Upload
dinhkien
View
223
Download
3
Embed Size (px)
Citation preview
Pyroelectric InfraredSensors
Cat.No.S21E-4
MurataManufacturing Co., Ltd.
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
S21E.pdf 05.11.16
CONTENTS
Dual Type Pyroelectric Infrared Sensor IRA-E700 Series
Quad Type Pyroelectric Infrared Sensor IRA-E900 Series
Quad Type Pyroelectric Infrared Sensor IRA-E940ST1 Series
Temperature Compensation Single Type Pyroelectric Infrared Sensor
IRA-E420 Series
1
2
3
4
5
7
10
13
1
2
3
4
Fresnel Lens
Notice
Pyroelectric Infrared Sensor IRA Series Characteristics Data
Part Numbering
Recycled Paper
HIC® in this catalog are the trademarks ofMurata Manufacturing Co., Ltd.
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
S21E.pdf 05.11.16
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
S21E.pdf 05.11.16
1
o Part Numbering
Pyroelectric Infrared Sensor
qProduct ID
wType
eCharacteristics
rIndividual Specification Code
* Part Number shows only an example which might be differentfrom actual part number.* "eCharacteristics" and "rIndividual Specification Code" mighthave different digit number from actual Part Number.
IR(Part Number) A- E710ST 1
q w e r
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
S21E.pdf 05.11.16
1
2
Dual Type Pyroelectric Infrared Sensor IRA-E700 Series
Pyroelectric Infrared Sensors
Pyroelectric infrared sensors, IRA series, exhibit highsensitivity and reliable performance made possible byMurata's ceramic technology and Hybrid IC techniqueexpertise developed over many years.IRA-E700 series realizes cost benefits and higherperformance with a new infrared sensor element ofimproved material parameters and fabrication.IRA-E700 series is available in two types.IRA-E710ST0 has enhanced immunity to RFI (RadioFrequency Interference).
! Features1. High sensitivity and excellent S/N ratio2. High stability to temperature changes3. Slight movement can be detectable.4. High immunity to external noise (Vibration, RFI etc.)5. Custom design is available.6. Higher in cost-performance
! Applications1. Security2. Lighting appliances3. Household or other appliances
!Rating (25˚C)
! Dimensions & Circuit Diagrams
g
sRG
d
g
sRG
d
5.0±0.05 ∗
d s
g
9.2
4.7±0.1
3.7±
0.1
11.0
±2φ0.45±0.05
4.7
45°
45°3.
6
1.0 1.0 1.0
2.0
Pyroelectric element
IRA-E700ST0
(in mm)
∗ Specified on the bottom of stem
General Tolerance : ±0.2
(in mm)
IRA-E710ST0
Part Number
Responsivity (500K, 1Hz, 1Hz)
Field of View
Optical Filter
Electrode
Supply Voltage
Operating Temperature
Storage Temperature
4.3mVp-p (Typ.)
θ1=θ2=45°
5µm long-pass
(2.0Z1.0mm)Z2
2 to 15V
-40 to 70D
-40 to 85D
IRA-E700ST0 IRA-E710ST0
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
S21E.pdf 05.11.16
2
3
Quad Type Pyroelectric Infrared Sensor IRA-E900 Series
Pyroelectric Infrared Sensors
Pyroelectric infrared sensors, IRA series, exhibit highsensitivity and reliable performance made possible byMurata's ceramic technology and Hybrid IC techniqueexpertise developed over many years.IRA-E900 series realizes cost benefits and higherperformance with a new infrared sensor element ofimproved material parameters and fabrication.IRA-E900 series is available in two types.IRA-E910ST1 has enhanced immunity to RFI (RadioFrequency Interference).
