RC siemens britmn

Installation and TestRadio Commander BR 6.0

Installation Test Manual ITMN

A50023-X4008-A1-2-7630

2 A50023-X4008-A1-2-7630

Installation Test Manual ITMN Installation and TestRadio Commander BR 6.0

! Important Notice on Product SafetyDANGER - RISK OF ELECTRICAL SHOCK OR DEATH - FOLLOW ALL INSTALLATION INSTRUC-TIONS.The system complies with the standard EN 60950 / IEC 60950. All equipment connected to the systemmust comply with the applicable safety standards. Hazardous voltages are present at the AC powersupply lines in this electrical equipment. Some components may also have high operating tempera-tures. Failure to observe and follow all installation and safety instructions can result in seriouspersonal injury or property damage. Therefore, only trained and qualified personnel may install andmaintain the system.

The same text in German:Wichtiger Hinweis zur ProduktsicherheitLEBENSGEFAHR - BEACHTEN SIE ALLE INSTALLATIONSHINWEISE.Das System entspricht den Anforderungen der EN 60950 / IEC 60950. Alle an das SystemangeschlossenenGerte mssen die zutreffenden Sicherheitsbestimmungen erfllen. In diesen Anlagen stehen dieNetzversorgungsleitungen unter gefhrlicher Spannung. Einige Komponenten knnen auch einehohe Betriebstemperatur aufweisen.Nichtbeachtung der Installations- und Sicherheitshinweise kann zu schweren Krperverletzungen oderSachschden fhren. Deshalb darf nur geschultes und qualifiziertes Personal das System installierenund warten.

Epilepsy Warning:With a very small percentage of persons it can come to epileptic attacks, if they expose themselveslight frequencies, and flickering sources of light. Certain light frequencies in monitor backgrounds cancall forth at these persons an epileptic attack. Certain circumstances can call forth up to now unrec-ognized epileptic symptoms at persons, who had up to now no epileptic prehistory. Ask your doctorbefore you are working with computers, if you or any of the members of your family suffer fromepilepsy. Interrupt the work immediately and locate the doctor before you renewed work, if you ascer-tain any of the following symptoms during the work at yourself. Daze blurred vision, eyes- or musceltwitches, agnosia, lost of orientation, involuntary movements or cramps.

Trademarks:All designations used in this document can be trademarks, the use of which by third parties for theirown purposes could violate the rights of their owners.

Copyright (C) Siemens AG 2001-2002Issued by the Information and Communication Networks GroupHofmannstrae 51D-81359 Mnchen

Technical modifications possible.Technical specifications and features are binding only insofar asthey are specifically and expressly agreed upon in a written contract.

A50023-X4008-A1-2-7630 3


Installation Test Manual ITMNIssues

IssuesChange indications (Ind.):N = new; G = modified; 0 = deleted;

Document Title Page(s) Issue/Ind.ITMN:RC 6.0 . . . . . . . . . 1...244 2 / N

This document consists of a total of 244 Pages.

Reason for Update

Issue History

Chapter/Section Reason for Update

whole book

IssueNumber

Date ofIssue

Reason for Update

1 June 2002 B6002 July 2002 The procedure for BagdeReader is added.

The procedure for Working with Scheduler is added.The procedure for Updating Toolset is added.The procedure for Upgrading SW load is added.The procedure for Updating OMP/OMT HW is added.The procedure for Installation Tarantella Server is added.The procedure for Installation External Backup Server isadded.The procedure for How to Install Citrix Metaframe isadded.Description of Configuration Wizard Scrpt is added.Some error correction in general are made.

4 A50023-X4008-A1-2-7630

Installation Test Manual ITMNIssues


A50023-X4008-A1-2-7630 5


Installation Test Manual ITMNContents

Contents1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91.2 Purpose of the document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91.3 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91.4 Workflow for the CD based Installation of Radio Commander . . . . . . . . . . 101.5 CE declaration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111.6 Freeware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2 Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132.1 Check Delivered SW and Licenses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152.2 Installation of OMT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192.3 Installation of OMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392.4 Activate the Radio Commander . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 612.5 Installation of NED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 652.6 Installation of a Tarantella Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 832.7 Installation of an External Backup Server . . . . . . . . . . . . . . . . . . . . . . . . . 1032.8 Installation of a X-Terminal Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1232.9 Create New UNIX Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1452.10 Installing Database under OMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1472.11 New Database Schema (schema update) . . . . . . . . . . . . . . . . . . . . . . . . 1492.12 New OMP Load with Database Delete and Create. . . . . . . . . . . . . . . . . . 1532.13 Installation of DBAEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1552.14 Installation of the Badge Reader. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1632.15 Double Monitor Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1672.16 Add a new OMT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1692.17 How to Install Citrix Metaframe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1712.18 Flashing Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1732.19 Uninstall the Radio Commander Load . . . . . . . . . . . . . . . . . . . . . . . . . . . 1752.20 How to Start/Stop the OMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1772.21 How to Start/Stop the OMT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1792.22 How to Start a GUI Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1812.23 How to Create Printers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1832.24 How to Work With Scheduler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1912.25 How to Update Toolset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1952.26 How to Upgrade SW Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1972.27 How to Update OMP/OMT Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201

3 Appendices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2033.1 Structure of the directories of the RC . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2033.1.1 CD names for CD based installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2053.2 Scripts and configuration files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2053.2.1 ium_configuration.cfg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2053.2.2 omcconf.txt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2103.2.3 sfg_processlistfile_omp/omt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2103.2.4 RC Configuration Wizard Script . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2133.3 Main Commands of Vi and Vedit Editors . . . . . . . . . . . . . . . . . . . . . . . . . 2173.4 Recovery from nonstandard situation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219

6 A50023-X4008-A1-2-7630

Installation Test Manual ITMNContents


3.5 Installation of Printer Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2213.6 Connection between OMP and NMC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2213.7 Table of SW-Licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2223.8 Some Interesting Links. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2263.9 Update of Flash PROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2273.10 Additional Operator Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2363.10.1 Remote OMT Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2363.10.2 PCM communication board configuration . . . . . . . . . . . . . . . . . . . . . . . . . 2383.10.3 The volume manager management in Radiocommander . . . . . . . . . . . . . 2383.10.4 Router configuration for O-link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2393.10.5 PrinterPort parameter in printer creation . . . . . . . . . . . . . . . . . . . . . . . . . . 2403.10.6 Format action for floppy MOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2403.10.7 OMCP installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241

4 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243

A50023-X4008-A1-2-7630 7


Installation Test Manual ITMNIllustrations

IllustrationsFig. 1.1 Flowchart for CD based installation of Radio Commander (recommenda-

tion) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Fig. 2.1 DBAEM Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155Fig. 3.1 Network scenarios for NMC connections. . . . . . . . . . . . . . . . . . . . . . . 221

8 A50023-X4008-A1-2-7630

Installation Test Manual ITMNIllustrations


A50023-X4008-A1-2-7630 9


Installation Test Manual ITMNGeneral

1 General1.1 Introduction

The Radio Commander (RC) is the Operation and Maintenance system for the BaseStation Systems (BSS) for GSM networks. The Radio Commander is composed of twosubsystems: the Operation and Maintenance Processor (OMP) and the Operation andMaintenance Terminal (OMT). The two subsystems are connected by means of a LAN(Local Area Network) configuration.The OMP for GSM networks is connected to the Base Station Systems (BSS) by a linkthat is implemented either by means of a point-to-point connection or by the NewBridgeboard.The connectivity with remote RC is ensured by the X.25 Router whose routing table isset by installation and configuration through the configuration tool.Even if the RC system is inserted in a pre-existent network, functionality is ensured bythe Bridge module, whose configuration enables or disables access from and to hostswhich are external to the RC network segment.

1.2 Purpose of the document

The purpose of the document is to provide all the information necessary for the correctset up of the Radio Commander. This includes checking the installed hardware (ifnecessary) and the correct installation of both the OMT and the OMP software.

