Rackmount en 10

7/31/2019 Rackmount en 10

1/192


2/192


3/192

Manual Code C120-H016-10ENPart No. 820-0686-17June 2009, Revision A

SPARC EnterpriseEquipment Rack Mounting Guide

Fujitsu 19-inch Rack


4/192

PleaseRecycle

Copyright 2007-2009 FUJITSU LIMITED, 1-1, Kamikodanaka 4-chome, Nakahara-ku, Kawasaki-shi, Kanagawa-ken 211-8588, Japan. All rights reserved.

Sun Microsystems, Inc. provided technical input and review on portions of this material.

Sun Microsystems, Inc. and Fujitsu Limited each own or control intellectual property rights relating to products and technology described in this document,and such products, technology and this document are protected by copyright laws, patents and other intellectual property laws and international treaties. The

intellectual property rights of Sun Microsystems, Inc. and Fujitsu Limited in such products, technology and this document include, without limitation, one ormore of the United States patents listed at http://www.sun.com/patents and one or more additional patents or patent applications in the United States or othercountries.

This document and the product and technology to which it pertains are distributed under licenses restricting their use, copying, distribution, and decompilation.No part of such product or technology, or of this document, may be reproduced in any form by any means without prior written authorization of Fujitsu Limitedand Sun Microsystems, Inc., and their applicable licensors, if any. The furnishing of this document to you does not give you any rights or licenses, express orimplied, with respect to the product or technology to which it pertains, and this document does not contain or represent any commitment of any kind on the partof Fujitsu Limited or Sun Microsystems, Inc., or any affiliate of either of them.

This document and the product and technology described in this document may incorporate third-party intellectual property copyrighted by and/or licensedfrom suppliers to Fujitsu Limited and/or Sun Microsystems, Inc., including software and font technology.

Per the terms of the GPL or LGPL, a copy of the source code governed by the GPL or LGPL, as applicable, is available upon request by the End User. Please

contact Fujitsu Limited or Sun Microsystems, IncThis distribution may include materials developed by third parties.

Parts of the product may be derived from Berkeley BSD systems, licensed from the University of California. UNIX is a registered trademark in the U.S. andin other countries, exclusively licensed through X/Open Company, Ltd.

Sun, Sun Microsystems, the Sun logo, Java, Netra, Solaris, Sun Ray, Answerbook2, docs.sun.com, OpenBoot, and Sun Fire are trademarks or registeredtrademarks of Sun Microsystems, Inc., or its subsidiaries, in the U.S. and other countries.

Fujitsu and the Fujitsu logo are registered trademarks of Fujitsu Limited.

All SPARC trademarks are used under license and are registered trademarks of SPARC International, Inc. in the U.S. and other countries. Products bearingSPARC trademarks are based upon architecture developed by Sun Microsystems, Inc.

SPARC64 is a trademark of SPARC International, Inc., used under license by Fujitsu Microelectronics, Inc. and Fujitsu Limited.The OPEN LOOK and Sun Graphical User Interface was developed by Sun Microsystems, Inc. for its users and licensees. Sun acknowledges the pioneeringefforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry. Sun holds a non-exclusive licensefrom Xerox to the Xerox Graphical User Interface, which license also covers Suns licensees who implement OPEN LOOK GUIs and otherwise comply withSuns written license agreements.

United States Government Rights - Commercial use. U.S. Government users are subject to the standard government user license agreements of SunMicrosystems, Inc. and Fujitsu Limited and the applicable provisions of the FAR and its supplements.

Disclaimer: The only warranties granted by Fujitsu Limited, Sun Microsystems, Inc. or any affiliate of either of them in connection with this document orany product or technology described herein are those expressly set forth in the license agreement pursuant to which the product or technology is provided.EXCEPT AS EXPRESSLY SET FORTH IN SUCH AGREEMENT, FUJITSU LIMITED, SUN MICROSYSTEMS, INC. AND THEIR AFFILIATES MAKE

NO REPRESENTATIONS OR WARRANTIES OF ANY KIND (EXPRESS OR IMPLIED) REGARDING SUCH PRODUCT OR TECHNOLOGY ORTHIS DOCUMENT, WHICH ARE ALL PROVIDED AS IS, AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS ANDWARRANTIES, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULARPURPOSE OR NON-INFRINGEMENT, ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLYINVALID. Unless otherwise expressly set forth in such agreement, to the extent allowed by applicable law, in no event shall Fujitsu Limited, SunMicrosystems, Inc. or any of their affiliates have any liability to any third party under any legal theory for any loss of revenues or profits, loss of use or data,or business interruptions, or for any indirect, special, incidental or consequential damages, even if advised of the possibility of such damages.

DOCUMENTATION IS PROVIDED AS IS AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES,INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT, AREDISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID.


5/192

Copyright 2007-2009 FUJITSU LIMITED, 1-1, Kamikodanaka 4-chome, Nakahara-ku, Kawasaki-shi, Kanagawa-ken 211-8588, Japon. Tous droits rservs.

Entre et revue tecnical fournies par Sun Microsystems, Incl sur des parties de ce matriel.

Sun Microsystems, Inc. et Fujitsu Limited dtiennent et contrlent toutes deux des droits de proprit intellectuelle relatifs aux produits et technologies dcritsdans ce document. De mme, ces produits, technologies et ce document sont protgs par des lois sur le copyright, des brevets, dautres lois sur la proprit

intellectuelle et des traits internationaux. Les droits de proprit intellectuelle de Sun Microsystems, Inc. et Fujitsu Limited concernant ces produits, cestechnologies et ce document comprennent, sans que cette liste soit exhaustive, un ou plusieurs des brevets dposs aux tats-Unis et indiqus ladressehttp://www.sun.com/patents de mme quun ou plusieurs brevets ou applications brevetes supplmentaires aux tats-Unis et dans dautres pays.

Ce document, le produit et les technologies affrents sont exclusivement distribus avec des licences qui en restreignent lutilisation, la copie, la distributionet la dcompilation. Aucune partie de ce produit, de ces technologies ou de ce document ne peut tre reproduite sous quelque forme que ce soit, par quelquemoyen que ce soit, sans lautorisation crite pralable de Fujitsu Limited et de Sun Microsystems, Inc., et de leurs ventuels bailleurs de licence. Ce document,

bien quil vous ait t fourni, ne vous confre aucun droit et aucune licence, expresses ou tacites, concernant le produit ou la technologie auxquels il serapporte. Par ailleurs, il ne contient ni ne reprsente aucun engagement, de quelque type que ce soit, de la part de Fujitsu Limited ou de Sun Microsystems,Inc., ou des socits affilies.

Ce document, et le produit et les technologies quil dcrit, peuvent inclure des droits de proprit intellectuelle de parties tierces protgs par copyright et/oucds sous licence par des fournisseurs Fujitsu Limited et/ou Sun Microsystems, Inc., y compris des logiciels et des technologies relatives aux polices decaractres.Par limites du GPL ou du LGPL, une copie du code source rgi par le GPL ou LGPL, comme applicable, est sur demande vers la fin utilsateur disponible;veuillez contacter Fujitsu Limted ou Sun Microsystems, Inc.

Cette distribution peut comprendre des composants dvelopps par des tierces parties.

Des parties de ce produit pourront tre drives des systmes Berkeley BSD licencis par lUniversit de Californie. UNIX est une marque dpose aux Etats-Unis et dans dautres pays et licencie exclusivement par X/Open Company, Ltd.

Sun, Sun Microsystems, le logo Sun, Java, Netra, Solaris, Sun Ray, Answerbook2, docs.sun.com, OpenBoot, et Sun Fire sont des marques de fabrique oudes marques dposes de Sun Microsystems, Inc., ou ses filiales, aux Etats-Unis et dans dautres pays.

Fujitsu et le logo Fujitsu sont des marques dposes de Fujitsu Limited.

Toutes les marques SPARC sont utilises sous licence et sont des marques de fabrique ou des marques dposes de SPARC International, Inc. aux Etats-Uniset dans dautres pays. Les produits portant les marques SPARC sont bass sur une architecture dveloppe par Sun Microsystems, Inc.

SPARC64 est une marques dpose de SPARC International, Inc., utilise sous le permis par Fujitsu Microelectronics, Inc. et Fujitsu Limited.

Linterface dutilisation graphique OPEN LOOK et Sun a t dveloppe par Sun Microsystems, Inc. pour ses utilisateurs et licencis. Sun reconnat lesefforts de pionniers de Xerox pour la recherche et le dveloppement du concept des interfaces dutilisation visuelle ou graphique pour lindustrie delinformatique. Sun dtient une license non exclusive de Xerox sur linterface dutilisation graphique Xerox, cette licence couvrant galement les licencisde Sun qui mettent en place linterface dutilisation graphique OPEN LOOK et qui, en outre, se conforment aux licences crites de Sun.

