77700-02967 Hinge Weldment, EFLW #2 Deck 1




11 77700-02883 Tube, Belt Keeper 1

12 77700-02831 Bolt, 5/8-11 x 1 1/2” Hex Head Full Thread Grade 5 2

13 77700-02882 Spacer, Bearing 1

14 77700-02888 Bearing, 1.25” x 2.25” x .50” 1

15 75599-32017 Washer, 5/8” SAE Flat 1


16 77700-02800 Nut, 5/8-11 Jam Nyl Lock 1


18 75599-31915 Nut, 1/2-13 Nyl Hex Lock 2




20 77700-03130 Sleeve, .875” x 1.39” Lg Bushing 2

21 77700-02846 Bushing, .875” Bearing 2

22 77700-02777 Bolt, 5/16-18 x 2” Elevator 1


24 75599-31012 Nut, 5/16-18 Hex 1





27 058662 Spindle Assembly, 521E/Z #2 & 4 See Section 5.14 for parts 1

28 77700-03153 Nut, 100EF Hinge Cam Adjust 2



30 F05007-87 Bolt, 3/8-16 x 1” Hex Head Grade 5 1

31 77700-05516 Plate, Bearing Extension EFKC 1

32 F05010-224 Nut, 5/8-11 Flanged Hex Nylock 1



CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.33 F05010-222 Nut, 3/8-16 Flanged Hex Nylock 1

100_121D


Mower DecksDeck 2 Covers4

4.6 Deck 2 Covers


067792 1

1 067792 replaced 061641 Left Transition Cover Assembly (11/12). 061641 included 77700-03750 4520 #1 Deck Sliding Cover that replaced 77700-02982 #1 Deck Sliding Cover with Serial #45220612 and used (1) 77700-03751 Seat/Hood Rubber Bumper Pad and (1) F05010-69 1/4-20 Nylock Nut.

Cover Assembly, Left Transition 1

1 77700-02982 Cover, #1 Deck Sliding 1

2 77700-02778 Bumper, Rubber Button 4

3 77700-02981 Cover, #2 deck Right Sliding 1


5 70050-00936 Washer, 5/16” SAE Flat 4

6 77700-02808 Screw, #10 x 1/2” Long AB Thrd Slot Hex Head 8

7 77700-03015 Hinge, 521E Sliding Cover 1

8 77700-02870 Pivot Bearing, Cover 2



061639 Cover Assembly, #2 Deck 1

10 77700-02937 Cover Plate, Left 1




13 70050-00936 Washer, 5/16” SAE Flat 6

14 77700-02775 Cover, 1 3/8”” Hole Plug 1

15 77700-02939 Guard Weldment, #2 Front 1

16 77700-02916 Guard Weldment, #2 Rear 1


064558 2

2 064558 modified to improve fit (2/12). 064558 replaced 061603 #2 Trap Door Assembly including (3) 77700-01387 5/16-18 x 1” Hex Head Bolt, (3) 77700-02801 5/16” Split Lock Washer, 77700-02905 #2 Deck Trap Door Clamp Plate and 77700-02894 #2 Deck Trap Door (9/11).

Door Assembly, #2 Trap 1





21 77700-02894 Door, #2 Deck Trap 1

22 77700-02803 Washer, 5/16” x 1 1/4” Fender 2

23 77700-04437 Door, #2/4 Deck Trap 1

064661 Door Assembly, #2 Trap Added (9/11) 1





27 77700-04439 Door, #2 Deck Trap 1


Mower DecksDeck 2 Covers 4

100_034-2F


Mower DecksDouble Pulley Spindle4

4.7 Double Pulley Spindle


058662 Spindle Assembly, 521E/Z Non-saleable item. Parts must be purchased separately.

1

1 70070-00181 1




2 77700-02887 Bolt, Spindle Pulley 1/2-13 x 1 3/4” Maximum Torque: 57 ft-lbs 1

3 77700-02840 Washer, 1/2” Plain Belleville 1

4 77700-02770 Key, 1/4” x 2-1/2” 1

5 77700-02909 Sheave, Double - 2561 Mower 1

6 77700-02861 Washer, 3/8” x 1.5”x1.01” 1

7 77700-02845 Washer, 1/4” x 1.47” x 1.01” 1

8 77700-02787 Bolt, 3/8-16 x 1 1/2” Carriage Gr5 4


10 043246 Spindle Assembly, Center w/Stiffener See Section 5.6 for parts 1

11 75599-31913 Nut, 3/8-16 Hex Nyloc 4






13 77700-02853 Washer, 2-1/2” x 11/16” x 3/16” Nylon 1

14 77700-02805 Washer,2 1/2” ODx5/8” IDx3/16” Std Flat Znc Remove to install Anti-Scalp Blade Disc

1



1


Mower DecksDouble Pulley Spindle 4

100_018



4.8 Deck 3 Hardware




2 75599-32015 Washer, 1/2” SAE Flat 3



4 072105 Keeper Weldment, 100" Belt 1


W25TS04099 Fitting, Grease 90 Deg. 1/4-28 U.K Only 1

6 75599-31915 Nut, 1/2-13 Nylon Hex Lock 2


7 75599-31015 Nut, 1/2-13 Hex 2


8 70050-93549 Ring, 3/4” External - External 1

W25TS04074 Ring, 3/4” External - External U.K Only 1

9 77700-02833 Washer, 3/4” AN Yel/Cad 1


064568 1 Door Assembly #3 Deck Trap 1





14 77700-02891 Door, 521E/Z #3 Deck Trap 1

15 75599-01140 2 Bolt,1/4-20 x 2” Hex Head Grade 5 4

16 70050-00936 Washer, 5/16” SAE Flat 2

17 77700-04440 2 Cover, EFLW #3 Deck Right 1

18 77700-04441 2 Cover, EFLW #3 Deck Left 1



20 60009-60028 Bolt, 5/16-18 x 2 1/4” Hex Head 2

21 77700-02866 Clamp, 1” ID Coated 2

22 77700-02958 Cover, EFLW Front Frame 1

23 75599-31912 Nut, 5/16-18 Nylok Hex 2


24 77700-02793 Nut, 3/8-16 Half Nyloc 3

25 77700-02785 Bolt, 3/8-16 x 3/4” Carriage 2

26 77700-02955 Baffle Weldment, EFLW #1 & 3 Deck 1



28 064543 Spindle Assembly, 100EF #3 Deck See Section 4.10 for parts 1



CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.


30 063934 Idler Assembly, EFLW Main Drive See Section 3.1 for parts 1

31 063916 Idler Assembly, EFLW Deck Drive See Section 4.12 for parts 1

32 063944 Cover Assembly, EFLW Main Frame See Section 4.9 for parts 1


34 75599-32011 Washer, 1/4” SAE Flat 4

067087 Door Assembly, #3 Deck Trap Added (9/11) 1





38 77700-04443 Door, 521E/Z #3 Deck Trap 1

39 F05011-68 Washer, 1/2 Standard Flat 1

40 062051 Washer, Water Shed Pulley 1

41 F05011-9 Washer, 1/2 Split Lock 1

1 Replaced 058848 #3 Trap Door Assembly including (2) 77700-01387 5/16-18 x 1” Hex Head Bolt, (2) 77700-02801 5/16” Split Lock Washer, 77700-02906 #3 Deck Trap Door Clamp Plate and 77700-02891 521E/Z #3 Deck Trap Door (Serial #44470712 and later).

2 77700-04440 replaced 77700-02960 #3 Deck Right Cover, 77700-04441 replaced 77700-02960 #3 Deck Left Cover, (4) 75599-01140 replaced (5) 77700-03625 5/16-18 x 3/4” BHSC SS Screw (9/12). Replaced (5) 75599-01215 5/16-18 x 3/4” Hex Head Bolt, (5) 77700-02801 5/16” Split Lock Washer and (5) 70050-00936 5/16” SAE Flat Washer (Serial #43480512 to 44460712).

