Product Specification - USCO America

-1- 14A4A2-00089E-3

InfoSOSA™ Series

Touchscreen Display

Model “7”

Product Specification

Seedsware Corporation

http://www.seedsware.co.jp/global/

Contents in this document may change without prior notice.

Please obtain the delivery specification for the latest design.

- 2 - 14A4A2-00089E-3

Table of Contents

Table of Contents ........................................................................................................................................................... 2

1. Summary .................................................................................................................................................................. 4

2. Model “7” Products ................................................................................................................................................... 4

3. Packaged Contents .................................................................................................................................................. 5

4. Unit Specifications .................................................................................................................................................... 9

1) RoHS Directives............................................................................................................................................ 14

1) Power Connector .......................................................................................................................................... 14

2) Serial Ports (SIO1/ SIO2) .............................................................................................................................. 14

3) Sheet Key Interface (for Switch) .................................................................................................................... 17

4) Sheet Key Interface (for LED) ....................................................................................................................... 18

5. Battery Board Specifications .................................................................................................................................. 19

1) RoHS Directives............................................................................................................................................ 20

1) Interface for Connecting with Unit ................................................................................................................. 20

6. Battery Specifications ............................................................................................................................................. 20

7. Cable Specifications ............................................................................................................................................... 21

8. AC Adaptor Specification ........................................................................................................................................ 22

9. Developing Environment ........................................................................................................................................ 22

2-1 General Specifications ...................................................................................................................................... 4

2-2 Introduction Sample Kit ..................................................................................................................................... 4

3-1 Standard Specification ...................................................................................................................................... 5

3-2 Introduction Sample Kit ..................................................................................................................................... 6

4-1 Performance ..................................................................................................................................................... 9

4-2 Electrical Specification .................................................................................................................................... 12

4-3 Appearance Specification ................................................................................................................................ 13

4-4 Environment Specification ............................................................................................................................... 14

4-5 Compliance ..................................................................................................................................................... 14

4-6 External Interfaces .......................................................................................................................................... 14

4-7 Product Label .................................................................................................................................................. 19

5-1 Performance ................................................................................................................................................... 19

5-2 Appearance Specification ................................................................................................................................ 19

5-3 Environment Specification ............................................................................................................................... 19

5-4 Compliances ................................................................................................................................................... 20

5-5 External Interface ............................................................................................................................................ 20

6-1 Specifications .................................................................................................................................................. 20

7-1 Power Cable ................................................................................................................................................... 21

7-2 Communication Cable for SIO 1 ...................................................................................................................... 21

7-3 Battery Cable .................................................................................................................................................. 21

7-4 Power Cable (for AC Adaptor) ......................................................................................................................... 22

- 3 - 14A4A2-00089E-3

10. Mounting the Unit ................................................................................................................................................... 23

11. Warranty ................................................................................................................................................................ 28

12. Production Discontinuance ..................................................................................................................................... 28

13. Others .................................................................................................................................................................... 29

Appendix: Outline diagrams

9-1 Development Tool ........................................................................................................................................... 22

10-1 Mounting Conditions ..................................................................................................................................... 23

10-2 Mounting ....................................................................................................................................................... 23

10-3 Panel Opening Example................................................................................................................................ 24

11-1 Warranty Period............................................................................................................................................. 28

11-2 Warranty Exceptions ..................................................................................................................................... 28

- 4 - 14A4A2-00089E-3

1. Summary

You can operate your device easily and get LCDs with various expressions by interactive operations of

the touchscreen, made possible by communicating with the host device.

This document describes the specifications of the 7” model touchscreen displays.

2. Model “7” Products

2-1 General Specifications

Model Specification Distinction*

IS701-3SSN2-001 3.5” QVGA(320 x 240) 4,096colors Open Frame 1 language

IS711-4SSN3-001 4.3” WQVGA(480 x 272) 4,096 colors Open Frame 1 language

IS701-5SSN1-001 5.7” QVGA(320 x 240) 65,536 colors Open Frame 1 language

IS701-5SSN1-101 5.7” VGA(640 x 480) 65,536 colors Open Frame 1 language

* Product specification listed items:

“Display size/Resolutions/Displayed colors/Chassis type/ Maximum support language”

・1 language (Maximum of 1 system font language can be used.)

Specification varies according to the model.

This specification provides information according to each distinctive model.

2-2 Introduction Sample Kit

Tool for development will be included with the Standard specification article.

