Product Information

INDEX

COMPANY INTRODUCTION

CENTRIFUGAL PUMP

DEEP WELL TURBINE PUMP

4” SUBMERSIBLE PUMP





4” , 6” , 8” , 10” SUBMERSIBLE MOTOR

3 PHASE MOTORS FOOT MOUNTED

ASE FRAME AND COUPLING

GASOLINE /PETROL GENERATORS

OPEN TYPE DIESEL GENERATORS

SOUND PROOF/WEATHER PROOF DG SET

TRAILER MOUNTED DG SET

CANOPIES FOR DG SET

ATS/MCU

ACCESSORIES

TUBE WELL DRILLING

OTHERS

Centrifugal Pump

Fields of Application

Water supply

Fire-fighting systems

Sprinkling

Irrigation

Drainage

Heating

Air-conditioning systems

Drinking water

Service water

Hot water

Cooling water

Swimming pool water

Sea water

Fire-fighting water

Brackish water

Condensate

Brine

Oils

Cleaning agents

Operating Data

Q up to 660 m3/h, 183 l/s H up to 102 m

t -30°C to +140°C p2 up to 6 bar

Design

Horizontal volute casing pump, single-stage, with power ratings and main dimensions to EN 733, with bearing bracket, in

back pull-out design. Shaft with replaceable shaft sleeve/shaft protecting sleeve in the shaft seal area. Volute casing and

impeller with replaceable wear rings. Volute casing with integrally cast pump feet.

Coupling

Flexible coupling with/without spacer sleeve

Contact Guard

coupling guard as per EN 294.

Base plate

Sectional steel / folded steel plate

for the complete unit (pump and motor)

in torsion-resistant design

Bearings

Deep-groove ball bearings, grease-lubricated

Shaft Seal

Mechanical seal to DIN 24 960 or gland packing.

Due to continuous efforts in improvements, information furnished above is subject to change without notice

DEEP WELL TURBINE PUMP

Application:

These pumps are suitable for water supply schemes, Irrigation schemes, lowering of ground water level and dewatering of mines and construction sites. Deep well turbine pumps particularly suitable for barrow bore holes. Minimum bore sizes hole sizes range form 200mm to 675mm.

Operating Data:-

Capacity Q up to 2600 m3/hr

Head H up to 160 m

Speed n up to 3500 RPM

Temperature t up to 105 C

Suspended Depth up to 120 m

Design:-

Main pump components are the pump bowl Assembly , column and shaft assembly, and the

discharge head assembly. Single or multistage radically split, interchangeable intermediate bowls.

Interchangeable lengths of the column assembly and variable setting depth.

Wet Pit Installation

In normal operation, the pump body is submerged and suspended in the fluid pumped,

supported by the discharge head.

Dry Pit Installation:-

The pump can also be installed in dry pits. For this purpose a foot cum elbow are fitted in the

suction pipe, thus enabling the pump to be connected to the source. An adapter piece is also

provided to cater for the possibility of expansion in the axial direction, when the temperature

fluctuates.

Drives:-

DWT pumps are driven either by the vertical hollow/solid shaft electric motor or a diesel (IC)

engine. If an IC engine is used as a drive the drive transmission can be affected via bevel gears. A

torsion ally flexible card an shaft is fitted as a coupling in this case.



SINGLE PHASE & THREE PHASE

Multistage submersible borehole pumps made of stainless

steel and plastics for well diameters as from 100 mm (4 inch)

available with single-phase a.c. and three-phase current

motors with short cable. Applications: domestic water supply

irrigation and spray irrigation, lowering ground water levels

fire protection systems, cooling circuits, as well as fountain,

pressure boosting and air-conditioning systems.