Droits du gouvernement amricain - logiciel commercial. Les utilisateurs du gouvernement amricain sont soumis aux contrats de licence standard de SunMicrosystems, Inc. et de Fujitsu Limited ainsi quaux clauses applicables stipules dans le FAR et ses supplments.

Avis de non-responsabilit: les seules garanties octroyes par Fujitsu Limited, Sun Microsystems, Inc. ou toute socit affilie de lune ou lautre entit enrapport avec ce document ou tout produit ou toute technologie dcrit(e) dans les prsentes correspondent aux garanties expressment stipules dans le contratde licence rgissant le produit ou la technologie fourni(e). SAUF MENTION CONTRAIRE EXPRESSMENT STIPULE DANS CE CONTRAT, FUJITSULIMITED, SUN MICROSYSTEMS, INC. ET LES SOCITS AFFILIES REJETTENT TOUTE REPRSENTATION OU TOUTE GARANTIE,QUELLE QUEN SOIT LA NATURE (EXPRESSE OU IMPLICITE) CONCERNANT CE PRODUIT, CETTE TECHNOLOGIE OU CE DOCUMENT,LESQUELS SONT FOURNIS EN LTAT. EN OUTRE, TOUTES LES CONDITIONS, REPRSENTATIONS ET GARANTIES EXPRESSES OUTACITES, Y COMPRIS NOTAMMENT TOUTE GARANTIE IMPLICITE RELATIVE LA QUALIT MARCHANDE, LAPTITUDE UNEUTILISATION PARTICULIRE OU LABSENCE DE CONTREFAON, SONT EXCLUES, DANS LA MESURE AUTORISE PAR LA LOIAPPLICABLE. Sauf mention contraire expressment stipule dans ce contrat, dans la mesure autorise par la loi applicable, en aucun cas Fujitsu Limited,Sun Microsystems, Inc. ou lune de leurs filiales ne sauraient tre tenues responsables envers une quelconque partie tierce, sous quelque thorie juridique quece soit, de tout manque gagner ou de perte de profit, de problmes dutilisation ou de perte de donnes, ou dinterruptions dactivits, ou de tout dommageindirect, spcial, secondaire ou conscutif, mme si ces entits ont t pralablement informes dune telle ventualit.

LA DOCUMENTATION EST FOURNIE EN LETAT ET TOUTES AUTRES CONDITIONS, DECLARATIONS ET GARANTIES EXPRESSES OUTACITES SONT FORMELLEMENT EXCLUES, DANS LA MESURE AUTORISEE PAR LA LOI APPLICABLE, Y COMPRIS NOTAMMENT TOUTEGARANTIE IMPLICITE RELATIVE A LA QUALITE MARCHANDE, A LAPTITUDE A UNE UTILISATION PARTICULIERE OU A LABSENCE DECONTREFACON.


6/192


7/192

v

Contents

Preface xvii

1. Rack Overview 11

1.1 Equipment Rack Types 12

1.2 Equipment Rack Selection Procedure 16

1.2.1 Consideration of Rack fixation for Quake Resistance 16

1.2.2 Selection of Equipment Rack 16

1.2.3 Selection of Rack Fixation Method 17

1.2.4 Quake-resistant Options Kit 17

1.2.5 Arrangements for Equipment Rack Installation 18

1.3 Appearance of the Equipment Rack 19

1.4 Floor Plans of the Equipment Rack 120

2. Overview of Hardware Units to Be Mounted 21

2.1 Outline of Hardware Units That Can Be Mounted 21

2.2 Appearance of Units 23

2.3 Power Supply Connection 26

2.3.1 SPARC Enterprise M3000 Server 27




8/192

vi SPARC Enterprise Equipment Rack Mounting Guide June 2009

2.3.4 External I/O Expansion Unit 216

2.3.5 Power Distribution Box 219

3. Mounting Units in the Rack 31

3.1 Rack Mounting Examples 31

3.2 Service Area 32

3.2.1 When a Stepladder Is Not Used 33

3.2.2 When a Stepladder Is Used 34

3.3 Restriction on Mounting and Requirements for Maintenance 35

3.3.1 Mounting Restriction and Requirements for Maintenance of the SPARCEnterprise M3000 Server 35



3.3.4 External I/O Expansion Unit Mounting Restriction 311

3.4 Equipment Rack Mounting Requirements 312

3.4.1 When Using the Pull-out Quake-Resistant Options Kit 313

3.4.2 When Using the Bolt-on Quake-Resistant Options Kit 313

3.4.3 When You Take Measures to Fixate the Rack for Quake Resistance 314

3.4.4 Cable Routing Inside the Rack 316

3.4.5 Other Requirements 316

3.5 Procedure for Mounting the SPARC Enterprise M3000 Server in the Rack 317

3.5.1 Components Check List 317

3.5.2 Safety Against Overturning 320

3.5.3 Attaching the Slide Rails 320

3.5.4 Checking of Installed Slide Rails 334

3.5.5 Attaching the Cable Management Arm 336




9/192

Contents vii

3.6.2 Proper Securing of Cables for Server Mount Conditions 341

3.6.3 Safety Against Overturning 343

3.6.4 Attaching the Slide Rails 3443.6.5 Attaching the Cable Management Arm 351

3.6.6 Attaching the Cable Bracket 358



3.7.2 Safety Against Overturning 3723.7.3 Attaching the Slide Rails 373

3.7.4 Installation Procedure of Cable Management Arm and Cable Bracket 381

3.7.5 Securing the Cables 394

3.8 Procedure for Mounting the Power Distribution Box in the Rack 399

3.9 Mounting the Server in a Rack Produced by a Company Other Than Fujitsu 3100

3.9.1 Rack Stability Requirements 3101

3.9.2 Requirements Concerning Rack Depth 3101

3.9.3 Rack Column Requirements 3104

3.9.4 Cable Routing inside the Rack 3105

3.9.5 Other Requirements 3105

4. Considerations Regarding Carrying-in and Installation 41

4.1 Load Requirements of an Elevator 41

4.2 Earthquake Preparedness Measures 42


10/192

viii SPARC Enterprise Equipment Rack Mounting Guide June 2009


11/192

ix

Figures

FIGURE 1-1 Appearance of Base Rack of the Equipment Rack for the SPARC Enterprise Servers (Model

Name: SE-R7RC11) 110

FIGURE 1-2 Appearance of System Cabinet of the Equipment Rack for the SPARC Enterprise Servers

(Model Name: SE-R7RC21) 111

FIGURE 1-3 Appearance of Base Rack of the Equipment Rack for the SPARC Enterprise Servers (ModelName: SE-R8RC11) 112

FIGURE 1-4 Appearance of System Cabinet of the Equipment Rack for the SPARC Enterprise Servers

(Model Name: SE-R8RC21) 113

FIGURE 1-5 Appearance of Base Rack of the Equipment Rack Model 1640 (Model Name: 19R-

164A1/19R-164A2) 114

FIGURE 1-6 Appearance of System Cabinet of the Equipment Rack Model 1640 (Model Name: 19R-

164B1/19R-164B2) 115


162A1/19R-162A2) 116


162B1/19R-162B2) 117


174A1/19R-174A2) 118


174B1/19R-174B2) 119

FIGURE 1-11 Floor Plan of the Equipment Rack for SPARC Enterprise Servers 121

FIGURE 1-12 Floor Plan of the Equipment Rack Model 1640/1620 122

FIGURE 1-13 Floor Plan of the Equipment Rack Model 1740 123

FIGURE 1-14 Floor Plan of the Equipment Rack with the Pull-out Quake-Resistant Options Kit Mounted 124


12/192

x SPARC Enterprise Equipment Rack Mounting Guide June 2009

FIGURE 1-15 Floor Plan of Interconnected Equipment Racks for SPARC Enterprise Servers 125

FIGURE 1-16 Floor Plan of Interconnected Equipment Racks Model 1640/1620 125

FIGURE 1-17 Floor Plan of Interconnected Equipment Racks Model 1740 126FIGURE 2-1 SPARC Enterprise M3000 Server Appearance 23