Model Specification Distinction*

IS701-3SSN2-001-KIT 3.5” QVGA(320 x 240) 4,096colors Open Frame 1 language

IS711-4SSN3-001-KIT 4.3” WQVGA(480 x 272) 4,096 colors Open Frame 1 language

IS701-5SSN1-001-KIT 5.7” QVGA(320 x 240) 65,536 colors Open Frame 1 language

IS701-5SSN1-101-KIT 5.7” VGA(640 x 480) 65,536 colors Open Frame 1 language

* Product specification listed items:

“Display size/Resolutions/Displayed colors/Chassis type/ Maximum support language”

・1 language (Maximum of 1 system font language can be used.)

Specification varies according to the model.

This specification provides information according to each distinctive model.

Note: Introduction Sample kit unit specification is the same as that of the standard specification unit.

- 5 - 14A4A2-00089E-3

3. Packaged Contents

3-1 Standard Specification

3.5”

Packaged Content IS701-3SSN2-001

・Main Unit 10 units/box

4.3”



5.7”


IS701-5SSN1-101


- 6 - 14A4A2-00089E-3

3-2 Introduction Sample Kit

3.5”

Packaged Contents IS701-3SSN2-001-KIT

・Main unit 1pc

・Power Cable (ISCBL-S01-001) 1pc

・Communication cable for SIO1

(ISCBL-S02-001) 1pc

・AC Adaptor 1pc

・Power Cable (AC adaptor) 1pc

・Accessory list 1pc

・CD 2pcs*1

Below files are include in the CD.


Instruction Manual

InfoSOSA Installation Guide

InfoSOSA Builder Installer

InfoSOSA Builder Operation Manual

Reference Manual

Host Communication Tester Instruction Manual

Release Note

User Registration Form

*1. Includes 2 CDS: 1 Japanese version and 1 English version.

- 7 - 14A4A2-00089E-3

4.3”


・Main unit 1pc



(ISCBL-S02-001) 1pc

・AC Adaptor 1pc


・Accessory list 1pc

・CD 2pcs*1



Instruction Manual




Reference Manual


Release Note



- 8 - 14A4A2-00089E-3

5.7”


IS701-5SSN1-101-KIT

・Main unit 1pc



(ISCBL-S02-001) 1pc

・AC Adaptor 1pc


・Battery Board (IS-BT-01) 1pc

・Battery (CR2032) 1pc

・Battery Cable (ISCBL-S04-001) 1pc

・Accessory List 1pc

・CD 2pcs*1



Instruction Manual




Reference Manual


Release Note



- 9 - 14A4A2-00089E-3

4. Unit Specifications

4-1 Performance

3.5”

Items Specifications

IS701-3SSN2-001

Display

Type 3.5”TFT LCD

Resolution 320(W) x 240(H)

Color 4,096 Colors

Backlight LED Backlight (Brightness can be adjusted by 8 levels)

On/Off function, automatic Off function

Language*3

System Font*1

Select 1 from below languages:

・Japanese

・Korean

・English and European language

Image Font*2

Memory Capacity User Flash Memory 5MB

Touch Screen

Type Analog Resistive

Resolution 320 x 240

Input Method Finger or R0.8 Polyacetal pen

Expected Life Finger Operation : 10,000,000 strokes

Pen Operation : 100,000 characters

Touch Sound Yes

Serial I/F SIO1 RS232 (TXD,RXD,RTS,CTS) Nylon Connector

SIO2*3 RS232 (TXD,RXD) Nylon Connector

Sheet Key I/F Switch －

LED －

Battery I/F －

Other I/O Buzzer Variable Frequency

RTC ―

*1. English (alphabet) is included in all languages.

*2. Fonts installed in the computer can be displayed as bitmaps.

*3. May not be available or have different specifications according to the software versions.

Please refer to the Reference Manual of each version for details.

- 10 - 14A4A2-00089E-3

4.3”


IS711-4SSN3-001

Display

Type 4.3”TFTLCD

Resolution 480(W) x 272(H)

Color 4,096 Colors



Language*3

System Font*1


・Japanese

・Korean


Image Font*2

Memory Capacity User Flash

Memory 5MB

Touch Screen


Resolution 480 x 272




Touch Sound Yes

Serial I/F SIO1 RS232 (TXD,RXD,RTS,CTS) Nylon Connector


Sheet Key I/F Switch Maximum 24 points (Matrix Key 4 x 6) (FFC Connector)

LED Maximum 8 points (FFC Connector)

Battery I/F ―


RTC ―





- 11 - 14A4A2-00089E-3

5.7”


IS701-5SSN1-001 IS701-5SSN1-101

Display

Type 5.7”TFTLCD

Resolution 320(W) x 240(H) 640(W) x 480(H)

Color 65,536 Colors



Language*3

System Font*1


・Japanese

・Korean


Image Font*2

Memory Capacity Internal Memory

for screen saving 6MB

Touch Screen


Resolution 320 x 240 640 x 480




Touch Sound Yes

Serial I/F SIO1 RS232 TXD,RXD,RTS,CTS) Nylon Connector


Sheet key I/F Switch Maximum 24 points (Matrix key 4 x 6) (FFC Connector)

LED Maximum 8 points (FFC Connector)

Battery I/F Complying battery nominal voltage3 to 3.6V( Nylon Connector)


RTC*4 ±65 seconds/month (Error at room temperature, no power flow.)