SINGLE PHASE SUBMERSIBLE PUMP DISCHARGE IN m³/hr. HEAD IN METER

Type KW/hp 1.1 1.6 2 2.5 2.8

2C/7 0.37/0.5

0.55/0.75

34 30 27 20 13

2C/10 0.55/0.75 49 44 38 29 19

2C/11 0.75/1.0 55 49 42 32 21

2C/13 0.75/1.0 65 57 50 38 25 2C/15 0.75/1.0 74 66 58 43 29

2C/18 1.0/1.5 89 79 69 52 35 2C/21 1.0/1.5 104 92 81 60 40

2C/23 1.1/1.5 113 101 88 66 44

2C/25 1.1/1.5 122 109 95 71 48

2C/27 1.5/2 132 118 103 77 51

2C/30 1.5/2 147 131 114 86 57

2C/33 2.2/3.0 159 142 124 93 62

2C/38 2.2/3.0 186 165 145 109 72

2C/45 2.2/3.0 217 193 169 127 85


SINGLE PHASE SUBMERSIBLE PUMP DISCHARGE IN m³/hr. Head in meter

1C/7 0.37/0.5 34 29 27 21 14

1C/10 0.37/0.5 49 42 38 30 20

1C/13 0.55/0.75 64 55 50 39 26

1C/15 0.55/0.75 74 64 58 45 31

1C/18 0.55/0.75 89 76 69 54 37

1C/21 0.75/1.0 104 90 81 64 43 1C/25 0.75/1.0 124 107 97 76 52

4” SINGLE & THREE PHASE PUMP

SINGLE PHASE PUMPS

SINGLE PHASE SUBMERSIBLE PUMP -DISCHARGE HEAD IN m³/hr, HEAD IN METER

Type KW/HP 2 3 4 5 6 4C/5 0.37/0.5

0.55/0.75

29 27 24 20 14

4C/6 0.55/0.75 0.72/1.0

34 32 29 24 17

4C/8 0.75/1.0 46 43 38 32 23 4C/10 1.1/1.5 52 48 43 36 26

4C/12 1.1/1.5 69 64 57 48 34

4C/15 1.5/2.0 86 80 71 60 43 4C/17 2.2/3.0 97 91 81 68 49

4C/19 2.2/3.0 109 101 90 76 54 4C/23 2.2/3.0 130 122 109 91 65

SINGLE PHASE SUBMERSIBLE PUMP-DISCHARGE HEAD IN m³/hr, HEAD IN

METER Type KW/hp

4 5 6 7 8

7C/5 0.75/1.0 29 27 25 23 20

7C/7 1.1/1.5 40 38 35 32 28

7C/10 1.5/2.0 57 53 50 46 40

7C/12 2.2/3.0 68 63 59 54 47

7C/13 2.2/3.0 73 68 63 59 51

SINGLE PHASE PUMP - DISCHARGE HEAD IN m³/hr , HEAD IN METER

Pump Type

KW/H

P

9 12 16 20 22

18C/4 1.5/2.0 1.1/1.5

19 17 14 11 10

18C/5 1.5/2.0 24 21 18 14 12

18C/6 2.2/3.0 28 25 21 17 14

18C/7 2.2/3.0 33 30 25 20 16

3 PHASE SUBMERSIBLE PUMP Discharge in m³/hr, HEAD IN METERS

TYPE KW/HP 0.5 1.2 2.0 2.5 3.0

2C/11 0.75/1.0 60 51 43 32 21

2C/13 0.75/1.0 71 61 51 38 25

2C/15 0.75/1.0 82 70 58 44 29

2C/18 1.1/1.5 96 82 69 51 34 2C/21 1.1/1.5 112 96 80 60 40

2C/23 1.1/1.5 123 105 88 66 44 2C/25 1.1/1.5 133 114 95 71 48

2C/27 1.5/2.0 144 124 103 77 51

2C/30 1.5/2.0 160 137 114 86 57

2C/33 2.2/3.0 175 150 125 94 63

2C/38 2.2/3.0 202 173 144 108 72

2C/45 2.2/3.0 239 205 171 128 85

2C/50 3.0/4.0 259 222 185 139 93

4” SINGLE & THREE PHASE SUBMERSIBLE PUMP

THREE PHASE PUMP 3 PHASE SUBMERSIBLE PUMP- HEAD IN METERS, DISCHARGE IN m₃/hr Pump Type KW/HP 0.5 0.8 0.9 1.1 1.3

1C/7 0.75/1.0 35 30 27 21 15

1C/10 0.75/1.0 50 43 39 31 21

1C/12 0.75/1.0 65 56 51 40 27

1C/15 0.75/1.0 75 65 58 46 30

1C/18 0.75/1.0 90 77 70 55 37

1C/21 0.75/1.0 105 90 82 64 44

1C/21 0.75/1.0 105 90 82 64 44

1C/25 0.75/1.0 125 108 97 76 52

1C/30 0.75/1.0 150 129 117 92 62

1C/35 1.1/1.5 171 147 133 105 71

1C/40 1.1/1.5 196 168 152 120 82

1C/50 1.5/2.0 245 211 191 150 102

3 PHASE SUBMERSIBLE PUMP - DISCHARGE IN m³/hr, HEAD IN METERS

Type KW/hp 0.5 1.2 2.0 2.5 3.0

4C/6 0.75/1.0 34 32 28 25 18

4C/8 0.75/1.0 45 43 38 33 23

4C/10 1.1/1.5 56 53 47 40 29 4C/12 1.1/1.5 67 64 56 49 35

4C/15 1.5/2.0 84 79 70 61 43

4C/17 2.2/3.0 95 90 79 69 49

4C/19 2.2/3.0 107 100 88 77 55

4C/23 2.2/3.0 129 121 107 93 66 4C/25 3.0/4.0 139 131 115 100 71

4C/30 3.7/5.0 166 156 137 119 85

4C/35 3.7/5.0 194 182 160 139 100

4C/40 3.7/5.0 221 209 183 159 114

4” SINGLE & 3 PHASE SUBMERSIBLE PUMP

THREE PHASE PUMP

