Upload
dinhcong
View
218
Download
0
Embed Size (px)
Citation preview
0 60 5
Wingate Program Contents
G U E S T R O O M S - C P - 0 3
Pattern: I38894 12 ft
C O R R I D O R , L O B B Y , E L E V A T O R L O B B I E S , M E E T I N G R O O M S & S T O R A G E C P - 0 1
Pattern: I38143 15 ft
I N T E R I O R S T A I R W E L L - C P - 0 5
Pattern: I44665 12 ft
B O H - M I S C A R E A S - C P - 0 4
Pattern: I44666 12 ft
S T A I R S 1 , S T A I R S 2 , S O L I D B A N D I N G @ B U L L N O S E C P - 0 6( C A N B E U S E D W I T H I I 3 8 1 4 3 , I 3 8 1 7 1 , A N D I 3 8 8 9 4 A S C O V E B A S E M A T E R I A L , T R A N S I T I O N , O R F I L L W I T H W Y N D H A M A P P R O V A L )
Pattern: C34276-3120
0 2
0 4
0 1
0 3
C O R R I D O R , L O B B Y , E L E V A T O R L O B B I E S , M E E T I N G R O O M S & S T O R A G E C P - 0 1
Pattern: I38171 12 ft
0 7
M I S C E L L A N E O U S T R A N S I T I O N( C A N B E U S E D W I T H I 4 4 6 6 6 A S C O V E B A S E M A T E R I A L , T R A N S I T I O N , O R F I L L W I T H W Y N D H A M A P P R O V A L )
Pattern: C34275-3250
G U E S T R O O M S - C P - 0 3P AT T E R N # : I 3 8 8 9 4
CONSTRUCTION: HIGH PERFORMANCE LOOP/CUT
DYE METHOD: SOLUTION
PILE FIBER: 100% SDN
TUFTED PILE WEIGHT: 32 OZ. PER SQ YD
STITCH RATE: 15 STITCHES PER INCH
PILE HEIGHT: .181 AVERAGE
DENSITY FACTOR: 6,364
WEIGHT DENSITY FACTOR: 203,648
TOPICAL STAIN TREATMENT:SCOTCHGARD®
WIDTH: 12’
PATTERN REPEAT: 24’’ W X 24’’ L
PRIMARY BACKING: WOVEN POLYPROPYLENE
SECONDARY BACKING: ACTIONBAC®
WARRANTY: TEN (10) YEAR LIMITED WEAR
CERTIFICATION: CRI GLP2121
ASTM E-648 FLOORING RADIANT PANEL: CLASS 1
DOC-FF1-70 METHENAMINE PILL TEST: PASSES
AATCC 134 ELECTROSTATIC PROPENSITY: < 3.5 KV
E-662 CHAMBER: LESS THAN 45O
specifications are based on averages from manufacturing processes and may vary within normal industry tolerances. material supply and /or manufacturing processes may necessitate specification changes without notice. such variations do not affect product performance.
this carpet is manufactured and recommended for floor covering use only. as in all quality carpet, colors are subject to dye lot variations. for optimum side match and finished seam appearance, this product should be installed whenever possible, with seams running perpendicular to major external (outside) light sources.
the equipment used to manufacture patterned carpet may create visible lines in both length and width directions. this characteristic will not always be detect-able in small samples and is not considered a manufacturing defect. as with all patterned carpets, perfect pattern match may not be obtainable at seams. tolerances in pattern registration – bow and skew – are to be expected. all seams and cut edges at doors and closets must be seam sealed.
chair pads are recommended under chairs with rollers to preserve appearance retention, avoid premature or accelerated wear, and act as a deterrent toward delamination. special backing systems are available that do not require chair pads. walk off mats are recommended at building entry ways to reduce soiling.
please call signature’s technical services department at 800-809-7086 for any questions or assistance.
A
120.197
B
3719
C
3129
D
3141
0 1
B O H - M I S C A R E A S - C P - 0 4P AT T E R N # : I 4 4 6 6 6
CONSTRUCTION: HIGH PERFORMANCE LOOP/CUT
DYE METHOD: SOLUTION
PILE FIBER: 100% SDN
TUFTED PILE WEIGHT: 36 OZ. PER SQ YD
STITCH RATE: 16 STITCHES PER INCH
PILE HEIGHT: .184 AVERAGE
DENSITY FACTOR: 7,063
WEIGHT DENSITY FACTOR: 254,256
TOPICAL STAIN TREATMENT:SCOTCHGARD® AVAIALBLE
WIDTH: 12’
PATTERN REPEAT: 12’’ W X 12’’ L
PRIMARY BACKING: WOVEN POLYPROPYLENE
SECONDARY BACKING: ACTIONBAC®
WARRANTY: TEN (10) YEAR LIMITED WEAR
CERTIFICATION: CRI GLP2121
ASTM E-648 FLOORING RADIANT PANEL: CLASS 1
DOC-FF1-70 METHENAMINE PILL TEST: PASSES
AATCC 134 ELECTROSTATIC PROPENSITY: < 3.5 KV
E-662 CHAMBER: LESS THAN 45O
specifications are based on averages from manufacturing processes and may vary within normal industry tolerances. material supply and /or manufacturing processes may necessitate specification changes without notice. such variations do not affect product performance.
