Publications No. INSTALLATION HATCH TENT KIT 201 CR-V

Publications No.

Issue DateINSTALLATIONINSTRUCTIONS

Accessory Application

© 2015 American Honda Motor Co., Inc. – All Rights Re

VERSION 1

Put this inf

HATCH TENT KIT

served. AII02406-18 (

ormation in the glove box w

2016 CR-V

1509)

ith the vehicle owner’s manu

SEP 2015

al

PARTS LIST

Tent bag

Tent

2 Tie straps

Rain cover

Pole bag

2 Tent poles

2 Awning poles

Stake bag

13 Stakes

4 Guide ropes

2 Awning pole caps

Gear loft

USE AND CARE

CAUTION:

• Never smoke inside the tent. Never use candles, light matches or allow any type of open flame in or near the tent.

• Do not cook inside the tent.

• Do not store flammable liquids inside the tent.

• Allow adequate ventilation inside the tent at all times.

• Never run the engine when the tent is attached to the vehicle.

WARNING:

Keep all flame and heat sources away from this tent fabric. This tent is made with flame-resistant fabric which meets CPAI-84 specifications. It is not fireproof. The fabric will burn if left in continuous contact with any flame source. The application of any foreign substance to the tent fabric may render the flame-resistant properties ineffective.

1 of 708Z04-SCV-1B00-91

INSTALLATION

Attaching the Tent to the VehicleNOTE: • Leaving the tailgate open for an extended amount of

time will drain the battery.• Allow the exhaust pipe to cool down for at least 20

minutes before you attach the tent to the vehicle.• The tent is designed to add additional space to your

vehicle while parked. It is not intended to be used when the vehicle is moving.

• The tent can also be used as a standard ground tent by zipping up the rear sock.

• If the tent is not going to be attached to the vehicle, assemble the tent as described, but move it away from the vehicle.

• Make sure the vehicle and tent are clean and completely dry before installation. If moisture under the tent is allowed to dry, it may cloud the paint. If the tent gets wet, remove it and allow it to air-dry completely.

1. Park the vehicle on smooth level ground, with the transmission in Park (auto transmission), or neutral (manual transmission). Apply the parking brake.

2. Remove the tent from the tent bag, and lay it flat on the ground with the straps facing the rear of the vehicle, and the “H” emblem away from the vehicle. Do not stake the tent at this time.

1.5 m (5 ft)

TENT

“H” EMBLEM

2 of 7 AII02406-

3. Unfold the tent poles (11 segments each) and assemble them into one long pole. Assemble the other connected tent pole the same way.

4. Slide each connected pole through the sleeves in the roof of the tent.

860303BH

2 TENT POLES

860305BH

TENT

TENT POLE

TENT POLE

18 (1509) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.

5. With the help of an assistant, set-up the tent: • Starting at any corner, insert the corner tent pin

into the bottom of the tent pole.

• At the opposite corner of the tent, walk towards the tent while you flex the tent pole and stand up the center of the tent. Insert the tent corner pin into the bottom of the tent pole.

• Repeat this procedure to stand up the remaining tent pole.

860306AH

TENT

TENT POLE

TENT PIN

860307AH

TENT

TENT POLE

TENT PIN

© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII0240

• When the tent is standing, attach the plastic clips at each corner around the tent poles.

6. Move the tent towards the rear of the vehicle. Slip the sock over the roof and the around the sides of the vehicle. The magnetic strips will hold the sock to the vehicle. Install the magnetic strips carefully because the magnets are very strong.

860308AHTENT

TENT POLE

PLASTIC CLIPS

MAGNETIC STRIPS

SOCK

TENT

6-18 (1509) 3 of 7

7. From inside the tent, unzip the rear door and rear screen that face the vehicle. Roll up the screen and the door material, and secure them to the tent with the sewn-in T-straps.

8. Stretch the bottom elastic strap across the rear face of the bumper. Make sure the tent material is tight against the rear face of the bumper, with the exhaust pipe outside the tent. Go outside of the tent, and make sure the exhaust pipe is outside.

WARNING

• Exhaust contains poisonous carbon monoxide gas that can build up to dangerous levels in enclosed areas.

• Breathing carbon monoxide can cause unconsciousness or death.

• Never start or run the vehicle’s engine when the tent is attached to the vehicle.