FIGURE 2-2 SPARC Enterprise M4000 Server Appearance 24

FIGURE 2-3 SPARC Enterprise M5000 Server Appearance 25

FIGURE 2-4 Appearance of the External I/O Expansion Unit 26

FIGURE 2-5 Power Supply System Diagram with Redundant PSU Connection 27

FIGURE 2-6 Power Supply System Diagram with Dual Power Feed Connection 28





FIGURE 2-11 Power System in a Redundant Power Supply Configuration 216

FIGURE 2-12 Power System in a Dual-power Supply Configuration 217

FIGURE 2-13 For 100V for Use in Japan (Model Name: SE-R7CB11) 219

FIGURE 2-14 For 200V for Use in Japan (Model Name: SE-R7CB21) 220

FIGURE 2-15 For 100V for Use outside Japan (Model Name: SE-R7CB11X) 222

FIGURE 2-16 For 200V for Use outside Japan (Model Name: SE-R7CB21X) 223

FIGURE 3-1 Equipment Rack Mounting Examples 32

FIGURE 3-2 Service Area for Cases Where a Stepladder Is Not Used 33

FIGURE 3-3 Service Area in Cases Where a Stepladder Is Used 34

FIGURE 3-4 Mounting Restriction and Requirements for Maintenance of the SPARC Enterprise M3000

Server (when the 40U rack is used) 36





FIGURE 3-7 External I/O Expansion Unit Mounting Restriction 311

FIGURE 3-8 Pulling Out the Pull-out QuakeResistant Options Kit 313

FIGURE 3-9 Attaching the Bolt-on Quake-Resistant Options Kit 314


13/192

Figures xi

FIGURE 3-10 Anchoring Quake-Resistant Options Kits to the Floor 315

FIGURE 3-11 Example of the Affixing Rack with Level Foot 316

FIGURE 3-12Pulling Out the Pull-out Quake-Resistant Options Kit 320

FIGURE 3-13 Drawing Out the Inner Slide Rails 321

FIGURE 3-14 Attaching the Screw Plate 321

FIGURE 3-15 Attaching the Brackets 323

FIGURE 3-16 Attaching the Bracket-1 Attachment 324

FIGURE 3-17 Attaching the Bracket-2 Attachment 324

FIGURE 3-18 Attaching the Slide Rail Fitted with the Bracket-1 Attachment 326

FIGURE 3-19 Attaching the Slide Rail Fitted with the Bracket-2 Attachment 328

FIGURE 3-20 Attaching the Inner Slide Rails on the Server 329

FIGURE 3-21 Attaching the Inner Slide Rail Holding Bracket to the Inner Slide Rail 330

FIGURE 3-22 Inserting the Middle Slide Rail into the Outer Slide Rails 331

FIGURE 3-23 Sliding the Bearing Board 332

FIGURE 3-24 Inserting the Server into the Rack 333

FIGURE 3-25 Checking the Placement of the Slide Rails 335

FIGURE 3-26 Securing the Server to the Rack 336

FIGURE 3-27 Attaching the Cable Management Arm 337

FIGURE 3-28 Securing the Cables 338

FIGURE 3-29 Pulling Out the Pull-out Quake-Resistant Options Kit 343

FIGURE 3-30 Attaching the Cage Nuts 344

FIGURE 3-31 Attaching the Screw Plates 345

FIGURE 3-32 Fixing the Slide Rails in Position on the Rack 346

FIGURE 3-33 Securing the Inner Slide Rails in Place 347

FIGURE 3-34 Magnified view of Part A and Part B (unlocked) 347

FIGURE 3-35 Magnified view of Part A and Part B (locked) 348

FIGURE 3-36 Magnified view of Part A and Part B (unlocked) 348

FIGURE 3-37 Bearing Board in Full Forward Position Inside the Slide Rail 349

FIGURE 3-38 Inserting the Inner Slide Rails 350

FIGURE 3-39 Removing the Pedestal from the Bottom of the Server 351


14/192

xii SPARC Enterprise Equipment Rack Mounting Guide June 2009

FIGURE 3-40 Securing the Cable Management Arm with Screws 352

FIGURE 3-41 Unlock the Slide Rail 353

FIGURE 3-42

Securing the Server to the Rack 354FIGURE 3-43 Installing End Caps on the SPARC Enterprise M4000 Slide Rails 355

FIGURE 3-44 Cable Holder on the Rear Right of the Rack 356

FIGURE 3-45 Status of Cables When the Server Pulled Out 357

FIGURE 3-46 Status of Cables When the Server Secured to the Rack 358

FIGURE 3-47 Attaching the Cable Holding Brackets 359

FIGURE 3-48 Unlock the Slide Rail 360


FIGURE 3-50 Installing End Caps on the SPARC Enterprise M4000 Slide Rails 362


FIGURE 3-52 Securing Cables Other Than the Copper Link Cables 364

FIGURE 3-53 Moving the Cable Holder 365

FIGURE 3-54 Securing the Copper Link Cables 366


FIGURE 3-56 Bracket Kit That Is Attached to the Right Column on the Rear of the Rack 371

FIGURE 3-57 Pulling Out the Pull-out Quake-Resistant Options Kit 372


FIGURE 3-59 Attaching Screw Plates 374

FIGURE 3-60 Fixing the Slide Rails in Position on the Rack 375

FIGURE 3-61 Rear Right Column of the Rack 376

FIGURE 3-62 Attaching the Cage Nuts/Brackets 377

FIGURE 3-63 Sliding the Server 378

FIGURE 3-64 Setting the Pins in the Holes 379

FIGURE 3-65 Securing the Slide Rails 379

FIGURE 3-66 Removing the Pedestal from the Bottom of the Server 380

FIGURE 3-67 Folding the Cable Management Arm 382

FIGURE 3-68 Securing the Cable Management Arm with Screws 383

FIGURE 3-69 Unlocking 384


15/192

Figures xiii


FIGURE 3-71 Installing End Caps on the Left Rear of the SPARC Enterprise M5000 Slide Rails 386


FIGURE 3-73 Cable Bracket Kit 388

FIGURE 3-74 Attaching the Cable Holding Brackets 389

FIGURE 3-75 Unlocking 390


FIGURE 3-77 Installing End Caps on the Left Rear of the SPARC Enterprise M5000 Slide Rails 392



FIGURE 3-80 Securing Copper Link Cables 396

FIGURE 3-81 Securing the Optical Fiber Cables 397

FIGURE 3-82 Drawing Out the Server 398


FIGURE 3-84 Securing the Distribution Box 3100

FIGURE 3-85 Requirements Concerning Rack Depth 3102

FIGURE 3-86 Detailed Figure of the Slide Rail of the SPARC Enterprise M3000 Server 3103



FIGURE 3-89 Detailed Figure of the External I/O Expansion Unit Rack Mounting Rail 3104

FIGURE 3-90 Rack Column Requirements 3105


16/192

xiv SPARC Enterprise Equipment Rack Mounting Guide June 2009


17/192

xv

Tables

TABLE 1-1 Equipment Rack Types for SPARC Enterprise Servers 12

TABLE 1-2 Equipment Rack Model 1640 Types 13

TABLE 1-3 Equipment Rack Model 1620 Types 14

TABLE 1-4 Model 1740 Rack Types 15

TABLE 2-1 Hardware Units That Can Be Mounted 22

TABLE 2-2 Power Cord Outlet Specifications of M3000 Server 29



TABLE 2-5 Power Cord and Outlet Specifications of the External I/O Expansion Unit 218

TABLE 2-6 Power Cord and Outlet Specifications of the Power Distribution Box 219




TABLE 3-1 Conditions for Rack Mounting and Methods for Securing Cables 342

TABLE 4-1 Elevator Load Requirements 41


18/192


19/192

xvii

Preface

This manual describes the installation requirements and items for consideration wheninstalling the equipment rack. Before using the rack, be sure follow the instructions in thismanual and consult with a certified service engineer regarding its proper use.

This manual is intended for persons who are engaged in computer system installation siteplanning, persons who are actually installing computer systems, or persons who operate oradministrate such systems. Readers are assumed to have some knowledge and experience

involving installation site planning for computer systems.

This section includes:

Glossary on page xvii Structure and Contents of This Manual on page xviii SPARC Enterprise M3000/M4000/M5000 Servers Documentation on page xviii Text Conventions on page xxi Prompt Notations on page xxi

Syntax of the Command Line Interface (CLI) on page xxii Environment Requirements for Using This Product on page xxii Conventions for Alert Messages on page xxiii Notes on Safety on page xxiv Product Handling on page xxvii Fujitsu Welcomes Your Comments on page xxix

GlossaryFor the terms used in the SPARC EnterpriseTM Equipment Rack Mounting Guide, see theSPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers Glossary.


20/192

xviii SPARC Enterprise Equipment Rack Mounting Guide June 2009

Structure and Contents of This ManualThis manual is organized as described below:

Chapter 1 Rack Overview

This chapter provides an overview of the equipment rack.