3 PHASE SUBMERSIBLE PUMP- DISCHRAGE IN m³/hr, HEAD IN METERS

Type KW/HP 4 5 6 7 8

7C/5 0.75/1.0 29 27 25 23 20

7C/7 1.1/1.5 40 37 35 32 28

7C/10 1.5/2.0 57 53 50 46 40

7C/12 2.2/3.0 68 64 59 55 48

7C/15 2.2/3.0 85 80 74 68 60

7C/19 3.0/4.0 106 99 92 84 74

7C/22 3.7/5.0 122 114 106 97 85

7C/25 3.7/5.0 138 129 120 111 97

7C/31 4.5/6.0 176 164 152 141 123

3 PHASE SUBMERSIBLE PUMP - DISCHRAGE IN m³/hr, HEAD IN METERS

Type KW/hp 6 8 1

0

12 14

12C/10 2.2/3.0 57 51 43 33 23

12C/13 3.0/4.0 74 67 55 43 30

12C/17 3.7/5.0 94 85 71 55 38

12C/21 4.5/6.0 116 105 87 68 47

3 PHASE SUBMERSIBLE PUMP - DISCHRAGE IN m³/hr, HEAD IN METERS

Type KW/hp 9 12 15 18 22

18C/6 1.5/2.0 29 27 22 17 14

18C/7 2.2/3.0 33 31 25 20 17

18C/9 3.0/4.0 42 39 32 25 21

18C/10 3.0/4.0 46 43 35 28 23

18C/11 3.7/5.0 51 47 39 30 25

18C/12 3.7/5.0 55 52 42 33 28

18C/13 4.5/6.0 61 57 47 37 31

18C/14 4.6/6.0 66 62 51 40 33


Application:-

Domestic and general water supply duties.

Irrigation and sprinkling systems

Ground water pumping

Cooling water circulation

Pressure boosting plants

Air Conditioning systems

Fountain etc.

Pump Construction / Design:-

Single or multistage, single entry centrifugal pumps of ring section type with radial or mixed flow

impellers. Radial impellers are with renewable/integral diffusers and mixed flow impellers with

stage bowl. The plain bearings are water lubricated. Suction strainer fitted on suction casing

prevents ingress of coarse impurities. Higher stage pumps are fitted with intermediate bearing.

The axial thrust is balanced by thrust bearing in the motor.

Operating data ( 50 Hz )

Capacity Q up to 70 m³/hr.

Head H up to 300m.

Max. Power Required p up to 18.5 kw

Temp of liquid pumped t 30°C

Nominal Speed n 2900 rpm

Bearing & Lubrication:-

Radial-plain bearings are lubricated by the pumped water. Depending on no. of stages:

additionally one intermediate bearing is used in the pump.

The axial thrust is carried by the thrust bearing in motor.

Direction of Rotation & operational speed:-

Clockwise when viewed from the drive shaft end.

The pump performance curves are drawn from a standard sped of 2900 rpm. While

referring to these curves the required duty point should be converted to the actual

speed of the motor selected.

Model:

UQ 2100-4 Head up to 150 feet Motor: 5 Hp

UQ 2100-5 Head Up to 190 feet Motor: 5 HP

UQ 2100-6 Head up to 230 feet Motor: 6 HP

UQ 2100-7 Head Up to 275 feet Motor: 7.5 HP

UQ 2100-8 Head Up to 310 Feet Motor: 10 HP


UQ 2100-12 Head Up to 500 feet Motor: 12.5 HP

UQ 2100-14 Head Up to 610 Feet Motor: 15HP

UQ 2100-17 Head Up to 660 feet Motor:17.5 HP

UQ 2100-18 Head Up to 700 feet Motor:17.5 HP

UQ2100-20 Head Up to 730 feet Motor: 20 HP









Fountain etc.









Head H up to 300m.










The pump performance curves are drawn from a standard sped of 2900 rpm. While referring to

these curves the required duty point should be converted to the actual speed of the motor

selected.

Model:

BP 2400-4 Head Up to 160 feet Motor: 5 HP


BP 2400-6 Head Up to 240 feet Motor: 7.5 HP








Application:-







Fountain etc.









Head H up to 300m.













Model:






BP 3000-8 Head Up to 280 feet Motor: 17.5 / 20 HP




6” SUBMERSIBLE Pump

Application:-







Fountain etc.









Head H up to 300m.