T-STRAPS

SCREEN AND DOOR MATERIAL

860311AHTENT EXHAUST

PIPE

4 of 7 AII02406-

9. Attach the outside straps to the rear fenderwell, then tighten the straps.NOTE: If the vehicle is equipped with splash guards, install the lower straps to the edge of the splash guards.

REAR FENDERWELL

STRAPS


10. Along the roof of the vehicle, attach the straps to the roof rack (if equipped), or extend the long straps forward and attach the hooks to the hood hinge or hood frame. Tighten the straps to secure the tent.

With Roof Rack (Side Rail Type Only)

Without Roof Rack

STRAPS

ROOF RACK SIDE RAIL

LONG STRAPS

STRAPS

HOOD

HOOK

HOOD HINGES

HOOK

HOOKSHOOD

Both straps can be hooked in one hole.

WHEN THE HOOKS CANNOT BE INSTALLED TO THE HOOD HINGE


When Using the Hatch Tent with the Tailgate Open

NOTE: Leaving the tailgate open for an extended amount of time will drain the battery.11. Inside the tent, attach the two outer S-hooks from the

tent to the tailgate latches, or to the cargo tie-down hooks inside the vehicle. Attach the center S-hook to the tailgate latch hook.

860315AH

S-HOOKS-HOOK

CARGOTIE-DOWNHOOK

WITHOUT TAILGATE LATCH

S-HOOK

TAILGATE LATCH

HOOPCARGO TIE-DOWN HOOK

TAILGATE LATCH HOOK

S-HOOK

6-18 (1509) 5 of 7

12. At each of the four corners, stake the tent down with one tent stake through the tab.

13. Drape the rain cover over the tent, and position the awning portion over the front door opening.

860316BH

STAKE

TAB

860317AH

FRONT

RAIN COVER

TENT

6 of 7 AII02406-

14. Attach the hook on each corner of the rain cover to each loop on the tent. Wrap the hook-and-loop tabs around each pole to hold the rain cover in place.

15. Assemble the two awning poles.

860318BH

RAIN COVER

TENT

TENT RING

HOOK

TENT POLE

HOOK-AND-LOOP TAB

860304BH

AWNING POLE


16. With the help of an assistant, place the tip of one awning pole through the grommet at the corner of the awning. Insert the ring of the guide rope around the tip of the awning pole, and stake the other end to the ground using one stake.

17. Pull the awning tight, adjust the height of the awning using the telescopic pole, and secure the awning to the ground using an additional stake and guide rope. Secure the other pole using the same procedure. If necessary, adjust the guide rope length using the adjuster on the rope.

860319BH

GROMMETS

RINGS

STAKES

AWNING POLES

AWNING

AWNING POLE CAPS

GUIDE ROPE


18. Inside the tent, install the four hooks on the gear loft to the four hoops on the tent.

860501AH

4 HOOPS

GEAR LOFT4 HOOKS

6-18 (1509) 7 of 7

Publications No.




AII 43482

Put this inform

HATCH TENT KIT

served. AII 43482 (1010

ation in the glove box w

2011 ELEMENT

)

ith the vehicle owner’s

OCT 2010

manual

PARTS LIST

Tent bag

Tent

2 Tie straps

Rain cover

Pole bag

2 Tent poles

2 Awning poles

Stake bag

13 Stakes

4 Guide ropes

2 Awning pole caps

Gear loft

USE AND CARE

CAUTION:

• Never smoke inside the tent. Never use candles, light matches or allow any type of open flame in or near the tent.




• Never run the engine when the tent is attached to the vehicle.

WARNING:

Keep all flame and heat sources away from this tent fabric. This tent is made with flame-resistant fabric which meets CPAI-84 specifications. It is not fireproof. The fabric will burn if left in continuous contact with any flame source. The application of any foreign substance to the tent fabric may render the flame-resistant properties ineffective.

1 of 708Z04-SCV-1B00-91

INSTALLATION

Attaching the Tent to the Vehicle

NOTE: • Leaving the tailgate open for an extended amount of

time will drain the battery.• Allow the exhaust pipe to cool down for at least 20

minutes before you attach the tent to the vehicle.• The tent is designed to add additional space to your

vehicle while parked. It is not intended to be used when the vehicle is moving.

• The tent can also be used as a standard ground tent by simply zipping up the rear sock.

• If the tent is not going to be attached to the vehicle, assemble the tent as described, but move it away from the vehicle.