1.3 Precautions

The power supply is 220 V for all of the components, but for the US and Asian marketsthe power supply is 110 V for all of the components used on the desk and 220 V for thecomponents installed on the rack. When working with the devices observe the warning indications. During the removal of components/modules turn off the devices. Display a signboard indicating that maintenance work is being performed. The operator requires a thorough knowledge of the composition and operation of the

device and must be a qualified electrician.All devices of the RC system must be correctly turned on/off according to the relevantoperating procedures. For the OMP, the correct shutdown procedures must be executedbefore turning off the power supply of the OMP.In order to avoid damages, turn off each device when making any changes, such as theremoval and/or replacement of modules and/or components.In order to avoid any damage while handling electrostatic sensitive components, theuser should wear an antistatic bracelet grounded with a cord. All electrostatic sensitivecomponents are labelled as such.

10 A50023-X4008-A1-2-7630



1.4 Workflow for the CD based Installation of Radio Commander

The CD based installation for Radio Commander will be made with CDs. For this instal-lation, you needs the direct access (as root) to the OMP/OMT work stations.

Fig. 1.1 Flowchart for CD based installation of Radio Commander (recommenda-tion)

For the installation you have several CDs. For the names of the CDs see 3.1.1. You caninstall OMP and OMTs in parallel. In this manual the installation is described the recom-mended way for installation.

A50023-X4008-A1-2-7630 11



1.5 CE declaration

1.6 Freeware

To the extent the Software includes free software generated and made accessible freeof charge to everyone by third parties, such free software and any specific terms andconditions thereof are described in more detail in the technical specification of the freesoftware. Regardless of such specific terms and conditions, Siemens assumes fullresponsibility towards the customer for all obligations under this contract/agreementexcept stated herein otherwise.

i The CE declaration of conformity for the product will be fulfilled if the setup and cablingis undertaken in accordance with the specification in the manuals and the documenta-tion listed there, such as mounting instructions, cable lists etc. Where necessary,account should be taken of project-specific documentation.Deviations from the specifications or independent changes during setup, such as useof cable types with lower screening values, for example, can lead to the CE require-ments being violated. In such cases the CE declaration of conformity is invalidated andthe responsibility passes to the person who has caused the deviations.

12 A50023-X4008-A1-2-7630



A50023-X4008-A1-2-7630 13


Installation Test Manual ITMNProcedures

2 ProceduresIn the following pages all the procedures are described.

Activation of the previous software version or load is not possible without new installa-tion if the new software version or load runs not correctly.

i The Radio Commander supports only new releases from BR6.0 onwards: the olderreleases has to be updated for the release BR6.0 onwards.These particular cases will be clearly specified.

14 A50023-X4008-A1-2-7630

Installation Test Manual ITMNProcedures


A50023-X4008-A1-2-7630 15


Installation Test Manual ITMNCheck Delivered SW and Licenses

2.1 Check Delivered SW and Licenses

You have to order some licenses before the SW can be installed:Licenses are necessary for the several SW packages (in detail see 3.7 Table of SW-Li-censes).Separate licenses are required for each client to be installed!In the following a step by step procedure is described to get the licenses from SUN.

1 Collect all the "Proof of License CertificatesThese sheets are delivered with your SW packages. Each sheet contain the fol-lowing information about the SW package: the product name of the SW package the version of the product of the SW package the rights to use and the serial number of the SW package

2 Collect the informationFor each client you need the following information: the hostname of the client the host-ID of the client (MAC-address) the product name(s) of the SW package(s) the version of the product(s) of the SW package(s) and the serial number(s) of the SW package(s)

16 A50023-X4008-A1-2-7630



3 Request the licenses from SUNWrite an email to SUN Micro Systems to request the license files. Below yousee an example for the content of the mail.

Normally you will get the licenses from SUN Micro Systems within one day. Ifyou need the licenses very urgently, you can make a telephone call to SUN. Thelicenses will be available then within half an hour. For the telephone numberfrom SUN check the following internet page: http://www.sun.com/licensing/. Ineach case you needs a fax address or better a e-mail address, that SUN couldgive the response to you.

4 Make the licenses_combined FileSUN Micro Systems will send you back the licenses in the form of one or moreASCII files. Combine the contents of the ASCII files in one ASCII file This file must not contain a empty line The entries SERVER and DAEMON are allowed only one time in the file Transfer this ASCII file to your SUN workstation Use the tool "dos2unix" to convert the file into UNIX format (this tool works

only with a Solaris computer, e.g. the OMT, not with a Windows PC!) Rename this file to "licenses_combined"An example of a "licenses_combined" file you can see in + ......3.7 Table of

SW-Licenses

A50023-X4008-A1-2-7630 17



5 Bring the licenses File to your OMT

Now store the file licenses_combined in /tmpb cp //licenses_combined /tmp/licenses_combined

In this way create the licenses_combined file for each client (OMP or OMT) withall the required licenses.

6 How to put the licenses_combined to your OMPRegarding that the OMP has no floppy drive, there are several ways to put yourlicenses_combined file to your OMP: You has the possibility to use any SUN workstation in the LAN, to transfer the

licenses_combined file to your OMP per ftp. You install first an OMT (which has a floppy drive) and afterwards you install

the OMP until the SUN Solaris 2.6 Operating system is completed. Now youcan create and transfer your licenses_combined file per ftp from your OMT tothe OMP. (This is the recommended method, see below.)

iYour OMT must be installed, before you can store the licenses_combined file on it.

iUp to now, only the OMP needs above mentioned licenses!

18 A50023-X4008-A1-2-7630



Return to calling procedure

END

A50023-X4008-A1-2-7630 19


Installation Test Manual ITMNInstallation of OMT

2.2 Installation of OMT

This procedure is intended to provide informations on how to install the Solaris 2.6 oper-ating system and the RC application SW on an OMT Sun Workstation. (For further infor-mation about the OS installation, refer to Solaris 2.6 System Administrator's Manual).With reference to the release documentation, check that you have all necessary CDs foryour installation.If there a NIS server is used, check whether the NIS client is installed (is a part of Solaris2.6 installation).If you have several CD-sets, all of the OMTs can be installed at the same time. EachOMT can installed in the same way (as described in this procedure).

This procedure is used in the following cases: for first time installation of the operating system; when the system is unable to work, or cannot perform a boot as a consequence of

an unrecoverable situation;The following installation works as well for CPUs with more than 400 MHz. Therefore nospecial CD is necessary anymore.

i You must be a superuser (root) for the OMT to perform all the steps in this procedure.

i Because of the OMP has no floppy drive, we recommend, that you first install one OMT(the OMTs have a floppy drive). From the installed OMT you can then transfer your file"licenses_combined" to the OMP. The OMP must have installed with the OperatingSystem (SUN Solaris 2.6) for this transfer.

i Be aware: In the procedure are some very long commands, which you have to enter ina UNIX terminal window. Be aware, that these commands can extend over severallines in this manual!

i Be sure that the tray of the CD-ROM drive is not blocked while the whole installationprocedure, because of sometimes the tray opens automatically, triggered by the instal-lation routine.

20 A50023-X4008-A1-2-7630



1 Installation of Solaris Operating Systemb Disconnect the LAN cable and ignore every warning message about the "Link

Down - cable problem".Insert the CDROM labeled with CD1. Enter break command or [F5] to get the"ok"-prompt:

b [STOP] Aand then enter at the "ok" prompt:

b boot cdrom [ENTER]While you are waiting you should get something like:

Boot device ...SunOS ...

... and a rotating slash. Then opens a window "Solaris Install Console" withe themessage in it:

The system is coming up. Please wait.

Continue with h...2

A50023-X4008-A1-2-7630 21



2 Select Language and LocaleA new window opens:

Select a Language and Locale

b Please select "English (0)" for languages and "USA-English (ISO-8859-1)(9) forLocales with the mouse.

b Push [Continue]The next window on the screen is displayed:

The Solaris Installation Program


Identify This System


Host Name

b Click with the mouse into the host name text field and enter the hostname of thisOMT (e.g. "omt99") using the keyboard.