*4. External battery needs to be connected to Battery I/F in order to back up the RTC.

Set to correct time on a regular basis when using on systems where time error is a problem,

- 12 - 14A4A2-00089E-3

4-2 Electrical Specification

3.5”/ 4.3”/ 5.7”

Items

Specifications

3.5” 4.3” 5.7”

IS701-3SSN2-001 IS711-4SSN3-001 IS701-5SSN1-001 IS701-5SSN1-101

Absolute Maximum

Rated Voltage 0-6V DC

Rated Power

Voltage Range 5V DC±5％

Power Consumption TYP．210mA *1 TYP．300mA *1 TYP．500mA *1 TYP．610mA *1

MAX．400mA MAX．500mA MAX．800mA MAX．950mA

Backup Current

(RTC)*2

― ― TYP．1μA

― ― MAX．35μA

GND Frame

Connection GND (Signal GND) and Frame (Sheet metal) are connected inside the unit.

*1 LCD display set at brightness level 4 in 25℃

*2 External battery needs to be connected to Battery I/F in order to back up the RTC.

Note: When gentle power source is used for rising and falling of power, it may not operate properly. Also, when

rebooting, leave it off for a while after turning off; do not turn the power back on immediately. It may not

boot up accurately.

- 13 - 14A4A2-00089E-3

4-3 Appearance Specification

3.5”


IS701-3SSN2-001

External Dimension

(Does not include projections) 88(W) x 70(H) x 22.1(D)mm*1

Weight Approximately 140g

4.3”


IS711-4SSN3-001

External Dimension


Weight Approximately 250g

5.7”


IS701-5SSN1-001 IS701-5SSN1-101

External Dimension


164(W) x 109(H) x

30.9(D)mm*1

Weight Approximately 400g Approximately 470g

*1. Error margin not included. Please refer to each outline diagram for details.

- 14 - 14A4A2-00089E-3

4-4 Environment Specification

3.5”/ 4.3”/ 5.7”


Ambient Operating Temperature 0 to 50℃*1

Ambient Storage Temperature -20 to 80℃*1

Ambient Operating Humidity 10 to 80%RH

(Non-condensing, Wet bulb temperature is 39℃or less)

Ambient Storage Humidity 10 to 80%RH


Dust 0.1mg/m2 or less (conductive dust prohibited.)

Corrosive Gas Prohibited

Vibration Resistance

5 to 9Hz Half amplitude 3.5mm

9 to 150Hz Fixed acceleration 9.8m/s２

X,Y,Z each direction 10 times (for 100 minutes)

(JIS B 3502, IEC61131-2 Compliant)

4-5 Compliance

1) RoHS Directives

3.5”/ 4.3”/ 5.7”

Complies with the RoHS Directives of EU.

4-6 External Interfaces

1) Power Connector

3.5”/ 4.3”/ 5.7”

Interface : 5V DC IN

Connector : Nylon Connector

Model : BM02B-PASS-1-TFT (JST) equivalent

Pin No. Signal

1 +5V

2 GND*1

*1 GND (Signal Ground) and frame (Sheet metal) are connected inside the unit.

2) Serial Ports (SIO1/ SIO2)

Set the communication specification with the InfoSOSA builder.

* Specifications vary according to the software version.


- 15 - 14A4A2-00089E-3

SIO1

3.5”/ 4.3”/ 5.7”

SIO1 can be used at Host Communication and at download.

Interface : RS232C


Model : B5B-PH-K-S (JST) equivalent

Pin No. Signal Direction

1 RXD InfoSOSA <- Host

2 TXD InfoSOSA -> Host

3 GND -

4 RTS InfoSOSA -> Host

5 CTS InfoSOSA <- Host

Communication

Items Specification

Baud Rate 4800/9600/19200/38400/57600/115200bps

Data Length 8 Bit

Parity None/Odd/Even

Stop Bit 1 Bit

Flow Control None/Hardware flow control (RTS/CTS control)

Default Setting

Communication specification at factory state:

Items Specification

Baud Rate 115200bps

Data Length 8 Bit

Parity None

Stop Bit 1 Bit

Flow Control Hardware flow control (RTS/CTS control)

- 16 - 14A4A2-00089E-3

SIO2

3.5”/ 4.3”/ 5.7”

SIO 2 can be used at host communication and download.