• Make sure the vehicle and tent are clean and completely dry before installation. If moisture under the tent is allowed to dry, it may cloud the paint. If the tent gets wet, remove it and allow it to air-dry completely.

1. Park the vehicle on smooth level ground, with the transmission in Park (auto transmission), or neutral (manual transmission). Apply the parking brake.

2. Remove the tent from the tent bag, and lay it flat on the ground with the straps facing the rear of the vehicle, and “H” emblem away from the vehicle. Do not stake the tent at this time.

860302BH

1.5 m (5 ft)

“H” EMBLEM

TENT

2 of 7 AII 43482

3. Unfold the tent poles (11 segments each) and assemble them into one long pole. Assemble the other connected tent pole the same way.

4. Slide each connected pole through the sleeves in the roof of the tent.

860303BH

2 TENT POLES

860305BH

TENT

TENT POLE

TENT POLE

(1010) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.

5. With the help of an assistant, set-up the tent: • Starting at any corner, insert the corner tent pin

into the bottom of the tent pole.

• At the opposite corner of the tent, walk towards the tent while you flex the tent pole and stand up the center of the tent. Insert the tent corner pin into the bottom of the tent pole.

• Repeat this procedure to stand up the remaining tent pole.

860306AH

TENT

TENT POLE

TENT PIN

860307AH

TENT

TENT POLE

TENT PIN

© 2010 American Honda Motor Co., Inc. – All Rights Reserved. AII 43482

• When the tent is standing, attach the plastic clips at each corner around the tent poles.

6. Move the tent towards the rear of the vehicle. Slip the sock over the roof and the around the sides of the vehicle. The magnetic strips will hold the sock to the vehicle. Install the magnetic strips carefully because the magnets are very strong.

860308AHTENT

TENT POLE

PLASTIC CLIPS

860309BH

SOCKMAGNETIC STRIPS

TENT

(1010) 3 of 7

7. From inside the tent, unzip the rear door and rear screen that face the vehicle. Roll up the screen and the door material, and secure them to the tent with the sewn-in T-straps.

8. Stretch the bottom elastic strap across the rear face of the bumper. Make sure the tent material is tight against the rear face of the bumper, with the exhaust pipe outside the tent. Go outside of the tent, and make sure the exhaust pipe is outside.

WARNING

• Exhaust contains poisonous carbon monoxide gas that can build up to dangerous levels in enclosed areas.Breathing carbon monoxide can cause unconsciousness or death.

• Never start or run the vehicle’s engine when the tent is attached to the vehicle.

860310BHT-STRAPS

SCREEN AND DOOR MATERIAL

860311AHTENT EXHAUST

PIPE

4 of 7 AII 43482

9. Attach the outside straps to the rear fenderwell, then tighten the straps.NOTE: If the vehicle is equipped with splash guards, install the lower straps to the edge of the splash guards.

860312AH

STRAPS

REAR FENDERWELL


10. Along the roof of the vehicle, attach the straps to the roof rack (if equipped), or extend the long straps forward and attach the hooks to the hood hinge or hood frame. Tighten the straps to secure the tent.


Without Roof Rack

860313AH

STRAPS

ROOF RACK SIDE RAIL

860314CH

STRAPS

LONG STRAPS

HOODHOOKS

Both straps can be hooked in one hole.

WHEN THE HOOKS CANNOT BE INSTALLED TO THE HOOD HINGE

HOOK

HOOKHOOD

HOOD HINGES



NOTE: Leaving the tailgate open for an extended amount of time will drain the battery.

11. Inside the tent, attach the two outer S-hooks from the tent to the tailgate latches, or to the cargo tie-down hooks inside the vehicle. Attach the center S-hook to the tailgate latch hook.

860315AH

S-HOOKS-HOOK

CARGOTIE-DOWNHOOK


S-HOOK

TAILGATE LATCH

HOOPCARGO TIE-DOWN HOOK

TAILGATE LATCH HOOK

S-HOOK

(1010) 5 of 7

12. At each of the four corners, stake the tent down with one tent stake through the tab.

13. Drape the rain cover over the tent, and position the awning portion over the front door opening.

860316BH

STAKE

TAB

860317AH

FRONT

RAIN COVER

TENT

6 of 7 AII 43482

14. Attach the hook on each corner of the rain cover to each loop on the tent. Wrap the hook-and-loop tabs around each pole to hold the rain cover in place.