Network Connectivity

b Set it to "yes".b Push [Continue]

Continue with h...3

3 Do you have several Network Interfaces?If you have only one network interface, continue with ... h...4If in your OMT are several network interfaces, then the following window opens:

Primary Network Interface

b Select your network interface (e.g. hme0), which is connected to the LAN.b Push [Continue]

Continue with h...4

22 A50023-X4008-A1-2-7630



4 Enter the IP Address of your OMTThe next window on the screen is displayed:

IP Address

b Click with the mouse into the IP address text field and enter the IP address ofthis OMT (e.g. "192.168.1.37").


Confirm Information

b Push [Continue] or correct your inputs.The next window on the screen is displayed:

Name Service

If you want to use a NIS. h...5 If you do not want to use a NIS. h...6

5 Only for using NISb Select "NIS" for the installation -> please refer to your customer network infra-

structure or needs!b Push [Continue]

The next window on the screen is displayed:

Domain Name (only for NIS/NIS+)

b Enter your NIS/NIS+ domain name (must be provided by the customer).b Push [Continue]


Name Server

b Select "Find One".b Push [Continue]


Confirm Information

b Push [Continue] or correct your inputs.Continue with... h...7

A50023-X4008-A1-2-7630 23



6 If there is no NISb Select [X] None.b Push [Continue]


Confirm Information

b Push [Continue] or correct your inputs.Continue with... h...7

7 Do you have a Subnet?The next window on the screen is displayed:

Subnets

Please refer to your customer network infrastructure or needs!Do you have a subnet? Y h...8

N h...9

8 Only if you have a Subnetb If you have a subnet, select "yes".b Push [Continue]


Netmask

b Enter the netmask of your OMT, e.g. "255.255.255.240".Continue with... h...10

9 If you have no Subnetb If you do not have a subnet, select "No".b Push [Continue]

Continue with... h...10

24 A50023-X4008-A1-2-7630



10 Continue the OS-InstallationThe next window on the screen is displayed:

Time Zone

b Select as time zone "Offset From GMT".

b Push [Set...]The next window on the screen is displayed:

Offset from GMT

b Move the button on the "0" position (default).b Push [Continue]


Date and Time

b Correct your local date and time if necessary. Therefore move the cursorthrough the fields with the arrow keys and edit the values.


Confirm Information

b Push [Continue] or correct your inputs.The next window "Solaris Install Console" displays in the last line:

.

.

Begin script install_beginn execution completed.

b Please reconnect the LAN cable.A new window opens:

Solaris Interactive Installation

Continue with ... h...11

iPay attention to set the same time zone on both OMP and OMT, otherwise date andtime requests will not be aligned and RC software will give time stamps not aligned asa result of a measurement or a log.

A50023-X4008-A1-2-7630 25



11 Solaris Interactive Installationb Push [Initial] (default)b Push [Continue]


Allocate Client Services

b Push the [Continue] button.

Select Languages

Do not select anything. Continue the installation in English.b Push [Continue]


Select Software

b Select the "Entire Distribution for Radio Commander" with the toggle button.b Push [Continue]


12 Customize the File System and Disk LayoutThe next window on the screen is displayed:

Select Disks

The following steps depend on your hard disk configuration of the OMT: If your hard disk size is less than 2GB h...13 If your hard disk size is 2GB or greater. h...14

26 A50023-X4008-A1-2-7630



13 Partitioning If Your Hard Disk Size is Less Than 2GBThe next window on the screen is displayed:

Preserve Data

Because of this is a installation from scratch, do not select anything andb Push [Continue]


Automatically Layout File Systems?

b Push [Manual Layout]The next window on the screen is displayed:

File System and Disk Layout

b Push [Customize...]The next window on the screen is displayed:

Customize Disk: c0...d0

b Enter "swap" partition in slice 1 and set the Size (MBs) to 256, enter root parti-tion "/" in slice 0 and set the Size to the maximum (=overlap - swap; take thevalue from the line "free".).

b Push [OK]You are back in the window:


If you find here something wrong, you can return with [Customize...]-button andcorrect your input.

Slice Mount Point Size (MB) 0 / 1 swap 256 2 overlap 3 4 5 6 7

Name Partition MB filesys1=rootdisk.s0 / filesys2=rootdisk.s1 swap 256

A50023-X4008-A1-2-7630 27



b If you are finished with customizing your disk, push [Continue].Continue with ... h...15

28 A50023-X4008-A1-2-7630



14 Partitioning If Your Hard Disk Size is 2GB or Greater.The next window on the screen is displayed:

Preserve Data













Name Partition MBfilesys1=rootdisk.s0 / filesys2=rootdisk.s1 swap 1024

A50023-X4008-A1-2-7630 29




15 File System and Disk LayoutThe next window on the screen is displayed:

Mount Remote File Systems?

b Push [Continue]

Profile

b Confirm settings and push [Begin Installation].The next window on the screen is an information window without a title:

b Push [Auto Reboot]The next window on the screen "Installing Solaris Software-Progress" showsyou the progress of the installation in form of a progress bar. (The installationtakes up to 1 hour, depending of the speed of your machine and the amount ofyour disk.)Continue with ... h...16

16 Entering PasswordWait until the following message after reboot appears:

On this screen you can create a root password ...

b Enter root password.b Reenter root password for confirmation.

.

.

System identification is completed..

.

b login as rootb Choose CDE as default desktop, push [OK].b Open a terminal window. (Therefore click with the right mouse button in the work

space and select "Programs -> Terminal").b eject [ENTER].

Remove CD1.Continue with ... h...17

iFor the correct installation of the RC you must enter here the root password, even themessage suggest here to pass this step by pressing [ENTER]. If you do not enter herethe root password, the installation of the SUN Enterprise Manager will fail!

30 A50023-X4008-A1-2-7630



17 Use the Wizard Script

The description of the following steps are concerning to a specific constellationof the Radio Commander system. May be, that in your constellation not all of thequestions are asked. Follow the questions of the wizard script. For more infor-mation see in the Appendix the chapter about the "RC Configuration WizardScript".

+ ......RC Configura-tion WizardScript

b Insert the CD4.b /cdrom/cdrom0/install/wizard/cfgwiz.pl -m [ENTER]

You may get the following warning:

*** WARNING:wrong PROM (OBP) versions for board 0: is 3.23.0, should be 3.31.0*** WARNING:With a wrong PROM-Version the hardware detection may not work correctand SOFTWARE INSTALLATION MAY FAIL !You should update your PROM-Version first and restart the wizardDo you want to exit [y]:

Do you get this PROM warning? Y h...18N h...19

18 Update of PROM Necessary?b y [ENTER]

You have to update the PROM of your OMT with the version present on CD2within the subdirectory PROM. The patch depends from your machine:

Please update the PROM version according to the README files on the CD2.


!Insert the machines of your OMC-domain and the license-server in the apropriatenameservice files (e.g. /etc/hosts), otherwise the installation will fail.

E4x00 103346-22U1E 104288-07U1 (not E) 104881-07U5/U10 106121-16U60/E220R 106455-11U80/E420R 109082-05

iBe aware, if you have to upgrade the PROM version, make a copy ofium_configuration.cfg which is located on /tmp. The reason is, while you make theupgrade of the PROM version, you have to reboot your machine. With a reboot alwaysthe directory /tmp was cleared, so your previous generated ium_configuration.cfg file isdeleted.

A50023-X4008-A1-2-7630 31



19 Run the Wizard Script

scanning net parameters ...What type of RC-host is this machine (omp | omt | ned | tarantella | ext_backup)[omt]_

b Push [ENTER] for default value (in square brackets) or enter "omt" [ENTER].

Enter the name of the OMP [ ]_

b Enter here the hostname of the OMP and press [ENTER].