Interface : RS232C

■ 3.5”/ 4.3”/ 5.7” VGA






3 GND -

■ 5.7” QVGA






3 GND -

4 NC Do not connect

5 NC Do not connect

6 NC Do not connect

Communication

Items Specification

Baud Rate 4800/9600/19200/38400/57600/115200bps

Data Length 8 Bit

Parity None/Odd/Even

Stop Bit 1 Bit

Flow Control None

Default Setting

Communication specification at factory state:

Items Specification

Baud Rate 115200bps

Data Length 8 Bit

Parity None

Stop Bit 1 Bit

Flow Control None

- 17 - 14A4A2-00089E-3

3) Sheet Key Interface (for Switch)

4.3”Open Frame/ 5.7”

Connector : FFC Connector (1mm pitch bottom contact)

Model : 00-6200-107-032-800+ (KYOCERA Connector Products Corporation)

Pin No. Signal

1 SCAN4

2 SCAN3

3 SCAN2

4 SCAN1

5 RETURN6

6 RETURN5

7 RETURN4

8 RETURN3

9 RETURN2

10 RETURN1

Maximum 24 switch input is possible with the key matrix.

(Scan 4 x Return 6)

Switch of the matrix circuit as shown in the below diagram can be connected.

Switch input is recognized with the numbers shown below with the InfoSOSA.

* Do not press multiple switches simultaneously. It may result in incorrect input.

Specification of compatible cable

XSW01

XSW02

XSW03

XSW04

XSW05

XSW06

XSW07

XSW08

XSW09

XSW10

XSW11

XSW12

XSW13

XSW14

XSW15

XSW16

XSW17

XSW18

XSW19

XSW20

XSW21

XSW22

XSW23

XSW24

RETURN 1

SCAN 1

RETURN 2

RETURN 3

RETURN 4

RETURN 5

RETURN 6

SCAN 2 SCAN 3 SCAN 4

- 18 - 14A4A2-00089E-3

4) Sheet Key Interface (for LED)

4.3” Open frame/ 5.7”

Connector : FFC Connector (1mm Pitch bottom contact)

Model : 00-6200-097-032-800+(KYOCERA Connector Products Corporation)

Pin No. Signal

1 LED_VCC

2 XLED1

3 XLED2

4 XLED3

5 XLED4

6 XLED5

7 XLED6

8 XLED7

9 XLED8

Maximum of 8 points

LED of the LED circuit of below diagram can be connected.

By outputting to the LED number shown below with the InfoSOSA, the LED will can be turned ON or

OFF.

Specification of compatible cable

VCC：5V

Limiting Resistor：1KΩ(Built in to Substrate)

XLED1

XLED2

XLED3

XLED4

XLED5

XLED6

XLED7

XLED8

VCC

- 19 - 14A4A2-00089E-3

5) Battery

5.7”

Connector

Model : IL-2P-S3EN2-1(JAE) Equivalent

Pin No. Signal

1 +

2 -

* RTC can be backed up by connecting a dedicated battery board (IS-BT-01) or a battery with a cable.

* Battery must be of nominal voltage of 3 to 3.6VDC

4-7 Product Label

3.5”/ 4.3”/ 5.7”

5. Battery Board Specifications

5.7”

Battery Board Model : IS-BT-01

* 1 board included in the introduction sample kit.

5-1 Performance


Compatible Battery CR2032 or BR2032

5-2 Appearance Specification


External Dimension 43(W) x 50(H) x 11.8(D)mm*1

Weight 20g or less*2

*1. Solder side lead measurement and error margin are not included. Please refer to the outline diagram for

details.

*2. Battery not included.

5-3 Environment Specification


Ambient Operating Temperature 0 to 50℃

Ambient Storage Temperature -20 to 70℃

Ambient Operating Humidity 10 to 80%RH


Ambient Storage Humidity 10 to 80%RH


Dust 0.1mg/m2 or less (conductive dust prohibited.)

Corrosive Gas Prohibited

IS701-3SSN2-001 REV : A

Model

Revision

- 20 - 14A4A2-00089E-3

5-4 Compliances

1) RoHS Directives

Complies with the RoHS Directives of EU.

5-5 External Interface

1) Interface for Connecting with Unit


Model : IL-2P-S3EN2-1(JAE) equivalent

Pin No. Signal

1 +

2 -

* Connect to InfoSOSA unit.