860318BH

RAIN COVER

TENT

TENT RING

HOOK

TENT POLE

HOOK-AND-LOOP TAB

860304BH

AWNING POLE


16. With the help of an assistant, place the tip of one awning pole through the grommet at the corner of the awning. Insert the ring of the guide rope around the tip of the awning pole, and stake the other end to the ground using one stake.

17. Pull the awning tight, adjust the height of the awning using the telescopic pole, and secure the awning to the ground using an additional stake and guide rope. Secure the other pole using the same procedure. If necessary, adjust the guide rope length using the adjuster on the rope.

860319BH

GROMMETS

RINGS

STAKES

AWNING POLES

AWNING

AWNING POLE CAPS

GUIDE ROPE


18. Inside the tent, install the four hooks on the gear loft to the four hoops on the tent.

860501AH

4 HOOPS

GEAR LOFT4 HOOKS

(1010) 7 of 7

Publications No.

INSTALLATIONINSTRUCTIONS



VERSION 1

Put this inf

HATCH TENT KIT

served. AII02125-16 (150

ormation in the glove box w

2016 ODYSSEY

7) 0

ith the vehicle owner’s manu

Issue Date

JULY 2015

al

PARTS LIST

Tent bag

Tent

2 Tie straps

Rain cover

Pole bag

2 Tent poles

2 Awning poles

Stake bag

13 Stakes

4 Guide ropes

2 Awning pole caps

Gear loft

USE AND CARE

CAUTION:

• Never smoke inside the tent. Never use candles, lightmatches, or allow any type of open flame in or near thetent.




• Never run the engine when the tent is attached to thevehicle.

WARNING:

Keep all flame and heat sources away from this tentfabric. This tent is made with flame-resistant fabricwhich meets CPAI-84 specifications. It is not fireproof.The fabric will burn if left in continuous contact with anyflame source. The application of any foreign substanceto the tent fabric may render the flame-resistantproperties ineffective.

1 of 88Z04-SCV-1B00-91

INSTALLATION

NOTE:

• Leaving the tailgate open for an extended time will drainthe battery.

• Allow the exhaust pipe to cool down for at least 20minutes before you attach the tent to the vehicle.

• The tent is designed to add additional space to yourvehicle while parked. It is not intended to be used whenthe vehicle is moving.

• The tent can also be used as a standard ground tent byzipping up the rear sock.

• If the tent is not going to be attached to the vehicle,assemble the tent as described, but move it away fromthe vehicle.

• Make sure the vehicle and tent are clean andcompletely dry before installation. If moisture under thetent is allowed to dry, it may cloud the paint. If the tentgets wet, remove it and allow it to air-dry completely.

1. Park the vehicle on smooth level ground, with thetransmission in park. Apply the parking brake.

2. With the tent approximately 5 feet away from the rearof the vehicle, prepare the tent.

• Remove the tent from the tent bag, and lay it flaton the ground with the straps facing the rear ofthe vehicle, and “H” emblem away from thevehicle. Do not stake the tent at this time.

860302BH

1.5 m (5 ft)

“H” EMBLEM

TENT

2 of 8 AII02125-1

• Unfold the two tent poles (11 segments each)and assemble each of the connected sectionsinto one long pole.

• Slide each connected pole through the sleevesin the roof of the tent.

860303BH

2 TENTPOLES

860305BH

TENT

TENTPOLE

TENTPOLE


3. With the help of an assistant, setup the tent:

• Starting at any corner, insert the corner tent pininto the bottom of the tent pole.

• At the opposite corner of the tent, walk towardsthe tent while you flex the tent pole and stand upthe center of the tent. Insert the tent corner pininto the bottom of the tent pole.

• Repeat this procedure to setup the remainingtent pole.

860306AH

TENT

TENTPOLE

TENTPIN

860307AH

TENT

TENTPOLE

TENTPIN

© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02125-1

• When the tent is standing, attach the plastic clipsat each corner around the tent poles.

860308AHTENT

TENTPOLE

PLASTICCLIPS

6 (1507) 3 of 8

4. Move the tent towards the rear of the vehicle. Slip thesock over the roof and the around the sides of thevehicle. The magnetic strips will hold the sock to thevehicle. Install the magnetic strips carefully becausethe magnets are very strong.

5. Inside the tent, unzip the rear door and rear screenthat face the vehicle. Roll up the screen and thedoor material, and secure them to the tent with thesewn-in T-straps.