Enter the names of the additional OMTs, separated by "," []: _

b Enter here the hostname of all the OMTs, separated by "," ,, andthen press [ENTER].

Enter the names of the NEDs, separated by "," [ ]:_

b If available, enter here the hostname of all the NEDs, separated by "," andthen press [ENTER].

Enter the name of the external backup-server [ ]:_

b If available, enter here the hostname of the external backup-server ,(e.g.SBU) and then press [ENTER]. If you do not have a backup-server in yournetwork, press [ENTER] to accept the default empty value [ ].

scanning machines ...Enter the ipaddress for [ ]:_

b Enter the IP-address of the OMP you have entered before and press[ENTER].

Enter the ipaddress for [ ]:_

b Enter the IP-addresses of all the OMT(s) you have entered before andpress [ENTER].


b Enter the IP-address of the external backup-server you have enteredbefore and press [ENTER].

+++ NOTICE: Not more than one video card foundDoes the omp () have a HSI card [n]:

b Enter y [ENTER], if in your OMP a HSI card is available.

Does the omp () have a SPRITE card [n]:

32 A50023-X4008-A1-2-7630



b Enter y [ENTER], if in your OMP a SPRITE card is available.

Does the omp () have a AURORA card [n]:

b Enter y [ENTER], if in your OMP a AURORA card is available.

Does the omp () have a external disk [y]:

b Enter y [ENTER], if you have an external disk.Then you will get a summary of your entered data (example):

Configuration of RC-hosts:

IP-Address of omp5: 139.7.150.50IP-Address of OMT51: 139.7.150.51IP-Address of OMT52: 139.7.150.52IP-Address of OMT53: 139.7.150.53IP-Address of OMT54: 139.7.150.54IP-Address of OMT56: 139.7.150.56Default router for OMC:Domainname:NIS-type (none|NIS|NIS+): noneOMP has external disk: yLM-license file: /etc/opt/licenses/licenses_combinedLM-license server: omp5OMP has HSI card: yOMP has SPRITE card: yOMP has AURORA card: n

Do you want to change these values [y]:_

b n [ENTER]

Enter the backup-type on omp5 (internal|none) [none]: _b Enter here your backup type , (e.g. internal) [ENTER]

Enter the Jukebox device type on (dlt7000 | dlt8000 | 4mm_12GB)[4mm_12GB]:_

b Chose one of the following devices:Insert "4mm_12GB" [ENTER] if you have a DDS3 autoloader as Jukeboxdevicetype.Insert "dlt7000" [ENTER] if you have a L280 tape loader as Jukebox devicetype.Insert "dlt8000" [ENTER] if you have a L9 tape loader as Jukebox devicetype

Enter the Jukebox device on [/dev/rmt/1cbn]:_

b Please check that the value in square bracket must be equal to "/dev/rmt/1cbn"and press [ENTER].If another device is detected that means that your device hasn't been detected

A50023-X4008-A1-2-7630 33



in the right way.

Which license do you want to use for backup (permanent | demo) [demo]:_b [ENTER]

Enter the NSR-Resource [/nsr]:_

This question appears only if you have an external or internal backup-server.b [ENTER]

Install tool SMC [y]:_

b [ENTER]

Enter the hosts where tool tarantella should be installed, separated by "," [ ]:_

b [ENTER]

Enter the hosts where tool xbigx should be installed, separated by "," [ ]:_

This question appears only if more than one video card has been detected.b Press [ENTER] to accept the default empty value [ ] or enter the host name of

the host where tool xbigx should be installed, separatd by "," and press[ENTER].

Enter the XBigX license-key for [ ]:_

This question appears only if you have an OMT where you want to install xbigx.b Insert the license-key and press [ENTER].

Which manual should be installed (english|chinese|both|none) [both]:_b english [ENTER]

Then you will get a summary of your entered data (example):

Final Configuration:====================

IP-Address of omp5: 139.7.150.50IP-Address of OMT51: 139.7.150.51IP-Address of OMT52: 139.7.150.52IP-Address of OMT53: 139.7.150.53IP-Address of OMT54: 139.7.150.54IP-Address of OMT56: 139.7.150.56Backupserver type: internalJukebox device: /dev/rmt/1cbnJukebox devicetype: 4mm_12GBNSR-Resource: /nsrDefault router for OMC:

34 A50023-X4008-A1-2-7630



Domainname:NIS-type (none|NIS|NIS+): noneOMP has external disk: yLM-license file: /etc/opt/licenses/licenses_combinedLM-license server: omp5OMP has HSI card: yOMP has SPRITE card: yOMP has AURORA card: nInstall tarantella on:Install XBigX on:Manual to install: englishInstall SMC: y


b n [ENTER]

writing configuration file /tmp/ium_configuration.cfg


20 Prepare the RC Installation

Then execute the following commands:b cd / [ENTER]

!Check your generated ium_configuration.cfg (under /tmp). You can use the vi editor orthe cat command.

iBe aware, that the following command is very long and extends over two lines on thescreen! The system makes the line break by itself. Do not enter any carriage return inthe following command. Be sure that you have entered the complete command!

A50023-X4008-A1-2-7630 35



b /cdrom/cdrom0/install/install_toolset.sh -c /tmp/ium_configuration.cfg -p ../templates/ium_parse_ini.sh -i [ENTER]

.

.

Reboot is needed to continuePlease, reboot machine

And run /var/RC/install/install_toolset.sh [-s dir] -i#_

b init 6 [ENTER]The OMT boots. Login as root user when asked.

b root [ENTER]b Enter root-password.b Choose "Common Desktop Environment" (default).b Click with the mouse on [OK]-button.


21 3rd Party Tools InstallationOpen a terminal window (therefore click with the right mouse button in the workspace and select "Programs -> Terminal").

b /var/RC/install/install_toolset.sh -i [ENTER]

!Do not type anything at the keyboard, even you are asked! Installation will go on withdefault settings!

36 A50023-X4008-A1-2-7630



The CD4 will ejected automatically!Wait until:

.

.

need-cd: xcurrent_cd: 4 please insert cd nr. x press -key when ready_

b Remove CD4, insert CDx and close the CD tray.Wait until filemanager (started by vold) appears (this means, that the workstation has access to the CD-ROM).

b Click the filemanager away.b Type [ENTER] in the former opened terminal window to start reading the CD.

In the following you are always asked for the next CD in the same way asdepicted above. Follow the instructions of the installation routine.When you are asked to reboot the machine, please reboot the machine with thecommand "init 6", login as root again and run "install_toolset -i" like abovedescribed.Follow the instructions of the installation routine.At the end you will get the following information:

.

.

Installation of was successful.

Finish at Wed Oct 31 12:22:33 GMT2001You have mail in /var/mail/root#_

The OMT installation is now completed. Please eject and remove the last CD.


iIf you have installed SMC (Sun Management Center), please run

/opt/SUNWsymon/sbin/es-setup [ENTER]for a full configuration.

A50023-X4008-A1-2-7630 37



22 Activate the SWb init 6 [ENTER]

Login as root and activate the SW with following command:b /var/RC/install/omc_activate.sh -a [ENTER]

Then you have to reboot your OMT once again.b init 6 [ENTER]


23 Continue Installation Radio CommanderIs the OMP already installed? Y h...24

N h...PROC: Installa-tion of OMP

24 Additional OMTs?Are there further OMTs in your system to install? Y h...PROC: Installa-

tion of OMTN h...25

25 Check the Release Documentation

When the Radio Commander SW is installed completely, you have to continuewith the procedure ....

h...PROC: Acti-vate the RadioCommander

END

iThe logfile, to check if the installation was successful: /var/RC/install/install_toolset.sh.log.

iPlease check your actual Release Documentation. This documentation hints to correctanomalies of the present release.!