100_122E


Mower DecksDeck 3 Main Frame Cover4

4.9 Deck 3 Main Frame Cover


063944 Cover Assembly, EFLW Main Frame 1




3 70050-00936 Washer, 5/16” SAE Flat 7


5 77700-02965 Cover, EFLW Front RT Frame 1

6 77700-02964 Cover Weldment, EFLW Front LT Frame 1

7 77700-02839 Spacer, Plastic 3/4” OD x .325” ID x 1” 2

8 77700-02963 Cover, EFLW Main Frame Rear 2


Mower DecksDeck 3 Main Frame Cover 4

100_123


Mower DecksTriple Pulley Spindle4

4.10 Triple Pulley Spindle


064543 Spindle Assembly, 100EF #3 Deck Non-saleable item. Parts must be purchased separately.

1

1 70070-00181 1




2 77700-02887 Bolt, Spindle Pulley 1/2-13x1-3/4 Maximum Torque: 57 ft-lbs 1

3 77700-03007 Washer, 1/2” Nord-Lock 1

4 77700-02946 Washer, 1-3/4” x .51” x 1/4” 1

5 77700-02770 Key, 1/4” x 2-1/2” 1

6 77700-02986 Sheave, Triple - 100 Outfront Mower 1

7 77700-02845 Washer, 1/4” x 1.47” x 1.01 1

8 77700-02787 Bolt, 3/8-16” x 1 1/2” Carriage Gr5 4


10 058591 Spindle Assembly, 521E Center See Section 4.21 for parts 1

11 75599-31913 Nut, 3/8-16 Hex Nyloc 4






13 77700-02853 Washer, 2-1/2” x 11/16” x 3/16” Nylon 1

14 77700-02805 Washer, 2 1/2” OD x 5/8” ID x 3/16” Std Flat Znc Remove to install Anti-Scalp Blade Disc

1



1


Mower DecksTriple Pulley Spindle 4

100_124


Mower DecksSpindle Housings4

4.11 Spindle Housings

Concerning Sealed Bearings:

One of the most common misconceptions that cause a high number of bearing failures is that a bearing needs to be completely packed full. Many people have been taught; the more grease, the better. We have even heard of cases where people do not feel bear-ing manufacturers use enough grease in sealed and shielded ball bearings, so they remove one seal or shield and pack the bearing with more grease. These miscon-ceptions are completely false. Over lubricating the bearings forces the motor to work harder.

Nachi standard grease fill for sealed and shielded ball bearings is 20% to 30% full

Too much grease can cause excess friction, thereby overheating the bearing and causing remature failure.

Only a small of grease is required to lubricate a bearing in motion.

When a bearing is in motion, most of the grease is pushed to the side (channeling) leaving a thin film of oil between the raceways and rolling elements.


058591 Spindle Assembly, 521E Center Non-saleable item. Parts must be purchased separately.

1






5 77700-02873 Seal, 2561 Spindle 1

6 77700-02904 Collar, Spindle Top 1

7 77700-02779 O-Ring, Spindle 1

8 77700-02878 Bearing, 6206-2NSE 3

9 77700-02929 Housing, Spindle 1

10 77700-02807 Pin, 1/8” x 1/2” Roll 1

11 75599-31912 Nut, 5/16-18 Nylok Hex 3


12 77700-02877 Spacer, Spindle Bearing 1

13 77700-02780 O-Ring, 2-7/16" ID x 3/16" Diameter 2

14 77700-02823 Washer, 1.50” x 1.185” x 16Ga 1

15 77700-02824 Washer, 2.435” x 1.185” x 11Ga 1

16 77700-02928 Shaft, Extended Center Blade Spindle 1


Mower DecksSpindle Housings 4

100_005


Mower DecksDeck Drive Idler4

4.12 Deck Drive Idler


063916 Idler Assembly, EFLW Deck Drive 1



3 77700-02907 Spring, 1-1/2” OD x 8-1/2” x .195” 1

4 77700-03142 Nut, 1/2-13 Jam 1

5 77700-02794 Nut, 1/2-13 Hex Half Nylon Lock 2


7 77700-02921 Weldment, 521E Main Deck Idler 1

8 70060-02853 Fitting, 1/4-28 45 Deg Grease 1

9 76700-40802 Pulley, 5” OD Idler 1


10 75599-32015 Washer, 1/2” SAE Flat 1




Mower DecksDeck Drive Idler 4

100_125


Mower DecksGrass Discharge, Deck 34

4.13 Grass Discharge, Deck 3


063920 Chute Assembly, #3 Deck Rubber EFLW 1


2 70050-00936 Washer, 5/16” SAE Flat 6

3 77700-03694 1

1 Replaced 77700-02956 #3 Chute EFK Clamp Plate to improve grass discharge (Serial #44660712 and later).

Clamp Plate, #3 Chute EFK 1

4 77700-02957 Rubber Chute, #3 Deck EFK 1

5 70050-94190 Bolt, 5/16-18 x 1” Carriage Grade 5 5

6 77700-02858 Clamp Plate, Rubber Chute 1

7 77700-02803 Washer, 5/16” x 1 1/4” Fender 1



Mower DecksGrass Discharge, Deck 3 4

100_126B



4.14 Deck 4 Hardware




3 77700-02811 Screw, M10-1.25 x 45 Hx Cap SC Metric 1





7 77700-02857 Nut, 5/8-11 FlexLoc 4

8 77700-02971 Hinge Weldment, #4 EFLW Deck 1




11 77700-02883 Tube, Belt Keeper 1


13 77700-02882 Spacer, Bearing 1

14 77700-02888 Bearing, 1.25” x 2.25” x .50” 1

15 75599-32017 Washer, 5/8” SAE Flat 1


16 77700-02800 Nut, 5/8-11 Jam Nyl Lock 1


18 75599-31915 Nut, 1/2-13 Nyl Hex Lock 2



20 77700-03130 Sleeve, .875” x 1.39” Lg Bushing 2

21 77700-02846 Bushing, .875” Bearing 2

22 77700-02777 Bolt, 5/16-18 x 2” Elevator 1


24 75599-31012 Nut, 5/16-18 Hex 1





27 058662 Spindle Assembly, 521E/Z #2 & 4 See Section 5.14 for parts 1

28 77700-03153 Nut, 100EF Hinge Cam Adjust 2



30 F05007-87 Bolt, 3/8-16 x 1” Hex Head Grade 5 1

31 77700-05516 Plate, Bearing Extension EFKC 1





CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.

100_130C


Mower DecksDeck 4 Covers4

4.15 Deck 4 Covers


061646 Cover Assembly, #4 Pivoting 1





5 70050-00936 Washer, 5/16” SAE Flat 4

6 77700-02808 Screw, #10 x 1/2” Long AB Thrd Slot Hex Head 8

7 77700-03015 Hinge, 521E Sliding Cover 1

8 77700-02870 Pivot Bearing, Cover 2



061643 Cover Assembly, #4 Deck Pivoting 1

10 77700-02898 Cover Plate, Right 1




13 70050-00936 Washer, 5/16” SAE Flat 6

14 77700-02775 Cover, 1 3/8”” Hole Plug 1

15 77700-02915 Guard Weldment, #4 Rear 1

16 77700-02940 Guard Weldment, #4 Front 1


064574 1 Door Assembly, #4 Deck Trap 1



20 77700-05515 Clamp Plate, #4 Trap Door 1

21 77700-05514 Door, #4 Deck Trap 1

059082 Deflector Assembly, Grass 1

22 77700-02793 Nut, 3/8-16 Half Nylock 2

23 77700-02821 Washer, 3/8” Flat SAE 2

24 77700-03016 Deflector Plate, #5 Deck Grass 1

25 77700-02785 Bolt, 3/8-16 x 3/4” Carriage 2

064577 2 Door Assembly, #4 Deck Trap Added (9/11) 1

26 75599-01215 Bolt, 5/16-18 x 3/4” Hex Head 2



28 77700-02803 Washer, 5/16” x 1 1/4” Fender 2

29 77700-04437 Door, #2/4 Deck Trap 1

064580 Baffle Assembly, #4 Blowout Added (9/11) 1

30 77700-04444 Baffle Weldment, #4 Blowout 1

31 70060-04188 Bolt, 5/16-18 x 3/4” Carriage 2


Mower DecksDeck 4 Covers 4


1 Replaced 059180 #4 Trap Door Assembly including (3) 75599-01215 5/16-18 x 3/4” Hex Head Bolt, (3) 77700-02801 5/16” Split Lock Washer, 77700-02885 #4 Deck Trap Door Clamp Plate and 77700-02899 #4 Deck Trap Door (Serial #44470712 and later).

2 77700-04437 replaced 064578 #4 Deck Trap Door, removed 064579 Clamp Plate and added (2) 77700-02803 Washers (Serial #44470712 and later).