6. Battery Specifications

5.7”

RTC can be backed up by connecting a battery.

* One battery included in the introduction sample kit.

6-1 Specifications


Model CR2032

Nominal Voltage 3V

Nominal Capacity 220mAh

External Dimension φ20 x 3.2mm

Weight 5g or less

Standard RoHS Directives compliant

- 21 - 14A4A2-00089E-3

7. Cable Specifications

7-1 Power Cable

3.5”/ 4.3”/ 5.7”

* 1 cable included in the introduction sample kit.

・ Model : ISCBL-S01-001

・ Housing : PAP-02V-S(JST)

・ Contact Pin : SPHD-002T-P0.5

・ Schematic

7-2 Communication Cable for SIO 1

3.5”/ 4.3”/ 5.7”

* 1 cable included in the introduction sample kit.


・ Housing : PHR-5 (JST)

・ Contact Pin: SPH-002T-P0.5S

・ Dsub : Dsub 9 Pin Female type (Screw for installing: No4-40UNC inch screw)

・ Schematics

7-3 Battery Cable

5.7”

* One cable included in introduction sample kit.


・ Housing : IL-2S-S3L-(N)(JAE)

・ Contact Pin : IL-C2-1-10000

・ Schematics

1

2

Red

Black

Housing Side

1

2

3

4

5

3

2

5

8

7

Housing Side Dsub Side

1

2

1

2

Housing Housing

- 22 - 14A4A2-00089E-3

7-4 Power Cable (for AC Adaptor)

3.5”/ 4.3”/ 5.7”

* One cable included in introduction sample kit.

・ Housing : PAP-02V-S(JST)

・ Contact Pin : SPHD-002T-P0.5

・ DC Jack

・ Compliant plug type: φ5.5 x 2.1

・ Schematics

8. AC Adaptor Specification

3.5”/ 4.3”/ 5.7”

* One adaptor included in introduction sample kit.


Input Voltage 100-240V AC

Output Voltage 5V DC 2A

Polarity Center plus

Plug Type φ5.5 x 2.1

9. Developing Environment

Editing Screens of InfoSOSA is possible by using our development tool that we provide.

9-1 Development Tool

3.5”/ 4.3”/ 5.7”

InfoSOSA Screen Editor Software: InfoSOSA Builder (IS-BUILDER)

Screen data can be registered to the FlashROM equipped in the InfoSOSA Builder.

The maximum number of screens that can be registered to the parts that structure the screen change.

* When using image files, please use ones that were created by individual users.

Using and distributing, without permission, files protected by the copyright is strictly prohibited by law.

Please note some free materials might have using restrictions

Seedsware will not be held responsible for any troubles that may have occurred due to the copy right of

the image files.

* Please refer to the “InfoSOSA Builder Operation Manual” for more details.

1

2

Center

Ground

Housing side DC Jack side

- 23 - 14A4A2-00089E-3

10. Mounting the Unit

10-1 Mounting Conditions

3.5”/ 4.3”/ 5.7”

・ When mounting, be sure to have enough room between the unit, structure and part and also

consider the operation temperature.

・ Be sure that the ambient operating temperature and the ambient humidity are within their

designated ranges.

(Ambient operating temperature indicates the temperature of both the display side and inside

the cabinet.)

10-2 Mounting

3.5”/ 4.3”/ 5.7”

・ When mounting the unit, design the chassis referring to the panel opening examples and the

attached outline diagrams.

・ Design the chassis so that there is no distortion or twisting.

・ If using the design sheet key, you will need an opening for the tail matching the design sheet.

Display

side

Inside the

cabinet

- 24 - 14A4A2-00089E-3

10-3 Panel Opening Example

3.5” Open Frame

Below is the panel opening dimension example for when applying sheets and etc. to the surface by

opening the entire touch screen surface.

Design the chassis accordingly to the actual installing method.

*Diagram from the front side of panel (panel thickness: 1.6mm or less).

Center of Display

2×2-φ 3 Half punch h=0.5

Convex surface(Opposite side also)

2×2-M3 (Opposite side also)

Screw depth 5mm or less

Mounting Panel

- 25 - 14A4A2-00089E-3

4.3” Open Frame





* To avoid damage to the design sheet key tail, do not directly come in contact with the edge of the panel

opening. If damaged, it may cause a switch or the LED performance defect.