Model:

BP 3200-1D Head Up to 72 feet Motor: 7.5 HP

BP 3200-2B Head Up to 90 feet Motor: 7.5 HP

BP 3200-3D Head Up to 110 feet Motor: 10 HP

BP 3200-3A Head Up to 130 feet Motor: 10 HP

BP 3200-3C Head Up to 145 feet Motor: 12.5 HP

BP 3200-4B Head Up to 180 feet Motor: 15 HP

BP 3200-4C Head Up to 196 feet Motor: 17.5 HP

BP 3200-5C Head Up to 250 feet Motor: 20 HP

BP 3200-6C Head Up to 290 feet Motor: 25 HP

This 4" submersible motors has been designed and

produced according to the market requirement. In design

and material selection all efforts have been made to offer a

product to our customers which stand for reliability,

excellent quality, long and trouble free life.

Technical specification

Motor casing: AISI 304 stainless steel.

Shaft: AISI 304 stainless steel.

Bottom: AISI 304 stainless steel.

Shaft coupling: according to Nema Standard.

Bearings: axial and radial thrust ball bearings.

Seal: graphite/ceramic mechanical seal.

Rubber diaphragm: over size rubber diaphragm

allows water volume regulation inside the motor,

according to external pressure

and operating temperature.

Upper bracket: high resistance cast iron nickel

plated .

Filling fluid: special fluid, for a better lubricant effect,

increase life of moving parts.

Connection: removable cable connector.

Degree of protection: IP 58

Insulation class: F

Voltage tolerance: +6% / -10%

Mounting position: horizontal up to 2,2 kW

Minimum flow rate speed: 0,8 m/s

Maximum deep head: 150 m

Water temperature: 35°C maximum

Starting per hour: 30

4” SUBMERSIBLE MOTORS

6” SUBMERSIBLE MOTORS

This 6" submersible motors has been designed and produced

according to the market requirement. In design and material

selection all efforts have been made to offer a product to our

customers which stand for reliability, excellent quality, long and

trouble free life. 6" submersible motors are asynchronous three

phase, with squirrel cage and wet type rewind able stator.


Winding: made of pure electrolytic copper wire sheeted with a

non-hygroscopic PVC, very strong for high temperature.

Stator: with low-loss magnetic sheet, fixed into a casing

stainless made.

Rotor: only with copper bars.

All rotors are dynamically balanced for smooth and vibration

free operation.

Shaft: AISI 420 stainless steel made, is oversized designed

to assure stiffness.

Shaft coupling: according to Nema Standard.

Shaft bearing: upper and lower double bronze bearings.

Thrust bearing: thrust sliding block bearing, self aligning

Mitchell type, suitable for 15500 N axial thrust.

Seal: silicon carbide mechanical seal for normal and

sandy wells.

Rubber diaphragm: together with upper inside and outside

filters, allows water volume regulation inside the motor,

according to external pressure and operating temperature.

Brackets: high resistance nickel plated cast iron for

upper and lower brackets.

Filling fluid: special water, developed for motor's

corrosion inside parts prevent and excellent cooling quality.


Voltage tolerance: +6% / -

10%

Mounting position: vertical /

horizontal

Minimum flow rate speed: 0,3 m/s


Water temperature: 30°C

maximum


8” , 10 “ SUBMERSIBLE MOTOR

These 8", 10” submersible motors has been designed and

produced according to the market requirement. In design and

material selection all efforts have been made to offer a product to

our customers which stand for reliability, excellent quality, long and

trouble free operation. 8" submersible motors are asynchronous

three phase, with squirrel cage and wet type rewind able stator.


Winding: made of pure electrolytic copper wire sheeted with a

non-hygroscopic PVC, very strong for high temperature.

Stator: with low-loss magnetic sheet, fixed into a casing

stainless made.

Rotor: only with copper bars. All rotors are dynamically balanced

for smooth and vibration free operation.

Shaft: SS 420, oversized designed to assure stiffness.

Shaft coupling: 8" NEMA Standard.

Shaft bearing: upper and lower double bronze bearings.

Thrust bearing: thrust sliding block bearing, self aligning

Mitchell type, suitable for 45000 N axial thrust.

Seal: silicon carbide for normal and sandy wells.

Rubber diaphragm: together with upper inside and outside

filters, allows water volume regulation inside the motor,

according to external pressure and operating temperature.

Brackets: high resistance nickel plated cast iron for

upper and lower brackets.

Filling fluid: special water.


Voltage tolerance: +6% / -10%

Mounting position: vertical ~

Minimum flow rate speed: 0,2 m/s (30~52kw)

0,5 m/s (55 93kw)


Water temperature: 30°C maximum


3 PHASE STANDARD MTORS

General description

Increasing energy costs mean that energy consumption is of increasing significance

in drive technology. It is essential to fully exploit potential for minimizing these

costs in order to remain competitive now and in the future. Lower energy

consumption also benefits the environment.