Chapter 2 Overview of Hardware Units to Be Mounted

This chapter provides an overview of the hardware units that can be mounted in theequipment rack.

Chapter 3 Mounting Units in the Rack

This chapter provides considerations regarding the mounting of hardware units in theequipment rack.

Chapter 4 Considerations Regarding Carrying-in and Installation

This chapter provides considerations regarding the carrying-in and installation of theequipment rack.

SPARC Enterprise M3000/M4000/M5000Servers DocumentationThe manuals listed below are provided for reference.

Book Titles Manual Codes

SPARC Enterprise M3000 Server Site Planning Guide C120-H030

SPARC Enterprise M4000/M5000 Servers Site Planning Guide C120-H015

SPARC Enterprise Equipment Rack Mounting Guide C120-H016

SPARC Enterprise M3000 Server Getting Started Guide C120-E536

SPARC Enterprise M4000/M5000 Servers Getting Started Guide C120-E345

SPARC Enterprise M3000 Server Overview Guide C120-E537

SPARC Enterprise M4000/M5000 Servers Overview Guide C120-E346

Important Safety Information for Hardware Systems C120-E391

SPARC Enterprise M3000 Server Safety and Compliance Guide C120-E538

SPARC Enterprise M4000/M5000 Servers Safety and Compliance Guide C120-E348


21/192

Preface xix

1. Manuals on the WebThe latest versions of all the SPARC Enterprise Series manuals are available at thefollowing websites.

Global Site

http://www.fujitsu.com/sparcenterprise/manual/

Japanese Site

http://primeserver.fujitsu.com/sparcenterprise/manual/

External I/O Expansion Unit Safety and Compliance Guide C120-E457

SPARC Enterprise M4000 Server Unpacking Guide C120-E349SPARC Enterprise M5000 Server Unpacking Guide C120-E350

SPARC Enterprise M3000 Server Installation Guide C120-E539

SPARC Enterprise M4000/M5000 Servers Installation Guide C120-E351

SPARC Enterprise M3000 Server Service Manual C120-E540

SPARC Enterprise M4000/M5000 Servers Service Manual C120-E352

External I/O Expansion Unit Installation and Service Manual C120-E329

SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers RCI BuildProcedure

C120-E361

SPARC Enterprise M3000/M4000/M5000/M8000/M9000 ServersAdministration Guide

C120-E331

SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers XSCFUsers Guide

C120-E332

SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers XSCFReference Manual

C120-E333

SPARC Enterprise M4000/M5000/M8000/M9000 Servers DynamicReconfiguration (DR) Users Guide

C120-E335

SPARC Enterprise M4000/M5000/M8000/M9000 Servers Capacity onDemand (COD) Users Guide

C120-E336

SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers RCI Users

Guide

C120-E360

SPARC Enterprise M3000 Server Product Notes Go to the Web

SPARC Enterprise M4000/M5000 Servers Product Notes Go to the Web

External I/O Expansion Unit Product Notes C120-E456

SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers Glossary C120-E514

Book Titles Manual Codes


22/192

xx SPARC Enterprise Equipment Rack Mounting Guide June 2009

Note Product Notes are available on the website only. Please check for the recent updateon your product.

2. Documentation CD

For the Documentation CD, please contact your local sales representative.

SPARC Enterprise M3000 Server Documentation CD (C120-E541) SPARC Enterprise M4000/M5000 Servers Documentation CD (C120-E365)

3. Manual included on the Enhanced Support Facility x.x CD-ROM disk

Remote maintenance service

4. Provided in system

Man page of the XSCF

Note The man page can be referenced on the XSCF shell, and it provides the samecontent as the SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers XSCFReference Manual.

5. Solaris Operating System Related Manuals

http://docs.sun.com

6. Information on Using the RCI function

The manual does not contain an explanation of the RCI build procedure. For informationon using the RCI function, refer to the SPARC EnterpriseM3000/M4000/M5000/M8000/M9000 Servers RCI Build Procedure and SPARCEnterprise M3000/M4000/M5000/M8000/M9000 Servers RCI Users Guide provided onthe website.

Book Title Manual Code

Enhanced Support Facility User's Guide for REMCS C112-B067


23/192

Preface xxi

Text ConventionsThis manual uses the following fonts and symbols to express specific types of information.

Prompt NotationsThe following prompt notations are used in this manual.

Fonts/symbols Meaning Example

AaBbCc123 What you type, when contrasted withon-screen computer output.

This font represents the example ofcommand input in the frame.

XSCF> adduser jsmith

AaBbCc123 The names of commands, files, anddirectories; on-screen computeroutput.

This font represents the example ofcommand input in the frame.

XSCF> showuser -P

User Name: jsmith

Privileges: useradm

auditadm

Italic Indicates the name of a referencemanual

See the SPARC EnterpriseM3000/M4000/M5000/M8000/M900

0 Servers XSCF Users Guide." " Indicates names of chapters, sections,

items, buttons, or menusSee Chapter 2, "Overview ofHardware Units to Be Mounted."

Shell Prompt Notations

XSCF XSCF>

C shell machine-name%

C shell super user machine-name#

Bourne shell and Korn shell $

Bourne shell and Korn shell superuser

#

OpenBoot PROM ok


24/192

xxii SPARC Enterprise Equipment Rack Mounting Guide June 2009

Syntax of the Command Line Interface (CLI)The command syntax is as follows:

A variable that requires input of a value must be enclosed in . An optional element must be enclosed in [ ]. A group of options for an optional keyword must be enclosed in [ ] and delimited by |. A group of options for a mandatory keyword must be enclosed in { } and delimited by |. The command syntax is shown in a box.

Example:

Environment Requirements for Using ThisProductThis product is intended to be used in a computer room.

XSCF> showuser -a


25/192

Preface xxiii

Conventions for Alert MessagesThis manual uses the following conventions to show alert messages, which are intended to

prevent injury to the user or bystanders as well as property damage, and important messagesthat are useful to the user.

WARNING:This indicates a hazardous situation that could result in death or serious personal injury(potential hazard) if the user does not perform the procedure correctly.

CAUTION:This indicates a hazardous situation that could result in minor or moderate personal injury ifthe user does not perform the procedure correctly. This signal also indicates that damage tothe product or other property may occur if the user does not perform the procedure correctly.

IMPORTANT:This indicates information that could help the user to use the product more effectively.

Alert Messages in the Text

An alert message in the text consists of a signal indicating an alert level followed by an alertstatement. Alert messages are indented to distinguish them from regular text. Also, a space ofone line precedes and follows an alert statement.

WARNING:

The tasks listed below for this product and optional product provided by Fujitsu SiemensComputers should be performed only by authorized service personnel.

The user must not perform these tasks. Incorrect operation of these tasks may cause electricshock, injury, or fire.

Installation and reinstallation of all components Removal of front, rear, or side covers Mounting/unmounting of optional internal devices

Connecting/disconnecting of external interface cables Maintenance (repair and regular diagnosis and maintenance)

Also, important alert messages are shown in Important Alert Messages on page xxiv.


26/192

xxiv SPARC Enterprise Equipment Rack Mounting Guide June 2009

Notes on Safety

Important Alert Messages

This manual provides the following important alert signals:

Caution The WARNING signal indicates a dangerous situation could result in death orserious injury if the user does not perform the procedure correctly.

Task Warning

Normaloperation

Electric shock, fire

Do not damage, break, or modify the power cords. Cable damage may causeelectric shock or fire.


27/192

Preface xxv

Caution The CAUTION signal indicates a hazardous situation could result in minor ormoderate personal injury if the user does not perform the procedure correctly. This signalalso indicates that damage to the product or other property may occur if the user does not

perform the procedure correctly.

Task Warning

Normaloperation

Equipment damage

Be sure to follow the precautions below when installing the server. Otherwise, theequipment may be damaged.

Do not block ventilation slits.

Avoid installing the equipment in a place exposed to direct sunlight or nearequipment that becomes extremely hot.

Avoid installing the equipment in a dusty place or a place directly exposed tocorrosive gas or salty air.

Avoid installing the equipment in a place exposed to strong vibration. Also,install the equipment on a level surface so that it is stable.

The grounding wire must be class 3 or higher. Connecting it with anothergrounding wire for shared grounding may cause a malfunction. Be sure to use

a single grounding path for the grounding wire. Do not run any cable beneath any equipment. Also, prevent cables from

becoming taut. Never disconnect any power cord from the equipment whilepower is being supplied to the equipment.

Do not place anything on top of the server. Do not use the server as aworkspace.

