RADWIN 5000 Release Notes - BTW SA Notes/old/RW5000... · MIB files for releases 3.4 supporting RADWIN 5000, ... (refer to the MIB Reference appendix in the ... RADWIN 5000 Release

RADWIN 5000 - Release 3.4

Release Note

14-Feb-13

Page 1 of 12

RADWIN 5000 - Release 3.4 GA

Release Note

1 General

RADWIN 5000 Release 3.4 is a General Availability (GA) release for RADWIN 5000 radios. Release 3.4 introduces

new features and products. For upgrade instructions, please refer to “Software Upgrade” in section 5.

RADWIN 5000 HPMP is a high capacity OFDM/MIMO Point-to-Multipoint solution that provides enhanced service

opportunities for carriers and ISPs, targeting last-mile enterprise connectivity. RADWIN 5000 HPMP also presents an

attractive wireless connectivity solution for government and enterprise networks looking to deploy broadband mission

critical applications.

RADWIN 5000 HPMP Highlights:

Up to 250Mbps net aggregate throughput per Base Station (HBS) sector

Unique mechanism guaranteeing SLA per subscriber

Variety of Subscriber Units (HSUs) – 50, 25, 20, 10 and 5 Mbps net aggregate

Subscriber Unit capacity upgrade from 5Mbps to 10Mbps and up to 25Mbps

Fully outdoor and Small Form Factor MIMO HSUs

OFDM MIMO 2x2 enables nLOS deployment

Low and constant latency

Long range – 40 km/25 miles

Multiband – 4.9 to 6.4GHz

Support license bands of 3.x and 2.x GHz

Supports Mobility, Nomadic and Fixed topologies

Coexists with RADWIN‟s Point-to-Point products

2 Release Components

Component Name Description

1. Firmware HBS/HSU: build 3.4_b3425

2. RADWIN Manager

Release 9.4.50, build 9455. RADWIN Manager includes:

Software Upgrade Packages applicable to all RADWIN 5000 (ver. 3.4 GA), RADWIN

2000 (ver. 2.8 GA) and WinLink 1000 (ver. 1.9.40 GA) radios

Software Upgrade Package applicable to all RADWIN 5000 radios

3. MIB Files MIB files for releases 3.4 supporting RADWIN 5000, RADWIN 2000 and WinLink 1000

products (refer to the MIB Reference appendix in the User Manual).

4. Link Budget Calculator

Build 8610. Supports RADWIN 5000, RADWIN 2000 and WinLink 1000 products.

LBC Capabilities:

Supports all bands

Supports all product families

Supports all channel bandwidths

Provides time-slot capacity per range

Provides sector aggregate capacity

Supports 64 time-slots

5. Installation CD

CD content:

RADWIN Manager installation

Quick Installation Guide

User manual: RADWIN 5000 (English-3.4), RADWIN 2000 (English-2.8, Russian-

2.4.50), WinLink 1000 (English-1.9.40, Russian-1.9, Spanish 1.9.30)

Link Budget Calculator (LBC) for RADWIN 5000, RADWIN 2000 and WinLink 1000

6. New products See following section.


Release Note

14-Feb-13

Page 2 of 12

3 New Products

3.1 RADWIN HBS 5025 Series RADWIN HBS-5025 Series Base Station radios, supporting up to 25Mbps net aggregate throughput and up to

16 HSUs.

All new products use hardware version 3.

Catalog Numbers

Description

1. RW-5025-0C50 RADWIN HBS 5025 Series, Base Station Radio Connectorized for external antenna (2x

N-type), supporting multi frequency bands at 5.x GHz, factory default 5.8 GHz FCC/IC


N-type), supporting multi frequency bands at 5.x GHz, factory default 5.4 GHz ETSI


N-type), supporting 5.8 GHz India WPC


N-type), supporting multi frequency bands at 5.x GHz, factory default 5.4 GHz Universal

3.2 RADWIN HSU 550 Series RADWIN HSU-550 Series Subscriber Unit radios, supporting up to 50Mbps net aggregate throughput.

All new products use hardware version 6.

Catalog Numbers

Description

1. RW-5550-9164 RADWIN 5000 HSU 550 Series Subscriber Unit Radio with integrated high gain antenna,

supporting 6.4 GHz Universal


supporting multi frequency bands at 3.x GHz, factory default 3.65 GHz FCC/IC


supporting 3.5 GHz ETSI

3.3 Capacity Upgrade Keys Small form factor Subscriber Units (HSUs), supporting software capacity upgrades from 5Mbps to 10Mbps and

up to 25Mbps.