this carpet is manufactured and recommended for floor covering use only. as in all quality carpet, colors are subject to dye lot variations. for optimum side match and finished seam appearance, this product should be installed whenever possible, with seams running perpendicular to major external (outside) light sources.
the equipment used to manufacture patterned carpet may create visible lines in both length and width directions. this characteristic will not always be detect-able in small samples and is not considered a manufacturing defect. as with all patterned carpets, perfect pattern match may not be obtainable at seams. tolerances in pattern registration – bow and skew – are to be expected. all seams and cut edges at doors and closets must be seam sealed.
chair pads are recommended under chairs with rollers to preserve appearance retention, avoid premature or accelerated wear, and act as a deterrent toward delamination. special backing systems are available that do not require chair pads. walk off mats are recommended at building entry ways to reduce soiling.
please call signature’s technical services department at 800-809-7086 for any questions or assistance.
A
3250
B
3249
C
3507
0 2
C O R R I D O R , L O B B Y , E L E V A T O R L O B B I E S , M E E T I N G R O O M S & S T O R A G E C P - 0 1P AT T E R N # : I 3 8 1 4 3
CONSTRUCTION: HIGH PERFORMANCE LOOP/CUT
DYE METHOD: SOLUTION
PILE FIBER: 100% SDN
TUFTED PILE WEIGHT: 36 OZ. PER SQ YD
STITCH RATE: 13 STITCHES PER INCH
PILE HEIGHT: .218 AVERAGE
DENSITY FACTOR: 4,954
WEIGHT DENSITY FACTOR: 148,620
TOPICAL STAIN TREATMENT:SCOTCHGARD®
WIDTH: 15’
PATTERN REPEAT: 90’’ W X 90’’ L
PRIMARY BACKING: WOVEN POLYPROPYLENE
SECONDARY BACKING: ACTIONBAC®
SECONDARY BACKING: OPTIONAL
WARRANTY: TEN (10) YEAR LIMITED WEAR
CERTIFICATION: CRI GLP2121
ASTM E-648 FLOORING RADIANT PANEL: CLASS 1
DOC-FF1-70 METHENAMINE PILL TEST: PASSES
AATCC 134 ELECTROSTATIC PROPENSITY: < 3.5 KV
E-662 CHAMBER: LESS THAN 45O
specifications are based on averages from manufacturing processes and may vary within normal industry tolerances. material supply and /or manufacturing processes may necessitate specification changes without notice. such variations do not affect product performance.
this carpet is manufactured and recommended for floor covering use only. as in all quality carpet, colors are subject to dye lot variations. for optimum side match and finished seam appearance, this product should be installed whenever possible, with seams running perpendicular to major external (outside) light sources.
the equipment used to manufacture patterned carpet may create visible lines in both length and width directions. this characteristic will not always be detect-able in small samples and is not considered a manufacturing defect. as with all patterned carpets, perfect pattern match may not be obtainable at seams. tolerances in pattern registration – bow and skew – are to be expected. all seams and cut edges at doors and closets must be seam sealed.
chair pads are recommended under chairs with rollers to preserve appearance retention, avoid premature or accelerated wear, and act as a deterrent toward delamination. special backing systems are available that do not require chair pads. walk off mats are recommended at building entry ways to reduce soiling.
please call signature’s technical services department at 800-809-7086 for any questions or assistance.