860309BH

SOCKMAGNETICSTRIPS

TENT

860310BHT-STRAPS

SCREEN ANDDOOR MATERIAL

4 of 8 AII02125-1

6. Stretch the bottom elastic strap across the rear faceof the bumper. Make sure the tent material is tightagainst the rear face of the bumper, with the exhaustpipe outside the tent. Go outside of the tent, andvisually inspect the location of the exhaust pipe toverify its location.

WARNING

• Exhaust contains poisonous carbon monoxidegas that can build up to dangerous levels inenclosed areas.Breathing carbon monoxide can causeunconsciousness or death.

• Never start or run the vehicle’s engine whenthe tent is attached to the vehicle.

860311AHTENT

EXHAUSTPIPE


7. Attach the outside straps to the rear fenderwell, thentighten the straps. If the vehicle is equipped withsplash guards, install the lower straps to the edge ofthe splash guards.

8. Attach the straps to the roof rack (if equipped), orextend the long straps forward and attach the hooksto the hood hinge or hood frame. Tighten the strapsto secure the tent.

860312AH

STRAPS

REARFENDERWELL



Without Roof Rack

860313AH

STRAPS

ROOFRACKSIDE RAIL

860314CH

STRAPS

LONGSTRAPS

HOOD

HOOKS

It is also OKto attachboth strapsin on e hole.

HOOK

HOOK

HOOD

HOODHINGES

6 (1507) 5 of 8


NOTE: Leaving the tailgate open for an extended time willdrain the battery.

9. Inside the tent, attach the two outer S-hooks from thetent to the tailgate latches, or to the cargo tie-downhooks inside the vehicle. Attach the center S-hook tothe tailgate latch hook.

860315AH

S-HOOKS-HOOK

CARGOTIE-DOWNHOOK


S-HOOK

TAILGATELATCH

HOOP

CARGOTIE-DOWNHOOK

TAILGATELATCH HOOK

S-HOOK

6 of 8 AII02125-1

10. At each of the four corners, stake the tent down withone tent stake through the tab.

11. Drape the rain cover over the tent, and position theawning portion over the front door opening.

860316BH

STAKE

TAB

860317AH

FRONT

RAINCOVER

TENT


12. Attach the hook on each corner of the rain cover toeach loop on the tent. Wrap the Velcro tabs aroundeach pole to hold the rain cover in place.


860318BH

RAINCOVER

TENT

TENTRING

HOOK

TENT POLE

HOOK-AND-LOOP TAB

860304BH

AWNINGPOLE


14. With the help of an assistant, place the tip of oneawning pole through the grommet at the corner of theawning. Insert the ring on the guide rope around thetip of the awning pole, and stake the other end to theground using one stake.

15. Pull the awning tight, adjust the height of the awningusing the telescopic pole, and secure the awning tothe ground using an additional stake and guide rope.Secure the other pole using the same procedure. Ifnecessary, adjust the guide rope length using theadjuster on the rope. Install the pole caps on the tipsof the awning poles.

860319BH

GROMMETS

RINGS

STAKES

AWNINGPOLES

AWNING

AWNINGPOLECAPS

GUIDEROPE

6 (1507) 7 of 8

16. Install the four hooks on the gear loft to the four loopson the tent.

860501AH

4 LOOPS

GEAR LOFT4 HOOKS

8 of 8 AII02125-1

Publications No.



© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII 01913-35 (1506) 1 of 708L07-E09-1000-91

UDQRHNM 0BICYCLE ATTACHMENT

(ROOF) P/N 08L07-E09-100

2016 PILOT

JUN 2015

PARTS LIST

Bicycle attachment

Hex wrench

2 Keys

2 Wheel straps

2 Tire adapters

2 End caps

4 Bolts

6 Washers

2 Brackets

4 Knobs

1 Rear Bracket Assy

2 of 7 AII 01913-35 (1506) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.

Illustration of the Bicycle Attachment on the Vehicle

INSTALLATION

NOTE:• This bicycle attachment is designed to be used

exclusively with the crossbars, which are soldseparately.

• Do not use non-Honda accessories, carriers orattachment sets with this bicycle attachment kit.

• Install the bicycle attachment after installing thecrossbars on the roof rack.

• Do not damage the roof and other finished surfaces ofthe body when installing this bicycle attachment.