Catalog Numbers

Description

1. RW-9961-0510 RADWIN 5000 HSU; License Capacity Key from 5Mbps to 10Mbps




Release Note

14-Feb-13

Page 3 of 12

4 Modified Products

4.1 RADWIN HBS 5025 Series

Catalog Numbers

Modification

1. RW-5025-0B50 Support 4.9, 5.3, 5.4 and 5.8 GHz FCC Frequency Bands

4.2 RADWIN HSU 525 Series

Catalog Numbers

Modification

1. RW-5525-0A50 Support 4.9, 5.3, 5.4 and 5.8 GHz FCC Frequency Bands

2. RW-5525-0C50 Support 4.9, 5.3, 5.4 and 5.8 GHz FCC Frequency Bands


Catalog Numbers

Modification




Catalog Numbers

Modification




Release Note

14-Feb-13

Page 4 of 12

4.5 Multi Bands Radios A License Key to enable supported bands can be obtained at http://www.radwin.com/updates/lk-radwin.htm

following customer‟s online Declaration of Compliance with local regulations. Use the License Key Generator

to check whether the HBS/HSU supports your required bands according to the HBS/HSU serial number.

Product Name

6.4

GH

z U

niv

ersa

l

6.0

GH

z U

niv

ersa

l

5.9

GH

z U

niv

ersa

l

5.8

GH

z M

II C

hin

a

5.8

GH

z F

CC

/IC

5.8

GH

z W

PC

In

dia

5.8

GH

z E

TS

I

5.4

GH

z IC

5.4

GH

z F

CC

5.4

GH

z E

TS

I

5.4

GH

z U

niv

ersa

l

5.3

GH

z F

CC

/IC

5.3

GH

z E

TS

I

5.3

GH

z U

niv

ersa

l

5.0

GH

z U

niv

ersa

l

4.9

GH

z F

CC

4.9

GH

z U

niv

ersa

l

3.x

GH

z F

CC

/IC

3.x

GH

z E

TS

I

3.x

GH

z U

niv

ersa

l

2.5

GH

z F

CC

/IC

HB

S 5

20

0 S

erie

s

RW-5200-0250 - * - - - - - - -

RW-5200-4258 - + + - + * - + + - + + - + - + + - - - -

RW-5200-2250 - + + - + - - - * + - + - + + - - - -

RW-5200-9254 - - - - - * - - - - - -

RW-5200-9264 * - - - - - - - - - - - - - - - - - - - -

HB

S 5

10

0 S

. RW-5100-0230 - - - - - - - - - - - - - - - - - - -

RW-5100-2230 - - - - - - - - - - - - - - - - - - + -

RW-5100-8225 - - - - - - - - - - - - - - - - - - - -

HB

S 5

05

0 S

erie

s

RW-5050-0250 - * - - - - - - -

RW-5050-0150 - * - - - - - - -

RW-5050-4258 - + + - + * - + + - + + - + - + + - - - -

RW-5050-4158 - + + - + * - + + - + + - + - + + - - - -

RW-5050-2250 - + + - + - - - * + - + - + + - - - -

RW-5050-2150 - + + - + - - - * + - + - + + - - - -

RW-5050-9254 - - - - - * - - - - - -

RW-5050-9154 - - - - - * - - - - - -

HB

S 5

02

5 S

er.