A
120.197
B
3719
C
3129
D
3141
0 3
C O R R I D O R , L O B B Y , E L E V A T O R L O B B I E S , M E E T I N G R O O M S & S T O R A G E C P - 0 1 P AT T E R N # : I 3 8 1 7 1
CONSTRUCTION: HIGH PERFORMANCE LOOP/CUT
DYE METHOD: SOLUTION
PILE FIBER: 100% SDN
TUFTED PILE WEIGHT: 36 OZ. PER SQ YD
STITCH RATE: 13 STITCHES PER INCH
PILE HEIGHT: .281 AVERAGE
DENSITY FACTOR: 4,954
WEIGHT DENSITY FACTOR: 148,620
TOPICAL STAIN TREATMENT:SCOTCHGARD®
WIDTH: 12’
PATTERN REPEAT: 72’’ W X 90’’ L
PRIMARY BACKING: WOVEN POLYPROPYLENE
SECONDARY BACKING: ACTIONBAC®
SECONDARY BACKING: OPTIONAL
WARRANTY: TEN (10) YEAR LIMITED WEAR
CERTIFICATION: CRI GLP2121
ASTM E-648 FLOORING RADIANT PANEL: CLASS 1
DOC-FF1-70 METHENAMINE PILL TEST: PASSES
AATCC 134 ELECTROSTATIC PROPENSITY: < 3.5 KV
E-662 CHAMBER: LESS THAN 45O
specifications are based on averages from manufacturing processes and may vary within normal industry tolerances. material supply and /or manufacturing processes may necessitate specification changes without notice. such variations do not affect product performance.
this carpet is manufactured and recommended for floor covering use only. as in all quality carpet, colors are subject to dye lot variations. for optimum side match and finished seam appearance, this product should be installed whenever possible, with seams running perpendicular to major external (outside) light sources.
the equipment used to manufacture patterned carpet may create visible lines in both length and width directions. this characteristic will not always be detect-able in small samples and is not considered a manufacturing defect. as with all patterned carpets, perfect pattern match may not be obtainable at seams. tolerances in pattern registration – bow and skew – are to be expected. all seams and cut edges at doors and closets must be seam sealed.
chair pads are recommended under chairs with rollers to preserve appearance retention, avoid premature or accelerated wear, and act as a deterrent toward delamination. special backing systems are available that do not require chair pads. walk off mats are recommended at building entry ways to reduce soiling.
please call signature’s technical services department at 800-809-7086 for any questions or assistance.
A
120.197
B
3719
C
3129
D
3141
0 4
I N T E R I O R S T A I R W E L L - C P - 0 5P AT T E R N # : I 4 4 6 6 5CONSTRUCTION: HIGH PERFORMANCE LOOP/CUT
DYE METHOD: SOLUTION
PILE FIBER: 100% SDN
TUFTED PILE WEIGHT: 36 OZ. PER SQ YD
STITCH RATE: 17 STITCHES PER INCH
PILE HEIGHT: .179 AVERAGE
DENSITY FACTOR: 7,256
WEIGHT DENSITY FACTOR: 261,222
TOPICAL STAIN TREATMENT:SCOTCHGARD®
WIDTH: 12’
PATTERN REPEAT: 12’’ W X 14’’ L
PRIMARY BACKING: WOVEN POLYPROPYLENE
SECONDARY BACKING: HIGH PERFORMANCE
ACTIONBAC®
WARRANTY: TEN (10) YEAR LIMITED WEAR
CERTIFICATION: CRI GLP2121
ASTM E-648 FLOORING RADIANT PANEL: CLASS 1
DOC-FF1-70 METHENAMINE PILL TEST: PASSES
AATCC 134 ELECTROSTATIC PROPENSITY: < 3.5 KV
E-662 CHAMBER: LESS THAN 45O
specifications are based on averages from manufacturing processes and may vary within normal industry tolerances. material supply and /or manufacturing processes may necessitate specification changes without notice. such variations do not affect product performance.
this carpet is manufactured and recommended for floor covering use only. as in all quality carpet, colors are subject to dye lot variations. for optimum side match and finished seam appearance, this product should be installed whenever possible, with seams running perpendicular to major external (outside) light sources.
the equipment used to manufacture patterned carpet may create visible lines in both length and width directions. this characteristic will not always be detect-able in small samples and is not considered a manufacturing defect. as with all patterned carpets, perfect pattern match may not be obtainable at seams. tolerances in pattern registration – bow and skew – are to be expected. all seams and cut edges at doors and closets must be seam sealed.
chair pads are recommended under chairs with rollers to preserve appearance retention, avoid premature or accelerated wear, and act as a deterrent toward delamination. special backing systems are available that do not require chair pads. walk off mats are recommended at building entry ways to reduce soiling.
please call signature’s technical services department at 800-809-7086 for any questions or assistance.