• If you are installing more than one bicycle attachment,you may need to alternate the mounting positions (frontto rear) to allow for handle bar clearance.

• Make sure the tire adapters and the locking clamp lever are installed on the outboard side. See the instructionsheet for details.

Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”

7D0603AY

BICYCLE ATTACHMENT

Installing the Bicycle Attachment

1. Remove the two thumbwheel screws, washers, andbracket. Slide the rear bracket assembly onto thebicycle attachment.

BICYCLE ATTACHMENT

2 THUMBWHEEL SCREWS AND WASHERS

BRACKET

WASHER

© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII 01913-35 (1506) 3 of 7

2. Insert the wheel strap into the tire adapter, then slidethe wheel strap onto the end of the bicycleattachment. Repeat this on the other end of theattachment. Make sure that both wheel strap buckles are facing the same direction. Insert the four boltsinto the front plate.

BICYCLE ATTACHMENT

TIRE ADAPTER

WHEEL STRAP

TIRE ADAPTER

WHEEL STRAP

WHEEL STRAP

TIRE ADAPTER

BOLTS

3. Install the end caps onto the bicycle attachment byaligning the lock tab on the end cap with the hole inthe bicycle attachment. Push on the end cap until thelock tab “clicks” into place.

700903AX

BICYCLE ATTACHMENT

BICYCLE ATTACHMENT

END CAP

HOLE LOCK TAB

END CAP

END CAP


4. Install the bicycle attachment to the crossbar withtwo thumbwheel screws and one bracket. Repeatthis to install brackets at the other two positions onthe bicycle attachment.

BICYCLE ATTACHMENT

CROSS BARS

BICYCLE ATTACHMENT

THUMBWHEEL SCREWS AND WASHERS

BRACKET

CROSS BAR

WASHER

5. Close the locking clamp lever. To deter theft of thebicycle attachment, lock the locking clamp lever withthe key.

700905AX

BICYCLE ATTACHMENT

LOCKING CLAMP LEVER

KEY


6. Write down the key number in case the key is lost orstolen.

7. Store the key in the glove box for future use.

How to Install the Bicycle on the Bicycle Attachment

8. Do not carry a bicycle with this bicycle attachment ifthe diameter of its frame exceeds 55 mm or if itssectional view is not circular in the area where it isheld by the bicycle holder.

KEY

700906AX

55 mm or below BICYCLE

FRAME

BICYCLE HOLDER

9. Release the locking clamp lever with the key and pull the locking clamp lever down.

700907AX

LOCKING CLAMP LEVER

KEY

Turn.


10. Position the bicycle on the channel. Lift the arm up,and clamp the holder around the bicycle’s frame bypushing down the slider.

11. Push up the locking clamp lever to secure the bicycle frame.

700908AX

BICYCLE ATTACHMENT

BICYCLE FRAME

BICYCLE

LOCKING CLAMP LEVER

BICYCLE HOLDER

CHANNEL

Push down.

ARM

SLIDER

12. Lock the locking clamp lever by inserting the key intothe key cylinder and turning it in a clockwisedirection.

13. Position the wheel straps at the centers of thebicycle’s wheels, then secure the wheels with thewheel straps by inserting the belts through thebuckles and locking the buckles in the directionshown. If the size of the bicycle tire is too big to besecured by the belts, reinstall the tire adaptersupside down on the belts as shown. Make sure thebuckles are latched securely.

700909AX

LOCKING CLAMP LEVER

KEY

Turn.

700910AX

WHEEL STRAPWHEEL STRAP

WHEEL STRAP

WHEEL STRAP

BUCKLE BUCKLE

TIRE ADAPTER

TIRE ADAPTER


USE AND CARE• Addition of the bicycle attachment on the vehicle raises

the overall height of the vehicle. Pay attention to overhead obstacles when driving with the bicycle attachment.

• Before and after driving, or after loading the bicycle onthe attachment, check the security of the attachmentmounts and retighten them as necessary.

PRECAUTION• Avoid sudden starts or stops with the attachment on the

vehicle. It may cause bolts and other fasteners to loosen.

• Obey local laws and regulations.• Before driving, check that the attachment is locked

securely regardless of whether or not a bicycle ismounted on the attachment.

• Do not use the bicycle attachment with vehicles otherthan those specified.

Documents

Publications No. INSTALLATION HATCH TENT KIT 201 CR-V