! Features1. High sensitivity and excellent S/N ratio2. High stability to temperature changes3. Slight movement can be detectable.4. Non directional sensing with wide F.O.V.5. High immunity to external noise (Vibration, RFI etc.)6. Custom design is available.7. Higher in cost-performance
! Applications1. Security2. Lighting appliances3. Household or other appliances
! Rating (25˚C)
! Dimensions & Circuit Diagrams
5.08±0.05∗
d s
g
1.1 1.0 1.1
9.2
4.7±0.1
1.1
1.0
1.1
g
s
RG
YWWYYWWY
WYYW
WYYW
d
g
s
RG
YWWYYWWY
WYYW
WYYW
d
11.0
±2φ0.45±0.05
4.7
41°
3.6
41°
Pyroelectric element
IRA-E900ST1
(in mm)
(in mm)
IRA-E910ST1
∗ Specified on the bottom of stem
General Tolerance : ±0.2Part Number
Responsivity (500K, 1Hz, 1Hz)
Field of View
Optical Filter
Electrode
Supply Voltage
Operating Temperature
Storage Temperature
3.3mVp-p (Typ.)
θ1=θ2=41°
5µm long-pass
(1.1Z1.1mm)Z4
3 to 15V
-25 to 55D
-40 to 85D
IRA-E900ST1 IRA-E910ST1
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
S21E.pdf 05.11.16
3
4
Quad Type Pyroelectric Infrared Sensor IRA-E940ST1 Series
Pyroelectric Infrared Sensors
Pyroelectric infrared sensors, IRA series, exhibit highsensitivity and reliable performance made possible byMurata's ceramic technology and Hybrid IC techniqueexpertise developed over many years.IRA-E940ST1 realizes cost benefits and higher performancewith a new infrared sensor element of improved materialparameters and fabrication.IRA-E940ST1 which has quad elements and 2 outputs willdetect the human body more correctly with OR/AND logiccircuit.
! Features1. High sensitivity and excellent S/N ratio2. High stability to temperature changes3. High immunity to external noise (Vibration, RFI etc.)4. Higher in cost-performance5. Custom design is available.
! Applications1. Security2. Lighting appliances3. Household or other appliances
! Rating (25˚C)
! Dimensions & Circuit Diagrams
5.08±0.05∗
s1 d
s2g
1.0 0.8
(Y) W
(Y) W
Y (W)
Y (W)
1.0
9.2
4.7±0.1
1.35
0.3
1.35
RG
RG
s1
d
s2
g
11.0
±2φ0.45±0.05
4.7
55°
3.6
50°
Pyroelectric element
(in mm)
(in mm)
∗ Specified on the bottom of stem
General Tolerance : ±0.2
Part Number
Responsivity (500K, 1Hz, 1Hz)
Field of View
Optical Filter
Electrode
Supply Voltage
Operating Temperature
Storage Temperature
3.3mVp-p (Typ.)
θ1=55°, θ2=50°
5µm long-pass
(1.35Z1.0mm)Z4
2 to 15V
-25 to 55D
-40 to 85D
IRA-E940ST1
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
S21E.pdf 05.11.16
(IRA-E420SW1)! Dimensions & Circuit Diagrams
(IRA-E420S1, IRA-E420QW1)
1.5
max
.
9.2
3.6 4.
5
d s
g
5.08±0.05∗
ø0.45±0.05
50°
11±2
3.0±0.1
5.08±0.05∗
d s
g
11.0
±2
ø0.45±0.05
4.9
9.2
2.4±0.1
17°
17°
3.6
1.8Pyroelectric element
1.6Pyroelectric element
RGs
g
d
(in mm)
4
5
Temperature Compensation Single Type Pyroelectric Infrared Sensor IRA-E420 Series
Pyroelectric Infrared Sensors
Single type pyroelectric infrared sensors IRA-E420 serieshave a temperature compensation element.They are suitable for flame detection and gas detection.
! Features1. High stability against abrupt ambient temperature changes2. High immunity to external noise (Vibration, RFI etc.)3. Custom design is available with varying optical filter.