It is against this background that we are developing a new generation of low-

voltage motors, enabling you to do more with your motors. Innovative copper

rotors create the very best basis for highly efficient motors. The new motors for IE2

(high efficiency) thereby offer large energy savings and are better for the

environment. Also, the modular design concept provides full flexibility: each motor

is based on a standardized concept for all international markets.

Technical data overview ( Foot Mounted )

Totally Enclosed Fan cooled squirrel cage induction motors as per DIN VDE

0530/IEC 34-1

3 Phase 400 VAC , 50 Hz

Suitable for VFD Operation

Ambient Temperature 40 °C , Altitude 1000 m above sea level, Construction

IM B3 ( Foot Mounted) ,

Degree of Protection IP 55 , Insulation Class ‘F’

Power Range : 1 KW to 100 Kw , Pole 2, 4, 6

Technical data overview (Vertical hollow shaft motors ) Totally enclosed fan cooled squirrel cage vertical hollow shaft

induction motors as per DIN VDE 0530 / IEC 34—1

3 Phase 400 VAC , 50 Hz, Ambient Temperature 40 °C , Altitude 1000 m

above sea level, Construction IMV1 ( flange mounted ) with NEMA Flanges

Degree of protection IP 44 , Insulation Class “ F “ , Motors are protected

with PTC Thermistators which protect the windings against excessive

heating under changing load conditions.

Power Range: 7.5 KW to 75 KW

Pole 2 , 4

GASOLINE/PETROL GENERATORS

Rated Output 1.3 kVA

Consumption 0.97 litre / hour

Tank Capacity 3.7 litres

Engine GX160

Noise Level 66 dB

Dry Weight 33 kg

Rated Output 2 kVA


Tank Capacity 15 litres

Engine GX160

Noise Level 65 dB

Dry Weight 45 kg

Rated Output 4 kVA



Engine GX340

Noise Level 70 dB

Dry Weight 82 kg Rated Output 5 kVA



Engine GX390

Noise Level 72 dB

Dry Weight 89 kg

Portable Standby Generators Portable standby generator units are the dependable workhorses of the field … whenever you

simply need raw power. They are easy to use, safe and reliable. Some of the standard features and benefits

include:

Features Automatic "Low-Oil-Shutdown" features to prevent damage

Circuit breaker protection to protect the unit itself as well as your devices

Full perimeter safety frame to prevent harm from hot surfaces and moving parts

Optional wheel kits to enhance portability

This rugged gasoline gen set delivers reliable power anywhere for emergency or residential standby

power, maintenance crews and light commercial applications.

Models:-

Open Type Diesel Generators

Cummins Diesel Generator Set

Introduction:-

Cummins Inc., a global power leader, is a corporation of complementary business units that design,

manufacture, distribute and service engines and related technologies since 1919, headquartered in

Columbus, Indiana(USA),Cummins serves customers in approximately 190 countries and territories through a

network of more than 500 Company-owned and independent distributor locations and approximately 5,200

dealer locations.