100_032-2E



4.16 Deck 5 Hardware


1 77700-02775 Cover, 1 3/8”” Hole Plug 1


3 70050-00936 Washer, 5/16” SAE Flat 1

4 77700-02776 Washer, Throttle Friction 2

5 75599-31912 Nut, 5/16-18 Nylock Hex 1


6 77700-02941 Cover Weldment, #5 1

7 77700-02810 Bolt, M10-1.25 x 30mm HHFT 8.8 metric 1

8 77700-02817 Nut, M10-1.25 Free Zinc Plate metric 1

9 77700-02914 Dampener, Hand Control 1

10 77700-02812 Nut, 10mm x 1.25 Nylon metric 1




13 75599-31915 Nut, 1/2-13 Nyl Hex Lock 2


14 77700-02857 Nut, 5/8-11 FlexLoc 2

15 77700-02985 Guard, Belt Cover 1

16 77700-03134 Rivet, 3/16” Dia x 3/8-1/2 Grip Range Pop 2



18 064135 Idler Assembly, EFLW High See Section 4.17 for parts 1


20 049892 Spindle Assembly, 2861AGC Dbl Sheave See Section 5.5 for parts 1

77700-02972 Deck Sub-Assembly, EFLW #5 1

21 067078 Deck Weldment, EFLW #5 1

22 77700-03696 Shim, 1/5” Rocker 1

23 77700-03698 Rocker Weldment, #5 EFLW 4

24 75599-31913 Nut, 3/8-16 Hex Nyloc 3


25 77700-03749 Washer, 3/8x1-1/2 x 1/8” Thk Hardened 3



28 77700-02852 Wheel, Anti-Scalp, 5-5/8" Hole 1

29 70070-00171 Nut, 5/8-11 Jam 1

30 77700-02800 Nut, 5/8-11 Jam Nyl Lock 1



100_131B


Mower DecksDeck 5 Idler4

4.17 Deck 5 Idler


064135 Idler Assembly, EFLW High 1

1 75599-01540 Bolt, 1/2-13 x 2” Hex Head 2

2 75599-32015 Washer, 1/2” SAE Flat 3



4 77700-02919 Plate Weldment, 521E Idler 1

5 77700-02794 Nut, 1/2-13 Half Nyloc 2


W25TS04099 Fitting, Grease 90 Deg. 1/4-28 U.K Only 1


8 77700-02792 Nut, 3/4-10 Half Nyloc 1

9 77700-02833 Washer, 3/4” AN Yel/Cad 2

10 76700-40802 Pulley, 5” OD Idler 1


11 77700-01456 Bolt, 5/16-18 x 1 1/2” Hex Head Grade5 FT 1

12 75599-31012 Nut, 5/16-18 Hex 1


14 75599-31912 Nut, 5/16-18 Nylok Hex 1


15 77700-04435 Washer, Water Shed Pulley 2


Mower DecksDeck 5 Idler 4

100_129B


Mower DecksGrass Discharge Deck 54

4.18 Grass Discharge Deck 5


061616 Chute Assembly, #5 Deck Grass 1



3 77700-02943 Support Plate, Chute Side 1

4 77700-02926 Chute, #5 Right Rubber Grass 1

5 77700-03126 Support Plate, Chute Top 1

6 77700-02911 Chute Tab, Inside Rubber 1

7 77700-02875 Support Plate, Chute Top 1

8 F05006-141 Bolt, 5/16-18 x 1” BHCS SS 2

9 77700-02803 Washer, 5/16” x 1 1/4” Fender 4

10 F05006-153 Bolt, 5/16-18 x 1-1/2 Carriage Grade 5 2


Mower DecksGrass Discharge Deck 5 4

LT0088C


Mower DecksMulching Dam Kit (Optional)4

4.19 Mulching Dam Kit (Optional)


77700-05518 Dam Kit, 100” Mulching 1

1 77700-03124 Mulching Plate, #3 1


3 70050-00936 Washer, 5/16” SAE Flat 6


5 77700-03143 Mulching Plate, #5 Deck 1


Mower DecksMulching Dam Kit (Optional) 4

100_036


Mower DecksWheel Yoke Assembly4

4.20 Wheel Yoke Assembly


063940 Wheel Yoke Assembly, EFLW 9 In 1

1 77700-02814 Washer, 1-1/16” x 1-3/4” x 1/8” Znc 2

2 77700-02945 Spring, Wheel Yoke 1-0 Urethane 1

3 77700-02820 Spacer, 1” ID x 1-3/4” OD x 1/4” 2

4 77700-02841 Spacer, 1 3/4” OD x 1 1/16” ID x 1” 3

5 77700-02838 Bushing, 1” ID x 1-1/4” OD x 1-1/4” Flanged 2

6 77700-02822 Pin, 3/8” Dia Lynch Locking 1

7 77700-02962 Yoke Weldment, EFLW 9 In 1


9 77700-02774 Spacer, 3/4” Axle Bolt 2

10 77700-02931 Wheel Assembly, 9x3.5 Reliance DM See Section 4.21 for parts 1

11 75599-32018 Washer, 3/4” SAE Flat 1




Mower DecksWheel Yoke Assembly 4

100_127


Mower Decks9” x 3.5” Wheel Assembly, Solid4

4.21 9” x 3.5” Wheel Assembly, Solid

NOTE: Wheels are shipped unlubricated from the factory. Insure proper lubrication, bear-ing preloading, and torque specifications are met. Use Loctite on all bolts. Tighten hub nuts to 145-170 in-lbs.

NOTE: All wheels should be lubricated, insuring grease passes through the seals, after every 8 hours of operation. (See Section 5 of the Owner’s Manual).

NOTE: When checking bearing preload, wheels should be placed on the spindles loose enough to spin freely only one complete revolution when spun by hand. Insure spacers are properly installed.


77700-02931 Wheel Assembly, 9” x 3.5” Reliance DM 1

1 75599-31012 Nut, 5/16-18 Hex Torque to 145-170 in-lbs 4



3 N/A Tire, Carlisle Reliance No-Flat Smooth Not Sold Separately 1

4 70030-02067 Seal, 1 1/8” ID Trb Bearing 2

5 77700-02864 Bearing, Tapered Roller 3/4” ID 2

6 77700-02855 Spacer, 3/4” Wheel Bearing 1

N/A Hub Assembly, 9/11” Demountable 1

7 N/A Hub, 9/11” Demountable 1

8 77700-02835 Bearing Race Insert, 3/4” TRB 2

9 70060-02853 Fitting, 1/4-28 45 Deg. Grease 1


Mower Decks9” x 3.5” Wheel Assembly, Solid 4

TR1017


Mower DecksDeck 2 and 4 Wheel Yoke Assembly4

4.22 Deck 2 and 4 Wheel Yoke Assembly

REF PART # DESCRIPTION COMMENTS QTY

064142 Wheel Assembly, Right Rear EFLW Deck 4 1


2 061634 Rod Assembly, Rear Deck Height See Section 5.34 for parts 1

3 77700-02770 Spacer, 5/16” Thick Deck Height 1

4 77700-02974 Wheel Weldment, Right Deck EFLW 1


W25TS04076 Bolt, 1/2-13 x 6 1/2” Hex Head Grade 5 U.K Only 1



8 77700-02857 Nut, 5/8-11 FlexLoc 2


10 F05011-73 Washer, 7/8” SAE Flat 2

11 77700-02774 Spacer, 3/4” Axle Bolt 1

12 77700-02931 Wheel Assembly, 9” x 3.5” Reliance DM See Section 4.21 for parts 1

13 77700-02774 Spacer, 3/4” Axle Bolt 1

064138 Wheel Assembly, Left Rear EFLW Deck 2 1


15 061634 Rod Assembly, Rear Deck Height See Section 5.34 for parts 1


17 77700-02973 Wheel Weldment, Left Rear EFLW 1


W25TS04076 Bolt, 1/2-13 x 6 1/2” Hex Head Grade 5 U.K Only 1



21 77700-02857 Nut, 5/8-11 FlexLoc 2


23 F05011-73 Washer, 7/8” SAE Flat 2

24 77700-02774 Spacer, 3/4” Axle Bolt 1

25 77700-02931 Wheel Assembly, 9” x 3.5” Reliance DM See Section 4.21 for parts 1

26 77700-02774 Spacer, 3/4” Axle Bolt 1


Mower DecksDeck 2 and 4 Wheel Yoke Assembly 4

100_128


Mower DecksWheel Lift Rod Assembly4

4.23 Wheel Lift Rod Assembly


061634 Rod Assembly, Rear Deck Height 1

1 77700-02767 Rod End, 1/2-20 Female 1

2 77700-02797 Nut, 1/2-20 Hex Jam 3

3 77700-02827 Spacer, 5/16” Thick Knurled 5


5 75599-32015 Washer, 1/2 SAE Flat 1


6 77700-02996 Rod, Deck Lift Lock 1

7 77700-02847 Spring, .72x1.5x.063 Compression 2

8 77700-02799 Nut, 1/2-20 Jam Nyl Lock 1


Mower DecksWheel Lift Rod Assembly 4

100_024


Mower DecksDeck Lift Cylinder Assembly4

4.24 Deck Lift Cylinder Assembly


059174 Cylinder Assembly, Deck Lift Deck 4 1

77700-02934 Cylinder Assembly, Deck Lift Deck 2 1

1 77700-03691 1

1 77700-03692 replaced (1) 77700-02862 Hydraulic Cylinder Large Chain Weldment and 77700-03691 replaced (1) 77700-02862 3/4-10 Flexloc Nut to improve durability (serial #42020212 and later).