! Applications
Part Number
IRA-E420S1
IRA-E420QW1
IRA-E420SW1
Silicon
4.3µm band-pass
4.45µm band-pass
1-15µm infrared detection
Flame detection
Flame detection
Optical Filter Applications
(in mm)
∗ Specified on the bottom of stem
General Tolerance : ±0.2(in mm)
∗ Specified on the bottom of stem
General Tolerance : ±0.2(in mm)
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
S21E.pdf 05.11.16
4
6
! Rating (25˚C)
* 700K, 5Hz, 1Hz
Part Number
Responsivity (500K, 1Hz, 1Hz)
Field of View
Optical Filter
Electrode
Supply Voltage
Operating Temperature
Storage Temperature
3.4mVp-p (Typ.)
Silicon
-25 to 70D
IRA-E420S1
1.3mVp-p (Typ.)*
4.3µm band-pass
-25 to 55D
IRA-E420QW1
θ1=θ2=17°
ø1.6mm
3 to 15V
-30 to 100D
0.45mVp-p (Typ.)
θ1=θ2=50°
4.45µm band-pass
ø1.8mm
-25 to 70D
IRA-E420SW1
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
S21E.pdf 05.11.16
4
7
Pyroelectric Infrared Sensor IRA Series Characteristics Data
! Spectral Response of Window Materials
! Frequency Characteristics
2.5
4000 3500 3000 2500 2000 1800
Wave number (cm-1)
Tra
nsm
ittan
ce (
%)
Wave length (µm)
4.3µm Band-Pass Filter
7µm Long-Pass Filter
Silicon Filter
1600 1400 1200 1000 800
100
0
20
40
60
80
3.0 4.0 5.0 6.0 7.0 8.0 10.0 12.0
5µm Long-Pass Filter
1.0
Chopping Frequency (Hz)
Rel
ativ
e R
espo
nsiv
ity (
RV
)
1
10
10
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
S21E.pdf 05.11.16
4
8
Pyroelectric Infrared Sensor IRA Series Characteristics Data
! Test Method of Sensitivity
140mm
Black Body
500K*1
Mechanical Chopper1Hz*1
Infrared Sensor
Oscilloscope
g
s
47kΩ
W22µF
d
W5V
Lock-in Amplifier (1Hz)
D
g
B102K LM358330k B222K
260k 100k 4 8
1CB103K
R
5
2
6
7
3
100k
2SD596
µPD5555G
100k
1k
Photo Coupler
Relay
220k
220k
NJM2903M
330k
3.3µ16V
10µ16V
100k
100k
S
B102K
100k120k
4.7µ16V
1
120k B102K
10M
10M
B222K
1S184 B102KW
W
WW
10µ16V
LM358
1S184
100µ16V
100µ16V
9Y15
GND
78L05
3 Terminal Regulater
TH=1.1ZC (µF) Z R (MΩ) second
W
W W
! Typical Application Circuit (Human Detection)
*1 IRA-E420QW1
IRA-E420SW1
IRA-E700/E900 Series
700K
400K
500K
Black Body
5Hz
2.5Hz
1Hz
Mechanical Chopper
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
S21E.pdf 05.11.16
4
9
Pyroelectric Infrared Sensor IRA Series Characteristics Data
After test completion, leave for three hours in
normal humidity temperature conditions, and
then measure.
1. External appearance:
No significant damage
2. Sensitivity:
Tolerance within 20% deviation from original
value
3. Noise:
Maximum tolerance W100mV of original value
No generation of bubbles
! Reliability TestIRA-E700 series, IRA-E900 series
IRA-E420 series
Item
High Temperature
Low Temperature
Humidity
Heat Cycle
Vibration
Shock
Soldering Heat
Hermetic Sealing
100D for 500 hrs.
Y40D for 500 hrs.
60D, 95% RH for 500 hrs.
20 times of following cycle.
Y25D, 30 min.eRoom temp., 30 min.h
gRoom temp., 30 min.f55D, 30 min.
Apply vibration of amplitude of 1.5mm with 10 to 55Hz band to each of 3
perpendicular directions for 60 min.
Apply shock of 100G sinewave by standard shock tester to each of 3
perpendicular directions.