RW-5025-0B50 - - * - - - - - - - - -

RW-5025-2B50 - - + - - - - - * + - + - - + - - - -

RW-5025-4B58 - - + + + * - - - - + - - + - - + - - - -

RW-5025-9B54 - - - - - - * - - - - - - - -

RW-5025-0C50 - - * - - - - - - - - -

RW-5025-2C50 - - + - - - - - * + - + - - + - - - -

RW-5025-4C58 - - + + + * - - - - + - - + - - + - - - -

RW-5025-9C54 - - - - - - * - - - - - - - -

http://www.radwin.com/updates/lk-radwin.htm


Release Note

14-Feb-13

Page 5 of 12

HB

S 5

800 S

. RW-5800-0250 - * - - - - - - -

RW-5800-4258 - + + - + * - + + - + + - + - + + - - - -

RW-5800-9254 - - - - - * - - - - - -

HS

U 5

50

Ser

ies

RW-5550-0250 - * - - - - - - -

RW-5550-0150 - * - - - - - - -

RW-5550-4258 - + + - + * - + + - + + - + - + + - - - -

RW-5550-4158 - + + - + * - + + - + + - + - + + - - - -

RW-5550-2250 - + + - + - - - * + - + - + + - - - -

RW-5550-2150 - + + - + - - - * + - + - + + - - - -

RW-5550-9154 - - - - - * - - - - - -

RW-5550-9264 * - - - - - - - - - - - - - - - - - - - -

RW-5550-9164 * - - - - - - - - - - - - - - - - - - - -

RW-5550-0130 - - - - - - - - - - - - - - - - - - -

RW-5550-2130 - - - - - - - - - - - - - - - - - - + -

HS

U 5

25

Ser

ies

RW-5525-0A50 - - * - - - - - - - - - - - -

RW-5525-0C50 - - * - - - - - - - - - - - -

RW-5525-2A50 - - + - - - - - * + - + - - + - - - -

RW-5525-2C50 - - + - - - - - * + - + - - + - - - -

RW-5525-4A58 - - + + + * - - - - + - - + - - + - - - -

RW-5525-4C58 - - + + + * - - - - + - - + - - + - - - -

RW-5525-9A54 - - - - - - * - - - - - - - -

RW-5525-9C54 - - - - - - * - - - - - - - -

RW-5525-0A50 - - * - - - - - - - - - - - -

HS

U 5

20

Ser

ies

RW-5520-0350 - * - - - - - - -

RW-5520-0150 - * - - - - - - -

RW-5520-4358 - + + - + * - + + - + + - + - + + - - - -

RW-5520-4158 - + + - + * - + + - + + - + - + + - - - -

RW-5520-2350 - + + - + - - - * + - + - + + - - - -

RW-5520-2150 - + + - + - - - * + - + - + + - - - -

RW-5520-9154 - - - - - * - - - - - -

RW-5550-9154 - - - - - * - - - - - -

RW-5520-0230 - - - - - - - - - - - - - - - - - - -

RW-5520-0130 - - - - - - - - - - - - - - - - - - -

RW-5520-2230 - - - - - - - - - - - - - - - - - - + -

RW-5520-2130 - - - - - - - - - - - - - - - - - - + -

RW-5520-8225 - - - - - - - - - - - - - - - - - - - -

RW-5520-9164 * - - - - - - - - - - - - - - - - - - - -

RW-5520-9264 * - - - - - - - - - - - - - - - - - - - -

HS

U

51

0

Ser

ies RW-5510-0350 - * - - - - - - -

RW-5510-4358 - + + - + * - + + - + + - + - + + - - - -


Release Note

14-Feb-13

Page 6 of 12

Legend:

Enabled band * Factory default band

+ Band supported and disabled - Band not supported

RW-5510-2350 - + + - + - - - * + - + - + + - - - -

RW-5510-9354 - - - - - * - - - - - -

RW-5510-0230 - - - - - - - - - - - - - - - - - - -

RW-5510-0130 - - - - - - - - - - - - - - - - - - -

RW-5510-2230 - - - - - - - - - - - - - - - - - - + -

RW-5510-2130 - - - - - - - - - - - - - - - - - - + -

RW-5510-9164 * - - - - - - - - - - - - - - - - - - - -

RW-5510-9264 * - - - - - - - - - - - - - - - - - - - -

RW-5510-0A50 - - * - - - - - - - - - - - -

RW-5510-0C50 - - * - - - - - - - - - - - -

RW-5510-2A50 - - + - - - - - * + - + - - + - - - -

RW-5510-2C50 - - + - - - - - * + - + - - + - - - -

RW-5510-4A58 - - + + + * - - - - + - - + - - + - - - -

RW-5510-4C58 - - + + + * - - - - + - - + - - + - - - -

RW-5510-9A54 - - - - - - * - - - - - - - -

RW-5510-9C54 - - - - - - * - - - - - - - -

HS

U 5

05

Ser

ies

RW-5505-0A50 - - * - - - - - - - - - - - -

RW-5505-0C50 - - * - - - - - - - - - - - -

RW-5505-2A50 - - + - - - - - * + - + - - + - - - -

RW-5505-2C50 - - + - - - - - * + - + - - + - - - -

RW-5505-4A58 - - + + + * - - - - + - - + - - + - - - -

RW-5505-4C58 - - + + + * - - - - + - - + - - + - - - -

RW-5505-9A54 - - - - - - * - - - - - - - -

RW-5505-9C54 - - - - - - * - - - - - - - -

HS

U 6

10

S.

