Pw4000-100_opencowl Inspection Guide

FOR REFERENCE ONLY

PW4000 100-inch AIRBUSPW4000 100-inch AIRBUSOPEN COWL VISUAL INSPECTIONOPEN COWL VISUAL INSPECTION

For the prevention of Delays & Cancellations and IFSD’sFor the prevention of Delays & Cancellations and IFSD’s

September 2000September 2000

The information and instructions in this booklet are prepared for general informationpurposes only. The data contained herein shall not be considered in any way asreplacing or superceding the information contained in the PW4000 Turbofan EngineManual or Airbus A330 Maintenance Manual.

Prepared by:

Pratt & Whitney Customer Service -Line Maintenance & Troubleshooting

Pratt & Whitney Customer Training

© COPYRIGHT 2000UNITED TECHNOLOGIES CORPORATION

PW4000-100 AIRBUSPW4000-100 AIRBUS OPEN COWL INSPECTIONFOR THE PREVENTION OF DELAYS & CANCELLATIONS and IFSD’s

PW4000 OPEN COWL INSPECTION GUIDE

SUBJECT MATTER:

This reference guide covers the external visual inspection of the PW4000 series engine,including external components.

INTENDED FOR:

This reference guide is intended for maintenance personnel who are responsible forvisual inspections of the PW4000 engine. It is intended to be used in conjunction withclassroom instruction and as a stand alone learning resource during the PW4000 SystemFamiliarization course or the PW4000 Line and Base Maintenance training course.

LLEEFFTT SSIIDDEE

1. Inlet Area (CHECK):a. Inlet cowl for damage (including missing sealant) and evidence of birdstrike.b. Fan blades for damage.c. P2/T2 probe for damage or debris.d. Fan rub strip for heavy wear.e. Outer barrel for damage (including chipping paint on leading edge).

2. Fan Cowl / Thrust Reverser Actuation Area – Left (CHECK):a. Forward/aft fan cowl door for leading edge delamination/chipping paint.b. For open lock levers.c. For evidence of Skydrol leaks.d. All connectors for coupling nut and backshell tightness.e. Area harness clamps for chafing and general condition.f. Area harnesses for chafing or cuts.

3. Thrust Reverser Area – Left (CHECK):a. For thrust reverser firecoat/fireblanket damage.b. For evidence of thrust reverser interference..c. For transcowl screen delamination.d. For damage to transcowl or blocker doors.e. For upper and lower transcowl fairing cracks.

4. EEC / Engine Relay Unit (ERU) / Lower Birfurcation Conduit Area (CHECK):a. EEC pressure sense line fittings for tightness.b. ERU mounts for looseness or fractures.c. All connectors and EEC Programming Plug for coupling nut and backshell tightness.d. Area harness clamps for chafing and general condition.e. Area harnesses for chafing or cuts.

5. Fan Bypass Exit Area – Left (CHECK):a. Area for damage (fan blades, fan exit guide vanes and struts).

6. (2.5) Bleed Actuator Area (CHECK):a. Area for evidence of fuel/oil leakage.b. Area connectors for coupling nut and backshell tightness.c. Area tubes and harness clamps for chafing and general condition.d. Area harnesses for chafing or cuts.

7. (2.9) Bleed Solenoid / TVBC Air/Anti-Ice Valve Solenoid / (2.9) Stability Bleed Valve Area(CHECK):

a. Temperature probe connections for looseness, cracking or broken lugs on the 2.9 stabilitybleed valve.

b. Area for evidence of fuel/oil leakage.c. Area connectors for coupling nut and backshell tightness.d. Area tubes and harness clamps for chafing and general condition.e. Area harnesses for chafing or cuts.

8. Fuel/Oil Cooler & Bypass Valve Area (CHECK):a. Area for evidence of fuel/oil leakage.b. Area connectors for coupling nut and backshell tightness.c. Area tubes and harness clamps for chafing and general condition.d. Area harnesses for chafing or cuts.

9. Front Hydraulic Pump / PMA / Main Oil Filter Cover Area (CHECK):a. Main gearbox chip detector for proper installation and leakage.b. Oil filter cover for leakage.c. Area for evidence of fuel/oil leakage.d. Area connectors for coupling nut and backshell tightness.e. Area tubes and harness clamps for chafing and general condition.f. Area harnesses for chafing or cuts.

10. Oil Tank / HP Valve Area (CHECK):a. Oil quantity transmitter connector and other connectors for coupling nut and backshell

tightness.b. Oil tank cap and O-ring for damage.c. Oil level (per AMM section 12-13-79).d. Master chip detector for proper installation and leakage.e. T3 temperature probe for looseness, cracking or broken lugs.f. Area for evidence of oil leakage.g. Area tubes and harness clamps for chafing and general condition.h. Area harnesses for chafing or cuts.