Pin, 7/16” Dia Lynch Locking 1

2 77700-036921 Chain, 5/16” x 5 Links 1

3 75599-31913 Nut, 3/8-16 Hex Nylock 1


4 77700-02800 Nut, 5/8-11 Jam Nyl Lock 2

5 75599-32017 Washer, 5/8” SAE Flat 1


6 77700-02790 Nut, 1-14 Hex Jam 1

7 77700-02927 Block, Hydraulic Cylinder Pivot 1

8 77700-02895 Lock Plate, Hydraulic Cylinder 1







14 77700-02932 Cylinder, Hyd. Deck Lift 1

15 70080-01765 Pin, 1/2” Dia x 2 1/2” Detent 1

16 77700-02930 Lock Weldment, Deck Latch 1

17 77700-02781 Screw, 10-24 x 1/2” Sl Hex Machine 2

18 77700-02879 Switch Plate, Hydraulic Cylinder 1

19 77700-02868 Switch, DPST N/O N/C 1

20 77700-02795 Nut, #10-24 Keps 2

77700-03123 Fitting, 1/4” JIC x Male Pipe Run Tee- Tap Not Shown. Deck 4 2

77700-03121 Fitting, 1/4” NPT x 1/4” JIC w/5/16 Tap, Elbow Not Shown. Deck 2 2

77700-02881 Orifice, 5/16” OD x .040” ID x 3/8” Not Shown 2


Mower DecksDeck Lift Cylinder Assembly 4

100_029C


Mower DecksHydraulic Hoses4

4.25 Hydraulic Hoses



77700-02992 Abrasion Sleeve, 41-1/2” Hyd. Hose Not Shown 2

2 77700-02918 Hose Assembly, 48" 90 Deg JIC 1

75596-64130 Abrasion Sleeve, 50” Hyd. Hose Not Shown 1

W25TS04077 Abrasion Sleeve, 50” Hyd. Hose U.K. Only 1

3 77700-02917 Hose Assembly, 41.5 90 Deg JIC 1

77700-02993 Abrasion Sleeve, 43-1/2” Hyd. Hose Not Shown 1

4-50 Lastec//021015 Mower Decks

Mower DecksHydraulic Hoses 4

100_066

Mower Decks Lastec//021015 4-51

Hardware Kit (CE Only)4

4.26 Hardware Kit (CE Only)


067942 Kit, 100EFKC CE Hardware 1

1 77700-04449 Nut Assembly, 5/16-18 Cover Retaining 22

2 60009-60028 Bolt, 5/16-18 x 2 1/4” Hex Head 2

3 77700-04450 Spacer Assembly, Cover Retaining 2

4 77700-04451 Nut Keeper, Cover Retaining 2

5 77700-02044 Washer, #10 SAE Flat 3

6 77700-03134 Rivet, 3/16” Dia x 3/8-1/2” Grip Range Pop 13



8 77700-04452 Nut Assembly, 1/4-20 Cover Retaining 4


IS-0331 Instruction Sheet, 100EFKC CE Hardware Kit 1

4-52 Lastec//021015

Hardware Kit (CE Only) 4

100_179

Lastec//021015 4-53

Mower//021015 5-1

5

SECTION 5 INDEX

Part Number Index

01053-51035, Bolt, M10 x 1.25 x 35 2-8014817, Spring, Ext 1/2x2 1/4x.06 2-1402572-50100, Nut, M10-1.25 Hex Nyl Lock 2-4, 2-6,

2-1204015-60100, Washer, M10 Flat 2-8043246, Spindle Assembly, Center w/Stiffener 4-4, 4-6,

4-14045519, Decal, Sound Power Level 1-6049892, Spindle Assembly, 2861AGC Dbl Sheave 4-2,

4-32049892, Spindle Assembly, 2861AGC Double Sheave

4-4058591, Spindle Assembly, 521E Center 4-20, 4-22058662, Spindle Assembly, 521E/Z 4-14058662, Spindle Assembly, 521E/Z #2 & 4 4-10, 4-28059082, Deflector Assembly, Grass 4-30059126, Door Assembly, #1 Deck Trap 4-2059174, Cylinder Assembly, Deck Lift 4-48061616, Chute Assembly, #5 Deck Grass 4-36061634, Rod Assembly, Rear Deck Height 4-44, 4-46061639, Cover Assembly, #2 Deck 4-12061643, Cover Assembly, #4 Deck Pivoting 4-30061646, Cover Assembly, #4 Pivoting 4-30062051, Washer, Water Shed Pulley 4-17063916, Idler Assembly, EFLW Deck Drive 4-17, 4-24063920, Chute Assembly, #3 Deck Rubber EFLW 4-26063934, Idler Assembly, EFLW Main Drive 3-2, 4-17063940, Wheel Yoke Assembly, EFLW 9 In 4-40063940, Wheel Yoke Assembly, EFLW 9” 4-2, 4-10,

4-17, 4-28, 4-32063944, Cover Assembly, EFLW Main Frame 4-17,

4-18063999, Idler Assembly, EFLW Low 4-2, 4-8064135, Idler Assembly, EFLW High 4-32, 4-34064138, Wheel Assembly, Left Rear EFLW 4-44064142, Wheel Assembly, Right Rear EFLW 4-44064155, Gearbox Assembly, 100EFK 3-4064172, Harness Assembly, 100EFK Main 2-2, 2-8,

2-11064173, Weight Kit, EFK 2-2, 2-8, 2-11064225, Lift Arm Assembly, 100EFK Right 2-2064226, Lift Arm Assembly, 100EFK Left 2-2064227, Lift Assist Assembly, 100EFK Right 2-6064228, Lift Assist Assembly, 100EFK Left 2-6064543, Spindle Assembly, 100EF #3 Deck 4-16, 4-20064547, Cross, Shaft/Gear 3-6064558, Door Assembly, #2 Trap 4-12064568, Door Assembly #3 Deck Trap 4-16064574, Door Assembly, #4 Deck Trap 4-30

064577, Door Assembly, #4 Deck Trap 4-30064580, Baffle Assembly, #4 Blowout 4-30064592, Clutch Assembly, Warner Electric 3-4064661, Door Assembly, #2 Trap 4-12067032, Hose Assembly, 100EFK Hydraulic 2-5, 2-6,

2-11, 2-13067078, Deck Weldment, EFLW #5 4-32067087, Door Assembly, #3 Deck Trap 4-17067734, Deck Weldment, EFK #3 1-8067762, Lift Assist Assembly, 100EFK Right 2-2, 2-4067766, Lift Assist Assembly, 100EFK Left 2-2, 2-4067770, Lock Assembly, Kubota Deck Lift 2-11, 2-14067771, Pedal Weldment, Kubota Lift Lock 2-14067789, Plate, Bumper Mount 2-14067792, Cover Assembly, Left Transition 4-12067942, Kit, 100EFKC CE Hardware 4-52071530, Latch Plate, Kubota 2-14071532, Bushing, Kubota Latch 2-14072105, Keeper Wldmt, 100" Belt 4-16072575, Pedal Pad, Deck Lift Lock 2-14072605, Decal, CE Herald 1-6072724, Hardware Kit, 100EFKC CE 2-10072725, Lift Assist Assembly, 100EFK Right 2-10072725, Lift Assist Assembly, 100EFKC CE Right 2-12072726, Mounting Weldment, 100EFK Frame Right

2-12072728, Lift Assist Assembly, 100EFK Left 2-11072728, Lift Assist Assembly, 100EFKC CE Left 2-12072729, Mounting Weldment, 100EFKC CE Frame

Right 2-12072730, Lift Arm Assembly, 100EFKC CE Right 2-10072737, Lift Arm Assembly, 100EFKC CE Left 2-10072738, Decal Kit, 100EFKC CE 1-660009-60028, Bolt, 5/16-18 x 2 1/4” Hex Head 4-16,

4-5270030-02067, Seal, 1 1/8” ID Trb Bearing 4-4270050-00936, Washer, 5/16” SAE Flat 3-4, 4-12, 4-16,