38 A50023-X4008-A1-2-7630



A50023-X4008-A1-2-7630 39


Installation Test Manual ITMNInstallation of OMP

2.3 Installation of OMP

Prior to installation, check that you have all required licenses for the SW to be installed(see PROC: Check Delivered SW and Licenses).With reference to the release documentation, check that you have all necessary CDs foryour installation.If there a NIS server is used, check whether the NIS client is installed (is a part of Solaris2.6 installation).Make sure that all physical devices (tape units, external disk devices, communicationunits, printers, ...) were powered on before starting with the installation procedure.Make sure that the Jumper (P601) must be installed on clock board.


an unrecoverable situation;

The following procedure describes the installation of an OMP with a console/terminalDEC VT100 (without a graphic card).

i You must be a superuser (root) for the OMP to perform all the steps in this procedure.


i To evaluate a value on the installation screen use the cursor buttons on the keyboard.To select the value use the [ENTER]-button or the space key.


i For the first time only and for Server 4500 only:Verify that the disk board has been inserted into slot 3 of the server; otherwise thepositions of the disk board and of the lower I/O board must be inverted: place the diskboard into slot 3 and the lower I/O board into slot 5.

40 A50023-X4008-A1-2-7630



1 Installation of Solaris CDb Disconnect the LAN cable and ignore every warning message about the "Link

Down - cable problem".If not yet happened, power on the Server with the key in "non-secure-position".Press the button for ejecting the CD tray and insert the CDROM labeled withCD1. Then close the CD tray.Enter break command [F5] (or [Stop] - A):

b [F5] BreakFrom the monitor prompt "{1} ok" enter the following command:

b boot cdrom [ENTER]

Resetting ...Software Power ON.

.

Rebooting with command: boot cdrom.

Configuring devices ....

.

Select a language

Please select "0" (English)b 0 [ENTER]

Select a Locale

Please choose "9" (USA-English (ISO-8859-1))b 9 [ENTER]

Then select the type of terminal used. Choose "3" for DEC VT100 or DECVT420. If a DEC VT420 is used you have to use [ESC][2] instead of [F2] in thewhole procedure.

b 3 [ENTER]


b [F2]_Continue or [ESC][2]



Host Name

b Please insert the hostname of this OMP (e.g. "omp99") in the editable text line.b [F2]_Continue or [ESC][2]

A50023-X4008-A1-2-7630 41




b Move the cursor to "yes" and select it with spacebar.b [F2]_Continue or [ESC][2]

If you have more than one network card you will be asked for the primarynetwork interface:


b Select your network interface (e.g. hme0), which is connected to the LAN.b [F2]_Continue or [ESC][2]

IP Address

b Enter the IP address of this OMP (e.g. "192.168.1.37").b [F2]_Continue or [ESC][2]

Confirm Information

This screen asks you to confirm last inputs. Press [F4] (or [ESC][4]) to correctyour inputs. If you are not aware about host name or IP address, refer to yoursystem administrator. If your entries are correct, continue with:


Name Service

If you want to use a NIS. h...2 If you do not want to use a NIS. h...3

42 A50023-X4008-A1-2-7630



2 Only for using NISb Select "NIS" for the installation -> please refer to your customer network infra-

structure or needs!b [F2]_Continue or [ESC][2]


b Enter your NIS/NIS+ domain name (e.g. "omc.ulm").b [F2]_Continue or [ESC][2]

Name Server

b Select "Find One".b [F2]_Continue or [ESC][2]

Confirm Information

At this point a summary screen asks you to confirm your last inputs. Press [F4](or [ESC][4]) to correct your inputs. If your entries are correct, continue with:

b [F2]_Continue or [ESC][2]Continue with ... h...4

3 If there is no NISb Select "[X] None" using the arrow keys and confirming with the spacebar.b [F2]_Continue or [ESC][2]

Confirm Information

At this point a summary screen asks you to confirm your last inputs. Press [F4](or [ESC][4]) to correct your inputs. If your entries are correct, continue with:

b [F2]_Continue or [ESC][2]Continue with ... h...4

4 Do you have a Subnet?

Subnets


N h...6

A50023-X4008-A1-2-7630 43



5 Only if you have a Subnetb If you have a subnet, select "[X] YES" using the arrow keys and confirming with

the spacebar.b [F2]_Continue or [ESC][2]

Netmask

b Enter the netmask of your OMP, e.g. "255.255.255.240".b [F2]_Continue or [ESC][2]


6 If you have no Subnetb If you do not have a subnet, select "[X] NO" using the arrow keys and

confirming with the spacebar.b [F2]_Continue or [ESC][2]


7 Enter Date and Time

Time Zone

b Select as time zone "[X] other - offset from GMT".b [F2]_Continue or [ESC][2]

Offset From GMTHours offset:

b 0 [F2]_Continue or [ESC][2]

Date and Time

b Correct your local date and time if necessary.b [F2]_Continue or [ESC][2]

Confirm Information

At this point a table summarizes the previous choices. If all of them are correctpress [F2] (or [ESC][2]) to continue, else press [F4] (or [ESC][4]) to changethem.

b [F2]_Continue or [ESC][2]The info window "System Identification is completed" appears. At this point thesystem identification is completed.

b Please reconnect the LAN cable.Continue with ... h...8

44 A50023-X4008-A1-2-7630



8 Solaris Interactive Installation


You have to choose "[F4]_Initial"b [F4]_Initial or [ESC][4]





Select Languages

Do not select any language. Continue the installation in English.b [F2]_Continue or [ESC][2]

Select Software

b Select "Entire Distribution for Radio Commander" moving the cursor with arrowkeys and select by pressing the space bar.


Select Disks

b Select all internal disks you have in the OMP. For this make a mark "X" in eachrow.

iDo not select the external disk devices. Select only the internal disks (c0t....).

A50023-X4008-A1-2-7630 45




Preserve Data



You have to take "Manual Layout".b [F4] or [ESC][4]

File Systems and Disk Layout

b Chose the root disk (first disk), using the arrow keys. This disk should preparedfor root-partition "/".

b [F4] or [ESC][4]Continue with ... h...9

9 Customize the File System and Disk Layout

Select Disk to customize

b Type [F4]-Customize (or [ESC][4] ).The following steps depend on your hard disk configuration of the OMP: If your hard disk size is 4GB or smaller h...10 If your hard disk size is bigger than 4GB h...11

10 Partitioning If Your Hard Disk Size is 4GB or Smaller


b Enter "swap" partition in slice 1 and set the size (MBs) to 1024, enter in slice 7 apartition for disksuite DB with size 3 MB (its name does not matter and may stayempty), enter root partition "/" in slice 0 and set the size to the maximum (=overlap - swap - 3; take the value from the line "free".).

iThe internal disks have different identification name, depending from the OMP archi-tecture:1. Server E420R: First: c0t0d0, Second: c0t1d0.2. Server E4500: First: c0t10d0, Second: c0t11d0.

Slice Mount Point Size (MB) 0 / 1 swap 1024 2 overlap 3

46 A50023-X4008-A1-2-7630





b Select 2nd disk (the marked disk line has a underlaying background).b Type [F4]-Customize (or [ESC][4] ).

Customize Disk: c0..1...d0

b Enter "swap" partition in slice 1 and set the Size (MBs) to 1024, enter "/export"in slize 7 and set the Size to the maximum (=overlap - swap; take the value fromthe line "free".).

4 5 6 7 3

Slice Mount Point Size (MB)

! Warning: Do not modify "overlap" -> The overlap concerns the whole disk! If you change here the entry, you may lost or corrupt your data!

Slice Mount Point Size (MB) 0 1 swap 1024 2 overlap 3 4 5 6 7 /export

!Warning: Do not modify "overlap" -> The overlap concerns the whole disk! If youchange here the entry, you may lost or corrupt your data!

A50023-X4008-A1-2-7630 47





If you find here something wrong, you can correct your input. If all of them arecorrect, press [F2] (or [ESC][2]) to continue, else press [F4] (or [ESC][4]) tochange them.