Immerse up to 3.0mm from can case in solder bath of 260T5D for 10T1 s.
Conform to MIL-STD-202F chapter 112D, condition D.
Immerse in fluorocarbon bath (FC-40) of 125T5D for 20 s.
Test Conditions Criteria
Item
High Temperature
Low Temperature
Humidity
Heat Cycle
Vibration
Shock
Soldering Heat
Hermetic Sealing
100D for 500 hrs.
Y30D for 500 hrs.
60D, 95% RH for 500 hrs.
20 times of following cycle.
Y25D, 30 min.eRoom temp., 30 min.h
gRoom temp., 30 min.f55D, 30 min.
Apply vibration of amplitude of 1.5mm with 10 to 55Hz band to each of 3
perpendicular directions for 60 min.
Apply shock of 100G sinewave by standard shock tester to each of 3
perpendicular directions.
Immerse up to 3.0mm from can case in solder bath of 260T5˚C for 10T1 s.
Conform to MIL-STD-202F chapter 112D, condition D.
Immerse in fluorocarbon bath (FC-40) of 125T5D for 20 s.
Test Conditions
After test completion, leave for three hours in
normal humidity temperature conditions, and
then measure.
1. External appearance:
No significant damage
2. Sensitivity:
Tolerance within 20% deviation from original
value
3. Noise:
Maximum tolerance W100mV of original value
No generation of bubbles
Criteria
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
S21E.pdf 05.11.16
4
10
m3.0
2.0
1.0
0
1.0
2.0
3.0 1.0 2.0 3.0 4.0 5.0 m
1.0 2.0
7.7m
29.6R
9m
10m
9m
7.7m
2m
1m1.6m
3.5m 10m
12°
3.0 4.0
BB' A
CC'
C'
C'B'
B'
BD
BC
C
D'
D'
D
A
A
D, D'
E, E'
30°
22.5°
5.0 m
m4.0
3.0
2.0
1.0
0
Horizontal Area Vertical Area
Horizontal Area Vertical Area
Sensor
29.6R
0.7max.
810
21.5
44.5
Lens plane
Sensor
16.3
C
DD
'
EE
'
BA
B'
C'
2.24
11.6
4 R
3.60
6.4
5.0
3.64
Cross-Sectional View
E'
E16.0
φ21.0
φ20.0
51.5
56.5
(in mm)
(in mm)
PPGI0601
PPGI0902
Pyroelectric Infrared Sensors/Fresnel Lens
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
S21E.pdf 05.11.16
4
11
16.5
6
12.9SR
Y
C12 C2
C11 C3
C1
C10X
C9 C5
C4 Z
0.8m
2.2m
2.5m
0.5m
YY
32
10
12
3
C
(m)
BA
BC
A : 0°B : 21.8°C : 48°
C8 C6
C7
B1
B4
B5
B6
B3
B2
12.1SR
3
3.6
Pyr
oele
ctric
elem
ent
2 3
φ23T0.2
φ21.4
φ19.4
A
B
C
Detection area on the floor
B : 60° pitch C : 30° pitch
(in mm)
PPGI0626
Pyroelectric Infrared Sensors/Fresnel Lens
1) Insert a sensor into Fresnel lens like each tab is overlapped.(In case there are two tabs on Fresnel lens, the field of view is determined by your choice (TabA or B on Fresnel lens).Please see following page(s) for more details to see which characteristic of field of view is preferable for your application.)
2) Push the sensor into Fresnel lens until the top face of sensor reaches to the stopper inside Fresnel lens.
3) Please prepare a housing yourself that is put onto Fresnel lens as shown in FigureA. The hatching area shown in Figure A, must be obscured by the housing in order to prevent mis-detection. Unless otherwise unexpected infrared ray comes though the hatching area.
4.5
Tab
5.7
8.65
4.05.
5
1.15
ø9.0
5.2 5.7
R4.8
3.01.15
4.353.