4-18, 4-26, 4-30, 4-32, 4-3870050-02124, Bearing Cone, TMKN L44643 3-670050-93549, Ring, 3/4” External - External 4-1670050-94047, Plug, 1/4-18 NPT Schd w/3m 3-670050-94190, Bolt, 5/16-18 x 1” Carriage Grade 5 4-26,

4-36, 4-3870060-02447, Washer, 5/8” Standard Flat 4-10, 4-2870060-02853, Fitting, 1/4-28 45 Deg Grease 4-2470060-02853, Fitting, 1/4-28 45 Deg. Grease 4-4270060-04188, Bolt, 5/16-18 x 3/4” Carriage 4-3070070-00171, Nut, 5/8-11 Jam 4-3, 4-3270070-00179, Key, 1/4” Sq x 1-1/2” Long 3-4

ii 100EFKC//021015 Index

Part Number Index

70070-00181, Fitting, 1/4-28 Straight Grease 2-2, 2-10, 4-2, 4-4, 4-10, 4-14, 4-16, 4-20, 4-28, 4-32, 4-48

70080-01223, Bolt, 1/2-13 x 6 1/2” Hex Head Grade 54-44

70080-01765, Pin, 1/2” Dia x 2 1/2” Detent 4-4875596-64130, Abrasion Sleeve, 50” Hyd. Hose 4-5075599-01140, Bolt,1/4-20 x 2” Hex Head Grade 5 4-1675599-01210, Bolt, 5/16-18 x 1/2” Hex Head Grade 5

4-12, 4-3075599-01215, Bolt, 5/16-18 x 3/4” Hex Head 4-3075599-01215, Bolt, 5/16-18 x 3/4” Hex Head Grade 5

4-2, 4-12, 4-16, 4-17, 4-18, 4-30

75599-01225, Bolt, 5/16-18 x 1 1/4” Hex Head Full Thread Gr5 4-6

75599-01225, Bolt, 5/16-18 x 1 1/4” Hex Head Full Thread Grade 5 4-22, 4-52

75599-01240, Bolt, 5/16-18 x 2” Hex Head Grade 5 4-1875599-01315, Bolt, 3/8-16 x 3/4” Hex Head Grade 5 4-1675599-01325, Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5

3-475599-01330, Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5

2-14, 4-4875599-01530, Bolt, 1/2-13 x 1 1/2” Hex Head Grade 5

4-2475599-01540, Bolt, 1/2-13 x 2” Hex Head 4-8, 4-3475599-01540, Bolt, 1/2-13 x 2” Hex Head Grade 5 4-2475599-01550, Bolt, 1/2-13 x 2 1/2” Hex Head Grade 5

4-2, 4-10, 4-16, 4-28, 4-3275599-01560, Bolt, 1/2-13 x 3” Hex Head Grade 5 4-10,


4-2, 4-10, 4-28, 4-3275599-01755, Bolt, 5/8-11 x 2 3/4” Hex Head Grade 5

4-10, 4-2875599-01760, Bolt, 5/8-11 x 3” Hex Head Grade 5 4-10,

4-2875599-01780 , Bolt, 5/8-11 x 4” Hex Head Grade 5 4-2,


2-2, 2-1075599-01880, Bolt, 3/4-10 x 4” Hex Head Grade 5 2-875599-04735, Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5

4-4, 4-14, 4-2075599-31012, Nut, 5/16-18 Hex 4-8, 4-10, 4-28, 4-34,

4-4275599-31015, Nut, 1/2-13 Hex 2-2, 2-10, 4-1675599-31912, Nut, 5/16-18 Nylock Hex 4-32

75599-31912, Nut, 5/16-18 Nylok Hex 3-4, 4-8, 4-16, 4-22, 4-34

75599-31912, Nut, 5/16-18 Nylon Lock Hex 4-675599-31913, Nut, 3/8-16 Hex Nyloc 2-2, 2-10, 2-14,

3-4, 4-2, 4-4, 4-14, 4-20, 4-32

75599-31913, Nut, 3/8-16 Hex Nylock 4-2, 4-4875599-31915, Nut, 1/2-13 Nyl Hex Lock 4-2, 4-10,

4-28, 4-3275599-31915, Nut, 1/2-13 Nylon Hex Lock 4-1675599-31918, Nut, 3/4-10 Nylock 2-8, 2-1075599-32011, Washer, 1/4” SAE Flat 4-1775599-32015, Washer, 1/2 SAE Flat 4-4675599-32015, Washer, 1/2” SAE Flat 2-5, 2-7, 2-13,

3-2, 4-16, 4-24, 4-3475599-32015, Washer, 1/2” SEA FLat 4-875599-32017, Washer, 5/8” SAE Flat 2-4, 2-5, 2-12,

2-13, 4-10, 4-28, 4-4875599-32018, Washer, 3/4” SAE Flat 4-4075599-33011, Washer, 1/4” Split Lock 4-1775599-33014, Washer, 7/16” Split Lock 2-276700-40802, Pulley, 5” OD Idler 4-8, 4-24, 4-3477700-00954, Bolt, M12 x 1.25 x 35mm Hex Head 2-877700-00991, Nut, 10-24 Hex Nylock 2-877700-01242, Bolt, 7/16-14 x 1 1/4” Hex Head Grade 5

2-277700-01387, Bolt, 5/16-18 x 1” Hex Head Grade 5 3-4,

4-26, 4-30, 4-4877700-01456, Bolt, 5/16-18 x 1 1/2” Hex Head FT Grade

5 4-877700-01456, Bolt, 5/16-18 x 1 1/2” Hex Head Grade5

FT 4-3477700-01643, Bolt, 5/8-11 x 3 1/2” Hex Head Grade 5

2-4, 2-1277700-02039, Washer, M12 Flat 2-877700-02040, Washer, 12mm Split Lock 2-877700-02044, Washer, #10 SAE Flat 4-5277700-02767, Rod End, 1/2-20 Female 4-4677700-02769, Spacer, 1/4” Thk Deck Height 2-677700-02770, Key, 1/4” x 2-1/2” 4-14, 4-2077700-02770, Spacer, 5/16” Thick Deck Height 4-44,

4-4677700-02771, Key, 1/4” x 2 1/2” 4-477700-02772, Bushing, 3/4” ID x 1” OD x 1” Oil 3-2,

4-8, 4-24, 4-3477700-02773, Plug, 1/8-27 NPT Schd w/3m 3-677700-02774, Spacer, 3/4” Axle Bolt 4-40, 4-4477700-02775, Cover, 1 3/8”” Hole Plug 4-2, 4-12, 4-30,

4-32

Index 100EFKC//021015 iii

Part Number Index

77700-02776, Washer, Throttle Friction 4-2, 4-3277700-02777, Bolt, 5/16-18 x 2” Elevator 4-10, 4-2877700-02778, Bumper, Rubber Button 4-12, 4-3077700-02779, O-Ring, Spindle 4-6, 4-2277700-02780, O-Ring, 2 7/16" ID x 3/16" Diameter 4-677700-02780, O-Ring, 2-7/16" ID x 3/16" Diameter 4-2277700-02781, Screw, 10-24 x 1/2” Sl Hex Machine 4-4877700-02782, Bolt, 5/16-18 x 1.25” SHCS 3-677700-02783, Screw, 5/16-18 x 3/4” FHSw/Nyloc Patch

B/O 3-477700-02784, Bolt, 5/16-18 x 5” Hex Head Grade 5 4-6,

4-2277700-02785, Bolt, 3/8-16 x 1 1/2” Full Thread Hex

Head 2-1477700-02785, Bolt, 3/8-16 x 3/4” Carriage 4-16, 4-3077700-02786, Bolt, 3/8-16 x 1 1/2” Hex Head Grade 8

3-277700-02786, Bolt, 3/8-16 x 1-1/2” Hex Head Grade 8

4-2, 4-3277700-02787, Bolt, 3/8-16 x 1 1/2” Carriage Gr5 4-1477700-02787, Bolt, 3/8-16 x 1 1/2” Carriage Grade 5 4-477700-02787, Bolt, 3/8-16” x 1 1/2” Carriage Gr5 4-2077700-02788, Bolt, 1/2-13 x 2” Full Thread Grade 5 2-2,

2-1077700-02789, Bolt, 5/8-11 x 2 1/4” Carriage Grade 5

4-4477700-02790, Nut, 1-14 Hex Jam 4-4877700-02791, Nut, 5/16-18 Nylon Locking Jam 4-2,

4-12, 4-26, 4-30, 4-31, 4-32, 4-38

77700-02792, Nut, 3/4-10 Half Nyloc 4-8, 4-3477700-02793, Nut, 3/8-16 Half Nyloc 2-14, 4-1677700-02793, Nut, 3/8-16 Half Nylock 4-3077700-02793, Nut, 3/8-16 Half Nylon Lock 3-277700-02794, Nut, 1/2-13 Half Nyloc 2-4, 2-6, 2-12,