Genset model Engine model Prime power Standby Power

AC28 4B3.9-G1 20/25 22/27.5

AC28 4B3.9-G2 20/25 22/27.5

AC41-Ⅰ 4BT3.9-G1 30/38 33/41

AC41-Ⅱ 4BT3.9-G2 30/38 33/41

AC55 4BTA3.9-G2 40/50 44/55

AC62 4BTA3.9-G2 45/56 50/62

AC69 4BTA3.9-G2 50/63 55/69

AC110 6BT5.9-G1 80/100 88/110

AC110 6BT5.9-G2 80/100 88/110

AC138 6BTA5.9-G2 100/125 110/138

AC149 6BTAA5.9-G2 108/135 119/149

AC165 6CTA8.3-G2 120/150 132/165

AC206 6CTA8.3-G2 150/188 165/206

AC220 6CTAA8.3-G2 160/200 176/220

AC275 6LTAA8.9-G2 200/250 220/275

AC343 QSM11-G2 250/313 275/343

AC275 NT855-GA 200/250 220/275

AC275 MTA11-G2A 200/250 220/275

AC303 NTA855-G1A 220/275 242/303

AC343 MTAA11-G3 250/313 275/343

AC375 NTA855-G2A 280/344 300/375

AC413 NTAA855-G7A 300/375 330/413

AC450 NTAA855-G7A 320/400 360/450

AC500 KTA19-G3 360/450 400/500

AC625 KTAA19-G5 450/565 500/625

AC660 KTAA19-G6A 480/600 528/660

AC688 KTAA19-G6A 500/625 500/688

AC715 QSK19-G3 520/650 572/715

AC825 KTA38-G2 600/750 660/825

AC1000 KTA38-G2A 720/900 800/1000

AC1100 KTA38-G5 800/1000 880/1100

AC1238 KTA38-G9 900/1125 990/1238

AC1375 KTAA38-G9A 1000/1250 1100/1375

For complete details/specifications and big power please contact us


Perkins/Lovol Diesel Generator set

Genset

model

Engine model

Prime power

KW/KVA

Standby

Power

KW/KVA

Fuel

Consumption

≤g/kw.h

dimension

mm

Weight

kg

AP10

403D-11

7/9

8/10

248

1280×500×860

330

AP14

403D-15

10/13

11/14

248

1280×500×950

390

AP22

404D-22

16/20

18/22

237

1420×500×1000

470

AP33

1103A-33G

24/30

26/33

235

1520×650×1200

750

AP50

1103A-33TG1

36/45

40/50

235

1520×650×1200

770

AP66

1103A-33TG2

48/60

53/66

235

1520×650×1200

770

AP72

1104A-44TG1

52/65

57/72

208

1800×650×1200

840

AP88

1104A-44TG2

64/80

70/88

208

1800×650×1200

850

AP110

1104C-44TAG2

80/100

88/110

205

1850×700×1200

1120

AP150

1006TAG

108/135

120/150

208

2250×800×1280

1200

AP165

1006TAG2

120/150

132/165

208

2300×900×1560

1400

AP220

1306C-E87TAG3

160/200

176/220

207

2530×900×1560

1640

AP248

1306C-E87TAG4

180/225

198/248

201

2530×900×1560

1725

AP259

1306C-E87TAG5

188/235

207/259

203

2530×900×1560

1800

AP880

4006-23TAG3A

640/800

704/880

210

3780×1710×2200

4960

AP990

4008TAG1A

720/900

792/990

206

4800×2030×2170

7100

AP1100

4008TAG2A

800/1000

880/1100

214

4800×2030×2170

7100

AP1375

4012-46TWG2A

1000/1250

1100/1375

212

5100×2050×2400

8600

AP1650

4012-46TAG2A

1200/1500

1320/1650

200

5310×2050×2400

9500

AP1925

4016TAG

1400/1750

1540/1925

205

5900×2300×3000

14500

AP2030

4016TAG1A

1476/1845

1624/2030

205

5900×2300×3000

14500

AP2263

4016TAG2A

1646/2058

1811/2263

209

6000×2300×3000

14800


Doosan Daewoo Diesel Generators

Genset

model

Engine model

Prime power

KW/KVA

Standby

Power

KW/KVA

Fuel

Consumption

≤L/h

dimension mm

Weight kg

AD66

DB58

48/60

53/66

18.1

2100×800×1400

1100

AD96

D1146

70/88

77/96

20.8

2350×900×1300

1500

AD138

D1146T

100/125

110/138

27

2400×900×1300

1600

AD186

P086TI-1

135/169

149/186

48.4

2600×950×1450

1750

AD220

P086TI

160/200

176/220

48.4

2600×950×1450

1825

AD303

P126TI

220/275

242/303

66.2

3000×1000×1650

2200

AD344

P126TI-II

250/313

275/344

77.6

3000×1000×1650

2300

AD413

P158LE-1

300/375

330/413

102.9

3100×1390×1700

2500

AD440

P158LE

320/400

352/440

102.9

3100×1400×1800

2800

AD495

P158LE-S

360/450

396/495

109.7

3300×1400×1800

3050

Sound Proof/ Weather Proof /Trailer Mounted DG Sets

Cummins Diesel Generator set

Introduction:-

Cummins Inc., a global power leader, is a corporation of complementary business units that design,

manufacture, distribute and service engines and related technologies since 1919, headquartered in

Columbus, Indiana(USA),Cummins serves customers in approximately 190 countries and territories through a

network of more than 500 Company-owned and independent distributor locations and approximately 5,200

dealer locations.