Here you can check your entries once again. If you are finished with customizingyour disks, [F2]_Continue or [ESC][2] .Continue with ... h...12

11 Partitioning If Hard Disk Size is Bigger Than 4GB


b Enter "swap" partition in slice 1 and set the size (MBs) to 2048, enter in slice 7 apartition for disksuite DB with size 3 MB (its name does not matter and may stayempty), enter root partition "/" in slice 0 and set the size to the maximum (=overlap - swap - 3; take the value from the line "free".).

Name Partition MB filesys1=rootdisk.s0 / filesys2=rootdisk.s1 swap 1024 filesys3=rootdisk.s7 3 filesys3=c0t1(1)d0.s1 swap 1024 filesys4=c0t1(1)d0.s7 /export

Slice Mount Point Size (MB) 0 / 1 swap 2048 2 overlap 3 4 5 6 7 3

! Warning: Do not modify "overlap" -> The overlap concerns the whole disk! If you change here the entry, you may lost or corrupt your data!

48 A50023-X4008-A1-2-7630





b Select 2nd disk (the marked disk line has a underlaying background).b Type [F4]-Customize (or [ESC][4] ).

Customize Disk: c0..1..d0

b Enter "swap" partition in slice 1 and set the Size (MBs) to 2048, enter "/export"in slize 7 and set the Size to the maximum (=overlap - swap; take the value fromthe line "free".).Slice Mount Point Size (MB)

0 1 swap 2048 2 overlap 3 4 5 6 7 /export

!Warning: Do not modify "overlap" -> The overlap concerns the whole disk! If youchange here the entry, you may lost or corrupt your data!

A50023-X4008-A1-2-7630 49





If you find here something wrong, you can correct your input. If all of them arecorrect, press [F2] (or [ESC][2]) to continue, else press [F4] (or [ESC][4]) tochange them.



Here you can check your entries once again. If you are finished with customizingyour disks, [F2]_Continue or [ESC][2] .Continue with ... h...12

Name Partition MB filesys1=rootdisk.s0 / filesys2=rootdisk.s1 swap 2048 filesys3=rootdisk.s7 3 filesys3=c0t1(1)d0s1 swap 2048 filesys4=c0t1(1)d0s7 /export

50 A50023-X4008-A1-2-7630



12 Installation of File Systemb [F2]_Continue or [ESC][2]


This screen deals with the remote file system mounting. For the OMP system itis needed to bypass this stage:


Profile

At this point a summary table shows all the entries selected so far. You are ableto change any of them (if needed) by means of arrows keys and space bar. If allentries are correct ...

b Confirm settings with [F2]_Continue or [ESC][2] .

Reboot After Installation?

b Select "[X] Auto Reboot" and [F2]_Continue or [ESC][2]

Solaris Initial Install

You will see the progress of the installation in %.Wait until the hard disks are formatted and the file system and all patch pack-ages are installed after an automatically reboot. This can take up to 1 or 2hours, depending on the capacity of your hard disks, the speed of your server,the speed of your CD-drive.Continue with ... h...13



b Enter root password .b Reenter root password for confirmation .

iFor the correct installation of the RC you must enter here the root password, even themessage suggest here to pass this step by pressing [ENTER]. If you do not enter herethe root password, the installation of the SUN Enterprise Manager will fail!

iOptional: Depending on the OMP type or PROM level you may get here the followingmessage:"By default autoshutdown is enabled..."Type [n]"...not be asked again..."Type [y]

A50023-X4008-A1-2-7630 51




14 Continue the Installation

System identification is completed.

.

console login: Nov 6 11:24:30 ....

Login as root user.b root [ENTER]b [ENTER]b Set up your name services for the workstation according to your network ad-

ministration: policyb Type eject [ENTER] and then remove CD1.


15 File Transfer From Earlier Installed OMTCreate the directory /etc/opt/licenses on the OMP. Therefore use the followingcommands on OMP:

b mkdir -p /etc/opt/licenses [ENTER]Copy the licenses_combined file from the OMT to your OMP via ftp:

b cd licenses [ENTER]b ftp [ENTER]b open [ENTER]b user name: root [ENTER]b password: [ENTER]b cd [ENTER]b mget licenses_combined [ENTER]b quit [ENTER]

Now you have finished the ftp.Check that the file "licenses_combined" on the OMP has the correct file name"licenses_combined" without any extension! If necessary, rename it.Continue with ... h...16

16 Use the Wizard Script

!Insert the machines of your OMC-domain and the license-server in the apropriatenameservice files (e.g. /etc/hosts), otherwise the installation will fail.

52 A50023-X4008-A1-2-7630



The description of the following steps are concerning to a specific constellationof the Radio Commander system. May be, that in your constellation not all of thequestions are asked. Follow the questions of the wizard script. For more infor-mation see in the Appendix the chapter about the "RC Configuration WizardScript".

+ ......RC Configura-tion WizardScript

b Insert the CD4.b /cdrom/cdrom0/install/wizard/cfgwiz.pl -m [ENTER]

You may get the following warning:

*** WARNING:wrong PROM (OBP) versions for board 0: is 3.23.0, should be 3.31.0*** WARNING:With a wrong PROM-Version the hardware detection may not work correctand SOFTWARE INSTALLATION MAY FAIL !You should update your PROM-Version first and restart the wizardDo you want to exit [y]:

Do you get this PROM warning? Y h...17N h...18

17 Update of PROM Necessary?b y [ENTER]

You have to update the PROM of your OMP with the version present on CD2within the subdirectory PROM. The patch depends from your machine:

Please update the PROM version according to the README files on the CD2.


E4x00 103346-22U1E 104288-07U1 (not E) 104881-07U5/U10 106121-16U60/E220R 106455-11U80/E420R 109082-05SunFire 111346-02Blade 100 111179-02

iNote, that on new SunFire 4800 (equipped with 900MHz CPUs) the recommendedfirmware version is 5.12.6. For the Sunfire a downgrade is not possible.

iBe aware, if you have to upgrade the PROM version, make a copy ofium_configuration.cfg which is located on /tmp. The reason is, while you make theupgrade of the PROM version, you have to reboot your machine. With a reboot alwaysthe directory /tmp was cleared, so your previous generated ium_configuration.cfg file isdeleted.

A50023-X4008-A1-2-7630 53



18 Run of the Wizard Script

scanning net parameters ...What type of RC-host is the machine (omp|omt|ned|tarantella|ext_backup)[omp]_

b Push [ENTER] for default value (in square brackets) or enter "omp" [ENTER].

Enter the names of the OMTs, separated by "," [ ]:_

b Enter here the hostname of all the OMTs, separated by "," ,, andthen press [ENTER].

Enter the names of the NEDs, separated by "," [ ]:_

b Enter here the hostname of all the NEDs, separated by "," and then press[ENTER].

Enter the names of the tarantella servers, separated by "," [ ]:_

b If you want to install Tarantella enter the hostname of the OMP and thenpress [ENTER].If you don't want to install Tarantella press [ENTER].

Enter the names of the tarantella application servers, separated by "," [ ]:_

b If you want to install Tarantella enter the hostname of the OMTs on which youwant to enable the opening of a RC session via Tarantella separeted by ","and then press [ENTER].If you don't want to install Tarantella press [ENTER].

Enter the name of the external backup-server [ ]:_

b Enter here the hostname of the external backup-server ,(e.g. SBU) andthen press [ENTER].If you do not have a backup-server in your network, press [ENTER] to acceptthe default empty value [ ].

Enter the default router for OMC [ ]:

b If you have a default router for OMC enter the TCP/IP address of it andpress [ENTER].