RW-5610-0A50 - - * - - - - - - - - - - - - -

RW-5610-2A50 - - + - - - - - * + - + - - - - - - -

RW-5610-4A58 - - + + + * - - - - + - - + - - - - - - -

RW-5610-9A54 - - - - - - * - - - - - - - - -

HM

U

RW-5700-0250 - * - - - - - - -

RW-5700-4258 - + + - + * - + + - + + - + - + + - - - -

RW-5700-9254 - - - - - * - - - - - -


Release Note

14-Feb-13

Page 7 of 12

5 New Features

Feature Description

1. HSU Capacity Upgrade

Small form factor Subscriber Units (HSUs) now offer software capacity

upgrades from 5Mbps to 10 Mbps and up to 25 Mbps

Capacity Upgrade is valid for all bands, regulations and configurations

Capacity upgrade can be performed for each HSU individually or for the

entire sector via the HBS

Following PO, Software upgrade keys can be obtained from:

http://www.radwin.com/updates/LicenseKey/lk-radwin.htm

Supported by installed base through software upgrade to release 3.4 GA

2. FIPS-197

FIPS-197 is a U.S. government computer security standard that specifies

approved cryptographic algorithm to protect electronic data

Compliance with the Federal FIPS-197 standard, enabling secured

information transfer when utilizing RADWIN 5000 products in federal

agency deployments

RADWIN NIST Validation number: 2270

Validation publication:

http://csrc.nist.gov/groups/STM/cavp/documents/aes/aesval.html

Certified products:

1. Small-form-factor HSU-505/510/525

2. HBS-5025 Series

3. Provider Tagging Enhancement

Ability to configure VLAN provider TPID (Tag Protocol Identifier) per each

HSU in the Sector

Enable interoperability with legacy switches (e.g. Cisco) that supports TPID

of 0x8100 only

Configurable TPID values:

1. 0x9100 (default)

2. 0x8100

3. 0x88A8

Supported by installed base through software upgrade to release 3.4 GA

4. RADWIN Manager Frequency Band

Display

RADWIN Manager displays the occupied bandwidth per Channel bandwidth

and Frequency Band instead of the previous display that was based on Center

Frequency

6 Compatibility Component

Name Description

1. Software

Upgrade

Software upgrade can be applied to any previous RADWIN 5000 releases.

RADWIN 5000 Release 3.4 GA is not compatible with RADWIN 5000 prior to release 3.3 GA,

due to a new Air interface protocol. This means that HSUs that running release older than 3.3,

cannot synchronize to HBS that running release 3.4 and vice versa. Software Upgrade to release

3.4 is required for the HBS and all the HSUs in the sector.

In respect of a software upgrade for a sector operating in the 5.4 FCC band and for which the

operating channel is within the frequency range 5600 - 5650 MHz: The software upgrade will

enable ACS for all the available channels.

In respect of a software upgrade for a sector operating in 4.9 Universal band and for which the

operating channel is within the frequency range of 4990 - 5000 MHz: The software upgrade will

enable ACS for all the available channels (for further details, refer to line 2 in the Limitation

section below).

2. Software

Downgrade Software downgrade from release 3.4 GA to release 3.2.75 LA is not available, thus RADWIN

5000 units with release version prior to 3.3 should be upgraded to 3.4 GA for compatibility.






Release Note

14-Feb-13

Page 8 of 12

Component Name

Description

3. Firmware

RADWIN 5000 Radios are not compatible with WinLink 1000 or RADWIN 2000 Radios.

The new features listed above require release 3.4 on both the HBS and its HSUs.

Additional restrictions are listed below:

Older than Release 3.3 Release 3.3 and above

Release

3.4

Software upgrade is required to release

3.4, due to a new Air interface protocol

Fully compatible, Software upgrade is

recommended to release 3.4 to support the new

features in this release

4. RADWIN

Manager

1. Support all RADWIN products.

2. Overrides older RADWIN Manager installations, 8.5.30 and below.

3. Uses .NET 4.0 (included in the package, first installation might take several minutes).

4. Supported OS: Windows XP SP2 and higher, Windows Vista 32/64, Windows Server 2003 32, Win7

32/64bits, Windows Server 2008 32/64bits, Win8.