Genset model Engine model Prime power Standby Power

AC28 4B3.9-G1 20/25 22/27.5

AC28 4B3.9-G2 20/25 22/27.5

AC41-Ⅰ 4BT3.9-G1 30/38 33/41

AC41-Ⅱ 4BT3.9-G2 30/38 33/41

AC55 4BTA3.9-G2 40/50 44/55

AC62 4BTA3.9-G2 45/56 50/62

AC69 4BTA3.9-G2 50/63 55/69

AC110 6BT5.9-G1 80/100 88/110

AC110 6BT5.9-G2 80/100 88/110

AC138 6BTA5.9-G2 100/125 110/138

AC149 6BTAA5.9-G2 108/135 119/149

AC165 6CTA8.3-G2 120/150 132/165

AC206 6CTA8.3-G2 150/188 165/206

AC220 6CTAA8.3-G2 160/200 176/220

AC275 6LTAA8.9-G2 200/250 220/275

AC343 QSM11-G2 250/313 275/343

AC275 NT855-GA 200/250 220/275

AC275 MTA11-G2A 200/250 220/275

AC303 NTA855-G1A 220/275 242/303

AC343 MTAA11-G3 250/313 275/343

AC375 NTA855-G2A 280/344 300/375

AC413 NTAA855-G7A 300/375 330/413

AC450 NTAA855-G7A 320/400 360/450

AC500 KTA19-G3 360/450 400/500

AC625 KTAA19-G5 450/565 500/625

AC660 KTAA19-G6A 480/600 528/660

AC688 KTAA19-G6A 500/625 500/688

AC715 QSK19-G3 520/650 572/715

AC825 KTA38-G2 600/750 660/825

AC1000 KTA38-G2A 720/900 800/1000

AC1100 KTA38-G5 800/1000 880/1100

AC1238 KTA38-G9 900/1125 990/1238

AC1375 KTAA38-G9A 1000/1250 1100/1375

Sound Proof/Weather Proof/Trailer Mounted DG Set

Perkins Diesel Generator Set

Genset

model

Engine model

Prime power

KW/KVA

Standby

Power

KW/KVA

Fuel

Consumption

≤g/kw.h

dimension

mm

Weight

kg

AP10

403D-11

7/9

8/10

248

1280×500×860

330

AP14

403D-15

10/13

11/14

248

1280×500×950

390

AP22

404D-22

16/20

18/22

237

1420×500×1000

470

AP33

1103A-33G

24/30

26/33

235

1520×650×1200

750

AP50

1103A-33TG1

36/45

40/50

235

1520×650×1200

770

AP66

1103A-33TG2

48/60

53/66

235

1520×650×1200

770

AP72

1104A-44TG1

52/65

57/72

208

1800×650×1200

840

AP88

1104A-44TG2

64/80

70/88

208

1800×650×1200

850

AP110

1104C-44TAG2

80/100

88/110

205

1850×700×1200

1120

AP150

1006TAG

108/135

120/150

208

2250×800×1280

1200

AP165

1006TAG2

120/150

132/165

208

2300×900×1560

1400

AP220

1306C-E87TAG3

160/200

176/220

207

2530×900×1560

1640

AP248

1306C-E87TAG4

180/225

198/248

201

2530×900×1560

1725

AP259

1306C-E87TAG5

188/235

207/259

203

2530×900×1560

1800

AP880

4006-23TAG3A

640/800

704/880

210

3780×1710×2200

4960

AP990

4008TAG1A

720/900

792/990

206

4800×2030×2170

7100

AP1100

4008TAG2A

800/1000

880/1100

214

4800×2030×2170

7100

AP1375

4012-46TWG2A

1000/1250

1100/1375

212

5100×2050×2400

8600

AP1650

4012-46TAG2A

1200/1500

1320/1650

200

5310×2050×2400

9500

AP1925

4016TAG

1400/1750

1540/1925

205

5900×2300×3000

14500

AP2030

4016TAG1A

1476/1845

1624/2030

205

5900×2300×3000

14500

AP2263

4016TAG2A

1646/2058

1811/2263

209

6000×2300×3000

14800

Sound Proof/Weather Proof/Trailer Mounted DG Set

Doosan Daewoo Diesel Generator Sets

Genset

model

Engine model

Prime power

KW/KVA

Standby

Power

KW/KVA

Fuel

Consumption

≤L/h

dimension mm

Weight kg

AD66

DB58

48/60

53/66

18.1

2100×800×1400

1100

AD96

D1146

70/88

77/96

20.8

2350×900×1300

1500

AD138

D1146T

100/125

110/138

27

2400×900×1300

1600

AD186

P086TI-1

135/169

149/186

48.4

2600×950×1450

1750

AD220

P086TI

160/200

176/220

48.4

2600×950×1450

1825

AD303

P126TI

220/275

242/303

66.2

3000×1000×1650

2200

AD344

P126TI-II

250/313

275/344

77.6

3000×1000×1650

2300

AD413

P158LE-1

300/375

330/413

102.9

3100×1390×1700

2500

AD440

P158LE

320/400

352/440

102.9

3100×1400×1800

2800

AD495

P158LE-S

360/450

396/495

109.7

3300×1400×1800

3050

Generator/Alternators

Little Introduction of An Alternator/Generator:-

In electricity generation, an electric generator is a device that converts mechanical energy to

electrical energy. The reverse conversion of electrical energy into mechanical energy is done by a

motor; motors and generators have many similarities. A generator forces electrons in the windings

to flow through the external electrical circuit. It is somewhat analogous to a water pump, which

creates a flow of water but does not create the water inside. The source of mechanical energy may

be a reciprocating or turbine steam engine, water falling through a turbine or waterwheel, an

internal combustion engine, a wind turbine, a hand crank, compressed air or any other source of

mechanical energy.

Soherwardi Enterprises Pvt Ltd and Soherwardi Engineering supplies you a variety of world

famous generators, from low power to high power and this is the honor of Soherwardi Enterprises

Pvt Ltd and Soherwardi Engineering, our supplied generators are selected by our engineers and

from well reputed manufacturers.