Enter the OMC region ID [0]:

b Enter the OMC region ID and press [ENTER].

scanning machines ...Enter the ipaddress for [ ]:_

b Enter the IP-address of all the OMT(s) you have entered before and press

54 A50023-X4008-A1-2-7630



[ENTER].


b Enter the IP-address of the external backup-server you have enteredbefore and press [ENTER].Now you may get some notifications (depending from your system), like:

+++ NOTICE: Not more than one video card found+++ NOTICE: 2 disk controllers found+++ NOTICE: HSI card found+++ NOTICE: No SPRITE card found+++ NOTICE: No AURORA card found

Then you will get a summary of your entered dataup to now:

Configuration of RC-hosts:IP-Address of : IP-Address of : OMC region ID: Default router for OMC: Domainname:NIS-type (none | NIS | NIS+): LM-license file: /etc/opt/licenses/licenses_combinedLM -licenses server:


b n [ENTER]

Enter the Jukebox device type on (dlt7000 | dlt8000 | 4mm_12GB)[4mm_12GB]:_

b Chose one of the following devices:Insert "4mm_12GB" [ENTER] if you have a DDS3 autoloader as Jukeboxdevicetype.Insert "dlt7000" [ENTER] if you have a L280 tape loader as Jukebox devicetype.Insert "dlt8000" [ENTER] if you have a L9 tape loader as Jukebox devicetype

Enter the Jukebox device on [/dev/rmt/1cbn]:_

b Please check that the value in square bracket must be equal to "/dev/rmt/1cbn"and press [ENTER].If another device is detected that means that your device hasn't been detectedin the right way.

Do you want to install the backup licenses [y]:

b Press [ENTER] to accept to insert all the backup licenses.When asked, you must insert all the enabler code for the backup products.

A50023-X4008-A1-2-7630 55



If you don't have the definitive licenses you can insert an empty value for theauthorization code. In this case don't forget to insert the authorization codeusing Solstice Backup GUI.

Enter the enabler code for Jukebox [ ]:_

b Insert the license-key and press [ENTER].

Enter the authorization code for Jukebox [ ]:_

b Insert the license-key and press [ENTER] or press [ENTER] to accept the emptyvalue.

Enter the enabler code for Solstice [ ]:_

b Insert the license-key and press [ENTER] .

Enter the authorization code for Solstice [ ]:_


Enter the enabler code for Informix [ ]:_


Enter the authorization code for Informix [ ]:_


Enter the enabler code for Oracle [ ]:_


Enter the authorization code for Oracle [ ]:_


Enter the NSR-Resource [/nsr]:_

b Push [ENTER] for default value (in square brackets).

Install tool SMC [y]:_

b Push [ENTER] for default value (in square brackets) or [n] [ENTER].

Install tool ANNEX [n]:_

b Push [ENTER] for default value (in square brackets) if you want to install theremote console or [n] [ENTER].

56 A50023-X4008-A1-2-7630



Enter the hosts where tool xbigx should be installed, separated by "," [ ]:_

b Press [ENTER] to accept the default empty value [ ] or enter the host name ofthe host where tool xbigx should be installed, separatd by "," and press[ENTER].

Enter the XBigX license-key for [ ]:_

This question appears only if you have an OMT on the OMP where you want toinstall xbigx.


Which manual should be installed (english|chinese|both|none) [both]:_b Insert the manual that shold be installed and press [ENTER].

Then you will get a summary of your entered data (example):

Final Configuration:IP-Address of : P-Address of : Backupserver type: Jukebox device: /dev/rmt/0cbnJukebox devicetype: NSR-Resource: /nsrEnabler code for Jukebox: Auth. code for Jukebox: Enabler code for Solstice: Auth. code for Solstice: Enabler code for Informix: Auth. code for Informix: Enabler code for Oracle: Auth. code for Oracle: Default router for OMC: Domainname:NIS-type (none | NIS | NIS+): LM-license file: /etc/opt/licenses/licenses_combinedLM-licenses server: Install tarantella on: Install licenses for backup: Install XBigX on:Manual to install: Install SMC:


b If you want to change the configuration, answer [y] [ENTER].Repeat the entries once again. For correct entries confirm your previous selec-tion (pressing [ENTER]). Then you will get all the information again, which hasbeen entered up to now.To accept the configuration, answer [n] [ENTER].

A50023-X4008-A1-2-7630 57



writing configuration file /tmp/ium_configuration.cfg#_


19 Installation Preparation

Change to the CDROM and launch the install script:b cd / [ENTER]

b /cdrom/cdrom0/install/install_toolset.sh -c /tmp/ium_configuration.cfg -p ../templates/ium_parse_ini.sh -i [ENTER]

The install script will perform: Installation of perl because perl scripts will be used in preparation. Preparation for RC, copy all necessary files for RC installation. Preparation for 3rd party, copy all necessary files for 3rd party installation. Check ium_configuration.cfg. Generate installation files for 3rd party installation. Perform pre installation, this makes some system changes (e.g. entries in

/etc/system for SEM), after this pre installation there is a reboot necessarybecause of the changes in /etc/system.

.

.

Please, reboot machine

And run /var/RC/install/install_toolset.sh [-s dir] -i

b init 6 [ENTER]The OMP boots. Login as root user when asked.

b root [ENTER]b Enter root-password [ENTER]


20 3rd Party Installationb /var/RC/install/install_toolset.sh -i [ENTER]

!Check your generated ium_configuration.cfg (under /tmp). You can use the vi editor orthe cat command.

iBe aware, that the following command is very long and extends over two lines on thescreen! The system makes the line break by itself. Do not enter any carriage return inthe following command. Be sure that you have entered the complete command!

!Do not type anything at the keyboard, even you are asked! Installation will go on withdefault settings!

58 A50023-X4008-A1-2-7630



The CD4 will ejected automatically!Wait until:

.

.

need-cd: xcurrent_cd: 4 please insert cd nr. x press -key when ready_

b Remove CD4, insert CDx and close the CD tray.When the blinking LED of the CD-ROM device goes out, then

b [ENTER]In the following you are always asked for the next CD in the same way asdepicted above. Follow the instructions of the installation routine.When you are asked to reboot the machine, please reboot the machine with thecommand "init 6" and login as root again. If you are asked after a reboot to startthe installation script again, please enter the command:"/var/RC/install/install_toolset.sh -i [ENTER]"

At the end you will get the following information:

.

.

Installation of was successful

Finish at Tue Nov 6 12:11:11 GMT 2001

The OMP SW installation is now completed. Eject the last CD from the OMP.b eject [ENTER]b Remove the last CD and close the CD tray.

Reboot the OMP once more.b init 6 [ENTER]


iThe Installation of CD6 take one until two hours (depending from your hard ware). All other CDs needs between 5 minutes up to 15 minutes for their installation.

iIf you have installed SMC (Sun Management Center), please run

/opt/SUNWsymon/sbin/es-setup [ENTER]for a full configuration.

A50023-X4008-A1-2-7630 59



21 Check the Release Documentation

When the Radio Commander SW is installed completely, you have to continuewith the SW activation.

h...PROC: Acti-vate the RadioCommander

END

iPlease check your Release Documentation for the current release. This documentationhints to correct anomalies of the present release.Please Do not log on OMT as RC user as long as the OMP installation is not finishedand the SW is not activated. Otherwise the RC user will not have their home directorymounted from the OMP.

60 A50023-X4008-A1-2-7630



A50023-X4008-A1-2-7630 61


Installation Test Manual ITMNActivate the Radio Commander

2.4 Activate the Radio Commander

This procedure describes the activation of the load for the OMP server and for theOMTs. This has to be done after the installation of the RC software.

The given values are examples.