Avoid exposing the equipment to rapid changes in the ambient temperature,such as a rapid increase during transport in winter. A rapid increase in the

ambient temperature causes moisture to condense in the equipment. Use theequipment only after the difference between its temperature and the ambienttemperature is negligible.

Avoid installing the equipment near a copy machine, air conditioner, or weldingmachine, which is noisy.

Take preventive action to minimize static electricity at the installation location.Note that static electricity is easily generated in some carpets and can cause theequipment to malfunction.

Confirm that the power supply voltage and frequency during operation match

the rated values indicated on the equipment. Do not insert any object into an opening in the equipment. Components inside

the equipment use high voltage. Conductive foreign matter, such as a metalobject, inserted into the equipment, may cause a short circuit betweencomponents, resulting in fire, electric shock, or equipment damage.

For maintenance of the equipment, contact your authorized service personnel.


28/192

xxvi SPARC Enterprise Equipment Rack Mounting Guide June 2009

Normaloperation

Data destruction

Confirm the items listed below before turning off the power. Otherwise, data may

be destroyed. All applications have completed processing.

No user is using the equipment.

When the server power is turned off, the Power LED on the operation panel isturned off. Be sure to confirm that the Power LED is off before turning off themain power (uninterruptible power supply [UPS], power distribution box, mainline switch, etc.).

If necessary, back up files before turning off the system power.

Data destruction

Do not forcibly stop a domain that is operating normally. Otherwise, data may bedestroyed.

Data destruction

Do not disconnect the power cord from the AC power input while power is beingsupplied. Otherwise, data stored on hard disk units may be destroyed.

Task Warning


29/192


30/192

xxviii SPARC Enterprise Equipment Rack Mounting Guide June 2009

Emission of Laser Beam (Invisible)

Caution The server and high-speed optical interconnect cabinet contain modules thatgenerate invisible laser radiation. Laser beams are generated while the equipment isoperating, even if an optical cable is disconnected or a cover is removed. Do not look at anylight-emitting part directly or through an optical apparatus (e.g., magnifying glass,microscope).


31/192

Preface xxix

Fujitsu Welcomes Your CommentsIf you have any comments or requests regarding this document, or if you find any unclearstatements in the document, please state your points specifically on the form at the followingURL.

For Users in U.S.A., Canada, and Mexico:

http://www.computers.us.fujitsu.com/www/support_servers.shtml?su

pport/servers

For Users in Other Countries:

SPARC Enterprise contact

http://www.fujitsu.com/global/contact/computing/sparce_index.html


32/192

xxx SPARC Enterprise Equipment Rack Mounting Guide June 2009


33/192

1-1

CHAPTER 1

Rack Overview

This chapter contains information on the equipment racks, on which the SPARC EnterpriseM3000/M4000/M5000 Servers are mounted. Rack types, appearance views, and floor plansare shown below. Equipment Rack Types on page 2 Appearance of the Equipment Rack on page 9 Floor Plans of the Equipment Rack on page 20


34/192

1-2 SPARC Enterprise Equipment Rack Mounting Guide June 2009

1.1 Equipment Rack TypesTABLE 1-1, TABLE 1-3 and TABLE 1-4 show the equipment racks on which SPARC EnterpriseM3000/M4000/M5000 Servers can be mounted.

*1:The value does not include the weight of the rack itself.

*2:The weight of the rack alone includes the weight of the tip-resistant quake-resistant options kits.

*3:When a system cabinet is used, it is connected with the base rack. Also, system cabinets can be interconnected. (The interconnected cabinets mustbe of the same height.)

*4:In model names, * is any letter from A to Z.

TABLE 1-1 Equipment Rack Types for SPARC Enterprise Servers

Item

Model name

(*4) Rack types

Rack size

[mm (in.)] Weight [kg (lb.)]

RemarksWidth Depth Height

Total

mountable

weight (*1)

Rack

alone

Totalweight

of the

rack

1 SE-R7RC11 * 40U baserack

700(27.6)

1050(41.3)

2000(78.8)

800 (1760) 200(440)(*2)

1000(2200)

With a sidepanelWith aquake-resistant

options kit

2 SE-R7RC21 * 40U systemcabinet (*3)

700(27.6)

1050(41.3)

2000(78.8)

800 (1760) 165(363)(*2)

965(2123)

Without aside panelWith aquake-resistantoptions kit

3 SE-R8RC11 * 36U baserack

700(27.6)

1050(41.3)

1800(70.9)

720 (1584) 180(396)(*2)

900(1980)

With a sidepanelWith aquake-resistantoptions kit

4 SE-R8RC21 * 36U systemcabinet (*3)

700(27.6)

1050(41.3)

1800(70.9)

720 (1584) 155(341)(*2)

875(1925)

Without aside panelWith a

quake-resistantoptions kit


35/192

Chapter 1 Rack Overview 1-3



*3:When a system cabinet is used, it is connected with the base rack. Also, system cabinets can be interconnected. (The interconnected cabinets must

be of the same height.)*4:In model names, * is any letter from A to Z.

TABLE 1-2 Equipment Rack Model 1640 Types

Item

Model name

(*4) Rack types

Rack size



Total

mountable

weight (*1)

Rack

alone

Total

weight

of the

rack

1 19R-164A1 * 40U baserack

600(23.6)

1050(41.3)

2000(78.8)

800 (1760) 126(277)(*2)

926(2037)

With a sidepanelWith a


2 19R-164B1 * 40U systemcabinet (*3)

600(23.6)

1050(41.3)

2000(78.8)

800 (1760) 94(206)(*2)

894(1966)



600(23.6)

1050(41.3)

2000(78.8)

800 (1760) 118(256)

918(2019)

With a sidepanelWithout aquake-resistantoptions kit

4 19R-164B2 * 40U system

cabinet (*3

)

600

(23.6)

1050

(41.3)

2000

(78.8)

800 (1760) 86

(189)

886

(1949)

Without a

side panelWithout aquake-resistantoptions kit


36/192





be of the same height.)*4:In model names, * is any letter from A to Z.

TABLE 1-3 Equipment Rack Model 1620 Types

Item

Model name

(*4) Rack types

Rack size



Total

mountable

weight (*1)

Rack

alone

Total

weight

of the

rack


600(23.6)

1050(41.3)

1264(49.7)

480 (1056) 94(206)(*2)

574(1262)



2 19R-162B1 * 24U systemcabinet (*3)

600(23.6)

1050(41.3)

1264(49.7)

480 (1056) 75(165)(*2)

555(1221)



600(23.6)

1050(41.3)

1264(49.7)

480 (1056) 86(189)

566(1245)

With a sidepanelWithout aquake-resistantoptions kit

4 19R-162B2 * 24U system

cabinet (*3

)

600

(23.6)

1050

(41.3)

1264

(49.7)

480 (1056) 67

(147)

547

(1203)

Without a

side panelWithout aquake-resistantoptions kit


37/192





be of the same height.)

TABLE 1-4 Model 1740 Rack Types

Item Model name Rack types

Rack size



Total

mountable

weight (*1)

Rack

alone

Total

weight

of the

rack

1 19R-174A1 40U baserack

700(27.6)

1050(41.3)

2000(78.8)

800 (1760) 143

(315)(*2)

943(2075)



2 19R-174B1 40U systemcabinet (*3)

700(27.6)

1050(41.3)

2000(78.8)

800 (1760) 110(242)(*2)

910(2002)


3 19R-174A2 40U baserack

600(23.6)

1050(41.3)

2000(78.8)

800 (1760) 135(297)

935(2057)

With a sidepanelWith aquake-resistantoptions kit

4 19R-174B2 40U system

cabinet (*3

)

600

(23.6)

1050

(41.3)

2000

(78.8)

800 (1760) 102

(224)

902

(1984)

Without a

side panelWith aquake-resistantoptions kit


38/192


1.2 Equipment Rack Selection Procedure

1.2.1 Consideration of Rack fixation for Quake Resistance

Before you select the equipment rack, make sure whether or not you take measures to fixatethe rack for quake resistance, depending on the level of customer's requirement for quakeresistance and the conditions of the building.

When you take measures to fixate the rack, it withstands the acceleration of up to 1,000 galat the time of earthquake in general buildings.

When you do not take measures to fixate the rack, select the rack to which the tip-resistancequake-resistant options kit attached. When you perform maintenance on the server mountedon the rack, use the quake-resistant options kit to prevent the rack from toppling over. In thiscase, it withstands the acceleration of up to 250 gal at the time of earthquake in general

buildings.

1.2.2 Selection of Equipment Rack

When you take measures to fixate the rack, select the rack to which the tip-resistance quake-resistant options kit not attached, and see Section 1.2.3, Selection of Rack Fixation Methodon page 1-7.