Center of Display

Opening for design sheet key tail

4-M3×10 Studs (Convex backside)

Burrs prohibited on welded surface

- 26 - 14A4A2-00089E-3

5.7” QVGA Open Frame







Opening for design sheet

key tail

Display center



- 27 - 14A4A2-00089E-3

5.7” VGA Open Frame









Center of Display

Opening for design sheet

key tail

- 28 - 14A4A2-00089E-3

11. Warranty

11-1 Warranty Period

3.5”/ 4.3”/ 5.7”

The warranty period is limited to12 months (1 year) from the date of shipment. Warranty for any repair needed to

the same repaired part of the same product is three months. Any defects that occur upon normal use under

conditions specified herein will be repaired (factory repair) free of charge.

Any defected parts under proper use will be examined by the supplier and replaced by the new parts if the defect

is considered to be caused by the supplier.

The replacement is subject to be included in the next lot.

11-2 Warranty Exceptions

You will be liable for all repair fees even within the warranty period for any conditions listed below:

(1) Any malfunctions, defects, and/or damages that occurred during transport, transfer, or mishandling by the user

after delivery

(2) Any malfunctions, defects, and/or damages caused by natural or man-made disaster.

(3) Any malfunctions and damages caused by static electricity.

(4) If the product is used under any condition, in any environment, or by any method other than those specified in

the specifications, catalogs, manuals, notes, and/or other documents.

(5) Any replacement of consumables.

(6) Any malfunctions, defects, and/or damages caused by associated equipment and/or usage of inappropriate

consumables and media.

(7) If the product is repaired, remodeled, modified, or disassembled by a party other than Seedsware

(8) If the product cannot be identified by a serial number.

(9) Any malfunctions, defects, and/or damages that are to have been caused on your behalf.

This warranty covers only the product itself. Any damages, on-site repairs and replacement driven by the failure of

the product will be decided upon discussion by both parties as necessary.

This product is structurally not repairable. All damaged parts are subject for replacement and freight will be charged.

12. Production Discontinuance

3.5”/ 4.3”/ 5.7”

In the event of production discontinuance, an announcement will be made on our website six months prior to the

last possible order reception date.

- 29 - 14A4A2-00089E-3

13. Others

For comments or inquiries, feel free to contact us via e-mail or phone.

*Product, specification and/or anything noted are subject to change for improvement without prior notice.

By Phone

+1-630-832-0438

By E-mail

[email protected]

FAQ

www.seedsware.co.jp/global/support/faq/

3rd Edition August, 2016

USCO America Inc.

136 W. Valletts Street, Elmhurst, IL 60126 USA

Phone: 630-832-0438/510-931-9046

E-mail: [email protected]

Business hours: 9:00a.m.～5:45p.m. (Central Time)

http://uscoamerica.com/

This document is protected by copyright law. Photocopying, duplicating, reproducing, and modifying of this product or

document in part or by whole is prohibited.

http://www.seedsware.co.jp/global/support/faq/

http://uscoamerica.com/

1 2 3 4 5 6 7 8

A

B

C

D

E

製図日

ISSUED

製図

DRAWN

承認

APPROVED

検図

CHECKED

設計

DESIGNED

部署

SECTION

尺度

SCALE

Technical Dept.

図名

TITLE

単位

UNIT

mm

製品名

MODEL

CAD登録名

CAD FILE NAME

図番

DWG No.

A3

IS701-3SSN2-001

OUTLINE

10K001_IS701-3_OUTLINE

株式会社　シーズウェア

ﾍﾟｰｼﾞ

PAGE

1 /1

2016,08,18

SM3-001683-11

1:1

RoHS対応品

RoHS compliant

S.YoshimotoS.YoshimotoT.OkadaH.Tsuji

*ｺﾈｸﾀ挿抜のため40mm以上確保願います。

Be sure to have 40mm or more space to be able to

insert and remove connector.

TP ACTIVE AREA

(71.1×53.5)

SYM

改訂日

DATE

2014,08,04 新規図面登録

DESCRIPTION

改訂内容

PAGE

ページ担当

DESIGNED

－ M.Mitani

注意ｼｰﾙ

Caution Label

LCD ACTIVE

AREA CENTER

70

52.92 (LCD ACTIVE AREA)

63.9`0.5 (LCD Outline)

88

76.9`0.5

(LCD Outline)


(38.8)

34.5

38.1

22`2

40以

上 *

40 or more

2×2-M3(対面共)

ﾈｼﾞ侵入深さ5mm以下

2×2-M3(both sides)

Screw depth shall be 5mm or less

2×2-φ3ﾊｰﾌﾊﾟﾝﾁ h=0.5

凸面表面(対面共)

2×2-φ3 Half punch h=0.5

Convex side surface (both sides)

5.8

13.3

45

15.5`0.5

60

製品銘板ｼｰﾙ

(板金側面)

Product Label

(Sheet metal side)

ｼﾘｱﾙNoｼｰﾙ

Serial No. Label

ｼﾘｱﾙｲﾝﾀﾌｪｰｽ

Serial Ports

(SIO1)


Serial Ports

(SIO2)

電源ｺﾈｸﾀ

Power Connector

社内調整用ｺﾈｸﾀ

Connector for

internal adjusting


Connector for

internal adjusting

2

565 (Board Outline)

2

2

80 (Board Outline)

14.25

17.25

14.3

2016,08,18

英語併記

English added

－ S.Yoshimoto1

NOTES

1. 指示なき寸法公差は一般寸法公差とする。

Tolerance shall be of general dimensional tolerance unless specified otherwise.