1 Activate the Load on OMPb init 6 [ENTER]

Login as root and activate the SW with following command:b /var/RC/install/omc_activate.sh -a [ENTER]

With this command a link between /export/local/OMC/SW/OMT/01-01-47-00-21-00-02-03-15 and /export/local/OMC/SW/OMT/RUNNING has been createdand the ORACLE database has been configured.The activation of the OMP takes about one hour. Then you have to reboot yourOMP once again.

b init 6 [ENTER]


2 Activate the OMC Database on OMPb cd /export/local/OMC/SW/OMP/RUNNINGb ./activateConfigurationSet /export/local/OMC/SW/OMP/RUNNING/swl/CFGb init 6


i If the activation of a new SW load fails, no roll back to previous SW load version ispossible, but a new installation via CD is necessary. At OMP(OMT) SW load activation time via O&M command, a compatibility checkbetween new OMP(OMT) SW load and running OMT(OMP) SW load is performed andactivation fails if the OMP/OMT compatibility check fails. In this case, RC operator willbe allowed to activate new OMP and OMT SW loads via CD SW load installation.

iThe logfile, to check if the activation of the SW was successful: /var/RC/install/omc_activate.sh.log

62 A50023-X4008-A1-2-7630



3 Check the Start on OMPb tail -f /export/local/OMC/SFG/sfg_file/sfg_logfile_omp

If the message The RC system is up in this logfile appears, the application hasstarted successfully.As an alternative you can use the messages displayed on the console to checkthe OMP application start-up. At the moment the output during the start-up are: OMP: RC System is coming up ... OMP: Layer started - 0 OMP: Layer started - 1

OMP: Layer started - 9 OMP: The RC System is UP. OMP: Internal Alignment Procedure Started OMP: Internal Alignment Procedure Completed

From this point the RC system can really work. All the messages about the BSSalignment depends on the link status.Continue with ... h...4

4 Activate the Load on OMTIf you have not activated the SW while installation of the OMT, you must it acti-vate now. After you has logged in as root user, activate the load with thecommand:

b /var/RC/install/omc_activate.sh -aThis creates the directory /export/local/OMC/SW/OMT/RUNNING.Continue with ... h...5

A50023-X4008-A1-2-7630 63



5 Check the Start on OMTb tail -f /export/local/OMC/SFG/sfg_file/sfg_logfile_omt

If the message The RC system is up in this logfile appears, the application hasstarted successfully.As an alternative you can use the messages displayed on the console to checkthe OMT application start-up. For this you have to open a console window in theCDE. At the moment the output during the start-up are: OMT: RC System is coming up ... OMT: Layer started - 0 OMT: Layer started - 1

OMT: Layer started - 3 OMT: The RC System is UP.

Only after the message "RC System is up" is displayed a GUI or CLI sessioncan be started.At the end of the FIRST activation (after a SCRATCH installation), the OMP andthe OMTs listed inside the ium_configuration.cfg have been registered in RadioCommander (according to /var/RC/install/omcconf.txt) so that it is possible tostart the network editor in order to fully configure the OMC.

END

64 A50023-X4008-A1-2-7630



A50023-X4008-A1-2-7630 65


Installation Test Manual ITMNInstallation of NED

2.5 Installation of NED

This procedure is intended to provide informations on how to install the Solaris 2.6 oper-ating system and the offline NED SW on a Sun Workstation. (For further informationabout the OS installation, refer to Solaris 2.6 System Administrator's Manual).With reference to the release documentation, check that you have all necessary CDs foryour installation.If there a NIS server is used, check whether the NIS client is installed (is a part of Solaris2.6 installation).


an unrecoverable situation;

1 Installation of Solaris Operating SystemInsert the CDROM labeled with CD1. Enter break command or [F5] to get the"ok"-prompt:

b [STOP] Aand then enter at the "ok" prompt:

b boot cdrom [ENTER]While you are waiting you should get something like:

Boot device ...SunOS ...

... and a rotating slash. Then opens a window "Solaris Install Console" withe themessage in it:

The system is coming up. Please wait.

Continue with h...2

i You must be a superuser (root) to perform all the steps in this procedure.

i To evaluate a value on the installation screen use the cursor buttons on the keyboard.To select the value use the [ENTER]-button or the space key.



66 A50023-X4008-A1-2-7630



2 Select Language and LocaleA new window opens:

Select Language and Locale

b Please select "English" and "USA-English (ISO-8859-1) with the mouse.b Push [Continue]






Host Name

b Click with the mouse into the host name text field and enter the hostname of thisNED (e.g. "ned") using the keyboard.



b Set it to "yes".b Push [Continue]

Continue with h...3

3 Do you have several Network Interfaces?If you have only one network interface, continue with ... h...4If in your NED are several network interfaces, then the following window opens:


b Select your primary network interface (e.g. hme0)b Push [Continue]

Continue with h...4

A50023-X4008-A1-2-7630 67



4 Enter the IP Address of your NEDThe next window on the screen is displayed:

IP Address

b Click with the mouse into the IP address text field and enter the IP address ofthis NED (e.g. "192.168.1.37").


Confirm Information

b Push [Continue] or correct your inputs.The next window on the screen is displayed:

Name Service

Depending from your system configuration: If you want to use a NIS. h...5 If you do not want to use a NIS. h...6

5 Only for using NIS/NIS+b Select "NIS/NIS+" for the installation -> please refer to your customer network

infrastructure or needs!b Push [Continue]



b Enter your NIS/NIS+ domain name (e.g. "omc.ulm").b Push [Continue]


Name Server

b Select "Find One".b Push [Continue]


Confirm Information

b Push [Continue] or correct your inputs.Continue with ... h...7

68 A50023-X4008-A1-2-7630



6 If there is no NISb Select [X] None.b Push [Continue]


Confirm Information

b Push [Continue] or correct your inputs.Continue with ... h...7

7 Do you have a Subnet?The next window on the screen is displayed:

Part of a Subnet


N h...9

8 Only if you have a Subnetb If you have a subnet, select "yes".b Push [Continue]


Netmask

b Enter the netmask of your OMP, e.g. "255.255.255.240".Continue with ... h...10

9 If you have no Subnetb If you do not have a subnet, select "No".b Push [Continue]


A50023-X4008-A1-2-7630 69



10 Continue the OS-InstallationThe next window on the screen is displayed:

Time Zone

b Select as time zone "Offset From GMT".b Push [Set...]


Offset from GMT

b Move the button on the "0" position (default) if necessary.b Push [Continue]


Date and Time

b Correct your local date and time if necessary. Therefore move the cursorthrough the fields with the arrow keys and edit the values.


Confirm Information

b Push [Continue] or correct your inputs.In the window "Solaris Install Console" displays in the last line:

.

.

Begin script install_beginn execution completed.

A new window opens:



70 A50023-X4008-A1-2-7630



11 Solaris Interactive Installationb Push [Initial] (default)b Push [Continue]



b Push the [Continue] button.

Select Languages

Select your language (e.g. German).b Push [add]b Push [Continue]


Select Software

b Select the "Entire Distribution" with the toggle button.b Push [Continue]


12 Customize the File System and Disk LayoutThe next window on the screen is displayed:

Select Disks

The following steps depend on the disk capacity of your NED: If your hard disk size is less than 512 MB. h...13 If your hard disk size is greater than 515 MB. h...14

A50023-X4008-A1-2-7630 71



13 Partitioning If Your Hard Disk Size is Less Than 512 MBThe next window on the screen is displayed:

Preserve Data













Name Partition MB filesys1=rootdisk.s0 / free filesys2=rootdisk.s1 swap 256

72 A50023-X4008-A1-2-7630




A50023-X4008-A1-2-7630 73



14 Partitioning If Your Hard Disk Size is Greater Than 512 MBThe next window on the screen is displayed:

Preserve Data













Name Partition MBfilesys1=rootdisk.s0 / free filesys2=rootdisk.s1 swap 512

74 A50023-X4008-A1-2-7630




15 File System and Disk LayoutThe next window on the screen is displayed:


b Push [Continue]

Profile

b Confirm settings and push [Begin Installation].The next window on the screen is an information window without a title:

b Push [Auto Reboot]The next window on the screen "Installing Solaris Software-Progress" showsyou the progress of the installation in form of a progress bar. (The installationtakes up to 1 hour, depending of the speed of your machine and the amount ofyour disk.)Continue with ... h...16



iFor the correct installation of the NED you must enter here the root password, even themessage suggest here to pass this step by pressing [ENTER]. If you do not en

Documents

RC siemens britmn