3-2, 4-3477700-02794, Nut, 1/2-13 Half Nylon Lock 4-8, 4-4477700-02794, Nut, 1/2-13 Hex Half Nylon Lock 4-2477700-02795, Nut, #10-24 Keps 4-4877700-02796, Nut, 3/4-16 Hex Nylon Lock 2-277700-02797, Nut, 1/2-20 Hex Jam 4-4677700-02798, Nut, 3/4-10 Stover Swaged 3-2, 4-40,

4-4477700-02799, Nut, 1/2-20 Jam Nyl Lock 4-4677700-02800, Nut, 5/8-11 Jam Nyl Lock 4-3, 4-10,

4-28, 4-32, 4-4877700-02800, Nut, 5/8-11 Jam Nylon Lock 2-4, 2-5,

2-12, 2-1377700-02801, Washer, 5/16” Split Lock 3-4, 4-2, 4-6,

4-10, 4-12, 4-16, 4-17, 4-18, 4-22, 4-28, 4-30, 4-42, 4-48

77700-02802, Washer, 5/16” Star IT 3-477700-02803, Washer, 5/16” x 1 1/4” Fender 4-12, 4-26,

4-30, 4-3677700-02804, Washer, 10mm Split Lock 2-4, 2-6, 2-8,

2-1277700-02805, Washer, 2 1/2” OD x 5/8” ID x 3/16” Std

Flat Znc 4-4, 4-2077700-02805, Washer,2 1/2” ODx5/8” IDx3/16” Std Flat

Znc 4-1477700-02806, Washer, 1/2” Split Lock 4-10, 4-2877700-02807, Pin, 1/8” x 1/2” Roll 4-6, 4-2277700-02808, Screw, #10 x 1/2” Long AB Thrd Slot Hex

Head 4-12, 4-3077700-02809, Tie Wrap, 3/16” x 6 UV Blk 2-877700-02810, Bolt, M10-1.25 x 30mm HHFT 8.8 2-4,

2-6, 2-12, 4-3277700-02810, Bolt, M10-1.25x30mm HHFT 8.8 4-277700-02811, Screw, M10-1.25 x 45 Hx Cap SC 2-4,

2-6, 2-12, 4-10, 4-2877700-02812, Nut, 10mm x 1.25 Nylon 4-2, 4-10, 4-28,

4-3277700-02814, Washer, 1-1/16” x 1-3/4” x 1/8” Znc 4-4077700-02817, Nut, M10-1.25 Free Zinc Plate 4-2, 4-10,

4-28, 4-3277700-02820, Spacer, 1” ID x 1-3/4” OD x 1/4” 4-4077700-02821, Washer, 3/8” Flat SAE 4-3077700-02821, Washer, 3/8” SAE Flat 2-2, 2-1077700-02822, Pin, 3/8” Dia Lynch Locking 4-4077700-02823, Washer, 1.50” x 1.185” x 16Ga 4-6, 4-2277700-02824, Washer, 2.435” x 1.185” x 11Ga 4-6, 4-2277700-02825, Bushing, Vent 1/4” NPT to 1/8” NPT 3-677700-02826, Hose Clutch Stop Bushing 3-477700-02827, Spacer, 5/16” Thick Knurled 4-4677700-02830, Bolt, 5/8-11 x 4 1/2” Hex Head Grade 8

4-4877700-02831, Bolt, 5/8-11 x 1 1/2” Hex Head Full

Thread Grade 5 4-10, 4-2877700-02833, Washer, 3/4” AN Yel/Cad 3-2, 4-8, 4-16,

4-3477700-02835, Bearing Race Insert, 3/4” TRB 4-4277700-02838, Bushing, 1” ID x 1-1/4” OD x 1-1/4”

Flanged 4-4077700-02839, Spacer, Plastic 3/4” OD x .325” ID x 1”

4-1877700-02840, Washer, 1/2” Plain Belleville 4-4, 4-1477700-02841, Spacer, 1 3/4” OD x 1 1/16” ID x 1” 4-40

iv 100EFKC//021015 Index

Part Number Index

77700-02842, End Cap CP 1.500-.187 D#7647 3-677700-02843, Ring, Superior GB Retaining R100 3-677700-02844, Plug, Vent 5 PSI 3-677700-02845, Washer, 1/4” x 1.47” x 1.01 4-2077700-02845, Washer, 1/4” x 1.47” x 1.01” 4-4, 4-1477700-02846, Bushing, .875 Bearing 2-4, 2-1277700-02846, Bushing, .875” Bearing 4-10, 4-2877700-02847, Spring, .72x1.5x.063 Compression 4-4677700-02852, Wheel, Anti-Scalp, 5-5/8" Hole 4-2, 4-3277700-02853, Washer, 2 1/2” x 11/16” x 3/16” Nylon 4-477700-02853, Washer, 2-1/2” x 11/16” x 3/16” Nylon

4-14, 4-2077700-02855, Spacer, 3/4” Wheel Bearing 4-4277700-02857, Nut, 5/8-11 FlexLoc 4-2, 4-10, 4-28,

4-32, 4-4477700-02858, Clamp Plate, Rubber Chute 4-2677700-02859, Bearing Cup, TMKN L44620 3-677700-02860, Decal, 100in - White 1-4, 1-677700-02861, Washer, 3/8” x 1.5”x1.01” 4-1477700-02863, Spring, 1” x 7” Extension 3-2, 4-8, 4-3477700-02864, Bearing, Tapered Roller 3/4” ID 4-4277700-02865, Seal, TC-1.00-1.50-.187 Polyacrylate 3-677700-02866, Clamp, 1” ID Coated 4-1677700-02868, Switch, DPST N/O N/C 4-4877700-02869, Bolt, 3/4-10 x 6” Carriage Grade 5 4-40,

4-4477700-02870, Pivot Bearing, Cover 4-12, 4-3077700-02871, Clutch Wire, Warner Electric 10 inch 3-477700-02872, Bolt, Spindle Single Pulley 4-477700-02873, Seal, 2561 Spindle 4-6, 4-2277700-02875, Support Plate, Chute Top 4-3677700-02876, Plate, Deck Reinforcing 4-4, 4-14, 4-2077700-02877, Spacer, Spindle Bearing 4-6, 4-2277700-02878, Bearing, 6206-2NSE 4-6, 4-2277700-02879, Switch Plate, Hydraulic Cylinder 4-4877700-02880, Blade, 21” x 2 1/2” x 1/4” High Lift 4-4,

4-14, 4-2077700-02881, Orifice, 5/16” OD x .040” ID x 3/8” 4-4877700-02882, Spacer, Bearing 4-10, 4-2877700-02883, Tube, Belt Keeper 4-10, 4-2877700-02884, Bushing, Urethane Pivot 4-10, 4-16, 4-2877700-02886, Clamp Plate, #1 Deck Trap Door 4-277700-02887, Bolt, Spindle Pulley 1/2-13 x 1 3/4” 4-1477700-02887, Bolt, Spindle Pulley 1/2-13x1-3/4 4-2077700-02888, Bearing, 1.25” x 2.25” x .50” 4-10, 4-2877700-02889, Washer, 1/2” Standard Flat 2-4, 2-6, 2-12,

4-2477700-02890, Pulley, 5” OD V-Groove Idler 4-8, 4-16,

4-34

77700-02891, Door, 521E/Z #3 Deck Trap 4-1677700-02892, Belt, Insta-Power 85830 1-8, 4-277700-02893, Plate, Deck Reinforcing 4-6, 4-2277700-02894, Door, #2 Deck Trap 4-1277700-02895, Lock Plate, Hydraulic Cylinder 4-4877700-02897, Stop Weldment, Warner C-Belt Clutch 3-477700-02898, Cover Plate, Right 4-3077700-02901, Pulley, 4 “ OD Idler 3-277700-02902, Guard, 325EF PTO Shaft 3-477700-02903, Belt, Goodyear 85500 1-8, 3-477700-02904, Collar, Spindle Top 4-6, 4-2277700-02906, Clamp Plate, #3 Deck Trap Door 4-1677700-02907, Spring, 1-1/2 OD x 8-1/2 x .195 2-677700-02907, Spring, 1-1/2” OD x 8-1/2” x .195” 4-2477700-02908, Door, #1 Deck Trap 4-277700-02909, Sheave, Double - 2561 Mower 4-4, 4-1477700-02910, Belt, B-128 Deck Drive 1-877700-02911, Chute Tab, Inside Rubber 4-3677700-02912, Plate, EF Superior Gearbox Right 3-477700-02913, Plate, EF Superior Gearbox Left 3-477700-02914, Dampener, Hand Control 4-2, 4-3277700-02915, Guard Weldment, #4 Rear 4-3077700-02916, Guard Weldment, #2 Rear 4-1277700-02917, Hose Assembly, 41.5 90 Deg JIC 4-5077700-02918, Hose Assembly, 48" 90 Deg JIC 4-5077700-02919, Plate Weldment, 521E Idler 4-3477700-02919, Weldment, 521E Idler Plate 4-877700-02921, Weldment, 521E Main Deck Idler 4-2477700-02923, Casting, R100 Tap 3-677700-02924, Housing, R100 Mach Thru 1/8 1/4 3-677700-02925, Shaft, Center Blade Spindle 4-677700-02926, Chute, #5 Right Rubber Grass 4-3677700-02927, Block, Hydraulic Cylinder Pivot 4-4877700-02928, Shaft, Extended Center Blade Spindle