6. Manager “Help” feature is available for RADWIN 5000.

(*) For RNMS support, please contact RADWIN support.


Release Note

14-Feb-13

Page 9 of 12

7 Resolved Issues Issue Name Description Resolution

1. HBS-5025 Sync-Loss

In rare cases, HBS-5025 Sector that contains

mixed of HSUs from HW Rev. 2 and Rev. 6

and the HSUs are installed in a very close

proximately, and the mutual interference level

between the HSUs is above -30dBm, HSU

from Rev. 6 might suffer from continues sync

loss after link establishment

Resolved

2. Mobility RSS Threshold

Occasionally, RSS Threshold for synchronize

is not accurate and HMU unit might

synchronize with HBS that its RSS level is

lower than the RSS threshold by 15dB

Resolved

3. RNMS - Click on unit‟s

icon doesn‟t open

RADWIN Manager

In RNMS, RADWN Manager doesn‟t open

when the user clicks on the unit‟s icon Resolved

8 Known Issues from previous releases

8.1 HBS/HSU Issues

Issue Name Description Workaround

1. Missing SNMP Traps

Some SNMP traps might be missing after

HBS reset :

- HBS ready

- Management port status changed to

disconnected

Not service affected

2. Channel BW change

problem

Channel bandwidth switch from 10 to 20 MHz

on edge channels (Center frequency that is not

available on 20MHz) fails without

notification, and the sector continues to work

on 10MHz

Change frequency to a none edge channel

and change the channel bandwidth to

20MHz

3. HSU Device Reset

Occasionally, HSU reset may occur under full

capacity traffic at steady state under

20/40MHz channel BW

HSU Link recovers automatically after reset

4. Multiple HSMs

If a HBS is set as HSC-CT and detects

Multiple HSS sources with different Tx ratios,

its own Tx ratio changes continuously (trap is

send every second)

Remove redundant HSMs

5. Min Tx Power

In FCC/ETSI frequency bands the Minimum

Tx power can be set to a value of -11dBm

whereas the minimum should be -8dBm.

Set Minimum Tx power to -8dBm

6. Traffic Block Traffic does not pass from HSU to HSU

where a HBS LAN cable is disconnected

Reconnect HBS LAN cable and traffic

resumes

7. QoS

Best Effort priority queue throughput is

occasionally smaller by 10% than the

configured weight

8. LAN Port 100HD

Occasionally, when the HSU LAN port is

configured to auto-negotiate mode and it is

operating with equipment configured to

100FD, traffic might not be transferred under

100HD.

Change the mode of the equipment

connected to the HSU to auto-negotiate

mode and reset HSU device

9. HBS/HSU sync loss In rare cases, HBS/HSU sync loss may occur

under high interference and traffic load Link recovers automatically after sync loss

10. HBS sync time In rare cases, HBS sync time might be longer

than expected and can reach up to 20 seconds


Release Note

14-Feb-13

Page 10 of 12


11. HBS Ethernet Service

In rare cases, After multiple Sector sync loss

the Ethernet service may not be available

although Ethernet service display is active in

the RADWIN Manager

Perform HBS device reset

12. HBS/HSU Sync-Loss

Sync loss may occur once decreasing

HBS/HSU Tx power by 10dBm or more at

once

Link recovers after sync loss

automatically

Decreasing Tx power gradually

13. HBS/HSU BIT Failure

In a very rare cases, HBS/HSU might enter

into "BIT failed" state after device reset, while

no actual BIT error

Perform HBS/HSU device reset

14. Wrong SNMP Trap

Description

In rare cases , once disconnecting HSS pulse

cable from HSC site, the SNMP Trap reason

is "Improper Sync pulse" instead "Sync pulse

disappeared"

Ignore wrong trap description

15. Wrong RSS Display

Wrong RSS displayed on Link in Diversity

Antenna mode, when one of antenna ports is

physically disconnected

Ignore wrong RSS values and connect

antenna port


Release Note

14-Feb-13

Page 11 of 12

8.2 RADWIN Manager Issues


1. RADWIN Manager

termination

In rare cases, RADWIN Manager may

terminate under LAN cable disconnection and

reconnection

Restart the RADWIN Manager

2. Min/Max Window

size Display problem

In rare cases, when the window size is

minimized or maximized, there might be a

display problem.