2. SIO2は、ｽﾀﾝﾀﾞｰﾄﾞﾓﾃﾞﾙのみ対応。ｼﾝﾌﾟﾙﾓﾃﾞﾙでは使用できません。

SIO2 is compliant to standard model only; cannot be used for simple model.

3. 社内調整用ｺﾈｸﾀは、お客様での使用はございません。

Connector for internal adjustment; cannot be used by customer.

寸法許容差 TOLERANCE

呼び寸法

Nominal Dimensions

L≦3

10＜L≦18

18＜L≦30

6＜L≦10

30＜L≦50

±0.4

±0.58

±0.7

±0.84

±1.0

±0.483＜L≦6

50＜L≦80

80＜L≦120

120＜L≦180

180＜L≦250

250＜L≦315

315＜L≦400

400＜L≦500

±1.2

±1.4

±1.6

±1.85

±2.1

±2.3

±2.5

1 2 3 4 5 6 7 8

A

B

C

D

E

製図日

ISSUED

製図

DRAWN

承認

APPROVED

検図

CHECKED

設計

DESIGNED

部署

SECTION

尺度

SCALE

Technical Dept.

図名

TITLE

単位

UNIT

mm

製品名

MODEL

CAD登録名

CAD FILE NAME

図番

DWG No.

A3

IS711-4SSN3-001

OUTLINE



ﾍﾟｰｼﾞ

PAGE

1 /1

2016,08,18

SM3-001420-12

1:1

RoHS対応品

RoHS compliant


TP ACTIVE AREA

(95.04×53.86)

SYM

改訂日

DATE

2013,06,20 新規図面登録

DESCRIPTION

改訂内容

PAGE

ページ担当

DESIGNED

－ M.Mitani

注意ｼｰﾙ

Caution Label

53.86(LCD ACTIVE AREA)

95.04(LCD ACTIVE AREA)

n4

4

-

139

105.5 (LCD Outline)

73

67.2(LCD Outline)

(40)

36.07

LCD ACTIVE AREA

CENTER

60`0.3

9.1

132`0.5

22.6`2

(ﾀｯﾁﾊﾟﾈﾙ無)

24.1`2

(ﾀｯﾁﾊﾟﾈﾙ有

)

(25.5)

4.5

ｼｰﾄｷｰｲﾝﾀﾌｪｰｽ

(ｽｲｯﾁ側)

Sheet Key Interface

(for Switch)


(LED側)

Sheet Key Interface

(for LED)


Serial No. Label

電源ｺﾈｸﾀ

Power Connector


Serial Ports

(SIO2)


Serial Ports

(SIO1)


(板金側面)

Product Label

(Sheet metal side)


Connector for

internal adjusting

5.3

5.25

11

65 (Board Outline)

5.3

115 (Board Outline)

15.5

18.5

17

22 13


呼び寸法

Nominal Dimensions

L≦3

10＜L≦18

18＜L≦30

6＜L≦10

30＜L≦50

±0.4

±0.58

±0.7

±0.84

±1.0

±0.483＜L≦6

50＜L≦80

80＜L≦120

120＜L≦180

180＜L≦250

250＜L≦315

315＜L≦400

400＜L≦500

±1.2

±1.4

±1.6

±1.85

±2.1

±2.3

±2.5

2015,03,16 NOTES 一部削除、寸法削除－ M.Mitani1

2016,08,18

英語併記

English added

－ S.Yoshimoto2

NOTES



2. ﾀｯﾁﾊﾟﾈﾙ有の場合、製品型式は IS711-4SSxx-xxxになります。

ﾀｯﾁﾊﾟﾈﾙ無の場合、製品型式は IS711-4NSxx-xxxになります。



(仕様は予告なく変更になる場合がございます。)

1

1

1

1

1 2 3 4 5 6 7 8

A

B

C

D

E

製図日

ISSUED

製図

DRAWN

承認

APPROVED

検図

CHECKED

設計

DESIGNED

部署

SECTION

尺度

SCALE

Technical Dept.