When you do not take measures to fixate the rack, select the rack to which the tip-resistancequake-resistant options kit attached, and see Section 1.2.5, Arrangements for EquipmentRack Installation on page 1-8.

Note Regardless of whether or not the building or the floor is quake-resistant (seismicisolated), when you do not take measures to fixate the rack, do not fail to select the rack towhich the tip-resistance quake-resistant options kit attached. When you perform maintenanceon the server mounted on the rack, use the quake-resistant options kit to prevent the rackfrom toppling over.


39/192

1 2 5 Arrangements for Equipment Rack Installation


40/192


1.2.5 Arrangements for Equipment Rack Installation

*1:The bolts to fixate the rack to the building are supposed to be arranged by theconstructors.

*2:There are two kinds of quake-resistant options kit; the kit for the base rack and the kit forthe system cabinet.

Options kit for the base rack:Parts for the front (x1), parts for the rear (x1), parts for the side (x2), set of fixing bolts

Options kit for the system cabinet:

Parts for the front (x1), parts for the rear (x1), set of fixing bolts

When the quake-resistant options kit for the base rack applied to the system cabinet,the parts for the side of the rack become redundant.

When the quake-resistant options kit for the system cabinet applied to the base rack, itlacks the parts for the side of the rack. It is not permitted to operate the system withoutattaching the parts for the side.

*3:You can select the rack to which the tip-resistant quake-resistant options kit attached anduse the quake-resistant options kit to fixate it. However, there are limitations as follows.

When the tip-resistant quake-resistant options kit is the pull-out quake-resistant optionskit:

You can't attach the quake-resistant options kit and the pull-out quake-resistant optionskit at the same time. You need to detach the pull-out quake-resistant options kit beforeyou attach the quake-resistant options kit.

When the tip-resistant quake-resistant options kit is the bolt-on quake-resistant optionskit:

Among the components included in the quake-resistant options kit, the parts for thefront of the rack (front parts) become redundant.

1. Consider whether or not

fixate the rack. 2. Select the rack. 3. Select the fixation method. 4. Arrange the options.

When you fixate theequipment rack

You can select the rack towhich the tip-resistancequake-resistant options kitnot attached.

Fixate the rack by using thequake-resistant options kit.

Quake-resistant options kit.(See *1 and *2.)

Fixate the rack by using thelevel feet.

None. (See *1.)

When you do not fixate theequipment rack

You must select the rack towhich the tip-resistance

quake-resistant options kitattached.

- (See *3 and *4.) None.

*4:You can select the rack to which the tip-resistant quake-resistant options kit attached and


41/192


use the level feet to fixate it with the quake-resistant options kit remain attached. In thiscase, the quake-resistant options kit becomes functionally unnecessary.

1.3 Appearance of the Equipment RackThis section provides the following illustrations:

FIGURE 1-1 Appearance of Base Rack of the Equipment Rack for the SPARC Enterprise

Servers (Model Name: SE-R7RC11), FIGURE 1-2 Appearance of System Cabinet of theEquipment Rack for the SPARC Enterprise Servers (Model Name: SE-R7RC21), FIGURE 1-3Appearance of Base Rack of the Equipment Rack for the SPARC Enterprise Servers (Model

Name: SE-R8RC11), and FIGURE 1-4 Appearance of System Cabinet of the Equipment Rackfor the SPARC Enterprise Servers (Model Name: SE-R8RC21).

FIGURE 1-5 Appearance of Base Rack of the Equipment Rack Model 1640 (Model Name:19R-164A1/19R-164A2), FIGURE 1-6 Appearance of System Cabinet of the Equipment RackModel 1640 (Model Name: 19R-164B1/19R-164B2), FIGURE 1-7 Appearance of Base Rackof the Equipment Rack Model 1620 (Model Name: 19R-162A1/19R-162A2), and FIGURE 1-8Appearance of System Cabinet of the Equipment Rack Model 1620 (Model Name: 19R-162B1/19R-162B2).

FIGURE 1-9 Appearance of Base Rack of the Equipment Rack Model 174 (Model Name: 19R-174A1/19R-174A2), and FIGURE 1-10 Appearance of System Cabinet of the Equipment RackModel 1740 (Model Name: 19R-174B1/19R-174B2).

Base Rack of the Equipment Rack for the SPARC Enterprise Servers Model Name: SE-R7RC11


42/192


R7RC11

FIGURE 1-1 Appearance of Base Rack of the Equipment Rack for the SPARC Enterprise Servers (Model Name: SE-

R7RC11)

Front View Right Side Rear View

Unit: mm (in.)

Top View

System Cabinet of the Equipment Rack for the SPARC Enterprise Servers Model Name:SE R7RC21


43/192


SE-R7RC21

FIGURE 1-2 Appearance of System Cabinet of the Equipment Rack for the SPARC Enterprise Servers (Model Name:

SE-R7RC21)


Unit: mm (in.)

Top View

Base Rack of the Equipment Rack for the SPARC Enterprise Servers Model Name: SE-R8RC11


44/192


R8RC11

FIGURE 1-3 Appearance of Base Rack of the Equipment Rack for the SPARC Enterprise Servers (Model Name: SE-

R8RC11)


Unit: mm (in.)

Top View

System Cabinet of the Equipment Rack for the SPARC Enterprise Servers Model Name:SE-R8RC21


45/192


SE R8RC21

FIGURE 1-4 Appearance of System Cabinet of the Equipment Rack for the SPARC Enterprise Servers (Model Name:

SE-R8RC21)


Unit: mm (in.)

Top View

Base Rack of the Equipment Rack Model 1640 Model Name: 19R-164A1/19R-164A2


46/192


FIGURE 1-5 Appearance of Base Rack of the Equipment Rack Model 1640 (Model Name: 19R-164A1/19R-164A2)

1050 (41.3)

2

000

(78.

8)

600(23.6)


Unit: mm (in.)

Top View

System Cabinet of the Equipment Rack Model 1640 Model Name: 19R-164B1/19R-164B2


47/192


FIGURE 1-6 Appearance of System Cabinet of the Equipment Rack Model 1640 (Model Name: 19R-164B1/19R-

164B2)

1050 (41.3)

600(23.6)

2000

(7

8.

8)


Unit: mm (in.)

Top View



48/192



1050 (41.3)

1264

(49.

8)

600 (23.6)


Unit: mm (in.)

Top View



49/192



162B2)

1050 (41.3)

600 (23.6)

12

64

(49.

8)


Unit: mm (in.)

Top View



50/192




Unit: mm (in.)

Top View



51/192



174B2)


Unit: mm (in.)

Top View

1 4 Fl Pl f th E i t R k


52/192


1.4 Floor Plans of the Equipment RackThis section provides the floor plans of the equipment Rack.

Floor Plan of the Equipment Rack (FIGURE 1-11, FIGURE 1-12)

Floor Plan of the Equipment Rack with the Pull-out quake-resistant options kit Mounted(FIGURE 1-14)

Floor Plan of Interconnected Equipment Racks (FIGURE 1-15, FIGURE 1-16, FIGURE 1-17)


53/192

FIGURE 1-12 Floor Plan of the Equipment Rack Model 1640/1620


54/192


Caster

level feet

Unit: mm (in.)

Legend:

Cable extraction (insertion) hole

(At the center of the level foot, there is a 17 mm-deep,M20-size screw hole used for securing the rack in position.)

Quake-resistant options kit

Floor hole for securing the quake-resistant options kit

Front of the unit

FIGURE 1-13 Floor Plan of the Equipment Rack Model 1740


55/192


Caster

level feet

Unit: mm (in.)

Legend:



Quake-resistant options kit

Floor hole for securing the quake-resistant options kit

Front of the unit

Floor Plan of the Equipment Rack with the Pull-out Quake-Resistant Options KitMounted


56/192


FIGURE 1-14 Floor Plan of the Equipment Rack with the Pull-out Quake-Resistant Options Kit Mounted

Caster

Unit: mm (in.)

Front ofthe unit

Legend:


level feet


SizewhenthePull-out

quake-resistantoptionskitis

pull

edout

Floor Plan of Interconnected Equipment Racks

FIGURE 1-15 Floor Plan of Interconnected Equipment Racks for SPARC Enterprise Servers


57/192


FIGURE 1-16 Floor Plan of Interconnected Equipment Racks Model 1640/1620

Front of the unit

Unit: mm (in.)

Level feet

Caster

977

(38.

5)

36.

5

(1.

4)

775

(30.

5)

137.

5

(5.