A
3250
B
3105
C
3112
0 5
S T A I R S " T R A N S I T I O N " - C P - 0 6( C A N B E U S E D W I T H I 3 8 1 4 3 , I 3 8 1 7 1 , A N D I 3 8 8 9 4 A S C O V E B A S E M A T E R I A L , T R A N S I T I O N , O R F I L L W I T H W Y N D H A M A P P R O V A L )
P AT T E R N # : I 3 4 2 7 6 - 3 1 2 0
CONSTRUCTION: CUT PILE SOLIDS
DYE METHOD: SOLUTION
PILE FIBER: 100% SDN
TUFTED PILE WEIGHT: 32 OZ. PER SQ YD
STITCH RATE: 15 STITCHES PER INCH
PILE HEIGHT: .250 AVERAGE
DENSITY FACTOR: 5,184
WEIGHT DENSITY FACTOR: 186,624
TOPICAL STAIN TREATMENT:SCOTCHGARD®
WIDTH: 12’
PATTERN REPEAT: N/A
PRIMARY BACKING: WOVEN POLYPROPYLENE
SECONDARY BACKING: HIGH PERFORMANCE
ACTIONBAC®
WARRANTY: TEN (10) YEAR LIMITED WEAR
CERTIFICATION: CRI GLP2121
ASTM E-648 FLOORING RADIANT PANEL: CLASS 1
DOC-FF1-70 METHENAMINE PILL TEST: PASSES
AATCC 134 ELECTROSTATIC PROPENSITY: < 3.5 KV
E-662 CHAMBER: LESS THAN 45O
specifications are based on averages from manufacturing processes and may vary within normal industry tolerances. material supply and /or manufacturing processes may necessitate specification changes without notice. such variations do not affect product performance.
this carpet is manufactured and recommended for floor covering use only. as in all quality carpet, colors are subject to dye lot variations. for optimum side match and finished seam appearance, this product should be installed whenever possible, with seams running perpendicular to major external (outside) light sources.
the equipment used to manufacture patterned carpet may create visible lines in both length and width directions. this characteristic will not always be detect-able in small samples and is not considered a manufacturing defect. as with all patterned carpets, perfect pattern match may not be obtainable at seams. tolerances in pattern registration – bow and skew – are to be expected. all seams and cut edges at doors and closets must be seam sealed.
chair pads are recommended under chairs with rollers to preserve appearance retention, avoid premature or accelerated wear, and act as a deterrent toward delamination. special backing systems are available that do not require chair pads. walk off mats are recommended at building entry ways to reduce soiling.
please call signature’s technical services department at 800-809-7086 for any questions or assistance.
A
3120
0 6
M I S C E L L A N E O U S T R A N S I T I O NP AT T E R N # : I 3 4 2 7 5 - 3 2 5 0
CONSTRUCTION: CUT PILE SOLIDS
DYE METHOD: SOLUTION
PILE FIBER: 100% SDN
TUFTED PILE WEIGHT: 32 OZ. PER SQ YD
STITCH RATE: 15 STITCHES PER INCH
PILE HEIGHT: .250 AVERAGE
DENSITY FACTOR: 5,184
WEIGHT DENSITY FACTOR: 186,624
TOPICAL STAIN TREATMENT:SCOTCHGARD®
WIDTH: 12’
PATTERN REPEAT: N/A
PRIMARY BACKING: WOVEN POLYPROPYLENE
SECONDARY BACKING: HIGH PERFORMANCE
ACTIONBAC®
WARRANTY: TEN (10) YEAR LIMITED WEAR
CERTIFICATION: CRI GLP2121
ASTM E-648 FLOORING RADIANT PANEL: CLASS 1
DOC-FF1-70 METHENAMINE PILL TEST: PASSES
AATCC 134 ELECTROSTATIC PROPENSITY: < 3.5 KV
E-662 CHAMBER: LESS THAN 45O
specifications are based on averages from manufacturing processes and may vary within normal industry tolerances. material supply and /or manufacturing processes may necessitate specification changes without notice. such variations do not affect product performance.
this carpet is manufactured and recommended for floor covering use only. as in all quality carpet, colors are subject to dye lot variations. for optimum side match and finished seam appearance, this product should be installed whenever possible, with seams running perpendicular to major external (outside) light sources.
the equipment used to manufacture patterned carpet may create visible lines in both length and width directions. this characteristic will not always be detect-able in small samples and is not considered a manufacturing defect. as with all patterned carpets, perfect pattern match may not be obtainable at seams. tolerances in pattern registration – bow and skew – are to be expected. all seams and cut edges at doors and closets must be seam sealed.
chair pads are recommended under chairs with rollers to preserve appearance retention, avoid premature or accelerated wear, and act as a deterrent toward delamination. special backing systems are available that do not require chair pads. walk off mats are recommended at building entry ways to reduce soiling.
please call signature’s technical services department at 800-809-7086 for any questions or assistance.
0 7
( C A N B E U S E D W I T H I 4 4 6 6 6 A S C O V E B A S E M A T E R I A L , T R A N S I T I O N , O R F I L L W I T H W Y N D H A M A P P R O V A L )
A
3250