4
Pyro-Element
Step
ø8.2
(in mm)General tolerance : ±0.2
Housing
9.15
(4.3
5)
Figure A
13º13º (4.5)
*Assembled with Murata sensor IRA-700 series
Horizontal
10.8
m35
º35
º
0m
6m
6m
Vertical
1.8m
5m
0m
2m
2m
IML-0635
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
S21E.pdf 05.11.16
4
12
Pyroelectric Infrared Sensors/Fresnel Lens
1) Insert a sensor into Fresnel lens like each tab is overlapped.(In case there are two tabs on Fresnel lens, the field of view is determined by your choice (TabA or B on Fresnel lens).Please see following page(s) for more details to see which characteristic of field of view is preferable for your application.)
2) Push the sensor into Fresnel lens until the top face of sensor reaches to the stopper inside Fresnel lens.
3) Please prepare a housing yourself that is put onto Fresnel lens as shown in FigureA. The hatching area shown in Figure A, must be obscured by the housing in order to prevent mis-detection. Unless otherwise unexpected infrared ray comes though the hatching area.
(in mm)General tolerance : ±0.2
Housing
9.15
(4.3
5)
Figure A
13º13º (4.5)
4.5
Tab0.5
0.5
8.65
ø9.0
ø10.4
3.4
0.5
Focal point (Pyro-Element)
Step
ø8.2
Horizontal
5.54
m
*Assembled with Murata sensor IRA-700 series
6.6m
19.3
º19
.3º
19.3
º19
.3º
0m
4m
4mVertical
5m
0m
3m
3m
Freshel lens are available upon request.
IML-0636
1) Insert a sensor into Fresnel lens like each tab is overlapped.(In case there are two tabs on Fresnel lens, the field of view is determined by your choice (TabA or B on Fresnel lens).Please see following page(s) for more details to see which characteristic of field of view is preferable for your application.)
2) Push the sensor into Fresnel lens until the top face of sensor reaches to the stopper inside Fresnel lens.
3) Please prepare a housing yourself that is put onto Fresnel lens as shown in FigureA. The hatching area shown in Figure A, must be obscured by the housing in order to prevent mis-detection. Unless otherwise unexpected infrared ray comes though the hatching area.
(in mm)General tolerance : ±0.2
Housing
9.15
(4.3
5)
Figure A
13º13º (4.5)
4.5
Tab0.5
0.5
8.65
ø9.0
ø10.4
3.4
0.5
Focal point (Pyro-Element)
Step
ø8.2
*Assembled with Murata sensor IRA-700 series
Horizontal Vertical
1.8m
5m
0m
2m
2m
2.7m
5m
0m
2m
2m
IML-0637
1) Insert a sensor into Fresnel lens like each tab is overlapped.(In case there are two tabs on Fresnel lens, the field of view is determined by your choice (TabA or B on Fresnel lens).Please see following page(s) for more details to see which characteristic of field of view is preferable for your application.)
2) Push the sensor into Fresnel lens until the top face of sensor reaches to the stopper inside Fresnel lens.
3) Please prepare a housing yourself that is put onto Fresnel lens as shown in FigureA. The hatching area shown in Figure A, must be obscured by the housing in order to prevent mis-detection. Unless otherwise unexpected infrared ray comes though the hatching area.
4.5
Tab
5.7
8.65
4.05.
5
1.15
ø9.0
5.2 5.7
R4.8
3.01.15
4.353.
4
Pyro-Element
Step
ø8.2
(in mm)General tolerance : ±0.2
Housing
9.15
(4.3
5)
Figure A
13º13º (4.5)
6.11m
4.91m
3m
3m
0m
Vertical
3m
On the Floor
3m
45.5°
3m0m
45.5°
42°
42°
Horizontal
Vertical
Pyroelectric ElementHorizontal
Assembled with Murata sensor IRA-700 Series.
IML-0638
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
S21E.pdf 05.11.16
13
Notice
1. Caution (Design)(1) Please make sure that your product has been evaluated
and confirmed against your specifications when ourproduct is mounted to your product.