4)

600 (23.6) 600 (23.6) 600 (23.6) 40.5

81

(3.2)

81

(3.2)

81

(3.2)

40.5(1.6) (1.6)

519 (20.4) 519 (20.4) 519 (20.4) 519 (20.4)

100100

(3.9) (3.9)

200

(7.8)

400

(15.7)

200

(7.8)

400

(15.7)

200

(7.8)

400

(15.7)

400

(15.7)

Front of the unit

Unit: mm (in.)

level feet

Caster

FIGURE 1-17 Floor Plan of Interconnected Equipment Racks Model 1740

Front of the unit


58/192


Unit: mm (in.)

level feet

Caster

CHAPTER 2


59/192

2-1

Overview of Hardware Units to BeMounted

Outline of Hardware Units That Can Be Mounted on page 2-1 Appearance of Units on page 2-3 Power Supply Connection on page 2-6

2.1 Outline of Hardware Units That Can BeMountedThe SPARC Enterprise M3000/M4000/M5000 Servers and the External I/O Expansion Unitcan be mounted in the equipment rack.

This chapter provides an overview of each unit.

TABLE 2-1 Hardware Units That Can Be Mounted

E t l di i


60/192


*1: The value indicates the weight for when all options are mounted.

*2: The value indicates the depth including the cable management arm.

Product name

External dimensions

[mm (in)] Weight (*1)

[kg (lb.)] RemarksWidth Depth Height

SPARC EnterpriseM3000 Server

440

(17.4)

657

(25.9)

87

(3.4)

2U

22

(48.5)

Equipment rack-mount typeSPARC Enterprise Serverunit.

Up to 1 CPU can be mountedin the 2U-size server.

SPARC EnterpriseM4000 Server 444(17.5) 810(31.9) 263(10.35)6U

84(185) Equipment rack-mount typeSPARC Enterprise Serverunit.

Up to 4 CPUs can bemounted in the 6U-sizeserver.

SPARC EnterpriseM5000 Server

444

(17.5)

810

(31.9)

440

(17.32)

10U

125

(275)

Equipment rack-mount typeSPARC Enterprise Serverunit.

Up to 8 CPUs can bemounted in the 10U-sizeserver.

External I/OExpansion Unit)

440

(17.32)

1000

(39.4)(*2)

175

(6.9)

4U

37

(81)

Unit for expanding the PCIslots.

Up to 12 PCIX or Expressslots can be installed perunit.

Up to two units can beconnected to the M4000server and up to four unitscan be connected to theM5000 server.

2.2 Appearance of Units


61/192

Chapter 2 Overview of Hardware Units to Be Mounted 2-3

This section provides the appearance of the units. SPARC Enterprise M3000 Server Appearance on page 2-3 (FIGURE 2-1) SPARC Enterprise M4000 Server Appearance on page 2-4 (FIGURE 2-2) SPARC Enterprise M5000 Server Appearance on page 2-5 (FIGURE 2-3) Appearance of the External I/O Expansion Unit on page 2-6 (FIGURE 2-4)

FIGURE 2-1 SPARC Enterprise M3000 Server Appearance

Front View Right Side

Top View



62/192



Top View



63/192



Top View

FIGURE 2-4 Appearance of the External I/O Expansion Unit


64/192


2.3 Power Supply ConnectionThis section provides input power system diagrams for individual hardware units as well asthe power cord and outlet specifications of the units:

Section 2.3.1, SPARC Enterprise M3000 Server on page 2-7 Section 2.3.2, SPARC Enterprise M4000 Server on page 2-10 Section 2.3.3, SPARC Enterprise M5000 Server on page 2-13 Section 2.3.4, External I/O Expansion Unit on page 2-16 Section 2.3.5, Power Distribution Box on page 2-19

Caution Use only the power cords supplied with this product to connect this product. Donot to use these power cords with other products.


Top View

2.3.1 SPARC Enterprise M3000 Server

This section explains the power supply connections of the SPARC Enterprise M3000 server.

Power supply system diagram with redundant PSU connection


65/192


pp y y g

FIGURE 2-5 Power Supply System Diagram with Redundant PSU Connection

Note If more than one power cord of this server is connected directly to the customer'sdistribution panel, connect the power cords to outlets independently using one cable per

power feed as shown in FIGURE 2-5.

Note If connected to uninterruptible power supply (UPS) or the power distribution box,you do not have to connect the power cords one-on-one but can connect the cords in acollective form within the range of current capacity of UPS or the power distribution box.

PSU#0 PSU#1

AC Power Supply

CB: Circuit breaker

(overcurrent protection device)

CB

CB

Power supply system diagram with dual power feed connection

FIGURE 2-6 Power Supply System Diagram with Dual Power Feed Connection


66/192




Note For dual power feed connection, connect the individual power cords separately toeach AC power supply system.

PSU#0 PSU#1

AC Power Supply

CB: Circuit breaker(overcurrent protection device)

CB

CB

TABLE 2-2 Power Cord Outlet Specifications of M3000 Server

DeliveryPlug type Outlet type


67/192


Note For the servers that have the B-type plug, confirm that a 15A overcurrent protectiondevice is available outside the server. If not, prepare an external 15A overcurrent protectionthat can be achieved by means of no-fuse breakers (NFBs) or fuses. The B-type plug refersto plugs other than grounding-type ones with two parallel blades, such as the NEMA L6-30,L6-20, L6-15, and L5-15.

Delivery

destination Specifications Shape Specifications Shape

Japan andoutside Japan,100 VAC

Two-parallel-prong plugwith grounding electrode(125 V, ** A)

[NEMA standard typename: 5-15P]

* Connect it to the powerdistribution box, or

prepare an outlet for theunit.

Receptacle for paralleltwo-prong plug withgrounding electrode

(125V15A)[NEMA 5-15R]


* Option

Three-prong twist-lockplug with groundingelectrode (250 V, 15 A)

[NEMA standard typename: L6-15P]

* Connect it to the powerdistribution box, or

prepare an outlet for theunit.

Receptacle for three-pronghook type plug with

grounding electrode(250V15A)

[NEMA L6-15R]





68/192






PSU#0 PSU#1Customer's distribution panel

#1

#0


CB




69/192





PSU#0 PSU#1

Customer's distribution panel

#1#0


CB

CB



Delivery

d i i

Plug type Outlet type

S ifi i Sh S ifi i Sh


70/192


Note The plug (NEMA L6-20) of the power cords supplied with the SPARC EnterpriseM4000/M5000 servers has the following dimensions. Confirm in advance that the plug doesnot become an obstruction when plugged into the input power source at the installation site.- Outside diameter of the connector part of the plug: 50 mm- Maximum outside diameter of the plug cover: 57 mm

- Plug cover length from the connector end: 69.9 mm



For use inJapan/Forgeneral useoutside Japan

AC200V

Three-prong hook typeplug with groundingelectrode

(250V20A)

[NEMA L6-20P]

* Prepare the outlet for anoutlet for the unit.

Receptacle for three-pronghook type plug withgrounding electrode(250V20A)

[NEMA L6-20R]

3220-L6 (AmericanDenki) or other

China / Korea /Hong Kong

Option

AC200V


(250V13A)

[IEC60320-C14]



[IEC60320-C13]





71/192






PSU#0Customer's distribution panel

#1

#2

CB: Circuit breaker


CB

#3

#0PSU#2 PSU#3PSU#1




72/192





CB: Circuit breaker


CB

CB#1

#2

#3

#0

Customer's

PSU#0 PSU#2 PSU#3PSU#1

distribution panel

Customer'sdistribution panel


Delivery

destination

Plug type Receptacle type

Specifications Shape Specifications Shape


73/192


Note The plug (NEMA L6-20) of the power cords supplied with the SPARC EnterpriseM4000/M5000 servers has the following dimensions. Confirm in advance that the plug doesnot become an obstruction when plugged into the input power source at the installation site.- Outside diameter of the connector part of the plug: 50 mm- Maximum outside diameter of the plug cover: 57 mm

- Plug cover length from the connector end: 69.9 mm



For use inJapan/Forgeneral useoutside Japan

AC200V


(250V20A)

[NEMA L6-20P]



[NEMA L6-20R]

3220-L6 (AmericanDenki) or other

China / Korea /Hong Kong

Option

AC200V


(250V13A)

[IEC60320-C14]



[IEC60320-C13]

2.3.4 External I/O Expansion Unit

This section explains the power supply connections of the External I/O Expansion Unit.

Power system in a redundant power supply configuration


74/192


FIGURE 2-11 Power System in a Redundant Power Supply Configuration

*1: Connect one power cord to each output group (one circuit breaker [CB] with two outlets) of the power distribution box.To maintain redundancy, connect no peripheral to the other outlet.