図名

TITLE

単位

UNIT

mm

製品名

MODEL

CAD登録名

CAD FILE NAME

図番

DWG No.

A3

IS701-5SSN1-001

OUTLINE



ﾍﾟｰｼﾞ

PAGE

1 /1

2016,08,18

SM3-001551-11

1:2

RoHS対応品

RoHS compliant


SYM

改訂日

DATE

2013,05,08 新規図面登録

DESCRIPTION

改訂内容

PAGE

ページ担当

DESIGNED

－ S.Yoshimoto


呼び寸法

Nominal Dimensions

L≦3

10＜L≦18

18＜L≦30

6＜L≦10

30＜L≦50

±0.4

±0.58

±0.7

±0.84

±1.0

±0.483＜L≦6

50＜L≦80

80＜L≦120

120＜L≦180

180＜L≦250

250＜L≦315

315＜L≦400

400＜L≦500

±1.2

±1.4

±1.6

±1.85

±2.1

±2.3

±2.5

2016,08,18

英語併記

English added

－ S.Yoshimoto1

注意ｼｰﾙ

Caution Label

LCD ACTIVE

AREA CENTER

160

116.2 (TP ACTIVE AREA)




130.32`0.5

(LCD Outline)


115

n4

4-

17

153`0.5

92`0.5

(63)

53.65

(4.5)

21.5

`2


(ｽｲｯﾁ用)

Sheet Key Interface

(for Switch)


(LED用)

Sheet Key Interface

(for LED)

電源ｺﾈｸﾀ

Power Connector


(板金側面)

Product Label

(Sheet metal side)


Serial No. Label

ﾊﾞｯﾃﾘｲﾝﾀﾌｪｰｽ

Battery


Serial Ports

(SIO1)


Serial Ports

(SIO2)


Connector for

internal adjusting

1.3

1 1

100 (Board Outline)

130 (Board Outline)

10

40

14.5

14

10

20

2216

27

NOTES





1 2 3 4 5 6 7 8

A

B

C

D

E

製図日

ISSUED

製図

DRAWN

承認

APPROVED

検図

CHECKED

設計

DESIGNED

部署

SECTION

尺度

SCALE

Technical Dept.

図名

TITLE

単位

UNIT

mm

製品名

MODEL

CAD登録名

CAD FILE NAME

図番

DWG No.

A3

IS701-5SSN1-101

OUTLINE



ﾍﾟｰｼﾞ

PAGE

1 /1

2016,08,18

SM3-001550-12

1:2

RoHS対応品

RoHS compliant


SYM

改訂日

DATE

2013,05,08 新規図面登録

DESCRIPTION

改訂内容

PAGE

ページ担当

DESIGNED

－ M.Mitani


呼び寸法

Nominal Dimensions

L≦3

10＜L≦18

18＜L≦30

6＜L≦10

30＜L≦50

±0.4

±0.58

±0.7

±0.84

±1.0

±0.483＜L≦6

50＜L≦80

80＜L≦120

120＜L≦180

180＜L≦250

250＜L≦315

315＜L≦400

400＜L≦500

±1.2

±1.4

±1.6

±1.85

±2.1

±2.3

±2.5

2015,05,25 NOTES 一部削除、寸法削除－ M.Mitani1

2016,08,18

英語併記

English added

－ S.Yoshimoto2

LCD ACTIVE

AREA CENTER



144`0.5

(LCD Outline)


n4

4-


109`2


164`2

55.5

(58)

92`0.5

12

157`0.5

29.3`2 (ﾀｯﾁﾊﾟﾈﾙ無)

30.9

`2 (ﾀｯﾁﾊﾟﾈﾙ付

)

1.2

3.3

(1.6)


Serial No. Label


(板金側面)

Product Label

(Sheet metal side)


(LED用)

Sheet Key Interface

(for LED)


(ｽｲｯﾁ用)

Sheet Key Interface

(for Switch)


Serial Ports

(SIO2)


Connector for

internal adjusting

ﾊﾞｯﾃﾘｲﾝﾀﾌｪｰｽ

Battery

電源ｺﾈｸﾀ

Power Connector


Serial Ports

(SIO1)

3.3

1

100 (Board Outline)

130 (Board Outline)

1

4.8

10

47.5

11.5

10

22

27

16

1

NOTES



2. ﾀｯﾁﾊﾟﾈﾙ有の場合、製品型式はIS701-5SSN1-101になります。

ﾀｯﾁﾊﾟﾈﾙ無の場合、製品型式はIS701-5NSN1-101になります。



1

1

Documents

Product Specification - USCO America