11. IDG / Oil Pump Area (CHECK):a. Pump chip detectors for proper installation and leakage.b. Area for evidence of fuel/oil leakage.c. Area connectors for coupling nut and backshell tightness.d. Area tubes and harness clamps for chafing and general condition.e. Area harnesses for chafing or cuts.

12. HPT / LPT Case Area – Left (CHECK):a. Cooling manifolds for cracking.b. Area for evidence of oil leakage.c. Area connectors for coupling nut and backshell tightness.d. Area tubes and harness clamps for chafing and general condition.e. Area harnesses for chafing or cuts.

13. Exhaust Case Area – Left (CHECK):a. EGT probe connections for looseness, cracking and broken lugs.b. No.4 bearing scavenge tube for evidence of clamp migration, chafing or oil leakage.c. P4.95 system B-nuts for tightness.d. Area tubes and harness clamps for chafing and general condition.e. Area harnesses for chafing or cuts.

14. Exhaust Area (CHECK):a. Turbine blades for damage.b. Area for evidence of oil leakage.

PW4000-100 AIRBUSPW4000-100 AIRBUS OPEN COWL VISUAL INSPECTION CHECK LIST

RRIIGGHHTT SSIIDDEE

15. Exhaust Case Area – Right (CHECK):a. EGT probe connections for looseness, cracking or broken lugs.b. P4.95 system B-nuts for tightness.c. Area tubes and harness clamps for chafing and general condition.d. Area harnesses for chafing or cuts.

16. HPT / LPT Case Area – Right (CHECK):a. Cooling manifolds for cracking.b. Cooling valve linkage and arms for security.c. Area for evidence of oil leakage.d. Area tubes and harness clamps for chafing and general condition.e. Area harnesses for chafing or cuts.

17. Starter / Rear Hydraulic Pump / Igniter Box Area (CHECK):a. Area for evidence of fuel/oil leakage.b. Area connectors for coupling nut and backshell tightness.c. Area tubes and harness clamps for chafing and general condition.d. Area harnesses for chafing or cuts.

18. TCC Actuator / SVA Bellcrank Area (CHECK):a. 2.9 start bleed temperature probe connections for looseness, cracking or broken lugs.b. VSV system bolts, attaching adjustor rods to unison rings and bellcrank, for signs of wear.c. SVA bellcrank for excessive axial or radial movement.d. Area for evidence of fuel/oil leakage.e. Area connectors for coupling nut and backshell tightness.f. Area tubes and harness clamps for chafing and general condition.g. Area harnesses for chafing or cuts.

19. TVBC Air/Nacelle Cooling Valve / Starter Air Valve Solenoid Area (CHECK):a. Area for evidence of fuel/oil leakage.b. Area connectors for coupling nut and backshell tightness.c. Area tubes and harness clamps for chafing and general condition.d. Area harnesses for chafing or cuts.

20. IDG Air/Oil Heat Exchanger Area (CHECK):a. Area for evidence of fuel/oil leakage.b. Area connectors for coupling nut and backshell tightness.c. Area tubes and harness clamps for chafing and general condition.d. Area harnesses for chafing or cuts.

21. N1 Sensor Area (CHECK):a. Area for evidence of fuel/oil leakage.b. Area connectors for coupling nut and backshell tightness.c. Area tubes and harness clamps for chafing and general condition.d. Area harnesses for chafing or cuts.

22. VSV Actuator / FMU / Fuel Pump / Upper Bifurcation Conduit Area (CHECK):a. Fuel filter cover for leakage.b. Area for evidence of fuel leakage.c. Area connectors for coupling nut and backshell tightness.d. Area tubes and harness clamps for chafing and general condition.e. Area harnesses for chafing or cuts.

23. Fan Bypass Exit Area - Right (CHECK):a. Area for damage (fan blades, fan exit guide vanes and struts).

24. Thrust Reverser Area – Right (CHECK):a. For thrust reverser firecoat/fireblanket damage.b. For evidence of thrust reverser interference.c. For transcowl screen delamination.d. For damage to transcowl or blocker doors.e. For upper and lower transcowl fairing cracks.

25. Fan Cowl / Thrust Reverser Actuation Area – Right (CHECK):a. Forward/aft fan cowl door for leading edge delamination/chipping paint.b. For open lock levers.c. For evidence of Skydrol leaks.d. All connectors for coupling nut and backshell tightness.e. Area harness clamps for chafing and general condition.f. Area harnesses for chafing or cuts.

