ProgSkeet Tutorial 360CLIP

Set Up 360Clip-NAND

Hardware: Progskeet 1.1 Injectus 360Clip-NAND

Auxiliary device: 2x USB cable

Software: InfectusProgrammer-3.9.9.0 (Folder "USB-Drivers3.1":Usb drivers to manage

INJECTUS devices under WINDOWS)

ProgSkeet_Bitstreams_111126 (DAT:bitstreams in DAT format (Actel DirectC; Injectus for example) SL_NAND: when using Solderless NAND clip addon)

Zadig.exe (for older ProgSkeet_110819 or Winskeet40000_111004 you need the driver libusb0, for newer Winskeet111205 you select WinUSB with ZADIG.EXE)

Bitstream programming solderless NAND

Download from http://www.infectus.biz/downloads.php Open the directory where you have extracted Infectus

Programmer 3.9.9.0

Open now InfectusProgrammer_3.9.9.0.exe

Connect injectus on pc usb-port

Connect progskeet on other pc usb-port

both connected to usb

If you get Board not present check device manager if right injectus drivers loaded

if injectus detected then can be started

In the Actel Panel, click Load DAT (ProgSkeet_Retail_SL_NAND111126.dat)

proceed programming (progress see points)

Programming needs few minutes, wait patiently for DONE!

connecting the NAND clip(s) and dump NANDs

Hardware: Progskeet 1.1 360Clip(s)-NAND, flat-cable to subboard (blue mark on same level side) 50 pin flat-cable, subboard

Auxiliary device: 1x USB cable 1x spring clamps (to press on clip) 1x fine cutter 1x cleaning brush 1x soldering iron, solder 2x wire (e.g. awg26) or IDE-cable or CAT5-cable 1x alcohol (isopropyl) cleaning compound

Software: Winskeet111205 (+ driver zadig.exe) , program working on single nand FlowRebuilder v.4.2.1.1.exe (e.g. http://www.mediafire.com/?7d6guqfeqip1nhy) Setup_HxD.exe (e.g. http://mh-nexus.de/en/hxd/)

Hardware

flat-cable blue mark on same level side progskeet 1.1 subboard 360Clip-NAND

USB cable spring clamps (to press on clip) fine cutter cleaning brush wire (e.g. awg26) or IDE-cable or CAT5-cable soldering iron, solder

alcohol (isopropyl) cleaning compound

Auxiliary device

Set-up 360Clip-NAND (to rework)

Set-up Progskeet (solderbridge added on R9 and R11 to enable 3.3V and wire solder to subboard +3,3 and GND)

Set-up Progskeet (after cleaning contacts mounting flat-cable and spring clamp on NAND 0)

Set-up WingSkeet40000 (open WinSkeet40000, Common tab and go to the NAND tab)

Common tab NAND tab ( select NAND 1)

Set-up WingSkeet40000 (NAND 0)

click Auto check if manufact. on the NAND flash does correspond

click Dump and select file name for NAND 0

progress are normal slow , so if progress ist really fast, check conections or Common settings

Set-up WingSkeet40000 (NAND 0)

Set-up Progskeet (after cleaning contacts mounting flat-cable and spring clamp on NAND 1)

Set-up WingSkeet40000 (NAND 1)

click Auto check if manufact. on the NAND flash does correspond

click Dump and select file name for NAND 1

progress are normal slow , so if progress ist really fast, check conections or Common settings

Set-up WingSkeet40000 (NAND 1)

ProgSkeet Tutorial 360CLIPSet Up360Clip-NANDBitstream programmingsolderless NAND Foliennummer 4Foliennummer 5Foliennummer 6connecting the NAND clip(s) and dump NANDsHardwareAuxiliary deviceSet-up 360Clip-NAND(to rework)Set-up Progskeet(solderbridge added on R9 and R11 to enable 3.3V and wire solder to subboard +3,3 and GND)Set-up Progskeet(after cleaning contacts mounting flat-cable and spring clamp on NAND 0)Set-up WingSkeet40000(open WinSkeet40000, Common tab and go to the NAND tab)Set-up WingSkeet40000(NAND 0)Set-up WingSkeet40000(NAND 0)Set-up Progskeet(after cleaning contacts mounting flat-cable and spring clamp on NAND 1)Set-up WingSkeet40000(NAND 1)Set-up WingSkeet40000(NAND 1)