3. Display issues

Various issues affect the display of the

RADWIN Manager but do not affect the

system functionality

In most cases the workaround is to “refresh

the display”, or close and reopen the

RADWIN Manager

4. Over-the-Air

connection

In rare cases, RADWIN Manager may lose

over-the-air connection to remote HSU after

sync-loss

Log off and log on to RADWIN Manager

5. HSU MIR

configuration

HSU MIR has illegal values (<0.5) after

Deregistration-Registration. It should be

unlimited by default

Reconfigure MIR value

6. Map display issues


RADWIN Manager Map View, however do

not affect the system functionality

In most cases the workaround is to “refresh

the display”, or close and reopen the

RADWIN Manager

7. RADWIN Manager

loading time

In rare cases, RADWIN Manager loading

time could be up to 15 seconds

Ignore and wait for the login screen to

appear

8. High memory usage

High PC memory usage may occur when

RADWIN Manager is connected to HBS and

the HBS has many Resets/Sync loss events

Log off and log on to the RADWIN

Manager

9. Unregistered HSU

configuration

In rare cases, there is a problem configuring

some parameters on unregistered HSU (HSU

is synchronized but not registered)

Register the HSU and re-configure

10. Display problem after

Software Downgrade


RADWIN Manager after performing Software

downgrade to release 3.2.75, however does

not affect the system functionality

Log off and log on to RADWIN Manager

11. Remove 9.4.10

installation

Uninstalling the 9.4.10 RADWIN Manager

fails

Remove 9.4.10 installation using Windows

add/remove program and install the required

manager

12. Task bar icon Task bar icon doesn't reflect Link status in

Windows 7

Select option "Never combine" or

"Combine when taskbar full" in Windows 7

Taskbar and Start Menu Properties

13. Add time slots to

Mobility/Nomadic

HSU/HMU

In the mobility or nomadic service, it is not

possible to add Time slots to a specific service

level where the user initially set the number of

HSUs to the level (using “Add”)

Open any HSU (not necessarily active) at

the required level. Using Update Service,

change its number of time slots. The change

will apply to all HSUs at that level.

Limitation: There must be sufficient free

time slots.

14. HSU Link Status

Occasionally, after multiple HSU sync-losses,

HSU Link-Status might not be displayed in

the Manager, while connecting to the HSU

directly and not via the HBS. Service and link

is still up and running,

Ignore or reset HSU


Release Note

14-Feb-13

Page 12 of 12


15. HSU-610 POE Port

Information

Occasionally, when no external device is

connected to the PoE-Out port on HSU-5610

the RADWIN Manager might display

irrelevant power Consumption/Voltage values

(e.g. 2V / 960mA)

Ignore values

16. HBS Restore

In rare cases, HBS configuration restore might

fails on 'HSU connection Table, and HBS

enter into Inactive state instead of active

Activate HBS via the Manager

17. HBS Restore

Occasionally, HBS configuration restore

might fails to restore mobility settings and the

message at Restore window "Failed to restore

mobility settings “appears

Re-allocate new level/TS of missing

configuration.

18. Active Alarms

Impossible to view/save Active Alarms of

ODU in BIT Failed state, after changing from

MAP to Card/Grid view

Re-login to the RADWIN Manager

19. Wrong Remaining

Time-Slots

When the user enter the number of time slots

via the keyboard (instead of using the

up/down arrows) for the Mobility/Nomadic

HSUs, the calculation of the remaining Time

slots is wrong

Change TS configuration via the RADWIN

Manager Up/Down arrows

20. Backup File Name

Backup file name is different between

RADWIN Manager 9.4.30 and former

releases and file is not overwritten

Change file name manually or select the

right backup file

21. IfInOctets MIB

counter

The counter „IfInOctets‟ in RFC 1213 does

not increment for the HSU

Problem exists since release 3.3.0. Counter

work properly at downgrade version 3.2.70.

22. HBS-25 - Wrong HSS

Trap

After HBS-25 reboot it sends a wrong SNMP

Trap that related to HSS Ignore this trap

9 Known Issues from current release

9.1 RADWIN Manager Issues


1. RADWIN Manager

termination

In rare cases, after software upgrade is

completed and reset is done, a Microsoft

.NET framework error will appear and

RADWIN Manager will be terminated


Documents

RADWIN 5000 Release Notes - BTW SA Notes/old/RW5000... · MIB files for releases 3.4 supporting RADWIN 5000, ... (refer to the MIB Reference appendix in the ... RADWIN 5000 Release