brands you trust.

PROSSER STANDARD-LINE®

Submersible DewateringProsser VersatilityIf you need to remove unwanted water, a Prosser portable electric submersible pump is your solution. Prosser Standard-Line® pumps offer high head or high volume performance and are available in over 130 outstanding models. You can also include optional features such as watertight control enclosures, liquid level controls, adapter kits, and more. This wide range of choices enables you to select the exact pump you need to fit your application.

Heads to 210’Flows to 1400GPM¾ - 50 HPDischarge Sizes 2" - 6"Slim Line Design

Prosser Standard-Line®

Built Rugged for DependabilityWherever unwanted water is found, Prosser Standard-Line® submersible pumps are the most cost-effective choice for efficient, reliable dewatering. Prosser pumps have proven their value with dependable performance in a variety of challenging applications including:

• Construction• Industrial• Marine• Utilities• Telecommunication• Municipal• Government

Performance You Can Count OnBenefits:• Pumps require no

priming, suction hose, or foot valve. Just submerge them and they are ready to go.

• Operate in any position.

• Bearings require no outside lubrication.

• Unique in-line design ensures a cool-running motor by transferring motor heat directly to the pumped fluid.

• Abrasion resistant impellers and silicon carbide outboard shaft seals help ensure trouble-free performance.

Prosser Standard-Line® Products & Accessories

2

Selection Chart (60Hz):

Discharge Size HP Head

in FeetFlow

(U.S. GPM)

Max.Pump

DiameterLength Weight

(Pump Only)Suction

ConnectionDischarge

Connection

2"

¾(a)

5152535

98805727

5½"(140 mm)

15.74"(400 mm)

23 lbs(10.4 Kgs) 1½" 9 NHT 2" NPT (F)

1(a)

10203540

107833820

5½"(140 mm)

15.74"(400 mm)

23 lbs(10.4 Kgs) 1½" 9 NHT 2" NPT (F)

2(b)

25425568

120805020

7"(188 mm)

18"(457 mm)

50 lbs(23 Kgs) 3" Vict (M) 2" & 3" NPT (F)

2½ HH(c)

30506578

1401007530

7"(188 mm)

18"(457 mm)

50 lbs(23 Kgs) 3" Vict (M) 2" & 3" NPT (F)

2½ HV(c)

10203045

29023016050

7"(188 mm)

18"(457 mm)

50 lbs(23 Kgs) 3" Vict (M) 2" & 3" NPT (F)

5 HH(c)

65105125145

1501007550

7"(188 mm)

24"(609 mm)

65 lbs(30 Kgs) 3" Vict (M) 2" & 3" NPT (F)

3"

2¾(b)

10203045

29023016050

7"(188 mm)

18"(457 mm)

50 lbs(23 Kgs) 3" Vict (M) 2" & 3" NPT (F)

3½(b)

20406070

25017510050

7"(188 mm)

22"(559 mm)

65 lbs(30 Kgs) 3" Vict (M) 3" NPT (F)

5 HV(c)

30557085

30020012550

7"(188 mm)

22"(559 mm)

65 lbs(30 Kgs) 3" Vict (M) 3" NPT (F)

4"

10 HV(c)

206080

100

600400300100

10½"( 267 mm)

29"(737 mm)

150 lbs(68 Kgs) 5" Vict (M) 4" NPT (F)

10 HH(c)

2065

102140

450300200100

10½"( 267 mm)

29"(737 mm)

150 lbs(68 Kgs) 5" Vict (M) 4" NPT (F)

15 HV(c)

305087

120

800600400200

10½"( 267 mm)

41"(787 mm)

155 lbs(70 Kgs) 5" Vict (M) 4" NPT (F)

15 HH(c)

2060

120180

550450300100

10½"( 267 mm)

41"(787 mm)

155 lbs(70 Kgs) 5" Vict (M) 4" NPT (F)

6"

25 HV(c)

5090

120150

1000750500200

12¾"(327 mm)

37"(940 mm)

275 lbs(125 Kgs) 6" Vict (M) 6" NPT (F)

25 HH(c)

50105160200

800600400200

12¾"(327 mm)

37"(940 mm)