PW4000-100 AIRBUSPW4000-100 AIRBUS OPEN COWL VISUAL INSPECTION CHECK LIST

1. Inlet Area (CHECK):

a. Inlet cowl for damage (including missingsealant) and evidence of birdstrike.

b. Fan blades for damage.

c. P2/T2 probe for damage or debris.

d. Fan rub strip for heavy wear.

e. Outer barrel for damage (including chippingpaint on leading edge).

AMM 71-61-00, 71-61-41

This page intentionally left blank.

ENGINE LEFT SIDEENGINE LEFT SIDE

Feedback Actuator

Locking Actuator

2. Fan Cowl / Thrust Reverser ActuationArea - Left (CHECK):

a. Forward/aft fan cowl door for leading edgedelamination/chipping paint.

b. For open lock levers.

c. For evidence of Skydrol® leaks.

d. All connectors for coupling nut and backshelltightness.

e. Area harness clamps for chafing and generalcondition.

f. Area harnesses for chafing or cuts.

AMM 71-13-00, 78-30-00, 78-31-00

Thrust Reverser Door

Transcowl Blocker Doors

Transcowl Fairing

3. Thrust Reverser Area - Left (CHECK):

a. For transcowl screen delamination.

b. For damage to transcowl or blocker doors.

c. For upper and lower transcowl fairing cracks.

d. For thrust reverser firecoat/fireblanket damage.

e. For evidence of thrust reverser interference.

AMM 78-30-00

4. EEC / Engine Relay Unit (ERU) /Lower Bifurcation Conduit Area (CHECK):

a. EEC pressure sense line fittings for tightness.

b. EEC and ERU mounts for looseness orfractures.

c. All connectors and EEC Programming Plugfor coupling nut and backshell tightness.

d. Area tubes and harness clamps for chafingand general condition.

e. Area harnesses for chafing or cuts.

AMM 73-21-00

5. Fan Bypass Exit Area - Left (CHECK):

a. Area for damage (fan blades, fan exitguide vanes and struts).

AMM 72-33-12

Actuator

6. (2.5) Bleed Actuator Area (CHECK):

a. Area for evidence of fuel/oil leakage.

b. Area connectors for coupling nut andbackshell tightness.

c. Area tubes and harness clamps for chafingand general condition.

d. Area harnesses for chafing or cuts.

AMM 75-32-00

2.9 Bleed Valve Solenoid

TVBC Air SOV/Anti-Ice Valve Solenoid 2.9 Stability Bleed Valve Probe

7. (2.9) Bleed Solenoid /TVBC Air/Anti-Ice Valve Solenoid /

(2.9) Stability Bleed Valve Area (CHECK):

a. Temperature probe connections for looseness,cracking or broken lugs on the 2.9 stabilitybleed valve.

b. Area for evidence of fuel/oil leakage.

c. Area connectors for coupling nut and backshelltightness.

d. Area tubes and harness clamps for chafing andgeneral condition.

e. Area harnesses for chafing and cuts.

AMM 75-32-00

Fuel/Oil Cooler

Bypass Valve

8. Fuel/Oil Cooler & Bypass Valve Area(CHECK):


b. Area connectors for coupling nut and backshelltightness.

c. Area tubes and harness clamps for chafing andgeneral condition.


AMM 79-00-00

PMA

Hydraulic Pump Main Oil Filter

Main Chip Detector

9. Front Hydraulic Pump / PMA / Main Oil Filter /Upper Bifurcation Area (CHECK):

a. Main gearbox chip detector for proper installationand leakage.

b. Oil filter cover for leakage.

c. Area for evidence of fuel/oil leakage.

d. Area connectors for coupling nut and backshelltightness.

e. Area tubes and harness clamps for chafing andgeneral condition.

f. Area harnesses for chafing and cuts (includingforward hydraulic lines for gouging).

AMM 75-26-16, 79-00-00, 79-22-11

T3 Probe

Master Chip Detector

Oil Quantity Transmitter

HP Valve

10. Oil Tank Area / HP Valve Area (CHECK):

a. Oil quantity transmitter connector and other areaconnectors for coupling nut and backshell tightness.

b. Oil tank cap and O-ring for damage.

c. Oil level.

d. Master chip detector for proper installation and leakage.

e. T3 temperature probe connections for looseness,cracking or broken lugs.

f. Area for evidence of oil leakage.

g. Area tubes and harness clamps for chafing and generalcondition.

h. Area harnesses for chafing or cuts.

AMM 12-13-79, 79-00-00, 79-22-00

Oil PumpIDG

Chip Detectors

11. IDG / Oil Pump Area (CHECK):

a. Pump chip detectors for proper installation andleakage.

b. Area for evidence of fuel/oil leakage.




AMM 24-21-00, 79-22-11

12. HPT / LPT Case Area - Left (CHECK):

a. Cooling manifolds for cracking.

b. Area for evidence of oil leakage.




