Quick Glance Class Specs

8/9/2019 Quick Glance Class Specs

1/3

SPORTSMAN DIVISION

CLASSSTOCK GROUP MODIFIED SPORTSMAN GROUP

STOCK SUPER STOCK

NOSTALGIA

PRO STOCK RATT ROD

CHASSIS

Configuration Legacy T-Jet only Legacy T-Jet only All T-Jet Types All T-Jet Types

Alterations Minimum Minimum Moderate Moderate

ELECTRICAL

Armature 16 OHMS min. 16 OHMS min. 14 OHMS min. 14 OHMS min.

Motor Brushes conventional conventional after-market after-market

Pick-Ups after-market after-market after-market after-market, mod.

Braids None Permitted None Permitted Permitted Permitted

Shunts None Permitted None Permitted None Permitted Permitted

MAGNETS

Motor conventional conventional conventional conventionalTraction None Permitted None Permitted Permitted Permitted

Tires / Wheels

Height .410 max. .460 max. .450 max. .382-.485 max.

Width .100 max. .215 max. .230 max. .28125 max.

Composition rubber / silicone rubber / silicone rubber / silicone rubber / silicone

BODY

Style Am. 1960-1972 Am. 1960-1972 Am. 1965-1979 Am. 1925-1969

Mods None Permitted Minimum Moderate Extreme

Ballast Permitted Permitted Permitted Permitted

Windows Factory supplied Factory supplied Front, rear reqd Front, rear reqd

GEARS

Pinion conventional conventional 9t,10t,11t,12t,14t 9t,10t,11t,12t,14t

Crown conventional conventional 15t,19t 15t,19t

MISCELLANEOUS

Scoops / Chutes None Permitted None Permitted Permitted Permitted

Wheelie Bars None Permitted None Permitted Permitted Permitted

GLOSSARYAfter-market refers to exact or near exact stock replacement which may or may not minimally improve performance.

Conventional stock or near stock replacement designed to perform as factory original.

Minimum alterations allowed primarily allowing better fitting of components. No noticeable performance increase. Chassis may have any and all of the following:de-burring, clearancing, polishing, hardening and/or blueprinting.

Moderate alterations which enhance performance. Chassis may have any and all of the following: de-burring, clearancing, polishing, hardening and/or blueprinting.

Main chassis may NOT be altered. (No cuts) The rails of the top plate may be removed as shown in order to facilitate body mounting. (show diagram) A

T Jet top plate may be reamed to allow fitment of a JL/AW armature to the T Jet chassis. Top plate may not be otherwise altered.Extreme maximum alterations allowed to enhance performance.

Factory supplied stock or as supplied with unit when new.

Complete rules & specifications available here: http://www.psychoslots.com/index.cgi?board=skr


2/3

COMPETITION DIVISION

CLASS

GASSER ALTERED

NOSTALGIA

FUNNY CAR

CHASSIS

Configuration All T-Jet Types All T-Jet Types All T-Jet TypesAlterations moderate moderate moderate

ELECTRICAL

Armature 5 OHMS min. 5 OHMS min. 5 OHMS min.

Motor Brushes After-market After-market After-market

Pick-Ups After-market After-market After-market

Braids Permitted Permitted PermittedShunts Permitted Permitted Permitted

MAGNETS

Motor conventional conventional conventionalTraction Permitted Permitted Permitted

Tires / Wheels

Height .382 - .485 max. .382 - .485 max. .500 max.

Width .28125 max. .28125 max. .260 max.

Composition Any readily available Any readily available Any readily available

BODY

Style Am. 1935 - 1969 1927 - 1946 Funny Car 1964 - 1977

Mods Moderate Extreme Moderate

Ballast Permitted Permitted Permitted

Windows Front reqd Not reqd Front, rear reqd

GEARS

Pinion 9t,10t,11t,12t,14t 9t,10t,11t,12t,14t 9t,10t,11t,12t,14t

Crown 15t,19t 15t,19t 15t,19t

MISCELLANEOUS

Scoops / Chutes Permitted Permitted PermittedWheelie Bars Permitted Permitted Permitted

GLOSSARYAfter-market refers to exact or near exact stock replacement which may or may not minimally improve performance.Conventional stock or near stock replacement designed to perform as factory original.Minimum alterations allowed primarily allowing better fitting of components. No noticeable performance increase.

Moderate 1. alterations which enhance performance. Chassis may have any and all of the following: de-burring, clearancing, polishing, hardening and/or

blueprinting. Main chassis may be altered as follows: All side areas between motor magnets may be day-lighted

(see Figure one) Chassis top plate may be modifiedextensively but must employ four (4) corner mountings as produced by the manufacturer. Incidental modifications, such as drilling for wheelie bar attachment or ballast

attachment is permitted. All other chassis modifications are prohibited.

2. Body posts may be shortened/lengthened and body may be raised or lowered. Bodies must employ at least one (1) mounting screw. No lexan bodieswill be permitted in this class. Bodies shall be of Injection molded plastic or resin or poured resin. Fenders are required. Running boards may be removed. Wheel

wells may be radiused as needed but must follow profile of racing tire used. Fender flares are permitted. Front chin spoilers are permitted, however they should not be

extreme in size.Extreme maximum alterations allowed to enhance performance.Factory supplied stock or as supplied with unit when new.

Complete rules & specifications available here: http://www.psychoslots.com/index.cgi?board=skr


3/3

PRO DIVISION

CLASS

NTRA ISRA

PRO MOD FUNNY CAR

TOP FUEL

DRAGSTER

MM/

PRO STOCK

CHASSIS

Configuration - - - Any Inline

Alterations - - - Moderate

ELECTRICAL

Armature - - - 2.6 OHMS min.

Motor Brushes - - - Unlimited R/A

Pick-Ups - - - Unlimited R/A

Braids - - - Permitted

Shunts - - - Permitted

MAGNETS

Motor - - - Ceramic onlyTraction - - - Permitted

Tires / Wheels

Height - - - Unlimited R/A

Width - - - Unlimited R/A

Composition - - - Unlimited R/A

BODY

Style - - - 1980 - present

Mods - - - Moderate

Ballast - - - Permitted

Windows - - - Front, rear reqd

GEARS

Pinion - - - Unlimited R/A

Crown - - - Unlimited R/A

MISCELLANEOUS

Scoops / Chutes - - - Permitted

Wheelie Bars - - - Permitted

Weight - - - 23.0gm minimum

GLOSSARYAfter-market refers to exact or near exact stock replacement which may or may not minimally improve performance.Conventional stock or near stock replacement designed to perform as factory original.Minimum alterations allowed primarily allowing better fitting of components. No noticeable performance increase.

Moderate 1. alterations which enhance performance. Chassis can be Cut, Drilled, Sanded and Braced to stiffen.

Wheelie bars are allowed.

2. All bodies must have a Front Window, Rear Window, Hood Scoop, Rear Air Spoil or Wing. Each body musthave a front and rear bumper.

Extreme maximum alterations allowed to enhance performance.

Factory supplied stock or as supplied with unit when new.R/A- readily available.

Complete rules & specifications available here: http://www.psychoslots.com/index.cgi?board=klgkdlkl&action=display&thread=366

Documents

Quick Glance Class Specs