275 lbs(125 Kgs) 6" Vict (M) 6" NPT (F)

50 HV(c)

50100140160

14001100750500

12¾"(327 mm)

37"(940 mm)

343 lbs(156 Kgs) 6" Vict (M) 6" NPT (F)

50 HH(c)

80150180210

1000600450250

12¾"(327 mm)

37"(940 mm)

343 lbs(156 Kgs) 6" Vict (M) 6" NPT (F)

HV = High Volume HH = High Head Available in (a) 1 & 3 phase, (b) 1 phase, or (c) 3 phase

Prosser Pump Control and AccessoriesPump Control Panels

• Equipped with a special circuit breaker that provides protection against short circuit, overload, and locked rotor by disconnecting power to the pump if any of these conditions occur. The circuit breaker also serves as a manual across-the-line motor control.

• Includes a reset button to start pumping once conditions have been corrected.• Offered with standard length cable (other lengths available).• Optional rainproof (NEMA 3R) or watertight (NEMA 4) corrosion-resistant enclosures available.

Galvanic Protection Kit• Protects pump against corrosion caused by electrolytic action.

Sludge and Mushroom Strainer• Designed to raise the pump's suction screen above sludge in a manhole or pit.• Removes water with a top-down pumping action to a level of 6" - 8" from the bottom• Fits all Prosser Standard-Line® pumps to ¾ - 5HP.

• Mushroom strainer will allow water removal to within .25" of floor level (2" Discharge Units).• Easily assembled and disassembled.

3

1

2

13

3

4

5

8

9

14

7

16

17

19

10

1. Type SO or Type G power cable with cable strain relief on all pumps for maximum cable and connection protection.

2. Eyebolt on ¾ and 1 HP (Two lifting lugs on center line or larger units).

3. Hardware is stainless steel (¾ and 1 HP only) or zinc-plated to resist erosion, corrosion and wear.

4. Buna "N" O-ring static seals.5. Motor construction with silicon steel laminations,

die-cast aluminum rotors and copper magnet wire. Also utilizes a Class B (¾ and 1 HP) and Class F (2 - 50 HP) insulation system.

6. Anti-corrosion treated wetted surfaces.7. Stainless steel shaft resists corrosion.8. Oil chamber for seal lubrication.9. Suction case made of 356T6 Aluminum,

anti-corrosion coated, plus wear-resistant polyurethane liner.

10. Rugged suction strainer is stainless steel. 11. Water-tight connection box (not shown).12. Pressure test plug to check integrity of pump

seals (not shown).13. 356T6 Aluminum, anti-corrosion coated

discharge head.14. Permanently lubricated radial bearings.15. Special abrasion resistant wear plate on 2 - 5

HP models protects the diffuser from abrasive material (not shown).

16. Permanently lubricated thrust bearings.17. Inboard ceramic and carbon shaft seal with Buna

"N" elastomers.18. Outboard Prosser-designed silicon carbide shaft

seal with Viton® elastomers for durability and wear resistance (not shown).

19. Polyurethane impellers with stainless steel option on ¾ - 1 HP units. Abrasive-resistant impellers of hardened 17-4 stainless steel (40-44 Rockwell) on 2 HP and larger models.

Series Operation Increases ProductivityThe in-line suction and discharge of the Prosser Standard-Line pumps permits pumps to be connected in series providing double the discharge pressure. Series operation enables you to use the same pumps on different jobs with varying head requirements or with smaller diameter well casings. While a single pump may be sufficient for one job, simply connecting pumps in a series permits two small pumps to do the work of one large pump.

Since 1942, people who require quality and performance have specified Prosser® Pumps.

2015 Crane Pumps & Systems, Inc. A Crane Co. CompanyPrinted in U.S.A.PROSTDBRO - Rev. B (1/15)Crane Pumps & Systems Canada

83 West DriveBrampton, Ont. Canada L6T 2J6(905) 457-6223Fax (905) 457-2650

Crane Pumps & Systems420 Third StreetPiqua, Ohio 45356(937) 778-8947Fax (937) 773-7157www.cranepumps.com

A Crane Co. Company

brands you trust.

1855 2015