Our supply ability:-

Soherwardi Enterprises Pvt Ltd and Soherwardi Engineering can supply you various famous brands, such

as:-

1. Leroysommer

2. Marathon

3. Stamford

4. Olympian

5. Kajieli

And much more.

Mostly we supply the power range from 10 kva to 2500 kva but on demand we can supply up to 4500 kva.

We also provide the famous , Chinese generators with 100 % assurance of copper winding , and with best efficiency

http://en.wikipedia.org/wiki/Electricity_generation

http://en.wikipedia.org/wiki/Mechanical_energy

http://en.wikipedia.org/wiki/Electrical_energy

http://en.wikipedia.org/wiki/Electric_Motor

http://en.wikipedia.org/wiki/Electrons

http://en.wikipedia.org/wiki/Electrical_circuit

http://en.wiktionary.org/wiki/prime_mover

http://en.wikipedia.org/wiki/Steam_engine

http://en.wikipedia.org/wiki/Hydropower

http://en.wikipedia.org/wiki/Internal_combustion_engine

http://en.wikipedia.org/wiki/Wind_turbine

http://en.wikipedia.org/wiki/Crank_%28mechanism%29

http://en.wikipedia.org/wiki/Compressed_air

ATS/MCU

01: Diesel Generator Control System:-

The DEEPSEA 5110 control system is used to automatically start and stop the generator via remote control

signal, configurable three position includes manual, auto and stop .

Stop: stop generator/failure

Manual: only green manual button to start generator

Auto/remote control: Under working conditions when it is energized, automatically start generator if receiving

remote control

Microprocessor Control: The module features 16-bit microprocessor control and a comprehensive list of

timers and pre-configured sequences. This allows demanding specifications to be achieved. Configurable

expansion facilities are also provided.

02: The DEEPSEA 5220 control system is a low cost generator controller equipped with Auto start/stop

functions, protections, alarms and annunciation etc,monitoring and protections include: running, over speed,

high water temperature, low oil pressure, over crand, emergency stop, and low battery.

All outputs function executed by a set of traditional relays which make it possible to support heavvy power

handing capability, it designed to control engine by a key switch. Users only needs to switch the key to the

manual position then the system will carry out whole function according to your setting. Besides, the

DEEPSEA5220 control system applied with a high security continental terminal connector that provide easy

plug-in and removal.

SEC series Automatic Transfer Switches are an integral part of the power generation process,

allowing smooth and immediate transfer of electrical current between multiple sources and the load. When

the generator is operating, the transfer switch prevents dangerous feedback of current to the utility's

system. It also ensures that different sources are fully synchronized before their power is combined or loads

are transferred, which is imperative of safe operation.

The transfer switch senses when utility power is interrupted, and starts up the generator if the

utility power remains absent. In about five to ten seconds, when the generator is producing full power, the

transfer switch disconnects the load from the utility and connects it to the generator, restoring electricity to

the load. The transfer switch continues to monitor utility power, and when it is restored, switches the load

from the generator back to the utility. Once the generator is disconnected, it goes through a cool-down

routine and is automatically shut down. ATS size is availble from 30 to 3200Amp.

Choosing the right ATS for the generator set,Generator Set Current: = Genset KVA*1000/Voltage/1.732 ATS Size sould be 120% of the generator set current

ATS Cuts Over System Features:

For emergency power usage in building. Auto transfer switch (ATS) is essential ATS can auto transfer load

from mains power supplying to emergency power

When the main power supplying failure or voltage drop below 80% of normal voltage, ATS will auto start

emergency generator set after a preset

Time of 0-10sec(adjustable according to the users). Once generator reach reach at rated speed, the ATS will

transfer the load to emergency generator sets automatically.

The ATS has large variety current as well as load transform is feasible(20-2500A)

Parallel ATS

Generator Parallel Connection:-

Paralleling conditions:

1.

-Generator sets should be equipped with electrical governor system -Incoming generator phase

sequence must be same as main power -Voltage difference is in the limit between generator and

main power -Frequency difference is in the limit between generator and main power -Frequency

difference is in the limit between generator and main power -Phase angle difference is in the

limit between generator and main power

1. Better reliability and continuity of electrical power: The paralleling of generator sets

enhances system performance because they can stand much more load than one genset

do.

1. Convenient maintenance and service: With generator sets operated in paralleling system, servicing

generator sets will not interrupt emergency power to critical system.

1. More economic:

1. -Operator can manage the operating gensets according main power load. It eliminates the

waste of fuel and lubrication oil while bigger power genset carry smaller load

More flexibility for future expansion: Paralleling system offer economy of installing only as much

power as you need, then adding generator set as building power expands

Documents

Product Information