4-2277700-02929, Housing, Spindle 4-6, 4-2277700-02930, Lock Weldment, Deck Latch 4-4877700-02931, Wheel Assembly, 9” x 3.5” Reliance DM

4-42, 4-4477700-02931, Wheel Assembly, 9x3.5 Reliance DM

4-4077700-02932, Cylinder, Hyd. Deck Lift 4-4877700-02933, Cross Assembly, Shaft/Gear R100 3-677700-02934, Cylinder Assembly, Deck Lift 4-4877700-02935, Relay, ISO 12V Coil w/Diode 2-877700-02937, Cover Plate, Left 4-1277700-02938, Cover, #1 Deck 4-277700-02939, Guard Weldment, #2 Front 4-1277700-02940, Guard Weldment, #4 Front 4-30

Index 100EFKC//021015 v

Part Number Index

77700-02941, Cover Weldment, #5 4-3277700-02943, Support Plate, Chute Side 4-3677700-02945, Spring, Wheel Yoke 1-0 Urethane 4-4077700-02946, Washer, 1-3/4” x .51” x 1/4” 4-2077700-02947, Decal, 3682/96 Gearbox Fluid 1-4, 1-677700-02948, Lift Arm Weldment, 100EFK Right 2-2,

2-1077700-02950, Plate, 100EFD Link 2-677700-02952, Mounting Weldment, 100EFK Frame 2-677700-02955, Baffle Weldment, EFLW #1 & 3 Deck

4-1677700-02957, Rubber Chute, #3 Deck EFK 4-2677700-02958, Cover, EFLW Front Frame 4-1677700-02959, Idler Weldment, EFLW Main Drive 3-277700-02962, Yoke Weldment, EFLW 9 In 4-4077700-02963, Cover, EFLW Main Frame Rear 4-1877700-02964, Cover Weldment, EFLW Front LT Frame

4-1877700-02965, Cover, EFLW Front RT Frame 4-1877700-02966, Deck Weldment, EFLW #2 1-877700-02967, Hinge Weldment, EFLW #2 Deck 4-1077700-02969, Deck Sub-Assembly, EFLW #1 1-8, 4-277700-02970, Deck Weldment, EFLW #4 1-877700-02971, Hinge Weldment, #4 EFLW Deck 4-2877700-02972, Deck Sub-Assembly, EFLW #5 1-8, 4-3277700-02973, Wheel Weldment, Left Rear EFLW 4-4477700-02974, Wheel Weldment, Right Deck EFLW 4-4477700-02975, Bracket, Switch EFK 2-877700-02976, Wiring Harness, 100EFK Main 2-877700-02977, Plate, EFK Spring Mount 2-4, 2-6, 2-1277700-02978, Chain, 5/16” x 9 Links 2-677700-02979, Bushing, 20 ID x 28 OD x 25 Oil 2-2, 2-1077700-02980, Hardware Kit, 100EFK 2-277700-02981, Cover, #2 deck Right Sliding 4-1277700-02982, Cover, #1 Deck Sliding 4-1277700-02983, Cover, #4 Deck Sliding 4-3077700-02984, Cover, #5 Deck Sliding 4-3077700-02985, Guard, Belt Cover 4-2, 4-3277700-02986, Sheave, Triple - 100 Outfront Mower 4-2077700-02988, Gearbox, Superior R100-9AAE-M0023

3-4, 3-677700-02989, Clutch, Diesel Mower 3-477700-02991, Hose Assembly, 1/4” Hyd x 42-1/2" 2-5,

2-6, 2-13, 4-5077700-02992, Abrasion Sleeve, 41-1/2” Hyd. Hose 2-5,

2-6, 2-13, 4-5077700-02993, Abrasion Sleeve, 43-1/2” Hyd. Hose 4-5077700-02994, Fitting, Hyd QD Male 2-5, 2-6, 2-1377700-02996, Rod, Deck Lift Lock 4-46

77700-03003, Bolt, M12 x 1.75 x 50mm Hex Head FT CL10.9 2-4, 2-6, 2-12

77700-03004, Bolt, 1/2-13 x 2 3/4” Hex Head Grade 53-2

77700-03004, Bolt, 1/2-13 x 2-3/4” Hex Head Grade 52-4, 2-5, 2-6, 2-12, 2-13

77700-03005, Nut, M12 x 1.75 Hex Nylock 2-4, 2-6, 2-12

77700-03006, Nut, M12 x 1.75 Free 2-4, 2-6, 2-1277700-03007, Washer, 1/2” Nord-Lock 4-2077700-03014, Bolt, #10-24 x 1/2” Ph Pan Hd, Type 23

2-877700-03015, Hinge, 521E Sliding Cover 4-12, 4-3077700-03016, Deflector Plate, #5 Deck Grass 4-3077700-03019, Supplemental Harness, 100EF 2-3, 2-1177700-03120, Bumper, Table 2-2, 2-1077700-03121, Fitting, 1/4” NPT x 1/4” JIC w/5/16 Tap,

Elbow 4-4877700-03122, Blade Disc, Anti-Scalp 4-4, 4-14, 4-2077700-03123, Fitting, 1/4” JIC x Male Pipe Run Tee- Tap

4-4877700-03124, Mulching Plate, #3 4-3877700-03126, Support Plate, Chute Top 4-3677700-03127, Blade, 21” x 2 1/2” x 1/8” Low-Lift Ultra

4-4, 4-14, 4-2077700-03128, Plate, EFK Weight Bracket Angle 2-877700-03129, Bracket, 100EFK Hose Mtg 2-5, 2-6,

2-1377700-03130, Sleeve, .875” x 1.39” Lg Bushing 4-10,

4-2877700-03131, Decal, Danger - Rotating Blades Bilingua

1-4, 1-677700-03132, Decal, Danger, Thrown Objects Bilingual

1-4, 1-677700-03133, Bar, 100EFKC Spring Installation 2-3,

2-1177700-03134, Rivet, 3/16” Dia x 3/8-1/2 Grip Range Pop

4-2, 4-3277700-03134, Rivet, 3/16” Dia x 3/8-1/2” Grip Range

Pop 4-5277700-03135, Screw, M4-.7 x 65 SHC 2-2, 2-11, 2-1477700-03135, Screw, M4-.7x65 SHC Zinc 3-877700-03136, Nut, M4-.7 Prev Torq 2-3, 2-11, 2-1477700-03136, Nut, M4-.7 Prev Torq Znc 3-877700-03137, Blade, 21” Low-Lift 4-4, 4-14, 4-2077700-03138, Blade, 21” Gator Mulching 4-4, 4-14,

4-2077700-03139, PTO Shaft Assembly, Kubota 24 In 2-3,

2-11, 3-8

vi 100EFKC//021015 Index

Part Number Index

77700-03140, Washer, 7/16” Nord-Lock 3-477700-03141, Screw, 7/16-20 x 2-3/4” Hex Head Grade

8 3-477700-03142, Nut, 1/2-13 Jam 2-4, 2-6, 2-12, 4-2477700-03143, Mulching Plate, #5 Deck 4-3877700-03152, Switch Plate, Hydraulic Cylinder Shim 2-877700-03153, Nut, 100EF Hinge Cam Adjust 4-10, 4-2877700-03622, Bracket Weldment, EFK Weight 2-877700-03623, Spacer, 3/4” x 1 1/2” x 1/4” 2-2, 2-1077700-03624, Lift Arm Weldment, 100EFK Left 2-2,

2-1077700-03691, Pin, 7/16” Dia Lynch Locking 4-4877700-036921, Chain, 5/16” x 5 Links 4-4877700-03693, Mounting Weldment, 100EFK Frame