(2) Be sure to provide an appropriate fail-safe function onyour product to prevent a second damage that may becaused by the abnormal function or the failure of ourproduct.
(3) In case of outdoor use, suitable optical filter and waterand humidity proof structure should be applied.
(4) To prevent failure or malfunction, please use a stabilizedpower supply.
(5) Please avoid using the sensor in the following conditionsbecause it may cause failure or malfunction.(a) in such a fluid as water, alcohol etc. corrosive gas
(SO2, Cl2, NOX etc.) or sea breeze(b) in high humidity(c) in a place exposed directly to sunlight or headlights of
automobile(d) in a place exposed to rapid ambient temperature
change(e) in a place exposed directly to an air-conditioner or
heat vent(f) strong vibrations(g) in a place exposed to strong electromagnetic field(h) in such a place where infrared ray is shaded(i) in any other place similar to the above (a) through (h)
2. Caution (Mounting)(1) Soldering
(a) Hand soldering should be applied.
(b) Soldering should be done quickly as following.
(c) Soldering flux should be rosin flux and not containmore than 0.2wt% chlorine.Soldering flux should be removed after soldering.
(2) CleaningSoldering flux should be removed after soldering.Soldering flux may cause malfunction or degradation ofcharacter unless sufficiently cleaned.
3. Caution (Handling and Storage)(1) The optical filter of the sensor should not be scratched or
soiled.(2) Strong shock should be avoided.(3) Electrostatics and strong electromagnetic field should be
avoided.(4) The sensor should be kept on conductive sponge.(5) High temperature, high humidity, fluid such as water or
alcohol etc., corrosive gas (SO2, Cl2, NOX etc.) and seabreeze should be avoided.
! Notice
Temperature of soldering iron : 350˚C
Distance from can case
1 to 3mm
Over 3mm
Period of time
Within 3 seconds per point
Within 10 seconds per point
Note:1. Export Control
<For customers outside Japan>Murata products should not be used or sold for use in the development, production, stockpiling or utilization of any conventional weapons or mass-destructiveweapons (nuclear weapons, chemical or biological weapons, or missiles), or any other weapons.<For customers in Japan>For products which are controlled items subject to the “Foreign Exchange and Foreign Trade Law” of Japan, the export license specified by the law is requiredfor export.
2. Please contact our sales representatives or product engineers before using the products in this catalog for the applications listed below, which require especiallyhigh reliability for the prevention of defects which might directly damage to a third party's life, body or property, or when one of our products is intended for usein applications other than those specified in this catalog.q Aircraft equipment w Aerospace equipmente Undersea equipment r Power plant equipmentt Medical equipment y Transportation equipment (vehicles, trains, ships, etc.)u Traffic signal equipment i Disaster prevention / crime prevention equipmento Data-processing equipment !0 Application of similar complexity and/or reliability requirements to the applications listed in the above
3. Product specifications in this catalog are as of August 2005. They are subject to change or our products in it may be discontinued without advance notice.Please check with our sales representatives or product engineers before ordering. If there are any questions, please contact our sales representatives orproduct engineers.
4. Please read rating and CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
5. This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications ortransact the approval sheet for product specifications before ordering.
6. Please note that unless otherwise specified, we shall assume no responsibility whatsoever for any conflict or dispute that may occur in connection with the effectof our and/or a third party's intellectual property rights and other related rights in consideration of your use of our products and/or information described orcontained in our catalogs. In this connection, no representation shall be made to the effect that any third parties are authorized to use the rights mentionedabove under licenses without our consent.
7. No ozone depleting substances (ODS) under the Montreal Protocol are used in our manufacturing process.
International Division3-29-12, Shibuya, Shibuya-ku, Tokyo 150-0002, Japan Phone: 81-3-5469-6123 Fax: 81-3-5469-6155 E-mail: [email protected]
Head Office1-10-1, Higashi Kotari, Nagaokakyo-shi, Kyoto 617-8555, JapanPhone: 81-75-951-9111
http://www.murata.com/
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
S21E.pdf 05.11.16