PSU#1


CB

CB(15A)

#1

#0

No connection (*1)

No connection (*1)

CB(15A)

CB(15A)

Power distribution box (option)


PSU#0

Power system in a dual-power supply configuration

FIGURE 2-12 Power System in a Dual-power Supply Configuration

Power distribution box (option)


75/192


*1: Connect one power cord to each output group (one circuit breaker [CB] with two outlets) of the power distribution box.To maintain redundancy, connect no peripheral to the other outlet.


CB

#1

#0

No connection (*1)

CB(15A)

( p )


CB

CB(15A)

CB(15A)

No connection (*1)

CB: Circuit breaker


TABLE 2-5 Power Cord and Outlet Specifications of the External I/O Expansion Unit

Delivery

destination

Plug type Receptacle type

Specifications Shape Specifications Shape


76/192




Two-parallel-prong plugwith grounding electrode(125 V, ** A)

[NEMA standard typename: 5-15P]

* Connect it to the powerdistribution box, or preparean outlet for the unit.

Receptacle for parallel two-prong plug with groundingelectrode (125V15A)

[NEMA 5-15R]


* Option

Three-prong twist-lockplug with groundingelectrode (250 V, 15 A)

[NEMA standard typename: L6-15P]

* Connect it to the powerdistribution box, or preparean outlet for the unit.


[NEMA L6-15R]

Embedded type:3120/3120-P/3120-D(American Denki)

Exposed type: 3121(American Denki)

2.3.5 Power Distribution Box

This section explains the power supply connections of the power distribution box.

For 100V for use in Japan (Model name: SE-R7CB11)


77/192


FIGURE 2-13 For 100V for Use in Japan (Model Name: SE-R7CB11)

TABLE 2-6 Power Cord and Outlet Specifications of the Power Distribution Box

Delivery

destination

Output receptacle type Input plug type Receptacle type on equipment

Specifications Shape Specifications Shape Specifications Shape

Japan,100 VAC

* Option

Outlet for two-parallel-prongplug withgroundingelectrode (125 V,

15 A) (lockmechanism)

[NEMA 5-15R]

Three-prongtwist-lock plugwith groundingelectrode (125 V,30 A)

[NEMA L5-30P]

Outlet for three-prongtwist-lock plug withgrounding electrode(125 V, 30 A)

[NEMA L5-30R]

Embedded type: 3310-L5(American Denki)

Exposed type: 3311-L5(American Denki)


CB(15A)

CB(15A)

CB(15A)

CB(15A)

Output

Outlet Overcurrent protection device (CB)

group 1Outputgroup 2

Outputgroup 3

Outputgroup 4

Maximum 12A/group

Maximum 12A

/group

Maximum 12A/group

Maximum 12A/group

Total:

Maximum 24A

For 200V for use in Japan (Model name: SE-R7CB21)

FIGURE 2-14 For 200V for Use in Japan (Model Name: SE-R7CB21)

Total:


78/192



Delivery

destination



Japan,200 VAC

* Option

Outlet for three-prong twist-lockplug withgroundingelectrode (250 V,15 A)

[NEMA L6-15R]


[NEMA L6-30P]

* Outlet for three-prong twist-lock plugwith groundingelectrode (250 V, 30 A)

[NEMA L6-30R]

Embedded type: 3320-L6

(American Denki)

Exposed type: 3321-L6

(American Denki)

CB: Circuit breaker


CB(15A)

CB(15A)

CB(15A)

CB(15A)


Output

group 1

Output

group 2

Output

group 3

Output

group 4

Maximum 12A/group

Maximum 12A/group

Maximum 12A

/group

Maximum 12A/group

Total:

Maximum 24A

Note For the servers that have the B-type plug, confirm that a 30A overcurrent protectiondevice is available outside the server. If not, prepare an external 30A overcurrent protectionthat can be achieved by means of no-fuse breakers (NFBs) or fuses. The B-type plug refersto plugs other than grounding-type ones with two parallel blades, such as the NEMA L6-30,

L6-20, L6-15, and L5-15.


79/192


For 100V for use outside Japan (Model name: SE-R7CB11X)

FIGURE 2-15 For 100V for Use outside Japan (Model Name: SE-R7CB11X)

Total:


80/192



Delivery

destination



Outside Japan,100 VAC

* Option

Outlet for two-parallel-prongplug withgroundingelectrode (125 V,15 A) [NEMA 5-15R]


[NEMA L5-30P]

* Outlet for three-prong twist-lock plugwith groundingelectrode(125 V, 30 A)

[NEMA L5-30R]

CB: Circuit breaker


CB(15A)

CB(15A)

CB(15A)

CB(15A)


CB(15A)

CB(15A)

CB(15A)

CB(15A)

Maximum 12A

Maximum 12A

Maximum 12A

Maximum 12A

Maximum 12A

Maximum 12A

Maximum 12A

Maximum 12A

Total:

Maximum 24A

For 200V for use outside Japan (Model name: SE-R7CB21X)

FIGURE 2-16 For 200V for Use outside Japan (Model Name: SE-R7CB21X)

Total:


81/192




Delivery

destination



Outside Japan,200 VAC

* Option

IEC320-C13 type Three-prongtwist-lock plugwith groundingelectrode (250 V,30 A)

[NEMA L6-30P]

* Outlet for three-prong twist-lock plugwith groundingelectrode (250 V, 30 A)

[NEMA L6-30R]


CB(15A)

CB(15A)

CB(15A)

CB(15A)


CB(15A)

CB(15A)

CB(15A)

CB(15A)

Maximum 12A

Maximum 12A

Maximum 12A

Maximum 12A

Maximum 12A

Maximum 12A

Maximum 12A

Maximum 12A

Total:

Maximum 24A


82/192


CHAPTER 3


83/192

3-1

Mounting Units in the Rack

Rack Mounting Examples on page 3-1 Service Area on page 3-2

Restriction on Mounting and Requirements for Maintenance on page 3-5

Equipment Rack Mounting Requirements on page 3-12

Procedure for Mounting the SPARC Enterprise M3000 Server in the Rack on page 3-17

Procedure for Mounting the SPARC Enterprise M4000 Server in the Rack on page 3-39

Procedure for Mounting the SPARC Enterprise M5000 Server in the Rack on page 3-68 Procedure for Mounting the Power Distribution Box in the Rack on page 3-99

Mounting the Server in a Rack Produced by a Company Other Than Fujitsu on page 3-100

3.1 Rack Mounting ExamplesUp to 20 SPARC Enterprise M3000 Server units, 5 SPARC Enterprise M4000 Server units,or 3 SPARC Enterprise M5000 Server units can be mounted in the equipment rack. AnExternal I/O Expansion Unit added to a SPARC Enterprise M4000/M5000 Servers unit must

be mounted in the same rack. The equipment rack can also be used as an I/O expansion rackfor the SPARC Enterprise M8000/M9000 Server.

FIGURE 3-1 shows mounting examples.

The left shows the case when 15 SPARC Enterprise M3000 Server units. The center showsthe case when 5 SPARC Enterprise M4000 Server units and an External I/O Expansion Unitmounted in the equipment rack, and the right shows the case when 3 SPARC EnterpriseM5000 Server units and an External I/O Expansion Unit mounted.

FIGURE 3-1 Equipment Rack Mounting Examples

External I/OExpansion Unit

External I/OExpansion Unit


84/192


3.2 Service AreaThe SPARC Enterprise M3000/M4000/M5000 Servers are accessed from the top surfaces. Astepladder may be required for maintenance depending upon the height these servers aremounted in the rack. Secure an adequate service area for maintenance work depending uponthe height the server is mounted in the rack. For information on mounting locations in a rackthat require use of a stepladder, see Section 3.3, Restriction on Mounting and Requirementsfor Maintenance on page 3-5.

SPARC Enterprise

M5000 ServerSPARC Enterprise

M4000Server

SPARC EnterpriseM3000Server

3.2.1 When a Stepladder Is Not Used

FIGURE 3-2 shows the service area for cases where a stepladder is not used.

FIGURE 3-2 Service Area for Cases Where a Stepladder Is Not Used


85/192

Chapter 3 Mounting Units in the Rack 3-3

Unit: mm (in.)

M4000

M5000

Service area

Service area

*

M3000

When the equipment rack model 1640/1620 is used : 600 (23.6)

3.2.2 When a Stepladder Is Used

FIGURE 3-3 shows the service area for when a stepladder is used. When a stepladder is used,the area must be secured so that the stepladder can be oriented both perpendicularly to and in

parallel with the server.

FIGURE 3-3 Service Area in Cases Where a Stepladder Is Used


86/192


Documents

Rackmount en 10