Right 2-677700-03694, Clamp Plate, #3 Chute EFK 4-2677700-03696, Shim, 1/5” Rocker 4-2, 4-3277700-03697, Rocker Weldment, #1 EFLW 4-277700-03698, Rocker Weldment, #5 EFLW 4-3277700-03699, Kit, Cross Bearing S1 22x54 Zerk In Cap

3-877700-03700, Yoke, Outer Self Lock Kubota 10 Spline

3-877700-03701, Yoke, Outer Pin Lock Mower 20 Spline

3-877700-03702, Ring, Bearing B&P Outer Shield Cone

Fml 3-877700-03703, Ring, Bearing B&P Outer Shield Cone

Male 3-877700-03704, Cone, B&P Outer Shield 3-877700-03705, Sleeve, Outer Shield 049615 Female 3-877700-03706, Decal, Bondioli Sleeve 3-877700-03707, Decal, Danger Bondioli Outer Drive Tube

3-877700-03708, Sleeve, Inner Shield 049615 Male 3-877700-03709, Screw, B&P Outer Shield Cone 3-877700-03711, Kit, Spring Lock Collar Rebuild 3-877700-03712, Kit, Safety Shield 049615 Complete 3-877700-03713, PTO Shield Retaining Chain, Bondiol

2-11, 2-14, 3-877700-03714, PTO CE Label Kit, Bondioli 3-877700-03749, Washer, 3/8x1-1/2 x 1/8” Thk Hardened

4-2, 4-3277700-03751, Pad, Seat/Hood Rubber Bumper 2-1477700-038581, Bolt, M12 x 1.75 x 75mm Hex Head 2-677700-03859, Boss, Spring Spacer 2-277700-04426, Mounting Weldment, 100EFK Frame

Right 2-477700-04427, Plate, 100EFD Link 2-4, 2-12

77700-04428, Spring, Counter Balance 2-4, 2-1277700-04429, Chain, 5/16” x 7 Links 2-4, 2-1277700-04430, Spacer, .53ID x 1-1/4 OD x 1-1/16 Long

2-4, 2-5, 2-6, 2-12, 2-1377700-04431, Washer, Motor Mount 2-4, 2-1277700-04432, Sleeve, 7/8” OD x 2.20 Long Bushing 2-4,

2-5, 2-12, 2-1377700-04433, Mounting Weldment, 100EFK Frame 2-477700-04434, Deck Weldment, EFLW #1 4-277700-04435, Washer, Water Shed Pulley 4-8, 4-3477700-04436, Clamp Plate, #2 Deck Trap Door 4-1277700-04437, Door, #2/4 Deck Trap 4-12, 4-3077700-04438, Clamp Plate, #2 Deck Trap Door 4-1277700-04439, Door, #2 Deck Trap 4-1277700-04440 2, Cover, EFLW #3 Deck Right 4-1677700-04441 2, Cover, EFLW #3 Deck Left 4-1677700-04442, Clamp Plate, #3 Deck Trap Door 4-1777700-04443, Door, 521E/Z #3 Deck Trap 4-1777700-04444, Baffle Weldment, #4 Blowout 4-3077700-04448, Bolt, 1/4-20 x 2 1/4” Hex Head Full

Thread Grade 5 4-5277700-04449, Nut Assembly, 5/16-18 Cover Retaining

4-5277700-04450, Spacer Assembly, Cover Retaining 4-5277700-04451, Nut Keeper, Cover Retaining 4-5277700-04452, Nut Assembly, 1/4-20 Cover Retaining

4-5277700-05514, Door, #4 Deck Trap 4-3077700-05515, Clamp Plate, #4 Trap Door 4-3077700-05516, Plate, Bearing Extension EFKC 4-10,

4-2877700-05517, Decal Kit, 100EFKC 1-477700-05518, Dam Kit, 100” Mulching 4-387J245-58120, Fitting, Grease 90 Deg. 1/4-28 4-8, 4-16,

4-34FF05006-153, Bolt, 5/16-18 x 1-1/2 Carriage Grade 5 4-36F05007-230, Bolt, 3/8-16 x 2 3/4” Full Thread Hex Head

Grade 2 3-4F05007-87, Bolt, 3/8-16 x 1” Hex Head Grade 5 4-10,

4-28F05009-60, Bolt, 7/16-14 x 1 3/4” Hex Head G8 2-10F05010-1, Nut, 3/8-16 Hex 3-4F05010-103, Nut, 3/4-10 Nylock 2-10F05010-135, Nut, 7/16-14 Nylock 2-10F05010-156, Nut, 1/4-20 Half Nylock 2-14F05010-164, Nut, 7/16-14 Jam 2-10F05010-221, Nut, 5/16-18 Flanged Hex Nylock 4-36F05010-222, Nut, 3/8-16 Flanged Hex Nylock 4-11,

Index 100EFKC//021015 vii

Part Number Index

4-28F05010-224, Nut, 5/8-11 Flanged Hex Nylock 4-10,

4-28F05011-3, Washer, 3/8” Flat SAE 2-14F05011-35, Washer, 7/16” Standard Flat 2-10F05011-68, Washer, 1/2 Standard Flat 4-17F05011-73, Washer, 7/8” SAE Flat 4-44F05011-9, Washer, 1/2 Split Lock 4-17IIS-0331, Instruction Sheet, 100EFKC CE Hardware Kit

4-52NN/A, Decal, Kubota Serial Plate 1-4, 1-6WW25TS04073, Bearing Cone, TMKN L44643 3-6W25TS04074, Ring, 3/4” External - External 4-16W25TS04075, Fitting, 1/4-28 Straight Grease 2-2, 2-10,

4-2, 4-4, 4-10, 4-14, 4-16, 4-20, 4-28, 4-32, 4-48

W25TS04076, Bolt, 1/2-13 x 6 1/2” Hex Head Grade 54-44

W25TS04077, Abrasion Sleeve, 50” Hyd. Hose 4-50W25TS04078, Bolt, 5/16-18 x 1/2” Hex Head Grade 5

4-12, 4-30W25TS04079, Bolt, 5/16-18 x 3/4” Hex Head Grade 5

4-2, 4-12, 4-16, 4-17, 4-18, 4-30

W25TS04080, Bolt, 5/16-18 x 1 1/4” Hex Head Full Thread Gr5 4-6, 4-22, 4-52

W25TS04081, Bolt, 3/8-16 x 3/4” Hex Head Grade 54-16

W25TS04082, Bolt, 3/8-16 x 1 1/4” Hex Head Grade 53-4

W25TS04084, Bolt, 1/2-13 x 2 1/2” Hex Head Grade 54-2, 4-10, 4-16, 4-28, 4-32

W25TS04085, Bolt, 1/2-13 x 3” Hex Head Grade 5 4-10, 4-28

W25TS04086, Bolt, 5/8-11 x 2 3/4” Hex Head Grade 54-10, 4-28

W25TS04087, Bolt, 5/8-11 x 3” Hex Head Grade 5 4-10, 4-28

W25TS04088, Nut, 5/16-18 Hex 4-8, 4-10, 4-28, 4-42W25TS04089, Nut, 1/2-13 Hex 2-2, 2-10, 4-16W25TS04091, Nut, 5/16-18 Nylok Hex 3-4, 4-6, 4-8,

4-16, 4-22, 4-32, 4-34W25TS04092, Nut, 3/8-16 Hex Nyloc 2-2, 2-10, 3-4,

4-2, 4-4, 4-14, 4-20, 4-32, 4-48

W25TS04093, Nut, 1/2-13 Nyl Hex Lock 4-2, 4-10, 4-16, 4-32

W25TS04095, Washer, 5/8” SAE Flat 2-4, 2-5, 2-12, 2-13, 4-10, 4-28, 4-48

W25TS04096, Washer, 3/4” SAE Flat 4-40W25TS04098, Washer, M10 Flat 2-8W25TS04099, Bolt, M10 x 1.25 x 35 2-8W25TS04099, Fitting, Grease 90 Deg. 1/4-28 4-8, 4-16,

4-34W25TS04100, Washer, 1/2” SAE Flat 2-5, 2-7, 2-13,

3-2, 4-8, 4-16, 4-24, 4-34, 4-46

W25TS04101, Pulley, 5” OD Idler 4-8, 4-24, 4-34

viii 100EFKC//021015 Index

Documents

RCL100F-F36 100 Flex Deck Parts Manual - Lastecgateway.lastec.com/manuals/Parts/100EFKC (Kubota).pdf · General Information 1 How To Use The Parts List 1-2 Mower//021015 General Information