AMM 75-24-00

No. 4 Brg. Scavenge Tube P4.95 ‘B’ Nut

EGT Probes

13. Exhaust Case Area - Left (CHECK):

a. EGT probe connections for looseness, crackingor broken lugs.

b. No.4 bearing scavenge tube for evidence ofclamp migration, chafing or oil leakage.

c. P4.95 system B-nuts for tightness.



AMM 77-13-11, 77-21-11, 79-22-00

14. Exhaust Area (CHECK):

a. Turbine blades for damage.

b. Area for evidence of oil leakage.

AMM 78-11-00

This page intentionally left blank.

ENGINE RIGHT SIDEENGINE RIGHT SIDE

EGT Probes

P4.95 ‘B’ Nut

15. Exhaust Case Area - Right (CHECK):

a. EGT probe connections for looseness, crackingor broken lugs.

b. P4.95 system B-nuts for tightness.



AMM 77-13-11, 77-21-11

16. HPT/LPT Case Area - Right (CHECK):

a. Cooling manifolds for cracking.

b. Cooling valve linkage and arms for security.

c. Area for evidence of oil leakage.



AMM 75-24-00

Hydraulic Pump Igniter Box

Starter

17. Starter / Rear Hydraulic Pump /Igniter Area (CHECK):




d. Area harnesses for chafing and cuts.

AMM 74-00-00, 80-11-11

SVA Bellcrank

TCC Actuator

18. TCC Actuator / SVA Bellcrank Area (CHECK):

a. 2.9 start bleed temperature probe connections for looseness,cracking or broken lugs.

b. VSV system bolts, attaching adjustor rods to unsion ringsand bellcrank, for signs of wear.

c. SVA bellcrank for excessive axial or radial movement.

d. Area for evidence of fuel/oil leakage.

e. Area connectors for coupling nut and backshell tightness.

f. Area tubes and harness clamps for chafing and generalcondition.

g. Area harnesses for chafing and cuts.

AMM 75-24-00, 75-31-00

TVBC Air/NacelleCooling Valve Solenoid

Starter Air Valve Solenoid

19. TVBC Air/Nacelle Cooling Valve /Starter Air Valve Solenoid Area (CHECK):





AMM 75-25-00

20. IDG Air/Oil Heat Exchanger Area (CHECK):





AMM 24-21-00

21. N1 Sensor (CHECK):





VSV Actuator

FMUFuel Pump

22. VSV Acuator / FMU / Fuel Pump /Upper Bifurcation Conduit Area (CHECK):

a. Fuel filter cover for leakage.

b. Area for evidence of fuel leakage.



e. Area harnesses for chafing and cuts.

AMM 73-00-00, 75-31-00

23. Fan Bypass Area - Right (CHECK):

a. Area for damage (fan blades, fan exitguide vanes and struts).

AMM 72-32-12

Thrust Reverser Door

Transcowl Blocker Doors

Transcowl Fairing

24. Thrust Reverser Area - Right (CHECK):

a. For transcowl screen delamination.

b. For damage to transcowl or blocker doors.

c. For upper and lower transcowl fairing cracks.

d. For thrust reverser firecoat/fireblanket damage.

e. For evidence of thrust reverser interference.

AMM 78-30-00

Feedback Actuator

Directional Control Valve

Locking Actuator

25. Fan Cowl / Thrust Reverser ActuationArea - Right (CHECK):

a. Forward/aft fan cowl door for leading edgedelamination/chipping paint.

b. For open lock levers.

c. For evidence of Skydrol® leaks.

d. All connectors for coupling nut and backshelltightness.

e. Area harness clamps for chafing and generalcondition.

f. Area harnesses for chafing or cuts.

AMM 71-13-00, 78-30-00, 78-31-00

TRAINING MATERIALS CHANGE REQUEST Date: __________________________

Company Name and Address: _______________________________________________________________________

Your Name: __________________________________ Job Title: ___________________________________

Training Aid Title: __________________________________________________________________________________

Reference Page(s): ________________________________________________________________________________

Recommended Change(s) and Reason(s) for Change(s): __________________________________________________

________________________________________________________________________________________________

________________________________________________________________________________________________

________________________________________________________________________________________________

________________________________________________________________________________________________

________________________________________________________________________________________________

________________________________________________________________________________________________

TMCR ID Number (P&W Office Use Only): ______________________________________________________________

Send To: Note: If you would like to be contacted regardingPratt & Whitney Customer Training Center the resolution of your request for change, please400 Main Street, M/S 122-18 provide us with your telefax number:East Hartford, CT 06108

Telefax Number: _________________________

400 MAIN STREET, EAST HARTFORD, CONNECTICUT 06108 U.S.A.

Printed in U.S.A.

Documents

Pw4000-100_opencowl Inspection Guide